| Message ID | 1416487081-25467-1-git-send-email-Vincent.Yang@tw.fujitsu.com |
|---|---|
| State | Accepted, archived |
| Headers | show |
On Thu, Nov 20, 2014 at 6:38 AM, Vincent Yang <vincent.yang.fujitsu@gmail.com> wrote: > This patch adds new host controller driver for > Fujitsu SDHCI controller f_sdh30. > > Signed-off-by: Andy Green <andy.green@linaro.org> > Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com> > Signed-off-by: Tetsuya Takinishi <t.takinishi@jp.fujitsu.com> > --- > .../devicetree/bindings/mmc/sdhci-fujitsu.txt | 35 +++ > drivers/mmc/host/Kconfig | 9 + > drivers/mmc/host/Makefile | 1 + > drivers/mmc/host/sdhci_f_sdh30.c | 319 +++++++++++++++++++++ > 4 files changed, 364 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt > create mode 100644 drivers/mmc/host/sdhci_f_sdh30.c > > diff --git a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt > new file mode 100644 > index 0000000..a1e0b64 > --- /dev/null > +++ b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt > @@ -0,0 +1,35 @@ > +* Fujitsu SDHCI controller > + > +This file documents differences between the core properties in mmc.txt > +and the properties used by the sdhci_f_sdh30 driver. > + > +Required properties: > +- compatible: "fujitsu,mb86s70-sdh30" It would be nice to have sdhci in the name to indicate it is an SDHCI controller. > +- voltage-ranges : This is a list of pairs. In each pair, two cells > + are required. First cell specifies minimum slot voltage (mV), second > + cell specifies maximum slot voltage (mV). In case of supported voltage > + range is discontinuous, several ranges could be specified as a list. > + > +Optional properties: > +- vqmmc-supply: phandle to the regulator device tree node, mentioned > + as the VCCQ/VDD_IO supply in the eMMC/SD specs. > +- clocks: Must contain an entry for each entry in clock-names. It is a > + list of phandles and clock-specifier pairs. > + See ../clocks/clock-bindings.txt for details. > +- clock-names: Should contain the following two entries: > + "iface" - clock used for sdhci interface > + "core" - core clock for sdhci controller > + > +Example: > + > + sdhci1: sdio@36600000 { > + compatible = "fujitsu,mb86s70-sdh30"; > + reg = <0 0x36600000 0x1000>; > + interrupts = <0 172 0x4>, > + <0 173 0x4>; > + voltage-ranges = <1800 1800>, <3300 3300>; > + bus-width = <4>; > + vqmmc-supply = <&vccq_sdhci1>; > + clocks = <&clk_hdmi_2_0>, <&clk_hdmi_3_0>; > + clock-names = "iface", "core"; > + }; > diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig > index 1386065..cbe5e3c 100644 > --- a/drivers/mmc/host/Kconfig > +++ b/drivers/mmc/host/Kconfig > @@ -290,6 +290,15 @@ config MMC_SDHCI_BCM2835 > This selects the BCM2835 SD/MMC controller. If you have a BCM2835 > platform with SD or MMC devices, say Y or M here. > > +config MMC_SDHCI_F_SDH30 > + tristate "SDHCI support for Fujitsu Semiconductor F_SDH30" > + depends on ARCH_MB86S7X > + depends on MMC_SDHCI_PLTFM > + depends on OF > + help > + This selects the Secure Digital Host Controller Interface (SDHCI) > + Needed by some Fujitsu SoC for MMC / SD / SDIO support. > + If you have a controller with this interface, say Y or M here. > If unsure, say N. > > config MMC_MOXART > diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile > index b09ecfb..63efc38 100644 > --- a/drivers/mmc/host/Makefile > +++ b/drivers/mmc/host/Makefile > @@ -16,6 +16,7 @@ obj-$(CONFIG_MMC_SDHCI_PXAV3) += sdhci-pxav3.o > obj-$(CONFIG_MMC_SDHCI_PXAV2) += sdhci-pxav2.o > obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c.o > obj-$(CONFIG_MMC_SDHCI_SIRF) += sdhci-sirf.o > +obj-$(CONFIG_MMC_SDHCI_F_SDH30) += sdhci_f_sdh30.o > obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o > obj-$(CONFIG_MMC_WBSD) += wbsd.o > obj-$(CONFIG_MMC_AU1X) += au1xmmc.o > diff --git a/drivers/mmc/host/sdhci_f_sdh30.c b/drivers/mmc/host/sdhci_f_sdh30.c > new file mode 100644 > index 0000000..f6eba5a > --- /dev/null > +++ b/drivers/mmc/host/sdhci_f_sdh30.c > @@ -0,0 +1,319 @@ > +/* > + * linux/drivers/mmc/host/sdhci_f_sdh30.c > + * > + * Copyright (C) 2013 - 2014 Fujitsu Semiconductor, Ltd > + * Vincent Yang <vincent.yang@tw.fujitsu.com> > + * Copyright (C) 2014 Linaro Ltd Andy Green <andy.green@linaro.org> > + * > + * This program is free software: you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation, version 2 of the License. > + */ > + > +#include <linux/err.h> > +#include <linux/delay.h> > +#include <linux/module.h> > +#include <linux/mmc/sd.h> > +#include <linux/mmc/host.h> > +#include <linux/mmc/card.h> > +#include <linux/gpio.h> > +#include <linux/of_gpio.h> > +#include <linux/of_address.h> > +#include <linux/platform_device.h> > +#include <linux/pm.h> > +#include <linux/pm_runtime.h> > +#include <linux/suspend.h> > + > +#include "sdhci.h" > +#include "sdhci-pltfm.h" > + > +/* F_SDH30 extended Controller registers */ > +#define F_SDH30_AHB_CONFIG 0x100 > +#define F_SDH30_AHB_BIGED 0x00000040 > +#define F_SDH30_BUSLOCK_DMA 0x00000020 > +#define F_SDH30_BUSLOCK_EN 0x00000010 > +#define F_SDH30_SIN 0x00000008 > +#define F_SDH30_AHB_INCR_16 0x00000004 > +#define F_SDH30_AHB_INCR_8 0x00000002 > +#define F_SDH30_AHB_INCR_4 0x00000001 > + > +#define F_SDH30_TUNING_SETTING 0x108 > +#define F_SDH30_CMD_CHK_DIS 0x00010000 > + > +#define F_SDH30_IO_CONTROL2 0x114 > +#define F_SDH30_CRES_O_DN 0x00080000 > +#define F_SDH30_MSEL_O_1_8 0x00040000 > + > +#define F_SDH30_ESD_CONTROL 0x124 > +#define F_SDH30_EMMC_RST 0x00000002 > +#define F_SDH30_EMMC_HS200 0x01000000 > + > +#define F_SDH30_CMD_DAT_DELAY 0x200 > + > +#define F_SDH30_MIN_CLOCK 400000 > + > +struct f_sdhost_priv { > + struct clk *clk_iface; > + struct clk *clk; > + u32 vendor_hs200; > + struct device *dev; > +}; > + > +void sdhci_f_sdh30_soft_voltage_switch(struct sdhci_host *host) > +{ > + struct f_sdhost_priv *priv = sdhci_priv(host); > + u32 ctrl = 0; > + > + usleep_range(2500, 3000); > + ctrl = sdhci_readl(host, F_SDH30_IO_CONTROL2); > + ctrl |= F_SDH30_CRES_O_DN; > + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2); > + ctrl |= F_SDH30_MSEL_O_1_8; > + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2); > + > + ctrl &= ~F_SDH30_CRES_O_DN; > + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2); > + usleep_range(2500, 3000); > + > + if (priv->vendor_hs200) { > + dev_info(priv->dev, "%s: setting hs200\n", __func__); > + ctrl = sdhci_readl(host, F_SDH30_ESD_CONTROL); > + ctrl |= priv->vendor_hs200; > + sdhci_writel(host, ctrl, F_SDH30_ESD_CONTROL); > + } > + > + ctrl = sdhci_readl(host, F_SDH30_TUNING_SETTING); > + ctrl |= F_SDH30_CMD_CHK_DIS; > + sdhci_writel(host, ctrl, F_SDH30_TUNING_SETTING); > +} > + > +unsigned int sdhci_f_sdh30_get_min_clock(struct sdhci_host *host) > +{ > + return F_SDH30_MIN_CLOCK; > +} > + > +void sdhci_f_sdh30_reset(struct sdhci_host *host, u8 mask) > +{ > + if (sdhci_readw(host, SDHCI_CLOCK_CONTROL) == 0) > + sdhci_writew(host, 0xBC01, SDHCI_CLOCK_CONTROL); > + > + sdhci_reset(host, mask); > +} > + > +static const struct sdhci_ops sdhci_f_sdh30_ops = { > + .voltage_switch = sdhci_f_sdh30_soft_voltage_switch, > + .get_min_clock = sdhci_f_sdh30_get_min_clock, > + .reset = sdhci_f_sdh30_reset, > + .set_clock = sdhci_set_clock, > + .set_bus_width = sdhci_set_bus_width, > + .set_uhs_signaling = sdhci_set_uhs_signaling, > +}; > + > +static int sdhci_f_sdh30_probe(struct platform_device *pdev) > +{ > + struct sdhci_host *host; > + struct device *dev = &pdev->dev; > + int irq, ctrl = 0, ret = 0; > + struct f_sdhost_priv *priv; > + u32 reg = 0; > + > + irq = platform_get_irq(pdev, 0); > + if (irq < 0) { > + dev_err(dev, "%s: no irq specified\n", __func__); > + ret = irq; > + goto err; > + } > + > + host = sdhci_alloc_host(dev, sizeof(struct sdhci_host) + > + sizeof(struct f_sdhost_priv)); > + if (IS_ERR(host)) { > + dev_err(dev, "%s: host allocate error\n", __func__); > + ret = -ENOMEM; > + goto err; > + } > + priv = sdhci_priv(host); > + priv->dev = dev; > + > + host->quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC | > + SDHCI_QUIRK_INVERTED_WRITE_PROTECT; > + host->quirks2 = SDHCI_QUIRK2_SUPPORT_SINGLE | > + SDHCI_QUIRK2_TUNING_WORK_AROUND; > + > + ret = mmc_of_parse(host->mmc); > + if (ret) > + goto err_of_parse; > + > + ret = mmc_of_parse_voltage(pdev->dev.of_node, &host->ocr_mask); > + if (ret) > + goto err_of_parse; > + > + platform_set_drvdata(pdev, host); > + > + sdhci_get_of_property(pdev); > + host->hw_name = "f_sdh30"; > + host->ops = &sdhci_f_sdh30_ops; > + host->irq = irq; > + > + host->ioaddr = of_iomap(pdev->dev.of_node, 0); > + if (!host->ioaddr) { > + dev_err(dev, "%s: failed to remap registers\n", __func__); > + ret = -ENXIO; > + goto err_remap; > + } > + > + priv->clk_iface = clk_get(&pdev->dev, "iface"); > + if (!IS_ERR(priv->clk_iface)) { > + ret = clk_prepare_enable(priv->clk_iface); > + if (ret < 0) { > + dev_err(dev, "Failed to enable iface clock: %d\n", ret); > + goto err_clk1; > + } > + } > + priv->clk = clk_get(&pdev->dev, "core"); > + if (!IS_ERR(priv->clk)) { > + ret = clk_prepare_enable(priv->clk); > + if (ret < 0) { > + dev_err(dev, "Failed to enable core clock: %d\n", ret); > + goto err_clk2; > + } > + } > + > +#ifdef CONFIG_PM_RUNTIME > + pm_runtime_set_active(&pdev->dev); > + pm_runtime_enable(&pdev->dev); > + ret = pm_runtime_get_sync(&pdev->dev); > + if (ret < 0) > + dev_err(dev, "Failed to pm_runtime_get_sync: %d\n", ret); > +#endif > + > + ret = sdhci_add_host(host); > + if (ret) { > + dev_err(dev, "%s: host add error\n", __func__); > + goto err_add_host; > + } > + > + /* init vendor specific regs */ > + ctrl = sdhci_readw(host, F_SDH30_AHB_CONFIG); > + ctrl |= F_SDH30_SIN | F_SDH30_AHB_INCR_16 | F_SDH30_AHB_INCR_8 | > + F_SDH30_AHB_INCR_4; > + ctrl &= ~(F_SDH30_AHB_BIGED | F_SDH30_BUSLOCK_EN); > + sdhci_writew(host, ctrl, F_SDH30_AHB_CONFIG); > + > + reg = sdhci_readl(host, F_SDH30_ESD_CONTROL); > + sdhci_writel(host, reg & ~F_SDH30_EMMC_RST, F_SDH30_ESD_CONTROL); > + msleep(20); > + sdhci_writel(host, reg | F_SDH30_EMMC_RST, F_SDH30_ESD_CONTROL); > + > + reg = sdhci_readl(host, SDHCI_CAPABILITIES); > + if (reg & SDHCI_CAN_DO_8BIT) > + priv->vendor_hs200 = F_SDH30_EMMC_HS200; > + else > + priv->vendor_hs200 = 0; > + > + return 0; > + > +err_add_host: > + clk_put(priv->clk); > +err_clk2: > + clk_put(priv->clk_iface); > +err_clk1: > + iounmap(host->ioaddr); > +err_remap: > +err_of_parse: > + sdhci_free_host(host); > +err: > + return ret; > +} > + > +static int sdhci_f_sdh30_remove(struct platform_device *pdev) > +{ > + struct sdhci_host *host = platform_get_drvdata(pdev); > + struct f_sdhost_priv *priv = sdhci_priv(host); > + struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + > + sdhci_remove_host(host, readl(host->ioaddr + SDHCI_INT_STATUS) == > + 0xffffffff); > + iounmap(host->ioaddr); > + release_mem_region(iomem->start, resource_size(iomem)); > + > + clk_disable_unprepare(priv->clk_iface); > + clk_disable_unprepare(priv->clk); > + > + clk_put(priv->clk); > + clk_put(priv->clk_iface); > + > + sdhci_free_host(host); > + platform_set_drvdata(pdev, NULL); > + > + return 0; > +} > + > +#ifdef CONFIG_PM_SLEEP > +static int sdhci_f_sdh30_suspend(struct device *dev) > +{ > + struct sdhci_host *host = dev_get_drvdata(dev); > + > + return sdhci_suspend_host(host); > +} > + > +static int sdhci_f_sdh30_resume(struct device *dev) > +{ > + struct sdhci_host *host = dev_get_drvdata(dev); > + > + return sdhci_resume_host(host); > +} > +#endif > + > +#ifdef CONFIG_PM_RUNTIME > +static int sdhci_f_sdh30_runtime_suspend(struct device *dev) > +{ > + struct sdhci_host *host = dev_get_drvdata(dev); > + > + return sdhci_runtime_suspend_host(host); > +} > + > +static int sdhci_f_sdh30_runtime_resume(struct device *dev) > +{ > + struct sdhci_host *host = dev_get_drvdata(dev); > + > + return sdhci_runtime_resume_host(host); > +} > +#endif > + > +#ifdef CONFIG_PM > +static const struct dev_pm_ops sdhci_f_sdh30_pmops = { > + SET_SYSTEM_SLEEP_PM_OPS(sdhci_f_sdh30_suspend, sdhci_f_sdh30_resume) > + SET_RUNTIME_PM_OPS(sdhci_f_sdh30_runtime_suspend, > + sdhci_f_sdh30_runtime_resume, NULL) > +}; > + > +#define SDHCI_F_SDH30_PMOPS (&sdhci_f_sdh30_pmops) > + > +#else > +#define SDHCI_F_SDH30_PMOPS NULL > +#endif > + > +static const struct of_device_id f_sdh30_dt_ids[] = { > + { .compatible = "fujitsu,mb86s70-sdh30" }, > + { /* sentinel */ } > +}; > +MODULE_DEVICE_TABLE(of, f_sdh30_dt_ids); > + > +static struct platform_driver sdhci_f_sdh30_driver = { > + .driver = { > + .name = "f_sdh30", > + .of_match_table = f_sdh30_dt_ids, > +#ifdef CONFIG_PM_SLEEP > + .pm = SDHCI_F_SDH30_PMOPS, > +#endif > + }, > + .probe = sdhci_f_sdh30_probe, > + .remove = sdhci_f_sdh30_remove, > +}; > + > +module_platform_driver(sdhci_f_sdh30_driver); > + > +MODULE_DESCRIPTION("F_SDH30 SD Card Controller driver"); > +MODULE_LICENSE("GPL v2"); > +MODULE_AUTHOR("FUJITSU SEMICONDUCTOR LTD."); > +MODULE_ALIAS("platform:f_sdh30"); > -- > 1.9.0 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
2014-11-20 23:22 GMT+08:00 Rob Herring <robherring2@gmail.com>: > On Thu, Nov 20, 2014 at 6:38 AM, Vincent Yang > <vincent.yang.fujitsu@gmail.com> wrote: >> This patch adds new host controller driver for >> Fujitsu SDHCI controller f_sdh30. >> >> Signed-off-by: Andy Green <andy.green@linaro.org> >> Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com> >> Signed-off-by: Tetsuya Takinishi <t.takinishi@jp.fujitsu.com> >> --- >> .../devicetree/bindings/mmc/sdhci-fujitsu.txt | 35 +++ >> drivers/mmc/host/Kconfig | 9 + >> drivers/mmc/host/Makefile | 1 + >> drivers/mmc/host/sdhci_f_sdh30.c | 319 +++++++++++++++++++++ >> 4 files changed, 364 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt >> create mode 100644 drivers/mmc/host/sdhci_f_sdh30.c >> >> diff --git a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt >> new file mode 100644 >> index 0000000..a1e0b64 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt >> @@ -0,0 +1,35 @@ >> +* Fujitsu SDHCI controller >> + >> +This file documents differences between the core properties in mmc.txt >> +and the properties used by the sdhci_f_sdh30 driver. >> + >> +Required properties: >> +- compatible: "fujitsu,mb86s70-sdh30" > > It would be nice to have sdhci in the name to indicate it is an SDHCI > controller. Yes, we will update it to "fujitsu,sdhci-f-sdh30" Thanks for your review! - Vincent Yang > >> +- voltage-ranges : This is a list of pairs. In each pair, two cells >> + are required. First cell specifies minimum slot voltage (mV), second >> + cell specifies maximum slot voltage (mV). In case of supported voltage >> + range is discontinuous, several ranges could be specified as a list. >> + >> +Optional properties: >> +- vqmmc-supply: phandle to the regulator device tree node, mentioned >> + as the VCCQ/VDD_IO supply in the eMMC/SD specs. >> +- clocks: Must contain an entry for each entry in clock-names. It is a >> + list of phandles and clock-specifier pairs. >> + See ../clocks/clock-bindings.txt for details. >> +- clock-names: Should contain the following two entries: >> + "iface" - clock used for sdhci interface >> + "core" - core clock for sdhci controller >> + >> +Example: >> + >> + sdhci1: sdio@36600000 { >> + compatible = "fujitsu,mb86s70-sdh30"; >> + reg = <0 0x36600000 0x1000>; >> + interrupts = <0 172 0x4>, >> + <0 173 0x4>; >> + voltage-ranges = <1800 1800>, <3300 3300>; >> + bus-width = <4>; >> + vqmmc-supply = <&vccq_sdhci1>; >> + clocks = <&clk_hdmi_2_0>, <&clk_hdmi_3_0>; >> + clock-names = "iface", "core"; >> + }; >> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig >> index 1386065..cbe5e3c 100644 >> --- a/drivers/mmc/host/Kconfig >> +++ b/drivers/mmc/host/Kconfig >> @@ -290,6 +290,15 @@ config MMC_SDHCI_BCM2835 >> This selects the BCM2835 SD/MMC controller. If you have a BCM2835 >> platform with SD or MMC devices, say Y or M here. >> >> +config MMC_SDHCI_F_SDH30 >> + tristate "SDHCI support for Fujitsu Semiconductor F_SDH30" >> + depends on ARCH_MB86S7X >> + depends on MMC_SDHCI_PLTFM >> + depends on OF >> + help >> + This selects the Secure Digital Host Controller Interface (SDHCI) >> + Needed by some Fujitsu SoC for MMC / SD / SDIO support. >> + If you have a controller with this interface, say Y or M here. >> If unsure, say N. >> >> config MMC_MOXART >> diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile >> index b09ecfb..63efc38 100644 >> --- a/drivers/mmc/host/Makefile >> +++ b/drivers/mmc/host/Makefile >> @@ -16,6 +16,7 @@ obj-$(CONFIG_MMC_SDHCI_PXAV3) += sdhci-pxav3.o >> obj-$(CONFIG_MMC_SDHCI_PXAV2) += sdhci-pxav2.o >> obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c.o >> obj-$(CONFIG_MMC_SDHCI_SIRF) += sdhci-sirf.o >> +obj-$(CONFIG_MMC_SDHCI_F_SDH30) += sdhci_f_sdh30.o >> obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o >> obj-$(CONFIG_MMC_WBSD) += wbsd.o >> obj-$(CONFIG_MMC_AU1X) += au1xmmc.o >> diff --git a/drivers/mmc/host/sdhci_f_sdh30.c b/drivers/mmc/host/sdhci_f_sdh30.c >> new file mode 100644 >> index 0000000..f6eba5a >> --- /dev/null >> +++ b/drivers/mmc/host/sdhci_f_sdh30.c >> @@ -0,0 +1,319 @@ >> +/* >> + * linux/drivers/mmc/host/sdhci_f_sdh30.c >> + * >> + * Copyright (C) 2013 - 2014 Fujitsu Semiconductor, Ltd >> + * Vincent Yang <vincent.yang@tw.fujitsu.com> >> + * Copyright (C) 2014 Linaro Ltd Andy Green <andy.green@linaro.org> >> + * >> + * This program is free software: you can redistribute it and/or modify >> + * it under the terms of the GNU General Public License as published by >> + * the Free Software Foundation, version 2 of the License. >> + */ >> + >> +#include <linux/err.h> >> +#include <linux/delay.h> >> +#include <linux/module.h> >> +#include <linux/mmc/sd.h> >> +#include <linux/mmc/host.h> >> +#include <linux/mmc/card.h> >> +#include <linux/gpio.h> >> +#include <linux/of_gpio.h> >> +#include <linux/of_address.h> >> +#include <linux/platform_device.h> >> +#include <linux/pm.h> >> +#include <linux/pm_runtime.h> >> +#include <linux/suspend.h> >> + >> +#include "sdhci.h" >> +#include "sdhci-pltfm.h" >> + >> +/* F_SDH30 extended Controller registers */ >> +#define F_SDH30_AHB_CONFIG 0x100 >> +#define F_SDH30_AHB_BIGED 0x00000040 >> +#define F_SDH30_BUSLOCK_DMA 0x00000020 >> +#define F_SDH30_BUSLOCK_EN 0x00000010 >> +#define F_SDH30_SIN 0x00000008 >> +#define F_SDH30_AHB_INCR_16 0x00000004 >> +#define F_SDH30_AHB_INCR_8 0x00000002 >> +#define F_SDH30_AHB_INCR_4 0x00000001 >> + >> +#define F_SDH30_TUNING_SETTING 0x108 >> +#define F_SDH30_CMD_CHK_DIS 0x00010000 >> + >> +#define F_SDH30_IO_CONTROL2 0x114 >> +#define F_SDH30_CRES_O_DN 0x00080000 >> +#define F_SDH30_MSEL_O_1_8 0x00040000 >> + >> +#define F_SDH30_ESD_CONTROL 0x124 >> +#define F_SDH30_EMMC_RST 0x00000002 >> +#define F_SDH30_EMMC_HS200 0x01000000 >> + >> +#define F_SDH30_CMD_DAT_DELAY 0x200 >> + >> +#define F_SDH30_MIN_CLOCK 400000 >> + >> +struct f_sdhost_priv { >> + struct clk *clk_iface; >> + struct clk *clk; >> + u32 vendor_hs200; >> + struct device *dev; >> +}; >> + >> +void sdhci_f_sdh30_soft_voltage_switch(struct sdhci_host *host) >> +{ >> + struct f_sdhost_priv *priv = sdhci_priv(host); >> + u32 ctrl = 0; >> + >> + usleep_range(2500, 3000); >> + ctrl = sdhci_readl(host, F_SDH30_IO_CONTROL2); >> + ctrl |= F_SDH30_CRES_O_DN; >> + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2); >> + ctrl |= F_SDH30_MSEL_O_1_8; >> + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2); >> + >> + ctrl &= ~F_SDH30_CRES_O_DN; >> + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2); >> + usleep_range(2500, 3000); >> + >> + if (priv->vendor_hs200) { >> + dev_info(priv->dev, "%s: setting hs200\n", __func__); >> + ctrl = sdhci_readl(host, F_SDH30_ESD_CONTROL); >> + ctrl |= priv->vendor_hs200; >> + sdhci_writel(host, ctrl, F_SDH30_ESD_CONTROL); >> + } >> + >> + ctrl = sdhci_readl(host, F_SDH30_TUNING_SETTING); >> + ctrl |= F_SDH30_CMD_CHK_DIS; >> + sdhci_writel(host, ctrl, F_SDH30_TUNING_SETTING); >> +} >> + >> +unsigned int sdhci_f_sdh30_get_min_clock(struct sdhci_host *host) >> +{ >> + return F_SDH30_MIN_CLOCK; >> +} >> + >> +void sdhci_f_sdh30_reset(struct sdhci_host *host, u8 mask) >> +{ >> + if (sdhci_readw(host, SDHCI_CLOCK_CONTROL) == 0) >> + sdhci_writew(host, 0xBC01, SDHCI_CLOCK_CONTROL); >> + >> + sdhci_reset(host, mask); >> +} >> + >> +static const struct sdhci_ops sdhci_f_sdh30_ops = { >> + .voltage_switch = sdhci_f_sdh30_soft_voltage_switch, >> + .get_min_clock = sdhci_f_sdh30_get_min_clock, >> + .reset = sdhci_f_sdh30_reset, >> + .set_clock = sdhci_set_clock, >> + .set_bus_width = sdhci_set_bus_width, >> + .set_uhs_signaling = sdhci_set_uhs_signaling, >> +}; >> + >> +static int sdhci_f_sdh30_probe(struct platform_device *pdev) >> +{ >> + struct sdhci_host *host; >> + struct device *dev = &pdev->dev; >> + int irq, ctrl = 0, ret = 0; >> + struct f_sdhost_priv *priv; >> + u32 reg = 0; >> + >> + irq = platform_get_irq(pdev, 0); >> + if (irq < 0) { >> + dev_err(dev, "%s: no irq specified\n", __func__); >> + ret = irq; >> + goto err; >> + } >> + >> + host = sdhci_alloc_host(dev, sizeof(struct sdhci_host) + >> + sizeof(struct f_sdhost_priv)); >> + if (IS_ERR(host)) { >> + dev_err(dev, "%s: host allocate error\n", __func__); >> + ret = -ENOMEM; >> + goto err; >> + } >> + priv = sdhci_priv(host); >> + priv->dev = dev; >> + >> + host->quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC | >> + SDHCI_QUIRK_INVERTED_WRITE_PROTECT; >> + host->quirks2 = SDHCI_QUIRK2_SUPPORT_SINGLE | >> + SDHCI_QUIRK2_TUNING_WORK_AROUND; >> + >> + ret = mmc_of_parse(host->mmc); >> + if (ret) >> + goto err_of_parse; >> + >> + ret = mmc_of_parse_voltage(pdev->dev.of_node, &host->ocr_mask); >> + if (ret) >> + goto err_of_parse; >> + >> + platform_set_drvdata(pdev, host); >> + >> + sdhci_get_of_property(pdev); >> + host->hw_name = "f_sdh30"; >> + host->ops = &sdhci_f_sdh30_ops; >> + host->irq = irq; >> + >> + host->ioaddr = of_iomap(pdev->dev.of_node, 0); >> + if (!host->ioaddr) { >> + dev_err(dev, "%s: failed to remap registers\n", __func__); >> + ret = -ENXIO; >> + goto err_remap; >> + } >> + >> + priv->clk_iface = clk_get(&pdev->dev, "iface"); >> + if (!IS_ERR(priv->clk_iface)) { >> + ret = clk_prepare_enable(priv->clk_iface); >> + if (ret < 0) { >> + dev_err(dev, "Failed to enable iface clock: %d\n", ret); >> + goto err_clk1; >> + } >> + } >> + priv->clk = clk_get(&pdev->dev, "core"); >> + if (!IS_ERR(priv->clk)) { >> + ret = clk_prepare_enable(priv->clk); >> + if (ret < 0) { >> + dev_err(dev, "Failed to enable core clock: %d\n", ret); >> + goto err_clk2; >> + } >> + } >> + >> +#ifdef CONFIG_PM_RUNTIME >> + pm_runtime_set_active(&pdev->dev); >> + pm_runtime_enable(&pdev->dev); >> + ret = pm_runtime_get_sync(&pdev->dev); >> + if (ret < 0) >> + dev_err(dev, "Failed to pm_runtime_get_sync: %d\n", ret); >> +#endif >> + >> + ret = sdhci_add_host(host); >> + if (ret) { >> + dev_err(dev, "%s: host add error\n", __func__); >> + goto err_add_host; >> + } >> + >> + /* init vendor specific regs */ >> + ctrl = sdhci_readw(host, F_SDH30_AHB_CONFIG); >> + ctrl |= F_SDH30_SIN | F_SDH30_AHB_INCR_16 | F_SDH30_AHB_INCR_8 | >> + F_SDH30_AHB_INCR_4; >> + ctrl &= ~(F_SDH30_AHB_BIGED | F_SDH30_BUSLOCK_EN); >> + sdhci_writew(host, ctrl, F_SDH30_AHB_CONFIG); >> + >> + reg = sdhci_readl(host, F_SDH30_ESD_CONTROL); >> + sdhci_writel(host, reg & ~F_SDH30_EMMC_RST, F_SDH30_ESD_CONTROL); >> + msleep(20); >> + sdhci_writel(host, reg | F_SDH30_EMMC_RST, F_SDH30_ESD_CONTROL); >> + >> + reg = sdhci_readl(host, SDHCI_CAPABILITIES); >> + if (reg & SDHCI_CAN_DO_8BIT) >> + priv->vendor_hs200 = F_SDH30_EMMC_HS200; >> + else >> + priv->vendor_hs200 = 0; >> + >> + return 0; >> + >> +err_add_host: >> + clk_put(priv->clk); >> +err_clk2: >> + clk_put(priv->clk_iface); >> +err_clk1: >> + iounmap(host->ioaddr); >> +err_remap: >> +err_of_parse: >> + sdhci_free_host(host); >> +err: >> + return ret; >> +} >> + >> +static int sdhci_f_sdh30_remove(struct platform_device *pdev) >> +{ >> + struct sdhci_host *host = platform_get_drvdata(pdev); >> + struct f_sdhost_priv *priv = sdhci_priv(host); >> + struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0); >> + >> + sdhci_remove_host(host, readl(host->ioaddr + SDHCI_INT_STATUS) == >> + 0xffffffff); >> + iounmap(host->ioaddr); >> + release_mem_region(iomem->start, resource_size(iomem)); >> + >> + clk_disable_unprepare(priv->clk_iface); >> + clk_disable_unprepare(priv->clk); >> + >> + clk_put(priv->clk); >> + clk_put(priv->clk_iface); >> + >> + sdhci_free_host(host); >> + platform_set_drvdata(pdev, NULL); >> + >> + return 0; >> +} >> + >> +#ifdef CONFIG_PM_SLEEP >> +static int sdhci_f_sdh30_suspend(struct device *dev) >> +{ >> + struct sdhci_host *host = dev_get_drvdata(dev); >> + >> + return sdhci_suspend_host(host); >> +} >> + >> +static int sdhci_f_sdh30_resume(struct device *dev) >> +{ >> + struct sdhci_host *host = dev_get_drvdata(dev); >> + >> + return sdhci_resume_host(host); >> +} >> +#endif >> + >> +#ifdef CONFIG_PM_RUNTIME >> +static int sdhci_f_sdh30_runtime_suspend(struct device *dev) >> +{ >> + struct sdhci_host *host = dev_get_drvdata(dev); >> + >> + return sdhci_runtime_suspend_host(host); >> +} >> + >> +static int sdhci_f_sdh30_runtime_resume(struct device *dev) >> +{ >> + struct sdhci_host *host = dev_get_drvdata(dev); >> + >> + return sdhci_runtime_resume_host(host); >> +} >> +#endif >> + >> +#ifdef CONFIG_PM >> +static const struct dev_pm_ops sdhci_f_sdh30_pmops = { >> + SET_SYSTEM_SLEEP_PM_OPS(sdhci_f_sdh30_suspend, sdhci_f_sdh30_resume) >> + SET_RUNTIME_PM_OPS(sdhci_f_sdh30_runtime_suspend, >> + sdhci_f_sdh30_runtime_resume, NULL) >> +}; >> + >> +#define SDHCI_F_SDH30_PMOPS (&sdhci_f_sdh30_pmops) >> + >> +#else >> +#define SDHCI_F_SDH30_PMOPS NULL >> +#endif >> + >> +static const struct of_device_id f_sdh30_dt_ids[] = { >> + { .compatible = "fujitsu,mb86s70-sdh30" }, >> + { /* sentinel */ } >> +}; >> +MODULE_DEVICE_TABLE(of, f_sdh30_dt_ids); >> + >> +static struct platform_driver sdhci_f_sdh30_driver = { >> + .driver = { >> + .name = "f_sdh30", >> + .of_match_table = f_sdh30_dt_ids, >> +#ifdef CONFIG_PM_SLEEP >> + .pm = SDHCI_F_SDH30_PMOPS, >> +#endif >> + }, >> + .probe = sdhci_f_sdh30_probe, >> + .remove = sdhci_f_sdh30_remove, >> +}; >> + >> +module_platform_driver(sdhci_f_sdh30_driver); >> + >> +MODULE_DESCRIPTION("F_SDH30 SD Card Controller driver"); >> +MODULE_LICENSE("GPL v2"); >> +MODULE_AUTHOR("FUJITSU SEMICONDUCTOR LTD."); >> +MODULE_ALIAS("platform:f_sdh30"); >> -- >> 1.9.0 >> -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thu, Nov 20, 2014 at 10:59 AM, Vincent Yang <vincent.yang.fujitsu@gmail.com> wrote: > 2014-11-20 23:22 GMT+08:00 Rob Herring <robherring2@gmail.com>: >> On Thu, Nov 20, 2014 at 6:38 AM, Vincent Yang >> <vincent.yang.fujitsu@gmail.com> wrote: >>> This patch adds new host controller driver for >>> Fujitsu SDHCI controller f_sdh30. >>> >>> Signed-off-by: Andy Green <andy.green@linaro.org> >>> Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com> >>> Signed-off-by: Tetsuya Takinishi <t.takinishi@jp.fujitsu.com> >>> --- >>> .../devicetree/bindings/mmc/sdhci-fujitsu.txt | 35 +++ >>> drivers/mmc/host/Kconfig | 9 + >>> drivers/mmc/host/Makefile | 1 + >>> drivers/mmc/host/sdhci_f_sdh30.c | 319 +++++++++++++++++++++ >>> 4 files changed, 364 insertions(+) >>> create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt >>> create mode 100644 drivers/mmc/host/sdhci_f_sdh30.c >>> >>> diff --git a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt >>> new file mode 100644 >>> index 0000000..a1e0b64 >>> --- /dev/null >>> +++ b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt >>> @@ -0,0 +1,35 @@ >>> +* Fujitsu SDHCI controller >>> + >>> +This file documents differences between the core properties in mmc.txt >>> +and the properties used by the sdhci_f_sdh30 driver. >>> + >>> +Required properties: >>> +- compatible: "fujitsu,mb86s70-sdh30" >> >> It would be nice to have sdhci in the name to indicate it is an SDHCI >> controller. > > Yes, we will update it to "fujitsu,sdhci-f-sdh30" > Thanks for your review! Not really what I had in mind as you are then dropping the chip name. Perhaps "fujitsu,mb86s70-sdhci-3.0". Is 3.0 the SD spec version or IP version? If the former, I think I'd drop it as IIRC that is available in a register. Rob -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
2014-11-21 2:18 GMT+08:00 Rob Herring <robherring2@gmail.com>: > On Thu, Nov 20, 2014 at 10:59 AM, Vincent Yang > <vincent.yang.fujitsu@gmail.com> wrote: >> 2014-11-20 23:22 GMT+08:00 Rob Herring <robherring2@gmail.com>: >>> On Thu, Nov 20, 2014 at 6:38 AM, Vincent Yang >>> <vincent.yang.fujitsu@gmail.com> wrote: >>>> This patch adds new host controller driver for >>>> Fujitsu SDHCI controller f_sdh30. >>>> >>>> Signed-off-by: Andy Green <andy.green@linaro.org> >>>> Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com> >>>> Signed-off-by: Tetsuya Takinishi <t.takinishi@jp.fujitsu.com> >>>> --- >>>> .../devicetree/bindings/mmc/sdhci-fujitsu.txt | 35 +++ >>>> drivers/mmc/host/Kconfig | 9 + >>>> drivers/mmc/host/Makefile | 1 + >>>> drivers/mmc/host/sdhci_f_sdh30.c | 319 +++++++++++++++++++++ >>>> 4 files changed, 364 insertions(+) >>>> create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt >>>> create mode 100644 drivers/mmc/host/sdhci_f_sdh30.c >>>> >>>> diff --git a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt >>>> new file mode 100644 >>>> index 0000000..a1e0b64 >>>> --- /dev/null >>>> +++ b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt >>>> @@ -0,0 +1,35 @@ >>>> +* Fujitsu SDHCI controller >>>> + >>>> +This file documents differences between the core properties in mmc.txt >>>> +and the properties used by the sdhci_f_sdh30 driver. >>>> + >>>> +Required properties: >>>> +- compatible: "fujitsu,mb86s70-sdh30" >>> >>> It would be nice to have sdhci in the name to indicate it is an SDHCI >>> controller. >> >> Yes, we will update it to "fujitsu,sdhci-f-sdh30" >> Thanks for your review! > > Not really what I had in mind as you are then dropping the chip name. > Perhaps "fujitsu,mb86s70-sdhci-3.0". Is 3.0 the SD spec version or IP > version? If the former, I think I'd drop it as IIRC that is available > in a register. We will update it to "fujitsu,mb86s70-sdhci-3.0" as you suggest because 3.0 is IP version Thanks for your review! Vincent > > Rob -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt new file mode 100644 index 0000000..a1e0b64 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt @@ -0,0 +1,35 @@ +* Fujitsu SDHCI controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci_f_sdh30 driver. + +Required properties: +- compatible: "fujitsu,mb86s70-sdh30" +- voltage-ranges : This is a list of pairs. In each pair, two cells + are required. First cell specifies minimum slot voltage (mV), second + cell specifies maximum slot voltage (mV). In case of supported voltage + range is discontinuous, several ranges could be specified as a list. + +Optional properties: +- vqmmc-supply: phandle to the regulator device tree node, mentioned + as the VCCQ/VDD_IO supply in the eMMC/SD specs. +- clocks: Must contain an entry for each entry in clock-names. It is a + list of phandles and clock-specifier pairs. + See ../clocks/clock-bindings.txt for details. +- clock-names: Should contain the following two entries: + "iface" - clock used for sdhci interface + "core" - core clock for sdhci controller + +Example: + + sdhci1: sdio@36600000 { + compatible = "fujitsu,mb86s70-sdh30"; + reg = <0 0x36600000 0x1000>; + interrupts = <0 172 0x4>, + <0 173 0x4>; + voltage-ranges = <1800 1800>, <3300 3300>; + bus-width = <4>; + vqmmc-supply = <&vccq_sdhci1>; + clocks = <&clk_hdmi_2_0>, <&clk_hdmi_3_0>; + clock-names = "iface", "core"; + }; diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index 1386065..cbe5e3c 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -290,6 +290,15 @@ config MMC_SDHCI_BCM2835 This selects the BCM2835 SD/MMC controller. If you have a BCM2835 platform with SD or MMC devices, say Y or M here. +config MMC_SDHCI_F_SDH30 + tristate "SDHCI support for Fujitsu Semiconductor F_SDH30" + depends on ARCH_MB86S7X + depends on MMC_SDHCI_PLTFM + depends on OF + help + This selects the Secure Digital Host Controller Interface (SDHCI) + Needed by some Fujitsu SoC for MMC / SD / SDIO support. + If you have a controller with this interface, say Y or M here. If unsure, say N. config MMC_MOXART diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile index b09ecfb..63efc38 100644 --- a/drivers/mmc/host/Makefile +++ b/drivers/mmc/host/Makefile @@ -16,6 +16,7 @@ obj-$(CONFIG_MMC_SDHCI_PXAV3) += sdhci-pxav3.o obj-$(CONFIG_MMC_SDHCI_PXAV2) += sdhci-pxav2.o obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c.o obj-$(CONFIG_MMC_SDHCI_SIRF) += sdhci-sirf.o +obj-$(CONFIG_MMC_SDHCI_F_SDH30) += sdhci_f_sdh30.o obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o obj-$(CONFIG_MMC_WBSD) += wbsd.o obj-$(CONFIG_MMC_AU1X) += au1xmmc.o diff --git a/drivers/mmc/host/sdhci_f_sdh30.c b/drivers/mmc/host/sdhci_f_sdh30.c new file mode 100644 index 0000000..f6eba5a --- /dev/null +++ b/drivers/mmc/host/sdhci_f_sdh30.c @@ -0,0 +1,319 @@ +/* + * linux/drivers/mmc/host/sdhci_f_sdh30.c + * + * Copyright (C) 2013 - 2014 Fujitsu Semiconductor, Ltd + * Vincent Yang <vincent.yang@tw.fujitsu.com> + * Copyright (C) 2014 Linaro Ltd Andy Green <andy.green@linaro.org> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, version 2 of the License. + */ + +#include <linux/err.h> +#include <linux/delay.h> +#include <linux/module.h> +#include <linux/mmc/sd.h> +#include <linux/mmc/host.h> +#include <linux/mmc/card.h> +#include <linux/gpio.h> +#include <linux/of_gpio.h> +#include <linux/of_address.h> +#include <linux/platform_device.h> +#include <linux/pm.h> +#include <linux/pm_runtime.h> +#include <linux/suspend.h> + +#include "sdhci.h" +#include "sdhci-pltfm.h" + +/* F_SDH30 extended Controller registers */ +#define F_SDH30_AHB_CONFIG 0x100 +#define F_SDH30_AHB_BIGED 0x00000040 +#define F_SDH30_BUSLOCK_DMA 0x00000020 +#define F_SDH30_BUSLOCK_EN 0x00000010 +#define F_SDH30_SIN 0x00000008 +#define F_SDH30_AHB_INCR_16 0x00000004 +#define F_SDH30_AHB_INCR_8 0x00000002 +#define F_SDH30_AHB_INCR_4 0x00000001 + +#define F_SDH30_TUNING_SETTING 0x108 +#define F_SDH30_CMD_CHK_DIS 0x00010000 + +#define F_SDH30_IO_CONTROL2 0x114 +#define F_SDH30_CRES_O_DN 0x00080000 +#define F_SDH30_MSEL_O_1_8 0x00040000 + +#define F_SDH30_ESD_CONTROL 0x124 +#define F_SDH30_EMMC_RST 0x00000002 +#define F_SDH30_EMMC_HS200 0x01000000 + +#define F_SDH30_CMD_DAT_DELAY 0x200 + +#define F_SDH30_MIN_CLOCK 400000 + +struct f_sdhost_priv { + struct clk *clk_iface; + struct clk *clk; + u32 vendor_hs200; + struct device *dev; +}; + +void sdhci_f_sdh30_soft_voltage_switch(struct sdhci_host *host) +{ + struct f_sdhost_priv *priv = sdhci_priv(host); + u32 ctrl = 0; + + usleep_range(2500, 3000); + ctrl = sdhci_readl(host, F_SDH30_IO_CONTROL2); + ctrl |= F_SDH30_CRES_O_DN; + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2); + ctrl |= F_SDH30_MSEL_O_1_8; + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2); + + ctrl &= ~F_SDH30_CRES_O_DN; + sdhci_writel(host, ctrl, F_SDH30_IO_CONTROL2); + usleep_range(2500, 3000); + + if (priv->vendor_hs200) { + dev_info(priv->dev, "%s: setting hs200\n", __func__); + ctrl = sdhci_readl(host, F_SDH30_ESD_CONTROL); + ctrl |= priv->vendor_hs200; + sdhci_writel(host, ctrl, F_SDH30_ESD_CONTROL); + } + + ctrl = sdhci_readl(host, F_SDH30_TUNING_SETTING); + ctrl |= F_SDH30_CMD_CHK_DIS; + sdhci_writel(host, ctrl, F_SDH30_TUNING_SETTING); +} + +unsigned int sdhci_f_sdh30_get_min_clock(struct sdhci_host *host) +{ + return F_SDH30_MIN_CLOCK; +} + +void sdhci_f_sdh30_reset(struct sdhci_host *host, u8 mask) +{ + if (sdhci_readw(host, SDHCI_CLOCK_CONTROL) == 0) + sdhci_writew(host, 0xBC01, SDHCI_CLOCK_CONTROL); + + sdhci_reset(host, mask); +} + +static const struct sdhci_ops sdhci_f_sdh30_ops = { + .voltage_switch = sdhci_f_sdh30_soft_voltage_switch, + .get_min_clock = sdhci_f_sdh30_get_min_clock, + .reset = sdhci_f_sdh30_reset, + .set_clock = sdhci_set_clock, + .set_bus_width = sdhci_set_bus_width, + .set_uhs_signaling = sdhci_set_uhs_signaling, +}; + +static int sdhci_f_sdh30_probe(struct platform_device *pdev) +{ + struct sdhci_host *host; + struct device *dev = &pdev->dev; + int irq, ctrl = 0, ret = 0; + struct f_sdhost_priv *priv; + u32 reg = 0; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(dev, "%s: no irq specified\n", __func__); + ret = irq; + goto err; + } + + host = sdhci_alloc_host(dev, sizeof(struct sdhci_host) + + sizeof(struct f_sdhost_priv)); + if (IS_ERR(host)) { + dev_err(dev, "%s: host allocate error\n", __func__); + ret = -ENOMEM; + goto err; + } + priv = sdhci_priv(host); + priv->dev = dev; + + host->quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC | + SDHCI_QUIRK_INVERTED_WRITE_PROTECT; + host->quirks2 = SDHCI_QUIRK2_SUPPORT_SINGLE | + SDHCI_QUIRK2_TUNING_WORK_AROUND; + + ret = mmc_of_parse(host->mmc); + if (ret) + goto err_of_parse; + + ret = mmc_of_parse_voltage(pdev->dev.of_node, &host->ocr_mask); + if (ret) + goto err_of_parse; + + platform_set_drvdata(pdev, host); + + sdhci_get_of_property(pdev); + host->hw_name = "f_sdh30"; + host->ops = &sdhci_f_sdh30_ops; + host->irq = irq; + + host->ioaddr = of_iomap(pdev->dev.of_node, 0); + if (!host->ioaddr) { + dev_err(dev, "%s: failed to remap registers\n", __func__); + ret = -ENXIO; + goto err_remap; + } + + priv->clk_iface = clk_get(&pdev->dev, "iface"); + if (!IS_ERR(priv->clk_iface)) { + ret = clk_prepare_enable(priv->clk_iface); + if (ret < 0) { + dev_err(dev, "Failed to enable iface clock: %d\n", ret); + goto err_clk1; + } + } + priv->clk = clk_get(&pdev->dev, "core"); + if (!IS_ERR(priv->clk)) { + ret = clk_prepare_enable(priv->clk); + if (ret < 0) { + dev_err(dev, "Failed to enable core clock: %d\n", ret); + goto err_clk2; + } + } + +#ifdef CONFIG_PM_RUNTIME + pm_runtime_set_active(&pdev->dev); + pm_runtime_enable(&pdev->dev); + ret = pm_runtime_get_sync(&pdev->dev); + if (ret < 0) + dev_err(dev, "Failed to pm_runtime_get_sync: %d\n", ret); +#endif + + ret = sdhci_add_host(host); + if (ret) { + dev_err(dev, "%s: host add error\n", __func__); + goto err_add_host; + } + + /* init vendor specific regs */ + ctrl = sdhci_readw(host, F_SDH30_AHB_CONFIG); + ctrl |= F_SDH30_SIN | F_SDH30_AHB_INCR_16 | F_SDH30_AHB_INCR_8 | + F_SDH30_AHB_INCR_4; + ctrl &= ~(F_SDH30_AHB_BIGED | F_SDH30_BUSLOCK_EN); + sdhci_writew(host, ctrl, F_SDH30_AHB_CONFIG); + + reg = sdhci_readl(host, F_SDH30_ESD_CONTROL); + sdhci_writel(host, reg & ~F_SDH30_EMMC_RST, F_SDH30_ESD_CONTROL); + msleep(20); + sdhci_writel(host, reg | F_SDH30_EMMC_RST, F_SDH30_ESD_CONTROL); + + reg = sdhci_readl(host, SDHCI_CAPABILITIES); + if (reg & SDHCI_CAN_DO_8BIT) + priv->vendor_hs200 = F_SDH30_EMMC_HS200; + else + priv->vendor_hs200 = 0; + + return 0; + +err_add_host: + clk_put(priv->clk); +err_clk2: + clk_put(priv->clk_iface); +err_clk1: + iounmap(host->ioaddr); +err_remap: +err_of_parse: + sdhci_free_host(host); +err: + return ret; +} + +static int sdhci_f_sdh30_remove(struct platform_device *pdev) +{ + struct sdhci_host *host = platform_get_drvdata(pdev); + struct f_sdhost_priv *priv = sdhci_priv(host); + struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + + sdhci_remove_host(host, readl(host->ioaddr + SDHCI_INT_STATUS) == + 0xffffffff); + iounmap(host->ioaddr); + release_mem_region(iomem->start, resource_size(iomem)); + + clk_disable_unprepare(priv->clk_iface); + clk_disable_unprepare(priv->clk); + + clk_put(priv->clk); + clk_put(priv->clk_iface); + + sdhci_free_host(host); + platform_set_drvdata(pdev, NULL); + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int sdhci_f_sdh30_suspend(struct device *dev) +{ + struct sdhci_host *host = dev_get_drvdata(dev); + + return sdhci_suspend_host(host); +} + +static int sdhci_f_sdh30_resume(struct device *dev) +{ + struct sdhci_host *host = dev_get_drvdata(dev); + + return sdhci_resume_host(host); +} +#endif + +#ifdef CONFIG_PM_RUNTIME +static int sdhci_f_sdh30_runtime_suspend(struct device *dev) +{ + struct sdhci_host *host = dev_get_drvdata(dev); + + return sdhci_runtime_suspend_host(host); +} + +static int sdhci_f_sdh30_runtime_resume(struct device *dev) +{ + struct sdhci_host *host = dev_get_drvdata(dev); + + return sdhci_runtime_resume_host(host); +} +#endif + +#ifdef CONFIG_PM +static const struct dev_pm_ops sdhci_f_sdh30_pmops = { + SET_SYSTEM_SLEEP_PM_OPS(sdhci_f_sdh30_suspend, sdhci_f_sdh30_resume) + SET_RUNTIME_PM_OPS(sdhci_f_sdh30_runtime_suspend, + sdhci_f_sdh30_runtime_resume, NULL) +}; + +#define SDHCI_F_SDH30_PMOPS (&sdhci_f_sdh30_pmops) + +#else +#define SDHCI_F_SDH30_PMOPS NULL +#endif + +static const struct of_device_id f_sdh30_dt_ids[] = { + { .compatible = "fujitsu,mb86s70-sdh30" }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, f_sdh30_dt_ids); + +static struct platform_driver sdhci_f_sdh30_driver = { + .driver = { + .name = "f_sdh30", + .of_match_table = f_sdh30_dt_ids, +#ifdef CONFIG_PM_SLEEP + .pm = SDHCI_F_SDH30_PMOPS, +#endif + }, + .probe = sdhci_f_sdh30_probe, + .remove = sdhci_f_sdh30_remove, +}; + +module_platform_driver(sdhci_f_sdh30_driver); + +MODULE_DESCRIPTION("F_SDH30 SD Card Controller driver"); +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("FUJITSU SEMICONDUCTOR LTD."); +MODULE_ALIAS("platform:f_sdh30");