@@ -122,22 +122,14 @@
};
mmcsd_default_mode: mmcsd_default {
mmcsd_default_cfg1 {
- /* MCCLK */
- pins = "GPIO8_B10";
- ste,output = <0>;
- };
- mmcsd_default_cfg2 {
- /* MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2 */
- pins = "GPIO10_C11", "GPIO15_A12",
- "GPIO16_C13", "GPIO23_D15";
- ste,output = <1>;
- };
- mmcsd_default_cfg3 {
- /* MCCMD, MCDAT3-0, MCMSFBCLK */
- pins = "GPIO9_A10", "GPIO11_B11",
- "GPIO12_A11", "GPIO13_C12",
- "GPIO14_B12", "GPIO24_C15";
- ste,input = <1>;
+ /*
+ * MCCLK, MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2
+ * MCCMD, MCDAT3-0, MCMSFBCLK
+ */
+ pins = "GPIO8_B10", "GPIO9_A10", "GPIO10_C11", "GPIO11_B11",
+ "GPIO12_A11", "GPIO13_C12", "GPIO14_B12", "GPIO15_A12",
+ "GPIO16_C13", "GPIO23_D15", "GPIO24_C15";
+ ste,output = <2>;
};
};
};
@@ -804,10 +796,21 @@
clock-names = "mclk", "apb_pclk";
interrupt-parent = <&vica>;
interrupts = <22>;
- max-frequency = <48000000>;
+ max-frequency = <400000>;
bus-width = <4>;
cap-mmc-highspeed;
cap-sd-highspeed;
+ full-pwr-cycle;
+ /*
+ * The STw4811 circuit used with the Nomadik strictly
+ * requires that all of these signal direction pins be
+ * routed and used for its 4-bit levelshifter.
+ */
+ st,sig-dir-dat0;
+ st,sig-dir-dat2;
+ st,sig-dir-dat31;
+ st,sig-dir-cmd;
+ st,sig-pin-fbclk;
pinctrl-names = "default";
pinctrl-0 = <&mmcsd_default_mux>, <&mmcsd_default_mode>;
vmmc-supply = <&vmmc_regulator>;
This is a note to let you know that I have just added a patch titled ARM: nomadik: fix up SD/MMC DT settings to the linux-4.2.y-queue branch of the 4.2.y-ckt extended stable tree which can be found at: http://kernel.ubuntu.com/git/ubuntu/linux.git/log/?h=linux-4.2.y-queue This patch is scheduled to be released in version 4.2.8-ckt5. If you, or anyone else, feels it should not be added to this tree, please reply to this email. For more information about the 4.2.y-ckt tree, see https://wiki.ubuntu.com/Kernel/Dev/ExtendedStable Thanks. -Kamal ---8<------------------------------------------------------------ From f8b4447806c2e1c39885ffb76e43ccb8493947b7 Mon Sep 17 00:00:00 2001 From: Linus Walleij <linus.walleij@linaro.org> Date: Mon, 1 Feb 2016 14:18:57 +0100 Subject: ARM: nomadik: fix up SD/MMC DT settings commit 418d5516568b3fdbc4e7b53677dd78aed8514565 upstream. The DTSI file for the Nomadik does not properly specify how the PL180 levelshifter is connected: the Nomadik actually needs all the five st,sig-dir-* flags set to properly control all lines out. Further this board supports full power cycling of the card, and since this variant has no hardware clock gating, it needs a ridiculously low frequency setting to keep up with the ever overflowing FIFO. The pin configuration set-up is a bit of a mystery, because of course these pins are a mix of inputs and outputs. However the reference implementation sets all pins to "output" with unspecified initial value, so let's do that here as well. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Kamal Mostafa <kamal@canonical.com> --- arch/arm/boot/dts/ste-nomadik-stn8815.dtsi | 37 ++++++++++++++++-------------- 1 file changed, 20 insertions(+), 17 deletions(-) -- 2.7.0