Message ID | 1451934663-68925-1-git-send-email-computersforpeace@gmail.com |
---|---|
State | Superseded |
Headers | show |
Hi Brian, On Mon, 4 Jan 2016 11:11:03 -0800 Brian Norris <computersforpeace@gmail.com> wrote: > Commits such as commit 853f1c58c4b2 ("mtd: nand: omap2: show parent > device structure in sysfs") attempt to rely on the core MTD code to set > the MTD name based on the parent device. However, nand_base tries to set > a different default name according to the flash name (e.g., extracted > from the ONFI parameter page), which means NAND drivers will never make > use of the MTD defaults. This is not the intention of commit > 853f1c58c4b2. > > This results in problems when trying to use the cmdline partition > parser, since the MTD name is different than expected. Let's fix this by > providing a default NAND name, where possible. > > Note that this is not really a great default name in the long run, since > this means that if there are multiple MTDs attached to the same > controller device, they will have the same name. But that is an existing > issue and requires future work on a better controller vs. flash chip > abstraction to fix properly. Yep, and IMHO, the chip numbering currently in use in most NAND controller drivers is not the best solution either. We should somehow find a way to describe the mtd id using something like: mtd-id: <nand-controller-id>@<cs-line> nand-controller-id: <nand-controller-ip-name>-<ip-address> Anyway, let's discuss that after the nand-chip <-> nand-controller separation rework. > > Reported-by: Heiko Schocher <hs@denx.de> > Signed-off-by: Brian Norris <computersforpeace@gmail.com> > Cc: Heiko Schocher <hs@denx.de> > Cc: Frans Klaver <fransklaver@gmail.com> > --- > This patch is needed in additon to commit 472b444eef93 ("mtd: fix cmdlinepart > parser, early naming for auto-filled MTD") to fix Heiko's reported problem. At > this point, I'm not sure if this should be targeted toward late 4.4 or for 4.5. > It's a 4.4 regresssion, but a very small one. And I'm not sure if this will > have wide enough impact that it should be given a longer time to be reviewed > and tested. We can always send it to -stable later, if it's really needed. > > drivers/mtd/nand/nand_base.c | 3 +++ > 1 file changed, 3 insertions(+) > > diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c > index ece544efccc3..9f169566fba4 100644 > --- a/drivers/mtd/nand/nand_base.c > +++ b/drivers/mtd/nand/nand_base.c > @@ -3826,6 +3826,9 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd, > if (!type) > type = nand_flash_ids; > > + if (!mtd->name && mtd->dev.parent) > + mtd->name = dev_name(mtd->dev.parent); > + Just nitpicking, but I think this would be better placed in nand_set_defaults() or in nand_scan_ident() before nand_get_flash_type() call. Anyway, Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> > for (; type->name != NULL; type++) { > if (is_full_id_nand(type)) { > if (find_full_id_nand(mtd, chip, type, id_data, &busw)) Best Regards, Boris
Hello Brian, Am 04.01.2016 um 20:11 schrieb Brian Norris: > Commits such as commit 853f1c58c4b2 ("mtd: nand: omap2: show parent > device structure in sysfs") attempt to rely on the core MTD code to set > the MTD name based on the parent device. However, nand_base tries to set > a different default name according to the flash name (e.g., extracted > from the ONFI parameter page), which means NAND drivers will never make > use of the MTD defaults. This is not the intention of commit > 853f1c58c4b2. > > This results in problems when trying to use the cmdline partition > parser, since the MTD name is different than expected. Let's fix this by > providing a default NAND name, where possible. > > Note that this is not really a great default name in the long run, since > this means that if there are multiple MTDs attached to the same > controller device, they will have the same name. But that is an existing > issue and requires future work on a better controller vs. flash chip > abstraction to fix properly. > > Reported-by: Heiko Schocher <hs@denx.de> > Signed-off-by: Brian Norris <computersforpeace@gmail.com> > Cc: Heiko Schocher <hs@denx.de> > Cc: Frans Klaver <fransklaver@gmail.com> > --- > This patch is needed in additon to commit 472b444eef93 ("mtd: fix cmdlinepart > parser, early naming for auto-filled MTD") to fix Heiko's reported problem. At > this point, I'm not sure if this should be targeted toward late 4.4 or for 4.5. > It's a 4.4 regresssion, but a very small one. And I'm not sure if this will > have wide enough impact that it should be given a longer time to be reviewed > and tested. We can always send it to -stable later, if it's really needed. Ok... but I wonder if nobody have the same problems as I ... > drivers/mtd/nand/nand_base.c | 3 +++ > 1 file changed, 3 insertions(+) Thanks! works for me, so: Tested-by: Heiko Schocher <hs@denx.de> bye, Heiko > > diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c > index ece544efccc3..9f169566fba4 100644 > --- a/drivers/mtd/nand/nand_base.c > +++ b/drivers/mtd/nand/nand_base.c > @@ -3826,6 +3826,9 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd, > if (!type) > type = nand_flash_ids; > > + if (!mtd->name && mtd->dev.parent) > + mtd->name = dev_name(mtd->dev.parent); > + > for (; type->name != NULL; type++) { > if (is_full_id_nand(type)) { > if (find_full_id_nand(mtd, chip, type, id_data, &busw)) >
Hi Brian, On Mon, 2016-01-04 at 11:11 -0800, Brian Norris wrote: > This patch is needed in additon to commit 472b444eef93 ("mtd: fix > cmdlinepart parser, early naming for auto-filled MTD") to fix Heiko's > reported problem. At this point, I'm not sure if this should be > targeted toward late 4.4 or for 4.5. It's a 4.4 regresssion, but a > very small one. And I'm not sure if this will have wide enough > impact that it should be given a longer time to be reviewed and > tested. We can always send it to -stable later, if it's really > needed. I have boards that will not boot 4.4 without these two patches, so I hope to see it go in to 4.4.1 (I guess it is too late for 4.4). Regards, Stefan
Hi Boris, On Mon, Jan 04, 2016 at 09:31:02PM +0100, Boris Brezillon wrote: > On Mon, 4 Jan 2016 11:11:03 -0800 > Brian Norris <computersforpeace@gmail.com> wrote: > > > Commits such as commit 853f1c58c4b2 ("mtd: nand: omap2: show parent > > device structure in sysfs") attempt to rely on the core MTD code to set > > the MTD name based on the parent device. However, nand_base tries to set > > a different default name according to the flash name (e.g., extracted > > from the ONFI parameter page), which means NAND drivers will never make > > use of the MTD defaults. This is not the intention of commit > > 853f1c58c4b2. > > > > This results in problems when trying to use the cmdline partition > > parser, since the MTD name is different than expected. Let's fix this by > > providing a default NAND name, where possible. > > > > Note that this is not really a great default name in the long run, since > > this means that if there are multiple MTDs attached to the same > > controller device, they will have the same name. But that is an existing > > issue and requires future work on a better controller vs. flash chip > > abstraction to fix properly. > > Yep, and IMHO, the chip numbering currently in use in most NAND > controller drivers is not the best solution either. We should somehow > find a way to describe the mtd id using something like: > > mtd-id: <nand-controller-id>@<cs-line> > nand-controller-id: <nand-controller-ip-name>-<ip-address> Maybe dots ('.') instead of '@'? But otherwise, seems somewhat reasonable. Maybe this could just be something like: dev_name(mtd->dev.parent) + "." + chip_select > Anyway, let's discuss that after the nand-chip <-> nand-controller > separation rework. Sure. > > Reported-by: Heiko Schocher <hs@denx.de> > > Signed-off-by: Brian Norris <computersforpeace@gmail.com> > > Cc: Heiko Schocher <hs@denx.de> > > Cc: Frans Klaver <fransklaver@gmail.com> > > --- > > This patch is needed in additon to commit 472b444eef93 ("mtd: fix cmdlinepart > > parser, early naming for auto-filled MTD") to fix Heiko's reported problem. At > > this point, I'm not sure if this should be targeted toward late 4.4 or for 4.5. > > It's a 4.4 regresssion, but a very small one. And I'm not sure if this will > > have wide enough impact that it should be given a longer time to be reviewed > > and tested. We can always send it to -stable later, if it's really needed. > > > > drivers/mtd/nand/nand_base.c | 3 +++ > > 1 file changed, 3 insertions(+) > > > > diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c > > index ece544efccc3..9f169566fba4 100644 > > --- a/drivers/mtd/nand/nand_base.c > > +++ b/drivers/mtd/nand/nand_base.c > > @@ -3826,6 +3826,9 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd, > > if (!type) > > type = nand_flash_ids; > > > > + if (!mtd->name && mtd->dev.parent) > > + mtd->name = dev_name(mtd->dev.parent); > > + > > Just nitpicking, but I think this would be better placed in > nand_set_defaults() or in nand_scan_ident() before nand_get_flash_type() > call. Hmm, nand_set_defaults() would probably be better. I'll resend this and defer it to 4.5 (and 4.4.x). > Anyway, > > Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Thanks, Brian
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index ece544efccc3..9f169566fba4 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -3826,6 +3826,9 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd, if (!type) type = nand_flash_ids; + if (!mtd->name && mtd->dev.parent) + mtd->name = dev_name(mtd->dev.parent); + for (; type->name != NULL; type++) { if (is_full_id_nand(type)) { if (find_full_id_nand(mtd, chip, type, id_data, &busw))
Commits such as commit 853f1c58c4b2 ("mtd: nand: omap2: show parent device structure in sysfs") attempt to rely on the core MTD code to set the MTD name based on the parent device. However, nand_base tries to set a different default name according to the flash name (e.g., extracted from the ONFI parameter page), which means NAND drivers will never make use of the MTD defaults. This is not the intention of commit 853f1c58c4b2. This results in problems when trying to use the cmdline partition parser, since the MTD name is different than expected. Let's fix this by providing a default NAND name, where possible. Note that this is not really a great default name in the long run, since this means that if there are multiple MTDs attached to the same controller device, they will have the same name. But that is an existing issue and requires future work on a better controller vs. flash chip abstraction to fix properly. Reported-by: Heiko Schocher <hs@denx.de> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: Heiko Schocher <hs@denx.de> Cc: Frans Klaver <fransklaver@gmail.com> --- This patch is needed in additon to commit 472b444eef93 ("mtd: fix cmdlinepart parser, early naming for auto-filled MTD") to fix Heiko's reported problem. At this point, I'm not sure if this should be targeted toward late 4.4 or for 4.5. It's a 4.4 regresssion, but a very small one. And I'm not sure if this will have wide enough impact that it should be given a longer time to be reviewed and tested. We can always send it to -stable later, if it's really needed. drivers/mtd/nand/nand_base.c | 3 +++ 1 file changed, 3 insertions(+)