| Message ID | 1433484148-7464-3-git-send-email-suneel.garapati@xilinx.com |
|---|---|
| State | Not Applicable |
| Delegated to: | David Miller |
| Headers | show |
On 06/05/2015 08:02 AM, Suneel Garapati wrote: > Adds support for Ceva sata host controller on Xilinx > Zynq UltraScale+ MPSoC. > > Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com> > --- > Changes v2 > - Change module license string to GPL v2 > --- > drivers/ata/Kconfig | 9 ++ > drivers/ata/Makefile | 1 + > drivers/ata/ahci_ceva.c | 225 ++++++++++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 235 insertions(+) > create mode 100644 drivers/ata/ahci_ceva.c > > diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig > index b4524f4..6d17a3b 100644 > --- a/drivers/ata/Kconfig > +++ b/drivers/ata/Kconfig > @@ -133,6 +133,15 @@ config AHCI_IMX > > If unsure, say N. > > +config AHCI_CEVA > + tristate "CEVA AHCI SATA support" > + depends on OF > + help > + This option enables support for the CEVA AHCI SATA. > + It can be found on the Xilinx Zynq UltraScale+ MPSoC. > + > + If unsure, say N. > + > config AHCI_MVEBU > tristate "Marvell EBU AHCI SATA support" > depends on ARCH_MVEBU > diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile > index 5154753..af70919 100644 > --- a/drivers/ata/Makefile > +++ b/drivers/ata/Makefile > @@ -11,6 +11,7 @@ obj-$(CONFIG_SATA_SIL24) += sata_sil24.o > obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o > obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o libahci.o > obj-$(CONFIG_AHCI_BRCMSTB) += ahci_brcmstb.o libahci.o libahci_platform.o > +obj-$(CONFIG_AHCI_CEVA) += ahci_ceva.o libahci.o libahci_platform.o > obj-$(CONFIG_AHCI_DA850) += ahci_da850.o libahci.o libahci_platform.o > obj-$(CONFIG_AHCI_IMX) += ahci_imx.o libahci.o libahci_platform.o > obj-$(CONFIG_AHCI_MVEBU) += ahci_mvebu.o libahci.o libahci_platform.o > diff --git a/drivers/ata/ahci_ceva.c b/drivers/ata/ahci_ceva.c > new file mode 100644 > index 0000000..559d960 > --- /dev/null > +++ b/drivers/ata/ahci_ceva.c > @@ -0,0 +1,225 @@ > +/* > + * Copyright (C) 2015 Xilinx, Inc. > + * CEVA AHCI SATA platform driver > + * > + * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms and conditions of the GNU General Public License, > + * version 2, as published by the Free Software Foundation. > + * > + * This program is distributed in the hope it will be useful, but WITHOUT > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for > + * more details. > + * > + * You should have received a copy of the GNU General Public License along with > + * this program. If not, see <http://www.gnu.org/licenses/>. > + */ > + > +#include <linux/ahci_platform.h> > +#include <linux/kernel.h> > +#include <linux/libata.h> > +#include <linux/module.h> > +#include <linux/of_device.h> > +#include <linux/platform_device.h> > +#include "ahci.h" > + > +/* Vendor Specific Register Offsets */ > +#define AHCI_VEND_PCFG 0xA4 > +#define AHCI_VEND_PPCFG 0xA8 > +#define AHCI_VEND_PP2C 0xAC > +#define AHCI_VEND_PP3C 0xB0 > +#define AHCI_VEND_PP4C 0xB4 > +#define AHCI_VEND_PP5C 0xB8 > +#define AHCI_VEND_PAXIC 0xC0 > +#define AHCI_VEND_PTC 0xC8 > + > +/* Vendor Specific Register bit definitions */ > +#define PAXIC_ADBW_BW64 0x1 > +#define PAXIC_MAWIDD (1 << 8) > +#define PAXIC_MARIDD (1 << 16) > +#define PAXIC_OTL (0x4 << 20) > + > +#define PCFG_TPSS_VAL (0x32 << 16) > +#define PCFG_TPRS_VAL (0x2 << 12) > +#define PCFG_PAD_VAL 0x2 > + > +#define PPCFG_TTA 0x1FFFE > +#define PPCFG_PSSO_EN (1 << 28) > +#define PPCFG_PSS_EN (1 << 29) > +#define PPCFG_ESDF_EN (1 << 31) > + > +#define PP2C_CIBGMN 0x0F > +#define PP2C_CIBGMX (0x25 << 8) > +#define PP2C_CIBGN (0x18 << 16) > +#define PP2C_CINMP (0x29 << 24) > + > +#define PP3C_CWBGMN 0x04 > +#define PP3C_CWBGMX (0x0B << 8) > +#define PP3C_CWBGN (0x08 << 16) > +#define PP3C_CWNMP (0x0F << 24) > + > +#define PP4C_BMX 0x0a > +#define PP4C_BNM (0x08 << 8) > +#define PP4C_SFD (0x4a << 16) > +#define PP4C_PTST (0x06 << 24) > + > +#define PP5C_RIT 0x60216 > +#define PP5C_RCT (0x7f0 << 20) > + > +#define PTC_RX_WM_VAL 0x40 > +#define PTC_RSVD (1 << 27) > + > +#define PORT0_BASE 0x100 > +#define PORT1_BASE 0x180 > + > +/* Port Control Register Bit Definitions */ > +#define PORT_SCTL_SPD_GEN2 (0x2 << 4) > +#define PORT_SCTL_SPD_GEN1 (0x1 << 4) > +#define PORT_SCTL_IPM (0x3 << 8) > + > +#define PORT_BASE 0x100 > +#define PORT_OFFSET 0x80 > +#define NR_PORTS 2 > +#define DRV_NAME "ahci-ceva" > +#define CEVA_FLAG_BROKEN_GEN2 1 > + > +struct ceva_ahci_priv { > + struct platform_device *ahci_pdev; > + int flags; > +}; > + > +static struct ata_port_operations ahci_ceva_ops = { > + .inherits = &ahci_platform_ops, > +}; > + > +static const struct ata_port_info ahci_ceva_port_info = { > + .flags = AHCI_FLAG_COMMON, > + .pio_mask = ATA_PIO4, > + .udma_mask = ATA_UDMA6, > + .port_ops = &ahci_ceva_ops, > +}; > + > +static void ahci_ceva_setup(struct ahci_host_priv *hpriv) > +{ > + void __iomem *mmio = hpriv->mmio; > + struct ceva_ahci_priv *cevapriv = hpriv->plat_data; > + u32 tmp; > + int i; > + > + /* > + * AXI Data bus width to 64 > + * Set Mem Addr Read, Write ID for data transfers > + * Transfer limit to 72 DWord > + */ > + tmp = PAXIC_ADBW_BW64 | PAXIC_MAWIDD | PAXIC_MARIDD | PAXIC_OTL; > + writel(tmp, mmio + AHCI_VEND_PAXIC); > + > + /* Set AHCI Enable */ > + tmp = readl(mmio + HOST_CTL); > + tmp |= HOST_AHCI_EN; > + writel(tmp, mmio + HOST_CTL); > + > + for (i = 0; i < NR_PORTS; i++) { > + /* TPSS TPRS scalars, CISE and Port Addr */ > + tmp = PCFG_TPSS_VAL | PCFG_TPRS_VAL | (PCFG_PAD_VAL + i); > + writel(tmp, mmio + AHCI_VEND_PCFG); > + > + /* Port Phy Cfg register enables */ > + tmp = PPCFG_TTA | PPCFG_PSS_EN | PPCFG_ESDF_EN; > + writel(tmp, mmio + AHCI_VEND_PPCFG); > + > + /* Phy Control OOB timing parameters COMINIT */ > + tmp = PP2C_CIBGMN | PP2C_CIBGMX | PP2C_CIBGN | PP2C_CINMP; > + writel(tmp, mmio + AHCI_VEND_PP2C); > + > + /* Phy Control OOB timing parameters COMWAKE */ > + tmp = PP3C_CWBGMN | PP3C_CWBGMX | PP3C_CWBGN | PP3C_CWNMP; > + writel(tmp, mmio + AHCI_VEND_PP3C); > + > + /* Phy Control Burst timing setting */ > + tmp = PP4C_BMX | PP4C_BNM | PP4C_SFD | PP4C_PTST; > + writel(tmp, mmio + AHCI_VEND_PP4C); > + > + /* Rate Change Timer and Retry Interval Timer setting */ > + tmp = PP5C_RIT | PP5C_RCT; > + writel(tmp, mmio + AHCI_VEND_PP5C); > + > + /* Rx Watermark setting */ > + tmp = PTC_RX_WM_VAL | PTC_RSVD; > + writel(tmp, mmio + AHCI_VEND_PTC); > + > + /* Default to Gen 2 Speed and Gen 1 if Gen2 is broken */ > + tmp = PORT_SCTL_SPD_GEN2 | PORT_SCTL_IPM; > + if (cevapriv->flags & CEVA_FLAG_BROKEN_GEN2) > + tmp = PORT_SCTL_SPD_GEN1 | PORT_SCTL_IPM; > + writel(tmp, mmio + PORT_SCR_CTL + PORT_BASE + PORT_OFFSET * i); > + } > +} > + > +static struct scsi_host_template ahci_platform_sht = { > + AHCI_SHT(DRV_NAME), > +}; > + > +static int ceva_ahci_probe(struct platform_device *pdev) > +{ > + struct device_node *np = pdev->dev.of_node; > + struct device *dev = &pdev->dev; > + struct ahci_host_priv *hpriv; > + struct ceva_ahci_priv *cevapriv; > + > + cevapriv = devm_kzalloc(dev, sizeof(*cevapriv), GFP_KERNEL); > + if (!cevapriv) > + return -ENOMEM; > + > + cevapriv->ahci_pdev = pdev; > + > + hpriv = ahci_platform_get_resources(pdev); > + if (IS_ERR(hpriv)) > + return PTR_ERR(hpriv); > + > + if (of_property_read_bool(np, "ceva,broken-gen2")) > + cevapriv->flags = CEVA_FLAG_BROKEN_GEN2; > + > + hpriv->plat_data = cevapriv; > + > + /* CEVA specific initialization */ > + ahci_ceva_setup(hpriv); > + > + return ahci_platform_init_host(pdev, hpriv, &ahci_ceva_port_info, > + &ahci_platform_sht); > +} > + > +static int __maybe_unused ceva_ahci_suspend(struct device *dev) > +{ > + return ahci_platform_suspend_host(dev); > +} > + > +static int __maybe_unused ceva_ahci_resume(struct device *dev) > +{ > + return ahci_platform_resume_host(dev); > +} > + > +static SIMPLE_DEV_PM_OPS(ahci_ceva_pm_ops, ceva_ahci_suspend, ceva_ahci_resume); > + > +static const struct of_device_id ceva_ahci_of_match[] = { > + { .compatible = "ceva,ahci-1v84" }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, ceva_ahci_of_match); > + > +static struct platform_driver ceva_ahci_driver = { > + .probe = ceva_ahci_probe, > + .remove = ata_platform_remove_one, > + .driver = { > + .name = DRV_NAME, > + .of_match_table = ceva_ahci_of_match, > + .pm = &ahci_ceva_pm_ops, > + }, > +}; > +module_platform_driver(ceva_ahci_driver); > + > +MODULE_DESCRIPTION("CEVA AHCI SATA platform driver"); > +MODULE_AUTHOR("Xilinx Inc."); > +MODULE_LICENSE("GPL v2"); > -- > 2.1.2 Tested-by: Michal Simek <michal.simek@xilinx.com> Thanks, Michal
cc'ing Hans and quoting whole message. Hans, can you please review this one? Thanks. On Fri, Jun 05, 2015 at 11:32:28AM +0530, Suneel Garapati wrote: > Adds support for Ceva sata host controller on Xilinx > Zynq UltraScale+ MPSoC. > > Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com> > --- > Changes v2 > - Change module license string to GPL v2 > --- > drivers/ata/Kconfig | 9 ++ > drivers/ata/Makefile | 1 + > drivers/ata/ahci_ceva.c | 225 ++++++++++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 235 insertions(+) > create mode 100644 drivers/ata/ahci_ceva.c > > diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig > index b4524f4..6d17a3b 100644 > --- a/drivers/ata/Kconfig > +++ b/drivers/ata/Kconfig > @@ -133,6 +133,15 @@ config AHCI_IMX > > If unsure, say N. > > +config AHCI_CEVA > + tristate "CEVA AHCI SATA support" > + depends on OF > + help > + This option enables support for the CEVA AHCI SATA. > + It can be found on the Xilinx Zynq UltraScale+ MPSoC. > + > + If unsure, say N. > + > config AHCI_MVEBU > tristate "Marvell EBU AHCI SATA support" > depends on ARCH_MVEBU > diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile > index 5154753..af70919 100644 > --- a/drivers/ata/Makefile > +++ b/drivers/ata/Makefile > @@ -11,6 +11,7 @@ obj-$(CONFIG_SATA_SIL24) += sata_sil24.o > obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o > obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o libahci.o > obj-$(CONFIG_AHCI_BRCMSTB) += ahci_brcmstb.o libahci.o libahci_platform.o > +obj-$(CONFIG_AHCI_CEVA) += ahci_ceva.o libahci.o libahci_platform.o > obj-$(CONFIG_AHCI_DA850) += ahci_da850.o libahci.o libahci_platform.o > obj-$(CONFIG_AHCI_IMX) += ahci_imx.o libahci.o libahci_platform.o > obj-$(CONFIG_AHCI_MVEBU) += ahci_mvebu.o libahci.o libahci_platform.o > diff --git a/drivers/ata/ahci_ceva.c b/drivers/ata/ahci_ceva.c > new file mode 100644 > index 0000000..559d960 > --- /dev/null > +++ b/drivers/ata/ahci_ceva.c > @@ -0,0 +1,225 @@ > +/* > + * Copyright (C) 2015 Xilinx, Inc. > + * CEVA AHCI SATA platform driver > + * > + * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms and conditions of the GNU General Public License, > + * version 2, as published by the Free Software Foundation. > + * > + * This program is distributed in the hope it will be useful, but WITHOUT > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for > + * more details. > + * > + * You should have received a copy of the GNU General Public License along with > + * this program. If not, see <http://www.gnu.org/licenses/>. > + */ > + > +#include <linux/ahci_platform.h> > +#include <linux/kernel.h> > +#include <linux/libata.h> > +#include <linux/module.h> > +#include <linux/of_device.h> > +#include <linux/platform_device.h> > +#include "ahci.h" > + > +/* Vendor Specific Register Offsets */ > +#define AHCI_VEND_PCFG 0xA4 > +#define AHCI_VEND_PPCFG 0xA8 > +#define AHCI_VEND_PP2C 0xAC > +#define AHCI_VEND_PP3C 0xB0 > +#define AHCI_VEND_PP4C 0xB4 > +#define AHCI_VEND_PP5C 0xB8 > +#define AHCI_VEND_PAXIC 0xC0 > +#define AHCI_VEND_PTC 0xC8 > + > +/* Vendor Specific Register bit definitions */ > +#define PAXIC_ADBW_BW64 0x1 > +#define PAXIC_MAWIDD (1 << 8) > +#define PAXIC_MARIDD (1 << 16) > +#define PAXIC_OTL (0x4 << 20) > + > +#define PCFG_TPSS_VAL (0x32 << 16) > +#define PCFG_TPRS_VAL (0x2 << 12) > +#define PCFG_PAD_VAL 0x2 > + > +#define PPCFG_TTA 0x1FFFE > +#define PPCFG_PSSO_EN (1 << 28) > +#define PPCFG_PSS_EN (1 << 29) > +#define PPCFG_ESDF_EN (1 << 31) > + > +#define PP2C_CIBGMN 0x0F > +#define PP2C_CIBGMX (0x25 << 8) > +#define PP2C_CIBGN (0x18 << 16) > +#define PP2C_CINMP (0x29 << 24) > + > +#define PP3C_CWBGMN 0x04 > +#define PP3C_CWBGMX (0x0B << 8) > +#define PP3C_CWBGN (0x08 << 16) > +#define PP3C_CWNMP (0x0F << 24) > + > +#define PP4C_BMX 0x0a > +#define PP4C_BNM (0x08 << 8) > +#define PP4C_SFD (0x4a << 16) > +#define PP4C_PTST (0x06 << 24) > + > +#define PP5C_RIT 0x60216 > +#define PP5C_RCT (0x7f0 << 20) > + > +#define PTC_RX_WM_VAL 0x40 > +#define PTC_RSVD (1 << 27) > + > +#define PORT0_BASE 0x100 > +#define PORT1_BASE 0x180 > + > +/* Port Control Register Bit Definitions */ > +#define PORT_SCTL_SPD_GEN2 (0x2 << 4) > +#define PORT_SCTL_SPD_GEN1 (0x1 << 4) > +#define PORT_SCTL_IPM (0x3 << 8) > + > +#define PORT_BASE 0x100 > +#define PORT_OFFSET 0x80 > +#define NR_PORTS 2 > +#define DRV_NAME "ahci-ceva" > +#define CEVA_FLAG_BROKEN_GEN2 1 > + > +struct ceva_ahci_priv { > + struct platform_device *ahci_pdev; > + int flags; > +}; > + > +static struct ata_port_operations ahci_ceva_ops = { > + .inherits = &ahci_platform_ops, > +}; > + > +static const struct ata_port_info ahci_ceva_port_info = { > + .flags = AHCI_FLAG_COMMON, > + .pio_mask = ATA_PIO4, > + .udma_mask = ATA_UDMA6, > + .port_ops = &ahci_ceva_ops, > +}; > + > +static void ahci_ceva_setup(struct ahci_host_priv *hpriv) > +{ > + void __iomem *mmio = hpriv->mmio; > + struct ceva_ahci_priv *cevapriv = hpriv->plat_data; > + u32 tmp; > + int i; > + > + /* > + * AXI Data bus width to 64 > + * Set Mem Addr Read, Write ID for data transfers > + * Transfer limit to 72 DWord > + */ > + tmp = PAXIC_ADBW_BW64 | PAXIC_MAWIDD | PAXIC_MARIDD | PAXIC_OTL; > + writel(tmp, mmio + AHCI_VEND_PAXIC); > + > + /* Set AHCI Enable */ > + tmp = readl(mmio + HOST_CTL); > + tmp |= HOST_AHCI_EN; > + writel(tmp, mmio + HOST_CTL); > + > + for (i = 0; i < NR_PORTS; i++) { > + /* TPSS TPRS scalars, CISE and Port Addr */ > + tmp = PCFG_TPSS_VAL | PCFG_TPRS_VAL | (PCFG_PAD_VAL + i); > + writel(tmp, mmio + AHCI_VEND_PCFG); > + > + /* Port Phy Cfg register enables */ > + tmp = PPCFG_TTA | PPCFG_PSS_EN | PPCFG_ESDF_EN; > + writel(tmp, mmio + AHCI_VEND_PPCFG); > + > + /* Phy Control OOB timing parameters COMINIT */ > + tmp = PP2C_CIBGMN | PP2C_CIBGMX | PP2C_CIBGN | PP2C_CINMP; > + writel(tmp, mmio + AHCI_VEND_PP2C); > + > + /* Phy Control OOB timing parameters COMWAKE */ > + tmp = PP3C_CWBGMN | PP3C_CWBGMX | PP3C_CWBGN | PP3C_CWNMP; > + writel(tmp, mmio + AHCI_VEND_PP3C); > + > + /* Phy Control Burst timing setting */ > + tmp = PP4C_BMX | PP4C_BNM | PP4C_SFD | PP4C_PTST; > + writel(tmp, mmio + AHCI_VEND_PP4C); > + > + /* Rate Change Timer and Retry Interval Timer setting */ > + tmp = PP5C_RIT | PP5C_RCT; > + writel(tmp, mmio + AHCI_VEND_PP5C); > + > + /* Rx Watermark setting */ > + tmp = PTC_RX_WM_VAL | PTC_RSVD; > + writel(tmp, mmio + AHCI_VEND_PTC); > + > + /* Default to Gen 2 Speed and Gen 1 if Gen2 is broken */ > + tmp = PORT_SCTL_SPD_GEN2 | PORT_SCTL_IPM; > + if (cevapriv->flags & CEVA_FLAG_BROKEN_GEN2) > + tmp = PORT_SCTL_SPD_GEN1 | PORT_SCTL_IPM; > + writel(tmp, mmio + PORT_SCR_CTL + PORT_BASE + PORT_OFFSET * i); > + } > +} > + > +static struct scsi_host_template ahci_platform_sht = { > + AHCI_SHT(DRV_NAME), > +}; > + > +static int ceva_ahci_probe(struct platform_device *pdev) > +{ > + struct device_node *np = pdev->dev.of_node; > + struct device *dev = &pdev->dev; > + struct ahci_host_priv *hpriv; > + struct ceva_ahci_priv *cevapriv; > + > + cevapriv = devm_kzalloc(dev, sizeof(*cevapriv), GFP_KERNEL); > + if (!cevapriv) > + return -ENOMEM; > + > + cevapriv->ahci_pdev = pdev; > + > + hpriv = ahci_platform_get_resources(pdev); > + if (IS_ERR(hpriv)) > + return PTR_ERR(hpriv); > + > + if (of_property_read_bool(np, "ceva,broken-gen2")) > + cevapriv->flags = CEVA_FLAG_BROKEN_GEN2; > + > + hpriv->plat_data = cevapriv; > + > + /* CEVA specific initialization */ > + ahci_ceva_setup(hpriv); > + > + return ahci_platform_init_host(pdev, hpriv, &ahci_ceva_port_info, > + &ahci_platform_sht); > +} > + > +static int __maybe_unused ceva_ahci_suspend(struct device *dev) > +{ > + return ahci_platform_suspend_host(dev); > +} > + > +static int __maybe_unused ceva_ahci_resume(struct device *dev) > +{ > + return ahci_platform_resume_host(dev); > +} > + > +static SIMPLE_DEV_PM_OPS(ahci_ceva_pm_ops, ceva_ahci_suspend, ceva_ahci_resume); > + > +static const struct of_device_id ceva_ahci_of_match[] = { > + { .compatible = "ceva,ahci-1v84" }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, ceva_ahci_of_match); > + > +static struct platform_driver ceva_ahci_driver = { > + .probe = ceva_ahci_probe, > + .remove = ata_platform_remove_one, > + .driver = { > + .name = DRV_NAME, > + .of_match_table = ceva_ahci_of_match, > + .pm = &ahci_ceva_pm_ops, > + }, > +}; > +module_platform_driver(ceva_ahci_driver); > + > +MODULE_DESCRIPTION("CEVA AHCI SATA platform driver"); > +MODULE_AUTHOR("Xilinx Inc."); > +MODULE_LICENSE("GPL v2"); > -- > 2.1.2
Hi, On 09-06-15 07:27, Tejun Heo wrote: > cc'ing Hans and quoting whole message. > > Hans, can you please review this one? Done. I've one remark ceva_ahci_probe() is not calling ahci_platform_enable_resources() (and disable_resources again if the ahci_platform_init_host() fails). I guess that currently there are no clocks, regulators or phys defined in the dts? Note that the presence of regulators may very well be board dependent so you should really add these calls so that in the future dts files can have a regulator to control sata-device-power. Regards, Hans > > Thanks. > > On Fri, Jun 05, 2015 at 11:32:28AM +0530, Suneel Garapati wrote: >> Adds support for Ceva sata host controller on Xilinx >> Zynq UltraScale+ MPSoC. >> >> Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com> >> --- >> Changes v2 >> - Change module license string to GPL v2 >> --- >> drivers/ata/Kconfig | 9 ++ >> drivers/ata/Makefile | 1 + >> drivers/ata/ahci_ceva.c | 225 ++++++++++++++++++++++++++++++++++++++++++++++++ >> 3 files changed, 235 insertions(+) >> create mode 100644 drivers/ata/ahci_ceva.c >> >> diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig >> index b4524f4..6d17a3b 100644 >> --- a/drivers/ata/Kconfig >> +++ b/drivers/ata/Kconfig >> @@ -133,6 +133,15 @@ config AHCI_IMX >> >> If unsure, say N. >> >> +config AHCI_CEVA >> + tristate "CEVA AHCI SATA support" >> + depends on OF >> + help >> + This option enables support for the CEVA AHCI SATA. >> + It can be found on the Xilinx Zynq UltraScale+ MPSoC. >> + >> + If unsure, say N. >> + >> config AHCI_MVEBU >> tristate "Marvell EBU AHCI SATA support" >> depends on ARCH_MVEBU >> diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile >> index 5154753..af70919 100644 >> --- a/drivers/ata/Makefile >> +++ b/drivers/ata/Makefile >> @@ -11,6 +11,7 @@ obj-$(CONFIG_SATA_SIL24) += sata_sil24.o >> obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o >> obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o libahci.o >> obj-$(CONFIG_AHCI_BRCMSTB) += ahci_brcmstb.o libahci.o libahci_platform.o >> +obj-$(CONFIG_AHCI_CEVA) += ahci_ceva.o libahci.o libahci_platform.o >> obj-$(CONFIG_AHCI_DA850) += ahci_da850.o libahci.o libahci_platform.o >> obj-$(CONFIG_AHCI_IMX) += ahci_imx.o libahci.o libahci_platform.o >> obj-$(CONFIG_AHCI_MVEBU) += ahci_mvebu.o libahci.o libahci_platform.o >> diff --git a/drivers/ata/ahci_ceva.c b/drivers/ata/ahci_ceva.c >> new file mode 100644 >> index 0000000..559d960 >> --- /dev/null >> +++ b/drivers/ata/ahci_ceva.c >> @@ -0,0 +1,225 @@ >> +/* >> + * Copyright (C) 2015 Xilinx, Inc. >> + * CEVA AHCI SATA platform driver >> + * >> + * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov >> + * >> + * This program is free software; you can redistribute it and/or modify it >> + * under the terms and conditions of the GNU General Public License, >> + * version 2, as published by the Free Software Foundation. >> + * >> + * This program is distributed in the hope it will be useful, but WITHOUT >> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or >> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for >> + * more details. >> + * >> + * You should have received a copy of the GNU General Public License along with >> + * this program. If not, see <http://www.gnu.org/licenses/>. >> + */ >> + >> +#include <linux/ahci_platform.h> >> +#include <linux/kernel.h> >> +#include <linux/libata.h> >> +#include <linux/module.h> >> +#include <linux/of_device.h> >> +#include <linux/platform_device.h> >> +#include "ahci.h" >> + >> +/* Vendor Specific Register Offsets */ >> +#define AHCI_VEND_PCFG 0xA4 >> +#define AHCI_VEND_PPCFG 0xA8 >> +#define AHCI_VEND_PP2C 0xAC >> +#define AHCI_VEND_PP3C 0xB0 >> +#define AHCI_VEND_PP4C 0xB4 >> +#define AHCI_VEND_PP5C 0xB8 >> +#define AHCI_VEND_PAXIC 0xC0 >> +#define AHCI_VEND_PTC 0xC8 >> + >> +/* Vendor Specific Register bit definitions */ >> +#define PAXIC_ADBW_BW64 0x1 >> +#define PAXIC_MAWIDD (1 << 8) >> +#define PAXIC_MARIDD (1 << 16) >> +#define PAXIC_OTL (0x4 << 20) >> + >> +#define PCFG_TPSS_VAL (0x32 << 16) >> +#define PCFG_TPRS_VAL (0x2 << 12) >> +#define PCFG_PAD_VAL 0x2 >> + >> +#define PPCFG_TTA 0x1FFFE >> +#define PPCFG_PSSO_EN (1 << 28) >> +#define PPCFG_PSS_EN (1 << 29) >> +#define PPCFG_ESDF_EN (1 << 31) >> + >> +#define PP2C_CIBGMN 0x0F >> +#define PP2C_CIBGMX (0x25 << 8) >> +#define PP2C_CIBGN (0x18 << 16) >> +#define PP2C_CINMP (0x29 << 24) >> + >> +#define PP3C_CWBGMN 0x04 >> +#define PP3C_CWBGMX (0x0B << 8) >> +#define PP3C_CWBGN (0x08 << 16) >> +#define PP3C_CWNMP (0x0F << 24) >> + >> +#define PP4C_BMX 0x0a >> +#define PP4C_BNM (0x08 << 8) >> +#define PP4C_SFD (0x4a << 16) >> +#define PP4C_PTST (0x06 << 24) >> + >> +#define PP5C_RIT 0x60216 >> +#define PP5C_RCT (0x7f0 << 20) >> + >> +#define PTC_RX_WM_VAL 0x40 >> +#define PTC_RSVD (1 << 27) >> + >> +#define PORT0_BASE 0x100 >> +#define PORT1_BASE 0x180 >> + >> +/* Port Control Register Bit Definitions */ >> +#define PORT_SCTL_SPD_GEN2 (0x2 << 4) >> +#define PORT_SCTL_SPD_GEN1 (0x1 << 4) >> +#define PORT_SCTL_IPM (0x3 << 8) >> + >> +#define PORT_BASE 0x100 >> +#define PORT_OFFSET 0x80 >> +#define NR_PORTS 2 >> +#define DRV_NAME "ahci-ceva" >> +#define CEVA_FLAG_BROKEN_GEN2 1 >> + >> +struct ceva_ahci_priv { >> + struct platform_device *ahci_pdev; >> + int flags; >> +}; >> + >> +static struct ata_port_operations ahci_ceva_ops = { >> + .inherits = &ahci_platform_ops, >> +}; >> + >> +static const struct ata_port_info ahci_ceva_port_info = { >> + .flags = AHCI_FLAG_COMMON, >> + .pio_mask = ATA_PIO4, >> + .udma_mask = ATA_UDMA6, >> + .port_ops = &ahci_ceva_ops, >> +}; >> + >> +static void ahci_ceva_setup(struct ahci_host_priv *hpriv) >> +{ >> + void __iomem *mmio = hpriv->mmio; >> + struct ceva_ahci_priv *cevapriv = hpriv->plat_data; >> + u32 tmp; >> + int i; >> + >> + /* >> + * AXI Data bus width to 64 >> + * Set Mem Addr Read, Write ID for data transfers >> + * Transfer limit to 72 DWord >> + */ >> + tmp = PAXIC_ADBW_BW64 | PAXIC_MAWIDD | PAXIC_MARIDD | PAXIC_OTL; >> + writel(tmp, mmio + AHCI_VEND_PAXIC); >> + >> + /* Set AHCI Enable */ >> + tmp = readl(mmio + HOST_CTL); >> + tmp |= HOST_AHCI_EN; >> + writel(tmp, mmio + HOST_CTL); >> + >> + for (i = 0; i < NR_PORTS; i++) { >> + /* TPSS TPRS scalars, CISE and Port Addr */ >> + tmp = PCFG_TPSS_VAL | PCFG_TPRS_VAL | (PCFG_PAD_VAL + i); >> + writel(tmp, mmio + AHCI_VEND_PCFG); >> + >> + /* Port Phy Cfg register enables */ >> + tmp = PPCFG_TTA | PPCFG_PSS_EN | PPCFG_ESDF_EN; >> + writel(tmp, mmio + AHCI_VEND_PPCFG); >> + >> + /* Phy Control OOB timing parameters COMINIT */ >> + tmp = PP2C_CIBGMN | PP2C_CIBGMX | PP2C_CIBGN | PP2C_CINMP; >> + writel(tmp, mmio + AHCI_VEND_PP2C); >> + >> + /* Phy Control OOB timing parameters COMWAKE */ >> + tmp = PP3C_CWBGMN | PP3C_CWBGMX | PP3C_CWBGN | PP3C_CWNMP; >> + writel(tmp, mmio + AHCI_VEND_PP3C); >> + >> + /* Phy Control Burst timing setting */ >> + tmp = PP4C_BMX | PP4C_BNM | PP4C_SFD | PP4C_PTST; >> + writel(tmp, mmio + AHCI_VEND_PP4C); >> + >> + /* Rate Change Timer and Retry Interval Timer setting */ >> + tmp = PP5C_RIT | PP5C_RCT; >> + writel(tmp, mmio + AHCI_VEND_PP5C); >> + >> + /* Rx Watermark setting */ >> + tmp = PTC_RX_WM_VAL | PTC_RSVD; >> + writel(tmp, mmio + AHCI_VEND_PTC); >> + >> + /* Default to Gen 2 Speed and Gen 1 if Gen2 is broken */ >> + tmp = PORT_SCTL_SPD_GEN2 | PORT_SCTL_IPM; >> + if (cevapriv->flags & CEVA_FLAG_BROKEN_GEN2) >> + tmp = PORT_SCTL_SPD_GEN1 | PORT_SCTL_IPM; >> + writel(tmp, mmio + PORT_SCR_CTL + PORT_BASE + PORT_OFFSET * i); >> + } >> +} >> + >> +static struct scsi_host_template ahci_platform_sht = { >> + AHCI_SHT(DRV_NAME), >> +}; >> + >> +static int ceva_ahci_probe(struct platform_device *pdev) >> +{ >> + struct device_node *np = pdev->dev.of_node; >> + struct device *dev = &pdev->dev; >> + struct ahci_host_priv *hpriv; >> + struct ceva_ahci_priv *cevapriv; >> + >> + cevapriv = devm_kzalloc(dev, sizeof(*cevapriv), GFP_KERNEL); >> + if (!cevapriv) >> + return -ENOMEM; >> + >> + cevapriv->ahci_pdev = pdev; >> + >> + hpriv = ahci_platform_get_resources(pdev); >> + if (IS_ERR(hpriv)) >> + return PTR_ERR(hpriv); >> + >> + if (of_property_read_bool(np, "ceva,broken-gen2")) >> + cevapriv->flags = CEVA_FLAG_BROKEN_GEN2; >> + >> + hpriv->plat_data = cevapriv; >> + >> + /* CEVA specific initialization */ >> + ahci_ceva_setup(hpriv); >> + >> + return ahci_platform_init_host(pdev, hpriv, &ahci_ceva_port_info, >> + &ahci_platform_sht); >> +} >> + >> +static int __maybe_unused ceva_ahci_suspend(struct device *dev) >> +{ >> + return ahci_platform_suspend_host(dev); >> +} >> + >> +static int __maybe_unused ceva_ahci_resume(struct device *dev) >> +{ >> + return ahci_platform_resume_host(dev); >> +} >> + >> +static SIMPLE_DEV_PM_OPS(ahci_ceva_pm_ops, ceva_ahci_suspend, ceva_ahci_resume); >> + >> +static const struct of_device_id ceva_ahci_of_match[] = { >> + { .compatible = "ceva,ahci-1v84" }, >> + {}, >> +}; >> +MODULE_DEVICE_TABLE(of, ceva_ahci_of_match); >> + >> +static struct platform_driver ceva_ahci_driver = { >> + .probe = ceva_ahci_probe, >> + .remove = ata_platform_remove_one, >> + .driver = { >> + .name = DRV_NAME, >> + .of_match_table = ceva_ahci_of_match, >> + .pm = &ahci_ceva_pm_ops, >> + }, >> +}; >> +module_platform_driver(ceva_ahci_driver); >> + >> +MODULE_DESCRIPTION("CEVA AHCI SATA platform driver"); >> +MODULE_AUTHOR("Xilinx Inc."); >> +MODULE_LICENSE("GPL v2"); >> -- >> 2.1.2 > -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig index b4524f4..6d17a3b 100644 --- a/drivers/ata/Kconfig +++ b/drivers/ata/Kconfig @@ -133,6 +133,15 @@ config AHCI_IMX If unsure, say N. +config AHCI_CEVA + tristate "CEVA AHCI SATA support" + depends on OF + help + This option enables support for the CEVA AHCI SATA. + It can be found on the Xilinx Zynq UltraScale+ MPSoC. + + If unsure, say N. + config AHCI_MVEBU tristate "Marvell EBU AHCI SATA support" depends on ARCH_MVEBU diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile index 5154753..af70919 100644 --- a/drivers/ata/Makefile +++ b/drivers/ata/Makefile @@ -11,6 +11,7 @@ obj-$(CONFIG_SATA_SIL24) += sata_sil24.o obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o libahci.o obj-$(CONFIG_AHCI_BRCMSTB) += ahci_brcmstb.o libahci.o libahci_platform.o +obj-$(CONFIG_AHCI_CEVA) += ahci_ceva.o libahci.o libahci_platform.o obj-$(CONFIG_AHCI_DA850) += ahci_da850.o libahci.o libahci_platform.o obj-$(CONFIG_AHCI_IMX) += ahci_imx.o libahci.o libahci_platform.o obj-$(CONFIG_AHCI_MVEBU) += ahci_mvebu.o libahci.o libahci_platform.o diff --git a/drivers/ata/ahci_ceva.c b/drivers/ata/ahci_ceva.c new file mode 100644 index 0000000..559d960 --- /dev/null +++ b/drivers/ata/ahci_ceva.c @@ -0,0 +1,225 @@ +/* + * Copyright (C) 2015 Xilinx, Inc. + * CEVA AHCI SATA platform driver + * + * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/ahci_platform.h> +#include <linux/kernel.h> +#include <linux/libata.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include "ahci.h" + +/* Vendor Specific Register Offsets */ +#define AHCI_VEND_PCFG 0xA4 +#define AHCI_VEND_PPCFG 0xA8 +#define AHCI_VEND_PP2C 0xAC +#define AHCI_VEND_PP3C 0xB0 +#define AHCI_VEND_PP4C 0xB4 +#define AHCI_VEND_PP5C 0xB8 +#define AHCI_VEND_PAXIC 0xC0 +#define AHCI_VEND_PTC 0xC8 + +/* Vendor Specific Register bit definitions */ +#define PAXIC_ADBW_BW64 0x1 +#define PAXIC_MAWIDD (1 << 8) +#define PAXIC_MARIDD (1 << 16) +#define PAXIC_OTL (0x4 << 20) + +#define PCFG_TPSS_VAL (0x32 << 16) +#define PCFG_TPRS_VAL (0x2 << 12) +#define PCFG_PAD_VAL 0x2 + +#define PPCFG_TTA 0x1FFFE +#define PPCFG_PSSO_EN (1 << 28) +#define PPCFG_PSS_EN (1 << 29) +#define PPCFG_ESDF_EN (1 << 31) + +#define PP2C_CIBGMN 0x0F +#define PP2C_CIBGMX (0x25 << 8) +#define PP2C_CIBGN (0x18 << 16) +#define PP2C_CINMP (0x29 << 24) + +#define PP3C_CWBGMN 0x04 +#define PP3C_CWBGMX (0x0B << 8) +#define PP3C_CWBGN (0x08 << 16) +#define PP3C_CWNMP (0x0F << 24) + +#define PP4C_BMX 0x0a +#define PP4C_BNM (0x08 << 8) +#define PP4C_SFD (0x4a << 16) +#define PP4C_PTST (0x06 << 24) + +#define PP5C_RIT 0x60216 +#define PP5C_RCT (0x7f0 << 20) + +#define PTC_RX_WM_VAL 0x40 +#define PTC_RSVD (1 << 27) + +#define PORT0_BASE 0x100 +#define PORT1_BASE 0x180 + +/* Port Control Register Bit Definitions */ +#define PORT_SCTL_SPD_GEN2 (0x2 << 4) +#define PORT_SCTL_SPD_GEN1 (0x1 << 4) +#define PORT_SCTL_IPM (0x3 << 8) + +#define PORT_BASE 0x100 +#define PORT_OFFSET 0x80 +#define NR_PORTS 2 +#define DRV_NAME "ahci-ceva" +#define CEVA_FLAG_BROKEN_GEN2 1 + +struct ceva_ahci_priv { + struct platform_device *ahci_pdev; + int flags; +}; + +static struct ata_port_operations ahci_ceva_ops = { + .inherits = &ahci_platform_ops, +}; + +static const struct ata_port_info ahci_ceva_port_info = { + .flags = AHCI_FLAG_COMMON, + .pio_mask = ATA_PIO4, + .udma_mask = ATA_UDMA6, + .port_ops = &ahci_ceva_ops, +}; + +static void ahci_ceva_setup(struct ahci_host_priv *hpriv) +{ + void __iomem *mmio = hpriv->mmio; + struct ceva_ahci_priv *cevapriv = hpriv->plat_data; + u32 tmp; + int i; + + /* + * AXI Data bus width to 64 + * Set Mem Addr Read, Write ID for data transfers + * Transfer limit to 72 DWord + */ + tmp = PAXIC_ADBW_BW64 | PAXIC_MAWIDD | PAXIC_MARIDD | PAXIC_OTL; + writel(tmp, mmio + AHCI_VEND_PAXIC); + + /* Set AHCI Enable */ + tmp = readl(mmio + HOST_CTL); + tmp |= HOST_AHCI_EN; + writel(tmp, mmio + HOST_CTL); + + for (i = 0; i < NR_PORTS; i++) { + /* TPSS TPRS scalars, CISE and Port Addr */ + tmp = PCFG_TPSS_VAL | PCFG_TPRS_VAL | (PCFG_PAD_VAL + i); + writel(tmp, mmio + AHCI_VEND_PCFG); + + /* Port Phy Cfg register enables */ + tmp = PPCFG_TTA | PPCFG_PSS_EN | PPCFG_ESDF_EN; + writel(tmp, mmio + AHCI_VEND_PPCFG); + + /* Phy Control OOB timing parameters COMINIT */ + tmp = PP2C_CIBGMN | PP2C_CIBGMX | PP2C_CIBGN | PP2C_CINMP; + writel(tmp, mmio + AHCI_VEND_PP2C); + + /* Phy Control OOB timing parameters COMWAKE */ + tmp = PP3C_CWBGMN | PP3C_CWBGMX | PP3C_CWBGN | PP3C_CWNMP; + writel(tmp, mmio + AHCI_VEND_PP3C); + + /* Phy Control Burst timing setting */ + tmp = PP4C_BMX | PP4C_BNM | PP4C_SFD | PP4C_PTST; + writel(tmp, mmio + AHCI_VEND_PP4C); + + /* Rate Change Timer and Retry Interval Timer setting */ + tmp = PP5C_RIT | PP5C_RCT; + writel(tmp, mmio + AHCI_VEND_PP5C); + + /* Rx Watermark setting */ + tmp = PTC_RX_WM_VAL | PTC_RSVD; + writel(tmp, mmio + AHCI_VEND_PTC); + + /* Default to Gen 2 Speed and Gen 1 if Gen2 is broken */ + tmp = PORT_SCTL_SPD_GEN2 | PORT_SCTL_IPM; + if (cevapriv->flags & CEVA_FLAG_BROKEN_GEN2) + tmp = PORT_SCTL_SPD_GEN1 | PORT_SCTL_IPM; + writel(tmp, mmio + PORT_SCR_CTL + PORT_BASE + PORT_OFFSET * i); + } +} + +static struct scsi_host_template ahci_platform_sht = { + AHCI_SHT(DRV_NAME), +}; + +static int ceva_ahci_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct device *dev = &pdev->dev; + struct ahci_host_priv *hpriv; + struct ceva_ahci_priv *cevapriv; + + cevapriv = devm_kzalloc(dev, sizeof(*cevapriv), GFP_KERNEL); + if (!cevapriv) + return -ENOMEM; + + cevapriv->ahci_pdev = pdev; + + hpriv = ahci_platform_get_resources(pdev); + if (IS_ERR(hpriv)) + return PTR_ERR(hpriv); + + if (of_property_read_bool(np, "ceva,broken-gen2")) + cevapriv->flags = CEVA_FLAG_BROKEN_GEN2; + + hpriv->plat_data = cevapriv; + + /* CEVA specific initialization */ + ahci_ceva_setup(hpriv); + + return ahci_platform_init_host(pdev, hpriv, &ahci_ceva_port_info, + &ahci_platform_sht); +} + +static int __maybe_unused ceva_ahci_suspend(struct device *dev) +{ + return ahci_platform_suspend_host(dev); +} + +static int __maybe_unused ceva_ahci_resume(struct device *dev) +{ + return ahci_platform_resume_host(dev); +} + +static SIMPLE_DEV_PM_OPS(ahci_ceva_pm_ops, ceva_ahci_suspend, ceva_ahci_resume); + +static const struct of_device_id ceva_ahci_of_match[] = { + { .compatible = "ceva,ahci-1v84" }, + {}, +}; +MODULE_DEVICE_TABLE(of, ceva_ahci_of_match); + +static struct platform_driver ceva_ahci_driver = { + .probe = ceva_ahci_probe, + .remove = ata_platform_remove_one, + .driver = { + .name = DRV_NAME, + .of_match_table = ceva_ahci_of_match, + .pm = &ahci_ceva_pm_ops, + }, +}; +module_platform_driver(ceva_ahci_driver); + +MODULE_DESCRIPTION("CEVA AHCI SATA platform driver"); +MODULE_AUTHOR("Xilinx Inc."); +MODULE_LICENSE("GPL v2");
Adds support for Ceva sata host controller on Xilinx Zynq UltraScale+ MPSoC. Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com> --- Changes v2 - Change module license string to GPL v2 --- drivers/ata/Kconfig | 9 ++ drivers/ata/Makefile | 1 + drivers/ata/ahci_ceva.c | 225 ++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 235 insertions(+) create mode 100644 drivers/ata/ahci_ceva.c -- 2.1.2 -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html