new file mode 100644
@@ -0,0 +1,3119 @@
+/*
+ * This file is part of the Chelsio T4 Ethernet driver for Linux.
+ *
+ * Copyright (c) 2003-2010 Chelsio Communications, Inc. All rights reserved.
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the
+ * OpenIB.org BSD license below:
+ *
+ * Redistribution and use in source and binary forms, with or
+ * without modification, are permitted provided that the following
+ * conditions are met:
+ *
+ * - Redistributions of source code must retain the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer.
+ *
+ * - Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials
+ * provided with the distribution.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
+ * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
+ * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+ * SOFTWARE.
+ */
+
+#include <linux/init.h>
+#include <linux/delay.h>
+#include "cxgb4.h"
+#include "t4_regs.h"
+#include "t4fw_api.h"
+
+/**
+ * t4_wait_op_done_val - wait until an operation is completed
+ * @adapter: the adapter performing the operation
+ * @reg: the register to check for completion
+ * @mask: a single-bit field within @reg that indicates completion
+ * @polarity: the value of the field when the operation is completed
+ * @attempts: number of check iterations
+ * @delay: delay in usecs between iterations
+ * @valp: where to store the value of the register at completion time
+ *
+ * Wait until an operation is completed by checking a bit in a register
+ * up to @attempts times. If @valp is not NULL the value of the register
+ * at the time it indicated completion is stored there. Returns 0 if the
+ * operation completes and -EAGAIN otherwise.
+ */
+int t4_wait_op_done_val(struct adapter *adapter, int reg, u32 mask,
+ int polarity, int attempts, int delay, u32 *valp)
+{
+ while (1) {
+ u32 val = t4_read_reg(adapter, reg);
+
+ if (!!(val & mask) == polarity) {
+ if (valp)
+ *valp = val;
+ return 0;
+ }
+ if (--attempts == 0)
+ return -EAGAIN;
+ if (delay)
+ udelay(delay);
+ }
+}
+
+static inline int t4_wait_op_done(struct adapter *adapter, int reg, u32 mask,
+ int polarity, int attempts, int delay)
+{
+ return t4_wait_op_done_val(adapter, reg, mask, polarity, attempts,
+ delay, NULL);
+}
+
+/**
+ * t4_set_reg_field - set a register field to a value
+ * @adapter: the adapter to program
+ * @addr: the register address
+ * @mask: specifies the portion of the register to modify
+ * @val: the new value for the register field
+ *
+ * Sets a register field specified by the supplied mask to the
+ * given value.
+ */
+void t4_set_reg_field(struct adapter *adapter, unsigned int addr, u32 mask,
+ u32 val)
+{
+ u32 v = t4_read_reg(adapter, addr) & ~mask;
+
+ t4_write_reg(adapter, addr, v | val);
+ (void) t4_read_reg(adapter, addr); /* flush */
+}
+
+/**
+ * t4_read_indirect - read indirectly addressed registers
+ * @adap: the adapter
+ * @addr_reg: register holding the indirect address
+ * @data_reg: register holding the value of the indirect register
+ * @vals: where the read register values are stored
+ * @nregs: how many indirect registers to read
+ * @start_idx: index of first indirect register to read
+ *
+ * Reads registers that are accessed indirectly through an address/data
+ * register pair.
+ */
+void t4_read_indirect(struct adapter *adap, unsigned int addr_reg,
+ unsigned int data_reg, u32 *vals, unsigned int nregs,
+ unsigned int start_idx)
+{
+ while (nregs--) {
+ t4_write_reg(adap, addr_reg, start_idx);
+ *vals++ = t4_read_reg(adap, data_reg);
+ start_idx++;
+ }
+}
+
+/**
+ * t4_write_indirect - write indirectly addressed registers
+ * @adap: the adapter
+ * @addr_reg: register holding the indirect addresses
+ * @data_reg: register holding the value for the indirect registers
+ * @vals: values to write
+ * @nregs: how many indirect registers to write
+ * @start_idx: address of first indirect register to write
+ *
+ * Writes a sequential block of registers that are accessed indirectly
+ * through an address/data register pair.
+ */
+void t4_write_indirect(struct adapter *adap, unsigned int addr_reg,
+ unsigned int data_reg, const u32 *vals,
+ unsigned int nregs, unsigned int start_idx)
+{
+ while (nregs--) {
+ t4_write_reg(adap, addr_reg, start_idx++);
+ t4_write_reg(adap, data_reg, *vals++);
+ }
+}
+
+/*
+ * Get the reply to a mailbox command and store it in @rpl in big-endian order.
+ */
+static void get_mbox_rpl(struct adapter *adap, __be64 *rpl, int nflit,
+ u32 mbox_addr)
+{
+ for ( ; nflit; nflit--, mbox_addr += 8)
+ *rpl++ = cpu_to_be64(t4_read_reg64(adap, mbox_addr));
+}
+
+/*
+ * Handle a FW assertion reported in a mailbox.
+ */
+static void fw_asrt(struct adapter *adap, u32 mbox_addr)
+{
+ struct fw_debug_cmd asrt;
+
+ get_mbox_rpl(adap, (__be64 *)&asrt, sizeof(asrt) / 8, mbox_addr);
+ dev_alert(adap->pdev_dev,
+ "FW assertion at %.16s:%u, val0 %#x, val1 %#x\n",
+ asrt.u.assert.filename_0_7, ntohl(asrt.u.assert.line),
+ ntohl(asrt.u.assert.x), ntohl(asrt.u.assert.y));
+}
+
+static void dump_mbox(struct adapter *adap, int mbox, u32 data_reg)
+{
+ dev_err(adap->pdev_dev,
+ "mbox %d: %llx %llx %llx %llx %llx %llx %llx %llx\n", mbox,
+ (unsigned long long)t4_read_reg64(adap, data_reg),
+ (unsigned long long)t4_read_reg64(adap, data_reg + 8),
+ (unsigned long long)t4_read_reg64(adap, data_reg + 16),
+ (unsigned long long)t4_read_reg64(adap, data_reg + 24),
+ (unsigned long long)t4_read_reg64(adap, data_reg + 32),
+ (unsigned long long)t4_read_reg64(adap, data_reg + 40),
+ (unsigned long long)t4_read_reg64(adap, data_reg + 48),
+ (unsigned long long)t4_read_reg64(adap, data_reg + 56));
+}
+
+/**
+ * t4_wr_mbox_meat - send a command to FW through the given mailbox
+ * @adap: the adapter
+ * @mbox: index of the mailbox to use
+ * @cmd: the command to write
+ * @size: command length in bytes
+ * @rpl: where to optionally store the reply
+ * @sleep_ok: if true we may sleep while awaiting command completion
+ *
+ * Sends the given command to FW through the selected mailbox and waits
+ * for the FW to execute the command. If @rpl is not %NULL it is used to
+ * store the FW's reply to the command. The command and its optional
+ * reply are of the same length. FW can take up to %FW_CMD_MAX_TIMEOUT ms
+ * to respond. @sleep_ok determines whether we may sleep while awaiting
+ * the response. If sleeping is allowed we use progressive backoff
+ * otherwise we spin.
+ *
+ * The return value is 0 on success or a negative errno on failure. A
+ * failure can happen either because we are not able to execute the
+ * command or FW executes it but signals an error. In the latter case
+ * the return value is the error code indicated by FW (negated).
+ */
+int t4_wr_mbox_meat(struct adapter *adap, int mbox, const void *cmd, int size,
+ void *rpl, bool sleep_ok)
+{
+ static int delay[] = {
+ 1, 1, 3, 5, 10, 10, 20, 50, 100, 200
+ };
+
+ u32 v;
+ u64 res;
+ int i, ms, delay_idx;
+ const __be64 *p = cmd;
+ u32 data_reg = PF_REG(mbox, CIM_PF_MAILBOX_DATA);
+ u32 ctl_reg = PF_REG(mbox, CIM_PF_MAILBOX_CTRL);
+
+ if ((size & 15) || size > MBOX_LEN)
+ return -EINVAL;
+
+ v = MBOWNER_GET(t4_read_reg(adap, ctl_reg));
+ for (i = 0; v == MBOX_OWNER_NONE && i < 3; i++)
+ v = MBOWNER_GET(t4_read_reg(adap, ctl_reg));
+
+ if (v != MBOX_OWNER_DRV)
+ return v ? -EBUSY : -ETIMEDOUT;
+
+ for (i = 0; i < size; i += 8)
+ t4_write_reg64(adap, data_reg + i, be64_to_cpu(*p++));
+
+ t4_write_reg(adap, ctl_reg, MBMSGVALID | MBOWNER(MBOX_OWNER_FW));
+ t4_read_reg(adap, ctl_reg); /* flush write */
+
+ delay_idx = 0;
+ ms = delay[0];
+
+ for (i = 0; i < FW_CMD_MAX_TIMEOUT; i += ms) {
+ if (sleep_ok) {
+ ms = delay[delay_idx]; /* last element may repeat */
+ if (delay_idx < ARRAY_SIZE(delay) - 1)
+ delay_idx++;
+ msleep(ms);
+ } else
+ mdelay(ms);
+
+ v = t4_read_reg(adap, ctl_reg);
+ if (MBOWNER_GET(v) == MBOX_OWNER_DRV) {
+ if (!(v & MBMSGVALID)) {
+ t4_write_reg(adap, ctl_reg, 0);
+ continue;
+ }
+
+ res = t4_read_reg64(adap, data_reg);
+ if (FW_CMD_OP_GET(res >> 32) == FW_DEBUG_CMD) {
+ fw_asrt(adap, data_reg);
+ res = FW_CMD_RETVAL(EIO);
+ } else if (rpl)
+ get_mbox_rpl(adap, rpl, size / 8, data_reg);
+
+ if (FW_CMD_RETVAL_GET((int)res))
+ dump_mbox(adap, mbox, data_reg);
+ t4_write_reg(adap, ctl_reg, 0);
+ return -FW_CMD_RETVAL_GET((int)res);
+ }
+ }
+
+ dump_mbox(adap, mbox, data_reg);
+ dev_err(adap->pdev_dev, "command %#x in mailbox %d timed out\n",
+ *(const u8 *)cmd, mbox);
+ return -ETIMEDOUT;
+}
+
+/**
+ * t4_mc_read - read from MC through backdoor accesses
+ * @adap: the adapter
+ * @addr: address of first byte requested
+ * @data: 64 bytes of data containing the requested address
+ * @ecc: where to store the corresponding 64-bit ECC word
+ *
+ * Read 64 bytes of data from MC starting at a 64-byte-aligned address
+ * that covers the requested address @addr. If @parity is not %NULL it
+ * is assigned the 64-bit ECC word for the read data.
+ */
+int t4_mc_read(struct adapter *adap, u32 addr, __be32 *data, u64 *ecc)
+{
+ int i;
+
+ if (t4_read_reg(adap, MC_BIST_CMD) & START_BIST)
+ return -EBUSY;
+ t4_write_reg(adap, MC_BIST_CMD_ADDR, addr & ~0x3fU);
+ t4_write_reg(adap, MC_BIST_CMD_LEN, 64);
+ t4_write_reg(adap, MC_BIST_DATA_PATTERN, 0xc);
+ t4_write_reg(adap, MC_BIST_CMD, BIST_OPCODE(1) | START_BIST |
+ BIST_CMD_GAP(1));
+ i = t4_wait_op_done(adap, MC_BIST_CMD, START_BIST, 0, 10, 1);
+ if (i)
+ return i;
+
+#define MC_DATA(i) MC_BIST_STATUS_REG(MC_BIST_STATUS_RDATA, i)
+
+ for (i = 15; i >= 0; i--)
+ *data++ = htonl(t4_read_reg(adap, MC_DATA(i)));
+ if (ecc)
+ *ecc = t4_read_reg64(adap, MC_DATA(16));
+#undef MC_DATA
+ return 0;
+}
+
+/**
+ * t4_edc_read - read from EDC through backdoor accesses
+ * @adap: the adapter
+ * @idx: which EDC to access
+ * @addr: address of first byte requested
+ * @data: 64 bytes of data containing the requested address
+ * @ecc: where to store the corresponding 64-bit ECC word
+ *
+ * Read 64 bytes of data from EDC starting at a 64-byte-aligned address
+ * that covers the requested address @addr. If @parity is not %NULL it
+ * is assigned the 64-bit ECC word for the read data.
+ */
+int t4_edc_read(struct adapter *adap, int idx, u32 addr, __be32 *data, u64 *ecc)
+{
+ int i;
+
+ idx *= EDC_STRIDE;
+ if (t4_read_reg(adap, EDC_BIST_CMD + idx) & START_BIST)
+ return -EBUSY;
+ t4_write_reg(adap, EDC_BIST_CMD_ADDR + idx, addr & ~0x3fU);
+ t4_write_reg(adap, EDC_BIST_CMD_LEN + idx, 64);
+ t4_write_reg(adap, EDC_BIST_DATA_PATTERN + idx, 0xc);
+ t4_write_reg(adap, EDC_BIST_CMD + idx,
+ BIST_OPCODE(1) | BIST_CMD_GAP(1) | START_BIST);
+ i = t4_wait_op_done(adap, EDC_BIST_CMD + idx, START_BIST, 0, 10, 1);
+ if (i)
+ return i;
+
+#define EDC_DATA(i) (EDC_BIST_STATUS_REG(EDC_BIST_STATUS_RDATA, i) + idx)
+
+ for (i = 15; i >= 0; i--)
+ *data++ = htonl(t4_read_reg(adap, EDC_DATA(i)));
+ if (ecc)
+ *ecc = t4_read_reg64(adap, EDC_DATA(16));
+#undef EDC_DATA
+ return 0;
+}
+
+#define VPD_ENTRY(name, len) \
+ u8 name##_kword[2]; u8 name##_len; u8 name##_data[len]
+
+/*
+ * Partial EEPROM Vital Product Data structure. Includes only the ID and
+ * VPD-R sections.
+ */
+struct t4_vpd {
+ u8 id_tag;
+ u8 id_len[2];
+ u8 id_data[ID_LEN];
+ u8 vpdr_tag;
+ u8 vpdr_len[2];
+ VPD_ENTRY(pn, 16); /* part number */
+ VPD_ENTRY(ec, EC_LEN); /* EC level */
+ VPD_ENTRY(sn, SERNUM_LEN); /* serial number */
+ VPD_ENTRY(na, 12); /* MAC address base */
+ VPD_ENTRY(port_type, 8); /* port types */
+ VPD_ENTRY(gpio, 14); /* GPIO usage */
+ VPD_ENTRY(cclk, 6); /* core clock */
+ VPD_ENTRY(port_addr, 8); /* port MDIO addresses */
+ VPD_ENTRY(rv, 1); /* csum */
+ u32 pad; /* for multiple-of-4 sizing and alignment */
+};
+
+#define EEPROM_STAT_ADDR 0x7bfc
+#define VPD_BASE 0
+
+/**
+ * t4_seeprom_wp - enable/disable EEPROM write protection
+ * @adapter: the adapter
+ * @enable: whether to enable or disable write protection
+ *
+ * Enables or disables write protection on the serial EEPROM.
+ */
+int t4_seeprom_wp(struct adapter *adapter, bool enable)
+{
+ unsigned int v = enable ? 0xc : 0;
+ int ret = pci_write_vpd(adapter->pdev, EEPROM_STAT_ADDR, 4, &v);
+ return ret < 0 ? ret : 0;
+}
+
+/**
+ * get_vpd_params - read VPD parameters from VPD EEPROM
+ * @adapter: adapter to read
+ * @p: where to store the parameters
+ *
+ * Reads card parameters stored in VPD EEPROM.
+ */
+static int get_vpd_params(struct adapter *adapter, struct vpd_params *p)
+{
+ int ret;
+ struct t4_vpd vpd;
+ u8 *q = (u8 *)&vpd, csum;
+
+ ret = pci_read_vpd(adapter->pdev, VPD_BASE, sizeof(vpd), &vpd);
+ if (ret < 0)
+ return ret;
+
+ for (csum = 0; q <= vpd.rv_data; q++)
+ csum += *q;
+
+ if (csum) {
+ dev_err(adapter->pdev_dev,
+ "corrupted VPD EEPROM, actual csum %u\n", csum);
+ return -EINVAL;
+ }
+
+ p->cclk = simple_strtoul(vpd.cclk_data, NULL, 10);
+ memcpy(p->id, vpd.id_data, sizeof(vpd.id_data));
+ strim(p->id);
+ memcpy(p->ec, vpd.ec_data, sizeof(vpd.ec_data));
+ strim(p->ec);
+ memcpy(p->sn, vpd.sn_data, sizeof(vpd.sn_data));
+ strim(p->sn);
+ return 0;
+}
+
+/* serial flash and firmware constants */
+enum {
+ SF_ATTEMPTS = 10, /* max retries for SF operations */
+
+ /* flash command opcodes */
+ SF_PROG_PAGE = 2, /* program page */
+ SF_WR_DISABLE = 4, /* disable writes */
+ SF_RD_STATUS = 5, /* read status register */
+ SF_WR_ENABLE = 6, /* enable writes */
+ SF_RD_DATA_FAST = 0xb, /* read flash */
+ SF_ERASE_SECTOR = 0xd8, /* erase sector */
+
+ FW_START_SEC = 8, /* first flash sector for FW */
+ FW_END_SEC = 15, /* last flash sector for FW */
+ FW_IMG_START = FW_START_SEC * SF_SEC_SIZE,
+ FW_MAX_SIZE = (FW_END_SEC - FW_START_SEC + 1) * SF_SEC_SIZE,
+};
+
+/**
+ * sf1_read - read data from the serial flash
+ * @adapter: the adapter
+ * @byte_cnt: number of bytes to read
+ * @cont: whether another operation will be chained
+ * @lock: whether to lock SF for PL access only
+ * @valp: where to store the read data
+ *
+ * Reads up to 4 bytes of data from the serial flash. The location of
+ * the read needs to be specified prior to calling this by issuing the
+ * appropriate commands to the serial flash.
+ */
+static int sf1_read(struct adapter *adapter, unsigned int byte_cnt, int cont,
+ int lock, u32 *valp)
+{
+ int ret;
+
+ if (!byte_cnt || byte_cnt > 4)
+ return -EINVAL;
+ if (t4_read_reg(adapter, SF_OP) & BUSY)
+ return -EBUSY;
+ cont = cont ? SF_CONT : 0;
+ lock = lock ? SF_LOCK : 0;
+ t4_write_reg(adapter, SF_OP, lock | cont | BYTECNT(byte_cnt - 1));
+ ret = t4_wait_op_done(adapter, SF_OP, BUSY, 0, SF_ATTEMPTS, 5);
+ if (!ret)
+ *valp = t4_read_reg(adapter, SF_DATA);
+ return ret;
+}
+
+/**
+ * sf1_write - write data to the serial flash
+ * @adapter: the adapter
+ * @byte_cnt: number of bytes to write
+ * @cont: whether another operation will be chained
+ * @lock: whether to lock SF for PL access only
+ * @val: value to write
+ *
+ * Writes up to 4 bytes of data to the serial flash. The location of
+ * the write needs to be specified prior to calling this by issuing the
+ * appropriate commands to the serial flash.
+ */
+static int sf1_write(struct adapter *adapter, unsigned int byte_cnt, int cont,
+ int lock, u32 val)
+{
+ if (!byte_cnt || byte_cnt > 4)
+ return -EINVAL;
+ if (t4_read_reg(adapter, SF_OP) & BUSY)
+ return -EBUSY;
+ cont = cont ? SF_CONT : 0;
+ lock = lock ? SF_LOCK : 0;
+ t4_write_reg(adapter, SF_DATA, val);
+ t4_write_reg(adapter, SF_OP, lock |
+ cont | BYTECNT(byte_cnt - 1) | OP_WR);
+ return t4_wait_op_done(adapter, SF_OP, BUSY, 0, SF_ATTEMPTS, 5);
+}
+
+/**
+ * flash_wait_op - wait for a flash operation to complete
+ * @adapter: the adapter
+ * @attempts: max number of polls of the status register
+ * @delay: delay between polls in ms
+ *
+ * Wait for a flash operation to complete by polling the status register.
+ */
+static int flash_wait_op(struct adapter *adapter, int attempts, int delay)
+{
+ int ret;
+ u32 status;
+
+ while (1) {
+ if ((ret = sf1_write(adapter, 1, 1, 1, SF_RD_STATUS)) != 0 ||
+ (ret = sf1_read(adapter, 1, 0, 1, &status)) != 0)
+ return ret;
+ if (!(status & 1))
+ return 0;
+ if (--attempts == 0)
+ return -EAGAIN;
+ if (delay)
+ msleep(delay);
+ }
+}
+
+/**
+ * t4_read_flash - read words from serial flash
+ * @adapter: the adapter
+ * @addr: the start address for the read
+ * @nwords: how many 32-bit words to read
+ * @data: where to store the read data
+ * @byte_oriented: whether to store data as bytes or as words
+ *
+ * Read the specified number of 32-bit words from the serial flash.
+ * If @byte_oriented is set the read data is stored as a byte array
+ * (i.e., big-endian), otherwise as 32-bit words in the platform's
+ * natural endianess.
+ */
+int t4_read_flash(struct adapter *adapter, unsigned int addr,
+ unsigned int nwords, u32 *data, int byte_oriented)
+{
+ int ret;
+
+ if (addr + nwords * sizeof(u32) > SF_SIZE || (addr & 3))
+ return -EINVAL;
+
+ addr = swab32(addr) | SF_RD_DATA_FAST;
+
+ if ((ret = sf1_write(adapter, 4, 1, 0, addr)) != 0 ||
+ (ret = sf1_read(adapter, 1, 1, 0, data)) != 0)
+ return ret;
+
+ for ( ; nwords; nwords--, data++) {
+ ret = sf1_read(adapter, 4, nwords > 1, nwords == 1, data);
+ if (nwords == 1)
+ t4_write_reg(adapter, SF_OP, 0); /* unlock SF */
+ if (ret)
+ return ret;
+ if (byte_oriented)
+ *data = htonl(*data);
+ }
+ return 0;
+}
+
+/**
+ * t4_write_flash - write up to a page of data to the serial flash
+ * @adapter: the adapter
+ * @addr: the start address to write
+ * @n: length of data to write in bytes
+ * @data: the data to write
+ *
+ * Writes up to a page of data (256 bytes) to the serial flash starting
+ * at the given address. All the data must be written to the same page.
+ */
+static int t4_write_flash(struct adapter *adapter, unsigned int addr,
+ unsigned int n, const u8 *data)
+{
+ int ret;
+ u32 buf[64];
+ unsigned int i, c, left, val, offset = addr & 0xff;
+
+ if (addr >= SF_SIZE || offset + n > SF_PAGE_SIZE)
+ return -EINVAL;
+
+ val = swab32(addr) | SF_PROG_PAGE;
+
+ if ((ret = sf1_write(adapter, 1, 0, 1, SF_WR_ENABLE)) != 0 ||
+ (ret = sf1_write(adapter, 4, 1, 1, val)) != 0)
+ goto unlock;
+
+ for (left = n; left; left -= c) {
+ c = min(left, 4U);
+ for (val = 0, i = 0; i < c; ++i)
+ val = (val << 8) + *data++;
+
+ ret = sf1_write(adapter, c, c != left, 1, val);
+ if (ret)
+ goto unlock;
+ }
+ ret = flash_wait_op(adapter, 5, 1);
+ if (ret)
+ goto unlock;
+
+ t4_write_reg(adapter, SF_OP, 0); /* unlock SF */
+
+ /* Read the page to verify the write succeeded */
+ ret = t4_read_flash(adapter, addr & ~0xff, ARRAY_SIZE(buf), buf, 1);
+ if (ret)
+ return ret;
+
+ if (memcmp(data - n, (u8 *)buf + offset, n)) {
+ dev_err(adapter->pdev_dev,
+ "failed to correctly write the flash page at %#x\n",
+ addr);
+ return -EIO;
+ }
+ return 0;
+
+unlock:
+ t4_write_reg(adapter, SF_OP, 0); /* unlock SF */
+ return ret;
+}
+
+/**
+ * get_fw_version - read the firmware version
+ * @adapter: the adapter
+ * @vers: where to place the version
+ *
+ * Reads the FW version from flash.
+ */
+static int get_fw_version(struct adapter *adapter, u32 *vers)
+{
+ return t4_read_flash(adapter,
+ FW_IMG_START + offsetof(struct fw_hdr, fw_ver), 1,
+ vers, 0);
+}
+
+/**
+ * get_tp_version - read the TP microcode version
+ * @adapter: the adapter
+ * @vers: where to place the version
+ *
+ * Reads the TP microcode version from flash.
+ */
+static int get_tp_version(struct adapter *adapter, u32 *vers)
+{
+ return t4_read_flash(adapter, FW_IMG_START + offsetof(struct fw_hdr,
+ tp_microcode_ver),
+ 1, vers, 0);
+}
+
+/**
+ * t4_check_fw_version - check if the FW is compatible with this driver
+ * @adapter: the adapter
+ *
+ * Checks if an adapter's FW is compatible with the driver. Returns 0
+ * if there's exact match, a negative error if the version could not be
+ * read or there's a major version mismatch, and a positive value if the
+ * expected major version is found but there's a minor version mismatch.
+ */
+int t4_check_fw_version(struct adapter *adapter)
+{
+ int ret, major, minor, micro;
+
+ ret = get_fw_version(adapter, &adapter->params.fw_vers);
+ if (!ret)
+ ret = get_tp_version(adapter, &adapter->params.tp_vers);
+ if (ret)
+ return ret;
+
+ major = FW_HDR_FW_VER_MAJOR_GET(adapter->params.fw_vers);
+ minor = FW_HDR_FW_VER_MINOR_GET(adapter->params.fw_vers);
+ micro = FW_HDR_FW_VER_MICRO_GET(adapter->params.fw_vers);
+
+ if (major != FW_VERSION_MAJOR) { /* major mismatch - fail */
+ dev_err(adapter->pdev_dev,
+ "card FW has major version %u, driver wants %u\n",
+ major, FW_VERSION_MAJOR);
+ return -EINVAL;
+ }
+
+ if (minor == FW_VERSION_MINOR && micro == FW_VERSION_MICRO)
+ return 0; /* perfect match */
+
+ /* Minor/micro version mismatch. Report it but often it's OK. */
+ return 1;
+}
+
+/**
+ * t4_flash_erase_sectors - erase a range of flash sectors
+ * @adapter: the adapter
+ * @start: the first sector to erase
+ * @end: the last sector to erase
+ *
+ * Erases the sectors in the given inclusive range.
+ */
+static int t4_flash_erase_sectors(struct adapter *adapter, int start, int end)
+{
+ int ret = 0;
+
+ while (start <= end) {
+ if ((ret = sf1_write(adapter, 1, 0, 1, SF_WR_ENABLE)) != 0 ||
+ (ret = sf1_write(adapter, 4, 0, 1,
+ SF_ERASE_SECTOR | (start << 8))) != 0 ||
+ (ret = flash_wait_op(adapter, 5, 500)) != 0) {
+ dev_err(adapter->pdev_dev,
+ "erase of flash sector %d failed, error %d\n",
+ start, ret);
+ break;
+ }
+ start++;
+ }
+ t4_write_reg(adapter, SF_OP, 0); /* unlock SF */
+ return ret;
+}
+
+/**
+ * t4_load_fw - download firmware
+ * @adap: the adapter
+ * @fw_data: the firmware image to write
+ * @size: image size
+ *
+ * Write the supplied firmware image to the card's serial flash.
+ */
+int t4_load_fw(struct adapter *adap, const u8 *fw_data, unsigned int size)
+{
+ u32 csum;
+ __be32 vers;
+ int ret, addr;
+ unsigned int i;
+ u8 first_page[SF_PAGE_SIZE];
+ const u32 *p = (const u32 *)fw_data;
+ struct fw_hdr *hdr = (struct fw_hdr *)fw_data;
+
+ if (!size) {
+ dev_err(adap->pdev_dev, "FW image has no data\n");
+ return -EINVAL;
+ }
+ if (size & 511) {
+ dev_err(adap->pdev_dev,
+ "FW image size not multiple of 512 bytes\n");
+ return -EINVAL;
+ }
+ if (ntohs(hdr->len512) * 512 != size) {
+ dev_err(adap->pdev_dev,
+ "FW image size differs from size in FW header\n");
+ return -EINVAL;
+ }
+ if (size > FW_MAX_SIZE) {
+ dev_err(adap->pdev_dev, "FW image too large, max is %u bytes\n",
+ FW_MAX_SIZE);
+ return -EFBIG;
+ }
+
+ for (csum = 0, i = 0; i < size / sizeof(csum); i++)
+ csum += ntohl(p[i]);
+
+ if (csum != 0xffffffff) {
+ dev_err(adap->pdev_dev,
+ "corrupted firmware image, checksum %#x\n", csum);
+ return -EINVAL;
+ }
+
+ i = DIV_ROUND_UP(size, SF_SEC_SIZE); /* # of sectors spanned */
+ ret = t4_flash_erase_sectors(adap, FW_START_SEC, FW_START_SEC + i - 1);
+ if (ret)
+ goto out;
+
+ /*
+ * We write the correct version at the end so the driver can see a bad
+ * version if the FW write fails. Start by writing a copy of the
+ * first page with a bad version.
+ */
+ vers = hdr->fw_ver;
+ memcpy(first_page, fw_data, SF_PAGE_SIZE);
+ ((struct fw_hdr *)first_page)->fw_ver = htonl(0xffffffff);
+ ret = t4_write_flash(adap, FW_IMG_START, SF_PAGE_SIZE, first_page);
+ if (ret)
+ goto out;
+
+ addr = FW_IMG_START;
+ for (size -= SF_PAGE_SIZE ; size; size -= SF_PAGE_SIZE) {
+ addr += SF_PAGE_SIZE;
+ fw_data += SF_PAGE_SIZE;
+ ret = t4_write_flash(adap, addr, SF_PAGE_SIZE, fw_data);
+ if (ret)
+ goto out;
+ }
+
+ ret = t4_write_flash(adap,
+ FW_IMG_START + offsetof(struct fw_hdr, fw_ver),
+ sizeof(vers), (const u8 *)&vers);
+out:
+ if (ret)
+ dev_err(adap->pdev_dev, "firmware download failed, error %d\n",
+ ret);
+ return ret;
+}
+
+#define ADVERT_MASK (FW_PORT_CAP_SPEED_100M | FW_PORT_CAP_SPEED_1G |\
+ FW_PORT_CAP_SPEED_10G | FW_PORT_CAP_ANEG)
+
+/**
+ * t4_link_start - apply link configuration to MAC/PHY
+ * @phy: the PHY to setup
+ * @mac: the MAC to setup
+ * @lc: the requested link configuration
+ *
+ * Set up a port's MAC and PHY according to a desired link configuration.
+ * - If the PHY can auto-negotiate first decide what to advertise, then
+ * enable/disable auto-negotiation as desired, and reset.
+ * - If the PHY does not auto-negotiate just reset it.
+ * - If auto-negotiation is off set the MAC to the proper speed/duplex/FC,
+ * otherwise do it later based on the outcome of auto-negotiation.
+ */
+int t4_link_start(struct adapter *adap, unsigned int mbox, unsigned int port,
+ struct link_config *lc)
+{
+ struct fw_port_cmd c;
+ unsigned int fc = 0, mdi = FW_PORT_MDI(FW_PORT_MDI_AUTO);
+
+ lc->link_ok = 0;
+ if (lc->requested_fc & PAUSE_RX)
+ fc |= FW_PORT_CAP_FC_RX;
+ if (lc->requested_fc & PAUSE_TX)
+ fc |= FW_PORT_CAP_FC_TX;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_portid = htonl(FW_CMD_OP(FW_PORT_CMD) | FW_CMD_REQUEST |
+ FW_CMD_EXEC | FW_PORT_CMD_PORTID(port));
+ c.action_to_len16 = htonl(FW_PORT_CMD_ACTION(FW_PORT_ACTION_L1_CFG) |
+ FW_LEN16(c));
+
+ if (!(lc->supported & FW_PORT_CAP_ANEG)) {
+ c.u.l1cfg.rcap = htonl((lc->supported & ADVERT_MASK) | fc);
+ lc->fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX);
+ } else if (lc->autoneg == AUTONEG_DISABLE) {
+ c.u.l1cfg.rcap = htonl(lc->requested_speed | fc | mdi);
+ lc->fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX);
+ } else
+ c.u.l1cfg.rcap = htonl(lc->advertising | fc | mdi);
+
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_restart_aneg - restart autonegotiation
+ * @adap: the adapter
+ * @mbox: mbox to use for the FW command
+ * @port: the port id
+ *
+ * Restarts autonegotiation for the selected port.
+ */
+int t4_restart_aneg(struct adapter *adap, unsigned int mbox, unsigned int port)
+{
+ struct fw_port_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_portid = htonl(FW_CMD_OP(FW_PORT_CMD) | FW_CMD_REQUEST |
+ FW_CMD_EXEC | FW_PORT_CMD_PORTID(port));
+ c.action_to_len16 = htonl(FW_PORT_CMD_ACTION(FW_PORT_ACTION_L1_CFG) |
+ FW_LEN16(c));
+ c.u.l1cfg.rcap = htonl(FW_PORT_CAP_ANEG);
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_set_vlan_accel - configure HW VLAN extraction
+ * @adap: the adapter
+ * @ports: bitmap of adapter ports to operate on
+ * @on: enable (1) or disable (0) HW VLAN extraction
+ *
+ * Enables or disables HW extraction of VLAN tags for the ports specified
+ * by @ports. @ports is a bitmap with the ith bit designating the port
+ * associated with the ith adapter channel.
+ */
+void t4_set_vlan_accel(struct adapter *adap, unsigned int ports, int on)
+{
+ ports <<= VLANEXTENABLE_SHIFT;
+ t4_set_reg_field(adap, TP_OUT_CONFIG, ports, on ? ports : 0);
+}
+
+struct intr_info {
+ unsigned int mask; /* bits to check in interrupt status */
+ const char *msg; /* message to print or NULL */
+ short stat_idx; /* stat counter to increment or -1 */
+ unsigned short fatal; /* whether the condition reported is fatal */
+};
+
+/**
+ * t4_handle_intr_status - table driven interrupt handler
+ * @adapter: the adapter that generated the interrupt
+ * @reg: the interrupt status register to process
+ * @acts: table of interrupt actions
+ *
+ * A table driven interrupt handler that applies a set of masks to an
+ * interrupt status word and performs the corresponding actions if the
+ * interrupts described by the mask have occured. The actions include
+ * optionally emitting a warning or alert message. The table is terminated
+ * by an entry specifying mask 0. Returns the number of fatal interrupt
+ * conditions.
+ */
+static int t4_handle_intr_status(struct adapter *adapter, unsigned int reg,
+ const struct intr_info *acts)
+{
+ int fatal = 0;
+ unsigned int mask = 0;
+ unsigned int status = t4_read_reg(adapter, reg);
+
+ for ( ; acts->mask; ++acts) {
+ if (!(status & acts->mask))
+ continue;
+ if (acts->fatal) {
+ fatal++;
+ dev_alert(adapter->pdev_dev, "%s (0x%x)\n", acts->msg,
+ status & acts->mask);
+ } else if (acts->msg && printk_ratelimit())
+ dev_warn(adapter->pdev_dev, "%s (0x%x)\n", acts->msg,
+ status & acts->mask);
+ mask |= acts->mask;
+ }
+ status &= mask;
+ if (status) /* clear processed interrupts */
+ t4_write_reg(adapter, reg, status);
+ return fatal;
+}
+
+/*
+ * Interrupt handler for the PCIE module.
+ */
+static void pcie_intr_handler(struct adapter *adapter)
+{
+ static struct intr_info sysbus_intr_info[] = {
+ { RNPP, "RXNP array parity error", -1, 1 },
+ { RPCP, "RXPC array parity error", -1, 1 },
+ { RCIP, "RXCIF array parity error", -1, 1 },
+ { RCCP, "Rx completions control array parity error", -1, 1 },
+ { RFTP, "RXFT array parity error", -1, 1 },
+ { 0 }
+ };
+ static struct intr_info pcie_port_intr_info[] = {
+ { TPCP, "TXPC array parity error", -1, 1 },
+ { TNPP, "TXNP array parity error", -1, 1 },
+ { TFTP, "TXFT array parity error", -1, 1 },
+ { TCAP, "TXCA array parity error", -1, 1 },
+ { TCIP, "TXCIF array parity error", -1, 1 },
+ { RCAP, "RXCA array parity error", -1, 1 },
+ { OTDD, "outbound request TLP discarded", -1, 1 },
+ { RDPE, "Rx data parity error", -1, 1 },
+ { TDUE, "Tx uncorrectable data error", -1, 1 },
+ { 0 }
+ };
+ static struct intr_info pcie_intr_info[] = {
+ { MSIADDRLPERR, "MSI AddrL parity error", -1, 1 },
+ { MSIADDRHPERR, "MSI AddrH parity error", -1, 1 },
+ { MSIDATAPERR, "MSI data parity error", -1, 1 },
+ { MSIXADDRLPERR, "MSI-X AddrL parity error", -1, 1 },
+ { MSIXADDRHPERR, "MSI-X AddrH parity error", -1, 1 },
+ { MSIXDATAPERR, "MSI-X data parity error", -1, 1 },
+ { MSIXDIPERR, "MSI-X DI parity error", -1, 1 },
+ { PIOCPLPERR, "PCI PIO completion FIFO parity error", -1, 1 },
+ { PIOREQPERR, "PCI PIO request FIFO parity error", -1, 1 },
+ { TARTAGPERR, "PCI PCI target tag FIFO parity error", -1, 1 },
+ { CCNTPERR, "PCI CMD channel count parity error", -1, 1 },
+ { CREQPERR, "PCI CMD channel request parity error", -1, 1 },
+ { CRSPPERR, "PCI CMD channel response parity error", -1, 1 },
+ { DCNTPERR, "PCI DMA channel count parity error", -1, 1 },
+ { DREQPERR, "PCI DMA channel request parity error", -1, 1 },
+ { DRSPPERR, "PCI DMA channel response parity error", -1, 1 },
+ { HCNTPERR, "PCI HMA channel count parity error", -1, 1 },
+ { HREQPERR, "PCI HMA channel request parity error", -1, 1 },
+ { HRSPPERR, "PCI HMA channel response parity error", -1, 1 },
+ { CFGSNPPERR, "PCI config snoop FIFO parity error", -1, 1 },
+ { FIDPERR, "PCI FID parity error", -1, 1 },
+ { INTXCLRPERR, "PCI INTx clear parity error", -1, 1 },
+ { MATAGPERR, "PCI MA tag parity error", -1, 1 },
+ { PIOTAGPERR, "PCI PIO tag parity error", -1, 1 },
+ { RXCPLPERR, "PCI Rx completion parity error", -1, 1 },
+ { RXWRPERR, "PCI Rx write parity error", -1, 1 },
+ { RPLPERR, "PCI replay buffer parity error", -1, 1 },
+ { PCIESINT, "PCI core secondary fault", -1, 1 },
+ { PCIEPINT, "PCI core primary fault", -1, 1 },
+ { UNXSPLCPLERR, "PCI unexpected split completion error", -1, 0 },
+ { 0 }
+ };
+
+ int fat;
+
+ fat = t4_handle_intr_status(adapter,
+ PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS,
+ sysbus_intr_info) +
+ t4_handle_intr_status(adapter,
+ PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS,
+ pcie_port_intr_info) +
+ t4_handle_intr_status(adapter, PCIE_INT_CAUSE, pcie_intr_info);
+ if (fat)
+ t4_fatal_err(adapter);
+}
+
+/*
+ * TP interrupt handler.
+ */
+static void tp_intr_handler(struct adapter *adapter)
+{
+ static struct intr_info tp_intr_info[] = {
+ { 0x3fffffff, "TP parity error", -1, 1 },
+ { FLMTXFLSTEMPTY, "TP out of Tx pages", -1, 1 },
+ { 0 }
+ };
+
+ if (t4_handle_intr_status(adapter, TP_INT_CAUSE, tp_intr_info))
+ t4_fatal_err(adapter);
+}
+
+/*
+ * SGE interrupt handler.
+ */
+static void sge_intr_handler(struct adapter *adapter)
+{
+ u64 v;
+
+ static struct intr_info sge_intr_info[] = {
+ { ERR_CPL_EXCEED_IQE_SIZE,
+ "SGE received CPL exceeding IQE size", -1, 1 },
+ { ERR_INVALID_CIDX_INC,
+ "SGE GTS CIDX increment too large", -1, 0 },
+ { ERR_CPL_OPCODE_0, "SGE received 0-length CPL", -1, 0 },
+ { ERR_DROPPED_DB, "SGE doorbell dropped", -1, 0 },
+ { ERR_DATA_CPL_ON_HIGH_QID1 | ERR_DATA_CPL_ON_HIGH_QID0,
+ "SGE IQID > 1023 received CPL for FL", -1, 0 },
+ { ERR_BAD_DB_PIDX3, "SGE DBP 3 pidx increment too large", -1,
+ 0 },
+ { ERR_BAD_DB_PIDX2, "SGE DBP 2 pidx increment too large", -1,
+ 0 },
+ { ERR_BAD_DB_PIDX1, "SGE DBP 1 pidx increment too large", -1,
+ 0 },
+ { ERR_BAD_DB_PIDX0, "SGE DBP 0 pidx increment too large", -1,
+ 0 },
+ { ERR_ING_CTXT_PRIO,
+ "SGE too many priority ingress contexts", -1, 0 },
+ { ERR_EGR_CTXT_PRIO,
+ "SGE too many priority egress contexts", -1, 0 },
+ { INGRESS_SIZE_ERR, "SGE illegal ingress QID", -1, 0 },
+ { EGRESS_SIZE_ERR, "SGE illegal egress QID", -1, 0 },
+ { 0 }
+ };
+
+ v = (u64)t4_read_reg(adapter, SGE_INT_CAUSE1) |
+ ((u64)t4_read_reg(adapter, SGE_INT_CAUSE2) << 32);
+ if (v) {
+ dev_alert(adapter->pdev_dev, "SGE parity error (%#llx)\n",
+ (unsigned long long)v);
+ t4_write_reg(adapter, SGE_INT_CAUSE1, v);
+ t4_write_reg(adapter, SGE_INT_CAUSE2, v >> 32);
+ }
+
+ if (t4_handle_intr_status(adapter, SGE_INT_CAUSE3, sge_intr_info) ||
+ v != 0)
+ t4_fatal_err(adapter);
+}
+
+/*
+ * CIM interrupt handler.
+ */
+static void cim_intr_handler(struct adapter *adapter)
+{
+ static struct intr_info cim_intr_info[] = {
+ { PREFDROPINT, "CIM control register prefetch drop", -1, 1 },
+ { OBQPARERR, "CIM OBQ parity error", -1, 1 },
+ { IBQPARERR, "CIM IBQ parity error", -1, 1 },
+ { MBUPPARERR, "CIM mailbox uP parity error", -1, 1 },
+ { MBHOSTPARERR, "CIM mailbox host parity error", -1, 1 },
+ { TIEQINPARERRINT, "CIM TIEQ outgoing parity error", -1, 1 },
+ { TIEQOUTPARERRINT, "CIM TIEQ incoming parity error", -1, 1 },
+ { 0 }
+ };
+ static struct intr_info cim_upintr_info[] = {
+ { RSVDSPACEINT, "CIM reserved space access", -1, 1 },
+ { ILLTRANSINT, "CIM illegal transaction", -1, 1 },
+ { ILLWRINT, "CIM illegal write", -1, 1 },
+ { ILLRDINT, "CIM illegal read", -1, 1 },
+ { ILLRDBEINT, "CIM illegal read BE", -1, 1 },
+ { ILLWRBEINT, "CIM illegal write BE", -1, 1 },
+ { SGLRDBOOTINT, "CIM single read from boot space", -1, 1 },
+ { SGLWRBOOTINT, "CIM single write to boot space", -1, 1 },
+ { BLKWRBOOTINT, "CIM block write to boot space", -1, 1 },
+ { SGLRDFLASHINT, "CIM single read from flash space", -1, 1 },
+ { SGLWRFLASHINT, "CIM single write to flash space", -1, 1 },
+ { BLKWRFLASHINT, "CIM block write to flash space", -1, 1 },
+ { SGLRDEEPROMINT, "CIM single EEPROM read", -1, 1 },
+ { SGLWREEPROMINT, "CIM single EEPROM write", -1, 1 },
+ { BLKRDEEPROMINT, "CIM block EEPROM read", -1, 1 },
+ { BLKWREEPROMINT, "CIM block EEPROM write", -1, 1 },
+ { SGLRDCTLINT , "CIM single read from CTL space", -1, 1 },
+ { SGLWRCTLINT , "CIM single write to CTL space", -1, 1 },
+ { BLKRDCTLINT , "CIM block read from CTL space", -1, 1 },
+ { BLKWRCTLINT , "CIM block write to CTL space", -1, 1 },
+ { SGLRDPLINT , "CIM single read from PL space", -1, 1 },
+ { SGLWRPLINT , "CIM single write to PL space", -1, 1 },
+ { BLKRDPLINT , "CIM block read from PL space", -1, 1 },
+ { BLKWRPLINT , "CIM block write to PL space", -1, 1 },
+ { REQOVRLOOKUPINT , "CIM request FIFO overwrite", -1, 1 },
+ { RSPOVRLOOKUPINT , "CIM response FIFO overwrite", -1, 1 },
+ { TIMEOUTINT , "CIM PIF timeout", -1, 1 },
+ { TIMEOUTMAINT , "CIM PIF MA timeout", -1, 1 },
+ { 0 }
+ };
+
+ int fat;
+
+ fat = t4_handle_intr_status(adapter, CIM_HOST_INT_CAUSE,
+ cim_intr_info) +
+ t4_handle_intr_status(adapter, CIM_HOST_UPACC_INT_CAUSE,
+ cim_upintr_info);
+ if (fat)
+ t4_fatal_err(adapter);
+}
+
+/*
+ * ULP RX interrupt handler.
+ */
+static void ulprx_intr_handler(struct adapter *adapter)
+{
+ static struct intr_info ulprx_intr_info[] = {
+ { 0x7fffff, "ULPRX parity error", -1, 1 },
+ { 0 }
+ };
+
+ if (t4_handle_intr_status(adapter, ULP_RX_INT_CAUSE, ulprx_intr_info))
+ t4_fatal_err(adapter);
+}
+
+/*
+ * ULP TX interrupt handler.
+ */
+static void ulptx_intr_handler(struct adapter *adapter)
+{
+ static struct intr_info ulptx_intr_info[] = {
+ { PBL_BOUND_ERR_CH3, "ULPTX channel 3 PBL out of bounds", -1,
+ 0 },
+ { PBL_BOUND_ERR_CH2, "ULPTX channel 2 PBL out of bounds", -1,
+ 0 },
+ { PBL_BOUND_ERR_CH1, "ULPTX channel 1 PBL out of bounds", -1,
+ 0 },
+ { PBL_BOUND_ERR_CH0, "ULPTX channel 0 PBL out of bounds", -1,
+ 0 },
+ { 0xfffffff, "ULPTX parity error", -1, 1 },
+ { 0 }
+ };
+
+ if (t4_handle_intr_status(adapter, ULP_TX_INT_CAUSE, ulptx_intr_info))
+ t4_fatal_err(adapter);
+}
+
+/*
+ * PM TX interrupt handler.
+ */
+static void pmtx_intr_handler(struct adapter *adapter)
+{
+ static struct intr_info pmtx_intr_info[] = {
+ { PCMD_LEN_OVFL0, "PMTX channel 0 pcmd too large", -1, 1 },
+ { PCMD_LEN_OVFL1, "PMTX channel 1 pcmd too large", -1, 1 },
+ { PCMD_LEN_OVFL2, "PMTX channel 2 pcmd too large", -1, 1 },
+ { ZERO_C_CMD_ERROR, "PMTX 0-length pcmd", -1, 1 },
+ { PMTX_FRAMING_ERROR, "PMTX framing error", -1, 1 },
+ { OESPI_PAR_ERROR, "PMTX oespi parity error", -1, 1 },
+ { DB_OPTIONS_PAR_ERROR, "PMTX db_options parity error", -1, 1 },
+ { ICSPI_PAR_ERROR, "PMTX icspi parity error", -1, 1 },
+ { C_PCMD_PAR_ERROR, "PMTX c_pcmd parity error", -1, 1},
+ { 0 }
+ };
+
+ if (t4_handle_intr_status(adapter, PM_TX_INT_CAUSE, pmtx_intr_info))
+ t4_fatal_err(adapter);
+}
+
+/*
+ * PM RX interrupt handler.
+ */
+static void pmrx_intr_handler(struct adapter *adapter)
+{
+ static struct intr_info pmrx_intr_info[] = {
+ { ZERO_E_CMD_ERROR, "PMRX 0-length pcmd", -1, 1 },
+ { PMRX_FRAMING_ERROR, "PMRX framing error", -1, 1 },
+ { OCSPI_PAR_ERROR, "PMRX ocspi parity error", -1, 1 },
+ { DB_OPTIONS_PAR_ERROR, "PMRX db_options parity error", -1, 1 },
+ { IESPI_PAR_ERROR, "PMRX iespi parity error", -1, 1 },
+ { E_PCMD_PAR_ERROR, "PMRX e_pcmd parity error", -1, 1},
+ { 0 }
+ };
+
+ if (t4_handle_intr_status(adapter, PM_RX_INT_CAUSE, pmrx_intr_info))
+ t4_fatal_err(adapter);
+}
+
+/*
+ * CPL switch interrupt handler.
+ */
+static void cplsw_intr_handler(struct adapter *adapter)
+{
+ static struct intr_info cplsw_intr_info[] = {
+ { CIM_OP_MAP_PERR, "CPLSW CIM op_map parity error", -1, 1 },
+ { CIM_OVFL_ERROR, "CPLSW CIM overflow", -1, 1 },
+ { TP_FRAMING_ERROR, "CPLSW TP framing error", -1, 1 },
+ { SGE_FRAMING_ERROR, "CPLSW SGE framing error", -1, 1 },
+ { CIM_FRAMING_ERROR, "CPLSW CIM framing error", -1, 1 },
+ { ZERO_SWITCH_ERROR, "CPLSW no-switch error", -1, 1 },
+ { 0 }
+ };
+
+ if (t4_handle_intr_status(adapter, CPL_INTR_CAUSE, cplsw_intr_info))
+ t4_fatal_err(adapter);
+}
+
+/*
+ * LE interrupt handler.
+ */
+static void le_intr_handler(struct adapter *adap)
+{
+ static struct intr_info le_intr_info[] = {
+ { LIPMISS, "LE LIP miss", -1, 0 },
+ { LIP0, "LE 0 LIP error", -1, 0 },
+ { PARITYERR, "LE parity error", -1, 1 },
+ { UNKNOWNCMD, "LE unknown command", -1, 1 },
+ { REQQPARERR, "LE request queue parity error", -1, 1 },
+ { 0 }
+ };
+
+ if (t4_handle_intr_status(adap, LE_DB_INT_CAUSE, le_intr_info))
+ t4_fatal_err(adap);
+}
+
+/*
+ * MPS interrupt handler.
+ */
+static void mps_intr_handler(struct adapter *adapter)
+{
+ static struct intr_info mps_rx_intr_info[] = {
+ { 0xffffff, "MPS Rx parity error", -1, 1 },
+ { 0 }
+ };
+ static struct intr_info mps_tx_intr_info[] = {
+ { TPFIFO, "MPS Tx TP FIFO parity error", -1, 1 },
+ { NCSIFIFO, "MPS Tx NC-SI FIFO parity error", -1, 1 },
+ { TXDATAFIFO, "MPS Tx data FIFO parity error", -1, 1 },
+ { TXDESCFIFO, "MPS Tx desc FIFO parity error", -1, 1 },
+ { BUBBLE, "MPS Tx underflow", -1, 1 },
+ { SECNTERR, "MPS Tx SOP/EOP error", -1, 1 },
+ { FRMERR, "MPS Tx framing error", -1, 1 },
+ { 0 }
+ };
+ static struct intr_info mps_trc_intr_info[] = {
+ { FILTMEM, "MPS TRC filter parity error", -1, 1 },
+ { PKTFIFO, "MPS TRC packet FIFO parity error", -1, 1 },
+ { MISCPERR, "MPS TRC misc parity error", -1, 1 },
+ { 0 }
+ };
+ static struct intr_info mps_stat_sram_intr_info[] = {
+ { 0x1fffff, "MPS statistics SRAM parity error", -1, 1 },
+ { 0 }
+ };
+ static struct intr_info mps_stat_tx_intr_info[] = {
+ { 0xfffff, "MPS statistics Tx FIFO parity error", -1, 1 },
+ { 0 }
+ };
+ static struct intr_info mps_stat_rx_intr_info[] = {
+ { 0xffffff, "MPS statistics Rx FIFO parity error", -1, 1 },
+ { 0 }
+ };
+ static struct intr_info mps_cls_intr_info[] = {
+ { MATCHSRAM, "MPS match SRAM parity error", -1, 1 },
+ { MATCHTCAM, "MPS match TCAM parity error", -1, 1 },
+ { HASHSRAM, "MPS hash SRAM parity error", -1, 1 },
+ { 0 }
+ };
+
+ int fat;
+
+ fat = t4_handle_intr_status(adapter, MPS_RX_PERR_INT_CAUSE,
+ mps_rx_intr_info) +
+ t4_handle_intr_status(adapter, MPS_TX_INT_CAUSE,
+ mps_tx_intr_info) +
+ t4_handle_intr_status(adapter, MPS_TRC_INT_CAUSE,
+ mps_trc_intr_info) +
+ t4_handle_intr_status(adapter, MPS_STAT_PERR_INT_CAUSE_SRAM,
+ mps_stat_sram_intr_info) +
+ t4_handle_intr_status(adapter, MPS_STAT_PERR_INT_CAUSE_TX_FIFO,
+ mps_stat_tx_intr_info) +
+ t4_handle_intr_status(adapter, MPS_STAT_PERR_INT_CAUSE_RX_FIFO,
+ mps_stat_rx_intr_info) +
+ t4_handle_intr_status(adapter, MPS_CLS_INT_CAUSE,
+ mps_cls_intr_info);
+
+ t4_write_reg(adapter, MPS_INT_CAUSE, CLSINT | TRCINT |
+ RXINT | TXINT | STATINT);
+ t4_read_reg(adapter, MPS_INT_CAUSE); /* flush */
+ if (fat)
+ t4_fatal_err(adapter);
+}
+
+#define MEM_INT_MASK (PERR_INT_CAUSE | ECC_CE_INT_CAUSE | ECC_UE_INT_CAUSE)
+
+/*
+ * EDC/MC interrupt handler.
+ */
+static void mem_intr_handler(struct adapter *adapter, int idx)
+{
+ static const char name[3][5] = { "EDC0", "EDC1", "MC" };
+
+ unsigned int addr, cnt_addr, v;
+
+ if (idx <= MEM_EDC1) {
+ addr = EDC_REG(EDC_INT_CAUSE, idx);
+ cnt_addr = EDC_REG(EDC_ECC_STATUS, idx);
+ } else {
+ addr = MC_INT_CAUSE;
+ cnt_addr = MC_ECC_STATUS;
+ }
+
+ v = t4_read_reg(adapter, addr) & MEM_INT_MASK;
+ if (v & PERR_INT_CAUSE)
+ dev_alert(adapter->pdev_dev, "%s FIFO parity error\n",
+ name[idx]);
+ if (v & ECC_CE_INT_CAUSE) {
+ u32 cnt = ECC_CECNT_GET(t4_read_reg(adapter, cnt_addr));
+
+ t4_write_reg(adapter, cnt_addr, ECC_CECNT_MASK);
+ if (printk_ratelimit())
+ dev_warn(adapter->pdev_dev,
+ "%u %s correctable ECC data error%s\n",
+ cnt, name[idx], cnt > 1 ? "s" : "");
+ }
+ if (v & ECC_UE_INT_CAUSE)
+ dev_alert(adapter->pdev_dev,
+ "%s uncorrectable ECC data error\n", name[idx]);
+
+ t4_write_reg(adapter, addr, v);
+ if (v & (PERR_INT_CAUSE | ECC_UE_INT_CAUSE))
+ t4_fatal_err(adapter);
+}
+
+/*
+ * MA interrupt handler.
+ */
+static void ma_intr_handler(struct adapter *adap)
+{
+ u32 v, status = t4_read_reg(adap, MA_INT_CAUSE);
+
+ if (status & MEM_PERR_INT_CAUSE)
+ dev_alert(adap->pdev_dev,
+ "MA parity error, parity status %#x\n",
+ t4_read_reg(adap, MA_PARITY_ERROR_STATUS));
+ if (status & MEM_WRAP_INT_CAUSE) {
+ v = t4_read_reg(adap, MA_INT_WRAP_STATUS);
+ dev_alert(adap->pdev_dev, "MA address wrap-around error by "
+ "client %u to address %#x\n",
+ MEM_WRAP_CLIENT_NUM_GET(v),
+ MEM_WRAP_ADDRESS_GET(v) << 4);
+ }
+ t4_write_reg(adap, MA_INT_CAUSE, status);
+ t4_fatal_err(adap);
+}
+
+/*
+ * SMB interrupt handler.
+ */
+static void smb_intr_handler(struct adapter *adap)
+{
+ static struct intr_info smb_intr_info[] = {
+ { MSTTXFIFOPARINT, "SMB master Tx FIFO parity error", -1, 1 },
+ { MSTRXFIFOPARINT, "SMB master Rx FIFO parity error", -1, 1 },
+ { SLVFIFOPARINT, "SMB slave FIFO parity error", -1, 1 },
+ { 0 }
+ };
+
+ if (t4_handle_intr_status(adap, SMB_INT_CAUSE, smb_intr_info))
+ t4_fatal_err(adap);
+}
+
+/*
+ * NC-SI interrupt handler.
+ */
+static void ncsi_intr_handler(struct adapter *adap)
+{
+ static struct intr_info ncsi_intr_info[] = {
+ { CIM_DM_PRTY_ERR, "NC-SI CIM parity error", -1, 1 },
+ { MPS_DM_PRTY_ERR, "NC-SI MPS parity error", -1, 1 },
+ { TXFIFO_PRTY_ERR, "NC-SI Tx FIFO parity error", -1, 1 },
+ { RXFIFO_PRTY_ERR, "NC-SI Rx FIFO parity error", -1, 1 },
+ { 0 }
+ };
+
+ if (t4_handle_intr_status(adap, NCSI_INT_CAUSE, ncsi_intr_info))
+ t4_fatal_err(adap);
+}
+
+/*
+ * XGMAC interrupt handler.
+ */
+static void xgmac_intr_handler(struct adapter *adap, int port)
+{
+ u32 v = t4_read_reg(adap, PORT_REG(port, XGMAC_PORT_INT_CAUSE));
+
+ v &= TXFIFO_PRTY_ERR | RXFIFO_PRTY_ERR;
+ if (!v)
+ return;
+
+ if (v & TXFIFO_PRTY_ERR)
+ dev_alert(adap->pdev_dev, "XGMAC %d Tx FIFO parity error\n",
+ port);
+ if (v & RXFIFO_PRTY_ERR)
+ dev_alert(adap->pdev_dev, "XGMAC %d Rx FIFO parity error\n",
+ port);
+ t4_write_reg(adap, PORT_REG(port, XGMAC_PORT_INT_CAUSE), v);
+ t4_fatal_err(adap);
+}
+
+/*
+ * PL interrupt handler.
+ */
+static void pl_intr_handler(struct adapter *adap)
+{
+ static struct intr_info pl_intr_info[] = {
+ { FATALPERR, "T4 fatal parity error", -1, 1 },
+ { PERRVFID, "PL VFID_MAP parity error", -1, 1 },
+ { 0 }
+ };
+
+ if (t4_handle_intr_status(adap, PL_PL_INT_CAUSE, pl_intr_info))
+ t4_fatal_err(adap);
+}
+
+#define PF_INTR_MASK (PFSW | PFCIM)
+#define GLBL_INTR_MASK (CIM | MPS | PL | PCIE | MC | EDC0 | \
+ EDC1 | LE | TP | MA | PM_TX | PM_RX | ULP_RX | \
+ CPL_SWITCH | SGE | ULP_TX)
+
+/**
+ * t4_slow_intr_handler - control path interrupt handler
+ * @adapter: the adapter
+ *
+ * T4 interrupt handler for non-data global interrupt events, e.g., errors.
+ * The designation 'slow' is because it involves register reads, while
+ * data interrupts typically don't involve any MMIOs.
+ */
+int t4_slow_intr_handler(struct adapter *adapter)
+{
+ u32 cause = t4_read_reg(adapter, PL_INT_CAUSE);
+
+ if (!(cause & GLBL_INTR_MASK))
+ return 0;
+ if (cause & CIM)
+ cim_intr_handler(adapter);
+ if (cause & MPS)
+ mps_intr_handler(adapter);
+ if (cause & NCSI)
+ ncsi_intr_handler(adapter);
+ if (cause & PL)
+ pl_intr_handler(adapter);
+ if (cause & SMB)
+ smb_intr_handler(adapter);
+ if (cause & XGMAC0)
+ xgmac_intr_handler(adapter, 0);
+ if (cause & XGMAC1)
+ xgmac_intr_handler(adapter, 1);
+ if (cause & XGMAC_KR0)
+ xgmac_intr_handler(adapter, 2);
+ if (cause & XGMAC_KR1)
+ xgmac_intr_handler(adapter, 3);
+ if (cause & PCIE)
+ pcie_intr_handler(adapter);
+ if (cause & MC)
+ mem_intr_handler(adapter, MEM_MC);
+ if (cause & EDC0)
+ mem_intr_handler(adapter, MEM_EDC0);
+ if (cause & EDC1)
+ mem_intr_handler(adapter, MEM_EDC1);
+ if (cause & LE)
+ le_intr_handler(adapter);
+ if (cause & TP)
+ tp_intr_handler(adapter);
+ if (cause & MA)
+ ma_intr_handler(adapter);
+ if (cause & PM_TX)
+ pmtx_intr_handler(adapter);
+ if (cause & PM_RX)
+ pmrx_intr_handler(adapter);
+ if (cause & ULP_RX)
+ ulprx_intr_handler(adapter);
+ if (cause & CPL_SWITCH)
+ cplsw_intr_handler(adapter);
+ if (cause & SGE)
+ sge_intr_handler(adapter);
+ if (cause & ULP_TX)
+ ulptx_intr_handler(adapter);
+
+ /* Clear the interrupts just processed for which we are the master. */
+ t4_write_reg(adapter, PL_INT_CAUSE, cause & GLBL_INTR_MASK);
+ (void) t4_read_reg(adapter, PL_INT_CAUSE); /* flush */
+ return 1;
+}
+
+/**
+ * t4_intr_enable - enable interrupts
+ * @adapter: the adapter whose interrupts should be enabled
+ *
+ * Enable PF-specific interrupts for the calling function and the top-level
+ * interrupt concentrator for global interrupts. Interrupts are already
+ * enabled at each module, here we just enable the roots of the interrupt
+ * hierarchies.
+ *
+ * Note: this function should be called only when the driver manages
+ * non PF-specific interrupts from the various HW modules. Only one PCI
+ * function at a time should be doing this.
+ */
+void t4_intr_enable(struct adapter *adapter)
+{
+ u32 pf = SOURCEPF_GET(t4_read_reg(adapter, PL_WHOAMI));
+
+ t4_write_reg(adapter, SGE_INT_ENABLE3, ERR_CPL_EXCEED_IQE_SIZE |
+ ERR_INVALID_CIDX_INC | ERR_CPL_OPCODE_0 |
+ ERR_DROPPED_DB | ERR_DATA_CPL_ON_HIGH_QID1 |
+ ERR_DATA_CPL_ON_HIGH_QID0 | ERR_BAD_DB_PIDX3 |
+ ERR_BAD_DB_PIDX2 | ERR_BAD_DB_PIDX1 |
+ ERR_BAD_DB_PIDX0 | ERR_ING_CTXT_PRIO |
+ ERR_EGR_CTXT_PRIO | INGRESS_SIZE_ERR |
+ EGRESS_SIZE_ERR);
+ t4_write_reg(adapter, MYPF_REG(PL_PF_INT_ENABLE), PF_INTR_MASK);
+ t4_set_reg_field(adapter, PL_INT_MAP0, 0, 1 << pf);
+}
+
+/**
+ * t4_intr_disable - disable interrupts
+ * @adapter: the adapter whose interrupts should be disabled
+ *
+ * Disable interrupts. We only disable the top-level interrupt
+ * concentrators. The caller must be a PCI function managing global
+ * interrupts.
+ */
+void t4_intr_disable(struct adapter *adapter)
+{
+ u32 pf = SOURCEPF_GET(t4_read_reg(adapter, PL_WHOAMI));
+
+ t4_write_reg(adapter, MYPF_REG(PL_PF_INT_ENABLE), 0);
+ t4_set_reg_field(adapter, PL_INT_MAP0, 1 << pf, 0);
+}
+
+/**
+ * t4_intr_clear - clear all interrupts
+ * @adapter: the adapter whose interrupts should be cleared
+ *
+ * Clears all interrupts. The caller must be a PCI function managing
+ * global interrupts.
+ */
+void t4_intr_clear(struct adapter *adapter)
+{
+ static const unsigned int cause_reg[] = {
+ SGE_INT_CAUSE1, SGE_INT_CAUSE2, SGE_INT_CAUSE3,
+ PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS,
+ PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS,
+ PCIE_NONFAT_ERR, PCIE_INT_CAUSE,
+ MC_INT_CAUSE,
+ MA_INT_WRAP_STATUS, MA_PARITY_ERROR_STATUS, MA_INT_CAUSE,
+ EDC_INT_CAUSE, EDC_REG(EDC_INT_CAUSE, 1),
+ CIM_HOST_INT_CAUSE, CIM_HOST_UPACC_INT_CAUSE,
+ MYPF_REG(CIM_PF_HOST_INT_CAUSE),
+ TP_INT_CAUSE,
+ ULP_RX_INT_CAUSE, ULP_TX_INT_CAUSE,
+ PM_RX_INT_CAUSE, PM_TX_INT_CAUSE,
+ MPS_RX_PERR_INT_CAUSE,
+ CPL_INTR_CAUSE,
+ MYPF_REG(PL_PF_INT_CAUSE),
+ PL_PL_INT_CAUSE,
+ LE_DB_INT_CAUSE,
+ };
+
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(cause_reg); ++i)
+ t4_write_reg(adapter, cause_reg[i], 0xffffffff);
+
+ t4_write_reg(adapter, PL_INT_CAUSE, GLBL_INTR_MASK);
+ (void) t4_read_reg(adapter, PL_INT_CAUSE); /* flush */
+}
+
+/**
+ * hash_mac_addr - return the hash value of a MAC address
+ * @addr: the 48-bit Ethernet MAC address
+ *
+ * Hashes a MAC address according to the hash function used by HW inexact
+ * (hash) address matching.
+ */
+static int hash_mac_addr(const u8 *addr)
+{
+ u32 a = ((u32)addr[0] << 16) | ((u32)addr[1] << 8) | addr[2];
+ u32 b = ((u32)addr[3] << 16) | ((u32)addr[4] << 8) | addr[5];
+ a ^= b;
+ a ^= (a >> 12);
+ a ^= (a >> 6);
+ return a & 0x3f;
+}
+
+/**
+ * t4_config_rss_range - configure a portion of the RSS mapping table
+ * @adapter: the adapter
+ * @mbox: mbox to use for the FW command
+ * @viid: virtual interface whose RSS subtable is to be written
+ * @start: start entry in the table to write
+ * @n: how many table entries to write
+ * @rspq: values for the response queue lookup table
+ * @nrspq: number of values in @rspq
+ *
+ * Programs the selected part of the VI's RSS mapping table with the
+ * provided values. If @nrspq < @n the supplied values are used repeatedly
+ * until the full table range is populated.
+ *
+ * The caller must ensure the values in @rspq are in the range allowed for
+ * @viid.
+ */
+int t4_config_rss_range(struct adapter *adapter, int mbox, unsigned int viid,
+ int start, int n, const u16 *rspq, unsigned int nrspq)
+{
+ int ret;
+ const u16 *rsp = rspq;
+ const u16 *rsp_end = rspq + nrspq;
+ struct fw_rss_ind_tbl_cmd cmd;
+
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.op_to_viid = htonl(FW_CMD_OP(FW_RSS_IND_TBL_CMD) |
+ FW_CMD_REQUEST | FW_CMD_WRITE |
+ FW_RSS_IND_TBL_CMD_VIID(viid));
+ cmd.retval_len16 = htonl(FW_LEN16(cmd));
+
+ /* each fw_rss_ind_tbl_cmd takes up to 32 entries */
+ while (n > 0) {
+ int nq = min(n, 32);
+ __be32 *qp = &cmd.iq0_to_iq2;
+
+ cmd.niqid = htons(nq);
+ cmd.startidx = htons(start);
+
+ start += nq;
+ n -= nq;
+
+ while (nq > 0) {
+ unsigned int v;
+
+ v = FW_RSS_IND_TBL_CMD_IQ0(*rsp);
+ if (++rsp >= rsp_end)
+ rsp = rspq;
+ v |= FW_RSS_IND_TBL_CMD_IQ1(*rsp);
+ if (++rsp >= rsp_end)
+ rsp = rspq;
+ v |= FW_RSS_IND_TBL_CMD_IQ2(*rsp);
+ if (++rsp >= rsp_end)
+ rsp = rspq;
+
+ *qp++ = htonl(v);
+ nq -= 3;
+ }
+
+ ret = t4_wr_mbox(adapter, mbox, &cmd, sizeof(cmd), NULL);
+ if (ret)
+ return ret;
+ }
+ return 0;
+}
+
+/**
+ * t4_config_glbl_rss - configure the global RSS mode
+ * @adapter: the adapter
+ * @mbox: mbox to use for the FW command
+ * @mode: global RSS mode
+ * @flags: mode-specific flags
+ *
+ * Sets the global RSS mode.
+ */
+int t4_config_glbl_rss(struct adapter *adapter, int mbox, unsigned int mode,
+ unsigned int flags)
+{
+ struct fw_rss_glb_config_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_write = htonl(FW_CMD_OP(FW_RSS_GLB_CONFIG_CMD) |
+ FW_CMD_REQUEST | FW_CMD_WRITE);
+ c.retval_len16 = htonl(FW_LEN16(c));
+ if (mode == FW_RSS_GLB_CONFIG_CMD_MODE_MANUAL) {
+ c.u.manual.mode_pkd = htonl(FW_RSS_GLB_CONFIG_CMD_MODE(mode));
+ } else if (mode == FW_RSS_GLB_CONFIG_CMD_MODE_BASICVIRTUAL) {
+ c.u.basicvirtual.mode_pkd =
+ htonl(FW_RSS_GLB_CONFIG_CMD_MODE(mode));
+ c.u.basicvirtual.synmapen_to_hashtoeplitz = htonl(flags);
+ } else
+ return -EINVAL;
+ return t4_wr_mbox(adapter, mbox, &c, sizeof(c), NULL);
+}
+
+/* Read an RSS table row */
+static int rd_rss_row(struct adapter *adap, int row, u32 *val)
+{
+ t4_write_reg(adap, TP_RSS_LKP_TABLE, 0xfff00000 | row);
+ return t4_wait_op_done_val(adap, TP_RSS_LKP_TABLE, LKPTBLROWVLD, 1,
+ 5, 0, val);
+}
+
+/**
+ * t4_read_rss - read the contents of the RSS mapping table
+ * @adapter: the adapter
+ * @map: holds the contents of the RSS mapping table
+ *
+ * Reads the contents of the RSS hash->queue mapping table.
+ */
+int t4_read_rss(struct adapter *adapter, u16 *map)
+{
+ u32 val;
+ int i, ret;
+
+ for (i = 0; i < RSS_NENTRIES / 2; ++i) {
+ ret = rd_rss_row(adapter, i, &val);
+ if (ret)
+ return ret;
+ *map++ = LKPTBLQUEUE0_GET(val);
+ *map++ = LKPTBLQUEUE1_GET(val);
+ }
+ return 0;
+}
+
+/**
+ * t4_tp_get_tcp_stats - read TP's TCP MIB counters
+ * @adap: the adapter
+ * @v4: holds the TCP/IP counter values
+ * @v6: holds the TCP/IPv6 counter values
+ *
+ * Returns the values of TP's TCP/IP and TCP/IPv6 MIB counters.
+ * Either @v4 or @v6 may be %NULL to skip the corresponding stats.
+ */
+void t4_tp_get_tcp_stats(struct adapter *adap, struct tp_tcp_stats *v4,
+ struct tp_tcp_stats *v6)
+{
+ u32 val[TP_MIB_TCP_RXT_SEG_LO - TP_MIB_TCP_OUT_RST + 1];
+
+#define STAT_IDX(x) ((TP_MIB_TCP_##x) - TP_MIB_TCP_OUT_RST)
+#define STAT(x) val[STAT_IDX(x)]
+#define STAT64(x) (((u64)STAT(x##_HI) << 32) | STAT(x##_LO))
+
+ if (v4) {
+ t4_read_indirect(adap, TP_MIB_INDEX, TP_MIB_DATA, val,
+ ARRAY_SIZE(val), TP_MIB_TCP_OUT_RST);
+ v4->tcpOutRsts = STAT(OUT_RST);
+ v4->tcpInSegs = STAT64(IN_SEG);
+ v4->tcpOutSegs = STAT64(OUT_SEG);
+ v4->tcpRetransSegs = STAT64(RXT_SEG);
+ }
+ if (v6) {
+ t4_read_indirect(adap, TP_MIB_INDEX, TP_MIB_DATA, val,
+ ARRAY_SIZE(val), TP_MIB_TCP_V6OUT_RST);
+ v6->tcpOutRsts = STAT(OUT_RST);
+ v6->tcpInSegs = STAT64(IN_SEG);
+ v6->tcpOutSegs = STAT64(OUT_SEG);
+ v6->tcpRetransSegs = STAT64(RXT_SEG);
+ }
+#undef STAT64
+#undef STAT
+#undef STAT_IDX
+}
+
+/**
+ * t4_tp_get_err_stats - read TP's error MIB counters
+ * @adap: the adapter
+ * @st: holds the counter values
+ *
+ * Returns the values of TP's error counters.
+ */
+void t4_tp_get_err_stats(struct adapter *adap, struct tp_err_stats *st)
+{
+ t4_read_indirect(adap, TP_MIB_INDEX, TP_MIB_DATA, st->macInErrs,
+ 12, TP_MIB_MAC_IN_ERR_0);
+ t4_read_indirect(adap, TP_MIB_INDEX, TP_MIB_DATA, st->tnlCongDrops,
+ 8, TP_MIB_TNL_CNG_DROP_0);
+ t4_read_indirect(adap, TP_MIB_INDEX, TP_MIB_DATA, st->tnlTxDrops,
+ 4, TP_MIB_TNL_DROP_0);
+ t4_read_indirect(adap, TP_MIB_INDEX, TP_MIB_DATA, st->ofldVlanDrops,
+ 4, TP_MIB_OFD_VLN_DROP_0);
+ t4_read_indirect(adap, TP_MIB_INDEX, TP_MIB_DATA, st->tcp6InErrs,
+ 4, TP_MIB_TCP_V6IN_ERR_0);
+ t4_read_indirect(adap, TP_MIB_INDEX, TP_MIB_DATA, &st->ofldNoNeigh,
+ 2, TP_MIB_OFD_ARP_DROP);
+}
+
+/**
+ * t4_read_mtu_tbl - returns the values in the HW path MTU table
+ * @adap: the adapter
+ * @mtus: where to store the MTU values
+ * @mtu_log: where to store the MTU base-2 log (may be %NULL)
+ *
+ * Reads the HW path MTU table.
+ */
+void t4_read_mtu_tbl(struct adapter *adap, u16 *mtus, u8 *mtu_log)
+{
+ u32 v;
+ int i;
+
+ for (i = 0; i < NMTUS; ++i) {
+ t4_write_reg(adap, TP_MTU_TABLE,
+ MTUINDEX(0xff) | MTUVALUE(i));
+ v = t4_read_reg(adap, TP_MTU_TABLE);
+ mtus[i] = MTUVALUE_GET(v);
+ if (mtu_log)
+ mtu_log[i] = MTUWIDTH_GET(v);
+ }
+}
+
+/**
+ * init_cong_ctrl - initialize congestion control parameters
+ * @a: the alpha values for congestion control
+ * @b: the beta values for congestion control
+ *
+ * Initialize the congestion control parameters.
+ */
+static void __devinit init_cong_ctrl(unsigned short *a, unsigned short *b)
+{
+ a[0] = a[1] = a[2] = a[3] = a[4] = a[5] = a[6] = a[7] = a[8] = 1;
+ a[9] = 2;
+ a[10] = 3;
+ a[11] = 4;
+ a[12] = 5;
+ a[13] = 6;
+ a[14] = 7;
+ a[15] = 8;
+ a[16] = 9;
+ a[17] = 10;
+ a[18] = 14;
+ a[19] = 17;
+ a[20] = 21;
+ a[21] = 25;
+ a[22] = 30;
+ a[23] = 35;
+ a[24] = 45;
+ a[25] = 60;
+ a[26] = 80;
+ a[27] = 100;
+ a[28] = 200;
+ a[29] = 300;
+ a[30] = 400;
+ a[31] = 500;
+
+ b[0] = b[1] = b[2] = b[3] = b[4] = b[5] = b[6] = b[7] = b[8] = 0;
+ b[9] = b[10] = 1;
+ b[11] = b[12] = 2;
+ b[13] = b[14] = b[15] = b[16] = 3;
+ b[17] = b[18] = b[19] = b[20] = b[21] = 4;
+ b[22] = b[23] = b[24] = b[25] = b[26] = b[27] = 5;
+ b[28] = b[29] = 6;
+ b[30] = b[31] = 7;
+}
+
+/* The minimum additive increment value for the congestion control table */
+#define CC_MIN_INCR 2U
+
+/**
+ * t4_load_mtus - write the MTU and congestion control HW tables
+ * @adap: the adapter
+ * @mtus: the values for the MTU table
+ * @alpha: the values for the congestion control alpha parameter
+ * @beta: the values for the congestion control beta parameter
+ *
+ * Write the HW MTU table with the supplied MTUs and the high-speed
+ * congestion control table with the supplied alpha, beta, and MTUs.
+ * We write the two tables together because the additive increments
+ * depend on the MTUs.
+ */
+void t4_load_mtus(struct adapter *adap, const unsigned short *mtus,
+ const unsigned short *alpha, const unsigned short *beta)
+{
+ static const unsigned int avg_pkts[NCCTRL_WIN] = {
+ 2, 6, 10, 14, 20, 28, 40, 56, 80, 112, 160, 224, 320, 448, 640,
+ 896, 1281, 1792, 2560, 3584, 5120, 7168, 10240, 14336, 20480,
+ 28672, 40960, 57344, 81920, 114688, 163840, 229376
+ };
+
+ unsigned int i, w;
+
+ for (i = 0; i < NMTUS; ++i) {
+ unsigned int mtu = mtus[i];
+ unsigned int log2 = fls(mtu);
+
+ if (!(mtu & ((1 << log2) >> 2))) /* round */
+ log2--;
+ t4_write_reg(adap, TP_MTU_TABLE, MTUINDEX(i) |
+ MTUWIDTH(log2) | MTUVALUE(mtu));
+
+ for (w = 0; w < NCCTRL_WIN; ++w) {
+ unsigned int inc;
+
+ inc = max(((mtu - 40) * alpha[w]) / avg_pkts[w],
+ CC_MIN_INCR);
+
+ t4_write_reg(adap, TP_CCTRL_TABLE, (i << 21) |
+ (w << 16) | (beta[w] << 13) | inc);
+ }
+ }
+}
+
+/**
+ * t4_set_trace_filter - configure one of the tracing filters
+ * @adap: the adapter
+ * @tp: the desired trace filter parameters
+ * @idx: which filter to configure
+ * @enable: whether to enable or disable the filter
+ *
+ * Configures one of the tracing filters available in HW. If @enable is
+ * %0 @tp is not examined and may be %NULL.
+ */
+int t4_set_trace_filter(struct adapter *adap, const struct trace_params *tp,
+ int idx, int enable)
+{
+ int i, ofst = idx * 4;
+ u32 data_reg, mask_reg, cfg;
+ u32 multitrc = TRCMULTIFILTER;
+
+ if (!enable) {
+ t4_write_reg(adap, MPS_TRC_FILTER_MATCH_CTL_A + ofst, 0);
+ goto out;
+ }
+
+ if (tp->port > 11 || tp->invert > 1 || tp->skip_len > 0x1f ||
+ tp->skip_ofst > 0x1f || tp->min_len > 0x1ff ||
+ tp->snap_len > 9600 || (idx && tp->snap_len > 256))
+ return -EINVAL;
+
+ if (tp->snap_len > 256) { /* must be tracer 0 */
+ if ((t4_read_reg(adap, MPS_TRC_FILTER_MATCH_CTL_A + 4) |
+ t4_read_reg(adap, MPS_TRC_FILTER_MATCH_CTL_A + 8) |
+ t4_read_reg(adap, MPS_TRC_FILTER_MATCH_CTL_A + 12)) & TFEN)
+ return -EINVAL; /* other tracers are enabled */
+ multitrc = 0;
+ } else if (idx) {
+ i = t4_read_reg(adap, MPS_TRC_FILTER_MATCH_CTL_B);
+ if (TFCAPTUREMAX_GET(i) > 256 &&
+ (t4_read_reg(adap, MPS_TRC_FILTER_MATCH_CTL_A) & TFEN))
+ return -EINVAL;
+ }
+
+ /* stop the tracer we'll be changing */
+ t4_write_reg(adap, MPS_TRC_FILTER_MATCH_CTL_A + ofst, 0);
+
+ /* disable tracing globally if running in the wrong single/multi mode */
+ cfg = t4_read_reg(adap, MPS_TRC_CFG);
+ if ((cfg & TRCEN) && multitrc != (cfg & TRCMULTIFILTER)) {
+ t4_write_reg(adap, MPS_TRC_CFG, cfg ^ TRCEN);
+ t4_read_reg(adap, MPS_TRC_CFG); /* flush */
+ msleep(1);
+ if (!(t4_read_reg(adap, MPS_TRC_CFG) & TRCFIFOEMPTY))
+ return -ETIMEDOUT;
+ }
+ /*
+ * At this point either the tracing is enabled and in the right mode or
+ * disabled.
+ */
+
+ idx *= (MPS_TRC_FILTER1_MATCH - MPS_TRC_FILTER0_MATCH);
+ data_reg = MPS_TRC_FILTER0_MATCH + idx;
+ mask_reg = MPS_TRC_FILTER0_DONT_CARE + idx;
+
+ for (i = 0; i < TRACE_LEN / 4; i++, data_reg += 4, mask_reg += 4) {
+ t4_write_reg(adap, data_reg, tp->data[i]);
+ t4_write_reg(adap, mask_reg, ~tp->mask[i]);
+ }
+ t4_write_reg(adap, MPS_TRC_FILTER_MATCH_CTL_B + ofst,
+ TFCAPTUREMAX(tp->snap_len) |
+ TFMINPKTSIZE(tp->min_len));
+ t4_write_reg(adap, MPS_TRC_FILTER_MATCH_CTL_A + ofst,
+ TFOFFSET(tp->skip_ofst) | TFLENGTH(tp->skip_len) |
+ TFPORT(tp->port) | TFEN |
+ (tp->invert ? TFINVERTMATCH : 0));
+
+ cfg &= ~TRCMULTIFILTER;
+ t4_write_reg(adap, MPS_TRC_CFG, cfg | TRCEN | multitrc);
+out: t4_read_reg(adap, MPS_TRC_CFG); /* flush */
+ return 0;
+}
+
+/**
+ * t4_get_trace_filter - query one of the tracing filters
+ * @adap: the adapter
+ * @tp: the current trace filter parameters
+ * @idx: which trace filter to query
+ * @enabled: non-zero if the filter is enabled
+ *
+ * Returns the current settings of one of the HW tracing filters.
+ */
+void t4_get_trace_filter(struct adapter *adap, struct trace_params *tp, int idx,
+ int *enabled)
+{
+ u32 ctla, ctlb;
+ int i, ofst = idx * 4;
+ u32 data_reg, mask_reg;
+
+ ctla = t4_read_reg(adap, MPS_TRC_FILTER_MATCH_CTL_A + ofst);
+ ctlb = t4_read_reg(adap, MPS_TRC_FILTER_MATCH_CTL_B + ofst);
+
+ *enabled = !!(ctla & TFEN);
+ tp->snap_len = TFCAPTUREMAX_GET(ctlb);
+ tp->min_len = TFMINPKTSIZE_GET(ctlb);
+ tp->skip_ofst = TFOFFSET_GET(ctla);
+ tp->skip_len = TFLENGTH_GET(ctla);
+ tp->invert = !!(ctla & TFINVERTMATCH);
+ tp->port = TFPORT_GET(ctla);
+
+ ofst = (MPS_TRC_FILTER1_MATCH - MPS_TRC_FILTER0_MATCH) * idx;
+ data_reg = MPS_TRC_FILTER0_MATCH + ofst;
+ mask_reg = MPS_TRC_FILTER0_DONT_CARE + ofst;
+
+ for (i = 0; i < TRACE_LEN / 4; i++, data_reg += 4, mask_reg += 4) {
+ tp->mask[i] = ~t4_read_reg(adap, mask_reg);
+ tp->data[i] = t4_read_reg(adap, data_reg) & tp->mask[i];
+ }
+}
+
+/**
+ * get_mps_bg_map - return the buffer groups associated with a port
+ * @adap: the adapter
+ * @idx: the port index
+ *
+ * Returns a bitmap indicating which MPS buffer groups are associated
+ * with the given port. Bit i is set if buffer group i is used by the
+ * port.
+ */
+static unsigned int get_mps_bg_map(struct adapter *adap, int idx)
+{
+ u32 n = NUMPORTS_GET(t4_read_reg(adap, MPS_CMN_CTL));
+
+ if (n == 0)
+ return idx == 0 ? 0xf : 0;
+ if (n == 1)
+ return idx < 2 ? (3 << (2 * idx)) : 0;
+ return 1 << idx;
+}
+
+/**
+ * t4_get_port_stats - collect port statistics
+ * @adap: the adapter
+ * @idx: the port index
+ * @p: the stats structure to fill
+ *
+ * Collect statistics related to the given port from HW.
+ */
+void t4_get_port_stats(struct adapter *adap, int idx, struct port_stats *p)
+{
+ u32 bgmap = get_mps_bg_map(adap, idx);
+
+#define GET_STAT(name) \
+ t4_read_reg64(adap, PORT_REG(idx, MPS_PORT_STAT_##name##_L))
+#define GET_STAT_COM(name) t4_read_reg64(adap, MPS_STAT_##name##_L)
+
+ p->tx_octets = GET_STAT(TX_PORT_BYTES);
+ p->tx_frames = GET_STAT(TX_PORT_FRAMES);
+ p->tx_bcast_frames = GET_STAT(TX_PORT_BCAST);
+ p->tx_mcast_frames = GET_STAT(TX_PORT_MCAST);
+ p->tx_ucast_frames = GET_STAT(TX_PORT_UCAST);
+ p->tx_error_frames = GET_STAT(TX_PORT_ERROR);
+ p->tx_frames_64 = GET_STAT(TX_PORT_64B);
+ p->tx_frames_65_127 = GET_STAT(TX_PORT_65B_127B);
+ p->tx_frames_128_255 = GET_STAT(TX_PORT_128B_255B);
+ p->tx_frames_256_511 = GET_STAT(TX_PORT_256B_511B);
+ p->tx_frames_512_1023 = GET_STAT(TX_PORT_512B_1023B);
+ p->tx_frames_1024_1518 = GET_STAT(TX_PORT_1024B_1518B);
+ p->tx_frames_1519_max = GET_STAT(TX_PORT_1519B_MAX);
+ p->tx_drop = GET_STAT(TX_PORT_DROP);
+ p->tx_pause = GET_STAT(TX_PORT_PAUSE);
+ p->tx_ppp0 = GET_STAT(TX_PORT_PPP0);
+ p->tx_ppp1 = GET_STAT(TX_PORT_PPP1);
+ p->tx_ppp2 = GET_STAT(TX_PORT_PPP2);
+ p->tx_ppp3 = GET_STAT(TX_PORT_PPP3);
+ p->tx_ppp4 = GET_STAT(TX_PORT_PPP4);
+ p->tx_ppp5 = GET_STAT(TX_PORT_PPP5);
+ p->tx_ppp6 = GET_STAT(TX_PORT_PPP6);
+ p->tx_ppp7 = GET_STAT(TX_PORT_PPP7);
+
+ p->rx_octets = GET_STAT(RX_PORT_BYTES);
+ p->rx_frames = GET_STAT(RX_PORT_FRAMES);
+ p->rx_bcast_frames = GET_STAT(RX_PORT_BCAST);
+ p->rx_mcast_frames = GET_STAT(RX_PORT_MCAST);
+ p->rx_ucast_frames = GET_STAT(RX_PORT_UCAST);
+ p->rx_too_long = GET_STAT(RX_PORT_MTU_ERROR);
+ p->rx_jabber = GET_STAT(RX_PORT_MTU_CRC_ERROR);
+ p->rx_fcs_err = GET_STAT(RX_PORT_CRC_ERROR);
+ p->rx_len_err = GET_STAT(RX_PORT_LEN_ERROR);
+ p->rx_symbol_err = GET_STAT(RX_PORT_SYM_ERROR);
+ p->rx_runt = GET_STAT(RX_PORT_LESS_64B);
+ p->rx_frames_64 = GET_STAT(RX_PORT_64B);
+ p->rx_frames_65_127 = GET_STAT(RX_PORT_65B_127B);
+ p->rx_frames_128_255 = GET_STAT(RX_PORT_128B_255B);
+ p->rx_frames_256_511 = GET_STAT(RX_PORT_256B_511B);
+ p->rx_frames_512_1023 = GET_STAT(RX_PORT_512B_1023B);
+ p->rx_frames_1024_1518 = GET_STAT(RX_PORT_1024B_1518B);
+ p->rx_frames_1519_max = GET_STAT(RX_PORT_1519B_MAX);
+ p->rx_pause = GET_STAT(RX_PORT_PAUSE);
+ p->rx_ppp0 = GET_STAT(RX_PORT_PPP0);
+ p->rx_ppp1 = GET_STAT(RX_PORT_PPP1);
+ p->rx_ppp2 = GET_STAT(RX_PORT_PPP2);
+ p->rx_ppp3 = GET_STAT(RX_PORT_PPP3);
+ p->rx_ppp4 = GET_STAT(RX_PORT_PPP4);
+ p->rx_ppp5 = GET_STAT(RX_PORT_PPP5);
+ p->rx_ppp6 = GET_STAT(RX_PORT_PPP6);
+ p->rx_ppp7 = GET_STAT(RX_PORT_PPP7);
+
+ p->rx_ovflow0 = (bgmap & 1) ? GET_STAT_COM(RX_BG_0_MAC_DROP_FRAME) : 0;
+ p->rx_ovflow1 = (bgmap & 2) ? GET_STAT_COM(RX_BG_1_MAC_DROP_FRAME) : 0;
+ p->rx_ovflow2 = (bgmap & 4) ? GET_STAT_COM(RX_BG_2_MAC_DROP_FRAME) : 0;
+ p->rx_ovflow3 = (bgmap & 8) ? GET_STAT_COM(RX_BG_3_MAC_DROP_FRAME) : 0;
+ p->rx_trunc0 = (bgmap & 1) ? GET_STAT_COM(RX_BG_0_MAC_TRUNC_FRAME) : 0;
+ p->rx_trunc1 = (bgmap & 2) ? GET_STAT_COM(RX_BG_1_MAC_TRUNC_FRAME) : 0;
+ p->rx_trunc2 = (bgmap & 4) ? GET_STAT_COM(RX_BG_2_MAC_TRUNC_FRAME) : 0;
+ p->rx_trunc3 = (bgmap & 8) ? GET_STAT_COM(RX_BG_3_MAC_TRUNC_FRAME) : 0;
+
+#undef GET_STAT
+#undef GET_STAT_COM
+}
+
+/**
+ * t4_get_lb_stats - collect loopback port statistics
+ * @adap: the adapter
+ * @idx: the loopback port index
+ * @p: the stats structure to fill
+ *
+ * Return HW statistics for the given loopback port.
+ */
+void t4_get_lb_stats(struct adapter *adap, int idx, struct lb_port_stats *p)
+{
+ u32 bgmap = get_mps_bg_map(adap, idx);
+
+#define GET_STAT(name) \
+ t4_read_reg64(adap, PORT_REG(idx, MPS_PORT_STAT_LB_PORT_##name##_L))
+#define GET_STAT_COM(name) t4_read_reg64(adap, MPS_STAT_##name##_L)
+
+ p->octets = GET_STAT(BYTES);
+ p->frames = GET_STAT(FRAMES);
+ p->bcast_frames = GET_STAT(BCAST);
+ p->mcast_frames = GET_STAT(MCAST);
+ p->ucast_frames = GET_STAT(UCAST);
+ p->error_frames = GET_STAT(ERROR);
+
+ p->frames_64 = GET_STAT(64B);
+ p->frames_65_127 = GET_STAT(65B_127B);
+ p->frames_128_255 = GET_STAT(128B_255B);
+ p->frames_256_511 = GET_STAT(256B_511B);
+ p->frames_512_1023 = GET_STAT(512B_1023B);
+ p->frames_1024_1518 = GET_STAT(1024B_1518B);
+ p->frames_1519_max = GET_STAT(1519B_MAX);
+ p->drop = t4_read_reg(adap, PORT_REG(idx,
+ MPS_PORT_STAT_LB_PORT_DROP_FRAMES));
+
+ p->ovflow0 = (bgmap & 1) ? GET_STAT_COM(RX_BG_0_LB_DROP_FRAME) : 0;
+ p->ovflow1 = (bgmap & 2) ? GET_STAT_COM(RX_BG_1_LB_DROP_FRAME) : 0;
+ p->ovflow2 = (bgmap & 4) ? GET_STAT_COM(RX_BG_2_LB_DROP_FRAME) : 0;
+ p->ovflow3 = (bgmap & 8) ? GET_STAT_COM(RX_BG_3_LB_DROP_FRAME) : 0;
+ p->trunc0 = (bgmap & 1) ? GET_STAT_COM(RX_BG_0_LB_TRUNC_FRAME) : 0;
+ p->trunc1 = (bgmap & 2) ? GET_STAT_COM(RX_BG_1_LB_TRUNC_FRAME) : 0;
+ p->trunc2 = (bgmap & 4) ? GET_STAT_COM(RX_BG_2_LB_TRUNC_FRAME) : 0;
+ p->trunc3 = (bgmap & 8) ? GET_STAT_COM(RX_BG_3_LB_TRUNC_FRAME) : 0;
+
+#undef GET_STAT
+#undef GET_STAT_COM
+}
+
+/**
+ * t4_wol_magic_enable - enable/disable magic packet WoL
+ * @adap: the adapter
+ * @port: the physical port index
+ * @addr: MAC address expected in magic packets, %NULL to disable
+ *
+ * Enables/disables magic packet wake-on-LAN for the selected port.
+ */
+void t4_wol_magic_enable(struct adapter *adap, unsigned int port,
+ const u8 *addr)
+{
+ if (addr) {
+ t4_write_reg(adap, PORT_REG(port, XGMAC_PORT_MAGIC_MACID_LO),
+ (addr[2] << 24) | (addr[3] << 16) |
+ (addr[4] << 8) | addr[5]);
+ t4_write_reg(adap, PORT_REG(port, XGMAC_PORT_MAGIC_MACID_HI),
+ (addr[0] << 8) | addr[1]);
+ }
+ t4_set_reg_field(adap, PORT_REG(port, XGMAC_PORT_CFG2), MAGICEN,
+ addr ? MAGICEN : 0);
+}
+
+/**
+ * t4_wol_pat_enable - enable/disable pattern-based WoL
+ * @adap: the adapter
+ * @port: the physical port index
+ * @map: bitmap of which HW pattern filters to set
+ * @mask0: byte mask for bytes 0-63 of a packet
+ * @mask1: byte mask for bytes 64-127 of a packet
+ * @crc: Ethernet CRC for selected bytes
+ * @enable: enable/disable switch
+ *
+ * Sets the pattern filters indicated in @map to mask out the bytes
+ * specified in @mask0/@mask1 in received packets and compare the CRC of
+ * the resulting packet against @crc. If @enable is %true pattern-based
+ * WoL is enabled, otherwise disabled.
+ */
+int t4_wol_pat_enable(struct adapter *adap, unsigned int port, unsigned int map,
+ u64 mask0, u64 mask1, unsigned int crc, bool enable)
+{
+ int i;
+
+ if (!enable) {
+ t4_set_reg_field(adap, PORT_REG(port, XGMAC_PORT_CFG2),
+ PATEN, 0);
+ return 0;
+ }
+ if (map > 0xff)
+ return -EINVAL;
+
+#define EPIO_REG(name) PORT_REG(port, XGMAC_PORT_EPIO_##name)
+
+ t4_write_reg(adap, EPIO_REG(DATA1), mask0 >> 32);
+ t4_write_reg(adap, EPIO_REG(DATA2), mask1);
+ t4_write_reg(adap, EPIO_REG(DATA3), mask1 >> 32);
+
+ for (i = 0; i < NWOL_PAT; i++, map >>= 1) {
+ if (!(map & 1))
+ continue;
+
+ /* write byte masks */
+ t4_write_reg(adap, EPIO_REG(DATA0), mask0);
+ t4_write_reg(adap, EPIO_REG(OP), ADDRESS(i) | EPIOWR);
+ t4_read_reg(adap, EPIO_REG(OP)); /* flush */
+ if (t4_read_reg(adap, EPIO_REG(OP)) & BUSY)
+ return -ETIMEDOUT;
+
+ /* write CRC */
+ t4_write_reg(adap, EPIO_REG(DATA0), crc);
+ t4_write_reg(adap, EPIO_REG(OP), ADDRESS(i + 32) | EPIOWR);
+ t4_read_reg(adap, EPIO_REG(OP)); /* flush */
+ if (t4_read_reg(adap, EPIO_REG(OP)) & BUSY)
+ return -ETIMEDOUT;
+ }
+#undef EPIO_REG
+
+ t4_set_reg_field(adap, PORT_REG(port, XGMAC_PORT_CFG2), 0, PATEN);
+ return 0;
+}
+
+#define INIT_CMD(var, cmd, rd_wr) \
+ (var).op_to_write = htonl(FW_CMD_OP(FW_##cmd##_CMD) | \
+ FW_CMD_REQUEST | FW_CMD_##rd_wr); \
+ (var).retval_len16 = htonl(FW_LEN16(var))
+
+/**
+ * t4_mdio_rd - read a PHY register through MDIO
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @phy_addr: the PHY address
+ * @mmd: the PHY MMD to access (0 for clause 22 PHYs)
+ * @reg: the register to read
+ * @valp: where to store the value
+ *
+ * Issues a FW command through the given mailbox to read a PHY register.
+ */
+int t4_mdio_rd(struct adapter *adap, unsigned int mbox, unsigned int phy_addr,
+ unsigned int mmd, unsigned int reg, u16 *valp)
+{
+ int ret;
+ struct fw_ldst_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_addrspace = htonl(FW_CMD_OP(FW_LDST_CMD) | FW_CMD_REQUEST |
+ FW_CMD_READ | FW_LDST_CMD_ADDRSPACE(FW_LDST_ADDRSPC_MDIO));
+ c.cycles_to_len16 = htonl(FW_LEN16(c));
+ c.u.mdio.paddr_mmd = htons(FW_LDST_CMD_PADDR(phy_addr) |
+ FW_LDST_CMD_MMD(mmd));
+ c.u.mdio.raddr = htons(reg);
+
+ ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c);
+ if (ret == 0)
+ *valp = ntohs(c.u.mdio.rval);
+ return ret;
+}
+
+/**
+ * t4_mdio_wr - write a PHY register through MDIO
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @phy_addr: the PHY address
+ * @mmd: the PHY MMD to access (0 for clause 22 PHYs)
+ * @reg: the register to write
+ * @valp: value to write
+ *
+ * Issues a FW command through the given mailbox to write a PHY register.
+ */
+int t4_mdio_wr(struct adapter *adap, unsigned int mbox, unsigned int phy_addr,
+ unsigned int mmd, unsigned int reg, u16 val)
+{
+ struct fw_ldst_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_addrspace = htonl(FW_CMD_OP(FW_LDST_CMD) | FW_CMD_REQUEST |
+ FW_CMD_WRITE | FW_LDST_CMD_ADDRSPACE(FW_LDST_ADDRSPC_MDIO));
+ c.cycles_to_len16 = htonl(FW_LEN16(c));
+ c.u.mdio.paddr_mmd = htons(FW_LDST_CMD_PADDR(phy_addr) |
+ FW_LDST_CMD_MMD(mmd));
+ c.u.mdio.raddr = htons(reg);
+ c.u.mdio.rval = htons(val);
+
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_fw_hello - establish communication with FW
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @evt_mbox: mailbox to receive async FW events
+ * @master: specifies the caller's willingness to be the device master
+ * @state: returns the current device state
+ *
+ * Issues a command to establish communication with FW.
+ */
+int t4_fw_hello(struct adapter *adap, unsigned int mbox, unsigned int evt_mbox,
+ enum dev_master master, enum dev_state *state)
+{
+ int ret;
+ struct fw_hello_cmd c;
+
+ INIT_CMD(c, HELLO, WRITE);
+ c.err_to_mbasyncnot = htonl(
+ FW_HELLO_CMD_MASTERDIS(master == MASTER_CANT) |
+ FW_HELLO_CMD_MASTERFORCE(master == MASTER_MUST) |
+ FW_HELLO_CMD_MBMASTER(master == MASTER_MUST ? mbox : 0xff) |
+ FW_HELLO_CMD_MBASYNCNOT(evt_mbox));
+
+ ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c);
+ if (ret == 0 && state) {
+ u32 v = ntohl(c.err_to_mbasyncnot);
+ if (v & FW_HELLO_CMD_INIT)
+ *state = DEV_STATE_INIT;
+ else if (v & FW_HELLO_CMD_ERR)
+ *state = DEV_STATE_ERR;
+ else
+ *state = DEV_STATE_UNINIT;
+ }
+ return ret;
+}
+
+/**
+ * t4_fw_bye - end communication with FW
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ *
+ * Issues a command to terminate communication with FW.
+ */
+int t4_fw_bye(struct adapter *adap, unsigned int mbox)
+{
+ struct fw_bye_cmd c;
+
+ INIT_CMD(c, BYE, WRITE);
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_init_cmd - ask FW to initialize the device
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ *
+ * Issues a command to FW to partially initialize the device. This
+ * performs initialization that generally doesn't depend on user input.
+ */
+int t4_early_init(struct adapter *adap, unsigned int mbox)
+{
+ struct fw_initialize_cmd c;
+
+ INIT_CMD(c, INITIALIZE, WRITE);
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_fw_reset - issue a reset to FW
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @reset: specifies the type of reset to perform
+ *
+ * Issues a reset command of the specified type to FW.
+ */
+int t4_fw_reset(struct adapter *adap, unsigned int mbox, int reset)
+{
+ struct fw_reset_cmd c;
+
+ INIT_CMD(c, RESET, WRITE);
+ c.val = htonl(reset);
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_query_params - query FW or device parameters
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @nparams: the number of parameters
+ * @params: the parameter names
+ * @val: the parameter values
+ *
+ * Reads the value of FW or device parameters. Up to 7 parameters can be
+ * queried at once.
+ */
+int t4_query_params(struct adapter *adap, unsigned int mbox,
+ unsigned int nparams, const u32 *params, u32 *val)
+{
+ int i, ret;
+ struct fw_params_cmd c;
+ __be32 *p = &c.param[0].mnem;
+
+ if (nparams > 7)
+ return -EINVAL;
+
+ memset(&c, 0, sizeof(c));
+ INIT_CMD(c, PARAMS, READ);
+ for (i = 0; i < nparams; i++, p += 2)
+ *p = htonl(*params++);
+
+ ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c);
+ if (ret == 0)
+ for (i = 0, p = &c.param[0].val; i < nparams; i++, p += 2)
+ *val++ = ntohl(*p);
+ return ret;
+}
+
+/**
+ * t4_set_params - sets FW or device parameters
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @nparams: the number of parameters
+ * @params: the parameter names
+ * @val: the parameter values
+ *
+ * Sets the value of FW or device parameters. Up to 7 parameters can be
+ * specified at once.
+ */
+int t4_set_params(struct adapter *adap, unsigned int mbox, unsigned int nparams,
+ const u32 *params, const u32 *val)
+{
+ struct fw_params_cmd c;
+ __be32 *p = &c.param[0].mnem;
+
+ if (nparams > 7)
+ return -EINVAL;
+
+ memset(&c, 0, sizeof(c));
+ INIT_CMD(c, PARAMS, WRITE);
+ while (nparams--) {
+ *p++ = htonl(*params++);
+ *p++ = htonl(*val++);
+ }
+
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_cfg_pfvf - configure PF/VF resource limits
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @pf: the PF being configured
+ * @vf: the VF being configured
+ * @txq: the max number of egress queues
+ * @txq_eth_ctrl: the max number of egress Ethernet or control queues
+ * @rxqi: the max number of interrupt-capable ingress queues
+ * @rxq: the max number of interruptless ingress queues
+ * @tc: the PCI traffic class
+ * @vi: the max number of virtual interfaces
+ * @cmask: the channel access rights mask for the PF/VF
+ * @pmask: the port access rights mask for the PF/VF
+ * @nexact: the maximum number of exact MPS filters
+ * @rcaps: read capabilities
+ * @wxcaps: write/execute capabilities
+ *
+ * Configures resource limits and capabilities for a physical or virtual
+ * function.
+ */
+int t4_cfg_pfvf(struct adapter *adap, unsigned int mbox, unsigned int pf,
+ unsigned int vf, unsigned int txq, unsigned int txq_eth_ctrl,
+ unsigned int rxqi, unsigned int rxq, unsigned int tc,
+ unsigned int vi, unsigned int cmask, unsigned int pmask,
+ unsigned int nexact, unsigned int rcaps, unsigned int wxcaps)
+{
+ struct fw_pfvf_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_vfn = htonl(FW_CMD_OP(FW_PFVF_CMD) | FW_CMD_REQUEST |
+ FW_CMD_WRITE | FW_PFVF_CMD_PFN(pf) |
+ FW_PFVF_CMD_VFN(vf));
+ c.retval_len16 = htonl(FW_LEN16(c));
+ c.niqflint_niq = htonl(FW_PFVF_CMD_NIQFLINT(rxqi) |
+ FW_PFVF_CMD_NIQ(rxq));
+ c.cmask_to_neq = htonl(FW_PFVF_CMD_CMASK(cmask) |
+ FW_PFVF_CMD_PMASK(pmask) |
+ FW_PFVF_CMD_NEQ(txq));
+ c.tc_to_nexactf = htonl(FW_PFVF_CMD_TC(tc) | FW_PFVF_CMD_NVI(vi) |
+ FW_PFVF_CMD_NEXACTF(nexact));
+ c.r_caps_to_nethctrl = htonl(FW_PFVF_CMD_R_CAPS(rcaps) |
+ FW_PFVF_CMD_WX_CAPS(wxcaps) |
+ FW_PFVF_CMD_NETHCTRL(txq_eth_ctrl));
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_alloc_vi - allocate a virtual interface
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @port: physical port associated with the VI
+ * @pf: the PF owning the VI
+ * @vf: the VF owning the VI
+ * @nmac: number of MAC addresses needed (1 to 5)
+ * @mac: the MAC addresses of the VI
+ * @rss_size: size of RSS table slice associated with this VI
+ *
+ * Allocates a virtual interface for the given physical port. If @mac is
+ * not %NULL it contains the MAC addresses of the VI as assigned by FW.
+ * @mac should be large enough to hold @nmac Ethernet addresses, they are
+ * stored consecutively so the space needed is @nmac * 6 bytes.
+ * Returns a negative error number or the non-negative VI id.
+ */
+int t4_alloc_vi(struct adapter *adap, unsigned int mbox, unsigned int port,
+ unsigned int pf, unsigned int vf, unsigned int nmac, u8 *mac,
+ unsigned int *rss_size)
+{
+ int ret;
+ struct fw_vi_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_vfn = htonl(FW_CMD_OP(FW_VI_CMD) | FW_CMD_REQUEST |
+ FW_CMD_WRITE | FW_CMD_EXEC |
+ FW_VI_CMD_PFN(pf) | FW_VI_CMD_VFN(vf));
+ c.alloc_to_len16 = htonl(FW_VI_CMD_ALLOC | FW_LEN16(c));
+ c.portid_pkd = FW_VI_CMD_PORTID(port);
+ c.nmac = nmac - 1;
+
+ ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c);
+ if (ret)
+ return ret;
+
+ if (mac) {
+ memcpy(mac, c.mac, sizeof(c.mac));
+ switch (nmac) {
+ case 5:
+ memcpy(mac + 24, c.nmac3, sizeof(c.nmac3));
+ case 4:
+ memcpy(mac + 18, c.nmac2, sizeof(c.nmac2));
+ case 3:
+ memcpy(mac + 12, c.nmac1, sizeof(c.nmac1));
+ case 2:
+ memcpy(mac + 6, c.nmac0, sizeof(c.nmac0));
+ }
+ }
+ if (rss_size)
+ *rss_size = FW_VI_CMD_RSSSIZE_GET(ntohs(c.rsssize_pkd));
+ return ntohs(c.viid_pkd);
+}
+
+/**
+ * t4_free_vi - free a virtual interface
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @pf: the PF owning the VI
+ * @vf: the VF owning the VI
+ * @viid: virtual interface identifiler
+ *
+ * Free a previously allocated virtual interface.
+ */
+int t4_free_vi(struct adapter *adap, unsigned int mbox, unsigned int pf,
+ unsigned int vf, unsigned int viid)
+{
+ struct fw_vi_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_vfn = htonl(FW_CMD_OP(FW_VI_CMD) | FW_CMD_REQUEST |
+ FW_CMD_EXEC | FW_VI_CMD_PFN(pf) |
+ FW_VI_CMD_VFN(vf));
+ c.alloc_to_len16 = htonl(FW_VI_CMD_FREE | FW_LEN16(c));
+ c.viid_pkd = htons(FW_VI_CMD_VIID(viid));
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), &c);
+}
+
+/**
+ * t4_set_rxmode - set Rx properties of a virtual interface
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @viid: the VI id
+ * @mtu: the new MTU or -1
+ * @promisc: 1 to enable promiscuous mode, 0 to disable it, -1 no change
+ * @all_multi: 1 to enable all-multi mode, 0 to disable it, -1 no change
+ * @bcast: 1 to enable broadcast Rx, 0 to disable it, -1 no change
+ * @sleep_ok: if true we may sleep while awaiting command completion
+ *
+ * Sets Rx properties of a virtual interface.
+ */
+int t4_set_rxmode(struct adapter *adap, unsigned int mbox, unsigned int viid,
+ int mtu, int promisc, int all_multi, int bcast, bool sleep_ok)
+{
+ struct fw_vi_rxmode_cmd c;
+
+ /* convert to FW values */
+ if (mtu < 0)
+ mtu = FW_RXMODE_MTU_NO_CHG;
+ if (promisc < 0)
+ promisc = FW_VI_RXMODE_CMD_PROMISCEN_MASK;
+ if (all_multi < 0)
+ all_multi = FW_VI_RXMODE_CMD_ALLMULTIEN_MASK;
+ if (bcast < 0)
+ bcast = FW_VI_RXMODE_CMD_BROADCASTEN_MASK;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_viid = htonl(FW_CMD_OP(FW_VI_RXMODE_CMD) | FW_CMD_REQUEST |
+ FW_CMD_WRITE | FW_VI_RXMODE_CMD_VIID(viid));
+ c.retval_len16 = htonl(FW_LEN16(c));
+ c.mtu_to_broadcasten = htonl(FW_VI_RXMODE_CMD_MTU(mtu) |
+ FW_VI_RXMODE_CMD_PROMISCEN(promisc) |
+ FW_VI_RXMODE_CMD_ALLMULTIEN(all_multi) |
+ FW_VI_RXMODE_CMD_BROADCASTEN(bcast));
+ return t4_wr_mbox_meat(adap, mbox, &c, sizeof(c), NULL, sleep_ok);
+}
+
+/**
+ * t4_alloc_mac_filt - allocates exact-match filters for MAC addresses
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @viid: the VI id
+ * @free: if true any existing filters for this VI id are first removed
+ * @naddr: the number of MAC addresses to allocate filters for (up to 7)
+ * @addr: the MAC address(es)
+ * @idx: where to store the index of each allocated filter
+ * @hash: pointer to hash address filter bitmap
+ * @sleep_ok: call is allowed to sleep
+ *
+ * Allocates an exact-match filter for each of the supplied addresses and
+ * sets it to the corresponding address. If @idx is not %NULL it should
+ * have at least @naddr entries, each of which will be set to the index of
+ * the filter allocated for the corresponding MAC address. If a filter
+ * could not be allocated for an address its index is set to 0xffff.
+ * If @hash is not %NULL addresses that fail to allocate an exact filter
+ * are hashed and update the hash filter bitmap pointed at by @hash.
+ *
+ * Returns a negative error number or the number of filters allocated.
+ */
+int t4_alloc_mac_filt(struct adapter *adap, unsigned int mbox,
+ unsigned int viid, bool free, unsigned int naddr,
+ const u8 **addr, u16 *idx, u64 *hash, bool sleep_ok)
+{
+ int i, ret;
+ struct fw_vi_mac_cmd c;
+ struct fw_vi_mac_exact *p;
+
+ if (naddr > 7)
+ return -EINVAL;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_viid = htonl(FW_CMD_OP(FW_VI_MAC_CMD) | FW_CMD_REQUEST |
+ FW_CMD_WRITE | (free ? FW_CMD_EXEC : 0) |
+ FW_VI_MAC_CMD_VIID(viid));
+ c.freemacs_to_len16 = htonl(FW_VI_MAC_CMD_FREEMACS(free) |
+ FW_CMD_LEN16((naddr + 2) / 2));
+
+ for (i = 0, p = c.u.exact; i < naddr; i++, p++) {
+ p->valid_to_idx = htons(FW_VI_MAC_CMD_VALID |
+ FW_VI_MAC_CMD_IDX(FW_VI_MAC_ADD_MAC));
+ memcpy(p->macaddr, addr[i], sizeof(p->macaddr));
+ }
+
+ ret = t4_wr_mbox_meat(adap, mbox, &c, sizeof(c), &c, sleep_ok);
+ if (ret)
+ return ret;
+
+ for (i = 0, p = c.u.exact; i < naddr; i++, p++) {
+ u16 index = FW_VI_MAC_CMD_IDX_GET(ntohs(p->valid_to_idx));
+
+ if (idx)
+ idx[i] = index >= NEXACT_MAC ? 0xffff : index;
+ if (index < NEXACT_MAC)
+ ret++;
+ else if (hash)
+ *hash |= (1 << hash_mac_addr(addr[i]));
+ }
+ return ret;
+}
+
+/**
+ * t4_change_mac - modifies the exact-match filter for a MAC address
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @viid: the VI id
+ * @idx: index of existing filter for old value of MAC address, or -1
+ * @addr: the new MAC address value
+ * @persist: whether a new MAC allocation should be persistent
+ *
+ * Modifies an exact-match filter and sets it to the new MAC address.
+ * Note that in general it is not possible to modify the value of a given
+ * filter so the generic way to modify an address filter is to free the one
+ * being used by the old address value and allocate a new filter for the
+ * new address value. @idx can be -1 if the address is a new addition.
+ *
+ * Returns a negative error number or the index of the filter with the new
+ * MAC value.
+ */
+int t4_change_mac(struct adapter *adap, unsigned int mbox, unsigned int viid,
+ int idx, const u8 *addr, bool persist)
+{
+ int ret;
+ struct fw_vi_mac_cmd c;
+ struct fw_vi_mac_exact *p = c.u.exact;
+
+ if (idx < 0) /* new allocation */
+ idx = persist ? FW_VI_MAC_ADD_PERSIST_MAC : FW_VI_MAC_ADD_MAC;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_viid = htonl(FW_CMD_OP(FW_VI_MAC_CMD) | FW_CMD_REQUEST |
+ FW_CMD_WRITE | FW_VI_MAC_CMD_VIID(viid));
+ c.freemacs_to_len16 = htonl(FW_CMD_LEN16(1));
+ p->valid_to_idx = htons(FW_VI_MAC_CMD_VALID |
+ FW_VI_MAC_CMD_IDX(idx));
+ memcpy(p->macaddr, addr, sizeof(p->macaddr));
+
+ ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c);
+ if (ret == 0) {
+ ret = FW_VI_MAC_CMD_IDX_GET(ntohs(p->valid_to_idx));
+ if (ret >= NEXACT_MAC)
+ ret = -ENOMEM;
+ }
+ return ret;
+}
+
+/**
+ * t4_set_addr_hash - program the MAC inexact-match hash filter
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @viid: the VI id
+ * @ucast: whether the hash filter should also match unicast addresses
+ * @vec: the value to be written to the hash filter
+ * @sleep_ok: call is allowed to sleep
+ *
+ * Sets the 64-bit inexact-match hash filter for a virtual interface.
+ */
+int t4_set_addr_hash(struct adapter *adap, unsigned int mbox, unsigned int viid,
+ bool ucast, u64 vec, bool sleep_ok)
+{
+ struct fw_vi_mac_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_viid = htonl(FW_CMD_OP(FW_VI_MAC_CMD) | FW_CMD_REQUEST |
+ FW_CMD_WRITE | FW_VI_ENABLE_CMD_VIID(viid));
+ c.freemacs_to_len16 = htonl(FW_VI_MAC_CMD_HASHVECEN |
+ FW_VI_MAC_CMD_HASHUNIEN(ucast) |
+ FW_CMD_LEN16(1));
+ c.u.hash.hashvec = cpu_to_be64(vec);
+ return t4_wr_mbox_meat(adap, mbox, &c, sizeof(c), NULL, sleep_ok);
+}
+
+/**
+ * t4_enable_vi - enable/disable a virtual interface
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @viid: the VI id
+ * @rx_en: 1=enable Rx, 0=disable Rx
+ * @tx_en: 1=enable Tx, 0=disable Tx
+ *
+ * Enables/disables a virtual interface.
+ */
+int t4_enable_vi(struct adapter *adap, unsigned int mbox, unsigned int viid,
+ bool rx_en, bool tx_en)
+{
+ struct fw_vi_enable_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_viid = htonl(FW_CMD_OP(FW_VI_ENABLE_CMD) | FW_CMD_REQUEST |
+ FW_CMD_EXEC | FW_VI_ENABLE_CMD_VIID(viid));
+ c.ien_to_len16 = htonl(FW_VI_ENABLE_CMD_IEN(rx_en) |
+ FW_VI_ENABLE_CMD_EEN(tx_en) | FW_LEN16(c));
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_identify_port - identify a VI's port by blinking its LED
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @viid: the VI id
+ * @nblinks: how many times to blink LED at 2.5 Hz
+ *
+ * Identifies a VI's port by blinking its LED.
+ */
+int t4_identify_port(struct adapter *adap, unsigned int mbox, unsigned int viid,
+ unsigned int nblinks)
+{
+ struct fw_vi_enable_cmd c;
+
+ c.op_to_viid = htonl(FW_CMD_OP(FW_VI_ENABLE_CMD) | FW_CMD_REQUEST |
+ FW_CMD_EXEC | FW_VI_ENABLE_CMD_VIID(viid));
+ c.ien_to_len16 = htonl(FW_VI_ENABLE_CMD_LED | FW_LEN16(c));
+ c.blinkdur = htons(nblinks);
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_iq_start_stop - enable/disable an ingress queue and its FLs
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @start: %true to enable the queues, %false to disable them
+ * @pf: the PF owning the queues
+ * @vf: the VF owning the queues
+ * @iqid: ingress queue id
+ * @fl0id: FL0 queue id or 0xffff if no attached FL0
+ * @fl1id: FL1 queue id or 0xffff if no attached FL1
+ *
+ * Starts or stops an ingress queue and its associated FLs, if any.
+ */
+int t4_iq_start_stop(struct adapter *adap, unsigned int mbox, bool start,
+ unsigned int pf, unsigned int vf, unsigned int iqid,
+ unsigned int fl0id, unsigned int fl1id)
+{
+ struct fw_iq_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_vfn = htonl(FW_CMD_OP(FW_IQ_CMD) | FW_CMD_REQUEST |
+ FW_CMD_EXEC | FW_IQ_CMD_PFN(pf) |
+ FW_IQ_CMD_VFN(vf));
+ c.alloc_to_len16 = htonl(FW_IQ_CMD_IQSTART(start) |
+ FW_IQ_CMD_IQSTOP(!start) | FW_LEN16(c));
+ c.iqid = htons(iqid);
+ c.fl0id = htons(fl0id);
+ c.fl1id = htons(fl1id);
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_iq_free - free an ingress queue and its FLs
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @pf: the PF owning the queues
+ * @vf: the VF owning the queues
+ * @iqtype: the ingress queue type
+ * @iqid: ingress queue id
+ * @fl0id: FL0 queue id or 0xffff if no attached FL0
+ * @fl1id: FL1 queue id or 0xffff if no attached FL1
+ *
+ * Frees an ingress queue and its associated FLs, if any.
+ */
+int t4_iq_free(struct adapter *adap, unsigned int mbox, unsigned int pf,
+ unsigned int vf, unsigned int iqtype, unsigned int iqid,
+ unsigned int fl0id, unsigned int fl1id)
+{
+ struct fw_iq_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_vfn = htonl(FW_CMD_OP(FW_IQ_CMD) | FW_CMD_REQUEST |
+ FW_CMD_EXEC | FW_IQ_CMD_PFN(pf) |
+ FW_IQ_CMD_VFN(vf));
+ c.alloc_to_len16 = htonl(FW_IQ_CMD_FREE | FW_LEN16(c));
+ c.type_to_iqandstindex = htonl(FW_IQ_CMD_TYPE(iqtype));
+ c.iqid = htons(iqid);
+ c.fl0id = htons(fl0id);
+ c.fl1id = htons(fl1id);
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_eth_eq_free - free an Ethernet egress queue
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @pf: the PF owning the queue
+ * @vf: the VF owning the queue
+ * @eqid: egress queue id
+ *
+ * Frees an Ethernet egress queue.
+ */
+int t4_eth_eq_free(struct adapter *adap, unsigned int mbox, unsigned int pf,
+ unsigned int vf, unsigned int eqid)
+{
+ struct fw_eq_eth_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_vfn = htonl(FW_CMD_OP(FW_EQ_ETH_CMD) | FW_CMD_REQUEST |
+ FW_CMD_EXEC | FW_EQ_ETH_CMD_PFN(pf) |
+ FW_EQ_ETH_CMD_VFN(vf));
+ c.alloc_to_len16 = htonl(FW_EQ_ETH_CMD_FREE | FW_LEN16(c));
+ c.eqid_pkd = htonl(FW_EQ_ETH_CMD_EQID(eqid));
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_ctrl_eq_free - free a control egress queue
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @pf: the PF owning the queue
+ * @vf: the VF owning the queue
+ * @eqid: egress queue id
+ *
+ * Frees a control egress queue.
+ */
+int t4_ctrl_eq_free(struct adapter *adap, unsigned int mbox, unsigned int pf,
+ unsigned int vf, unsigned int eqid)
+{
+ struct fw_eq_ctrl_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_vfn = htonl(FW_CMD_OP(FW_EQ_CTRL_CMD) | FW_CMD_REQUEST |
+ FW_CMD_EXEC | FW_EQ_CTRL_CMD_PFN(pf) |
+ FW_EQ_CTRL_CMD_VFN(vf));
+ c.alloc_to_len16 = htonl(FW_EQ_CTRL_CMD_FREE | FW_LEN16(c));
+ c.cmpliqid_eqid = htonl(FW_EQ_CTRL_CMD_EQID(eqid));
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_ofld_eq_free - free an offload egress queue
+ * @adap: the adapter
+ * @mbox: mailbox to use for the FW command
+ * @pf: the PF owning the queue
+ * @vf: the VF owning the queue
+ * @eqid: egress queue id
+ *
+ * Frees a control egress queue.
+ */
+int t4_ofld_eq_free(struct adapter *adap, unsigned int mbox, unsigned int pf,
+ unsigned int vf, unsigned int eqid)
+{
+ struct fw_eq_ofld_cmd c;
+
+ memset(&c, 0, sizeof(c));
+ c.op_to_vfn = htonl(FW_CMD_OP(FW_EQ_OFLD_CMD) | FW_CMD_REQUEST |
+ FW_CMD_EXEC | FW_EQ_OFLD_CMD_PFN(pf) |
+ FW_EQ_OFLD_CMD_VFN(vf));
+ c.alloc_to_len16 = htonl(FW_EQ_OFLD_CMD_FREE | FW_LEN16(c));
+ c.eqid_pkd = htonl(FW_EQ_OFLD_CMD_EQID(eqid));
+ return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL);
+}
+
+/**
+ * t4_handle_fw_rpl - process a FW reply message
+ * @adap: the adapter
+ * @rpl: start of the FW message
+ *
+ * Processes a FW message, such as link state change messages.
+ */
+int t4_handle_fw_rpl(struct adapter *adap, const __be64 *rpl)
+{
+ u8 opcode = *(const u8 *)rpl;
+
+ if (opcode == FW_PORT_CMD) { /* link/module state change message */
+ int speed = 0, fc = 0;
+ const struct fw_port_cmd *p = (void *)rpl;
+ int chan = FW_PORT_CMD_PORTID_GET(ntohl(p->op_to_portid));
+ int port = adap->chan_map[chan];
+ struct port_info *pi = adap2pinfo(adap, port);
+ struct link_config *lc = &pi->link_cfg;
+ u32 stat = ntohl(p->u.info.lstatus_to_modtype);
+ int link_ok = (stat & FW_PORT_CMD_LSTATUS) != 0;
+ u32 mod = FW_PORT_CMD_MODTYPE_GET(stat);
+
+ if (stat & FW_PORT_CMD_RXPAUSE)
+ fc |= PAUSE_RX;
+ if (stat & FW_PORT_CMD_TXPAUSE)
+ fc |= PAUSE_TX;
+ if (stat & FW_PORT_CMD_LSPEED(FW_PORT_CAP_SPEED_100M))
+ speed = SPEED_100;
+ else if (stat & FW_PORT_CMD_LSPEED(FW_PORT_CAP_SPEED_1G))
+ speed = SPEED_1000;
+ else if (stat & FW_PORT_CMD_LSPEED(FW_PORT_CAP_SPEED_10G))
+ speed = SPEED_10000;
+
+ if (link_ok != lc->link_ok || speed != lc->speed ||
+ fc != lc->fc) { /* something changed */
+ lc->link_ok = link_ok;
+ lc->speed = speed;
+ lc->fc = fc;
+ t4_os_link_changed(adap, port, link_ok);
+ }
+ if (mod != pi->mod_type) {
+ pi->mod_type = mod;
+ t4_os_portmod_changed(adap, port);
+ }
+ }
+ return 0;
+}
+
+/**
+ * get_pci_mode - determine a card's PCI mode
+ * @adapter: the adapter
+ * @p: where to store the PCI settings
+ *
+ * Determines a card's PCI mode and associated parameters, such as speed
+ * and width.
+ */
+static void __devinit get_pci_mode(struct adapter *adapter,
+ struct pci_params *p)
+{
+ u16 val;
+ u32 pcie_cap;
+
+ pcie_cap = pci_find_capability(adapter->pdev, PCI_CAP_ID_EXP);
+ if (pcie_cap) {
+ pci_read_config_word(adapter->pdev, pcie_cap + PCI_EXP_LNKSTA,
+ &val);
+ p->speed = val & PCI_EXP_LNKSTA_CLS;
+ p->width = (val & PCI_EXP_LNKSTA_NLW) >> 4;
+ }
+}
+
+/**
+ * init_link_config - initialize a link's SW state
+ * @lc: structure holding the link state
+ * @caps: link capabilities
+ *
+ * Initializes the SW state maintained for each link, including the link's
+ * capabilities and default speed/flow-control/autonegotiation settings.
+ */
+static void __devinit init_link_config(struct link_config *lc,
+ unsigned int caps)
+{
+ lc->supported = caps;
+ lc->requested_speed = 0;
+ lc->speed = 0;
+ lc->requested_fc = lc->fc = PAUSE_RX | PAUSE_TX;
+ if (lc->supported & FW_PORT_CAP_ANEG) {
+ lc->advertising = lc->supported & ADVERT_MASK;
+ lc->autoneg = AUTONEG_ENABLE;
+ lc->requested_fc |= PAUSE_AUTONEG;
+ } else {
+ lc->advertising = 0;
+ lc->autoneg = AUTONEG_DISABLE;
+ }
+}
+
+static int __devinit wait_dev_ready(struct adapter *adap)
+{
+ if (t4_read_reg(adap, PL_WHOAMI) != 0xffffffff)
+ return 0;
+ msleep(500);
+ return t4_read_reg(adap, PL_WHOAMI) != 0xffffffff ? 0 : -EIO;
+}
+
+/**
+ * t4_prep_adapter - prepare SW and HW for operation
+ * @adapter: the adapter
+ * @reset: if true perform a HW reset
+ *
+ * Initialize adapter SW state for the various HW modules, set initial
+ * values for some adapter tunables, take PHYs out of reset, and
+ * initialize the MDIO interface.
+ */
+int __devinit t4_prep_adapter(struct adapter *adapter)
+{
+ int ret;
+
+ ret = wait_dev_ready(adapter);
+ if (ret < 0)
+ return ret;
+
+ get_pci_mode(adapter, &adapter->params.pci);
+ adapter->params.rev = t4_read_reg(adapter, PL_REV);
+
+ ret = get_vpd_params(adapter, &adapter->params.vpd);
+ if (ret < 0)
+ return ret;
+
+ init_cong_ctrl(adapter->params.a_wnd, adapter->params.b_wnd);
+
+ /*
+ * Default port for debugging in case we can't reach FW.
+ */
+ adapter->params.nports = 1;
+ adapter->params.portvec = 1;
+ return 0;
+}
+
+int __devinit t4_port_init(struct adapter *adap, int mbox, int pf, int vf)
+{
+ u8 addr[6];
+ int ret, i, j = 0;
+ struct fw_port_cmd c;
+
+ memset(&c, 0, sizeof(c));
+
+ for_each_port(adap, i) {
+ unsigned int rss_size;
+ struct port_info *p = adap2pinfo(adap, i);
+
+ while ((adap->params.portvec & (1 << j)) == 0)
+ j++;
+
+ c.op_to_portid = htonl(FW_CMD_OP(FW_PORT_CMD) |
+ FW_CMD_REQUEST | FW_CMD_READ |
+ FW_PORT_CMD_PORTID(j));
+ c.action_to_len16 = htonl(
+ FW_PORT_CMD_ACTION(FW_PORT_ACTION_GET_PORT_INFO) |
+ FW_LEN16(c));
+ ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c);
+ if (ret)
+ return ret;
+
+ ret = t4_alloc_vi(adap, mbox, j, pf, vf, 1, addr, &rss_size);
+ if (ret < 0)
+ return ret;
+
+ p->viid = ret;
+ p->tx_chan = j;
+ p->lport = j;
+ p->rss_size = rss_size;
+ memcpy(adap->port[i]->dev_addr, addr, ETH_ALEN);
+ memcpy(adap->port[i]->perm_addr, addr, ETH_ALEN);
+
+ ret = ntohl(c.u.info.lstatus_to_modtype);
+ p->mdio_addr = (ret & FW_PORT_CMD_MDIOCAP) ?
+ FW_PORT_CMD_MDIOADDR_GET(ret) : -1;
+ p->port_type = FW_PORT_CMD_PTYPE_GET(ret);
+ p->mod_type = FW_PORT_CMD_MODTYPE_GET(ret);
+
+ init_link_config(&p->link_cfg, ntohs(c.u.info.pcap));
+ j++;
+ }
+ return 0;
+}
new file mode 100644
@@ -0,0 +1,100 @@
+/*
+ * This file is part of the Chelsio T4 Ethernet driver for Linux.
+ *
+ * Copyright (c) 2003-2010 Chelsio Communications, Inc. All rights reserved.
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the
+ * OpenIB.org BSD license below:
+ *
+ * Redistribution and use in source and binary forms, with or
+ * without modification, are permitted provided that the following
+ * conditions are met:
+ *
+ * - Redistributions of source code must retain the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer.
+ *
+ * - Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials
+ * provided with the distribution.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
+ * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
+ * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+ * SOFTWARE.
+ */
+
+#ifndef __T4_HW_H
+#define __T4_HW_H
+
+#include <linux/types.h>
+
+enum {
+ NCHAN = 4, /* # of HW channels */
+ MAX_MTU = 9600, /* max MAC MTU, excluding header + FCS */
+ EEPROMSIZE = 17408, /* Serial EEPROM physical size */
+ EEPROMVSIZE = 32768, /* Serial EEPROM virtual address space size */
+ RSS_NENTRIES = 2048, /* # of entries in RSS mapping table */
+ TCB_SIZE = 128, /* TCB size */
+ NMTUS = 16, /* size of MTU table */
+ NCCTRL_WIN = 32, /* # of congestion control windows */
+ NEXACT_MAC = 336, /* # of exact MAC address filters */
+ L2T_SIZE = 4096, /* # of L2T entries */
+ MBOX_LEN = 64, /* mailbox size in bytes */
+ TRACE_LEN = 112, /* length of trace data and mask */
+ FILTER_OPT_LEN = 36, /* filter tuple width for optional components */
+ NWOL_PAT = 8, /* # of WoL patterns */
+ WOL_PAT_LEN = 128, /* length of WoL patterns */
+};
+
+enum {
+ SF_PAGE_SIZE = 256, /* serial flash page size */
+ SF_SEC_SIZE = 64 * 1024, /* serial flash sector size */
+ SF_SIZE = SF_SEC_SIZE * 16, /* serial flash size */
+};
+
+enum { RSP_TYPE_FLBUF, RSP_TYPE_CPL, RSP_TYPE_INTR }; /* response entry types */
+
+enum { MBOX_OWNER_NONE, MBOX_OWNER_FW, MBOX_OWNER_DRV }; /* mailbox owners */
+
+enum {
+ SGE_MAX_WR_LEN = 512, /* max WR size in bytes */
+ SGE_NTIMERS = 6, /* # of interrupt holdoff timer values */
+ SGE_NCOUNTERS = 4, /* # of interrupt packet counter values */
+};
+
+struct sge_qstat { /* data written to SGE queue status entries */
+ __be32 qid;
+ __be16 cidx;
+ __be16 pidx;
+};
+
+/*
+ * Structure for last 128 bits of response descriptors
+ */
+struct rsp_ctrl {
+ __be32 hdrbuflen_pidx;
+ __be32 pldbuflen_qid;
+ union {
+ u8 type_gen;
+ __be64 last_flit;
+ };
+};
+
+#define RSPD_NEWBUF 0x80000000U
+#define RSPD_LEN 0x7fffffffU
+
+#define RSPD_GEN(x) ((x) >> 7)
+#define RSPD_TYPE(x) (((x) >> 4) & 3)
+
+#define QINTR_CNT_EN 0x1
+#define QINTR_TIMER_IDX(x) ((x) << 1)
+#endif /* __T4_HW_H */
Signed-off-by: Dimitris Michailidis <dm@chelsio.com> --- drivers/net/cxgb4/t4_hw.c | 3119 +++++++++++++++++++++++++++++++++++++++++++++ drivers/net/cxgb4/t4_hw.h | 100 ++ 2 files changed, 3219 insertions(+), 0 deletions(-) create mode 100644 drivers/net/cxgb4/t4_hw.c create mode 100644 drivers/net/cxgb4/t4_hw.h