diff mbox

i2c: add aspeed i2c crontroller

Message ID 1463761675-15227-1-git-send-email-clg@kaod.org
State New
Headers show

Commit Message

Cédric Le Goater May 20, 2016, 4:27 p.m. UTC
The Aspeed AST2400 integrates a set of 14 I2C/SMBus bus controllers
directly connected to ab APB bus which can be programmed as a master
or slave.

This patch offers a device model for the master mode only, slave mode
is not supported.

On the TODO list, we also have :

 - improve and harden the state machine. 
 - bus recovery support (used by the Linux driver).
 - transfer mode state machine bits. this is not strictly necessary as
   it is mostly used for debug. The bus busy bit is deducted from the
   I2C core engine of qemu.
 - support of the pool buffer: 2048 bytes of internal SRAM (not used
   by the Linux driver).

Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
 hw/arm/ast2400.c            |  16 ++
 hw/i2c/Makefile.objs        |   1 +
 hw/i2c/aspeed_i2c.c         | 449 ++++++++++++++++++++++++++++++++++++++++++++
 include/hw/arm/ast2400.h    |   2 +
 include/hw/i2c/aspeed_i2c.h |  62 ++++++
 5 files changed, 530 insertions(+)
 create mode 100644 hw/i2c/aspeed_i2c.c
 create mode 100644 include/hw/i2c/aspeed_i2c.h

Comments

Andrew Jeffery May 23, 2016, 1:41 a.m. UTC | #1
Hi Cédric,

On Fri, 2016-05-20 at 18:27 +0200, Cédric Le Goater wrote:
> The Aspeed AST2400 integrates a set of 14 I2C/SMBus bus controllers
> directly connected to ab APB bus which can be programmed as a master
> or slave.
> 
> This patch offers a device model for the master mode only, slave mode
> is not supported.
> 
> On the TODO list, we also have :
> 
>  - improve and harden the state machine. 
>  - bus recovery support (used by the Linux driver).
>  - transfer mode state machine bits. this is not strictly necessary as
>    it is mostly used for debug. The bus busy bit is deducted from the
>    I2C core engine of qemu.
>  - support of the pool buffer: 2048 bytes of internal SRAM (not used
>    by the Linux driver).
> 
> Signed-off-by: Cédric Le Goater <clg@kaod.org>
> ---
>  hw/arm/ast2400.c            |  16 ++
>  hw/i2c/Makefile.objs        |   1 +
>  hw/i2c/aspeed_i2c.c         | 449 ++++++++++++++++++++++++++++++++++++++++++++
>  include/hw/arm/ast2400.h    |   2 +
>  include/hw/i2c/aspeed_i2c.h |  62 ++++++
>  5 files changed, 530 insertions(+)
>  create mode 100644 hw/i2c/aspeed_i2c.c
>  create mode 100644 include/hw/i2c/aspeed_i2c.h
> 
> diff --git a/hw/arm/ast2400.c b/hw/arm/ast2400.c
> index cf9f37e6a301..4576e67cd483 100644
> --- a/hw/arm/ast2400.c
> +++ b/hw/arm/ast2400.c
> @@ -18,6 +18,7 @@
>  #include "hw/arm/ast2400.h"
>  #include "hw/char/serial.h"
>  #include "hw/boards.h"
> +#include "hw/i2c/aspeed_i2c.h"
>  
>  #define AST2400_UART_5_BASE      0x00184000
>  #define AST2400_IOMEM_SIZE       0x00200000
> @@ -25,6 +26,7 @@
>  #define AST2400_VIC_BASE         0x1E6C0000
>  #define AST2400_SCU_BASE         0x1E6E2000
>  #define AST2400_TIMER_BASE       0x1E782000
> +#define AST2400_I2C_BASE         0x1E78A000
>  
>  static const int uart_irqs[] = { 9, 32, 33, 34, 10 };
>  static const int timer_irqs[] = { 16, 17, 18, 35, 36, 37, 38, 39, };
> @@ -71,6 +73,10 @@ static void ast2400_init(Object *obj)
>      object_initialize(&s->scu, sizeof(s->scu), TYPE_ASPEED_SCU);
>      object_property_add_child(obj, "scu", OBJECT(&s->scu), NULL);
>      qdev_set_parent_bus(DEVICE(&s->scu), sysbus_get_default());

The hunk fails to apply to master as the SCU isn't yet integrated
there. The change to ast2400.h also fails to apply for this reason.

> +
> +    object_initialize(&s->i2c, sizeof(s->i2c), TYPE_ASPEED_I2C);
> +    object_property_add_child(obj, "i2c", OBJECT(&s->i2c), NULL);
> +    qdev_set_parent_bus(DEVICE(&s->i2c), sysbus_get_default());
>  }
>  
>  static void ast2400_realize(DeviceState *dev, Error **errp)
> @@ -143,6 +149,16 @@ static void ast2400_realize(DeviceState *dev, Error **errp)
>          serial_mm_init(&s->iomem, AST2400_UART_5_BASE, 2,
>                         uart5, 38400, serial_hds[0], DEVICE_LITTLE_ENDIAN);
>      }
> +
> +    /* I2C */
> +    object_property_set_bool(OBJECT(&s->i2c), true, "realized", &err);
> +    if (err) {
> +        error_propagate(errp, err);
> +        return;
> +    }
> +    sysbus_mmio_map(SYS_BUS_DEVICE(&s->i2c), 0, AST2400_I2C_BASE);
> +    sysbus_connect_irq(SYS_BUS_DEVICE(&s->i2c), 0,
> +                       qdev_get_gpio_in(DEVICE(&s->vic), 12));
>  }
>  
>  static void ast2400_class_init(ObjectClass *oc, void *data)
> diff --git a/hw/i2c/Makefile.objs b/hw/i2c/Makefile.objs
> index aeb8f38d70f1..1fd54edf4c23 100644
> --- a/hw/i2c/Makefile.objs
> +++ b/hw/i2c/Makefile.objs
> @@ -5,4 +5,5 @@ common-obj-$(CONFIG_APM) += pm_smbus.o
>  common-obj-$(CONFIG_BITBANG_I2C) += bitbang_i2c.o
>  common-obj-$(CONFIG_EXYNOS4) += exynos4210_i2c.o
>  common-obj-$(CONFIG_IMX_I2C) += imx_i2c.o
> +common-obj-$(CONFIG_ASPEED_SOC) += aspeed_i2c.o
>  obj-$(CONFIG_OMAP) += omap_i2c.o
> diff --git a/hw/i2c/aspeed_i2c.c b/hw/i2c/aspeed_i2c.c
> new file mode 100644
> index 000000000000..c56780d7e362
> --- /dev/null
> +++ b/hw/i2c/aspeed_i2c.c
> @@ -0,0 +1,449 @@
> +/*
> + * ARM Aspeed I2C controller
> + *
> + * Copyright (C) 2016 IBM Corp.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * as published by the Free Software Foundation; either version 2
> + * of the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, see .
> + *
> + */
> +
> +#include "qemu/osdep.h"
> +#include "hw/sysbus.h"
> +#include "hw/i2c/aspeed_i2c.h"

Looks like you will need to also #include "qemu/log.h" as well, as
commit 03dd024ff57733a55cd2e455f361d053c81b1b29 cleaned up its
inclusion via hw/hw.h

Otherwise,

Reviewed-by: Andrew Jeffery <andrew@aj.id.au>

> +
> +/* I2C Global Register */
> +
> +#define I2C_CTRL_STATUS         0x00        /* Device Interrupt Status */
> +#define I2C_CTRL_ASSIGN         0x08        /* Device Interrupt Target
> +                                               Assignment */
> +
> +/* I2C Device (Bus) Register */
> +
> +#define I2CD_FUN_CTRL_REG       0x00       /* I2CD Function Control  */
> +#define   I2CD_BUFF_SEL_MASK               (0x7 << 20)
> +#define   I2CD_BUFF_SEL(x)                 (x << 20)
> +#define   I2CD_M_SDA_LOCK_EN               (0x1 << 16)
> +#define   I2CD_MULTI_MASTER_DIS            (0x1 << 15)
> +#define   I2CD_M_SCL_DRIVE_EN              (0x1 << 14)
> +#define   I2CD_MSB_STS                     (0x1 << 9)
> +#define   I2CD_SDA_DRIVE_1T_EN             (0x1 << 8)
> +#define   I2CD_M_SDA_DRIVE_1T_EN           (0x1 << 7)
> +#define   I2CD_M_HIGH_SPEED_EN             (0x1 << 6)
> +#define   I2CD_DEF_ADDR_EN                 (0x1 << 5)
> +#define   I2CD_DEF_ALERT_EN                (0x1 << 4)
> +#define   I2CD_DEF_ARP_EN                  (0x1 << 3)
> +#define   I2CD_DEF_GCALL_EN                (0x1 << 2)
> +#define   I2CD_SLAVE_EN                    (0x1 << 1)
> +#define   I2CD_MASTER_EN                   (0x1)
> +
> +#define I2CD_AC_TIMING_REG1     0x04       /* Clock and AC Timing Control #1 */
> +#define I2CD_AC_TIMING_REG2     0x08       /* Clock and AC Timing Control #1 */
> +#define I2CD_INTR_CTRL_REG      0x0c       /* I2CD Interrupt Control */
> +#define I2CD_INTR_STS_REG       0x10       /* I2CD Interrupt Status */
> +#define   I2CD_INTR_SDA_DL_TIMEOUT         (0x1 << 14)
> +#define   I2CD_INTR_BUS_RECOVER_DONE       (0x1 << 13)
> +#define   I2CD_INTR_SMBUS_ALERT            (0x1 << 12) /* Bus [0-3] only */
> +#define   I2CD_INTR_SMBUS_ARP_ADDR         (0x1 << 11) /* Removed */
> +#define   I2CD_INTR_SMBUS_DEV_ALERT_ADDR   (0x1 << 10) /* Removed */
> +#define   I2CD_INTR_SMBUS_DEF_ADDR         (0x1 << 9)  /* Removed */
> +#define   I2CD_INTR_GCALL_ADDR             (0x1 << 8)  /* Removed */
> +#define   I2CD_INTR_SLAVE_MATCH            (0x1 << 7)  /* use RX_DONE */
> +#define   I2CD_INTR_SCL_TIMEOUT            (0x1 << 6)
> +#define   I2CD_INTR_ABNORMAL               (0x1 << 5)
> +#define   I2CD_INTR_NORMAL_STOP            (0x1 << 4)
> +#define   I2CD_INTR_ARBIT_LOSS             (0x1 << 3)
> +#define   I2CD_INTR_RX_DONE                (0x1 << 2)
> +#define   I2CD_INTR_TX_NAK                 (0x1 << 1)
> +#define   I2CD_INTR_TX_ACK                 (0x1 << 0)
> +
> +#define I2CD_CMD_REG            0x14       /* I2CD Command/Status */
> +#define   I2CD_SDA_OE                      (0x1 << 28)
> +#define   I2CD_SDA_O                       (0x1 << 27)
> +#define   I2CD_SCL_OE                      (0x1 << 26)
> +#define   I2CD_SCL_O                       (0x1 << 25)
> +#define   I2CD_TX_TIMING                   (0x1 << 24)
> +#define   I2CD_TX_STATUS                   (0x1 << 23)
> +
> +#define   I2CD_TX_STATE_SHIFT              19 /* Tx State Machine */
> +#define   I2CD_TX_STATE_MASK                  0xf
> +#define     I2CD_IDLE                         0x0
> +#define     I2CD_MACTIVE                      0x8
> +#define     I2CD_MSTART                       0x9
> +#define     I2CD_MSTARTR                      0xa
> +#define     I2CD_MSTOP                        0xb
> +#define     I2CD_MTXD                         0xc
> +#define     I2CD_MRXACK                       0xd
> +#define     I2CD_MRXD                         0xe
> +#define     I2CD_MTXACK                       0xf
> +#define     I2CD_SWAIT                        0x1
> +#define     I2CD_SRXD                         0x4
> +#define     I2CD_STXACK                       0x5
> +#define     I2CD_STXD                         0x6
> +#define     I2CD_SRXACK                       0x7
> +#define     I2CD_RECOVER                      0x3
> +
> +#define   I2CD_SCL_LINE_STS                (0x1 << 18)
> +#define   I2CD_SDA_LINE_STS                (0x1 << 17)
> +#define   I2CD_BUS_BUSY_STS                (0x1 << 16)
> +#define   I2CD_SDA_OE_OUT_DIR              (0x1 << 15)
> +#define   I2CD_SDA_O_OUT_DIR               (0x1 << 14)
> +#define   I2CD_SCL_OE_OUT_DIR              (0x1 << 13)
> +#define   I2CD_SCL_O_OUT_DIR               (0x1 << 12)
> +#define   I2CD_BUS_RECOVER_CMD_EN          (0x1 << 11)
> +#define   I2CD_S_ALT_EN                    (0x1 << 10)
> +#define   I2CD_RX_DMA_ENABLE               (0x1 << 9)
> +#define   I2CD_TX_DMA_ENABLE               (0x1 << 8)
> +
> +/* Command Bit */
> +#define   I2CD_M_STOP_CMD                  (0x1 << 5)
> +#define   I2CD_M_S_RX_CMD_LAST             (0x1 << 4)
> +#define   I2CD_M_RX_CMD                    (0x1 << 3)
> +#define   I2CD_S_TX_CMD                    (0x1 << 2)
> +#define   I2CD_M_TX_CMD                    (0x1 << 1)
> +#define   I2CD_M_START_CMD                 (0x1)
> +
> +#define I2CD_DEV_ADDR_REG       0x18       /* Slave Device Address */
> +#define I2CD_BUF_CTRL_REG       0x1c       /* Pool Buffer Control */
> +#define I2CD_BYTE_BUF_REG       0x20       /* Transmit/Receive Byte Buffer */
> +#define   I2CD_BYTE_BUF_TX_SHIFT           0
> +#define   I2CD_BYTE_BUF_TX_MASK            0xff
> +#define   I2CD_BYTE_BUF_RX_SHIFT           8
> +#define   I2CD_BYTE_BUF_RX_MASK            0xff
> +
> +
> +static inline bool aspeed_i2c_bus_is_master(AspeedI2CBus *bus)
> +{
> +    return bus->ctrl & I2CD_MASTER_EN;
> +}
> +
> +static inline bool aspeed_i2c_bus_is_enabled(AspeedI2CBus *bus)
> +{
> +    return bus->ctrl & (I2CD_MASTER_EN | I2CD_SLAVE_EN);
> +}
> +
> +static inline void aspeed_i2c_bus_raise_interrupt(AspeedI2CBus *bus)
> +{
> +    bus->intr_status &= bus->intr_ctrl;
> +    if (bus->intr_status) {
> +        bus->controller->intr_status |= 1 << bus->id;
> +        qemu_irq_raise(bus->controller->irq);
> +    }
> +}
> +
> +static uint64_t aspeed_i2c_bus_read(void *opaque, hwaddr offset,
> +                                    unsigned size)
> +{
> +    AspeedI2CBus *bus = opaque;
> +
> +    switch (offset) {
> +    case I2CD_FUN_CTRL_REG:
> +        return bus->ctrl;
> +    case I2CD_AC_TIMING_REG1:
> +        return bus->timing[0];
> +    case I2CD_AC_TIMING_REG2:
> +        return bus->timing[1];
> +    case I2CD_INTR_CTRL_REG:
> +        return bus->intr_ctrl;
> +    case I2CD_INTR_STS_REG:
> +        return bus->intr_status;
> +    case I2CD_BYTE_BUF_REG:
> +        return bus->buf;
> +    case I2CD_CMD_REG:
> +        return bus->cmd | (i2c_bus_busy(bus->bus) << 16);
> +    default:
> +        qemu_log_mask(LOG_GUEST_ERROR,
> +                      "%s: Bad offset 0x%" HWADDR_PRIx "\n", __func__, offset);
> +        return -1;
> +    }
> +}
> +
> +static inline uint64_t aspeed_i2c_bus_get_state(AspeedI2CBus *bus)
> +{
> +    return bus->cmd >> 19 & 0xF;
> +}
> +
> +static inline void aspeed_i2c_bus_set_state(AspeedI2CBus *bus, uint64_t value)
> +{
> +    bus->cmd |= (value & 0xF) << 19;
> +}
> +
> +static void aspeed_i2c_bus_handle_cmd(AspeedI2CBus *bus, uint64_t value)
> +{
> +    bus->cmd |= value & 0xFFFF;
> +    bus->intr_status = 0;
> +
> +    if (bus->cmd & I2CD_M_START_CMD) {
> +        if (i2c_start_transfer(bus->bus, extract32(bus->buf, 1, 7),
> +                               extract32(bus->buf, 0, 1))) {
> +            bus->intr_status |= I2CD_INTR_TX_NAK;
> +        } else {
> +            bus->intr_status |= I2CD_INTR_TX_ACK;
> +        }
> +
> +    } else if (bus->cmd & I2CD_M_TX_CMD) {
> +        if (i2c_send(bus->bus, bus->buf)) {
> +            bus->intr_status |= (I2CD_INTR_TX_NAK | I2CD_INTR_ABNORMAL);
> +            i2c_end_transfer(bus->bus);
> +        } else {
> +            bus->intr_status |= I2CD_INTR_TX_ACK;
> +        }
> +
> +    } else if (bus->cmd & I2CD_M_RX_CMD) {
> +        int ret = i2c_recv(bus->bus);
> +        if (ret < 0) {
> +            qemu_log_mask(LOG_GUEST_ERROR, "%s: read failed\n", __func__);
> +            ret = 0xff;
> +        } else {
> +            bus->intr_status |= I2CD_INTR_RX_DONE;
> +        }
> +        bus->buf = (ret & I2CD_BYTE_BUF_RX_MASK) << I2CD_BYTE_BUF_RX_SHIFT;
> +    }
> +
> +    if (bus->cmd & (I2CD_M_STOP_CMD | I2CD_M_S_RX_CMD_LAST)) {
> +        if (!i2c_bus_busy(bus->bus)) {
> +            bus->intr_status |= I2CD_INTR_ABNORMAL;
> +        } else {
> +            i2c_end_transfer(bus->bus);
> +            bus->intr_status |= I2CD_INTR_NORMAL_STOP;
> +        }
> +    }
> +
> +    /* command is handled, reset it and check for interrupts  */
> +    bus->cmd &= ~0xFFFF;
> +    aspeed_i2c_bus_raise_interrupt(bus);
> +}
> +
> +static void aspeed_i2c_bus_write(void *opaque, hwaddr offset,
> +                                 uint64_t value, unsigned size)
> +{
> +    AspeedI2CBus *bus = opaque;
> +
> +    switch (offset) {
> +    case I2CD_FUN_CTRL_REG:
> +        if (value & I2CD_SLAVE_EN) {
> +            qemu_log_mask(LOG_UNIMP, "%s: slave mode not implemented\n",
> +                          __func__);
> +            break;
> +        }
> +        bus->ctrl = value & 0x0071C3FF;
> +        break;
> +    case I2CD_AC_TIMING_REG1:
> +        bus->timing[0] = value & 0xFFFFF0F;
> +        break;
> +    case I2CD_AC_TIMING_REG2:
> +        bus->timing[1] = value & 0x7;
> +        break;
> +    case I2CD_INTR_CTRL_REG:
> +        bus->intr_ctrl = value & 0x7FFF;
> +        break;
> +    case I2CD_INTR_STS_REG:
> +        bus->intr_status &= ~(value & 0x7FFF);
> +        bus->controller->intr_status &= ~(1 << bus->id);
> +        qemu_irq_lower(bus->controller->irq);
> +        break;
> +    case I2CD_DEV_ADDR_REG:
> +        qemu_log_mask(LOG_UNIMP, "%s: slave mode not implemented\n",
> +                      __func__);
> +        break;
> +    case I2CD_BYTE_BUF_REG:
> +        bus->buf = (value & I2CD_BYTE_BUF_TX_MASK) << I2CD_BYTE_BUF_TX_SHIFT;
> +        break;
> +    case I2CD_CMD_REG:
> +        if (!aspeed_i2c_bus_is_enabled(bus)) {
> +            break;
> +        }
> +
> +        if (!aspeed_i2c_bus_is_master(bus)) {
> +            qemu_log_mask(LOG_UNIMP, "%s: slave mode not implemented\n",
> +                          __func__);
> +            break;
> +        }
> +
> +        aspeed_i2c_bus_handle_cmd(bus, value);
> +        break;
> +
> +    default:
> +        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad offset 0x%" HWADDR_PRIx "\n",
> +                      __func__, offset);
> +    }
> +}
> +
> +static uint64_t aspeed_i2c_ctrl_read(void *opaque, hwaddr offset,
> +                                   unsigned size)
> +{
> +    AspeedI2CState *s = opaque;
> +
> +    switch (offset) {
> +    case I2C_CTRL_STATUS:
> +        return s->intr_status;
> +    default:
> +        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad offset 0x%" HWADDR_PRIx "\n",
> +                      __func__, offset);
> +        break;
> +    }
> +
> +    return -1;
> +}
> +
> +static void aspeed_i2c_ctrl_write(void *opaque, hwaddr offset,
> +                                  uint64_t value, unsigned size)
> +{
> +    switch (offset) {
> +    case I2C_CTRL_STATUS:
> +    default:
> +        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad offset 0x%" HWADDR_PRIx "\n",
> +                      __func__, offset);
> +        break;
> +    }
> +}
> +
> +static const MemoryRegionOps aspeed_i2c_bus_ops = {
> +    .read = aspeed_i2c_bus_read,
> +    .write = aspeed_i2c_bus_write,
> +    .endianness = DEVICE_LITTLE_ENDIAN,
> +};
> +
> +static const MemoryRegionOps aspeed_i2c_ctrl_ops = {
> +    .read = aspeed_i2c_ctrl_read,
> +    .write = aspeed_i2c_ctrl_write,
> +    .endianness = DEVICE_LITTLE_ENDIAN,
> +};
> +
> +static const VMStateDescription aspeed_i2c_bus_vmstate = {
> +    .name = TYPE_ASPEED_I2C,
> +    .version_id = 1,
> +    .minimum_version_id = 1,
> +    .fields = (VMStateField[]) {
> +        VMSTATE_UINT8(id, AspeedI2CBus),
> +        VMSTATE_UINT32(ctrl, AspeedI2CBus),
> +        VMSTATE_UINT32_ARRAY(timing, AspeedI2CBus, 2),
> +        VMSTATE_UINT32(intr_ctrl, AspeedI2CBus),
> +        VMSTATE_UINT32(intr_status, AspeedI2CBus),
> +        VMSTATE_UINT32(cmd, AspeedI2CBus),
> +        VMSTATE_UINT32(buf, AspeedI2CBus),
> +        VMSTATE_END_OF_LIST()
> +    }
> +};
> +
> +static const VMStateDescription aspeed_i2c_vmstate = {
> +    .name = TYPE_ASPEED_I2C,
> +    .version_id = 1,
> +    .minimum_version_id = 1,
> +    .fields = (VMStateField[]) {
> +        VMSTATE_UINT32(intr_status, AspeedI2CState),
> +        VMSTATE_STRUCT_ARRAY(busses, AspeedI2CState,
> +                             ASPEED_I2C_NR_BUSSES, 1, aspeed_i2c_bus_vmstate,
> +                             AspeedI2CBus),
> +        VMSTATE_END_OF_LIST()
> +    }
> +};
> +
> +static void aspeed_i2c_reset(DeviceState *dev)
> +{
> +    int i;
> +    AspeedI2CState *s = ASPEED_I2C(dev);
> +
> +    s->intr_status = 0;
> +
> +    for (i = 0; i < ASPEED_I2C_NR_BUSSES; i++) {
> +        s->busses[i].intr_ctrl = 0;
> +        s->busses[i].intr_status = 0;
> +        s->busses[i].cmd = 0;
> +        s->busses[i].buf = 0;
> +        i2c_end_transfer(s->busses[i].bus);
> +    }
> +}
> +
> +/*
> + * Address Definitions
> + *
> + *   0x000 ... 0x03F: Global Register
> + *   0x040 ... 0x07F: Device 1
> + *   0x080 ... 0x0BF: Device 2
> + *   0x0C0 ... 0x0FF: Device 3
> + *   0x100 ... 0x13F: Device 4
> + *   0x140 ... 0x17F: Device 5
> + *   0x180 ... 0x1BF: Device 6
> + *   0x1C0 ... 0x1FF: Device 7
> + *   0x200 ... 0x2FF: Buffer Pool  (unused in linux driver)
> + *   0x300 ... 0x33F: Device 8
> + *   0x340 ... 0x37F: Device 9
> + *   0x380 ... 0x3BF: Device 10
> + *   0x3C0 ... 0x3FF: Device 11
> + *   0x400 ... 0x43F: Device 12
> + *   0x440 ... 0x47F: Device 13
> + *   0x480 ... 0x4BF: Device 14
> + *   0x800 ... 0xFFF: Buffer Pool  (unused in linux driver)
> + */
> +static void aspeed_i2c_realize(DeviceState *dev, Error **errp)
> +{
> +    int i;
> +    SysBusDevice *sbd = SYS_BUS_DEVICE(dev);
> +    AspeedI2CState *s = ASPEED_I2C(dev);
> +
> +    sysbus_init_irq(sbd, &s->irq);
> +    memory_region_init_io(&s->iomem, OBJECT(s), &aspeed_i2c_ctrl_ops, s,
> +                          "aspeed.i2c", 0x1000);
> +    sysbus_init_mmio(sbd, &s->iomem);
> +
> +    for (i = 0; i < ASPEED_I2C_NR_BUSSES; i++) {
> +        char name[16];
> +        int offset = i < 7 ? 1 : 5;
> +        snprintf(name, sizeof(name), "aspeed.i2c.%d", i);
> +        s->busses[i].controller = s;
> +        s->busses[i].id = i;
> +        s->busses[i].bus = i2c_init_bus(dev, name);
> +        memory_region_init_io(&s->busses[i].mr, OBJECT(dev),
> +                              &aspeed_i2c_bus_ops, &s->busses[i], name, 0x40);
> +        memory_region_add_subregion(&s->iomem, 0x40 * (i + offset),
> +                                    &s->busses[i].mr);
> +    }
> +}
> +
> +static void aspeed_i2c_class_init(ObjectClass *klass, void *data)
> +{
> +    DeviceClass *dc = DEVICE_CLASS(klass);
> +
> +    dc->vmsd = &aspeed_i2c_vmstate;
> +    dc->reset = aspeed_i2c_reset;
> +    dc->realize = aspeed_i2c_realize;
> +    dc->desc = "Aspeed I2C Controller";
> +}
> +
> +static const TypeInfo aspeed_i2c_info = {
> +    .name          = TYPE_ASPEED_I2C,
> +    .parent        = TYPE_SYS_BUS_DEVICE,
> +    .instance_size = sizeof(AspeedI2CState),
> +    .class_init    = aspeed_i2c_class_init,
> +};
> +
> +static void aspeed_i2c_register_types(void)
> +{
> +    type_register_static(&aspeed_i2c_info);
> +}
> +
> +type_init(aspeed_i2c_register_types)
> +
> +
> +I2CBus *aspeed_i2c_get_bus(DeviceState *dev, int busnr)
> +{
> +    AspeedI2CState *s = ASPEED_I2C(dev);
> +    I2CBus *bus = NULL;
> +
> +    if (busnr >= 0 && busnr < ASPEED_I2C_NR_BUSSES) {
> +        bus = s->busses[busnr].bus;
> +    }
> +
> +    return bus;
> +}
> diff --git a/include/hw/arm/ast2400.h b/include/hw/arm/ast2400.h
> index cf7102145355..e96e3db3fbea 100644
> --- a/include/hw/arm/ast2400.h
> +++ b/include/hw/arm/ast2400.h
> @@ -16,6 +16,7 @@
>  #include "hw/intc/aspeed_vic.h"
>  #include "hw/misc/aspeed_scu.h"
>  #include "hw/timer/aspeed_timer.h"
> +#include "hw/i2c/aspeed_i2c.h"
>  
>  typedef struct AST2400State {
>      /*< private >*/
> @@ -28,6 +29,7 @@ typedef struct AST2400State {
>      AspeedVICState vic;
>      AspeedTimerCtrlState timerctrl;
>      AspeedSCUState scu;
> +    AspeedI2CState i2c;
>  } AST2400State;
>  
>  #define TYPE_AST2400 "ast2400"
> diff --git a/include/hw/i2c/aspeed_i2c.h b/include/hw/i2c/aspeed_i2c.h
> new file mode 100644
> index 000000000000..f9020acdef30
> --- /dev/null
> +++ b/include/hw/i2c/aspeed_i2c.h
> @@ -0,0 +1,62 @@
> +/*
> + *  ASPEED AST2400 I2C Controller
> + *
> + *  Copyright (C) 2016 IBM Corp.
> + *
> + *  This program is free software; you can redistribute it and/or modify
> + *  it under the terms of the GNU General Public License as published by
> + *  the Free Software Foundation; either version 2 of the License, or
> + *  (at your option) any later version.
> + *
> + *  This program is distributed in the hope that it will be useful,
> + *  but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *  GNU General Public License for more details.
> + *
> + *  You should have received a copy of the GNU General Public License along
> + *  with this program; if not, write to the Free Software Foundation, Inc.,
> + *  51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
> + */
> +#ifndef ASPEED_I2C_H
> +#define ASPEED_I2C_H
> +
> +#include "hw/i2c/i2c.h"
> +
> +#define TYPE_ASPEED_I2C "aspeed.i2c"
> +#define ASPEED_I2C(obj) \
> +    OBJECT_CHECK(AspeedI2CState, (obj), TYPE_ASPEED_I2C)
> +
> +#define ASPEED_I2C_NR_BUSSES 14
> +
> +struct AspeedI2CState;
> +
> +typedef struct AspeedI2CBus {
> +    struct AspeedI2CState *controller;
> +
> +    MemoryRegion mr;
> +
> +    I2CBus *bus;
> +    uint8_t id;
> +
> +    uint32_t ctrl;
> +    uint32_t timing[2];
> +    uint32_t intr_ctrl;
> +    uint32_t intr_status;
> +    uint32_t cmd;
> +    uint32_t buf;
> +} AspeedI2CBus;
> +
> +typedef struct AspeedI2CState {
> +    SysBusDevice parent_obj;
> +
> +    MemoryRegion iomem;
> +    qemu_irq irq;
> +
> +    uint32_t intr_status;
> +
> +    AspeedI2CBus busses[ASPEED_I2C_NR_BUSSES];
> +} AspeedI2CState;
> +
> +I2CBus *aspeed_i2c_get_bus(DeviceState *dev, int busnr);
> +
> +#endif /* ASPEED_I2C_H */
Cédric Le Goater May 23, 2016, 5:55 a.m. UTC | #2
On 05/23/2016 03:41 AM, Andrew Jeffery wrote:
> Hi Cédric,
> 
> On Fri, 2016-05-20 at 18:27 +0200, Cédric Le Goater wrote:
>> The Aspeed AST2400 integrates a set of 14 I2C/SMBus bus controllers
>> directly connected to ab APB bus which can be programmed as a master
>> or slave.
>>
>> This patch offers a device model for the master mode only, slave mode
>> is not supported.
>>
>> On the TODO list, we also have :
>>
>>  - improve and harden the state machine. 
>>  - bus recovery support (used by the Linux driver).
>>  - transfer mode state machine bits. this is not strictly necessary as
>>    it is mostly used for debug. The bus busy bit is deducted from the
>>    I2C core engine of qemu.
>>  - support of the pool buffer: 2048 bytes of internal SRAM (not used
>>    by the Linux driver).
>>
>> Signed-off-by: Cédric Le Goater <clg@kaod.org>
>> ---
>>  hw/arm/ast2400.c            |  16 ++
>>  hw/i2c/Makefile.objs        |   1 +
>>  hw/i2c/aspeed_i2c.c         | 449 ++++++++++++++++++++++++++++++++++++++++++++
>>  include/hw/arm/ast2400.h    |   2 +
>>  include/hw/i2c/aspeed_i2c.h |  62 ++++++
>>  5 files changed, 530 insertions(+)
>>  create mode 100644 hw/i2c/aspeed_i2c.c
>>  create mode 100644 include/hw/i2c/aspeed_i2c.h
>>
>> diff --git a/hw/arm/ast2400.c b/hw/arm/ast2400.c
>> index cf9f37e6a301..4576e67cd483 100644
>> --- a/hw/arm/ast2400.c
>> +++ b/hw/arm/ast2400.c
>> @@ -18,6 +18,7 @@
>>  #include "hw/arm/ast2400.h"
>>  #include "hw/char/serial.h"
>>  #include "hw/boards.h"
>> +#include "hw/i2c/aspeed_i2c.h"
>>  
>>  #define AST2400_UART_5_BASE      0x00184000
>>  #define AST2400_IOMEM_SIZE       0x00200000
>> @@ -25,6 +26,7 @@
>>  #define AST2400_VIC_BASE         0x1E6C0000
>>  #define AST2400_SCU_BASE         0x1E6E2000
>>  #define AST2400_TIMER_BASE       0x1E782000
>> +#define AST2400_I2C_BASE         0x1E78A000
>>  
>>  static const int uart_irqs[] = { 9, 32, 33, 34, 10 };
>>  static const int timer_irqs[] = { 16, 17, 18, 35, 36, 37, 38, 39, };
>> @@ -71,6 +73,10 @@ static void ast2400_init(Object *obj)
>>      object_initialize(&s->scu, sizeof(s->scu), TYPE_ASPEED_SCU);
>>      object_property_add_child(obj, "scu", OBJECT(&s->scu), NULL);
>>      qdev_set_parent_bus(DEVICE(&s->scu), sysbus_get_default());
> 
> The hunk fails to apply to master as the SCU isn't yet integrated
> there. The change to ast2400.h also fails to apply for this reason.

Ah yes. I am using your branch for this patch. 

So, I will provide you a fix for "qemu/log.h" below  and let you do 
the sending of the SCU device ? or do you want me to send it all ? 

Cheers,

C. 


>> +
>> +    object_initialize(&s->i2c, sizeof(s->i2c), TYPE_ASPEED_I2C);
>> +    object_property_add_child(obj, "i2c", OBJECT(&s->i2c), NULL);
>> +    qdev_set_parent_bus(DEVICE(&s->i2c), sysbus_get_default());
>>  }
>>  
>>  static void ast2400_realize(DeviceState *dev, Error **errp)
>> @@ -143,6 +149,16 @@ static void ast2400_realize(DeviceState *dev, Error **errp)
>>          serial_mm_init(&s->iomem, AST2400_UART_5_BASE, 2,
>>                         uart5, 38400, serial_hds[0], DEVICE_LITTLE_ENDIAN);
>>      }
>> +
>> +    /* I2C */
>> +    object_property_set_bool(OBJECT(&s->i2c), true, "realized", &err);
>> +    if (err) {
>> +        error_propagate(errp, err);
>> +        return;
>> +    }
>> +    sysbus_mmio_map(SYS_BUS_DEVICE(&s->i2c), 0, AST2400_I2C_BASE);
>> +    sysbus_connect_irq(SYS_BUS_DEVICE(&s->i2c), 0,
>> +                       qdev_get_gpio_in(DEVICE(&s->vic), 12));
>>  }
>>  
>>  static void ast2400_class_init(ObjectClass *oc, void *data)
>> diff --git a/hw/i2c/Makefile.objs b/hw/i2c/Makefile.objs
>> index aeb8f38d70f1..1fd54edf4c23 100644
>> --- a/hw/i2c/Makefile.objs
>> +++ b/hw/i2c/Makefile.objs
>> @@ -5,4 +5,5 @@ common-obj-$(CONFIG_APM) += pm_smbus.o
>>  common-obj-$(CONFIG_BITBANG_I2C) += bitbang_i2c.o
>>  common-obj-$(CONFIG_EXYNOS4) += exynos4210_i2c.o
>>  common-obj-$(CONFIG_IMX_I2C) += imx_i2c.o
>> +common-obj-$(CONFIG_ASPEED_SOC) += aspeed_i2c.o
>>  obj-$(CONFIG_OMAP) += omap_i2c.o
>> diff --git a/hw/i2c/aspeed_i2c.c b/hw/i2c/aspeed_i2c.c
>> new file mode 100644
>> index 000000000000..c56780d7e362
>> --- /dev/null
>> +++ b/hw/i2c/aspeed_i2c.c
>> @@ -0,0 +1,449 @@
>> +/*
>> + * ARM Aspeed I2C controller
>> + *
>> + * Copyright (C) 2016 IBM Corp.
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License
>> + * as published by the Free Software Foundation; either version 2
>> + * of the License, or (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program; if not, see .
>> + *
>> + */
>> +
>> +#include "qemu/osdep.h"
>> +#include "hw/sysbus.h"
>> +#include "hw/i2c/aspeed_i2c.h"
> 
> Looks like you will need to also #include "qemu/log.h" as well, as
> commit 03dd024ff57733a55cd2e455f361d053c81b1b29 cleaned up its
> inclusion via hw/hw.h
> 
> Otherwise,
> 
> Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
> 
>> +
>> +/* I2C Global Register */
>> +
>> +#define I2C_CTRL_STATUS         0x00        /* Device Interrupt Status */
>> +#define I2C_CTRL_ASSIGN         0x08        /* Device Interrupt Target
>> +                                               Assignment */
>> +
>> +/* I2C Device (Bus) Register */
>> +
>> +#define I2CD_FUN_CTRL_REG       0x00       /* I2CD Function Control  */
>> +#define   I2CD_BUFF_SEL_MASK               (0x7 << 20)
>> +#define   I2CD_BUFF_SEL(x)                 (x << 20)
>> +#define   I2CD_M_SDA_LOCK_EN               (0x1 << 16)
>> +#define   I2CD_MULTI_MASTER_DIS            (0x1 << 15)
>> +#define   I2CD_M_SCL_DRIVE_EN              (0x1 << 14)
>> +#define   I2CD_MSB_STS                     (0x1 << 9)
>> +#define   I2CD_SDA_DRIVE_1T_EN             (0x1 << 8)
>> +#define   I2CD_M_SDA_DRIVE_1T_EN           (0x1 << 7)
>> +#define   I2CD_M_HIGH_SPEED_EN             (0x1 << 6)
>> +#define   I2CD_DEF_ADDR_EN                 (0x1 << 5)
>> +#define   I2CD_DEF_ALERT_EN                (0x1 << 4)
>> +#define   I2CD_DEF_ARP_EN                  (0x1 << 3)
>> +#define   I2CD_DEF_GCALL_EN                (0x1 << 2)
>> +#define   I2CD_SLAVE_EN                    (0x1 << 1)
>> +#define   I2CD_MASTER_EN                   (0x1)
>> +
>> +#define I2CD_AC_TIMING_REG1     0x04       /* Clock and AC Timing Control #1 */
>> +#define I2CD_AC_TIMING_REG2     0x08       /* Clock and AC Timing Control #1 */
>> +#define I2CD_INTR_CTRL_REG      0x0c       /* I2CD Interrupt Control */
>> +#define I2CD_INTR_STS_REG       0x10       /* I2CD Interrupt Status */
>> +#define   I2CD_INTR_SDA_DL_TIMEOUT         (0x1 << 14)
>> +#define   I2CD_INTR_BUS_RECOVER_DONE       (0x1 << 13)
>> +#define   I2CD_INTR_SMBUS_ALERT            (0x1 << 12) /* Bus [0-3] only */
>> +#define   I2CD_INTR_SMBUS_ARP_ADDR         (0x1 << 11) /* Removed */
>> +#define   I2CD_INTR_SMBUS_DEV_ALERT_ADDR   (0x1 << 10) /* Removed */
>> +#define   I2CD_INTR_SMBUS_DEF_ADDR         (0x1 << 9)  /* Removed */
>> +#define   I2CD_INTR_GCALL_ADDR             (0x1 << 8)  /* Removed */
>> +#define   I2CD_INTR_SLAVE_MATCH            (0x1 << 7)  /* use RX_DONE */
>> +#define   I2CD_INTR_SCL_TIMEOUT            (0x1 << 6)
>> +#define   I2CD_INTR_ABNORMAL               (0x1 << 5)
>> +#define   I2CD_INTR_NORMAL_STOP            (0x1 << 4)
>> +#define   I2CD_INTR_ARBIT_LOSS             (0x1 << 3)
>> +#define   I2CD_INTR_RX_DONE                (0x1 << 2)
>> +#define   I2CD_INTR_TX_NAK                 (0x1 << 1)
>> +#define   I2CD_INTR_TX_ACK                 (0x1 << 0)
>> +
>> +#define I2CD_CMD_REG            0x14       /* I2CD Command/Status */
>> +#define   I2CD_SDA_OE                      (0x1 << 28)
>> +#define   I2CD_SDA_O                       (0x1 << 27)
>> +#define   I2CD_SCL_OE                      (0x1 << 26)
>> +#define   I2CD_SCL_O                       (0x1 << 25)
>> +#define   I2CD_TX_TIMING                   (0x1 << 24)
>> +#define   I2CD_TX_STATUS                   (0x1 << 23)
>> +
>> +#define   I2CD_TX_STATE_SHIFT              19 /* Tx State Machine */
>> +#define   I2CD_TX_STATE_MASK                  0xf
>> +#define     I2CD_IDLE                         0x0
>> +#define     I2CD_MACTIVE                      0x8
>> +#define     I2CD_MSTART                       0x9
>> +#define     I2CD_MSTARTR                      0xa
>> +#define     I2CD_MSTOP                        0xb
>> +#define     I2CD_MTXD                         0xc
>> +#define     I2CD_MRXACK                       0xd
>> +#define     I2CD_MRXD                         0xe
>> +#define     I2CD_MTXACK                       0xf
>> +#define     I2CD_SWAIT                        0x1
>> +#define     I2CD_SRXD                         0x4
>> +#define     I2CD_STXACK                       0x5
>> +#define     I2CD_STXD                         0x6
>> +#define     I2CD_SRXACK                       0x7
>> +#define     I2CD_RECOVER                      0x3
>> +
>> +#define   I2CD_SCL_LINE_STS                (0x1 << 18)
>> +#define   I2CD_SDA_LINE_STS                (0x1 << 17)
>> +#define   I2CD_BUS_BUSY_STS                (0x1 << 16)
>> +#define   I2CD_SDA_OE_OUT_DIR              (0x1 << 15)
>> +#define   I2CD_SDA_O_OUT_DIR               (0x1 << 14)
>> +#define   I2CD_SCL_OE_OUT_DIR              (0x1 << 13)
>> +#define   I2CD_SCL_O_OUT_DIR               (0x1 << 12)
>> +#define   I2CD_BUS_RECOVER_CMD_EN          (0x1 << 11)
>> +#define   I2CD_S_ALT_EN                    (0x1 << 10)
>> +#define   I2CD_RX_DMA_ENABLE               (0x1 << 9)
>> +#define   I2CD_TX_DMA_ENABLE               (0x1 << 8)
>> +
>> +/* Command Bit */
>> +#define   I2CD_M_STOP_CMD                  (0x1 << 5)
>> +#define   I2CD_M_S_RX_CMD_LAST             (0x1 << 4)
>> +#define   I2CD_M_RX_CMD                    (0x1 << 3)
>> +#define   I2CD_S_TX_CMD                    (0x1 << 2)
>> +#define   I2CD_M_TX_CMD                    (0x1 << 1)
>> +#define   I2CD_M_START_CMD                 (0x1)
>> +
>> +#define I2CD_DEV_ADDR_REG       0x18       /* Slave Device Address */
>> +#define I2CD_BUF_CTRL_REG       0x1c       /* Pool Buffer Control */
>> +#define I2CD_BYTE_BUF_REG       0x20       /* Transmit/Receive Byte Buffer */
>> +#define   I2CD_BYTE_BUF_TX_SHIFT           0
>> +#define   I2CD_BYTE_BUF_TX_MASK            0xff
>> +#define   I2CD_BYTE_BUF_RX_SHIFT           8
>> +#define   I2CD_BYTE_BUF_RX_MASK            0xff
>> +
>> +
>> +static inline bool aspeed_i2c_bus_is_master(AspeedI2CBus *bus)
>> +{
>> +    return bus->ctrl & I2CD_MASTER_EN;
>> +}
>> +
>> +static inline bool aspeed_i2c_bus_is_enabled(AspeedI2CBus *bus)
>> +{
>> +    return bus->ctrl & (I2CD_MASTER_EN | I2CD_SLAVE_EN);
>> +}
>> +
>> +static inline void aspeed_i2c_bus_raise_interrupt(AspeedI2CBus *bus)
>> +{
>> +    bus->intr_status &= bus->intr_ctrl;
>> +    if (bus->intr_status) {
>> +        bus->controller->intr_status |= 1 << bus->id;
>> +        qemu_irq_raise(bus->controller->irq);
>> +    }
>> +}
>> +
>> +static uint64_t aspeed_i2c_bus_read(void *opaque, hwaddr offset,
>> +                                    unsigned size)
>> +{
>> +    AspeedI2CBus *bus = opaque;
>> +
>> +    switch (offset) {
>> +    case I2CD_FUN_CTRL_REG:
>> +        return bus->ctrl;
>> +    case I2CD_AC_TIMING_REG1:
>> +        return bus->timing[0];
>> +    case I2CD_AC_TIMING_REG2:
>> +        return bus->timing[1];
>> +    case I2CD_INTR_CTRL_REG:
>> +        return bus->intr_ctrl;
>> +    case I2CD_INTR_STS_REG:
>> +        return bus->intr_status;
>> +    case I2CD_BYTE_BUF_REG:
>> +        return bus->buf;
>> +    case I2CD_CMD_REG:
>> +        return bus->cmd | (i2c_bus_busy(bus->bus) << 16);
>> +    default:
>> +        qemu_log_mask(LOG_GUEST_ERROR,
>> +                      "%s: Bad offset 0x%" HWADDR_PRIx "\n", __func__, offset);
>> +        return -1;
>> +    }
>> +}
>> +
>> +static inline uint64_t aspeed_i2c_bus_get_state(AspeedI2CBus *bus)
>> +{
>> +    return bus->cmd >> 19 & 0xF;
>> +}
>> +
>> +static inline void aspeed_i2c_bus_set_state(AspeedI2CBus *bus, uint64_t value)
>> +{
>> +    bus->cmd |= (value & 0xF) << 19;
>> +}
>> +
>> +static void aspeed_i2c_bus_handle_cmd(AspeedI2CBus *bus, uint64_t value)
>> +{
>> +    bus->cmd |= value & 0xFFFF;
>> +    bus->intr_status = 0;
>> +
>> +    if (bus->cmd & I2CD_M_START_CMD) {
>> +        if (i2c_start_transfer(bus->bus, extract32(bus->buf, 1, 7),
>> +                               extract32(bus->buf, 0, 1))) {
>> +            bus->intr_status |= I2CD_INTR_TX_NAK;
>> +        } else {
>> +            bus->intr_status |= I2CD_INTR_TX_ACK;
>> +        }
>> +
>> +    } else if (bus->cmd & I2CD_M_TX_CMD) {
>> +        if (i2c_send(bus->bus, bus->buf)) {
>> +            bus->intr_status |= (I2CD_INTR_TX_NAK | I2CD_INTR_ABNORMAL);
>> +            i2c_end_transfer(bus->bus);
>> +        } else {
>> +            bus->intr_status |= I2CD_INTR_TX_ACK;
>> +        }
>> +
>> +    } else if (bus->cmd & I2CD_M_RX_CMD) {
>> +        int ret = i2c_recv(bus->bus);
>> +        if (ret < 0) {
>> +            qemu_log_mask(LOG_GUEST_ERROR, "%s: read failed\n", __func__);
>> +            ret = 0xff;
>> +        } else {
>> +            bus->intr_status |= I2CD_INTR_RX_DONE;
>> +        }
>> +        bus->buf = (ret & I2CD_BYTE_BUF_RX_MASK) << I2CD_BYTE_BUF_RX_SHIFT;
>> +    }
>> +
>> +    if (bus->cmd & (I2CD_M_STOP_CMD | I2CD_M_S_RX_CMD_LAST)) {
>> +        if (!i2c_bus_busy(bus->bus)) {
>> +            bus->intr_status |= I2CD_INTR_ABNORMAL;
>> +        } else {
>> +            i2c_end_transfer(bus->bus);
>> +            bus->intr_status |= I2CD_INTR_NORMAL_STOP;
>> +        }
>> +    }
>> +
>> +    /* command is handled, reset it and check for interrupts  */
>> +    bus->cmd &= ~0xFFFF;
>> +    aspeed_i2c_bus_raise_interrupt(bus);
>> +}
>> +
>> +static void aspeed_i2c_bus_write(void *opaque, hwaddr offset,
>> +                                 uint64_t value, unsigned size)
>> +{
>> +    AspeedI2CBus *bus = opaque;
>> +
>> +    switch (offset) {
>> +    case I2CD_FUN_CTRL_REG:
>> +        if (value & I2CD_SLAVE_EN) {
>> +            qemu_log_mask(LOG_UNIMP, "%s: slave mode not implemented\n",
>> +                          __func__);
>> +            break;
>> +        }
>> +        bus->ctrl = value & 0x0071C3FF;
>> +        break;
>> +    case I2CD_AC_TIMING_REG1:
>> +        bus->timing[0] = value & 0xFFFFF0F;
>> +        break;
>> +    case I2CD_AC_TIMING_REG2:
>> +        bus->timing[1] = value & 0x7;
>> +        break;
>> +    case I2CD_INTR_CTRL_REG:
>> +        bus->intr_ctrl = value & 0x7FFF;
>> +        break;
>> +    case I2CD_INTR_STS_REG:
>> +        bus->intr_status &= ~(value & 0x7FFF);
>> +        bus->controller->intr_status &= ~(1 << bus->id);
>> +        qemu_irq_lower(bus->controller->irq);
>> +        break;
>> +    case I2CD_DEV_ADDR_REG:
>> +        qemu_log_mask(LOG_UNIMP, "%s: slave mode not implemented\n",
>> +                      __func__);
>> +        break;
>> +    case I2CD_BYTE_BUF_REG:
>> +        bus->buf = (value & I2CD_BYTE_BUF_TX_MASK) << I2CD_BYTE_BUF_TX_SHIFT;
>> +        break;
>> +    case I2CD_CMD_REG:
>> +        if (!aspeed_i2c_bus_is_enabled(bus)) {
>> +            break;
>> +        }
>> +
>> +        if (!aspeed_i2c_bus_is_master(bus)) {
>> +            qemu_log_mask(LOG_UNIMP, "%s: slave mode not implemented\n",
>> +                          __func__);
>> +            break;
>> +        }
>> +
>> +        aspeed_i2c_bus_handle_cmd(bus, value);
>> +        break;
>> +
>> +    default:
>> +        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad offset 0x%" HWADDR_PRIx "\n",
>> +                      __func__, offset);
>> +    }
>> +}
>> +
>> +static uint64_t aspeed_i2c_ctrl_read(void *opaque, hwaddr offset,
>> +                                   unsigned size)
>> +{
>> +    AspeedI2CState *s = opaque;
>> +
>> +    switch (offset) {
>> +    case I2C_CTRL_STATUS:
>> +        return s->intr_status;
>> +    default:
>> +        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad offset 0x%" HWADDR_PRIx "\n",
>> +                      __func__, offset);
>> +        break;
>> +    }
>> +
>> +    return -1;
>> +}
>> +
>> +static void aspeed_i2c_ctrl_write(void *opaque, hwaddr offset,
>> +                                  uint64_t value, unsigned size)
>> +{
>> +    switch (offset) {
>> +    case I2C_CTRL_STATUS:
>> +    default:
>> +        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad offset 0x%" HWADDR_PRIx "\n",
>> +                      __func__, offset);
>> +        break;
>> +    }
>> +}
>> +
>> +static const MemoryRegionOps aspeed_i2c_bus_ops = {
>> +    .read = aspeed_i2c_bus_read,
>> +    .write = aspeed_i2c_bus_write,
>> +    .endianness = DEVICE_LITTLE_ENDIAN,
>> +};
>> +
>> +static const MemoryRegionOps aspeed_i2c_ctrl_ops = {
>> +    .read = aspeed_i2c_ctrl_read,
>> +    .write = aspeed_i2c_ctrl_write,
>> +    .endianness = DEVICE_LITTLE_ENDIAN,
>> +};
>> +
>> +static const VMStateDescription aspeed_i2c_bus_vmstate = {
>> +    .name = TYPE_ASPEED_I2C,
>> +    .version_id = 1,
>> +    .minimum_version_id = 1,
>> +    .fields = (VMStateField[]) {
>> +        VMSTATE_UINT8(id, AspeedI2CBus),
>> +        VMSTATE_UINT32(ctrl, AspeedI2CBus),
>> +        VMSTATE_UINT32_ARRAY(timing, AspeedI2CBus, 2),
>> +        VMSTATE_UINT32(intr_ctrl, AspeedI2CBus),
>> +        VMSTATE_UINT32(intr_status, AspeedI2CBus),
>> +        VMSTATE_UINT32(cmd, AspeedI2CBus),
>> +        VMSTATE_UINT32(buf, AspeedI2CBus),
>> +        VMSTATE_END_OF_LIST()
>> +    }
>> +};
>> +
>> +static const VMStateDescription aspeed_i2c_vmstate = {
>> +    .name = TYPE_ASPEED_I2C,
>> +    .version_id = 1,
>> +    .minimum_version_id = 1,
>> +    .fields = (VMStateField[]) {
>> +        VMSTATE_UINT32(intr_status, AspeedI2CState),
>> +        VMSTATE_STRUCT_ARRAY(busses, AspeedI2CState,
>> +                             ASPEED_I2C_NR_BUSSES, 1, aspeed_i2c_bus_vmstate,
>> +                             AspeedI2CBus),
>> +        VMSTATE_END_OF_LIST()
>> +    }
>> +};
>> +
>> +static void aspeed_i2c_reset(DeviceState *dev)
>> +{
>> +    int i;
>> +    AspeedI2CState *s = ASPEED_I2C(dev);
>> +
>> +    s->intr_status = 0;
>> +
>> +    for (i = 0; i < ASPEED_I2C_NR_BUSSES; i++) {
>> +        s->busses[i].intr_ctrl = 0;
>> +        s->busses[i].intr_status = 0;
>> +        s->busses[i].cmd = 0;
>> +        s->busses[i].buf = 0;
>> +        i2c_end_transfer(s->busses[i].bus);
>> +    }
>> +}
>> +
>> +/*
>> + * Address Definitions
>> + *
>> + *   0x000 ... 0x03F: Global Register
>> + *   0x040 ... 0x07F: Device 1
>> + *   0x080 ... 0x0BF: Device 2
>> + *   0x0C0 ... 0x0FF: Device 3
>> + *   0x100 ... 0x13F: Device 4
>> + *   0x140 ... 0x17F: Device 5
>> + *   0x180 ... 0x1BF: Device 6
>> + *   0x1C0 ... 0x1FF: Device 7
>> + *   0x200 ... 0x2FF: Buffer Pool  (unused in linux driver)
>> + *   0x300 ... 0x33F: Device 8
>> + *   0x340 ... 0x37F: Device 9
>> + *   0x380 ... 0x3BF: Device 10
>> + *   0x3C0 ... 0x3FF: Device 11
>> + *   0x400 ... 0x43F: Device 12
>> + *   0x440 ... 0x47F: Device 13
>> + *   0x480 ... 0x4BF: Device 14
>> + *   0x800 ... 0xFFF: Buffer Pool  (unused in linux driver)
>> + */
>> +static void aspeed_i2c_realize(DeviceState *dev, Error **errp)
>> +{
>> +    int i;
>> +    SysBusDevice *sbd = SYS_BUS_DEVICE(dev);
>> +    AspeedI2CState *s = ASPEED_I2C(dev);
>> +
>> +    sysbus_init_irq(sbd, &s->irq);
>> +    memory_region_init_io(&s->iomem, OBJECT(s), &aspeed_i2c_ctrl_ops, s,
>> +                          "aspeed.i2c", 0x1000);
>> +    sysbus_init_mmio(sbd, &s->iomem);
>> +
>> +    for (i = 0; i < ASPEED_I2C_NR_BUSSES; i++) {
>> +        char name[16];
>> +        int offset = i < 7 ? 1 : 5;
>> +        snprintf(name, sizeof(name), "aspeed.i2c.%d", i);
>> +        s->busses[i].controller = s;
>> +        s->busses[i].id = i;
>> +        s->busses[i].bus = i2c_init_bus(dev, name);
>> +        memory_region_init_io(&s->busses[i].mr, OBJECT(dev),
>> +                              &aspeed_i2c_bus_ops, &s->busses[i], name, 0x40);
>> +        memory_region_add_subregion(&s->iomem, 0x40 * (i + offset),
>> +                                    &s->busses[i].mr);
>> +    }
>> +}
>> +
>> +static void aspeed_i2c_class_init(ObjectClass *klass, void *data)
>> +{
>> +    DeviceClass *dc = DEVICE_CLASS(klass);
>> +
>> +    dc->vmsd = &aspeed_i2c_vmstate;
>> +    dc->reset = aspeed_i2c_reset;
>> +    dc->realize = aspeed_i2c_realize;
>> +    dc->desc = "Aspeed I2C Controller";
>> +}
>> +
>> +static const TypeInfo aspeed_i2c_info = {
>> +    .name          = TYPE_ASPEED_I2C,
>> +    .parent        = TYPE_SYS_BUS_DEVICE,
>> +    .instance_size = sizeof(AspeedI2CState),
>> +    .class_init    = aspeed_i2c_class_init,
>> +};
>> +
>> +static void aspeed_i2c_register_types(void)
>> +{
>> +    type_register_static(&aspeed_i2c_info);
>> +}
>> +
>> +type_init(aspeed_i2c_register_types)
>> +
>> +
>> +I2CBus *aspeed_i2c_get_bus(DeviceState *dev, int busnr)
>> +{
>> +    AspeedI2CState *s = ASPEED_I2C(dev);
>> +    I2CBus *bus = NULL;
>> +
>> +    if (busnr >= 0 && busnr < ASPEED_I2C_NR_BUSSES) {
>> +        bus = s->busses[busnr].bus;
>> +    }
>> +
>> +    return bus;
>> +}
>> diff --git a/include/hw/arm/ast2400.h b/include/hw/arm/ast2400.h
>> index cf7102145355..e96e3db3fbea 100644
>> --- a/include/hw/arm/ast2400.h
>> +++ b/include/hw/arm/ast2400.h
>> @@ -16,6 +16,7 @@
>>  #include "hw/intc/aspeed_vic.h"
>>  #include "hw/misc/aspeed_scu.h"
>>  #include "hw/timer/aspeed_timer.h"
>> +#include "hw/i2c/aspeed_i2c.h"
>>  
>>  typedef struct AST2400State {
>>      /*< private >*/
>> @@ -28,6 +29,7 @@ typedef struct AST2400State {
>>      AspeedVICState vic;
>>      AspeedTimerCtrlState timerctrl;
>>      AspeedSCUState scu;
>> +    AspeedI2CState i2c;
>>  } AST2400State;
>>  
>>  #define TYPE_AST2400 "ast2400"
>> diff --git a/include/hw/i2c/aspeed_i2c.h b/include/hw/i2c/aspeed_i2c.h
>> new file mode 100644
>> index 000000000000..f9020acdef30
>> --- /dev/null
>> +++ b/include/hw/i2c/aspeed_i2c.h
>> @@ -0,0 +1,62 @@
>> +/*
>> + *  ASPEED AST2400 I2C Controller
>> + *
>> + *  Copyright (C) 2016 IBM Corp.
>> + *
>> + *  This program is free software; you can redistribute it and/or modify
>> + *  it under the terms of the GNU General Public License as published by
>> + *  the Free Software Foundation; either version 2 of the License, or
>> + *  (at your option) any later version.
>> + *
>> + *  This program is distributed in the hope that it will be useful,
>> + *  but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + *  GNU General Public License for more details.
>> + *
>> + *  You should have received a copy of the GNU General Public License along
>> + *  with this program; if not, write to the Free Software Foundation, Inc.,
>> + *  51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
>> + */
>> +#ifndef ASPEED_I2C_H
>> +#define ASPEED_I2C_H
>> +
>> +#include "hw/i2c/i2c.h"
>> +
>> +#define TYPE_ASPEED_I2C "aspeed.i2c"
>> +#define ASPEED_I2C(obj) \
>> +    OBJECT_CHECK(AspeedI2CState, (obj), TYPE_ASPEED_I2C)
>> +
>> +#define ASPEED_I2C_NR_BUSSES 14
>> +
>> +struct AspeedI2CState;
>> +
>> +typedef struct AspeedI2CBus {
>> +    struct AspeedI2CState *controller;
>> +
>> +    MemoryRegion mr;
>> +
>> +    I2CBus *bus;
>> +    uint8_t id;
>> +
>> +    uint32_t ctrl;
>> +    uint32_t timing[2];
>> +    uint32_t intr_ctrl;
>> +    uint32_t intr_status;
>> +    uint32_t cmd;
>> +    uint32_t buf;
>> +} AspeedI2CBus;
>> +
>> +typedef struct AspeedI2CState {
>> +    SysBusDevice parent_obj;
>> +
>> +    MemoryRegion iomem;
>> +    qemu_irq irq;
>> +
>> +    uint32_t intr_status;
>> +
>> +    AspeedI2CBus busses[ASPEED_I2C_NR_BUSSES];
>> +} AspeedI2CState;
>> +
>> +I2CBus *aspeed_i2c_get_bus(DeviceState *dev, int busnr);
>> +
>> +#endif /* ASPEED_I2C_H */
Andrew Jeffery May 23, 2016, 6:20 a.m. UTC | #3
On Mon, 2016-05-23 at 07:55 +0200, Cédric Le Goater wrote:
> > 
> > The hunk fails to apply to master as the SCU isn't yet integrated
> > there. The change to ast2400.h also fails to apply for this reason.
> 
> Ah yes. I am using your branch for this patch. 
> 
> So, I will provide you a fix for "qemu/log.h" below  and let you do 
> the sending of the SCU device ? or do you want me to send it all ? 
> 

I'd make this patch apply to master and send it alone. The SCU patches
aren't quite ready for posting and I've got a few distractions at the
moment, so it might be a week or two before I can clean them up and
send them out. I'll apply them on top of the i2c controller patch when
I get around to it.

Cheers,

Andrew
diff mbox

Patch

diff --git a/hw/arm/ast2400.c b/hw/arm/ast2400.c
index cf9f37e6a301..4576e67cd483 100644
--- a/hw/arm/ast2400.c
+++ b/hw/arm/ast2400.c
@@ -18,6 +18,7 @@ 
 #include "hw/arm/ast2400.h"
 #include "hw/char/serial.h"
 #include "hw/boards.h"
+#include "hw/i2c/aspeed_i2c.h"
 
 #define AST2400_UART_5_BASE      0x00184000
 #define AST2400_IOMEM_SIZE       0x00200000
@@ -25,6 +26,7 @@ 
 #define AST2400_VIC_BASE         0x1E6C0000
 #define AST2400_SCU_BASE         0x1E6E2000
 #define AST2400_TIMER_BASE       0x1E782000
+#define AST2400_I2C_BASE         0x1E78A000
 
 static const int uart_irqs[] = { 9, 32, 33, 34, 10 };
 static const int timer_irqs[] = { 16, 17, 18, 35, 36, 37, 38, 39, };
@@ -71,6 +73,10 @@  static void ast2400_init(Object *obj)
     object_initialize(&s->scu, sizeof(s->scu), TYPE_ASPEED_SCU);
     object_property_add_child(obj, "scu", OBJECT(&s->scu), NULL);
     qdev_set_parent_bus(DEVICE(&s->scu), sysbus_get_default());
+
+    object_initialize(&s->i2c, sizeof(s->i2c), TYPE_ASPEED_I2C);
+    object_property_add_child(obj, "i2c", OBJECT(&s->i2c), NULL);
+    qdev_set_parent_bus(DEVICE(&s->i2c), sysbus_get_default());
 }
 
 static void ast2400_realize(DeviceState *dev, Error **errp)
@@ -143,6 +149,16 @@  static void ast2400_realize(DeviceState *dev, Error **errp)
         serial_mm_init(&s->iomem, AST2400_UART_5_BASE, 2,
                        uart5, 38400, serial_hds[0], DEVICE_LITTLE_ENDIAN);
     }
+
+    /* I2C */
+    object_property_set_bool(OBJECT(&s->i2c), true, "realized", &err);
+    if (err) {
+        error_propagate(errp, err);
+        return;
+    }
+    sysbus_mmio_map(SYS_BUS_DEVICE(&s->i2c), 0, AST2400_I2C_BASE);
+    sysbus_connect_irq(SYS_BUS_DEVICE(&s->i2c), 0,
+                       qdev_get_gpio_in(DEVICE(&s->vic), 12));
 }
 
 static void ast2400_class_init(ObjectClass *oc, void *data)
diff --git a/hw/i2c/Makefile.objs b/hw/i2c/Makefile.objs
index aeb8f38d70f1..1fd54edf4c23 100644
--- a/hw/i2c/Makefile.objs
+++ b/hw/i2c/Makefile.objs
@@ -5,4 +5,5 @@  common-obj-$(CONFIG_APM) += pm_smbus.o
 common-obj-$(CONFIG_BITBANG_I2C) += bitbang_i2c.o
 common-obj-$(CONFIG_EXYNOS4) += exynos4210_i2c.o
 common-obj-$(CONFIG_IMX_I2C) += imx_i2c.o
+common-obj-$(CONFIG_ASPEED_SOC) += aspeed_i2c.o
 obj-$(CONFIG_OMAP) += omap_i2c.o
diff --git a/hw/i2c/aspeed_i2c.c b/hw/i2c/aspeed_i2c.c
new file mode 100644
index 000000000000..c56780d7e362
--- /dev/null
+++ b/hw/i2c/aspeed_i2c.c
@@ -0,0 +1,449 @@ 
+/*
+ * ARM Aspeed I2C controller
+ *
+ * Copyright (C) 2016 IBM Corp.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+#include "qemu/osdep.h"
+#include "hw/sysbus.h"
+#include "hw/i2c/aspeed_i2c.h"
+
+/* I2C Global Register */
+
+#define I2C_CTRL_STATUS         0x00        /* Device Interrupt Status */
+#define I2C_CTRL_ASSIGN         0x08        /* Device Interrupt Target
+                                               Assignment */
+
+/* I2C Device (Bus) Register */
+
+#define I2CD_FUN_CTRL_REG       0x00       /* I2CD Function Control  */
+#define   I2CD_BUFF_SEL_MASK               (0x7 << 20)
+#define   I2CD_BUFF_SEL(x)                 (x << 20)
+#define   I2CD_M_SDA_LOCK_EN               (0x1 << 16)
+#define   I2CD_MULTI_MASTER_DIS            (0x1 << 15)
+#define   I2CD_M_SCL_DRIVE_EN              (0x1 << 14)
+#define   I2CD_MSB_STS                     (0x1 << 9)
+#define   I2CD_SDA_DRIVE_1T_EN             (0x1 << 8)
+#define   I2CD_M_SDA_DRIVE_1T_EN           (0x1 << 7)
+#define   I2CD_M_HIGH_SPEED_EN             (0x1 << 6)
+#define   I2CD_DEF_ADDR_EN                 (0x1 << 5)
+#define   I2CD_DEF_ALERT_EN                (0x1 << 4)
+#define   I2CD_DEF_ARP_EN                  (0x1 << 3)
+#define   I2CD_DEF_GCALL_EN                (0x1 << 2)
+#define   I2CD_SLAVE_EN                    (0x1 << 1)
+#define   I2CD_MASTER_EN                   (0x1)
+
+#define I2CD_AC_TIMING_REG1     0x04       /* Clock and AC Timing Control #1 */
+#define I2CD_AC_TIMING_REG2     0x08       /* Clock and AC Timing Control #1 */
+#define I2CD_INTR_CTRL_REG      0x0c       /* I2CD Interrupt Control */
+#define I2CD_INTR_STS_REG       0x10       /* I2CD Interrupt Status */
+#define   I2CD_INTR_SDA_DL_TIMEOUT         (0x1 << 14)
+#define   I2CD_INTR_BUS_RECOVER_DONE       (0x1 << 13)
+#define   I2CD_INTR_SMBUS_ALERT            (0x1 << 12) /* Bus [0-3] only */
+#define   I2CD_INTR_SMBUS_ARP_ADDR         (0x1 << 11) /* Removed */
+#define   I2CD_INTR_SMBUS_DEV_ALERT_ADDR   (0x1 << 10) /* Removed */
+#define   I2CD_INTR_SMBUS_DEF_ADDR         (0x1 << 9)  /* Removed */
+#define   I2CD_INTR_GCALL_ADDR             (0x1 << 8)  /* Removed */
+#define   I2CD_INTR_SLAVE_MATCH            (0x1 << 7)  /* use RX_DONE */
+#define   I2CD_INTR_SCL_TIMEOUT            (0x1 << 6)
+#define   I2CD_INTR_ABNORMAL               (0x1 << 5)
+#define   I2CD_INTR_NORMAL_STOP            (0x1 << 4)
+#define   I2CD_INTR_ARBIT_LOSS             (0x1 << 3)
+#define   I2CD_INTR_RX_DONE                (0x1 << 2)
+#define   I2CD_INTR_TX_NAK                 (0x1 << 1)
+#define   I2CD_INTR_TX_ACK                 (0x1 << 0)
+
+#define I2CD_CMD_REG            0x14       /* I2CD Command/Status */
+#define   I2CD_SDA_OE                      (0x1 << 28)
+#define   I2CD_SDA_O                       (0x1 << 27)
+#define   I2CD_SCL_OE                      (0x1 << 26)
+#define   I2CD_SCL_O                       (0x1 << 25)
+#define   I2CD_TX_TIMING                   (0x1 << 24)
+#define   I2CD_TX_STATUS                   (0x1 << 23)
+
+#define   I2CD_TX_STATE_SHIFT              19 /* Tx State Machine */
+#define   I2CD_TX_STATE_MASK                  0xf
+#define     I2CD_IDLE                         0x0
+#define     I2CD_MACTIVE                      0x8
+#define     I2CD_MSTART                       0x9
+#define     I2CD_MSTARTR                      0xa
+#define     I2CD_MSTOP                        0xb
+#define     I2CD_MTXD                         0xc
+#define     I2CD_MRXACK                       0xd
+#define     I2CD_MRXD                         0xe
+#define     I2CD_MTXACK                       0xf
+#define     I2CD_SWAIT                        0x1
+#define     I2CD_SRXD                         0x4
+#define     I2CD_STXACK                       0x5
+#define     I2CD_STXD                         0x6
+#define     I2CD_SRXACK                       0x7
+#define     I2CD_RECOVER                      0x3
+
+#define   I2CD_SCL_LINE_STS                (0x1 << 18)
+#define   I2CD_SDA_LINE_STS                (0x1 << 17)
+#define   I2CD_BUS_BUSY_STS                (0x1 << 16)
+#define   I2CD_SDA_OE_OUT_DIR              (0x1 << 15)
+#define   I2CD_SDA_O_OUT_DIR               (0x1 << 14)
+#define   I2CD_SCL_OE_OUT_DIR              (0x1 << 13)
+#define   I2CD_SCL_O_OUT_DIR               (0x1 << 12)
+#define   I2CD_BUS_RECOVER_CMD_EN          (0x1 << 11)
+#define   I2CD_S_ALT_EN                    (0x1 << 10)
+#define   I2CD_RX_DMA_ENABLE               (0x1 << 9)
+#define   I2CD_TX_DMA_ENABLE               (0x1 << 8)
+
+/* Command Bit */
+#define   I2CD_M_STOP_CMD                  (0x1 << 5)
+#define   I2CD_M_S_RX_CMD_LAST             (0x1 << 4)
+#define   I2CD_M_RX_CMD                    (0x1 << 3)
+#define   I2CD_S_TX_CMD                    (0x1 << 2)
+#define   I2CD_M_TX_CMD                    (0x1 << 1)
+#define   I2CD_M_START_CMD                 (0x1)
+
+#define I2CD_DEV_ADDR_REG       0x18       /* Slave Device Address */
+#define I2CD_BUF_CTRL_REG       0x1c       /* Pool Buffer Control */
+#define I2CD_BYTE_BUF_REG       0x20       /* Transmit/Receive Byte Buffer */
+#define   I2CD_BYTE_BUF_TX_SHIFT           0
+#define   I2CD_BYTE_BUF_TX_MASK            0xff
+#define   I2CD_BYTE_BUF_RX_SHIFT           8
+#define   I2CD_BYTE_BUF_RX_MASK            0xff
+
+
+static inline bool aspeed_i2c_bus_is_master(AspeedI2CBus *bus)
+{
+    return bus->ctrl & I2CD_MASTER_EN;
+}
+
+static inline bool aspeed_i2c_bus_is_enabled(AspeedI2CBus *bus)
+{
+    return bus->ctrl & (I2CD_MASTER_EN | I2CD_SLAVE_EN);
+}
+
+static inline void aspeed_i2c_bus_raise_interrupt(AspeedI2CBus *bus)
+{
+    bus->intr_status &= bus->intr_ctrl;
+    if (bus->intr_status) {
+        bus->controller->intr_status |= 1 << bus->id;
+        qemu_irq_raise(bus->controller->irq);
+    }
+}
+
+static uint64_t aspeed_i2c_bus_read(void *opaque, hwaddr offset,
+                                    unsigned size)
+{
+    AspeedI2CBus *bus = opaque;
+
+    switch (offset) {
+    case I2CD_FUN_CTRL_REG:
+        return bus->ctrl;
+    case I2CD_AC_TIMING_REG1:
+        return bus->timing[0];
+    case I2CD_AC_TIMING_REG2:
+        return bus->timing[1];
+    case I2CD_INTR_CTRL_REG:
+        return bus->intr_ctrl;
+    case I2CD_INTR_STS_REG:
+        return bus->intr_status;
+    case I2CD_BYTE_BUF_REG:
+        return bus->buf;
+    case I2CD_CMD_REG:
+        return bus->cmd | (i2c_bus_busy(bus->bus) << 16);
+    default:
+        qemu_log_mask(LOG_GUEST_ERROR,
+                      "%s: Bad offset 0x%" HWADDR_PRIx "\n", __func__, offset);
+        return -1;
+    }
+}
+
+static inline uint64_t aspeed_i2c_bus_get_state(AspeedI2CBus *bus)
+{
+    return bus->cmd >> 19 & 0xF;
+}
+
+static inline void aspeed_i2c_bus_set_state(AspeedI2CBus *bus, uint64_t value)
+{
+    bus->cmd |= (value & 0xF) << 19;
+}
+
+static void aspeed_i2c_bus_handle_cmd(AspeedI2CBus *bus, uint64_t value)
+{
+    bus->cmd |= value & 0xFFFF;
+    bus->intr_status = 0;
+
+    if (bus->cmd & I2CD_M_START_CMD) {
+        if (i2c_start_transfer(bus->bus, extract32(bus->buf, 1, 7),
+                               extract32(bus->buf, 0, 1))) {
+            bus->intr_status |= I2CD_INTR_TX_NAK;
+        } else {
+            bus->intr_status |= I2CD_INTR_TX_ACK;
+        }
+
+    } else if (bus->cmd & I2CD_M_TX_CMD) {
+        if (i2c_send(bus->bus, bus->buf)) {
+            bus->intr_status |= (I2CD_INTR_TX_NAK | I2CD_INTR_ABNORMAL);
+            i2c_end_transfer(bus->bus);
+        } else {
+            bus->intr_status |= I2CD_INTR_TX_ACK;
+        }
+
+    } else if (bus->cmd & I2CD_M_RX_CMD) {
+        int ret = i2c_recv(bus->bus);
+        if (ret < 0) {
+            qemu_log_mask(LOG_GUEST_ERROR, "%s: read failed\n", __func__);
+            ret = 0xff;
+        } else {
+            bus->intr_status |= I2CD_INTR_RX_DONE;
+        }
+        bus->buf = (ret & I2CD_BYTE_BUF_RX_MASK) << I2CD_BYTE_BUF_RX_SHIFT;
+    }
+
+    if (bus->cmd & (I2CD_M_STOP_CMD | I2CD_M_S_RX_CMD_LAST)) {
+        if (!i2c_bus_busy(bus->bus)) {
+            bus->intr_status |= I2CD_INTR_ABNORMAL;
+        } else {
+            i2c_end_transfer(bus->bus);
+            bus->intr_status |= I2CD_INTR_NORMAL_STOP;
+        }
+    }
+
+    /* command is handled, reset it and check for interrupts  */
+    bus->cmd &= ~0xFFFF;
+    aspeed_i2c_bus_raise_interrupt(bus);
+}
+
+static void aspeed_i2c_bus_write(void *opaque, hwaddr offset,
+                                 uint64_t value, unsigned size)
+{
+    AspeedI2CBus *bus = opaque;
+
+    switch (offset) {
+    case I2CD_FUN_CTRL_REG:
+        if (value & I2CD_SLAVE_EN) {
+            qemu_log_mask(LOG_UNIMP, "%s: slave mode not implemented\n",
+                          __func__);
+            break;
+        }
+        bus->ctrl = value & 0x0071C3FF;
+        break;
+    case I2CD_AC_TIMING_REG1:
+        bus->timing[0] = value & 0xFFFFF0F;
+        break;
+    case I2CD_AC_TIMING_REG2:
+        bus->timing[1] = value & 0x7;
+        break;
+    case I2CD_INTR_CTRL_REG:
+        bus->intr_ctrl = value & 0x7FFF;
+        break;
+    case I2CD_INTR_STS_REG:
+        bus->intr_status &= ~(value & 0x7FFF);
+        bus->controller->intr_status &= ~(1 << bus->id);
+        qemu_irq_lower(bus->controller->irq);
+        break;
+    case I2CD_DEV_ADDR_REG:
+        qemu_log_mask(LOG_UNIMP, "%s: slave mode not implemented\n",
+                      __func__);
+        break;
+    case I2CD_BYTE_BUF_REG:
+        bus->buf = (value & I2CD_BYTE_BUF_TX_MASK) << I2CD_BYTE_BUF_TX_SHIFT;
+        break;
+    case I2CD_CMD_REG:
+        if (!aspeed_i2c_bus_is_enabled(bus)) {
+            break;
+        }
+
+        if (!aspeed_i2c_bus_is_master(bus)) {
+            qemu_log_mask(LOG_UNIMP, "%s: slave mode not implemented\n",
+                          __func__);
+            break;
+        }
+
+        aspeed_i2c_bus_handle_cmd(bus, value);
+        break;
+
+    default:
+        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad offset 0x%" HWADDR_PRIx "\n",
+                      __func__, offset);
+    }
+}
+
+static uint64_t aspeed_i2c_ctrl_read(void *opaque, hwaddr offset,
+                                   unsigned size)
+{
+    AspeedI2CState *s = opaque;
+
+    switch (offset) {
+    case I2C_CTRL_STATUS:
+        return s->intr_status;
+    default:
+        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad offset 0x%" HWADDR_PRIx "\n",
+                      __func__, offset);
+        break;
+    }
+
+    return -1;
+}
+
+static void aspeed_i2c_ctrl_write(void *opaque, hwaddr offset,
+                                  uint64_t value, unsigned size)
+{
+    switch (offset) {
+    case I2C_CTRL_STATUS:
+    default:
+        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad offset 0x%" HWADDR_PRIx "\n",
+                      __func__, offset);
+        break;
+    }
+}
+
+static const MemoryRegionOps aspeed_i2c_bus_ops = {
+    .read = aspeed_i2c_bus_read,
+    .write = aspeed_i2c_bus_write,
+    .endianness = DEVICE_LITTLE_ENDIAN,
+};
+
+static const MemoryRegionOps aspeed_i2c_ctrl_ops = {
+    .read = aspeed_i2c_ctrl_read,
+    .write = aspeed_i2c_ctrl_write,
+    .endianness = DEVICE_LITTLE_ENDIAN,
+};
+
+static const VMStateDescription aspeed_i2c_bus_vmstate = {
+    .name = TYPE_ASPEED_I2C,
+    .version_id = 1,
+    .minimum_version_id = 1,
+    .fields = (VMStateField[]) {
+        VMSTATE_UINT8(id, AspeedI2CBus),
+        VMSTATE_UINT32(ctrl, AspeedI2CBus),
+        VMSTATE_UINT32_ARRAY(timing, AspeedI2CBus, 2),
+        VMSTATE_UINT32(intr_ctrl, AspeedI2CBus),
+        VMSTATE_UINT32(intr_status, AspeedI2CBus),
+        VMSTATE_UINT32(cmd, AspeedI2CBus),
+        VMSTATE_UINT32(buf, AspeedI2CBus),
+        VMSTATE_END_OF_LIST()
+    }
+};
+
+static const VMStateDescription aspeed_i2c_vmstate = {
+    .name = TYPE_ASPEED_I2C,
+    .version_id = 1,
+    .minimum_version_id = 1,
+    .fields = (VMStateField[]) {
+        VMSTATE_UINT32(intr_status, AspeedI2CState),
+        VMSTATE_STRUCT_ARRAY(busses, AspeedI2CState,
+                             ASPEED_I2C_NR_BUSSES, 1, aspeed_i2c_bus_vmstate,
+                             AspeedI2CBus),
+        VMSTATE_END_OF_LIST()
+    }
+};
+
+static void aspeed_i2c_reset(DeviceState *dev)
+{
+    int i;
+    AspeedI2CState *s = ASPEED_I2C(dev);
+
+    s->intr_status = 0;
+
+    for (i = 0; i < ASPEED_I2C_NR_BUSSES; i++) {
+        s->busses[i].intr_ctrl = 0;
+        s->busses[i].intr_status = 0;
+        s->busses[i].cmd = 0;
+        s->busses[i].buf = 0;
+        i2c_end_transfer(s->busses[i].bus);
+    }
+}
+
+/*
+ * Address Definitions
+ *
+ *   0x000 ... 0x03F: Global Register
+ *   0x040 ... 0x07F: Device 1
+ *   0x080 ... 0x0BF: Device 2
+ *   0x0C0 ... 0x0FF: Device 3
+ *   0x100 ... 0x13F: Device 4
+ *   0x140 ... 0x17F: Device 5
+ *   0x180 ... 0x1BF: Device 6
+ *   0x1C0 ... 0x1FF: Device 7
+ *   0x200 ... 0x2FF: Buffer Pool  (unused in linux driver)
+ *   0x300 ... 0x33F: Device 8
+ *   0x340 ... 0x37F: Device 9
+ *   0x380 ... 0x3BF: Device 10
+ *   0x3C0 ... 0x3FF: Device 11
+ *   0x400 ... 0x43F: Device 12
+ *   0x440 ... 0x47F: Device 13
+ *   0x480 ... 0x4BF: Device 14
+ *   0x800 ... 0xFFF: Buffer Pool  (unused in linux driver)
+ */
+static void aspeed_i2c_realize(DeviceState *dev, Error **errp)
+{
+    int i;
+    SysBusDevice *sbd = SYS_BUS_DEVICE(dev);
+    AspeedI2CState *s = ASPEED_I2C(dev);
+
+    sysbus_init_irq(sbd, &s->irq);
+    memory_region_init_io(&s->iomem, OBJECT(s), &aspeed_i2c_ctrl_ops, s,
+                          "aspeed.i2c", 0x1000);
+    sysbus_init_mmio(sbd, &s->iomem);
+
+    for (i = 0; i < ASPEED_I2C_NR_BUSSES; i++) {
+        char name[16];
+        int offset = i < 7 ? 1 : 5;
+        snprintf(name, sizeof(name), "aspeed.i2c.%d", i);
+        s->busses[i].controller = s;
+        s->busses[i].id = i;
+        s->busses[i].bus = i2c_init_bus(dev, name);
+        memory_region_init_io(&s->busses[i].mr, OBJECT(dev),
+                              &aspeed_i2c_bus_ops, &s->busses[i], name, 0x40);
+        memory_region_add_subregion(&s->iomem, 0x40 * (i + offset),
+                                    &s->busses[i].mr);
+    }
+}
+
+static void aspeed_i2c_class_init(ObjectClass *klass, void *data)
+{
+    DeviceClass *dc = DEVICE_CLASS(klass);
+
+    dc->vmsd = &aspeed_i2c_vmstate;
+    dc->reset = aspeed_i2c_reset;
+    dc->realize = aspeed_i2c_realize;
+    dc->desc = "Aspeed I2C Controller";
+}
+
+static const TypeInfo aspeed_i2c_info = {
+    .name          = TYPE_ASPEED_I2C,
+    .parent        = TYPE_SYS_BUS_DEVICE,
+    .instance_size = sizeof(AspeedI2CState),
+    .class_init    = aspeed_i2c_class_init,
+};
+
+static void aspeed_i2c_register_types(void)
+{
+    type_register_static(&aspeed_i2c_info);
+}
+
+type_init(aspeed_i2c_register_types)
+
+
+I2CBus *aspeed_i2c_get_bus(DeviceState *dev, int busnr)
+{
+    AspeedI2CState *s = ASPEED_I2C(dev);
+    I2CBus *bus = NULL;
+
+    if (busnr >= 0 && busnr < ASPEED_I2C_NR_BUSSES) {
+        bus = s->busses[busnr].bus;
+    }
+
+    return bus;
+}
diff --git a/include/hw/arm/ast2400.h b/include/hw/arm/ast2400.h
index cf7102145355..e96e3db3fbea 100644
--- a/include/hw/arm/ast2400.h
+++ b/include/hw/arm/ast2400.h
@@ -16,6 +16,7 @@ 
 #include "hw/intc/aspeed_vic.h"
 #include "hw/misc/aspeed_scu.h"
 #include "hw/timer/aspeed_timer.h"
+#include "hw/i2c/aspeed_i2c.h"
 
 typedef struct AST2400State {
     /*< private >*/
@@ -28,6 +29,7 @@  typedef struct AST2400State {
     AspeedVICState vic;
     AspeedTimerCtrlState timerctrl;
     AspeedSCUState scu;
+    AspeedI2CState i2c;
 } AST2400State;
 
 #define TYPE_AST2400 "ast2400"
diff --git a/include/hw/i2c/aspeed_i2c.h b/include/hw/i2c/aspeed_i2c.h
new file mode 100644
index 000000000000..f9020acdef30
--- /dev/null
+++ b/include/hw/i2c/aspeed_i2c.h
@@ -0,0 +1,62 @@ 
+/*
+ *  ASPEED AST2400 I2C Controller
+ *
+ *  Copyright (C) 2016 IBM Corp.
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+#ifndef ASPEED_I2C_H
+#define ASPEED_I2C_H
+
+#include "hw/i2c/i2c.h"
+
+#define TYPE_ASPEED_I2C "aspeed.i2c"
+#define ASPEED_I2C(obj) \
+    OBJECT_CHECK(AspeedI2CState, (obj), TYPE_ASPEED_I2C)
+
+#define ASPEED_I2C_NR_BUSSES 14
+
+struct AspeedI2CState;
+
+typedef struct AspeedI2CBus {
+    struct AspeedI2CState *controller;
+
+    MemoryRegion mr;
+
+    I2CBus *bus;
+    uint8_t id;
+
+    uint32_t ctrl;
+    uint32_t timing[2];
+    uint32_t intr_ctrl;
+    uint32_t intr_status;
+    uint32_t cmd;
+    uint32_t buf;
+} AspeedI2CBus;
+
+typedef struct AspeedI2CState {
+    SysBusDevice parent_obj;
+
+    MemoryRegion iomem;
+    qemu_irq irq;
+
+    uint32_t intr_status;
+
+    AspeedI2CBus busses[ASPEED_I2C_NR_BUSSES];
+} AspeedI2CState;
+
+I2CBus *aspeed_i2c_get_bus(DeviceState *dev, int busnr);
+
+#endif /* ASPEED_I2C_H */