@@ -42,11 +42,30 @@ static unsigned int max77686_ldo_volt2hex(int ldo, ulong uV)
return 0;
}
+static int max77686_buck_volt2hex(int buck, ulong uV)
+{
+ int hex = 0;
+
+ if (buck < 5 || buck > 9) {
+ debug("%s: buck %d is not supported\n", __func__, buck);
+ return -EINVAL;
+ }
+
+ hex = (uV - 750000) / 50000;
+
+ if (hex >= 0 && hex <= MAX77686_BUCK_VOLT_MAX_HEX)
+ return hex;
+
+ debug("%s: %ld is wrong voltage value for BUCK%d\n",
+ __func__, uV, buck);
+ return -EINVAL;
+}
+
int max77686_set_ldo_voltage(struct pmic *p, int ldo, ulong uV)
{
unsigned int val, ret, hex, adr;
- if (ldo < 1 && ldo > 26) {
+ if (ldo < 1 || ldo > 26) {
printf("%s: %d is wrong ldo number\n", __func__, ldo);
return -1;
}
@@ -68,11 +87,38 @@ int max77686_set_ldo_voltage(struct pmic *p, int ldo, ulong uV)
return ret;
}
+int max77686_set_buck_voltage(struct pmic *p, int buck, ulong uV)
+{
+ unsigned int val, adr;
+ int hex, ret;
+
+ if (buck < 5 || buck > 9) {
+ printf("%s: %d is an unsupported bucket number\n",
+ __func__, buck);
+ return -EINVAL;
+ }
+
+ adr = max77686_buck_addr[buck] + 1;
+ hex = max77686_buck_volt2hex(buck, uV);
+
+ if (hex < 0)
+ return hex;
+
+ ret = pmic_reg_read(p, adr, &val);
+ if (ret)
+ return ret;
+
+ val &= ~MAX77686_BUCK_VOLT_MASK;
+ ret |= pmic_reg_write(p, adr, val | hex);
+
+ return ret;
+}
+
int max77686_set_ldo_mode(struct pmic *p, int ldo, char opmode)
{
unsigned int val, ret, adr, mode;
- if (ldo < 1 && 26 < ldo) {
+ if (ldo < 1 || 26 < ldo) {
printf("%s: %d is wrong ldo number\n", __func__, ldo);
return -1;
}
@@ -157,7 +203,7 @@ int max77686_set_buck_mode(struct pmic *p, int buck, char opmode)
/* mode */
switch (opmode) {
case OPMODE_OFF:
- mode = MAX77686_BUCK_MODE_OFF;
+ mode = MAX77686_BUCK_MODE_OFF << mode_shift;
break;
case OPMODE_STANDBY:
switch (buck) {
@@ -150,6 +150,7 @@ enum {
int max77686_set_ldo_voltage(struct pmic *p, int ldo, ulong uV);
int max77686_set_ldo_mode(struct pmic *p, int ldo, char opmode);
+int max77686_set_buck_voltage(struct pmic *p, int buck, ulong uV);
int max77686_set_buck_mode(struct pmic *p, int buck, char opmode);
#define MAX77686_LDO_VOLT_MAX_HEX 0x3f
@@ -159,6 +160,8 @@ int max77686_set_buck_mode(struct pmic *p, int buck, char opmode);
#define MAX77686_LDO_MODE_STANDBY (0x01 << 0x06)
#define MAX77686_LDO_MODE_LPM (0x02 << 0x06)
#define MAX77686_LDO_MODE_ON (0x03 << 0x06)
+#define MAX77686_BUCK_VOLT_MAX_HEX 0x3f
+#define MAX77686_BUCK_VOLT_MASK 0x3f
#define MAX77686_BUCK_MODE_MASK 0x03
#define MAX77686_BUCK_MODE_SHIFT_1 0x00
#define MAX77686_BUCK_MODE_SHIFT_2 0x04
Allow to set the buck voltage for the max77686. This will be used to reset the SMC LAN9730 ethernet on the odroids. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> --- Changes in v3: * Correct ldo and buck validation logic * Jaehoon/Przemyslaw - Use negative errno values for error condistions * Albert - its buck not bucket Changes in v2: * Jaehoon - separate out this patch Changes in v1: - First try drivers/power/pmic/pmic_max77686.c | 52 +++++++++++++++++++++++++++++++++++--- include/power/max77686_pmic.h | 3 +++ 2 files changed, 52 insertions(+), 3 deletions(-)