| Message ID | 1434053294-10962-1-git-send-email-dhdang@apm.com |
|---|---|
| State | Changes Requested |
| Headers | show |
W dniu 11.06.2015 o 22:08, Duc Dang pisze:> X-Gene v1 PCIe controller has a bug in Configuration Request Retry > Status (CRS) logic: > When CPU tries to read Vendor ID and Device ID of not-existed > remote device, the controller returns 0xFFFF0001 instead of > 0xFFFFFFFF; this will add significant delay in boot time as > pci_bus_read_dev_vendor_id will wait for 60 seconds before > giving up. > > So for X-Gene v1 PCIe controllers, disable CRS capability > advertisement by clearing CRS Software Visibility bit before > returning the Root Capability value to the callers. This is done > by implementing X-Gene PCIe specific xgene_pcie_config_read32 for > CFG read accesses to replace the generic default pci_generic_config_read32 > function. > > Signed-off-by: Duc Dang <dhdang@apm.com> > --- > drivers/pci/host/pci-xgene.c | 48 +++++++++++++++++++++++++++++++++++++++++++- > 1 file changed, 47 insertions(+), 1 deletion(-) Tested-by: Marcin Juszkiewicz <mjuszkiewicz@redhat.com> Confirmed. It fixed issue. [ 0.842339] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.848235] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.855255] PCI host bridge /soc/pcie@1f2b0000 ranges: [ 0.860678] No bus range found for /soc/pcie@1f2b0000, using [bus 00-ff] [ 0.867950] IO 0xe010000000..0xe01000ffff -> 0x00000000 [ 0.873753] MEM 0xe180000000..0xe1ffffffff -> 0x80000000 [ 0.879592] xgene-pcie 1f2b0000.pcie: (rc) x1 gen-1 link up [ 0.885529] xgene-pcie 1f2b0000.pcie: PCI host bridge to bus 0000:00 [ 0.892248] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.898036] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.904556] pci_bus 0000:00: root bus resource [mem 0xe180000000-0xe1ffffffff] (bus address [0x80000000-0xffffffff]) [ 0.915741] pci 0000:00:00.0: IOMMU is currently not supported for PCI [ 0.922936] pci 0000:01:00.0: IOMMU is currently not supported for PCI [ 0.929937] pci 0000:01:00.0: of_irq_parse_pci() failed with rc=-19 [ 0.936616] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.947422] pci 0000:02:00.0: IOMMU is currently not supported for PCI [ 0.954439] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=none,locks=none [ 0.962946] pci 0000:00:00.0: BAR 14: assigned [mem 0xe180000000-0xe182ffffff] [ 0.970593] pci 0000:01:00.0: BAR 14: assigned [mem 0xe180000000-0xe182ffffff] [ 0.978239] pci 0000:02:00.0: BAR 0: assigned [mem 0xe180000000-0xe181ffffff pref] [ 0.986260] pci 0000:02:00.0: BAR 2: assigned [mem 0xe182000000-0xe1827fffff] [ 0.993828] pci 0000:02:00.0: BAR 6: assigned [mem 0xe182800000-0xe18281ffff pref] [ 1.001852] pci 0000:02:00.0: BAR 1: assigned [mem 0xe182820000-0xe182823fff] [ 1.009397] pci 0000:01:00.0: PCI bridge to [bus 02] [ 1.014637] pci 0000:01:00.0: bridge window [mem 0xe180000000-0xe182ffffff] [ 1.022200] pci 0000:00:00.0: PCI bridge to [bus 01-02] [ 1.027713] pci 0000:00:00.0: bridge window [mem 0xe180000000-0xe182ffffff] [ 1.035344] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt [ 1.042709] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 1.049577] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 1.056538] pci 0000:01:00.0: TI XIO2000a quirk detected; secondary bus fast back-to-back transfers disabled compared to [ 2040.117742] pci 0000:00:00.0: BAR 14: assigned [mem 0xe180000000-0xe182ffffff] Similar with Radeon card. -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thu, 2015-06-11 at 13:08 -0700, Duc Dang wrote: > X-Gene v1 PCIe controller has a bug in Configuration Request Retry > Status (CRS) logic: > When CPU tries to read Vendor ID and Device ID of not-existed > remote device, the controller returns 0xFFFF0001 instead of > 0xFFFFFFFF; this will add significant delay in boot time as > pci_bus_read_dev_vendor_id will wait for 60 seconds before > giving up. > > So for X-Gene v1 PCIe controllers, disable CRS capability > advertisement by clearing CRS Software Visibility bit before > returning the Root Capability value to the callers. This is done > by implementing X-Gene PCIe specific xgene_pcie_config_read32 for > CFG read accesses to replace the generic default pci_generic_config_read32 > function. > > Signed-off-by: Duc Dang <dhdang@apm.com> Applied onto v4.1-rc7 and: Tested-by: Ian Campbell <ian.campbell@citrix.com> Thanks! -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Duc, On Thu, Jun 11, 2015 at 01:08:14PM -0700, Duc Dang wrote: > X-Gene v1 PCIe controller has a bug in Configuration Request Retry > Status (CRS) logic: > When CPU tries to read Vendor ID and Device ID of not-existed > remote device, the controller returns 0xFFFF0001 instead of > 0xFFFFFFFF; this will add significant delay in boot time as > pci_bus_read_dev_vendor_id will wait for 60 seconds before > giving up. OK, help me understand how this works. I think this is related to the problem I reported where if the slot is empty, "lspci" doesn't show anything, not even the Root Port leading to the slot. I think this happens because when we try to read the Root Port's config space, - the slot below the Root Port is empty - the Root Port's link is down - xgene_pcie_map_bus() returns NULL because !port->link_up - pci_generic_config_read32() returns PCIBIOS_DEVICE_NOT_FOUND so it looks like the Root Port itself doesn't exist. I proposed to change xgene_pcie_map_bus() so it didn't check whether the link was up. That change makes reads of the Root Port's config space work. After we learn the Root Port exists, the PCI core enumerates devices below the Root Port, e.g., on bus 01. X-Gene advertises that it supports CRS, so we enable it. When we try to read the Vendor ID of 01:00.0, there's no response from the device (because the slot is empty), and the Root Complex should complete the read by fabricating data of all ones, i.e., 0xFFFFFFFF. But apparently X-Gene supplies 0xFFFF0001 instead, which means "there's a device here, but it's not ready yet," so the PCI core retries the read for 60 seconds before timing out. This patch is basically a quirk that keeps X-Gene from advertising CRS support, so the PCI core won't enable CRS. In the example above, I guess that means the Root Complex will supply 0xFFFFFFFF and the core will see that the slot is empty. But this patch leaves the "!port->link_up" test in xgene_pcie_map_bus(). Doesn't that mean the core will still not discover the Root Port when the slot is empty? It seems to me that you would want both the xgene_pcie_map_bus() change and this patch. The first would fix the problem that we don't enumerate Root Ports leading to empty slots, and the second would fix the problem that we enable CRS and timeout when enumerating below those Root Ports. One more question below: > So for X-Gene v1 PCIe controllers, disable CRS capability > advertisement by clearing CRS Software Visibility bit before > returning the Root Capability value to the callers. This is done > by implementing X-Gene PCIe specific xgene_pcie_config_read32 for > CFG read accesses to replace the generic default pci_generic_config_read32 > function. > > Signed-off-by: Duc Dang <dhdang@apm.com> > --- > drivers/pci/host/pci-xgene.c | 48 +++++++++++++++++++++++++++++++++++++++++++- > 1 file changed, 47 insertions(+), 1 deletion(-) > > diff --git a/drivers/pci/host/pci-xgene.c b/drivers/pci/host/pci-xgene.c > index ee082c0..741a253 100644 > --- a/drivers/pci/host/pci-xgene.c > +++ b/drivers/pci/host/pci-xgene.c > @@ -59,6 +59,12 @@ > #define SZ_1T (SZ_1G*1024ULL) > #define PIPE_PHY_RATE_RD(src) ((0xc000 & (u32)(src)) >> 0xe) > > +#define ROOT_CAP_AND_CTRL 0x5C > + > +/* PCIe IP version */ > +#define XGENE_PCIE_IP_VER_UNKN 0 > +#define XGENE_PCIE_IP_VER_1 1 > + > struct xgene_pcie_port { > struct device_node *node; > struct device *dev; > @@ -67,6 +73,7 @@ struct xgene_pcie_port { > void __iomem *cfg_base; > unsigned long cfg_addr; > bool link_up; > + u32 version; > }; > > static inline u32 pcie_bar_low_val(u32 addr, u32 flags) > @@ -140,9 +147,44 @@ static void __iomem *xgene_pcie_map_bus(struct pci_bus *bus, unsigned int devfn, > return xgene_pcie_get_cfg_base(bus) + offset; > } > > +int xgene_pcie_config_read32(struct pci_bus *bus, unsigned int devfn, > + int where, int size, u32 *val) > +{ > + void __iomem *addr; > + struct xgene_pcie_port *port = bus->sysdata; > + > + addr = bus->ops->map_bus(bus, devfn, where & ~0x3); > + if (!addr) { > + *val = ~0; > + return PCIBIOS_DEVICE_NOT_FOUND; > + } > + > + *val = readl(addr); Can't you just call pci_generic_config_read32() directly instead of duplicating its code here? > + /* > + * X-Gene v1 PCIe controller has a bug in Configuration Request > + * Retry Status (CRS) logic: > + * When CPU tries to read Vendor ID and Device ID of not-existed > + * remote device, the controller returns 0xFFFF0001 instead of > + * 0xFFFFFFFF; this will add significant delay in boot time as > + * pci_bus_read_dev_vendor_id will wait for 60 seconds before > + * giving up. > + * So for X-Gene v1 PCIe controllers, disable CRS capability > + * advertisement by clearing CRS Software Visibility bit before > + * returning the Root Capability value to the callers. > + */ > + if (pci_is_root_bus(bus) && (port->version == XGENE_PCIE_IP_VER_1) && > + ((where & ~0x3) == ROOT_CAP_AND_CTRL)) > + *val &= ~(PCI_EXP_RTCAP_CRSVIS << 16); > + > + if (size <= 2) > + *val = (*val >> (8 * (where & 3))) & ((1 << (size * 8)) - 1); > + > + return PCIBIOS_SUCCESSFUL; > +} > + > static struct pci_ops xgene_pcie_ops = { > .map_bus = xgene_pcie_map_bus, > - .read = pci_generic_config_read32, > + .read = xgene_pcie_config_read32, > .write = pci_generic_config_write32, > }; > > @@ -483,6 +525,10 @@ static int xgene_pcie_probe_bridge(struct platform_device *pdev) > port->node = of_node_get(pdev->dev.of_node); > port->dev = &pdev->dev; > > + port->version = XGENE_PCIE_IP_VER_UNKN; > + if (of_device_is_compatible(port->node, "apm,xgene-pcie")) > + port->version = XGENE_PCIE_IP_VER_1; > + > ret = xgene_pcie_map_reg(port, pdev); > if (ret) > return ret; > -- > 1.9.1 > -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Bjorn, On Fri, Jun 12, 2015 at 2:59 PM, Bjorn Helgaas <bhelgaas@google.com> wrote: > Hi Duc, > > On Thu, Jun 11, 2015 at 01:08:14PM -0700, Duc Dang wrote: >> X-Gene v1 PCIe controller has a bug in Configuration Request Retry >> Status (CRS) logic: >> When CPU tries to read Vendor ID and Device ID of not-existed >> remote device, the controller returns 0xFFFF0001 instead of >> 0xFFFFFFFF; this will add significant delay in boot time as >> pci_bus_read_dev_vendor_id will wait for 60 seconds before >> giving up. > > OK, help me understand how this works. I think this is related to the > problem I reported where if the slot is empty, "lspci" doesn't show > anything, not even the Root Port leading to the slot. > > I think this happens because when we try to read the Root Port's config > space, > > - the slot below the Root Port is empty > - the Root Port's link is down > - xgene_pcie_map_bus() returns NULL because !port->link_up > - pci_generic_config_read32() returns PCIBIOS_DEVICE_NOT_FOUND > > so it looks like the Root Port itself doesn't exist. > > I proposed to change xgene_pcie_map_bus() so it didn't check whether the > link was up. That change makes reads of the Root Port's config space work. > > After we learn the Root Port exists, the PCI core enumerates devices below > the Root Port, e.g., on bus 01. X-Gene advertises that it supports CRS, so > we enable it. When we try to read the Vendor ID of 01:00.0, there's no > response from the device (because the slot is empty), and the Root Complex > should complete the read by fabricating data of all ones, i.e., 0xFFFFFFFF. > But apparently X-Gene supplies 0xFFFF0001 instead, which means "there's a > device here, but it's not ready yet," so the PCI core retries the read for > 60 seconds before timing out. > > This patch is basically a quirk that keeps X-Gene from advertising CRS > support, so the PCI core won't enable CRS. In the example above, I guess > that means the Root Complex will supply 0xFFFFFFFF and the core will see > that the slot is empty. > > But this patch leaves the "!port->link_up" test in xgene_pcie_map_bus(). > Doesn't that mean the core will still not discover the Root Port when the > slot is empty? > > It seems to me that you would want both the xgene_pcie_map_bus() change and > this patch. The first would fix the problem that we don't enumerate Root > Ports leading to empty slots, and the second would fix the problem that we > enable CRS and timeout when enumerating below those Root Ports. > Yes, you are right. I plan to send a follow up patch after this one to remove the port->link_up check in xgene_pcie_map_bus and make root port discoverable even when the slot is empty. I can combine this follow up patch with this one if you feel OK with it. > One more question below: > >> So for X-Gene v1 PCIe controllers, disable CRS capability >> advertisement by clearing CRS Software Visibility bit before >> returning the Root Capability value to the callers. This is done >> by implementing X-Gene PCIe specific xgene_pcie_config_read32 for >> CFG read accesses to replace the generic default pci_generic_config_read32 >> function. >> >> Signed-off-by: Duc Dang <dhdang@apm.com> >> --- >> drivers/pci/host/pci-xgene.c | 48 +++++++++++++++++++++++++++++++++++++++++++- >> 1 file changed, 47 insertions(+), 1 deletion(-) >> >> diff --git a/drivers/pci/host/pci-xgene.c b/drivers/pci/host/pci-xgene.c >> index ee082c0..741a253 100644 >> --- a/drivers/pci/host/pci-xgene.c >> +++ b/drivers/pci/host/pci-xgene.c >> @@ -59,6 +59,12 @@ >> #define SZ_1T (SZ_1G*1024ULL) >> #define PIPE_PHY_RATE_RD(src) ((0xc000 & (u32)(src)) >> 0xe) >> >> +#define ROOT_CAP_AND_CTRL 0x5C >> + >> +/* PCIe IP version */ >> +#define XGENE_PCIE_IP_VER_UNKN 0 >> +#define XGENE_PCIE_IP_VER_1 1 >> + >> struct xgene_pcie_port { >> struct device_node *node; >> struct device *dev; >> @@ -67,6 +73,7 @@ struct xgene_pcie_port { >> void __iomem *cfg_base; >> unsigned long cfg_addr; >> bool link_up; >> + u32 version; >> }; >> >> static inline u32 pcie_bar_low_val(u32 addr, u32 flags) >> @@ -140,9 +147,44 @@ static void __iomem *xgene_pcie_map_bus(struct pci_bus *bus, unsigned int devfn, >> return xgene_pcie_get_cfg_base(bus) + offset; >> } >> >> +int xgene_pcie_config_read32(struct pci_bus *bus, unsigned int devfn, >> + int where, int size, u32 *val) >> +{ >> + void __iomem *addr; >> + struct xgene_pcie_port *port = bus->sysdata; >> + >> + addr = bus->ops->map_bus(bus, devfn, where & ~0x3); >> + if (!addr) { >> + *val = ~0; >> + return PCIBIOS_DEVICE_NOT_FOUND; >> + } >> + >> + *val = readl(addr); > > Can't you just call pci_generic_config_read32() directly instead of > duplicating its code here? > Yes, I will replace above code with: pci_generic_config_read32(bus, devfn, where & ~0x3, 4, *val) to read 4 bytes to *val; >> + /* >> + * X-Gene v1 PCIe controller has a bug in Configuration Request >> + * Retry Status (CRS) logic: >> + * When CPU tries to read Vendor ID and Device ID of not-existed >> + * remote device, the controller returns 0xFFFF0001 instead of >> + * 0xFFFFFFFF; this will add significant delay in boot time as >> + * pci_bus_read_dev_vendor_id will wait for 60 seconds before >> + * giving up. >> + * So for X-Gene v1 PCIe controllers, disable CRS capability >> + * advertisement by clearing CRS Software Visibility bit before >> + * returning the Root Capability value to the callers. >> + */ >> + if (pci_is_root_bus(bus) && (port->version == XGENE_PCIE_IP_VER_1) && >> + ((where & ~0x3) == ROOT_CAP_AND_CTRL)) >> + *val &= ~(PCI_EXP_RTCAP_CRSVIS << 16); >> + >> + if (size <= 2) >> + *val = (*val >> (8 * (where & 3))) & ((1 << (size * 8)) - 1); >> + >> + return PCIBIOS_SUCCESSFUL; >> +} >> + >> static struct pci_ops xgene_pcie_ops = { >> .map_bus = xgene_pcie_map_bus, >> - .read = pci_generic_config_read32, >> + .read = xgene_pcie_config_read32, >> .write = pci_generic_config_write32, >> }; >> >> @@ -483,6 +525,10 @@ static int xgene_pcie_probe_bridge(struct platform_device *pdev) >> port->node = of_node_get(pdev->dev.of_node); >> port->dev = &pdev->dev; >> >> + port->version = XGENE_PCIE_IP_VER_UNKN; >> + if (of_device_is_compatible(port->node, "apm,xgene-pcie")) >> + port->version = XGENE_PCIE_IP_VER_1; >> + >> ret = xgene_pcie_map_reg(port, pdev); >> if (ret) >> return ret; >> -- >> 1.9.1 >>
On Fri, Jun 12, 2015 at 5:10 PM, Duc Dang <dhdang@apm.com> wrote: > Hi Bjorn, > > On Fri, Jun 12, 2015 at 2:59 PM, Bjorn Helgaas <bhelgaas@google.com> wrote: >> Hi Duc, >> >> On Thu, Jun 11, 2015 at 01:08:14PM -0700, Duc Dang wrote: >>> X-Gene v1 PCIe controller has a bug in Configuration Request Retry >>> Status (CRS) logic: >>> When CPU tries to read Vendor ID and Device ID of not-existed >>> remote device, the controller returns 0xFFFF0001 instead of >>> 0xFFFFFFFF; this will add significant delay in boot time as >>> pci_bus_read_dev_vendor_id will wait for 60 seconds before >>> giving up. >> >> OK, help me understand how this works. I think this is related to the >> problem I reported where if the slot is empty, "lspci" doesn't show >> anything, not even the Root Port leading to the slot. >> >> I think this happens because when we try to read the Root Port's config >> space, >> >> - the slot below the Root Port is empty >> - the Root Port's link is down >> - xgene_pcie_map_bus() returns NULL because !port->link_up >> - pci_generic_config_read32() returns PCIBIOS_DEVICE_NOT_FOUND >> >> so it looks like the Root Port itself doesn't exist. >> >> I proposed to change xgene_pcie_map_bus() so it didn't check whether the >> link was up. That change makes reads of the Root Port's config space work. >> >> After we learn the Root Port exists, the PCI core enumerates devices below >> the Root Port, e.g., on bus 01. X-Gene advertises that it supports CRS, so >> we enable it. When we try to read the Vendor ID of 01:00.0, there's no >> response from the device (because the slot is empty), and the Root Complex >> should complete the read by fabricating data of all ones, i.e., 0xFFFFFFFF. >> But apparently X-Gene supplies 0xFFFF0001 instead, which means "there's a >> device here, but it's not ready yet," so the PCI core retries the read for >> 60 seconds before timing out. >> >> This patch is basically a quirk that keeps X-Gene from advertising CRS >> support, so the PCI core won't enable CRS. In the example above, I guess >> that means the Root Complex will supply 0xFFFFFFFF and the core will see >> that the slot is empty. >> >> But this patch leaves the "!port->link_up" test in xgene_pcie_map_bus(). >> Doesn't that mean the core will still not discover the Root Port when the >> slot is empty? >> >> It seems to me that you would want both the xgene_pcie_map_bus() change and >> this patch. The first would fix the problem that we don't enumerate Root >> Ports leading to empty slots, and the second would fix the problem that we >> enable CRS and timeout when enumerating below those Root Ports. >> > Yes, you are right. I plan to send a follow up patch after this one to > remove the port->link_up check in xgene_pcie_map_bus and make root > port discoverable even when the slot is empty. I can combine this > follow up patch with this one if you feel OK with it. Two patches would be great. I just didn't know about your plans for the follow-up one. Bjorn -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/pci/host/pci-xgene.c b/drivers/pci/host/pci-xgene.c index ee082c0..741a253 100644 --- a/drivers/pci/host/pci-xgene.c +++ b/drivers/pci/host/pci-xgene.c @@ -59,6 +59,12 @@ #define SZ_1T (SZ_1G*1024ULL) #define PIPE_PHY_RATE_RD(src) ((0xc000 & (u32)(src)) >> 0xe) +#define ROOT_CAP_AND_CTRL 0x5C + +/* PCIe IP version */ +#define XGENE_PCIE_IP_VER_UNKN 0 +#define XGENE_PCIE_IP_VER_1 1 + struct xgene_pcie_port { struct device_node *node; struct device *dev; @@ -67,6 +73,7 @@ struct xgene_pcie_port { void __iomem *cfg_base; unsigned long cfg_addr; bool link_up; + u32 version; }; static inline u32 pcie_bar_low_val(u32 addr, u32 flags) @@ -140,9 +147,44 @@ static void __iomem *xgene_pcie_map_bus(struct pci_bus *bus, unsigned int devfn, return xgene_pcie_get_cfg_base(bus) + offset; } +int xgene_pcie_config_read32(struct pci_bus *bus, unsigned int devfn, + int where, int size, u32 *val) +{ + void __iomem *addr; + struct xgene_pcie_port *port = bus->sysdata; + + addr = bus->ops->map_bus(bus, devfn, where & ~0x3); + if (!addr) { + *val = ~0; + return PCIBIOS_DEVICE_NOT_FOUND; + } + + *val = readl(addr); + /* + * X-Gene v1 PCIe controller has a bug in Configuration Request + * Retry Status (CRS) logic: + * When CPU tries to read Vendor ID and Device ID of not-existed + * remote device, the controller returns 0xFFFF0001 instead of + * 0xFFFFFFFF; this will add significant delay in boot time as + * pci_bus_read_dev_vendor_id will wait for 60 seconds before + * giving up. + * So for X-Gene v1 PCIe controllers, disable CRS capability + * advertisement by clearing CRS Software Visibility bit before + * returning the Root Capability value to the callers. + */ + if (pci_is_root_bus(bus) && (port->version == XGENE_PCIE_IP_VER_1) && + ((where & ~0x3) == ROOT_CAP_AND_CTRL)) + *val &= ~(PCI_EXP_RTCAP_CRSVIS << 16); + + if (size <= 2) + *val = (*val >> (8 * (where & 3))) & ((1 << (size * 8)) - 1); + + return PCIBIOS_SUCCESSFUL; +} + static struct pci_ops xgene_pcie_ops = { .map_bus = xgene_pcie_map_bus, - .read = pci_generic_config_read32, + .read = xgene_pcie_config_read32, .write = pci_generic_config_write32, }; @@ -483,6 +525,10 @@ static int xgene_pcie_probe_bridge(struct platform_device *pdev) port->node = of_node_get(pdev->dev.of_node); port->dev = &pdev->dev; + port->version = XGENE_PCIE_IP_VER_UNKN; + if (of_device_is_compatible(port->node, "apm,xgene-pcie")) + port->version = XGENE_PCIE_IP_VER_1; + ret = xgene_pcie_map_reg(port, pdev); if (ret) return ret;
X-Gene v1 PCIe controller has a bug in Configuration Request Retry Status (CRS) logic: When CPU tries to read Vendor ID and Device ID of not-existed remote device, the controller returns 0xFFFF0001 instead of 0xFFFFFFFF; this will add significant delay in boot time as pci_bus_read_dev_vendor_id will wait for 60 seconds before giving up. So for X-Gene v1 PCIe controllers, disable CRS capability advertisement by clearing CRS Software Visibility bit before returning the Root Capability value to the callers. This is done by implementing X-Gene PCIe specific xgene_pcie_config_read32 for CFG read accesses to replace the generic default pci_generic_config_read32 function. Signed-off-by: Duc Dang <dhdang@apm.com> --- drivers/pci/host/pci-xgene.c | 48 +++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 47 insertions(+), 1 deletion(-)