Patchwork Continuing UCC UART woes

On 06/24/2010 06:54 AM, Gary Thomas wrote:
> I thought I had this working, but it seems to only work for UCC3.
> Sadly, I can't get it to work on UCC4/UCC5/UCC8 at all.
>
> Starting with UCC4, I have:
> /* ttyQE0 (UCC4) */
> serial_qe0: serial@3200 {
> device_type = "serial";
> compatible = "ucc_uart";
> cell-index = <4>;
> reg = <0x3200 0x200>;
> interrupts = <35>;
> interrupt-parent = <&qeic>;
> port-number = <0>;
> rx-clock-name = "brg9";
> tx-clock-name = "brg10";
> soft-uart;
> };
>
> With this setup, I can receive characters from the device, but
> no characters ever go out. Same behaviour as before - the output
> descriptors get filled, but no action seems to be taken, no interrupts,
> etc. Except randomly there will be output! For example, if I
> connect to the port with minicom, what I type is received by /dev/ttyQE2.
> On some rare occasions, what I type is also echoed back, but when
> this happens, it's only the first couple of characters, then nothing.
>
> I verified that the CMXUCR registers are being set per the DTS
> as well as the BRG registers. They all look correct:
>
> ucc_set_qe_mux_rxtx - CMX: 0x000a0000
>
> root@ppc_target:~ stty </dev/ttyQE0 38400
> qe_setbrg - BRG: fddfd660 = 0x000106b6, CLK = 132000000, RATE = 9600,
> MULTIPLIER = 16
> qe_setbrg - BRG: fddfd664 = 0x000106b5, CLK = 132000000, RATE = 9600,
> MULTIPLIER = 1
> qe_setbrg - BRG: fddfd660 = 0x000101aa, CLK = 132000000, RATE = 38400,
> MULTIPLIER = 16
> qe_setbrg - BRG: fddfd664 = 0x00011ada, CLK = 132000000, RATE = 38400,
> MULTIPLIER = 1
>
> I've also tried this on UCC5 & UCC8 which show the identical
> behaviour - input works, output does not. I've tried running
> with only a single soft UART (UCC4) as well as having all three
> configured. No changes seen.
>
> At this point, I'm using the stock driver from 2.6.33.3
>
> One thing I noticed is that the firmware patch seems quite old.
> I got the firmware package from http://opensource.freescale.com/firmware/
> We were also told (by FreeScale) to look at
> https://www.freescale.com/webapp/Download?colCode=QERAMPKG
>
> Looking at these two packages, it's unclear that they match. Certainly
> the dates are very different:
>
> [gthomas@hermes 8358]$ ls -l fsl_qe_ucode QERAMPKG
> fsl_qe_ucode:
> total 16
> -rw-rw-r-- 1 gthomas gthomas 5940 2007-12-10 14:39
> fsl_qe_ucode_uart_8360_21.bin
> -rw-r--r-- 1 gthomas gthomas 7892 2007-11-30 10:14 license.txt
>
> QERAMPKG:
> total 972
> -rw-rw-r-- 1 gthomas gthomas 132915 2009-04-07 14:04
> SlowProtocols_8323rev11.c
> -rw-rw-r-- 1 gthomas gthomas 455446 2009-09-16 15:44
> Soft_UART_Microcode_Rel_0_1_2.pdf
> -rw-rw-r-- 1 gthomas gthomas 29379 2009-09-16 15:49
> Soft_UART_mpc8360_r2.0.h
> -rw-rw-r-- 1 gthomas gthomas 29379 2009-09-16 15:14
> Soft_UART_mpc8360_r2.1.h
> -rw-rw-r-- 1 gthomas gthomas 29379 2009-09-16 15:14
> Soft_UART_mpc8568_r1.1.h
> -rw-rw-r-- 1 gthomas gthomas 105457 2009-09-16 16:00 SWUART_8360rev20.c
> -rw-rw-r-- 1 gthomas gthomas 34689 2009-09-16 15:32 SWUART_8360rev20.srx
> -rw-rw-r-- 1 gthomas gthomas 105318 2009-09-16 15:59 SWUART_8360rev21.c
> -rw-rw-r-- 1 gthomas gthomas 34689 2009-09-16 15:14 SWUART_8360rev21.srx
>
> Any ideas what I'm doing wrong?

BTW, I tried converting the  Soft_UART_mpc8360_r2.1.h file
to the firmware format.  I had to fiddle with the conversion
program a bit because the firmware has version 0.1.2, but I
ended up with a new firmware file.  Here's the change I made:

$ diff -u make_qe_firmware.py*


No change in behaviour :-(