@@ -1,19 +1,20 @@
config USB_DWC3
bool "DesignWare USB3 DRD Core Support"
- depends on (USB && USB_GADGET)
- select USB_GADGET_DUALSPEED
+ select USB_GADGET_DUALSPEED if USB_GADGET
help
- Say Y here if your system has a Dual Role SuperSpeed
- USB controller based on the DesignWare USB3 IP Core.
+ Say Y here if your system has DesignWare USB3 IP Core.
if USB_DWC3
choice
bool "DWC3 Mode Selection"
+ default USB_DWC3_DUAL_ROLE if (USB_GADGET && USB_XHCI_HCD)
+ default USB_DWC3_HOST if (!USB_GADGET && USB_XHCI_HCD)
+ default USB_DWC3_GADGET if (USB_GADGET && !USB_XHCI_HCD)
config USB_DWC3_HOST
bool "Host only mode"
- depends on USB
+ depends on USB_XHCI_HCD
help
Select this when you want to use DWC3 in host mode only,
thereby the gadget feature will be regressed.
@@ -25,6 +26,13 @@ config USB_DWC3_GADGET
Select this when you want to use DWC3 in gadget mode only,
thereby the host feature will be regressed.
+config USB_DWC3_DUAL_ROLE
+ bool "Dual role mode"
+ depends on (USB_XHCI_HCD && USB_GADGET)
+ help
+ This is the default mode of working of DWC3 controller where
+ both host and gadget features are enabled.
+
endchoice
comment "Platform Glue Driver Support"
@@ -6,7 +6,9 @@ obj-$(CONFIG_USB_DWC3) += dwc3.o
dwc3-y := core.o
-dwc3-y += gadget.o ep0.o
+ifneq ($(filter y,$(CONFIG_USB_DWC3_GADGET) $(CONFIG_USB_DWC3_DUAL_ROLE)),)
+dwc3-yi += gadget.o ep0.o
+endif
obj-$(CONFIG_USB_DWC3_OMAP) += dwc3-omap.o
obj-$(CONFIG_USB_DWC3_PHY_OMAP) += ti_usb_phy.o
@@ -989,7 +989,7 @@ struct dwc3_gadget_ep_cmd_params {
/* prototypes */
int dwc3_gadget_resize_tx_fifos(struct dwc3 *dwc);
-#ifdef CONFIG_USB_DWC3_HOST
+#if IS_ENABLED(CONFIG_USB_DWC3_HOST) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
int dwc3_host_init(struct dwc3 *dwc);
void dwc3_host_exit(struct dwc3 *dwc);
#else
@@ -999,7 +999,7 @@ static inline void dwc3_host_exit(struct dwc3 *dwc)
{ }
#endif
-#ifdef CONFIG_USB_DWC3_GADGET
+#if IS_ENABLED(CONFIG_USB_DWC3_GADGET) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
int dwc3_gadget_init(struct dwc3 *dwc);
void dwc3_gadget_exit(struct dwc3 *dwc);
int dwc3_gadget_set_test_mode(struct dwc3 *dwc, int mode);
DWC3 can be used as host or as gadget controller and the actual mode is determined at runtime so USB_DWC3_DUAL_ROLE must be the default mode when both host and gadget drivers are available. As DWC3 core implements an XHCI host controller, we use USB_XHCI_HCD to check if host driver is available. USB_DWC3_HOST and USB_DWC3_GADGET are only set if a particular mode needs to be forced or if both host and gadget drivers are not available. Build the dwc3 gadget drivers only if gadget mode can be used at runtime. Signed-off-by: Roger Quadros <rogerq@ti.com> --- v2: - don't depend on USB as dwc3/kconfig already depends on that - use USB_XHCI_HCD to decide whether host operation is available. - Add USB_DWC3_DUAL_ROLE, which means that controller can operate either in host or gadget mode. The actual mode is decided at runtime based on dwc3->dr_mode. drivers/usb/dwc3/Kconfig | 18 +++++++++++++----- drivers/usb/dwc3/Makefile | 4 +++- drivers/usb/dwc3/core.h | 4 ++-- 3 files changed, 18 insertions(+), 8 deletions(-)