| Message ID | 1454294492-5369-2-git-send-email-ye.li@nxp.com |
|---|---|
| State | Changes Requested |
| Delegated to: | Stefano Babic |
| Headers | show |
Hi Ye, On 01/02/2016 03:41, Ye Li wrote: > Initial version for mx6sx SABREAUTO board support with features: > PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander. > > Signed-off-by: Ye Li <ye.li@nxp.com> > --- > Changes for v3: > - None > Changes for v2: > - None > > arch/arm/cpu/armv7/mx6/Kconfig | 6 + > board/freescale/mx6sxsabreauto/Kconfig | 12 + > board/freescale/mx6sxsabreauto/MAINTAINERS | 6 + > board/freescale/mx6sxsabreauto/Makefile | 6 + > board/freescale/mx6sxsabreauto/imximage.cfg | 136 ++++++ > board/freescale/mx6sxsabreauto/mx6sxsabreauto.c | 508 +++++++++++++++++++++++ > configs/mx6sxsabreauto_defconfig | 11 + > include/configs/mx6sxsabreauto.h | 212 ++++++++++ > 8 files changed, 897 insertions(+), 0 deletions(-) > create mode 100644 board/freescale/mx6sxsabreauto/Kconfig > create mode 100644 board/freescale/mx6sxsabreauto/MAINTAINERS > create mode 100644 board/freescale/mx6sxsabreauto/Makefile > create mode 100644 board/freescale/mx6sxsabreauto/imximage.cfg > create mode 100644 board/freescale/mx6sxsabreauto/mx6sxsabreauto.c > create mode 100644 configs/mx6sxsabreauto_defconfig > create mode 100644 include/configs/mx6sxsabreauto.h > > diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig > index 8489182..c72a150 100644 > --- a/arch/arm/cpu/armv7/mx6/Kconfig > +++ b/arch/arm/cpu/armv7/mx6/Kconfig > @@ -96,6 +96,11 @@ config TARGET_MX6SXSABRESD > select DM > select DM_THERMAL > > +config TARGET_MX6SXSABREAUTO > + bool "mx6sxsabreauto" > + select DM > + select DM_THERMAL > + > config TARGET_MX6UL_9X9_EVK > bool "mx6ul_9x9_evk" > select MX6UL > @@ -166,6 +171,7 @@ source "board/freescale/mx6qsabreauto/Kconfig" > source "board/freescale/mx6sabresd/Kconfig" > source "board/freescale/mx6slevk/Kconfig" > source "board/freescale/mx6sxsabresd/Kconfig" > +source "board/freescale/mx6sxsabreauto/Kconfig" > source "board/freescale/mx6ul_14x14_evk/Kconfig" > source "board/gateworks/gw_ventana/Kconfig" > source "board/kosagi/novena/Kconfig" > diff --git a/board/freescale/mx6sxsabreauto/Kconfig b/board/freescale/mx6sxsabreauto/Kconfig > new file mode 100644 > index 0000000..ae2ea02 > --- /dev/null > +++ b/board/freescale/mx6sxsabreauto/Kconfig > @@ -0,0 +1,12 @@ > +if TARGET_MX6SXSABREAUTO > + > +config SYS_BOARD > + default "mx6sxsabreauto" > + > +config SYS_VENDOR > + default "freescale" > + > +config SYS_CONFIG_NAME > + default "mx6sxsabreauto" > + > +endif > diff --git a/board/freescale/mx6sxsabreauto/MAINTAINERS b/board/freescale/mx6sxsabreauto/MAINTAINERS > new file mode 100644 > index 0000000..6f2ff44 > --- /dev/null > +++ b/board/freescale/mx6sxsabreauto/MAINTAINERS > @@ -0,0 +1,6 @@ > +MX6SXSABREAUTO BOARD > +M: Fabio Estevam <fabio.estevam@nxp.com> > +S: Maintained > +F: board/freescale/mx6sxsabreauto/ > +F: include/configs/mx6sxsabreauto.h > +F: configs/mx6sxsabreauto_defconfig > diff --git a/board/freescale/mx6sxsabreauto/Makefile b/board/freescale/mx6sxsabreauto/Makefile > new file mode 100644 > index 0000000..f0cd1ce > --- /dev/null > +++ b/board/freescale/mx6sxsabreauto/Makefile > @@ -0,0 +1,6 @@ > +# (C) Copyright 2014 Freescale Semiconductor, Inc. > +# > +# SPDX-License-Identifier: GPL-2.0+ > +# > + > +obj-y := mx6sxsabreauto.o > diff --git a/board/freescale/mx6sxsabreauto/imximage.cfg b/board/freescale/mx6sxsabreauto/imximage.cfg > new file mode 100644 > index 0000000..529e555 > --- /dev/null > +++ b/board/freescale/mx6sxsabreauto/imximage.cfg > @@ -0,0 +1,136 @@ > +/* > + * Copyright (C) 2014 Freescale Semiconductor, Inc. > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#define __ASSEMBLY__ > +#include <config.h> > + > +/* image version */ > + > +IMAGE_VERSION 2 > + > +/* > + * Boot Device : one of > + * spi/sd/nand/onenand, qspi/nor > + */ > + > +BOOT_FROM sd > + > +/* > + * Device Configuration Data (DCD) > + * > + * Each entry must have the format: > + * Addr-type Address Value > + * > + * where: > + * Addr-type register length (1,2 or 4 bytes) > + * Address absolute address of the register > + * value value to be stored in the register > + */ > + > +/* Enable all clocks */ > +DATA 4 0x020c4068 0xffffffff > +DATA 4 0x020c406c 0xffffffff > +DATA 4 0x020c4070 0xffffffff > +DATA 4 0x020c4074 0xffffffff > +DATA 4 0x020c4078 0xffffffff > +DATA 4 0x020c407c 0xffffffff > +DATA 4 0x020c4080 0xffffffff > +DATA 4 0x020c4084 0xffffffff > + > +/* IOMUX - DDR IO Type */ > +DATA 4 0x020e0618 0x000c0000 > +DATA 4 0x020e05fc 0x00000000 > + > +/* Clock */ > +DATA 4 0x020e032c 0x00000030 > + > +/* Address */ > +DATA 4 0x020e0300 0x00000030 > +DATA 4 0x020e02fc 0x00000030 > +DATA 4 0x020e05f4 0x00000030 > + > +/* Control */ > +DATA 4 0x020e0340 0x00000030 > + > +DATA 4 0x020e0320 0x00000000 > +DATA 4 0x020e0310 0x00000030 > +DATA 4 0x020e0314 0x00000030 > +DATA 4 0x020e0614 0x00000030 > + > +/* Data Strobe */ > +DATA 4 0x020e05f8 0x00020000 > +DATA 4 0x020e0330 0x00000030 > +DATA 4 0x020e0334 0x00000030 > +DATA 4 0x020e0338 0x00000030 > +DATA 4 0x020e033c 0x00000030 > + > +/* Data */ > +DATA 4 0x020e0608 0x00020000 > +DATA 4 0x020e060c 0x00000030 > +DATA 4 0x020e0610 0x00000030 > +DATA 4 0x020e061c 0x00000030 > +DATA 4 0x020e0620 0x00000030 > +DATA 4 0x020e02ec 0x00000030 > +DATA 4 0x020e02f0 0x00000030 > +DATA 4 0x020e02f4 0x00000030 > +DATA 4 0x020e02f8 0x00000030 > + > +/* Calibrations - ZQ */ > +DATA 4 0x021b0800 0xa1390003 > + > +/* Write leveling */ > +DATA 4 0x021b080c 0x002C003D > +DATA 4 0x021b0810 0x00110046 > + > +/* DQS Read Gate */ > +DATA 4 0x021b083c 0x4160016C > +DATA 4 0x021b0840 0x013C016C > + > +/* Read/Write Delay */ > +DATA 4 0x021b0848 0x46424446 > +DATA 4 0x021b0850 0x3A3C3C3A > + > +DATA 4 0x021b08c0 0x2492244A > + > +/* read data bit delay */ > +DATA 4 0x021b081c 0x33333333 > +DATA 4 0x021b0820 0x33333333 > +DATA 4 0x021b0824 0x33333333 > +DATA 4 0x021b0828 0x33333333 > + > +/* Complete calibration by forced measurement */ > +DATA 4 0x021b08b8 0x00000800 > + > +/* MMDC init - DDR3, 64-bit mode, only MMDC0 is initiated */ > +DATA 4 0x021b0004 0x0002002d > +DATA 4 0x021b0008 0x00333030 > +DATA 4 0x021b000c 0x676b52f3 > +DATA 4 0x021b0010 0xb66d8b63 > +DATA 4 0x021b0014 0x01ff00db > +DATA 4 0x021b0018 0x00011740 > +DATA 4 0x021b001c 0x00008000 > +DATA 4 0x021b002c 0x000026d2 > +DATA 4 0x021b0030 0x006b1023 > +DATA 4 0x021b0040 0x0000007f > +DATA 4 0x021b0000 0x85190000 > + > +/* Initialize MT41K256M16HA-125 - MR2 */ > +DATA 4 0x021b001c 0x04008032 > +/* MR3 */ > +DATA 4 0x021b001c 0x00008033 > +/* MR1 */ > +DATA 4 0x021b001c 0x00068031 > +/* MR0 */ > +DATA 4 0x021b001c 0x05208030 > +/* DDR device ZQ calibration */ > +DATA 4 0x021b001c 0x04008040 > + > +/* Final DDR setup, before operation start */ > +DATA 4 0x021b0020 0x00000800 > +DATA 4 0x021b0818 0x00022227 > +DATA 4 0x021b0004 0x0002556d > +DATA 4 0x021b0404 0x00011006 > +DATA 4 0x021b001c 0x00000000 > diff --git a/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c > new file mode 100644 > index 0000000..c9631d2 > --- /dev/null > +++ b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c > @@ -0,0 +1,508 @@ > +/* > + * Copyright (C) 2014 Freescale Semiconductor, Inc. > + * > + * Author: Ye Li <ye.li@nxp.com> > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#include <asm/arch/clock.h> > +#include <asm/arch/crm_regs.h> > +#include <asm/arch/iomux.h> > +#include <asm/arch/imx-regs.h> > +#include <asm/arch/mx6-pins.h> > +#include <asm/arch/sys_proto.h> > +#include <asm/gpio.h> > +#include <asm/imx-common/iomux-v3.h> > +#include <asm/imx-common/boot_mode.h> > +#include <asm/io.h> > +#include <asm/imx-common/mxc_i2c.h> > +#include <linux/sizes.h> > +#include <common.h> > +#include <fsl_esdhc.h> > +#include <mmc.h> > +#include <i2c.h> > +#include <miiphy.h> > +#include <netdev.h> > +#include <power/pmic.h> > +#include <power/pfuze100_pmic.h> > +#include "../common/pfuze.h" > +#include <usb.h> > +#include <usb/ehci-fsl.h> > +#include <pca953x.h> > + > +DECLARE_GLOBAL_DATA_PTR; > + > +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ > + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ > + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) > + > +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ > + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ > + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) > + > +#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ > + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ > + PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ > + PAD_CTL_ODE) > + > +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \ > + PAD_CTL_SPEED_HIGH | \ > + PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST) > + > +#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \ > + PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST) > + > +#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ > + PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST) > + > +#define I2C_PMIC 1 > + > +#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP) > +#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \ > + PAD_CTL_SRE_FAST) > +#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1) > + > +/*Define for building port exp gpio, pin starts from 0*/ > +#define PORTEXP_IO_NR(chip, pin) \ > + ((chip << 5) + pin) > + > +/*Get the chip addr from a ioexp gpio*/ > +#define PORTEXP_IO_TO_CHIP(gpio_nr) \ > + (gpio_nr >> 5) > + > +/*Get the pin number from a ioexp gpio*/ > +#define PORTEXP_IO_TO_PIN(gpio_nr) \ > + (gpio_nr & 0x1f) > + > +#define CPU_PER_RST_B PORTEXP_IO_NR(0x30, 4) > +#define STEER_ENET PORTEXP_IO_NR(0x32, 2) > + > +static int port_exp_direction_output(unsigned gpio, int value) > +{ > + int ret; > + > + i2c_set_bus_num(2); > + ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio)); > + if (ret) > + return ret; > + > + ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio), > + (1 << PORTEXP_IO_TO_PIN(gpio)), > + (PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio))); > + > + if (ret) > + return ret; > + > + ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio), > + (1 << PORTEXP_IO_TO_PIN(gpio)), > + (value << PORTEXP_IO_TO_PIN(gpio))); > + > + if (ret) > + return ret; > + > + return 0; > +} > + > +int dram_init(void) > +{ > + gd->ram_size = PHYS_SDRAM_SIZE; Why do not use get_ram_size ? > + > + return 0; > +} > + > +static iomux_v3_cfg_t const uart1_pads[] = { > + MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL), > + MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL), > +}; > + > +static iomux_v3_cfg_t const usdhc3_pads[] = { > + MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD3_DATA4__USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD3_DATA5__USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD3_DATA6__USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD3_DATA7__USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + > + /* CD pin */ > + MX6_PAD_USB_H_DATA__GPIO7_IO_10 | MUX_PAD_CTRL(NO_PAD_CTRL), > + > + /* RST_B, used for power reset cycle */ > + MX6_PAD_KEY_COL1__GPIO2_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL), > +}; > + > +static iomux_v3_cfg_t const usdhc4_pads[] = { > + MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), > + > + /* CD pin */ > + MX6_PAD_USB_H_STROBE__GPIO7_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL), > +}; > + > +static iomux_v3_cfg_t const fec2_pads[] = { > + MX6_PAD_ENET1_MDC__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_ENET1_MDIO__ENET2_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII2_RX_CTL__ENET2_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), > + MX6_PAD_RGMII2_RD0__ENET2_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), > + MX6_PAD_RGMII2_RD1__ENET2_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), > + MX6_PAD_RGMII2_RD2__ENET2_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), > + MX6_PAD_RGMII2_RD3__ENET2_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), > + MX6_PAD_RGMII2_RXC__ENET2_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), > + MX6_PAD_RGMII2_TX_CTL__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII2_TD0__ENET2_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII2_TD1__ENET2_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII2_TD2__ENET2_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII2_TD3__ENET2_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII2_TXC__ENET2_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), > +}; > + > +static void setup_iomux_uart(void) > +{ > + imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); > +} > + > +static int setup_fec(void) > +{ > + struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; > + > + /* Use 125MHz anatop loopback REF_CLK1 for ENET2 */ > + clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK, 0); > + > + return enable_fec_anatop_clock(1, ENET_125MHZ); > +} > + > +int board_eth_init(bd_t *bis) > +{ > + int ret; > + > + imx_iomux_v3_setup_multiple_pads(fec2_pads, ARRAY_SIZE(fec2_pads)); > + setup_fec(); > + > + ret = fecmxc_initialize_multi(bis, 1, > + CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE); > + if (ret) > + printf("FEC%d MXC: %s:failed\n", 1, __func__); > + > + return ret; > +} > + > +int board_phy_config(struct phy_device *phydev) > +{ > + /* > + * Enable 1.8V(SEL_1P5_1P8_POS_REG) on > + * Phy control debug reg 0 > + */ > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8); > + > + /* rgmii tx clock delay enable */ > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); > + > + if (phydev->drv->config) > + phydev->drv->config(phydev); > + > + return 0; > +} > + > +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) PC just makes line shorter, but it has no meaning. At least, change the name with something related to I2C or do not use the macro. I think it is more readable. > +/* I2C2 for PMIC */ > +struct i2c_pads_info i2c_pad_info2 = { > + .scl = { > + .i2c_mode = MX6_PAD_GPIO1_IO02__I2C2_SCL | PC, > + .gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO_2 | PC, > + .gp = IMX_GPIO_NR(1, 2), > + }, > + .sda = { > + .i2c_mode = MX6_PAD_GPIO1_IO03__I2C2_SDA | PC, > + .gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO_3 | PC, > + .gp = IMX_GPIO_NR(1, 3), > + }, > +}; > + > +/* I2C3 for IO Expander */ > +struct i2c_pads_info i2c_pad_info3 = { > + .scl = { > + .i2c_mode = MX6_PAD_KEY_COL4__I2C3_SCL | PC, > + .gpio_mode = MX6_PAD_KEY_COL4__GPIO2_IO_14 | PC, > + .gp = IMX_GPIO_NR(2, 14), > + }, > + .sda = { > + .i2c_mode = MX6_PAD_KEY_ROW4__I2C3_SDA | PC, > + .gpio_mode = MX6_PAD_KEY_ROW4__GPIO2_IO_19 | PC, > + .gp = IMX_GPIO_NR(2, 19), > + }, > +}; > + > +int power_init_board(void) > +{ > + struct pmic *p; > + > + p = pfuze_common_init(I2C_PMIC); > + if (!p) > + return -ENODEV; I have expected that PMIC is configured here. Which is the reason to have power_init_board ? It looks like an empty function. > + > + return 0; > +} > + > +#ifdef CONFIG_USB_EHCI_MX6 > +#define USB_OTHERREGS_OFFSET 0x800 > +#define UCTRL_PWR_POL (1 << 9) > + > +static iomux_v3_cfg_t const usb_otg_pads[] = { > + /* OGT1 */ > + MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), > + MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL), > + /* OTG2 */ > + MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL) > +}; > + > +static void setup_usb(void) > +{ > + imx_iomux_v3_setup_multiple_pads(usb_otg_pads, > + ARRAY_SIZE(usb_otg_pads)); > +} > + > +int board_usb_phy_mode(int port) > +{ > + if (port == 1) > + return USB_INIT_HOST; > + else > + return usb_phy_mode(port); > +} > + > +int board_ehci_hcd_init(int port) > +{ > + u32 *usbnc_usb_ctrl; > + > + if (port > 1) > + return -EINVAL; > + > + usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET + > + port * 4); > + > + /* Set Power polarity */ > + setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL); > + > + return 0; > +} > +#endif > + > +int board_early_init_f(void) > +{ > + setup_iomux_uart(); > + > + return 0; > +} > + > +static struct fsl_esdhc_cfg usdhc_cfg[3] = { > + {USDHC3_BASE_ADDR}, > + {USDHC4_BASE_ADDR}, > +}; > + > +#define USDHC3_CD_GPIO IMX_GPIO_NR(7, 10) > +#define USDHC3_RST_GPIO IMX_GPIO_NR(2, 11) > +#define USDHC4_CD_GPIO IMX_GPIO_NR(7, 11) > + > +int board_mmc_getcd(struct mmc *mmc) > +{ > + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; > + int ret = 0; > + > + switch (cfg->esdhc_base) { > + case USDHC3_BASE_ADDR: > + ret = !gpio_get_value(USDHC3_CD_GPIO); > + break; > + case USDHC4_BASE_ADDR: > + ret = !gpio_get_value(USDHC4_CD_GPIO); > + break; > + } > + > + return ret; > +} > + > +int board_mmc_init(bd_t *bis) > +{ > + int i, ret; > + > + /* > + * According to the board_mmc_init() the following map is done: > + * (U-boot device node) (Physical Port) > + * mmc0 USDHC3 > + * mmc1 USDHC4 > + */ > + for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { > + switch (i) { > + case 0: > + imx_iomux_v3_setup_multiple_pads( > + usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); > + gpio_direction_input(USDHC3_CD_GPIO); > + > + /* This starts a power cycle for UHS-I. Need to set steer to B0 to A*/ > + gpio_direction_output(USDHC3_RST_GPIO, 0); > + udelay(1000); /* need 1ms at least */ > + gpio_direction_output(USDHC3_RST_GPIO, 1); > + > + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); > + break; > + case 1: > + imx_iomux_v3_setup_multiple_pads( > + usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); > + gpio_direction_input(USDHC4_CD_GPIO); > + usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); > + break; > + default: > + printf("Warning: you configured more USDHC controllers" > + "(%d) than supported by the board\n", i + 1); > + return -EINVAL; > + } > + > + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); > + if (ret) { > + printf("Warning: failed to initialize mmc dev %d\n", i); > + return ret; > + } > + } > + > + return 0; > +} > + > +#ifdef CONFIG_FSL_QSPI > + > +#define QSPI_PAD_CTRL1 \ > + (PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \ > + PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm) > + > +static iomux_v3_cfg_t const quadspi_pads[] = { > + MX6_PAD_QSPI1A_SS0_B__QSPI1_A_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_QSPI1A_SCLK__QSPI1_A_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_QSPI1A_DATA0__QSPI1_A_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_QSPI1A_DATA1__QSPI1_A_DATA_1 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_QSPI1A_DATA2__QSPI1_A_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_QSPI1A_DATA3__QSPI1_A_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_QSPI1B_SS0_B__QSPI1_B_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_QSPI1B_SCLK__QSPI1_B_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_QSPI1B_DATA0__QSPI1_B_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_QSPI1B_DATA1__QSPI1_B_DATA_1 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_QSPI1B_DATA2__QSPI1_B_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > + MX6_PAD_QSPI1B_DATA3__QSPI1_B_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), > +}; > + > +int board_qspi_init(void) > +{ > + /* Set the iomux */ > + imx_iomux_v3_setup_multiple_pads(quadspi_pads, > + ARRAY_SIZE(quadspi_pads)); > + > + /* Set the clock */ > + enable_qspi_clk(0); > + > + return 0; > +} > +#endif > + > +#ifdef CONFIG_NAND_MXS > +iomux_v3_cfg_t gpmi_pads[] = { > + MX6_PAD_NAND_CLE__RAWNAND_CLE | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > + MX6_PAD_NAND_ALE__RAWNAND_ALE | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > + MX6_PAD_NAND_WP_B__RAWNAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > + MX6_PAD_NAND_READY_B__RAWNAND_READY_B | MUX_PAD_CTRL(GPMI_PAD_CTRL0), > + MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > + MX6_PAD_NAND_RE_B__RAWNAND_RE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > + MX6_PAD_NAND_WE_B__RAWNAND_WE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > + MX6_PAD_NAND_DATA00__RAWNAND_DATA00 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > + MX6_PAD_NAND_DATA01__RAWNAND_DATA01 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > + MX6_PAD_NAND_DATA02__RAWNAND_DATA02 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > + MX6_PAD_NAND_DATA03__RAWNAND_DATA03 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > + MX6_PAD_NAND_DATA04__RAWNAND_DATA04 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > + MX6_PAD_NAND_DATA05__RAWNAND_DATA05 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > + MX6_PAD_NAND_DATA06__RAWNAND_DATA06 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > + MX6_PAD_NAND_DATA07__RAWNAND_DATA07 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), > +}; > + > +static void setup_gpmi_nand(void) > +{ > + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; > + > + /* config gpmi nand iomux */ > + imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads)); > + > + setup_gpmi_io_clk((MXC_CCM_CS2CDR_QSPI2_CLK_PODF(0) | > + MXC_CCM_CS2CDR_QSPI2_CLK_PRED(3) | > + MXC_CCM_CS2CDR_QSPI2_CLK_SEL(3))); > + > + /* enable apbh clock gating */ > + setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK); > +} > +#endif > + > +int board_init(void) > +{ > + /* Address of boot parameters */ > + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; > + > +#ifdef CONFIG_SYS_I2C_MXC > + setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); > + setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3); > +#endif > + > + /* Reset CPU_PER_RST_B signal for enet phy and PCIE */ > + port_exp_direction_output(CPU_PER_RST_B, 0); Is this ok ? You have surrounded the I2C initialization with CONFIG_SYS_I2C_MXC, but port_exp_direction_output() is outside. What happens if CONFIG_SYS_I2C_MXC is not set ? Anyway, if you think that CONFIG_SYS_I2C_MXC must be set, you could drop the #ifdef. > + udelay(500); > + port_exp_direction_output(CPU_PER_RST_B, 1); > + > + /* Set steering signal to L for selecting B0 */ > + port_exp_direction_output(STEER_ENET, 0); > + > +#ifdef CONFIG_USB_EHCI_MX6 > + setup_usb(); > +#endif > + > +#ifdef CONFIG_FSL_QSPI > + board_qspi_init(); > +#endif > + > +#ifdef CONFIG_NAND_MXS > + setup_gpmi_nand(); > +#endif > + > + return 0; > +} > + > +#ifdef CONFIG_CMD_BMODE > +static const struct boot_mode board_boot_modes[] = { > + {"sda", MAKE_CFGVAL(0x42, 0x30, 0x00, 0x00)}, > + {"sdb", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)}, > + {"qspi1", MAKE_CFGVAL(0x10, 0x00, 0x00, 0x00)}, > + {"nand", MAKE_CFGVAL(0x82, 0x00, 0x00, 0x00)}, > + {NULL, 0}, > +}; > +#endif > + > +int board_late_init(void) > +{ > +#ifdef CONFIG_CMD_BMODE > + add_board_boot_modes(board_boot_modes); > +#endif > + > + return 0; > +} > + > +int checkboard(void) > +{ > + puts("Board: MX6SX SABRE AUTO\n"); > + > + return 0; > +} > diff --git a/configs/mx6sxsabreauto_defconfig b/configs/mx6sxsabreauto_defconfig > new file mode 100644 > index 0000000..d9e35df > --- /dev/null > +++ b/configs/mx6sxsabreauto_defconfig > @@ -0,0 +1,11 @@ > +CONFIG_ARM=y > +CONFIG_ARCH_MX6=y > +CONFIG_TARGET_MX6SXSABREAUTO=y > +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sxsabreauto/imximage.cfg,MX6SX" > +# CONFIG_CMD_IMLS is not set > +# CONFIG_CMD_FLASH is not set > +CONFIG_CMD_GPIO=y > +# CONFIG_CMD_SETEXPR is not set > +CONFIG_SPI_FLASH=y > +CONFIG_SPI_FLASH_BAR=y > +CONFIG_SPI_FLASH_STMICRO=y > diff --git a/include/configs/mx6sxsabreauto.h b/include/configs/mx6sxsabreauto.h > new file mode 100644 > index 0000000..2e739f9 > --- /dev/null > +++ b/include/configs/mx6sxsabreauto.h > @@ -0,0 +1,212 @@ > +/* > + * Copyright 2014 Freescale Semiconductor, Inc. > + * > + * Configuration settings for the Freescale i.MX6SX Sabreauto board. > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > + > +#ifndef __CONFIG_H > +#define __CONFIG_H > + > +#include "mx6_common.h" > + > + > +/* Size of malloc() pool */ > +#define CONFIG_SYS_MALLOC_LEN (3 * SZ_1M) > + > +#define CONFIG_BOARD_EARLY_INIT_F > +#define CONFIG_BOARD_LATE_INIT > + > +#define CONFIG_MXC_UART > +#define CONFIG_MXC_UART_BASE UART1_BASE > + > +#define CONFIG_EXTRA_ENV_SETTINGS \ > + "script=boot.scr\0" \ > + "image=zImage\0" \ > + "console=ttymxc0\0" \ > + "fdt_high=0xffffffff\0" \ > + "initrd_high=0xffffffff\0" \ > + "fdt_file=imx6sx-sabreauto.dtb\0" \ > + "fdt_addr=0x88000000\0" \ > + "boot_fdt=try\0" \ > + "ip_dyn=yes\0" \ > + "mmcdev=0\0" \ > + "mmcpart=1\0" \ > + "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \ > + "mmcargs=setenv bootargs console=${console},${baudrate} " \ > + "root=${mmcroot}\0" \ > + "loadbootscript=" \ > + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ > + "bootscript=echo Running bootscript from mmc ...; " \ > + "source\0" \ > + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ > + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ > + "mmcboot=echo Booting from mmc ...; " \ > + "run mmcargs; " \ > + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ > + "if run loadfdt; then " \ > + "bootz ${loadaddr} - ${fdt_addr}; " \ > + "else " \ > + "if test ${boot_fdt} = try; then " \ > + "bootz; " \ > + "else " \ > + "echo WARN: Cannot load the DT; " \ > + "fi; " \ > + "fi; " \ > + "else " \ > + "bootz; " \ > + "fi;\0" \ > + "netargs=setenv bootargs console=${console},${baudrate} " \ > + "root=/dev/nfs " \ > + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ > + "netboot=echo Booting from net ...; " \ > + "run netargs; " \ > + "if test ${ip_dyn} = yes; then " \ > + "setenv get_cmd dhcp; " \ > + "else " \ > + "setenv get_cmd tftp; " \ > + "fi; " \ > + "${get_cmd} ${image}; " \ > + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ > + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ > + "bootz ${loadaddr} - ${fdt_addr}; " \ > + "else " \ > + "if test ${boot_fdt} = try; then " \ > + "bootz; " \ > + "else " \ > + "echo WARN: Cannot load the DT; " \ > + "fi; " \ > + "fi; " \ > + "else " \ > + "bootz; " \ > + "fi;\0" > + > +#define CONFIG_BOOTCOMMAND \ > + "mmc dev ${mmcdev};" \ > + "mmc dev ${mmcdev}; if mmc rescan; then " \ > + "if run loadbootscript; then " \ > + "run bootscript; " \ > + "else " \ > + "if run loadimage; then " \ > + "run mmcboot; " \ > + "else run netboot; " \ > + "fi; " \ > + "fi; " \ > + "else run netboot; fi" > + No comment, but I am gently asking if you have thought to switch to distro environment. It makes board behaving in the same way. > +/* Miscellaneous configurable options */ > +#define CONFIG_SYS_MEMTEST_START 0x80000000 > +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x10000) > + > +#define CONFIG_STACKSIZE SZ_128K > + > +/* Physical Memory Map */ > +#define CONFIG_NR_DRAM_BANKS 1 > +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR > +#define PHYS_SDRAM_SIZE SZ_2G > + > +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM > +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR > +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE > + > +#define CONFIG_SYS_INIT_SP_OFFSET \ > + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) > +#define CONFIG_SYS_INIT_SP_ADDR \ > + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) > + > +/* MMC Configuration */ > +#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC3_BASE_ADDR > + > +/* I2C Configs */ > +#define CONFIG_CMD_I2C > +#define CONFIG_SYS_I2C > +#define CONFIG_SYS_I2C_MXC > +#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ > +#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ > +#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ > +#define CONFIG_SYS_I2C_SPEED 100000 > + > +/* PMIC */ > +#define CONFIG_POWER > +#define CONFIG_POWER_I2C > +#define CONFIG_POWER_PFUZE100 > +#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 > + > +/* NAND flash command */ > +#define CONFIG_CMD_NAND > +#define CONFIG_CMD_NAND_TRIMFFS > + > +/* NAND stuff */ > +#define CONFIG_NAND_MXS > +#define CONFIG_SYS_MAX_NAND_DEVICE 1 > +#define CONFIG_SYS_NAND_BASE 0x40000000 > +#define CONFIG_SYS_NAND_5_ADDR_CYCLE > +#define CONFIG_SYS_NAND_ONFI_DETECTION > + > +/* DMA stuff, needed for GPMI/MXS NAND support */ > +#define CONFIG_APBH_DMA > +#define CONFIG_APBH_DMA_BURST > +#define CONFIG_APBH_DMA_BURST8 > + > +/* Network */ > +#define CONFIG_CMD_PING > +#define CONFIG_CMD_DHCP > +#define CONFIG_CMD_MII > + > +#define CONFIG_FEC_MXC > +#define CONFIG_MII > + > +#define IMX_FEC_BASE ENET2_BASE_ADDR > +#define CONFIG_FEC_MXC_PHYADDR 0x0 > + > +#define CONFIG_FEC_XCV_TYPE RGMII > +#define CONFIG_ETHPRIME "FEC" > + > +#define CONFIG_PHYLIB > +#define CONFIG_PHY_ATHEROS > + > + > +#define CONFIG_CMD_USB > +#ifdef CONFIG_CMD_USB > +#define CONFIG_USB_EHCI > +#define CONFIG_USB_EHCI_MX6 > +#define CONFIG_USB_STORAGE > +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET > +#define CONFIG_USB_HOST_ETHER > +#define CONFIG_USB_ETHER_ASIX > +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) > +#define CONFIG_MXC_USB_FLAGS 0 > +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 > +#endif > + > +#define CONFIG_IMX_THERMAL > + > +#define CONFIG_CMD_TIME > + > +#define CONFIG_FSL_QSPI > +#ifdef CONFIG_FSL_QSPI > +#define CONFIG_CMD_SF > +#define CONFIG_SYS_FSL_QSPI_AHB > +#define CONFIG_SF_DEFAULT_BUS 0 > +#define CONFIG_SF_DEFAULT_CS 0 > +#define CONFIG_SF_DEFAULT_SPEED 40000000 > +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 > +#define FSL_QSPI_FLASH_SIZE SZ_32M > +#define FSL_QSPI_FLASH_NUM 2 > +#endif > + > +#define CONFIG_ENV_OFFSET (8 * SZ_64K) > +#define CONFIG_ENV_SIZE SZ_8K > +#define CONFIG_ENV_IS_IN_MMC > + > +#define CONFIG_SYS_FSL_USDHC_NUM 2 > +#if defined(CONFIG_ENV_IS_IN_MMC) > +#define CONFIG_SYS_MMC_ENV_DEV 0 /*USDHC3*/ > +#endif > + > +#define CONFIG_PCA953X > +#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x30, 8}, {0x32, 8}, {0x34, 8} } > + > +#endif /* __CONFIG_H */ > Best regards, Stefano Babic
diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig index 8489182..c72a150 100644 --- a/arch/arm/cpu/armv7/mx6/Kconfig +++ b/arch/arm/cpu/armv7/mx6/Kconfig @@ -96,6 +96,11 @@ config TARGET_MX6SXSABRESD select DM select DM_THERMAL +config TARGET_MX6SXSABREAUTO + bool "mx6sxsabreauto" + select DM + select DM_THERMAL + config TARGET_MX6UL_9X9_EVK bool "mx6ul_9x9_evk" select MX6UL @@ -166,6 +171,7 @@ source "board/freescale/mx6qsabreauto/Kconfig" source "board/freescale/mx6sabresd/Kconfig" source "board/freescale/mx6slevk/Kconfig" source "board/freescale/mx6sxsabresd/Kconfig" +source "board/freescale/mx6sxsabreauto/Kconfig" source "board/freescale/mx6ul_14x14_evk/Kconfig" source "board/gateworks/gw_ventana/Kconfig" source "board/kosagi/novena/Kconfig" diff --git a/board/freescale/mx6sxsabreauto/Kconfig b/board/freescale/mx6sxsabreauto/Kconfig new file mode 100644 index 0000000..ae2ea02 --- /dev/null +++ b/board/freescale/mx6sxsabreauto/Kconfig @@ -0,0 +1,12 @@ +if TARGET_MX6SXSABREAUTO + +config SYS_BOARD + default "mx6sxsabreauto" + +config SYS_VENDOR + default "freescale" + +config SYS_CONFIG_NAME + default "mx6sxsabreauto" + +endif diff --git a/board/freescale/mx6sxsabreauto/MAINTAINERS b/board/freescale/mx6sxsabreauto/MAINTAINERS new file mode 100644 index 0000000..6f2ff44 --- /dev/null +++ b/board/freescale/mx6sxsabreauto/MAINTAINERS @@ -0,0 +1,6 @@ +MX6SXSABREAUTO BOARD +M: Fabio Estevam <fabio.estevam@nxp.com> +S: Maintained +F: board/freescale/mx6sxsabreauto/ +F: include/configs/mx6sxsabreauto.h +F: configs/mx6sxsabreauto_defconfig diff --git a/board/freescale/mx6sxsabreauto/Makefile b/board/freescale/mx6sxsabreauto/Makefile new file mode 100644 index 0000000..f0cd1ce --- /dev/null +++ b/board/freescale/mx6sxsabreauto/Makefile @@ -0,0 +1,6 @@ +# (C) Copyright 2014 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := mx6sxsabreauto.o diff --git a/board/freescale/mx6sxsabreauto/imximage.cfg b/board/freescale/mx6sxsabreauto/imximage.cfg new file mode 100644 index 0000000..529e555 --- /dev/null +++ b/board/freescale/mx6sxsabreauto/imximage.cfg @@ -0,0 +1,136 @@ +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#define __ASSEMBLY__ +#include <config.h> + +/* image version */ + +IMAGE_VERSION 2 + +/* + * Boot Device : one of + * spi/sd/nand/onenand, qspi/nor + */ + +BOOT_FROM sd + +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ + +/* Enable all clocks */ +DATA 4 0x020c4068 0xffffffff +DATA 4 0x020c406c 0xffffffff +DATA 4 0x020c4070 0xffffffff +DATA 4 0x020c4074 0xffffffff +DATA 4 0x020c4078 0xffffffff +DATA 4 0x020c407c 0xffffffff +DATA 4 0x020c4080 0xffffffff +DATA 4 0x020c4084 0xffffffff + +/* IOMUX - DDR IO Type */ +DATA 4 0x020e0618 0x000c0000 +DATA 4 0x020e05fc 0x00000000 + +/* Clock */ +DATA 4 0x020e032c 0x00000030 + +/* Address */ +DATA 4 0x020e0300 0x00000030 +DATA 4 0x020e02fc 0x00000030 +DATA 4 0x020e05f4 0x00000030 + +/* Control */ +DATA 4 0x020e0340 0x00000030 + +DATA 4 0x020e0320 0x00000000 +DATA 4 0x020e0310 0x00000030 +DATA 4 0x020e0314 0x00000030 +DATA 4 0x020e0614 0x00000030 + +/* Data Strobe */ +DATA 4 0x020e05f8 0x00020000 +DATA 4 0x020e0330 0x00000030 +DATA 4 0x020e0334 0x00000030 +DATA 4 0x020e0338 0x00000030 +DATA 4 0x020e033c 0x00000030 + +/* Data */ +DATA 4 0x020e0608 0x00020000 +DATA 4 0x020e060c 0x00000030 +DATA 4 0x020e0610 0x00000030 +DATA 4 0x020e061c 0x00000030 +DATA 4 0x020e0620 0x00000030 +DATA 4 0x020e02ec 0x00000030 +DATA 4 0x020e02f0 0x00000030 +DATA 4 0x020e02f4 0x00000030 +DATA 4 0x020e02f8 0x00000030 + +/* Calibrations - ZQ */ +DATA 4 0x021b0800 0xa1390003 + +/* Write leveling */ +DATA 4 0x021b080c 0x002C003D +DATA 4 0x021b0810 0x00110046 + +/* DQS Read Gate */ +DATA 4 0x021b083c 0x4160016C +DATA 4 0x021b0840 0x013C016C + +/* Read/Write Delay */ +DATA 4 0x021b0848 0x46424446 +DATA 4 0x021b0850 0x3A3C3C3A + +DATA 4 0x021b08c0 0x2492244A + +/* read data bit delay */ +DATA 4 0x021b081c 0x33333333 +DATA 4 0x021b0820 0x33333333 +DATA 4 0x021b0824 0x33333333 +DATA 4 0x021b0828 0x33333333 + +/* Complete calibration by forced measurement */ +DATA 4 0x021b08b8 0x00000800 + +/* MMDC init - DDR3, 64-bit mode, only MMDC0 is initiated */ +DATA 4 0x021b0004 0x0002002d +DATA 4 0x021b0008 0x00333030 +DATA 4 0x021b000c 0x676b52f3 +DATA 4 0x021b0010 0xb66d8b63 +DATA 4 0x021b0014 0x01ff00db +DATA 4 0x021b0018 0x00011740 +DATA 4 0x021b001c 0x00008000 +DATA 4 0x021b002c 0x000026d2 +DATA 4 0x021b0030 0x006b1023 +DATA 4 0x021b0040 0x0000007f +DATA 4 0x021b0000 0x85190000 + +/* Initialize MT41K256M16HA-125 - MR2 */ +DATA 4 0x021b001c 0x04008032 +/* MR3 */ +DATA 4 0x021b001c 0x00008033 +/* MR1 */ +DATA 4 0x021b001c 0x00068031 +/* MR0 */ +DATA 4 0x021b001c 0x05208030 +/* DDR device ZQ calibration */ +DATA 4 0x021b001c 0x04008040 + +/* Final DDR setup, before operation start */ +DATA 4 0x021b0020 0x00000800 +DATA 4 0x021b0818 0x00022227 +DATA 4 0x021b0004 0x0002556d +DATA 4 0x021b0404 0x00011006 +DATA 4 0x021b001c 0x00000000 diff --git a/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c new file mode 100644 index 0000000..c9631d2 --- /dev/null +++ b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c @@ -0,0 +1,508 @@ +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * + * Author: Ye Li <ye.li@nxp.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <asm/arch/clock.h> +#include <asm/arch/crm_regs.h> +#include <asm/arch/iomux.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/mx6-pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/gpio.h> +#include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/boot_mode.h> +#include <asm/io.h> +#include <asm/imx-common/mxc_i2c.h> +#include <linux/sizes.h> +#include <common.h> +#include <fsl_esdhc.h> +#include <mmc.h> +#include <i2c.h> +#include <miiphy.h> +#include <netdev.h> +#include <power/pmic.h> +#include <power/pfuze100_pmic.h> +#include "../common/pfuze.h" +#include <usb.h> +#include <usb/ehci-fsl.h> +#include <pca953x.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE) + +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \ + PAD_CTL_SPEED_HIGH | \ + PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST) + +#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST) + +#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST) + +#define I2C_PMIC 1 + +#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP) +#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \ + PAD_CTL_SRE_FAST) +#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1) + +/*Define for building port exp gpio, pin starts from 0*/ +#define PORTEXP_IO_NR(chip, pin) \ + ((chip << 5) + pin) + +/*Get the chip addr from a ioexp gpio*/ +#define PORTEXP_IO_TO_CHIP(gpio_nr) \ + (gpio_nr >> 5) + +/*Get the pin number from a ioexp gpio*/ +#define PORTEXP_IO_TO_PIN(gpio_nr) \ + (gpio_nr & 0x1f) + +#define CPU_PER_RST_B PORTEXP_IO_NR(0x30, 4) +#define STEER_ENET PORTEXP_IO_NR(0x32, 2) + +static int port_exp_direction_output(unsigned gpio, int value) +{ + int ret; + + i2c_set_bus_num(2); + ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio)); + if (ret) + return ret; + + ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio), + (1 << PORTEXP_IO_TO_PIN(gpio)), + (PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio))); + + if (ret) + return ret; + + ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio), + (1 << PORTEXP_IO_TO_PIN(gpio)), + (value << PORTEXP_IO_TO_PIN(gpio))); + + if (ret) + return ret; + + return 0; +} + +int dram_init(void) +{ + gd->ram_size = PHYS_SDRAM_SIZE; + + return 0; +} + +static iomux_v3_cfg_t const uart1_pads[] = { + MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static iomux_v3_cfg_t const usdhc3_pads[] = { + MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA4__USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA5__USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA6__USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA7__USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + + /* CD pin */ + MX6_PAD_USB_H_DATA__GPIO7_IO_10 | MUX_PAD_CTRL(NO_PAD_CTRL), + + /* RST_B, used for power reset cycle */ + MX6_PAD_KEY_COL1__GPIO2_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static iomux_v3_cfg_t const usdhc4_pads[] = { + MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + + /* CD pin */ + MX6_PAD_USB_H_STROBE__GPIO7_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static iomux_v3_cfg_t const fec2_pads[] = { + MX6_PAD_ENET1_MDC__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_ENET1_MDIO__ENET2_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII2_RX_CTL__ENET2_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6_PAD_RGMII2_RD0__ENET2_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6_PAD_RGMII2_RD1__ENET2_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6_PAD_RGMII2_RD2__ENET2_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6_PAD_RGMII2_RD3__ENET2_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6_PAD_RGMII2_RXC__ENET2_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), + MX6_PAD_RGMII2_TX_CTL__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII2_TD0__ENET2_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII2_TD1__ENET2_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII2_TD2__ENET2_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII2_TD3__ENET2_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII2_TXC__ENET2_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), +}; + +static void setup_iomux_uart(void) +{ + imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); +} + +static int setup_fec(void) +{ + struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; + + /* Use 125MHz anatop loopback REF_CLK1 for ENET2 */ + clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK, 0); + + return enable_fec_anatop_clock(1, ENET_125MHZ); +} + +int board_eth_init(bd_t *bis) +{ + int ret; + + imx_iomux_v3_setup_multiple_pads(fec2_pads, ARRAY_SIZE(fec2_pads)); + setup_fec(); + + ret = fecmxc_initialize_multi(bis, 1, + CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE); + if (ret) + printf("FEC%d MXC: %s:failed\n", 1, __func__); + + return ret; +} + +int board_phy_config(struct phy_device *phydev) +{ + /* + * Enable 1.8V(SEL_1P5_1P8_POS_REG) on + * Phy control debug reg 0 + */ + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8); + + /* rgmii tx clock delay enable */ + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); + + if (phydev->drv->config) + phydev->drv->config(phydev); + + return 0; +} + +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) +/* I2C2 for PMIC */ +struct i2c_pads_info i2c_pad_info2 = { + .scl = { + .i2c_mode = MX6_PAD_GPIO1_IO02__I2C2_SCL | PC, + .gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO_2 | PC, + .gp = IMX_GPIO_NR(1, 2), + }, + .sda = { + .i2c_mode = MX6_PAD_GPIO1_IO03__I2C2_SDA | PC, + .gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO_3 | PC, + .gp = IMX_GPIO_NR(1, 3), + }, +}; + +/* I2C3 for IO Expander */ +struct i2c_pads_info i2c_pad_info3 = { + .scl = { + .i2c_mode = MX6_PAD_KEY_COL4__I2C3_SCL | PC, + .gpio_mode = MX6_PAD_KEY_COL4__GPIO2_IO_14 | PC, + .gp = IMX_GPIO_NR(2, 14), + }, + .sda = { + .i2c_mode = MX6_PAD_KEY_ROW4__I2C3_SDA | PC, + .gpio_mode = MX6_PAD_KEY_ROW4__GPIO2_IO_19 | PC, + .gp = IMX_GPIO_NR(2, 19), + }, +}; + +int power_init_board(void) +{ + struct pmic *p; + + p = pfuze_common_init(I2C_PMIC); + if (!p) + return -ENODEV; + + return 0; +} + +#ifdef CONFIG_USB_EHCI_MX6 +#define USB_OTHERREGS_OFFSET 0x800 +#define UCTRL_PWR_POL (1 << 9) + +static iomux_v3_cfg_t const usb_otg_pads[] = { + /* OGT1 */ + MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL), + /* OTG2 */ + MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL) +}; + +static void setup_usb(void) +{ + imx_iomux_v3_setup_multiple_pads(usb_otg_pads, + ARRAY_SIZE(usb_otg_pads)); +} + +int board_usb_phy_mode(int port) +{ + if (port == 1) + return USB_INIT_HOST; + else + return usb_phy_mode(port); +} + +int board_ehci_hcd_init(int port) +{ + u32 *usbnc_usb_ctrl; + + if (port > 1) + return -EINVAL; + + usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET + + port * 4); + + /* Set Power polarity */ + setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL); + + return 0; +} +#endif + +int board_early_init_f(void) +{ + setup_iomux_uart(); + + return 0; +} + +static struct fsl_esdhc_cfg usdhc_cfg[3] = { + {USDHC3_BASE_ADDR}, + {USDHC4_BASE_ADDR}, +}; + +#define USDHC3_CD_GPIO IMX_GPIO_NR(7, 10) +#define USDHC3_RST_GPIO IMX_GPIO_NR(2, 11) +#define USDHC4_CD_GPIO IMX_GPIO_NR(7, 11) + +int board_mmc_getcd(struct mmc *mmc) +{ + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; + int ret = 0; + + switch (cfg->esdhc_base) { + case USDHC3_BASE_ADDR: + ret = !gpio_get_value(USDHC3_CD_GPIO); + break; + case USDHC4_BASE_ADDR: + ret = !gpio_get_value(USDHC4_CD_GPIO); + break; + } + + return ret; +} + +int board_mmc_init(bd_t *bis) +{ + int i, ret; + + /* + * According to the board_mmc_init() the following map is done: + * (U-boot device node) (Physical Port) + * mmc0 USDHC3 + * mmc1 USDHC4 + */ + for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { + switch (i) { + case 0: + imx_iomux_v3_setup_multiple_pads( + usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); + gpio_direction_input(USDHC3_CD_GPIO); + + /* This starts a power cycle for UHS-I. Need to set steer to B0 to A*/ + gpio_direction_output(USDHC3_RST_GPIO, 0); + udelay(1000); /* need 1ms at least */ + gpio_direction_output(USDHC3_RST_GPIO, 1); + + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); + break; + case 1: + imx_iomux_v3_setup_multiple_pads( + usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); + gpio_direction_input(USDHC4_CD_GPIO); + usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); + break; + default: + printf("Warning: you configured more USDHC controllers" + "(%d) than supported by the board\n", i + 1); + return -EINVAL; + } + + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); + if (ret) { + printf("Warning: failed to initialize mmc dev %d\n", i); + return ret; + } + } + + return 0; +} + +#ifdef CONFIG_FSL_QSPI + +#define QSPI_PAD_CTRL1 \ + (PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \ + PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm) + +static iomux_v3_cfg_t const quadspi_pads[] = { + MX6_PAD_QSPI1A_SS0_B__QSPI1_A_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_QSPI1A_SCLK__QSPI1_A_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_QSPI1A_DATA0__QSPI1_A_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_QSPI1A_DATA1__QSPI1_A_DATA_1 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_QSPI1A_DATA2__QSPI1_A_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_QSPI1A_DATA3__QSPI1_A_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_QSPI1B_SS0_B__QSPI1_B_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_QSPI1B_SCLK__QSPI1_B_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_QSPI1B_DATA0__QSPI1_B_DATA_0 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_QSPI1B_DATA1__QSPI1_B_DATA_1 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_QSPI1B_DATA2__QSPI1_B_DATA_2 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), + MX6_PAD_QSPI1B_DATA3__QSPI1_B_DATA_3 | MUX_PAD_CTRL(QSPI_PAD_CTRL1), +}; + +int board_qspi_init(void) +{ + /* Set the iomux */ + imx_iomux_v3_setup_multiple_pads(quadspi_pads, + ARRAY_SIZE(quadspi_pads)); + + /* Set the clock */ + enable_qspi_clk(0); + + return 0; +} +#endif + +#ifdef CONFIG_NAND_MXS +iomux_v3_cfg_t gpmi_pads[] = { + MX6_PAD_NAND_CLE__RAWNAND_CLE | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6_PAD_NAND_ALE__RAWNAND_ALE | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6_PAD_NAND_WP_B__RAWNAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6_PAD_NAND_READY_B__RAWNAND_READY_B | MUX_PAD_CTRL(GPMI_PAD_CTRL0), + MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6_PAD_NAND_RE_B__RAWNAND_RE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6_PAD_NAND_WE_B__RAWNAND_WE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6_PAD_NAND_DATA00__RAWNAND_DATA00 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6_PAD_NAND_DATA01__RAWNAND_DATA01 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6_PAD_NAND_DATA02__RAWNAND_DATA02 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6_PAD_NAND_DATA03__RAWNAND_DATA03 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6_PAD_NAND_DATA04__RAWNAND_DATA04 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6_PAD_NAND_DATA05__RAWNAND_DATA05 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6_PAD_NAND_DATA06__RAWNAND_DATA06 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), + MX6_PAD_NAND_DATA07__RAWNAND_DATA07 | MUX_PAD_CTRL(GPMI_PAD_CTRL2), +}; + +static void setup_gpmi_nand(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + /* config gpmi nand iomux */ + imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads)); + + setup_gpmi_io_clk((MXC_CCM_CS2CDR_QSPI2_CLK_PODF(0) | + MXC_CCM_CS2CDR_QSPI2_CLK_PRED(3) | + MXC_CCM_CS2CDR_QSPI2_CLK_SEL(3))); + + /* enable apbh clock gating */ + setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK); +} +#endif + +int board_init(void) +{ + /* Address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + +#ifdef CONFIG_SYS_I2C_MXC + setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); + setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3); +#endif + + /* Reset CPU_PER_RST_B signal for enet phy and PCIE */ + port_exp_direction_output(CPU_PER_RST_B, 0); + udelay(500); + port_exp_direction_output(CPU_PER_RST_B, 1); + + /* Set steering signal to L for selecting B0 */ + port_exp_direction_output(STEER_ENET, 0); + +#ifdef CONFIG_USB_EHCI_MX6 + setup_usb(); +#endif + +#ifdef CONFIG_FSL_QSPI + board_qspi_init(); +#endif + +#ifdef CONFIG_NAND_MXS + setup_gpmi_nand(); +#endif + + return 0; +} + +#ifdef CONFIG_CMD_BMODE +static const struct boot_mode board_boot_modes[] = { + {"sda", MAKE_CFGVAL(0x42, 0x30, 0x00, 0x00)}, + {"sdb", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)}, + {"qspi1", MAKE_CFGVAL(0x10, 0x00, 0x00, 0x00)}, + {"nand", MAKE_CFGVAL(0x82, 0x00, 0x00, 0x00)}, + {NULL, 0}, +}; +#endif + +int board_late_init(void) +{ +#ifdef CONFIG_CMD_BMODE + add_board_boot_modes(board_boot_modes); +#endif + + return 0; +} + +int checkboard(void) +{ + puts("Board: MX6SX SABRE AUTO\n"); + + return 0; +} diff --git a/configs/mx6sxsabreauto_defconfig b/configs/mx6sxsabreauto_defconfig new file mode 100644 index 0000000..d9e35df --- /dev/null +++ b/configs/mx6sxsabreauto_defconfig @@ -0,0 +1,11 @@ +CONFIG_ARM=y +CONFIG_ARCH_MX6=y +CONFIG_TARGET_MX6SXSABREAUTO=y +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sxsabreauto/imximage.cfg,MX6SX" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_GPIO=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_BAR=y +CONFIG_SPI_FLASH_STMICRO=y diff --git a/include/configs/mx6sxsabreauto.h b/include/configs/mx6sxsabreauto.h new file mode 100644 index 0000000..2e739f9 --- /dev/null +++ b/include/configs/mx6sxsabreauto.h @@ -0,0 +1,212 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * Configuration settings for the Freescale i.MX6SX Sabreauto board. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include "mx6_common.h" + + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (3 * SZ_1M) + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_LATE_INIT + +#define CONFIG_MXC_UART +#define CONFIG_MXC_UART_BASE UART1_BASE + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "script=boot.scr\0" \ + "image=zImage\0" \ + "console=ttymxc0\0" \ + "fdt_high=0xffffffff\0" \ + "initrd_high=0xffffffff\0" \ + "fdt_file=imx6sx-sabreauto.dtb\0" \ + "fdt_addr=0x88000000\0" \ + "boot_fdt=try\0" \ + "ip_dyn=yes\0" \ + "mmcdev=0\0" \ + "mmcpart=1\0" \ + "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \ + "mmcargs=setenv bootargs console=${console},${baudrate} " \ + "root=${mmcroot}\0" \ + "loadbootscript=" \ + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if run loadfdt; then " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootz; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootz; " \ + "fi;\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${image}; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootz; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootz; " \ + "fi;\0" + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev};" \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loadimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else run netboot; fi" + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_MEMTEST_START 0x80000000 +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x10000) + +#define CONFIG_STACKSIZE SZ_128K + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR +#define PHYS_SDRAM_SIZE SZ_2G + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* MMC Configuration */ +#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC3_BASE_ADDR + +/* I2C Configs */ +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ +#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ +#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ +#define CONFIG_SYS_I2C_SPEED 100000 + +/* PMIC */ +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_PFUZE100 +#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 + +/* NAND flash command */ +#define CONFIG_CMD_NAND +#define CONFIG_CMD_NAND_TRIMFFS + +/* NAND stuff */ +#define CONFIG_NAND_MXS +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE 0x40000000 +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_ONFI_DETECTION + +/* DMA stuff, needed for GPMI/MXS NAND support */ +#define CONFIG_APBH_DMA +#define CONFIG_APBH_DMA_BURST +#define CONFIG_APBH_DMA_BURST8 + +/* Network */ +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII + +#define CONFIG_FEC_MXC +#define CONFIG_MII + +#define IMX_FEC_BASE ENET2_BASE_ADDR +#define CONFIG_FEC_MXC_PHYADDR 0x0 + +#define CONFIG_FEC_XCV_TYPE RGMII +#define CONFIG_ETHPRIME "FEC" + +#define CONFIG_PHYLIB +#define CONFIG_PHY_ATHEROS + + +#define CONFIG_CMD_USB +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_MX6 +#define CONFIG_USB_STORAGE +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_USB_HOST_ETHER +#define CONFIG_USB_ETHER_ASIX +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) +#define CONFIG_MXC_USB_FLAGS 0 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 +#endif + +#define CONFIG_IMX_THERMAL + +#define CONFIG_CMD_TIME + +#define CONFIG_FSL_QSPI +#ifdef CONFIG_FSL_QSPI +#define CONFIG_CMD_SF +#define CONFIG_SYS_FSL_QSPI_AHB +#define CONFIG_SF_DEFAULT_BUS 0 +#define CONFIG_SF_DEFAULT_CS 0 +#define CONFIG_SF_DEFAULT_SPEED 40000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#define FSL_QSPI_FLASH_SIZE SZ_32M +#define FSL_QSPI_FLASH_NUM 2 +#endif + +#define CONFIG_ENV_OFFSET (8 * SZ_64K) +#define CONFIG_ENV_SIZE SZ_8K +#define CONFIG_ENV_IS_IN_MMC + +#define CONFIG_SYS_FSL_USDHC_NUM 2 +#if defined(CONFIG_ENV_IS_IN_MMC) +#define CONFIG_SYS_MMC_ENV_DEV 0 /*USDHC3*/ +#endif + +#define CONFIG_PCA953X +#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x30, 8}, {0x32, 8}, {0x34, 8} } + +#endif /* __CONFIG_H */
Initial version for mx6sx SABREAUTO board support with features: PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander. Signed-off-by: Ye Li <ye.li@nxp.com> --- Changes for v3: - None Changes for v2: - None arch/arm/cpu/armv7/mx6/Kconfig | 6 + board/freescale/mx6sxsabreauto/Kconfig | 12 + board/freescale/mx6sxsabreauto/MAINTAINERS | 6 + board/freescale/mx6sxsabreauto/Makefile | 6 + board/freescale/mx6sxsabreauto/imximage.cfg | 136 ++++++ board/freescale/mx6sxsabreauto/mx6sxsabreauto.c | 508 +++++++++++++++++++++++ configs/mx6sxsabreauto_defconfig | 11 + include/configs/mx6sxsabreauto.h | 212 ++++++++++ 8 files changed, 897 insertions(+), 0 deletions(-) create mode 100644 board/freescale/mx6sxsabreauto/Kconfig create mode 100644 board/freescale/mx6sxsabreauto/MAINTAINERS create mode 100644 board/freescale/mx6sxsabreauto/Makefile create mode 100644 board/freescale/mx6sxsabreauto/imximage.cfg create mode 100644 board/freescale/mx6sxsabreauto/mx6sxsabreauto.c create mode 100644 configs/mx6sxsabreauto_defconfig create mode 100644 include/configs/mx6sxsabreauto.h