new file mode 100644
@@ -0,0 +1,118 @@
+MAX77620 Power management IC from Maxim Semiconductor.
+
+Required properties:
+-------------------
+- compatible: Must be one of
+ "maxim,max77620"
+ "maxim,max20024".
+- reg: I2C device address.
+
+Optional properties:
+-------------------
+- interrupts: the interrupt on the parent the controller is
+ connected to
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: is <2> and their usage is compliant to the 2 cells
+ variant of <../interrupt-controller/interrupts.txt>
+ IRQ numbers for different interrupt source of MAX77620
+ are defined at dt-bindings/mfd/max77620.h.
+
+Optional subnodes and their properties:
+=======================================
+
+Flexible power sequence configurations:
+--------------------------------------
+The PMIC has multiple control mode:
+ Normal mode also called as active mode on which all step-down
+ regulators, all linear regulators, GPIOs, and the 32kHz
+ oscillator are in normal active mode.
+ sleep mode: Regulators/GPIOs/clock can go on OFF state based on
+ their configurations.
+ Global Low power mode (GLPM): In this mode, step-down regulators, linear
+ regulators, and the 32kHz oscillator are in low-power modes.
+
+ Different modes of regulators/clock/GPIOs are controlled by the their
+FPS configurations. There is different configuration registers for each of
+these resources. Typical configurations per resource are:
+ FPS source: Attach the resource to required FPS source. When
+ resources are attached to one of FPS source then
+ resournce can be enable/disable when related FPS
+ source gets the control signal for ON and OFF.
+ Power on slot: Slot number on which resource is ON once FPS source
+ get ON signal.
+ Power down slot Slot number on which resource is OFF once FPS source
+ get OFF signal.
+
+There is three FPS source for resources called FPS0, FPS1 and FPS2. All
+resources need to attached to one of these FPS. It can alsoi be set
+FPS source to NONE, and on this case, it is completely controlled by
+the register control rather than external input control to PMIC.
+
+The configuration parameters of FPS is provided through subnode "fps"
+and their child for FPS specific.
+The node name for FPS child are defined as "fps0", "fps1", and "fps2" for
+the FPS0, FPS1 and FPS2 respectively.
+
+There is need for different FPS configuration parameters based on system
+state like when system state changed from active to suspend or active to
+power off (shutdown).
+
+Optinal properties:
+-------------------
+-maxim,fps-control: u32, FPS control source like external control input
+ to PMIC i.e. EN0, EN1 or software (SW). The macros
+ are defined on dt-bindings/mfd/max77620.h for
+ different control source.
+ FPS_CONTROL_SRC_EN0 for PMIC external input EN0.
+ FPS_CONTROL_SRC_EN1 for PMIC external input EN1.
+ FPS_CONTROL_SRC_SW for software control.
+
+-maxim,shutdown-fps-time-period-us: u32, FPS time period in microseconds
+ when system enters to shutdown state.
+-maxim,suspend-fps-time-period-us: u32, FPS time period in microseconds
+ when system enters to suspend state.
+
+-maxim,enable-sleep: Boolean, enable sleep state of PMIC
+ when the FPS control input become active.
+-maxim,enable-global-lpm: Boolean, enable Global Low Power Mode (GLPM)
+ of PMIC when the FPS control input become
+ active.
+
+Here supported time periods by device in microseconds are as follows:
+MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds.
+MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds.
+
+For different sub modules like GPIO, pincontrol, regulator, power, please refer
+respected device-tree binding document on respective directories.
+
+Example:
+--------
+#include <dt-bindings/mfd/max77620.h>
+
+max77620@3c {
+ compatible = "maxim,max77620";
+ reg = <0x3c>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <0 86 IRQ_TYPE_NONE>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ fps {
+ fps0 {
+ maxim,shutdown-fps-time-period-us = <1280>;
+ maxim,fps-control = <FPS_CONTROL_SRC_EN1>;
+ };
+
+ fps1 {
+ maxim,shutdown-fps-time-period-us = <1280>;
+ maxim,fps-control = <FPS_CONTROL_SRC_EN0>;
+ };
+
+ fps2 {
+ maxim,shutdown-fps-time-period-us = <1280>;
+ maxim,fps-control = <FPS_CONTROL_SRC_SW>;
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,35 @@
+/*
+ * This header provides macros for MAXIM MAX77620 device bindings.
+ *
+ * Copyright (c) 2016, NVIDIA Corporation.
+ * Author: Laxman Dewangan <ldewangan@nvidia.com>
+ */
+
+#ifndef _DT_BINDINGS_MFD_MAX77620_H
+#define _DT_BINDINGS_MFD_MAX77620_H
+
+/* MAX77620 interrupts */
+#define MAX77620_IRQ_TOP_GLBL 0 /* Low-Battery */
+#define MAX77620_IRQ_TOP_SD 1 /* SD power fail */
+#define MAX77620_IRQ_TOP_LDO 2 /* LDO power fail */
+#define MAX77620_IRQ_TOP_GPIO 3 /* GPIO internal int to MAX77620 */
+#define MAX77620_IRQ_TOP_RTC 4 /* RTC */
+#define MAX77620_IRQ_TOP_32K 5 /* 32kHz oscillator */
+#define MAX77620_IRQ_TOP_ONOFF 6 /* ON/OFF oscillator */
+#define MAX77620_IRQ_LBT_MBATLOW 7 /* Thermal alarm status, > 120C */
+#define MAX77620_IRQ_LBT_TJALRM1 8 /* Thermal alarm status, > 120C */
+#define MAX77620_IRQ_LBT_TJALRM2 9 /* Thermal alarm status, > 140C */
+
+/* FPS control inputs */
+#define FPS_CONTROL_SRC_EN0 0
+#define FPS_CONTROL_SRC_EN1 1
+#define FPS_CONTROL_SRC_SW 2
+
+/* FPS source */
+#define FPS_SRC_0 0
+#define FPS_SRC_1 1
+#define FPS_SRC_2 2
+#define FPS_SRC_NONE 3
+#define FPS_SRC_DEF 4
+
+#endif