diff mbox

[U-Boot,v8,2/7] net: zynq_gem: Add the passing of the phy-handle node

Message ID 1462221962-13988-2-git-send-email-dmurphy@ti.com
State Accepted
Commit 562a900
Delegated to: Joe Hershberger
Headers show

Commit Message

Dan Murphy May 2, 2016, 8:45 p.m. UTC 
Add the ability to pass the phy-handle node offset
to the phy driver.  This allows the phy driver
to access the DT subnode's data and parse accordingly.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
---

v8 - Add acked/Tested/reviewed by information
v7 - no changes from v6

 drivers/net/zynq_gem.c | 15 ++++++++++-----
 1 file changed, 10 insertions(+), 5 deletions(-)

Comments

Joe Hershberger May 3, 2016, 8:17 p.m. UTC | #1 
Hi Dan,

https://patchwork.ozlabs.org/patch/617696/ was applied to u-boot-net.git.

Thanks!
-Joe
diff mbox

Patch

diff --git a/drivers/net/zynq_gem.c b/drivers/net/zynq_gem.c
index aec8077..f9b22c4 100644
--- a/drivers/net/zynq_gem.c
+++ b/drivers/net/zynq_gem.c
@@ -179,6 +179,7 @@  struct zynq_gem_priv {
 	struct zynq_gem_regs *iobase;
 	phy_interface_t interface;
 	struct phy_device *phydev;
+	int phy_of_handle;
 	struct mii_dev *bus;
 };
 
@@ -352,6 +353,10 @@  static int zynq_phy_init(struct udevice *dev)
 	priv->phydev->supported = supported | ADVERTISED_Pause |
 				  ADVERTISED_Asym_Pause;
 	priv->phydev->advertising = priv->phydev->supported;
+
+	if (priv->phy_of_handle > 0)
+		priv->phydev->dev->of_offset = priv->phy_of_handle;
+
 	phy_config(priv->phydev);
 
 	return 0;
@@ -675,7 +680,6 @@  static int zynq_gem_ofdata_to_platdata(struct udevice *dev)
 {
 	struct eth_pdata *pdata = dev_get_platdata(dev);
 	struct zynq_gem_priv *priv = dev_get_priv(dev);
-	int offset = 0;
 	const char *phy_mode;
 
 	pdata->iobase = (phys_addr_t)dev_get_addr(dev);
@@ -684,10 +688,11 @@  static int zynq_gem_ofdata_to_platdata(struct udevice *dev)
 	priv->emio = 0;
 	priv->phyaddr = -1;
 
-	offset = fdtdec_lookup_phandle(gd->fdt_blob, dev->of_offset,
-				       "phy-handle");
-	if (offset > 0)
-		priv->phyaddr = fdtdec_get_int(gd->fdt_blob, offset, "reg", -1);
+	priv->phy_of_handle = fdtdec_lookup_phandle(gd->fdt_blob,
+					dev->of_offset, "phy-handle");
+	if (priv->phy_of_handle > 0)
+		priv->phyaddr = fdtdec_get_int(gd->fdt_blob,
+					priv->phy_of_handle, "reg", -1);
 
 	phy_mode = fdt_getprop(gd->fdt_blob, dev->of_offset, "phy-mode", NULL);
 	if (phy_mode)