diff mbox

[v4,04/11] mtd: Add MPC5121 NAND Flash Controller driver

Message ID 4B83FA1C.8000902@marel.com
State New, archived
Headers show

Commit Message

Kári Davíðsson Feb. 23, 2010, 3:54 p.m. UTC 
Any special reason this in MPC5121 Revision 2 only?
I did not see anything that contradicted the rev 3 manual in the code.

But there is one harmless bug (since the NFC_CMD_FAIL symbol is never used), i.e.

git diff

The NAND chip is is detected (given that I disable the Revison check),
but the /dev7mtd0 is not accessable as block device. Is that normal?
The UBIFS also gives up I am assuming because the /dev/mtd0 is not block device.

rg
kd

On 02/16/2010 08:11 AM, Artem Bityutskiy wrote:
> On Mon, 2010-02-15 at 18:35 +0100, Anatolij Gustschin wrote:
>> Adds NAND Flash Controller driver for MPC5121 Revision 2.
>> All device features, except hardware ECC and power management,
>> are supported.
>>
>> Signed-off-by: Piotr Ziecik<kosmo@semihalf.com>
>> Signed-off-by: Wolfgang Denk<wd@denx.de>
>> Signed-off-by: Anatolij Gustschin<agust@denx.de>
>> Acked-by: Grant Likely<grant.likely@secretlab.ca>
>> Cc:<linux-mtd@lists.infradead.org>
>> Cc: Grant Likely<grant.likely@secretlab.ca>
>> Cc: John Rigby<jcrigby@gmail.com>
>> ---
>> Changes since v3:
>>   - include 'asm/mpc5121.h' header instead of 'asm/mpc5xxx.h'.
>>     This change is needed because arch patch adding reset
>>     module definition was reworked and doesn't add mpc5121
>>     specific definitions to common header for mpc52xx/mpc5121.
>>
>> Changes since v2:
>>   - move the arch bits into separate patch
>>     (it is the next patch in this series now)
>>   - use __devinit/__devexit/__devexit_p and __devinitdata
>>
>> Changes since v1:
>>   - add logfile with changes since previous version
>>
>> Changes since the patch version submitted in May 2009:
>>
>>   - move mpc5121_nfc.h to the driver .c as there is only one user
>>   - remove DRV_VERSION macro
>>   - replace printk() by dev_*()
>>   - drop unnecessary .suspend and .resume initializations
>>   - remove duplicate .name/.owner settings
>>   - fix mpc5121_nfc_init() to "return of_register_platform_driver(&mpc5121_nfc_driver);"
>>   - move module_init() to just below the init function
>>   - remove MODULE_VERSION
>>   - use "mtd: Add MPC5121 NAND Flash Controller driver" as the subject,
>>     previously it was "mpc5121: Added NAND Flash Controller driver.
>>
>>   drivers/mtd/nand/Kconfig       |    7 +
>>   drivers/mtd/nand/Makefile      |    1 +
>>   drivers/mtd/nand/mpc5121_nfc.c |  916 ++++++++++++++++++++++++++++++++++++++++
>>   3 files changed, 924 insertions(+), 0 deletions(-)
>>   create mode 100644 drivers/mtd/nand/mpc5121_nfc.c
>
> Pushed to my l2-mtd-2.6.git / dunno.
>
diff mbox

Patch

diff --git a/drivers/mtd/nand/mpc5121_nfc.c b/drivers/mtd/nand/mpc5121_nfc.c
index 191bf99..38a99ef 100644
--- a/drivers/mtd/nand/mpc5121_nfc.c
+++ b/drivers/mtd/nand/mpc5121_nfc.c
@@ -100,7 +100,7 @@ 
  #define NFC_OUTPUT             (1 << 3)
  #define NFC_ID                 (1 << 4)
  #define NFC_STATUS             (1 << 5)
-#define NFC_CMD_FAIL           (1 << 15)
+#define NFC_CMD_FAIL           (1 << 14)
  #define NFC_INT                        (1 << 15)

  /* Bit Definitions: NFC_WRPROT */