diff mbox

[U-Boot,1/5] tbs2910: support for usb otg host mode

Message ID 1430860162-24034-1-git-send-email-smoch@web.de
State Awaiting Upstream
Delegated to: Stefano Babic
Headers show

Commit Message

Sören Moch May 5, 2015, 9:09 p.m. UTC 
Add support for USB OTG host mode. Only high speed devices supported so far
(e.g. usb 2.0 hub required to connect a keyboard).

Signed-off-by: Soeren Moch <smoch@web.de>
---
Cc: Stefano Babic <sbabic@denx.de>
---
 board/tbs/tbs2910/tbs2910.c | 10 ++++++++++
 include/configs/tbs2910.h   |  1 +
 2 files changed, 11 insertions(+)

Comments

Stefano Babic May 15, 2015, 1:06 p.m. UTC | #1 
On 05/05/2015 23:09, Soeren Moch wrote:
> Add support for USB OTG host mode. Only high speed devices supported so far
> (e.g. usb 2.0 hub required to connect a keyboard).
> 
> Signed-off-by: Soeren Moch <smoch@web.de>
> ---
> Cc: Stefano Babic <sbabic@denx.de>
> ---

Applied to u-boot-imx, thanks !

Best regards,
     Stefano Babic
diff mbox

Patch

diff --git a/board/tbs/tbs2910/tbs2910.c b/board/tbs/tbs2910/tbs2910.c
index 42b166d..0b509b6 100644
--- a/board/tbs/tbs2910/tbs2910.c
+++ b/board/tbs/tbs2910/tbs2910.c
@@ -372,6 +372,12 @@  static const struct boot_mode board_boot_modes[] = {
 };
 #endif
 
+#ifdef CONFIG_USB_EHCI_MX6
+static iomux_v3_cfg_t const usb_otg_pads[] = {
+	MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+#endif
+
 int board_init(void)
 {
 	/* address of boot parameters */
@@ -391,6 +397,10 @@  int board_init(void)
 #ifdef CONFIG_CMD_BMODE
 	add_board_boot_modes(board_boot_modes);
 #endif
+#ifdef CONFIG_USB_EHCI_MX6
+	imx_iomux_v3_setup_multiple_pads(
+		usb_otg_pads, ARRAY_SIZE(usb_otg_pads));
+#endif
 	return 0;
 }
 
diff --git a/include/configs/tbs2910.h b/include/configs/tbs2910.h
index 7089378..e5828e0 100644
--- a/include/configs/tbs2910.h
+++ b/include/configs/tbs2910.h
@@ -163,6 +163,7 @@ 
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_MX6
 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
 #define CONFIG_USB_STORAGE
 #define CONFIG_CMD_USB_MASS_STORAGE