@@ -30,7 +30,7 @@
#define NETNEXT_VERSION "08"
/* Information for net */
-#define NET_VERSION "1"
+#define NET_VERSION "2"
#define DRIVER_VERSION "v1." NETNEXT_VERSION "." NET_VERSION
#define DRIVER_AUTHOR "Realtek linux nic maintainers <nic_swsd@realtek.com>"
@@ -148,6 +148,7 @@
#define OCP_EEE_ABLE 0xa5c4
#define OCP_EEE_ADV 0xa5d0
#define OCP_EEE_LPABLE 0xa5d2
+#define OCP_PHY_STATE 0xa708 /* nway state for 8153 */
#define OCP_ADC_CFG 0xbc06
/* SRAM Register */
@@ -432,6 +433,10 @@
/* OCP_DOWN_SPEED */
#define EN_10M_BGOFF 0x0080
+/* OCP_PHY_STATE */
+#define TXDIS_STATE 0x01
+#define ABD_STATE 0x02
+
/* OCP_ADC_CFG */
#define CKADSEL_L 0x0100
#define ADC_EN 0x0080
@@ -609,6 +614,7 @@ struct r8152 {
void (*unload)(struct r8152 *);
int (*eee_get)(struct r8152 *, struct ethtool_eee *);
int (*eee_set)(struct r8152 *, struct ethtool_eee *);
+ bool (*in_nway)(struct r8152 *);
} rtl_ops;
int intr_interval;
@@ -2946,6 +2952,32 @@ static void rtl8153_down(struct r8152 *tp)
r8153_enable_aldps(tp);
}
+static bool rtl8152_in_nway(struct r8152 *tp)
+{
+ u16 nway_state;
+
+ ocp_write_word(tp, MCU_TYPE_PLA, PLA_OCP_GPHY_BASE, 0x2000);
+ tp->ocp_base = 0x2000;
+ ocp_write_byte(tp, MCU_TYPE_PLA, 0xb014, 0x4c); /* phy state */
+ nway_state = ocp_read_word(tp, MCU_TYPE_PLA, 0xb01a);
+
+ /* bit 15: TXDIS_STATE, bit 14: ABD_STATE */
+ if (nway_state & 0xc000)
+ return false;
+ else
+ return true;
+}
+
+static bool rtl8153_in_nway(struct r8152 *tp)
+{
+ u16 phy_state = ocp_reg_read(tp, OCP_PHY_STATE) & 0xff;
+
+ if (phy_state == TXDIS_STATE || phy_state == ABD_STATE)
+ return false;
+ else
+ return true;
+}
+
static void set_carrier(struct r8152 *tp)
{
struct net_device *netdev = tp->netdev;
@@ -3410,6 +3442,27 @@ static int rtl8152_post_reset(struct usb_interface *intf)
return 0;
}
+static bool delay_autosuspend(struct r8152 *tp)
+{
+ bool sw_linking = !!netif_carrier_ok(tp->netdev);
+ bool hw_linking = !!(rtl8152_get_speed(tp) & LINK_STATUS);
+
+ /* This means a linking change occurs and the driver doesn't detect it,
+ * yet. If the driver has disabled tx/rx and hw is linking on, the
+ * device wouldn't wake up by receiving any packet.
+ */
+ if (work_busy(&tp->schedule.work) || sw_linking != hw_linking)
+ return true;
+
+ /* If the linking down is occurred by nway, the device may miss the
+ * linking change event. And it wouldn't wake when linking on.
+ */
+ if (!sw_linking && tp->rtl_ops.in_nway(tp))
+ return true;
+ else
+ return false;
+}
+
static int rtl8152_suspend(struct usb_interface *intf, pm_message_t message)
{
struct r8152 *tp = usb_get_intfdata(intf);
@@ -3419,7 +3472,7 @@ static int rtl8152_suspend(struct usb_interface *intf, pm_message_t message)
mutex_lock(&tp->control);
if (PMSG_IS_AUTO(message)) {
- if (netif_running(netdev) && work_busy(&tp->schedule.work)) {
+ if (netif_running(netdev) && delay_autosuspend(tp)) {
ret = -EBUSY;
goto out1;
}
@@ -4049,6 +4102,7 @@ static int rtl_ops_init(struct r8152 *tp)
ops->unload = rtl8152_unload;
ops->eee_get = r8152_get_eee;
ops->eee_set = r8152_set_eee;
+ ops->in_nway = rtl8152_in_nway;
break;
case RTL_VER_03:
@@ -4063,6 +4117,7 @@ static int rtl_ops_init(struct r8152 *tp)
ops->unload = rtl8153_unload;
ops->eee_get = r8153_get_eee;
ops->eee_set = r8153_set_eee;
+ ops->in_nway = rtl8153_in_nway;
break;
default:
Fix the runtime suspend issues result from the linking change. Case 1: a) link down occurs. b) driver disable tx/rx. c) autosuspend occurs. d) hw linking up. e) device suspends without enabling tx/rx. f) couldn't wake up when receiving packets. Case 2: a) Nway results in linking down. b) autosuspend occurs. c) device suspends. d) device may not wake up when linking up. Signed-off-by: Hayes Wang <hayeswang@realtek.com> --- drivers/net/usb/r8152.c | 59 +++++++++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 57 insertions(+), 2 deletions(-)