gpio: pl061: detail IRQ trigger handling
diff mbox

Message ID 1442492485-5879-1-git-send-email-linus.walleij@linaro.org
State New
Headers show

Commit Message

Linus Walleij Sept. 17, 2015, 12:21 p.m. UTC
I couldn't follow this code flow. Make it dirt simple to figure
out what is going on and get proper debug prints. Warn if we
set up an IRQ without any trigger. Should make no semantic
difference.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 drivers/gpio/gpio-pl061.c | 55 ++++++++++++++++++++++++++++++++++++++++-------
 1 file changed, 47 insertions(+), 8 deletions(-)

Patch
diff mbox

diff --git a/drivers/gpio/gpio-pl061.c b/drivers/gpio/gpio-pl061.c
index 04756130437f..3868d5b32156 100644
--- a/drivers/gpio/gpio-pl061.c
+++ b/drivers/gpio/gpio-pl061.c
@@ -158,24 +158,63 @@  static int pl061_irq_type(struct irq_data *d, unsigned trigger)
 	gpiois = readb(chip->base + GPIOIS);
 	gpioibe = readb(chip->base + GPIOIBE);
 
+	if ((trigger & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) &&
+	    (trigger & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)))
+	{
+		dev_err(gc->dev,
+			"trying to configure line %d for both level and edge "
+			"detection, choose one!\n",
+			offset);
+		return -EINVAL;
+	}
+
 	if (trigger & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) {
+		bool polarity = trigger & IRQ_TYPE_LEVEL_HIGH;
+
+		/* Disable edge detection */
+		gpioibe &= ~bit;
+		/* Enable level detection */
 		gpiois |= bit;
-		if (trigger & IRQ_TYPE_LEVEL_HIGH)
+		/* Select polarity */
+		if (polarity)
 			gpioiev |= bit;
 		else
 			gpioiev &= ~bit;
-	} else
-		gpiois &= ~bit;
 
-	if ((trigger & IRQ_TYPE_EDGE_BOTH) == IRQ_TYPE_EDGE_BOTH)
-		/* Setting this makes GPIOEV be ignored */
+		dev_dbg(gc->dev, "line %d: IRQ on %s level\n",
+			offset,
+			polarity ? "HIGH" : "LOW");
+	} else if ((trigger & IRQ_TYPE_EDGE_BOTH) == IRQ_TYPE_EDGE_BOTH) {
+		/* Disable level detection */
+		gpiois &= ~bit;
+		/* Select both edges, setting this makes GPIOEV be ignored */
 		gpioibe |= bit;
-	else {
+
+		dev_dbg(gc->dev, "line %d: IRQ on both edges\n", offset);
+	} else if ((trigger & IRQ_TYPE_EDGE_RISING) ||
+		   (trigger & IRQ_TYPE_EDGE_FALLING)) {
+		bool rising = trigger & IRQ_TYPE_EDGE_RISING;
+
+		/* Disable level detection */
+		gpiois &= ~bit;
+		/* Clear detection on both edges */
 		gpioibe &= ~bit;
-		if (trigger & IRQ_TYPE_EDGE_RISING)
+		/* Select edge */
+		if (rising)
 			gpioiev |= bit;
-		else if (trigger & IRQ_TYPE_EDGE_FALLING)
+		else
 			gpioiev &= ~bit;
+
+		dev_dbg(gc->dev, "line %d: IRQ on %s edge\n",
+			offset,
+			rising ? "RISING" : "FALLING");
+	} else {
+		/* No trigger: disable everything */
+		gpiois &= ~bit;
+		gpioibe &= ~bit;
+		gpioiev &= ~bit;
+		dev_warn(gc->dev, "no trigger selected for line %d\n",
+			 offset);
 	}
 
 	writeb(gpiois, chip->base + GPIOIS);