Message ID | 1465726706-12630-1-git-send-email-dev@kresin.me |
---|---|
State | Accepted |
Delegated to: | Richard Weinberger |
Headers | show |
On Sun, Jun 12, 2016 at 12:18 PM, Mathias Kresin <dev@kresin.me> wrote: > Without using the output macros, it isn't possible to suppress these > messages on the console by specifying an appropriate console log level. > > Signed-off-by: Mathias Kresin <dev@kresin.me> > --- > drivers/mtd/nand/nandsim.c | 28 ++++++++++++++-------------- > 1 file changed, 14 insertions(+), 14 deletions(-) > > diff --git a/drivers/mtd/nand/nandsim.c b/drivers/mtd/nand/nandsim.c > index 1eb9344..3cfcc5e 100644 > --- a/drivers/mtd/nand/nandsim.c > +++ b/drivers/mtd/nand/nandsim.c > @@ -769,22 +769,22 @@ static int __init init_nandsim(struct mtd_info *mtd) > if (ns->busw == 16) > NS_WARN("16-bit flashes support wasn't tested\n"); > > - printk("flash size: %llu MiB\n", > + NS_INFO("flash size: %llu MiB\n", > (unsigned long long)ns->geom.totsz >> 20); > - printk("page size: %u bytes\n", ns->geom.pgsz); > - printk("OOB area size: %u bytes\n", ns->geom.oobsz); > - printk("sector size: %u KiB\n", ns->geom.secsz >> 10); > - printk("pages number: %u\n", ns->geom.pgnum); > - printk("pages per sector: %u\n", ns->geom.pgsec); > - printk("bus width: %u\n", ns->busw); > - printk("bits in sector size: %u\n", ns->geom.secshift); > - printk("bits in page size: %u\n", ns->geom.pgshift); > - printk("bits in OOB size: %u\n", ffs(ns->geom.oobsz) - 1); > - printk("flash size with OOB: %llu KiB\n", > + NS_INFO("page size: %u bytes\n", ns->geom.pgsz); > + NS_INFO("OOB area size: %u bytes\n", ns->geom.oobsz); > + NS_INFO("sector size: %u KiB\n", ns->geom.secsz >> 10); > + NS_INFO("pages number: %u\n", ns->geom.pgnum); > + NS_INFO("pages per sector: %u\n", ns->geom.pgsec); > + NS_INFO("bus width: %u\n", ns->busw); > + NS_INFO("bits in sector size: %u\n", ns->geom.secshift); > + NS_INFO("bits in page size: %u\n", ns->geom.pgshift); > + NS_INFO("bits in OOB size: %u\n", ffs(ns->geom.oobsz) - 1); > + NS_INFO("flash size with OOB: %llu KiB\n", > (unsigned long long)ns->geom.totszoob >> 10); > - printk("page address bytes: %u\n", ns->geom.pgaddrbytes); > - printk("sector address bytes: %u\n", ns->geom.secaddrbytes); > - printk("options: %#x\n", ns->options); > + NS_INFO("page address bytes: %u\n", ns->geom.pgaddrbytes); > + NS_INFO("sector address bytes: %u\n", ns->geom.secaddrbytes); > + NS_INFO("options: %#x\n", ns->options); Makes sense. I'll carry this since I'm doing a bigger nandsim facelift.
diff --git a/drivers/mtd/nand/nandsim.c b/drivers/mtd/nand/nandsim.c index 1eb9344..3cfcc5e 100644 --- a/drivers/mtd/nand/nandsim.c +++ b/drivers/mtd/nand/nandsim.c @@ -769,22 +769,22 @@ static int __init init_nandsim(struct mtd_info *mtd) if (ns->busw == 16) NS_WARN("16-bit flashes support wasn't tested\n"); - printk("flash size: %llu MiB\n", + NS_INFO("flash size: %llu MiB\n", (unsigned long long)ns->geom.totsz >> 20); - printk("page size: %u bytes\n", ns->geom.pgsz); - printk("OOB area size: %u bytes\n", ns->geom.oobsz); - printk("sector size: %u KiB\n", ns->geom.secsz >> 10); - printk("pages number: %u\n", ns->geom.pgnum); - printk("pages per sector: %u\n", ns->geom.pgsec); - printk("bus width: %u\n", ns->busw); - printk("bits in sector size: %u\n", ns->geom.secshift); - printk("bits in page size: %u\n", ns->geom.pgshift); - printk("bits in OOB size: %u\n", ffs(ns->geom.oobsz) - 1); - printk("flash size with OOB: %llu KiB\n", + NS_INFO("page size: %u bytes\n", ns->geom.pgsz); + NS_INFO("OOB area size: %u bytes\n", ns->geom.oobsz); + NS_INFO("sector size: %u KiB\n", ns->geom.secsz >> 10); + NS_INFO("pages number: %u\n", ns->geom.pgnum); + NS_INFO("pages per sector: %u\n", ns->geom.pgsec); + NS_INFO("bus width: %u\n", ns->busw); + NS_INFO("bits in sector size: %u\n", ns->geom.secshift); + NS_INFO("bits in page size: %u\n", ns->geom.pgshift); + NS_INFO("bits in OOB size: %u\n", ffs(ns->geom.oobsz) - 1); + NS_INFO("flash size with OOB: %llu KiB\n", (unsigned long long)ns->geom.totszoob >> 10); - printk("page address bytes: %u\n", ns->geom.pgaddrbytes); - printk("sector address bytes: %u\n", ns->geom.secaddrbytes); - printk("options: %#x\n", ns->options); + NS_INFO("page address bytes: %u\n", ns->geom.pgaddrbytes); + NS_INFO("sector address bytes: %u\n", ns->geom.secaddrbytes); + NS_INFO("options: %#x\n", ns->options); if ((ret = alloc_device(ns)) != 0) return ret;
Without using the output macros, it isn't possible to suppress these messages on the console by specifying an appropriate console log level. Signed-off-by: Mathias Kresin <dev@kresin.me> --- drivers/mtd/nand/nandsim.c | 28 ++++++++++++++-------------- 1 file changed, 14 insertions(+), 14 deletions(-)