[v2,8/8] pinctrl: freescale: imx: imx7d iomuxc-lpsr devicetree bindings
diff mbox

Message ID 1441147753-13239-8-git-send-email-aalonso@freescale.com
State New
Headers show

Commit Message

Adrian Alonso Sept. 1, 2015, 10:49 p.m. UTC
Add iomuxc-lpsr devicetree bindings documentation
Provide documentation context as well an example on
pheriperals that could use pad from either iomuxc controller
supported by iMX7D SoC

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
---
Changes for V2: New patch on imx7d iomuxc-lpsr patch series

 .../bindings/pinctrl/fsl,imx7d-pinctrl.txt         | 43 ++++++++++++++++++++++
 1 file changed, 43 insertions(+)

Comments

Shawn Guo Sept. 7, 2015, 2:42 a.m. UTC | #1
On Tue, Sep 01, 2015 at 05:49:13PM -0500, Adrian Alonso wrote:
> Add iomuxc-lpsr devicetree bindings documentation
> Provide documentation context as well an example on
> pheriperals that could use pad from either iomuxc controller
> supported by iMX7D SoC
> 
> Signed-off-by: Adrian Alonso <aalonso@freescale.com>
> ---
> Changes for V2: New patch on imx7d iomuxc-lpsr patch series
> 
>  .../bindings/pinctrl/fsl,imx7d-pinctrl.txt         | 43 ++++++++++++++++++++++
>  1 file changed, 43 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
> index 8bbf25d..c7310fc 100644
> --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
> @@ -1,10 +1,19 @@
>  * Freescale i.MX7 Dual IOMUX Controller
>  
> +iMX7D supports two iomuxc controllers, fsl,imx7d-iomuxc controller is similar
> +as previous iMX SoC generation and fsl,imx7d-iomuxc-lpsr which provides low
> +power state rentetion capabilities on gpios that are part of iomuxc-lpsr
> +(GPIO1_IO7..GPIO1_IO0).

I think the speciality of the select_input registers should be
mentioned too.

> +
> +Pheriparials using pads from iomuxc-lpsr support low state retention power
> +state, under LPSR mode GPIO's state of pads are retain.
> +
>  Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
>  and usage.
>  
>  Required properties:
>  - compatible: "fsl,imx7d-iomuxc"
> +- compatible: "fsl-imx7d-iomuxc-lpsr"

s/fsl-imx7d-iomuxc-lpsr/fsl,imx7d-iomuxc-lpsr

Shawn

>  - fsl,pins: each entry consists of 6 integers and represents the mux and config
>    setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
>    input_val> are specified using a PIN_FUNC_ID macro, which can be found in
> @@ -25,3 +34,37 @@ PAD_CTL_DSE_X1                  (0 << 0)
>  PAD_CTL_DSE_X2                  (1 << 0)
>  PAD_CTL_DSE_X3                  (2 << 0)
>  PAD_CTL_DSE_X4                  (3 << 0)
> +
> +Examples:
> +While iomuxc-lpsr is intended to be used by dedicated peripherals to take
> +advantages of LPSR power mode, is also possible that an IP to use pads from
> +any of the iomux controllers. For example the I2C1 IP can use SCL pad from
> +iomuxc-lpsr controller and SDA pad from iomuxc controller as:
> +
> +i2c1: i2c@30a20000 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1_1 &pinctrl_i2c1_2>;
> +	status = "okay";
> +};
> +
> +iomuxc-lpsr@302c0000 {
> +	compatible = "fsl,imx7d-iomuxc-lpsr";
> +	reg = <0x302c0000 0x10000>;
> +
> +	pinctrl_i2c1_1: i2c1grp-1 {
> +		fsl,pins = <
> +			MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x4000007f
> +		>;
> +	};
> +};
> +
> +iomuxc@30330000 {
> +	compatible = "fsl,imx7d-iomuxc";
> +	reg = <0x30330000 0x10000>;
> +
> +	pinctrl_i2c1_2: i2c1grp-2 {
> +		fsl,pins = <
> +			MX7D_PAD_I2C1_SCL__I2C1_SCL 0x4000007f
> +		>;
> +	};
> +};
> -- 
> 2.1.4
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Adrian Alonso Sept. 8, 2015, 4:15 p.m. UTC | #2
Hi Shawn,

See comments below.

Regards
Adrian

Patch
diff mbox

diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
index 8bbf25d..c7310fc 100644
--- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
@@ -1,10 +1,19 @@ 
 * Freescale i.MX7 Dual IOMUX Controller
 
+iMX7D supports two iomuxc controllers, fsl,imx7d-iomuxc controller is similar
+as previous iMX SoC generation and fsl,imx7d-iomuxc-lpsr which provides low
+power state rentetion capabilities on gpios that are part of iomuxc-lpsr
+(GPIO1_IO7..GPIO1_IO0).
+
+Pheriparials using pads from iomuxc-lpsr support low state retention power
+state, under LPSR mode GPIO's state of pads are retain.
+
 Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
 and usage.
 
 Required properties:
 - compatible: "fsl,imx7d-iomuxc"
+- compatible: "fsl-imx7d-iomuxc-lpsr"
 - fsl,pins: each entry consists of 6 integers and represents the mux and config
   setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
   input_val> are specified using a PIN_FUNC_ID macro, which can be found in
@@ -25,3 +34,37 @@  PAD_CTL_DSE_X1                  (0 << 0)
 PAD_CTL_DSE_X2                  (1 << 0)
 PAD_CTL_DSE_X3                  (2 << 0)
 PAD_CTL_DSE_X4                  (3 << 0)
+
+Examples:
+While iomuxc-lpsr is intended to be used by dedicated peripherals to take
+advantages of LPSR power mode, is also possible that an IP to use pads from
+any of the iomux controllers. For example the I2C1 IP can use SCL pad from
+iomuxc-lpsr controller and SDA pad from iomuxc controller as:
+
+i2c1: i2c@30a20000 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1_1 &pinctrl_i2c1_2>;
+	status = "okay";
+};
+
+iomuxc-lpsr@302c0000 {
+	compatible = "fsl,imx7d-iomuxc-lpsr";
+	reg = <0x302c0000 0x10000>;
+
+	pinctrl_i2c1_1: i2c1grp-1 {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x4000007f
+		>;
+	};
+};
+
+iomuxc@30330000 {
+	compatible = "fsl,imx7d-iomuxc";
+	reg = <0x30330000 0x10000>;
+
+	pinctrl_i2c1_2: i2c1grp-2 {
+		fsl,pins = <
+			MX7D_PAD_I2C1_SCL__I2C1_SCL 0x4000007f
+		>;
+	};
+};