@@ -2629,10 +2629,152 @@ static void evergreen_agp_enable(struct radeon_device *rdev)
WREG32(VM_CONTEXT1_CNTL, 0);
}
+static const unsigned ni_dig_offsets[] =
+{
+ NI_DIG0_REGISTER_OFFSET,
+ NI_DIG1_REGISTER_OFFSET,
+ NI_DIG2_REGISTER_OFFSET,
+ NI_DIG3_REGISTER_OFFSET,
+ NI_DIG4_REGISTER_OFFSET,
+ NI_DIG5_REGISTER_OFFSET
+};
+
+static const unsigned ni_tx_offsets[] =
+{
+ NI_DCIO_UNIPHY0_UNIPHY_TX_CONTROL1,
+ NI_DCIO_UNIPHY1_UNIPHY_TX_CONTROL1,
+ NI_DCIO_UNIPHY2_UNIPHY_TX_CONTROL1,
+ NI_DCIO_UNIPHY3_UNIPHY_TX_CONTROL1,
+ NI_DCIO_UNIPHY4_UNIPHY_TX_CONTROL1,
+ NI_DCIO_UNIPHY5_UNIPHY_TX_CONTROL1
+};
+
+static const unsigned evergreen_dp_offsets[] =
+{
+ EVERGREEN_DP0_REGISTER_OFFSET,
+ EVERGREEN_DP1_REGISTER_OFFSET,
+ EVERGREEN_DP2_REGISTER_OFFSET,
+ EVERGREEN_DP3_REGISTER_OFFSET,
+ EVERGREEN_DP4_REGISTER_OFFSET,
+ EVERGREEN_DP5_REGISTER_OFFSET
+};
+
+
+/*
+ * Assumption is that EVERGREEN_CRTC_MASTER_EN enable for requested crtc
+ * We go from crtc to connector and it is not relible since it
+ * should be an opposite direction .If crtc is enable then
+ * find the dig_fe which selects this crtc and insure that it enable.
+ * if such dig_fe is found then find dig_be which selects found dig_be and
+ * insure that it enable and in DP_SST mode.
+ * if UNIPHY_PLL_CONTROL1.enable then we should disconnect timing
+ * from dp symbols clocks .
+ */
+static bool evergreen_is_dp_sst_stream_enabled(struct radeon_device *rdev,
+ unsigned crtc_id, unsigned *ret_dig_fe)
+{
+ unsigned i;
+ unsigned dig_fe;
+ unsigned dig_be;
+ unsigned dig_en_be;
+ unsigned uniphy_pll;
+ unsigned digs_fe_selected;
+ unsigned dig_be_mode;
+ unsigned dig_fe_mask;
+ bool is_enabled = false;
+ bool found_crtc = false;
+
+ /* loop through all running dig_fe to find selected crtc */
+ for (i = 0; i < ARRAY_SIZE(ni_dig_offsets); i++) {
+ dig_fe = RREG32(NI_DIG_FE_CNTL + ni_dig_offsets[i]);
+ if (dig_fe & NI_DIG_FE_CNTL_SYMCLK_FE_ON &&
+ crtc_id == NI_DIG_FE_CNTL_SOURCE_SELECT(dig_fe)) {
+ /* found running pipe */
+ found_crtc = true;
+ dig_fe_mask = 1 << i;
+ dig_fe = i;
+ break;
+ }
+ }
+
+ if (found_crtc) {
+ /* loop through all running dig_be to find selected dig_fe */
+ for (i = 0; i < ARRAY_SIZE(ni_dig_offsets); i++) {
+ dig_be = RREG32(NI_DIG_BE_CNTL + ni_dig_offsets[i]);
+ /* if dig_fe_selected by dig_be? */
+ digs_fe_selected = NI_DIG_BE_CNTL_FE_SOURCE_SELECT(dig_be);
+ dig_be_mode = NI_DIG_FE_CNTL_MODE(dig_be);
+ if (dig_fe_mask & digs_fe_selected &&
+ /* if dig_be in sst mode? */
+ dig_be_mode == NI_DIG_BE_DPSST) {
+ dig_en_be = RREG32(NI_DIG_BE_EN_CNTL +
+ ni_dig_offsets[i]);
+ uniphy_pll = RREG32(NI_DCIO_UNIPHY0_PLL_CONTROL1 +
+ ni_tx_offsets[i]);
+ /* dig_be enable and tx is running */
+ if (dig_en_be & NI_DIG_BE_EN_CNTL_ENABLE &&
+ dig_en_be & NI_DIG_BE_EN_CNTL_SYMBCLK_ON &&
+ uniphy_pll & NI_DCIO_UNIPHY0_PLL_CONTROL1_ENABLE) {
+ is_enabled = true;
+ *ret_dig_fe = dig_fe;
+ break;
+ }
+ }
+ }
+ }
+
+ return is_enabled;
+}
+
+/*
+ * Blank dig when in dp sst mode
+ * Dig ignores crtc timing
+ */
+static void evergreen_blank_dp_output(struct radeon_device *rdev,
+ unsigned dig_fe)
+{
+ unsigned stream_ctrl;
+ unsigned fifo_ctrl;
+ unsigned counter = 0;
+
+ if (dig_fe >= ARRAY_SIZE(evergreen_dp_offsets)) {
+ DRM_ERROR("invalid dig_fe %d\n", dig_fe);
+ return;
+ }
+
+ stream_ctrl = RREG32(EVERGREEN_DP_VID_STREAM_CNTL +
+ evergreen_dp_offsets[dig_fe]);
+ if (!(stream_ctrl & EVERGREEN_DP_VID_STREAM_CNTL_ENABLE)) {
+ DRM_ERROR("dig %d , should be enable\n", dig_fe);
+ return;
+ }
+
+ stream_ctrl &=~EVERGREEN_DP_VID_STREAM_CNTL_ENABLE;
+ WREG32(EVERGREEN_DP_VID_STREAM_CNTL +
+ evergreen_dp_offsets[dig_fe], stream_ctrl);
+
+ stream_ctrl = RREG32(EVERGREEN_DP_VID_STREAM_CNTL +
+ evergreen_dp_offsets[dig_fe]);
+ while (counter < 32 && stream_ctrl & EVERGREEN_DP_VID_STREAM_STATUS) {
+ msleep(1);
+ counter++;
+ stream_ctrl = RREG32(EVERGREEN_DP_VID_STREAM_CNTL +
+ evergreen_dp_offsets[dig_fe]);
+ }
+ if (counter >= 32 )
+ DRM_ERROR("counter exceeds %d\n", counter);
+
+ fifo_ctrl = RREG32(EVERGREEN_DP_STEER_FIFO + evergreen_dp_offsets[dig_fe]);
+ fifo_ctrl |= EVERGREEN_DP_STEER_FIFO_RESET;
+ WREG32(EVERGREEN_DP_STEER_FIFO + evergreen_dp_offsets[dig_fe], fifo_ctrl);
+
+}
+
void evergreen_mc_stop(struct radeon_device *rdev, struct evergreen_mc_save *save)
{
u32 crtc_enabled, tmp, frame_count, blackout;
int i, j;
+ unsigned dig_fe;
if (!ASIC_IS_NODCE(rdev)) {
save->vga_render_control = RREG32(VGA_RENDER_CONTROL);
@@ -2672,7 +2814,17 @@ void evergreen_mc_stop(struct radeon_device *rdev, struct evergreen_mc_save *sav
break;
udelay(1);
}
-
+ /*we should disable dig if it drives dp sst*/
+ /*but we are in radeon_device_init and the topology is unknown*/
+ /*and it is available after radeon_modeset_init*/
+ /*the following method radeon_atom_encoder_dpms_dig*/
+ /*does the job if we initialize it properly*/
+ /*for now we do it this manually*/
+ /**/
+ if (ASIC_IS_DCE5(rdev) &&
+ evergreen_is_dp_sst_stream_enabled(rdev, i ,&dig_fe))
+ evergreen_blank_dp_output(rdev, dig_fe);
+ /*we could remove 6 lines below*/
/* XXX this is a hack to avoid strange behavior with EFI on certain systems */
WREG32(EVERGREEN_CRTC_UPDATE_LOCK + crtc_offsets[i], 1);
tmp = RREG32(EVERGREEN_CRTC_CONTROL + crtc_offsets[i]);
@@ -250,8 +250,43 @@
/* HDMI blocks at 0x7030, 0x7c30, 0x10830, 0x11430, 0x12030, 0x12c30 */
#define EVERGREEN_HDMI_BASE 0x7030
+/*DIG block*/
+#define NI_DIG0_REGISTER_OFFSET (0x7000 - 0x7000)
+#define NI_DIG1_REGISTER_OFFSET (0x7C00 - 0x7000)
+#define NI_DIG2_REGISTER_OFFSET (0x10800 - 0x7000)
+#define NI_DIG3_REGISTER_OFFSET (0x11400 - 0x7000)
+#define NI_DIG4_REGISTER_OFFSET (0x12000 - 0x7000)
+#define NI_DIG5_REGISTER_OFFSET (0x12C00 - 0x7000)
+
+
+#define NI_DIG_FE_CNTL 0x7000
+# define NI_DIG_FE_CNTL_SOURCE_SELECT(x) ((x) & 0x3)
+# define NI_DIG_FE_CNTL_SYMCLK_FE_ON (1<<24)
+
+
+#define NI_DIG_BE_CNTL 0x7140
+# define NI_DIG_BE_CNTL_FE_SOURCE_SELECT(x) (((x) >> 8 ) & 0x3F)
+# define NI_DIG_FE_CNTL_MODE(x) (((x) >> 16) & 0x7 )
+
+#define NI_DIG_BE_EN_CNTL 0x7144
+# define NI_DIG_BE_EN_CNTL_ENABLE (1 << 0)
+# define NI_DIG_BE_EN_CNTL_SYMBCLK_ON (1 << 8)
+# define NI_DIG_BE_DPSST 0
/* Display Port block */
+#define EVERGREEN_DP0_REGISTER_OFFSET (0x730C - 0x730C)
+#define EVERGREEN_DP1_REGISTER_OFFSET (0x7F0C - 0x730C)
+#define EVERGREEN_DP2_REGISTER_OFFSET (0x10B0C - 0x730C)
+#define EVERGREEN_DP3_REGISTER_OFFSET (0x1170C - 0x730C)
+#define EVERGREEN_DP4_REGISTER_OFFSET (0x1230C - 0x730C)
+#define EVERGREEN_DP5_REGISTER_OFFSET (0x12F0C - 0x730C)
+
+
+#define EVERGREEN_DP_VID_STREAM_CNTL 0x730C
+# define EVERGREEN_DP_VID_STREAM_CNTL_ENABLE (1 << 0)
+# define EVERGREEN_DP_VID_STREAM_STATUS (1 <<16)
+#define EVERGREEN_DP_STEER_FIFO 0x7310
+# define EVERGREEN_DP_STEER_FIFO_RESET (1 << 0)
#define EVERGREEN_DP_SEC_CNTL 0x7280
# define EVERGREEN_DP_SEC_STREAM_ENABLE (1 << 0)
# define EVERGREEN_DP_SEC_ASP_ENABLE (1 << 4)
@@ -266,4 +301,15 @@
# define EVERGREEN_DP_SEC_N_BASE_MULTIPLE(x) (((x) & 0xf) << 24)
# define EVERGREEN_DP_SEC_SS_EN (1 << 28)
+/*DCIO_UNIPHY block*/
+#define NI_DCIO_UNIPHY0_UNIPHY_TX_CONTROL1 (0x6600 -0x6600)
+#define NI_DCIO_UNIPHY1_UNIPHY_TX_CONTROL1 (0x6640 -0x6600)
+#define NI_DCIO_UNIPHY2_UNIPHY_TX_CONTROL1 (0x6680 - 0x6600)
+#define NI_DCIO_UNIPHY3_UNIPHY_TX_CONTROL1 (0x66C0 - 0x6600)
+#define NI_DCIO_UNIPHY4_UNIPHY_TX_CONTROL1 (0x6700 - 0x6600)
+#define NI_DCIO_UNIPHY5_UNIPHY_TX_CONTROL1 (0x6740 - 0x6600)
+
+#define NI_DCIO_UNIPHY0_PLL_CONTROL1 0x6618
+# define NI_DCIO_UNIPHY0_PLL_CONTROL1_ENABLE (1 << 0)
+
#endif
This is a note to let you know that I have just added a patch titled drm/radeon: fix vertical bars appear on monitor (v2) to the linux-4.2.y-queue branch of the 4.2.y-ckt extended stable tree which can be found at: https://git.launchpad.net/~canonical-kernel/linux/+git/linux-stable-ckt/log/?h=linux-4.2.y-queue This patch is scheduled to be released in version 4.2.8-ckt10. If you, or anyone else, feels it should not be added to this tree, please reply to this email. For more information about the 4.2.y-ckt tree, see https://wiki.ubuntu.com/Kernel/Dev/ExtendedStable Thanks. -Kamal ---8<------------------------------------------------------------ From 585fc776361aa018abe288da77c3be50a0224cec Mon Sep 17 00:00:00 2001 From: Vitaly Prosyak <vitaly.prosyak@amd.com> Date: Thu, 14 Apr 2016 13:34:03 -0400 Subject: drm/radeon: fix vertical bars appear on monitor (v2) commit 5d5b7803c49bbb01bdf4c6e95e8314d0515b9484 upstream. When crtc/timing is disabled on boot the dig block should be stopped in order ignore timing from crtc, reset the steering fifo otherwise we get display corruption or hung in dp sst mode. v2: agd: fix coding style Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com> --- drivers/gpu/drm/radeon/evergreen.c | 154 ++++++++++++++++++++++++++++++++- drivers/gpu/drm/radeon/evergreen_reg.h | 46 ++++++++++ 2 files changed, 199 insertions(+), 1 deletion(-) -- 2.7.4