@@ -5791,7 +5791,15 @@ static void ixgbe_close_suspend(struct ixgbe_adapter *adapter)
{
ixgbe_ptp_suspend(adapter);
- ixgbe_down(adapter);
+ if (adapter->hw.phy.ops.enter_lplu) {
+ adapter->hw.phy.reset_disable = true;
+ ixgbe_down(adapter);
+ adapter->hw.phy.ops.enter_lplu(&adapter->hw);
+ adapter->hw.phy.reset_disable = false;
+ } else {
+ ixgbe_down(adapter);
+ }
+
ixgbe_free_irq(adapter);
ixgbe_free_all_tx_resources(adapter);
@@ -848,6 +848,7 @@ struct ixgbe_thermal_sensor_data {
#define IXGBE_MDIO_AUTO_NEG_LINK_STATUS 0x4 /* Indicates if link is up */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_MASK 0x7 /* Speed/Duplex Mask */
+#define IXGBE_MDIO_AUTO_NEG_VEN_STAT_SPEED_MASK 0x6 /* Speed Mask */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10M_HALF 0x0 /* 10Mb/s Half Duplex */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10M_FULL 0x1 /* 10Mb/s Full Duplex */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_100M_HALF 0x2 /* 100Mb/s H Duplex */
@@ -856,6 +857,24 @@ struct ixgbe_thermal_sensor_data {
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_1GB_FULL 0x5 /* 1Gb/s Full Duplex */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB_HALF 0x6 /* 10Gb/s Half Duplex */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB_FULL 0x7 /* 10Gb/s Full Duplex */
+#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_1GB 0x4 /* 1Gb/s */
+#define IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB 0x6 /* 10Gb/s */
+
+#define IXGBE_MII_10GBASE_T_AUTONEG_CTRL_REG 0x20 /* 10G Control Reg */
+#define IXGBE_MII_AUTONEG_VENDOR_PROVISION_1_REG 0xC400 /* 1G Provisioning 1 */
+#define IXGBE_MII_AUTONEG_XNP_TX_REG 0x17 /* 1G XNP Transmit */
+#define IXGBE_MII_AUTONEG_ADVERTISE_REG 0x10 /* 100M Advertisement */
+#define IXGBE_MII_10GBASE_T_ADVERTISE 0x1000 /* full duplex, bit:12*/
+#define IXGBE_MII_1GBASE_T_ADVERTISE_XNP_TX 0x4000 /* full duplex, bit:14*/
+#define IXGBE_MII_1GBASE_T_ADVERTISE 0x8000 /* full duplex, bit:15*/
+#define IXGBE_MII_2_5GBASE_T_ADVERTISE 0x0400
+#define IXGBE_MII_5GBASE_T_ADVERTISE 0x0800
+#define IXGBE_MII_100BASE_T_ADVERTISE 0x0100 /* full duplex, bit:8 */
+#define IXGBE_MII_100BASE_T_ADVERTISE_HALF 0x0080 /* half duplex, bit:7 */
+#define IXGBE_MII_RESTART 0x200
+#define IXGBE_MII_AUTONEG_COMPLETE 0x20
+#define IXGBE_MII_AUTONEG_LINK_UP 0x04
+#define IXGBE_MII_AUTONEG_REG 0x0
/* Management */
#define IXGBE_MAVTV(_i) (0x05010 + ((_i) * 4)) /* 8 of these (0-7) */
@@ -1305,6 +1324,7 @@ struct ixgbe_thermal_sensor_data {
#define IXGBE_MDIO_AUTO_NEG_CONTROL 0x0 /* AUTO_NEG Control Reg */
#define IXGBE_MDIO_AUTO_NEG_STATUS 0x1 /* AUTO_NEG Status Reg */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_STAT 0xC800 /* AUTO_NEG Vendor Status Reg */
+#define IXGBE_MDIO_AUTO_NEG_VENDOR_TX_ALARM 0xCC00 /* AUTO_NEG Vendor TX Reg */
#define IXGBE_MDIO_AUTO_NEG_VENDOR_TX_ALARM2 0xCC01 /* AUTO_NEG Vendor Tx Reg */
#define IXGBE_MDIO_AUTO_NEG_VEN_LSC 0x1 /* AUTO_NEG Vendor Tx LSC */
#define IXGBE_MDIO_AUTO_NEG_ADVT 0x10 /* AUTO_NEG Advt Reg */
@@ -1312,7 +1332,8 @@ struct ixgbe_thermal_sensor_data {
#define IXGBE_MDIO_AUTO_NEG_EEE_ADVT 0x3C /* AUTO_NEG EEE Advt Reg */
#define IXGBE_MDIO_PHY_SET_LOW_POWER_MODE 0x0800 /* Set low power mode */
-
+#define IXGBE_AUTO_NEG_LP_STATUS 0xE820 /* AUTO NEG Rx LP Status Reg */
+#define IXGBE_AUTO_NEG_LP_1000BASE_CAP 0x8000 /* AUTO NEG Rx LP 1000BaseT */
#define IXGBE_MDIO_TX_VENDOR_ALARMS_3 0xCC02 /* Vendor Alarms 3 Reg */
#define IXGBE_MDIO_TX_VENDOR_ALARMS_3_RST_MASK 0x3 /* PHY Reset Complete Mask */
#define IXGBE_MDIO_GLOBAL_RES_PR_10 0xC479 /* Global Resv Provisioning 10 Reg */
@@ -2041,6 +2062,11 @@ enum {
#define IXGBE_NVM_POLL_WRITE 1 /* Flag for polling for write complete */
#define IXGBE_NVM_POLL_READ 0 /* Flag for polling for read complete */
+#define NVM_INIT_CTRL_3 0x38
+#define NVM_INIT_CTRL_3_LPLU 0x8
+#define NVM_INIT_CTRL_3_D10GMP_PORT0 0x40
+#define NVM_INIT_CTRL_3_D10GMP_PORT1 0x100
+
#define IXGBE_EEPROM_PAGE_SIZE_MAX 128
#define IXGBE_EEPROM_RD_BUFFER_MAX_COUNT 512 /* EEPROM words # read in burst */
#define IXGBE_EEPROM_WR_BUFFER_MAX_COUNT 256 /* EEPROM words # wr in burst */
@@ -3298,6 +3324,7 @@ struct ixgbe_phy_operations {
s32 (*write_i2c_combined)(struct ixgbe_hw *, u8 addr, u16 reg, u16 val);
s32 (*check_overtemp)(struct ixgbe_hw *);
s32 (*set_phy_power)(struct ixgbe_hw *, bool on);
+ s32 (*enter_lplu)(struct ixgbe_hw *);
s32 (*handle_lasi)(struct ixgbe_hw *hw);
};
@@ -3308,6 +3335,7 @@ struct ixgbe_eeprom_info {
u16 word_size;
u16 address_bits;
u16 word_page_size;
+ u16 ctrl_word_3;
};
#define IXGBE_FLAGS_DOUBLE_RESET_REQUIRED 0x01
@@ -3462,6 +3490,10 @@ struct ixgbe_info {
#define IXGBE_ERR_HOST_INTERFACE_COMMAND -33
#define IXGBE_NOT_IMPLEMENTED 0x7FFFFFFF
+#define IXGBE_FUSES0_GROUP(_i) (0x11158 + ((_i) * 4))
+#define IXGBE_FUSES0_300MHZ BIT(5)
+#define IXGBE_FUSES0_REV1 BIT(6)
+
#define IXGBE_KRM_PORT_CAR_GEN_CTRL(P) ((P == 0) ? (0x4010) : (0x8010))
#define IXGBE_KRM_LINK_CTRL_1(P) ((P == 0) ? (0x420C) : (0x820C))
#define IXGBE_KRM_DSP_TXFFE_STATE_4(P) ((P == 0) ? (0x4634) : (0x8634))
@@ -1458,6 +1458,143 @@ static s32 ixgbe_reset_phy_t_X550em(struct ixgbe_hw *hw)
return ixgbe_enable_lasi_ext_t_x550em(hw);
}
+/** ixgbe_get_lcd_x550em - Determine lowest common denominator
+ * @hw: pointer to hardware structure
+ * @lcd_speed: pointer to lowest common link speed
+ *
+ * Determine lowest common link speed with link partner.
+ **/
+s32 ixgbe_get_lcd_t_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *lcd_speed)
+{
+ u16 an_lp_status;
+ s32 status;
+ u16 word = hw->eeprom.ctrl_word_3;
+
+ *lcd_speed = IXGBE_LINK_SPEED_UNKNOWN;
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_AUTO_NEG_LP_STATUS,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &an_lp_status);
+ if (status)
+ return status;
+
+ /* If link partner advertised 1G, return 1G */
+ if (an_lp_status & IXGBE_AUTO_NEG_LP_1000BASE_CAP) {
+ *lcd_speed = IXGBE_LINK_SPEED_1GB_FULL;
+ return status;
+ }
+
+ /* If 10G disabled for LPLU via NVM D10GMP, then return no valid LCD */
+ if ((hw->bus.lan_id && (word & NVM_INIT_CTRL_3_D10GMP_PORT1)) ||
+ (word & NVM_INIT_CTRL_3_D10GMP_PORT0))
+ return status;
+
+ /* Link partner not capable of lower speeds, return 10G */
+ *lcd_speed = IXGBE_LINK_SPEED_10GB_FULL;
+ return status;
+}
+
+/** ixgbe_enter_lplu_x550em - Transition to low power states
+ * @hw: pointer to hardware structure
+ *
+ * Configures Low Power Link Up on transition to low power states
+ * (from D0 to non-D0). Link is required to enter LPLU so avoid resetting
+ * the X557 PHY immediately prior to entering LPLU.
+ **/
+s32 ixgbe_enter_lplu_t_x550em(struct ixgbe_hw *hw)
+{
+ u16 an_10g_cntl_reg, autoneg_reg, speed;
+ s32 status;
+ ixgbe_link_speed lcd_speed;
+ u32 save_autoneg;
+ bool link_up;
+
+ /* SW LPLU not required on later HW revisions. */
+ if (IXGBE_FUSES0_REV1 & IXGBE_READ_REG(hw, IXGBE_FUSES0_GROUP(0)))
+ return 0;
+
+ /* If blocked by MNG FW, then don't restart AN */
+ if (ixgbe_check_reset_blocked(hw))
+ return 0;
+
+ status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up);
+ if (status)
+ return status;
+
+ status = hw->eeprom.ops.read(hw, NVM_INIT_CTRL_3,
+ &hw->eeprom.ctrl_word_3);
+ if (status)
+ return status;
+
+ /* If link is down, LPLU disabled in NVM, WoL disabled, or
+ * manageability disabled, then force link down by entering
+ * low power mode.
+ */
+ if (!link_up || !(hw->eeprom.ctrl_word_3 & NVM_INIT_CTRL_3_LPLU) ||
+ !(hw->wol_enabled || ixgbe_mng_present(hw)))
+ return ixgbe_set_copper_phy_power(hw, false);
+
+ /* Determine LCD */
+ status = ixgbe_get_lcd_t_x550em(hw, &lcd_speed);
+ if (status)
+ return status;
+
+ /* If no valid LCD link speed, then force link down and exit. */
+ if (lcd_speed == IXGBE_LINK_SPEED_UNKNOWN)
+ return ixgbe_set_copper_phy_power(hw, false);
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_STAT,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &speed);
+ if (status)
+ return status;
+
+ /* If no link now, speed is invalid so take link down */
+ status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up);
+ if (status)
+ return ixgbe_set_copper_phy_power(hw, false);
+
+ /* clear everything but the speed bits */
+ speed &= IXGBE_MDIO_AUTO_NEG_VEN_STAT_SPEED_MASK;
+
+ /* If current speed is already LCD, then exit. */
+ if (((speed == IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_1GB) &&
+ (lcd_speed == IXGBE_LINK_SPEED_1GB_FULL)) ||
+ ((speed == IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB) &&
+ (lcd_speed == IXGBE_LINK_SPEED_10GB_FULL)))
+ return status;
+
+ /* Clear AN completed indication */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_TX_ALARM,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_reg);
+ if (status)
+ return status;
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_MII_10GBASE_T_AUTONEG_CTRL_REG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &an_10g_cntl_reg);
+ if (status)
+ return status;
+
+ status = hw->phy.ops.read_reg(hw,
+ IXGBE_MII_AUTONEG_VENDOR_PROVISION_1_REG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_reg);
+ if (status)
+ return status;
+
+ save_autoneg = hw->phy.autoneg_advertised;
+
+ /* Setup link at least common link speed */
+ status = hw->mac.ops.setup_link(hw, lcd_speed, false);
+
+ /* restore autoneg from before setting lplu speed */
+ hw->phy.autoneg_advertised = save_autoneg;
+
+ return status;
+}
+
/** ixgbe_init_phy_ops_X550em - PHY/SFP specific init
* @hw: pointer to hardware structure
*
@@ -1528,6 +1665,11 @@ static s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw)
ret_val = ixgbe_setup_kr_speed_x550em(hw, speed);
}
+ /* setup SW LPLU only for first revision */
+ if (!(IXGBE_FUSES0_REV1 & IXGBE_READ_REG(hw,
+ IXGBE_FUSES0_GROUP(0))))
+ phy->ops.enter_lplu = ixgbe_enter_lplu_t_x550em;
+
phy->ops.handle_lasi = ixgbe_handle_lasi_ext_t_x550em;
phy->ops.reset = ixgbe_reset_phy_t_X550em;
break;