Patchwork [5/5] libata/drivers: Add pata_macio, driver Apple PowerMac/PowerBook IDE controller

login
register
mail settings
Submitter Benjamin Herrenschmidt
Date Dec. 1, 2009, 7:08 a.m.
Message ID <20091201070834.6A840B7B63@ozlabs.org>
Download mbox | patch
Permalink /patch/39884/
State Not Applicable
Delegated to: David Miller
Headers show

Comments

Benjamin Herrenschmidt - Dec. 1, 2009, 7:08 a.m.
This is a libata driver for the "macio" IDE controller used on most Apple
PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c

It supports all the features of its predecessor, including mediabay hotplug
and suspend/resume. It should also support module load/unload.

The timing calculations have been simplified to use pre-calculated tables
compared to drivers/ide/pmac.c and it uses the new mediabay interface
provided by a previous patch.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---

Only lightly tested so far, this is for review, NOT for merge.

I would like to merge it eventually via the powerpc tree since there's a
few dependent patches, though I would need the libata "fix" for
bmdma_stop to go in first, unless I carry it as well with appropriate
acks.

I have addressed some of the comments from the previous version (almost a
year ago I think). I have kept the single function for the PIO and DMA
timings due to the one bit overlap between the fields in the HW register
on the shasta chipset. It seems to work fine.


 drivers/ata/Kconfig      |   10 
 drivers/ata/Makefile     |    1 
 drivers/ata/pata_macio.c | 1390 +++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 1401 insertions(+)

--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Tejun Heo - Dec. 1, 2009, 8 a.m.
(cc'ing Holger Macht, please read the comment below pata_macio_mb_event())
Hello,

On 12/01/2009 04:08 PM, Benjamin Herrenschmidt wrote:
> This is a libata driver for the "macio" IDE controller used on most Apple
> PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c

Don't know much about the controller or the platform so my comments
will be pretty confined.

> +/*
> + * Wait 1s for disk to answer on IDE bus after a hard reset
> + * of the device (via GPIO/FCR).
> + *
> + * Some devices seem to "pollute" the bus even after dropping
> + * the BSY bit (typically some combo drives slave on the UDMA
> + * bus) after a hard reset. Since we hard reset all drives on
> + * KeyLargo ATA66, we have to keep that delay around. I may end
> + * up not hard resetting anymore on these and keep the delay only
> + * for older interfaces instead (we have to reset when coming
> + * from MacOS...) --BenH.
> + */
> +#define IDE_WAKEUP_DELAY	(1*HZ)

nitpick: In libata, it's common to use msecs for timing values so that
might be a better option.

> +static const struct pata_macio_timing *pata_macio_find_timing(
> +					    struct pata_macio_priv *priv,
> +					    int mode)
> +{
> +	int i = 0;
> +
> +	while (priv->timings[i].mode > 0) {
> +		if (priv->timings[i].mode == mode)
> +			return &priv->timings[i];
> +		i++;
> +	}
> +	return NULL;

Wouldn't for (i = 0; ...) look better?

> +static void pata_macio_bmdma_start(struct ata_queued_cmd *qc)
> +{
> +	struct ata_port *ap = qc->ap;
> +	struct pata_macio_priv *priv = ap->private_data;
> +	struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
> +
> +	dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc);
> +
> +	writel((RUN << 16) | RUN, &dma_regs->control);
> +	/* Make sure it gets to the controller right now */
> +	(void)readl(&dma_regs->control);

Is flushing necessary here?  There's no ordering issue here, right?

> +static void pata_macio_bmdma_stop(struct ata_queued_cmd *qc)
> +{
> +	struct ata_port *ap = qc->ap;
> +	struct pata_macio_priv *priv = ap->private_data;
> +	struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
> +
> +	dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc);
> +
> +	/* Stop the DMA engine and wait for it to full halt */
> +	writel (((RUN|WAKE|DEAD) << 16), &dma_regs->control);
> +	while (readl(&dma_regs->status) & RUN)
> +		udelay(1);

Heh... this is a scary looking loop.  It would be great if the above
loop can be capped somehow.

> +static u8 pata_macio_bmdma_status(struct ata_port *ap)
> +{
> +	struct pata_macio_priv *priv = ap->private_data;
> +	struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
> +	u32 dstat, rstat = ATA_DMA_INTR;
> +	unsigned long timeout = 0;
> +
> +	dstat = readl(&dma_regs->status);
> +
> +	dev_dbgdma(priv->dev, "%s: dstat=%x\n", __func__, dstat);
> +
> +	/* We have to things to deal with here:
                   ^^
                   two

> +/* port_start is when we allocate the DMA command list */
> +static int pata_macio_port_start(struct ata_port *ap)
> +{
> +	struct pata_macio_priv *priv = ap->private_data;
> +	struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
> +
> +	if (dma_regs == NULL)
> +		return 0;
> +
> +	/* Make sure DMA controller is stopped */
> +	writel((RUN|PAUSE|FLUSH|WAKE|DEAD) << 16, &dma_regs->control);
> +	while (readl(&dma_regs->status) & RUN)
> +		udelay(1);

Hmmm.... this probably belongs to ->freeze() which is responsible for
stopping any in-flight operations and masking IRQ and libata will call
it during initialization before requesting IRQ, so you won't need to
call it explicitly here.

> +#ifdef CONFIG_PMAC_MEDIABAY
> +static void pata_macio_mb_event(struct macio_dev* mdev, int mb_state)
> +{
> +	struct ata_host *host = macio_get_drvdata(mdev);
> +	struct ata_port *ap;
> +	struct ata_eh_info *ehi;
> +	struct ata_device *dev;
> +	unsigned long flags;
> +
> +	if (!host)
> +		return;
> +	ap = host->ports[0];
> +	spin_lock_irqsave(ap->lock, flags);
> +	ehi = &ap->link.eh_info;
> +	if (mb_state == MB_CD) {
> +		ata_ehi_push_desc(ehi, "mediabay plug");
> +		ata_ehi_hotplugged(ehi);
> +		ata_port_freeze(ap);
> +	} else {
> +		ata_ehi_push_desc(ehi, "mediabay unplug");
> +		ata_for_each_dev(dev, &ap->link, ALL)
> +			dev->flags |= ATA_DFLAG_DETACH;
> +		ata_port_schedule_eh(ap);

I think you'll need an ata_port_freeze() or abort() here because at
this point the drive is already gone and all in-flight commands need
to be failed right away.  Holger, do you remember why
ata_acpi_detach_device() is using ata_port_schedule_eh() instead?  Was
it because ata_port_freeze() might end up poking registers after
hotunplug happened?  ISTR reports where accessing any register there
causing the whole system to lock up but then why can't it use
ata_port_abort() instead?

Thanks.
Mikael Pettersson - Dec. 1, 2009, 10:48 a.m.
Benjamin Herrenschmidt writes:
 > This is a libata driver for the "macio" IDE controller used on most Apple
 > PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c
 > 
 > It supports all the features of its predecessor, including mediabay hotplug
 > and suspend/resume. It should also support module load/unload.
 > 
 > The timing calculations have been simplified to use pre-calculated tables
 > compared to drivers/ide/pmac.c and it uses the new mediabay interface
 > provided by a previous patch.
 > 
 > Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
 > ---
 > 
 > Only lightly tested so far, this is for review, NOT for merge.
 > 
 > I would like to merge it eventually via the powerpc tree since there's a
 > few dependent patches, though I would need the libata "fix" for
 > bmdma_stop to go in first, unless I carry it as well with appropriate
 > acks.
 > 
 > I have addressed some of the comments from the previous version (almost a
 > year ago I think). I have kept the single function for the PIO and DMA
 > timings due to the one bit overlap between the fields in the HW register
 > on the shasta chipset. It seems to work fine.

Thanks for reviving pata_macio.

Does the new version work with yaboot? (the previous one didn't)

/Mikael
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Benjamin Herrenschmidt - Dec. 1, 2009, 10:53 a.m.
On Tue, 2009-12-01 at 11:48 +0100, Mikael Pettersson wrote:
> Thanks for reviving pata_macio.
> 
> Does the new version work with yaboot? (the previous one didn't)

Well, yaboot itself should have no problem. However, the ybin script
that automagically finds the right OF path might indeed still be busted,
it will have to be updated I'm afraid as it's more/less hard coded to
know about IDE gunk

I'll have a look. The new yaboot maintainer (Tony Breeds) happens to sit
2 cubicles away from me at work so it shouldn't be a huge deal.

Thanks for reminding me tho !

Cheers,
Ben.


--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Holger Macht - Dec. 1, 2009, 12:44 p.m.
On Tuesday 01 December 2009 09:00:34 Tejun Heo wrote:
> (cc'ing Holger Macht, please read the comment below pata_macio_mb_event())
> Hello,
> 
> On 12/01/2009 04:08 PM, Benjamin Herrenschmidt wrote:
> > This is a libata driver for the "macio" IDE controller used on most Apple
> > PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c
[...]
> > +#ifdef CONFIG_PMAC_MEDIABAY
> > +static void pata_macio_mb_event(struct macio_dev* mdev, int mb_state)
> > +{
> > +	struct ata_host *host = macio_get_drvdata(mdev);
> > +	struct ata_port *ap;
> > +	struct ata_eh_info *ehi;
> > +	struct ata_device *dev;
> > +	unsigned long flags;
> > +
> > +	if (!host)
> > +		return;
> > +	ap = host->ports[0];
> > +	spin_lock_irqsave(ap->lock, flags);
> > +	ehi = &ap->link.eh_info;
> > +	if (mb_state == MB_CD) {
> > +		ata_ehi_push_desc(ehi, "mediabay plug");
> > +		ata_ehi_hotplugged(ehi);
> > +		ata_port_freeze(ap);
> > +	} else {
> > +		ata_ehi_push_desc(ehi, "mediabay unplug");
> > +		ata_for_each_dev(dev, &ap->link, ALL)
> > +			dev->flags |= ATA_DFLAG_DETACH;
> > +		ata_port_schedule_eh(ap);
> 
> I think you'll need an ata_port_freeze() or abort() here because at
> this point the drive is already gone and all in-flight commands need
> to be failed right away.  Holger, do you remember why
> ata_acpi_detach_device() is using ata_port_schedule_eh() instead?  Was
> it because ata_port_freeze() might end up poking registers after
> hotunplug happened?  ISTR reports where accessing any register there
> causing the whole system to lock up but then why can't it use
> ata_port_abort() instead?

I do not remember any specific reason for using ata_port_schedule_eh(). I
guess it's just there because the previous implementation used
it. ata_port_freeze()/abort() might as well work properly. However, I
would hesitate to change the existing code, because verifying that
everything works contains quite some effort. There are so many different
use cases this code can be accessed with and it has to be verified with
all kind of different hardware to make sure we get no hard
freezes. Testing that freeze()/abort() in this new driver would be worth a
try, though. Next time I have setup my test environment again I can verify
that it also works in the general libata-acpi code.

Regards,
 Holger
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Tejun Heo - Dec. 1, 2009, 12:48 p.m.
On 12/01/2009 09:44 PM, Holger Macht wrote:
> I do not remember any specific reason for using ata_port_schedule_eh(). I
> guess it's just there because the previous implementation used
> it. ata_port_freeze()/abort() might as well work properly. However, I
> would hesitate to change the existing code, because verifying that
> everything works contains quite some effort. There are so many different
> use cases this code can be accessed with and it has to be verified with
> all kind of different hardware to make sure we get no hard
> freezes. Testing that freeze()/abort() in this new driver would be worth a
> try, though. Next time I have setup my test environment again I can verify
> that it also works in the general libata-acpi code.

Yeap, agreed.  It was pretty painful get it right the last time
around, so changing it on a hunch would be a pretty bad idea.  If you
have a chance to try freeze or abort, please keep me posted.

Thanks.
Andreas Schwab - Dec. 1, 2009, 8:43 p.m.
Benjamin Herrenschmidt <benh@kernel.crashing.org> writes:

> This is a libata driver for the "macio" IDE controller used on most Apple
> PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c

Tried it on my iBook G4 and I got an oops during probing, in
pata_macio_common_init+0x378/0x614.

Andreas.
Benjamin Herrenschmidt - Dec. 1, 2009, 10:34 p.m.
On Tue, 2009-12-01 at 21:43 +0100, Andreas Schwab wrote:
> Benjamin Herrenschmidt <benh@kernel.crashing.org> writes:
> 
> > This is a libata driver for the "macio" IDE controller used on most Apple
> > PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c
> 
> Tried it on my iBook G4 and I got an oops during probing, in
> pata_macio_common_init+0x378/0x614.

Any chance you can send me the oops log ? (you have a digital
camera ? :-)

What model of ibook ? There's one here I could try on I think but it
might not be the same model.

Cheers,
Ben.


--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Benjamin Herrenschmidt - Dec. 1, 2009, 10:58 p.m.
On Tue, 2009-12-01 at 21:43 +0100, Andreas Schwab wrote:
> Benjamin Herrenschmidt <benh@kernel.crashing.org> writes:
> 
> > This is a libata driver for the "macio" IDE controller used on most Apple
> > PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c
> 
> Tried it on my iBook G4 and I got an oops during probing, in
> pata_macio_common_init+0x378/0x614.

Bah, I know what it is ... a last minute cleanup that breaks the PCI
variants of the cell. I'll send a new patch later today along with
other fixes.

Cheers,
Ben.


--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Benjamin Herrenschmidt - Dec. 1, 2009, 11:19 p.m.
On Tue, 2009-12-01 at 17:00 +0900, Tejun Heo wrote:

> > +#define IDE_WAKEUP_DELAY	(1*HZ)
> 
> nitpick: In libata, it's common to use msecs for timing values so that
> might be a better option.

Yeah, that's cruft lifted from the old driver, I'll fix it.

> > +static const struct pata_macio_timing *pata_macio_find_timing(
> > +					    struct pata_macio_priv *priv,
> > +					    int mode)
> > +{
> > +	int i = 0;
> > +
> > +	while (priv->timings[i].mode > 0) {
> > +		if (priv->timings[i].mode == mode)
> > +			return &priv->timings[i];
> > +		i++;
> > +	}
> > +	return NULL;
> 
> Wouldn't for (i = 0; ...) look better?

Yeah, I suppose so :-)

> > +static void pata_macio_bmdma_start(struct ata_queued_cmd *qc)
> > +{
> > +	struct ata_port *ap = qc->ap;
> > +	struct pata_macio_priv *priv = ap->private_data;
> > +	struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
> > +
> > +	dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc);
> > +
> > +	writel((RUN << 16) | RUN, &dma_regs->control);
> > +	/* Make sure it gets to the controller right now */
> > +	(void)readl(&dma_regs->control);
> 
> Is flushing necessary here?  There's no ordering issue here, right?

That's also lifted pretty-much as-is from the old driver. Now I probably
wrote that part of the old driver too ages ago :-) I think I just want
to make sure the DMA starts asap and doesn't sit in some bridge write
posting queue for hundreds of cycles.

> > +static void pata_macio_bmdma_stop(struct ata_queued_cmd *qc)
> > +{
> > +	struct ata_port *ap = qc->ap;
> > +	struct pata_macio_priv *priv = ap->private_data;
> > +	struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
> > +
> > +	dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc);
> > +
> > +	/* Stop the DMA engine and wait for it to full halt */
> > +	writel (((RUN|WAKE|DEAD) << 16), &dma_regs->control);
> > +	while (readl(&dma_regs->status) & RUN)
> > +		udelay(1);
> 
> Heh... this is a scary looking loop.  It would be great if the above
> loop can be capped somehow.

Yeah, again, lifted from the old driver. We do that sort of loops in
various other drivers that use those DBDMA channels and I don't think
ever saw the loop hang, so at least those HW aren't -that- broken but I
suppose a little timeout wouldn't hurt. Not sure what to do if we hit it
tho.
 
> > +static u8 pata_macio_bmdma_status(struct ata_port *ap)
> > +{
> > +	struct pata_macio_priv *priv = ap->private_data;
> > +	struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
> > +	u32 dstat, rstat = ATA_DMA_INTR;
> > +	unsigned long timeout = 0;
> > +
> > +	dstat = readl(&dma_regs->status);
> > +
> > +	dev_dbgdma(priv->dev, "%s: dstat=%x\n", __func__, dstat);
> > +
> > +	/* We have to things to deal with here:
>                    ^^
>                    two

Yup.

> > +/* port_start is when we allocate the DMA command list */
> > +static int pata_macio_port_start(struct ata_port *ap)
> > +{
> > +	struct pata_macio_priv *priv = ap->private_data;
> > +	struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
> > +
> > +	if (dma_regs == NULL)
> > +		return 0;
> > +
> > +	/* Make sure DMA controller is stopped */
> > +	writel((RUN|PAUSE|FLUSH|WAKE|DEAD) << 16, &dma_regs->control);
> > +	while (readl(&dma_regs->status) & RUN)
> > +		udelay(1);
> 
> Hmmm.... this probably belongs to ->freeze() which is responsible for
> stopping any in-flight operations and masking IRQ and libata will call
> it during initialization before requesting IRQ, so you won't need to
> call it explicitly here.

Well, I'm not sure I really -need- the above thing. It's there mostly
for the sake of paranoia. I suppose in case the firmware left it in some
stange state. Anyway, will move to freeze.

> > +#ifdef CONFIG_PMAC_MEDIABAY
> > +static void pata_macio_mb_event(struct macio_dev* mdev, int mb_state)
> > +{
> > +	struct ata_host *host = macio_get_drvdata(mdev);
> > +	struct ata_port *ap;
> > +	struct ata_eh_info *ehi;
> > +	struct ata_device *dev;
> > +	unsigned long flags;
> > +
> > +	if (!host)
> > +		return;
> > +	ap = host->ports[0];
> > +	spin_lock_irqsave(ap->lock, flags);
> > +	ehi = &ap->link.eh_info;
> > +	if (mb_state == MB_CD) {
> > +		ata_ehi_push_desc(ehi, "mediabay plug");
> > +		ata_ehi_hotplugged(ehi);
> > +		ata_port_freeze(ap);
> > +	} else {
> > +		ata_ehi_push_desc(ehi, "mediabay unplug");
> > +		ata_for_each_dev(dev, &ap->link, ALL)
> > +			dev->flags |= ATA_DFLAG_DETACH;
> > +		ata_port_schedule_eh(ap);
> 
> I think you'll need an ata_port_freeze() or abort() here because at
> this point the drive is already gone and all in-flight commands need
> to be failed right away.  Holger, do you remember why
> ata_acpi_detach_device() is using ata_port_schedule_eh() instead?  Was
> it because ata_port_freeze() might end up poking registers after
> hotunplug happened?  ISTR reports where accessing any register there
> causing the whole system to lock up but then why can't it use
> ata_port_abort() instead?

I'll try. Which one ? freeze or abort tho ?

Cheers,
Ben.


--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Tejun Heo - Dec. 1, 2009, 11:27 p.m.
Hello,

On 12/02/2009 08:19 AM, Benjamin Herrenschmidt wrote:
>> I think you'll need an ata_port_freeze() or abort() here because at
>> this point the drive is already gone and all in-flight commands need
>> to be failed right away.  Holger, do you remember why
>> ata_acpi_detach_device() is using ata_port_schedule_eh() instead?  Was
>> it because ata_port_freeze() might end up poking registers after
>> hotunplug happened?  ISTR reports where accessing any register there
>> causing the whole system to lock up but then why can't it use
>> ata_port_abort() instead?
> 
> I'll try. Which one ? freeze or abort tho ?

Conceptually freeze would be more approriate but the side effect is
that the port is frozen and EH will try to thaw it by resetting it.
So, abort would work better.

Thanks.
Benjamin Herrenschmidt - Dec. 1, 2009, 11:35 p.m.
On Wed, 2009-12-02 at 08:27 +0900, Tejun Heo wrote:
> Conceptually freeze would be more approriate but the side effect is
> that the port is frozen and EH will try to thaw it by resetting it.
> So, abort would work better.

BTW. For a plug event, what should I do ? freeze is fine ? Or just
schedule eh ? Right now, when plugging I see an exception Emask 0x10
etc... message in the log when plugging which isn't totally nice :-)

Cheers,
Ben.

--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Tejun Heo - Dec. 1, 2009, 11:44 p.m.
On 12/02/2009 08:35 AM, Benjamin Herrenschmidt wrote:
> On Wed, 2009-12-02 at 08:27 +0900, Tejun Heo wrote:
>> Conceptually freeze would be more approriate but the side effect is
>> that the port is frozen and EH will try to thaw it by resetting it.
>> So, abort would work better.
> 
> BTW. For a plug event, what should I do ? freeze is fine ? Or just
> schedule eh ? Right now, when plugging I see an exception Emask 0x10
> etc... message in the log when plugging which isn't totally nice :-)

freeze() and please don't fight the EH messages from low level driver.
If it's too much, we need to update core layer but given the variety
of phy related bugs, I think we need those messages.

Thanks.
Benjamin Herrenschmidt - Dec. 2, 2009, midnight
On Wed, 2009-12-02 at 08:44 +0900, Tejun Heo wrote:
> > BTW. For a plug event, what should I do ? freeze is fine ? Or just
> > schedule eh ? Right now, when plugging I see an exception Emask 0x10
> > etc... message in the log when plugging which isn't totally nice :-)
> 
> freeze() and please don't fight the EH messages from low level driver.
> If it's too much, we need to update core layer but given the variety
> of phy related bugs, I think we need those messages.

Eh, ok :-) No biggie.

Cheers,
Ben.


--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Patch

--- /dev/null	1970-01-01 00:00:00.000000000 +0000
+++ linux-work/drivers/ata/pata_macio.c	2009-12-01 17:48:48.000000000 +1100
@@ -0,0 +1,1390 @@ 
+/*
+ * Libata based driver for Apple "macio" family of PATA controllers
+ *
+ * Copyright 2008/2009 Benjamin Herrenschmidt, IBM Corp
+ *                     <benh@kernel.crashing.org>
+ *
+ * Some bits and pieces from drivers/ide/ppc/pmac.c
+ *
+ */
+
+#undef DEBUG
+#undef DEBUG_DMA
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/ata.h>
+#include <linux/libata.h>
+#include <linux/adb.h>
+#include <linux/pmu.h>
+#include <linux/scatterlist.h>
+#include <linux/of.h>
+
+#include <scsi/scsi.h>
+#include <scsi/scsi_host.h>
+#include <scsi/scsi_device.h>
+
+#include <asm/macio.h>
+#include <asm/io.h>
+#include <asm/dbdma.h>
+#include <asm/pci-bridge.h>
+#include <asm/machdep.h>
+#include <asm/pmac_feature.h>
+#include <asm/mediabay.h>
+
+#ifdef DEBUG_DMA
+#define dev_dbgdma(dev, format, arg...)		\
+	dev_printk(KERN_DEBUG , dev , format , ## arg)
+#else
+#define dev_dbgdma(dev, format, arg...)		\
+	({ if (0) dev_printk(KERN_DEBUG, dev, format, ##arg); 0; })
+#endif
+
+#define DRV_NAME	"pata_macio"
+#define DRV_VERSION	"0.9"
+
+/* Models of macio ATA controller */
+enum {
+	controller_ohare,	/* OHare based */
+	controller_heathrow,	/* Heathrow/Paddington */
+	controller_kl_ata3,	/* KeyLargo ATA-3 */
+	controller_kl_ata4,	/* KeyLargo ATA-4 */
+	controller_un_ata6,	/* UniNorth2 ATA-6 */
+	controller_k2_ata6,	/* K2 ATA-6 */
+	controller_sh_ata6,	/* Shasta ATA-6 */
+};
+
+static const char* macio_ata_names[] = {
+	"OHare ATA",		/* OHare based */
+	"Heathrow ATA",		/* Heathrow/Paddington */
+	"KeyLargo ATA-3",	/* KeyLargo ATA-3 (MDMA only) */
+	"KeyLargo ATA-4",	/* KeyLargo ATA-4 (UDMA/66) */
+	"UniNorth ATA-6",	/* UniNorth2 ATA-6 (UDMA/100) */
+	"K2 ATA-6",		/* K2 ATA-6 (UDMA/100) */
+	"Shasta ATA-6",		/* Shasta ATA-6 (UDMA/133) */
+};
+
+/*
+ * Extra registers, both 32-bit little-endian
+ */
+#define IDE_TIMING_CONFIG	0x200
+#define IDE_INTERRUPT		0x300
+
+/* Kauai (U2) ATA has different register setup */
+#define IDE_KAUAI_PIO_CONFIG	0x200
+#define IDE_KAUAI_ULTRA_CONFIG	0x210
+#define IDE_KAUAI_POLL_CONFIG	0x220
+
+/*
+ * Timing configuration register definitions
+ */
+
+/* Number of IDE_SYSCLK_NS ticks, argument is in nanoseconds */
+#define SYSCLK_TICKS(t)		(((t) + IDE_SYSCLK_NS - 1) / IDE_SYSCLK_NS)
+#define SYSCLK_TICKS_66(t)	(((t) + IDE_SYSCLK_66_NS - 1) / IDE_SYSCLK_66_NS)
+#define IDE_SYSCLK_NS		30	/* 33Mhz cell */
+#define IDE_SYSCLK_66_NS	15	/* 66Mhz cell */
+
+/* 133Mhz cell, found in shasta.
+ * See comments about 100 Mhz Uninorth 2...
+ * Note that PIO_MASK and MDMA_MASK seem to overlap, that's just
+ * weird and I don't now why .. at this stage
+ */
+#define TR_133_PIOREG_PIO_MASK		0xff000fff
+#define TR_133_PIOREG_MDMA_MASK		0x00fff800
+#define TR_133_UDMAREG_UDMA_MASK	0x0003ffff
+#define TR_133_UDMAREG_UDMA_EN		0x00000001
+
+/* 100Mhz cell, found in Uninorth 2 and K2. It appears as a pci device
+ * (106b/0033) on uninorth or K2 internal PCI bus and it's clock is
+ * controlled like gem or fw. It appears to be an evolution of keylargo
+ * ATA4 with a timing register extended to 2x32bits registers (one
+ * for PIO & MWDMA and one for UDMA, and a similar DBDMA channel.
+ * It has it's own local feature control register as well.
+ *
+ * After scratching my mind over the timing values, at least for PIO
+ * and MDMA, I think I've figured the format of the timing register,
+ * though I use pre-calculated tables for UDMA as usual...
+ */
+#define TR_100_PIO_ADDRSETUP_MASK	0xff000000 /* Size of field unknown */
+#define TR_100_PIO_ADDRSETUP_SHIFT	24
+#define TR_100_MDMA_MASK		0x00fff000
+#define TR_100_MDMA_RECOVERY_MASK	0x00fc0000
+#define TR_100_MDMA_RECOVERY_SHIFT	18
+#define TR_100_MDMA_ACCESS_MASK		0x0003f000
+#define TR_100_MDMA_ACCESS_SHIFT	12
+#define TR_100_PIO_MASK			0xff000fff
+#define TR_100_PIO_RECOVERY_MASK	0x00000fc0
+#define TR_100_PIO_RECOVERY_SHIFT	6
+#define TR_100_PIO_ACCESS_MASK		0x0000003f
+#define TR_100_PIO_ACCESS_SHIFT		0
+
+#define TR_100_UDMAREG_UDMA_MASK	0x0000ffff
+#define TR_100_UDMAREG_UDMA_EN		0x00000001
+
+
+/* 66Mhz cell, found in KeyLargo. Can do ultra mode 0 to 2 on
+ * 40 connector cable and to 4 on 80 connector one.
+ * Clock unit is 15ns (66Mhz)
+ *
+ * 3 Values can be programmed:
+ *  - Write data setup, which appears to match the cycle time. They
+ *    also call it DIOW setup.
+ *  - Ready to pause time (from spec)
+ *  - Address setup. That one is weird. I don't see where exactly
+ *    it fits in UDMA cycles, I got it's name from an obscure piece
+ *    of commented out code in Darwin. They leave it to 0, we do as
+ *    well, despite a comment that would lead to think it has a
+ *    min value of 45ns.
+ * Apple also add 60ns to the write data setup (or cycle time ?) on
+ * reads.
+ */
+#define TR_66_UDMA_MASK			0xfff00000
+#define TR_66_UDMA_EN			0x00100000 /* Enable Ultra mode for DMA */
+#define TR_66_PIO_ADDRSETUP_MASK	0xe0000000 /* Address setup */
+#define TR_66_PIO_ADDRSETUP_SHIFT	29
+#define TR_66_UDMA_RDY2PAUS_MASK	0x1e000000 /* Ready 2 pause time */
+#define TR_66_UDMA_RDY2PAUS_SHIFT	25
+#define TR_66_UDMA_WRDATASETUP_MASK	0x01e00000 /* Write data setup time */
+#define TR_66_UDMA_WRDATASETUP_SHIFT	21
+#define TR_66_MDMA_MASK			0x000ffc00
+#define TR_66_MDMA_RECOVERY_MASK	0x000f8000
+#define TR_66_MDMA_RECOVERY_SHIFT	15
+#define TR_66_MDMA_ACCESS_MASK		0x00007c00
+#define TR_66_MDMA_ACCESS_SHIFT		10
+#define TR_66_PIO_MASK			0xe00003ff
+#define TR_66_PIO_RECOVERY_MASK		0x000003e0
+#define TR_66_PIO_RECOVERY_SHIFT	5
+#define TR_66_PIO_ACCESS_MASK		0x0000001f
+#define TR_66_PIO_ACCESS_SHIFT		0
+
+/* 33Mhz cell, found in OHare, Heathrow (& Paddington) and KeyLargo
+ * Can do pio & mdma modes, clock unit is 30ns (33Mhz)
+ *
+ * The access time and recovery time can be programmed. Some older
+ * Darwin code base limit OHare to 150ns cycle time. I decided to do
+ * the same here fore safety against broken old hardware ;)
+ * The HalfTick bit, when set, adds half a clock (15ns) to the access
+ * time and removes one from recovery. It's not supported on KeyLargo
+ * implementation afaik. The E bit appears to be set for PIO mode 0 and
+ * is used to reach long timings used in this mode.
+ */
+#define TR_33_MDMA_MASK			0x003ff800
+#define TR_33_MDMA_RECOVERY_MASK	0x001f0000
+#define TR_33_MDMA_RECOVERY_SHIFT	16
+#define TR_33_MDMA_ACCESS_MASK		0x0000f800
+#define TR_33_MDMA_ACCESS_SHIFT		11
+#define TR_33_MDMA_HALFTICK		0x00200000
+#define TR_33_PIO_MASK			0x000007ff
+#define TR_33_PIO_E			0x00000400
+#define TR_33_PIO_RECOVERY_MASK		0x000003e0
+#define TR_33_PIO_RECOVERY_SHIFT	5
+#define TR_33_PIO_ACCESS_MASK		0x0000001f
+#define TR_33_PIO_ACCESS_SHIFT		0
+
+/*
+ * Interrupt register definitions
+ */
+#define IDE_INTR_DMA			0x80000000
+#define IDE_INTR_DEVICE			0x40000000
+
+/*
+ * FCR Register on Kauai. Not sure what bit 0x4 is  ...
+ */
+#define KAUAI_FCR_UATA_MAGIC		0x00000004
+#define KAUAI_FCR_UATA_RESET_N		0x00000002
+#define KAUAI_FCR_UATA_ENABLE		0x00000001
+
+
+/* Allow up to 256 DBDMA commands per xfer */
+#define MAX_DCMDS		256
+
+/* Don't let a DMA segment go all the way to 64K */
+#define MAX_DBDMA_SEG		0xff00
+
+
+/*
+ * Wait 1s for disk to answer on IDE bus after a hard reset
+ * of the device (via GPIO/FCR).
+ *
+ * Some devices seem to "pollute" the bus even after dropping
+ * the BSY bit (typically some combo drives slave on the UDMA
+ * bus) after a hard reset. Since we hard reset all drives on
+ * KeyLargo ATA66, we have to keep that delay around. I may end
+ * up not hard resetting anymore on these and keep the delay only
+ * for older interfaces instead (we have to reset when coming
+ * from MacOS...) --BenH.
+ */
+#define IDE_WAKEUP_DELAY	(1*HZ)
+
+struct pata_macio_timing;
+
+struct pata_macio_priv {
+	int				kind;
+	int				aapl_bus_id;
+	int				cable_80 : 1;
+	int				mediabay : 1;
+	struct device_node		*node;
+	struct macio_dev		*mdev;
+	struct pci_dev			*pdev;
+	struct device			*dev;
+	int				irq;
+	u32				treg[2][2];
+	void __iomem			*tfregs;
+	void __iomem			*kauai_fcr;
+	struct dbdma_cmd *		dma_table_cpu;
+	dma_addr_t			dma_table_dma;
+	struct ata_host			*host;
+	const struct pata_macio_timing	*timings;
+};
+
+/* Previous variants of this driver used to calculate timings
+ * for various variants of the chip and use tables for others.
+ *
+ * Not only was this confusing, but in addition, it isn't clear
+ * whether our calculation code was correct. It didn't entirely
+ * match the darwin code and whatever documentation I could find
+ * on these cells
+ *
+ * I decided to entirely rely on a table instead for this version
+ * of the driver. Also, because I don't really care about derated
+ * modes and really old HW other than making it work, I'm not going
+ * to calculate / snoop timing values for something else than the
+ * standard modes.
+ */
+struct pata_macio_timing {
+	int	mode;
+	u32	reg1;	/* Bits to set in first timing reg */
+	u32	reg2;	/* Bits to set in second timing reg */
+};
+
+static const struct pata_macio_timing pata_macio_ohare_timings[] = {
+	{ XFER_PIO_0,		0x00000526,	0, },
+	{ XFER_PIO_1,		0x00000085,	0, },
+	{ XFER_PIO_2,		0x00000025,	0, },
+	{ XFER_PIO_3,		0x00000025,	0, },
+	{ XFER_PIO_4,		0x00000025,	0, },
+	{ XFER_MW_DMA_0,	0x00074000,	0, },
+	{ XFER_MW_DMA_1,	0x00221000,	0, },
+	{ XFER_MW_DMA_2,	0x00211000,	0, },
+	{ -1, 0, 0 }
+};
+
+static const struct pata_macio_timing pata_macio_heathrow_timings[] = {
+	{ XFER_PIO_0,		0x00000526,	0, },
+	{ XFER_PIO_1,		0x00000085,	0, },
+	{ XFER_PIO_2,		0x00000025,	0, },
+	{ XFER_PIO_3,		0x00000025,	0, },
+	{ XFER_PIO_4,		0x00000025,	0, },
+	{ XFER_MW_DMA_0,	0x00074000,	0, },
+	{ XFER_MW_DMA_1,	0x00221000,	0, },
+	{ XFER_MW_DMA_2,	0x00211000,	0, },
+	{ -1, 0, 0 }
+};
+
+static const struct pata_macio_timing pata_macio_kl33_timings[] = {
+	{ XFER_PIO_0,		0x00000526,	0, },
+	{ XFER_PIO_1,		0x00000085,	0, },
+	{ XFER_PIO_2,		0x00000025,	0, },
+	{ XFER_PIO_3,		0x00000025,	0, },
+	{ XFER_PIO_4,		0x00000025,	0, },
+	{ XFER_MW_DMA_0,	0x00084000,	0, },
+	{ XFER_MW_DMA_1,	0x00021800,	0, },
+	{ XFER_MW_DMA_2,	0x00011800,	0, },
+	{ -1, 0, 0 }
+};
+
+static const struct pata_macio_timing pata_macio_kl66_timings[] = {
+	{ XFER_PIO_0,		0x0000038c,	0, },
+	{ XFER_PIO_1,		0x0000020a,	0, },
+	{ XFER_PIO_2,		0x00000127,	0, },
+	{ XFER_PIO_3,		0x000000c6,	0, },
+	{ XFER_PIO_4,		0x00000065,	0, },
+	{ XFER_MW_DMA_0,	0x00084000,	0, },
+	{ XFER_MW_DMA_1,	0x00029800,	0, },
+	{ XFER_MW_DMA_2,	0x00019400,	0, },
+	{ XFER_UDMA_0,		0x19100000,	0, },
+	{ XFER_UDMA_1,		0x14d00000,	0, },
+	{ XFER_UDMA_2,		0x10900000,	0, },
+	{ XFER_UDMA_3,		0x0c700000,	0, },
+	{ XFER_UDMA_4,		0x0c500000,	0, },
+	{ -1, 0, 0 }
+};
+
+static const struct pata_macio_timing pata_macio_kauai_timings[] = {
+	{ XFER_PIO_0,		0x08000a92,	0, },
+	{ XFER_PIO_1,		0x0800060f,	0, },
+	{ XFER_PIO_2,		0x0800038b,	0, },
+	{ XFER_PIO_3,		0x05000249,	0, },
+	{ XFER_PIO_4,		0x04000148,	0, },
+	{ XFER_MW_DMA_0,	0x00618000,	0, },
+	{ XFER_MW_DMA_1,	0x00209000,	0, },
+	{ XFER_MW_DMA_2,	0x00148000,	0, },
+	{ XFER_UDMA_0,		         0,	0x000070c1, },
+	{ XFER_UDMA_1,		         0,	0x00005d81, },
+	{ XFER_UDMA_2,		         0,	0x00004a61, },
+	{ XFER_UDMA_3,		         0,	0x00003a51, },
+	{ XFER_UDMA_4,		         0,	0x00002a31, },
+	{ XFER_UDMA_5,		         0,	0x00002921, },
+	{ -1, 0, 0 }
+};
+
+static const struct pata_macio_timing pata_macio_shasta_timings[] = {
+	{ XFER_PIO_0,		0x0a000c97,	0, },
+	{ XFER_PIO_1,		0x07000712,	0, },
+	{ XFER_PIO_2,		0x040003cd,	0, },
+	{ XFER_PIO_3,		0x0500028b,	0, },
+	{ XFER_PIO_4,		0x0400010a,	0, },
+	{ XFER_MW_DMA_0,	0x00820800,	0, },
+	{ XFER_MW_DMA_1,	0x0028b000,	0, },
+	{ XFER_MW_DMA_2,	0x001ca000,	0, },
+	{ XFER_UDMA_0,		         0,	0x00035901, },
+	{ XFER_UDMA_1,		         0,	0x000348b1, },
+	{ XFER_UDMA_2,		         0,	0x00033881, },
+	{ XFER_UDMA_3,		         0,	0x00033861, },
+	{ XFER_UDMA_4,		         0,	0x00033841, },
+	{ XFER_UDMA_5,		         0,	0x00033031, },
+	{ XFER_UDMA_6,		         0,	0x00033021, },
+	{ -1, 0, 0 }
+};
+
+static const struct pata_macio_timing *pata_macio_find_timing(
+					    struct pata_macio_priv *priv,
+					    int mode)
+{
+	int i = 0;
+
+	while (priv->timings[i].mode > 0) {
+		if (priv->timings[i].mode == mode)
+			return &priv->timings[i];
+		i++;
+	}
+	return NULL;
+}
+
+
+static void pata_macio_apply_timings(struct ata_port *ap, unsigned int device)
+{
+	struct pata_macio_priv *priv = ap->private_data;
+	void __iomem *rbase = ap->ioaddr.cmd_addr;
+
+	if (priv->kind == controller_sh_ata6 ||
+	    priv->kind == controller_un_ata6 ||
+	    priv->kind == controller_k2_ata6) {
+		writel(priv->treg[device][0], rbase + IDE_KAUAI_PIO_CONFIG);
+		writel(priv->treg[device][1], rbase + IDE_KAUAI_ULTRA_CONFIG);
+	} else
+		writel(priv->treg[device][0], rbase + IDE_TIMING_CONFIG);
+}
+
+static void pata_macio_dev_select(struct ata_port *ap, unsigned int device)
+{
+	ata_sff_dev_select(ap, device);
+
+	/* Apply timings */
+	pata_macio_apply_timings(ap, device);
+}
+
+static void pata_macio_set_timings(struct ata_port *ap,
+				   struct ata_device *adev)
+{
+	struct pata_macio_priv *priv = ap->private_data;
+	const struct pata_macio_timing *t;
+
+	dev_dbg(priv->dev, "Set timings: DEV=%d,PIO=0x%x (%s),DMA=0x%x (%s)\n",
+		adev->devno,
+		adev->pio_mode,
+		ata_mode_string(ata_xfer_mode2mask(adev->pio_mode)),
+		adev->dma_mode,
+		ata_mode_string(ata_xfer_mode2mask(adev->dma_mode)));
+
+	/* First clear timings */
+	priv->treg[adev->devno][0] = priv->treg[adev->devno][1] = 0;
+
+	/* Now get the PIO timings */
+	t = pata_macio_find_timing(priv, adev->pio_mode);
+	if (t == NULL) {
+		dev_warn(priv->dev, "Invalid PIO timing requested: 0x%x\n",
+			 adev->pio_mode);
+		t = pata_macio_find_timing(priv, XFER_PIO_0);
+	}
+	BUG_ON(t == NULL);
+
+	/* PIO timings only ever use the first treg */
+	priv->treg[adev->devno][0] |= t->reg1;
+
+	/* Now get DMA timings */
+	t = pata_macio_find_timing(priv, adev->dma_mode);
+	if (t == NULL || (t->reg1 == 0 && t->reg2 == 0)) {
+		dev_dbg(priv->dev, "DMA timing not set yet, using MW_DMA_0\n");
+		t = pata_macio_find_timing(priv, XFER_MW_DMA_0);
+	}
+	BUG_ON(t == NULL);
+
+	/* DMA timings can use both tregs */
+	priv->treg[adev->devno][0] |= t->reg1;
+	priv->treg[adev->devno][1] |= t->reg2;
+
+	dev_dbg(priv->dev, " -> %08x %08x\n",
+		priv->treg[adev->devno][0],
+		priv->treg[adev->devno][1]);
+
+	/* Apply to hardware */
+	pata_macio_apply_timings(ap, adev->devno);
+}
+
+/*
+ * Blast some well known "safe" values to the timing registers at init or
+ * wakeup from sleep time, before we do real calculation
+ */
+static void pata_macio_default_timings(struct pata_macio_priv *priv)
+{
+	unsigned int value, value2 = 0;
+
+	switch(priv->kind) {
+		case controller_sh_ata6:
+			value = 0x0a820c97;
+			value2 = 0x00033031;
+			break;
+		case controller_un_ata6:
+		case controller_k2_ata6:
+			value = 0x08618a92;
+			value2 = 0x00002921;
+			break;
+		case controller_kl_ata4:
+			value = 0x0008438c;
+			break;
+		case controller_kl_ata3:
+			value = 0x00084526;
+			break;
+		case controller_heathrow:
+		case controller_ohare:
+		default:
+			value = 0x00074526;
+			break;
+	}
+	priv->treg[0][0] = priv->treg[1][0] = value;
+	priv->treg[0][1] = priv->treg[1][1] = value2;
+}
+
+static int pata_macio_cable_detect(struct ata_port *ap)
+{
+	struct pata_macio_priv *priv = ap->private_data;
+
+	return priv->cable_80 ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
+}
+
+static void pata_macio_qc_prep(struct ata_queued_cmd *qc)
+{
+	unsigned int write = (qc->tf.flags & ATA_TFLAG_WRITE);
+	struct ata_port *ap = qc->ap;
+	struct pata_macio_priv *priv = ap->private_data;
+	struct scatterlist *sg;
+	struct dbdma_cmd *table;
+	unsigned int si, pi;
+
+	dev_dbgdma(priv->dev, "%s: qc %p flags %lx, write %d dev %d\n",
+		   __func__, qc, qc->flags, write, qc->dev->devno);
+
+	if (!(qc->flags & ATA_QCFLAG_DMAMAP))
+		return;
+
+	table = (struct dbdma_cmd *) priv->dma_table_cpu;
+
+	pi = 0;
+	for_each_sg(qc->sg, sg, qc->n_elem, si) {
+		u32 addr, sg_len, len;
+
+		/* determine if physical DMA addr spans 64K boundary.
+		 * Note h/w doesn't support 64-bit, so we unconditionally
+		 * truncate dma_addr_t to u32.
+		 */
+		addr = (u32) sg_dma_address(sg);
+		sg_len = sg_dma_len(sg);
+
+		while (sg_len) {
+			/* table overflow should never happen */
+			BUG_ON (pi++ >= MAX_DCMDS);
+
+			len = (sg_len < MAX_DBDMA_SEG) ? sg_len : MAX_DBDMA_SEG;
+			st_le16(&table->command, write ? OUTPUT_MORE: INPUT_MORE);
+			st_le16(&table->req_count, len);
+			st_le32(&table->phy_addr, addr);
+			table->cmd_dep = 0;
+			table->xfer_status = 0;
+			table->res_count = 0;
+			addr += len;
+			sg_len -= len;
+			++table;
+		}
+	}
+
+	/* Should never happen according to Tejun */
+	BUG_ON(!pi);
+
+	/* Convert the last command to an input/output */
+	table--;
+	st_le16(&table->command, write ? OUTPUT_LAST: INPUT_LAST);
+	table++;
+
+	/* Add the stop command to the end of the list */
+	memset(table, 0, sizeof(struct dbdma_cmd));
+	st_le16(&table->command, DBDMA_STOP);
+
+	dev_dbgdma(priv->dev, "%s: %d DMA list entries\n", __func__, pi);
+}
+
+static void pata_macio_bmdma_setup(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct pata_macio_priv *priv = ap->private_data;
+	struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
+	int dev = qc->dev->devno;
+
+	dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc);
+
+	/* Make sure DMA commands updates are visible */
+	writel(priv->dma_table_dma, &dma_regs->cmdptr);
+
+	/* On KeyLargo 66Mhz cell, we need to add 60ns to wrDataSetup on
+	 * UDMA reads
+	 */
+	if (priv->kind == controller_kl_ata4 &&
+	    (priv->treg[dev][0] & TR_66_UDMA_EN)) {
+		void __iomem *rbase = ap->ioaddr.cmd_addr;
+		u32 reg = priv->treg[dev][0];
+
+		if (!(qc->tf.flags & ATA_TFLAG_WRITE))
+			reg += 0x00800000;
+		writel(reg, rbase + IDE_TIMING_CONFIG);
+	}
+
+	/* issue r/w command */
+	ap->ops->sff_exec_command(ap, &qc->tf);
+}
+
+static void pata_macio_bmdma_start(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct pata_macio_priv *priv = ap->private_data;
+	struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
+
+	dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc);
+
+	writel((RUN << 16) | RUN, &dma_regs->control);
+	/* Make sure it gets to the controller right now */
+	(void)readl(&dma_regs->control);
+}
+
+static void pata_macio_bmdma_stop(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct pata_macio_priv *priv = ap->private_data;
+	struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
+
+	dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc);
+
+	/* Stop the DMA engine and wait for it to full halt */
+	writel (((RUN|WAKE|DEAD) << 16), &dma_regs->control);
+	while (readl(&dma_regs->status) & RUN)
+		udelay(1);
+}
+
+static u8 pata_macio_bmdma_status(struct ata_port *ap)
+{
+	struct pata_macio_priv *priv = ap->private_data;
+	struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
+	u32 dstat, rstat = ATA_DMA_INTR;
+	unsigned long timeout = 0;
+
+	dstat = readl(&dma_regs->status);
+
+	dev_dbgdma(priv->dev, "%s: dstat=%x\n", __func__, dstat);
+
+	/* We have to things to deal with here:
+	 *
+	 * - The dbdma won't stop if the command was started
+	 * but completed with an error without transferring all
+	 * datas. This happens when bad blocks are met during
+	 * a multi-block transfer.
+	 *
+	 * - The dbdma fifo hasn't yet finished flushing to
+	 * to system memory when the disk interrupt occurs.
+	 *
+	 */
+
+	/* First check for errors */
+	if ((dstat & (RUN|DEAD)) != RUN)
+		rstat |= ATA_DMA_ERR;
+
+	/* If ACTIVE is cleared, the STOP command has been hit and
+	 * the transfer is complete. If not, we have to flush the
+	 * channel.
+	 */
+	if ((dstat & ACTIVE) == 0)
+		return rstat;
+
+	dev_dbgdma(priv->dev, "%s: DMA still active, flushing...\n", __func__);
+
+	/* If dbdma didn't execute the STOP command yet, the
+	 * active bit is still set. We consider that we aren't
+	 * sharing interrupts (which is hopefully the case with
+	 * those controllers) and so we just try to flush the
+	 * channel for pending data in the fifo
+	 */
+	udelay(1);
+	writel((FLUSH << 16) | FLUSH, &dma_regs->control);
+	for (;;) {
+		udelay(1);
+		dstat = readl(&dma_regs->status);
+		if ((dstat & FLUSH) == 0)
+			break;
+		if (++timeout > 1000) {
+			dev_warn(priv->dev, "timeout flushing DMA\n");
+			rstat |= ATA_DMA_ERR;
+			break;
+		}
+	}
+	return rstat;
+}
+
+/* port_start is when we allocate the DMA command list */
+static int pata_macio_port_start(struct ata_port *ap)
+{
+	struct pata_macio_priv *priv = ap->private_data;
+	struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
+
+	if (dma_regs == NULL)
+		return 0;
+
+	/* Make sure DMA controller is stopped */
+	writel((RUN|PAUSE|FLUSH|WAKE|DEAD) << 16, &dma_regs->control);
+	while (readl(&dma_regs->status) & RUN)
+		udelay(1);
+
+	/* Allocate space for the DBDMA commands.
+	 *
+	 * The +2 is +1 for the stop command and +1 to allow for
+	 * aligning the start address to a multiple of 16 bytes.
+	 */
+	priv->dma_table_cpu =
+		dmam_alloc_coherent(priv->dev,
+				    (MAX_DCMDS + 2) * sizeof(struct dbdma_cmd),
+				    &priv->dma_table_dma, GFP_KERNEL);
+	if (priv->dma_table_cpu == NULL) {
+		dev_err(priv->dev, "Unable to allocate DMA command list\n");
+		ap->ioaddr.bmdma_addr = NULL;
+	}
+	return 0;
+}
+
+static void pata_macio_irq_clear(struct ata_port *ap)
+{
+	struct pata_macio_priv *priv = ap->private_data;
+
+	/* Nothing to do here */
+
+	dev_dbgdma(priv->dev, "%s\n", __func__);
+}
+
+static void pata_macio_reset_hw(struct pata_macio_priv *priv, int resume)
+{
+	dev_dbg(priv->dev, "Enabling & resetting... \n");
+
+	if (priv->mediabay)
+		return;
+
+	if (priv->kind == controller_ohare && !resume) {
+		/* The code below is having trouble on some ohare machines
+		 * (timing related ?). Until I can put my hand on one of these
+		 * units, I keep the old way
+		 */
+		ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, priv->node, 0, 1);
+	} else {
+		int rc;
+
+ 		/* Reset and enable controller */
+		rc = ppc_md.feature_call(PMAC_FTR_IDE_RESET, priv->node, priv->aapl_bus_id, 1);
+		ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, priv->node, priv->aapl_bus_id, 1);
+		msleep(10);
+		/* Only bother waiting if there's a reset control */
+		if (rc == 0) {
+			ppc_md.feature_call(PMAC_FTR_IDE_RESET, priv->node, priv->aapl_bus_id, 0);
+			msleep(jiffies_to_msecs(IDE_WAKEUP_DELAY));
+		}
+	}
+
+	/* If resuming a PCI device, restore the config space here */
+	if (priv->pdev && resume) {
+		int rc;
+
+		pci_restore_state(priv->pdev);
+		rc = pcim_enable_device(priv->pdev);
+		if (rc)
+			dev_printk(KERN_ERR, &priv->pdev->dev,
+				   "Failed to enable device after resume (%d)\n", rc);
+		else
+			pci_set_master(priv->pdev);
+	}
+
+	/* On Kauai, initialize the FCR. We don't perform a reset, doesn't really
+	 * seem necessary and speeds up the boot process
+	 */
+	if (priv->kauai_fcr)
+		writel(KAUAI_FCR_UATA_MAGIC |
+		       KAUAI_FCR_UATA_RESET_N |
+		       KAUAI_FCR_UATA_ENABLE, priv->kauai_fcr);
+}
+
+/* Hook the standard slave config to fixup some HW related alignment
+ * restrictions
+ */
+static int pata_macio_slave_config(struct scsi_device *sdev)
+{
+	struct ata_port *ap = ata_shost_to_port(sdev->host);
+	struct pata_macio_priv *priv = ap->private_data;
+	struct ata_device *dev;
+	u16 cmd;
+	int rc;
+
+	/* First call original */
+	rc = ata_scsi_slave_config(sdev);
+	if (rc)
+		return rc;
+
+	/* This is lifted from sata_nv */
+	dev = &ap->link.device[sdev->id];
+
+	/* OHare has issues with non cache aligned DMA on some chipsets */
+	if (priv->kind == controller_ohare) {
+		blk_queue_update_dma_alignment(sdev->request_queue, 31);
+		blk_queue_update_dma_pad(sdev->request_queue, 31);
+
+		/* Tell the world about it */
+		ata_dev_printk(dev, KERN_INFO, "OHare alignment limits applied\n");
+		return 0;
+	}
+
+	/* We only have issues with ATAPI */
+	if (dev->class != ATA_DEV_ATAPI)
+		return 0;
+
+	/* Shasta and K2 seem to have "issues" with reads ... */
+	if (priv->kind == controller_sh_ata6 || priv->kind == controller_k2_ata6) {
+		/* Allright these are bad, apply restrictions */
+		blk_queue_update_dma_alignment(sdev->request_queue, 15);
+		blk_queue_update_dma_pad(sdev->request_queue, 15);
+
+		/* We enable MWI and hack cache line size directly here, this
+		 * is specific to this chipset and not normal values, we happen
+		 * to somewhat know what we are doing here (which is basically
+		 * to do the same Apple does and pray they did not get it wrong :-)
+		 */
+		BUG_ON(!priv->pdev);
+		pci_write_config_byte(priv->pdev, PCI_CACHE_LINE_SIZE, 0x08);
+		pci_read_config_word(priv->pdev, PCI_COMMAND, &cmd);
+		pci_write_config_word(priv->pdev, PCI_COMMAND,
+				      cmd | PCI_COMMAND_INVALIDATE);
+
+		/* Tell the world about it */
+		ata_dev_printk(dev, KERN_INFO, "K2/Shasta alignment limits applied\n");
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+
+static int pata_macio_do_suspend(struct pata_macio_priv *priv, pm_message_t mesg)
+{
+	int rc;
+
+	/* First, core libata suspend to do most of the work */
+	rc = ata_host_suspend(priv->host, mesg);
+	if (rc)
+		return rc;
+
+	/* Restore to default timings */
+	pata_macio_default_timings(priv);
+
+	/* Mask interrupt. Not strictly necessary but old driver did
+	 * it and I'd rather not change that here */
+	disable_irq(priv->irq);
+
+	/* The media bay will handle itself just fine */
+	if (priv->mediabay)
+		return 0;
+
+	/* Kauai has bus control FCRs directly here */
+	if (priv->kauai_fcr) {
+		u32 fcr = readl(priv->kauai_fcr);
+		fcr &= ~(KAUAI_FCR_UATA_RESET_N | KAUAI_FCR_UATA_ENABLE);
+		writel(fcr, priv->kauai_fcr);
+	}
+
+	/* For PCI, save state and disable DMA. No need to call
+	 * pci_set_power_state(), the HW doesn't do D states that
+	 * way, the platform code will take care of suspending the
+	 * ASIC properly
+	 */
+	if (priv->pdev) {
+		pci_save_state(priv->pdev);
+		pci_disable_device(priv->pdev);
+	}
+
+	/* Disable the bus on older machines and the cell on kauai */
+	ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, priv->node,
+			    priv->aapl_bus_id, 0);
+
+	return 0;
+}
+
+static int pata_macio_do_resume(struct pata_macio_priv *priv)
+{
+	/* Reset and re-enable the HW */
+	pata_macio_reset_hw(priv, 1);
+
+	/* Sanitize drive timings */
+	pata_macio_apply_timings(priv->host->ports[0], 0);
+
+	/* We want our IRQ back ! */
+	enable_irq(priv->irq);
+
+	/* Let the libata core take it from there */
+	ata_host_resume(priv->host);
+
+	return 0;
+}
+
+#endif /* CONFIG_PM */
+
+static struct scsi_host_template pata_macio_sht = {
+	ATA_BASE_SHT(DRV_NAME),
+	.sg_tablesize		= MAX_DCMDS,
+	.dma_boundary		= ATA_DMA_BOUNDARY,	/* We may not need that strict one */
+	.slave_configure	= pata_macio_slave_config,
+};
+
+static struct ata_port_operations pata_macio_ops = {
+	.inherits		= &ata_sff_port_ops,
+
+	.set_piomode		= pata_macio_set_timings,
+	.set_dmamode		= pata_macio_set_timings,
+	.cable_detect		= pata_macio_cable_detect,
+	.sff_dev_select		= pata_macio_dev_select,
+	.qc_prep		= pata_macio_qc_prep,
+	.mode_filter		= ata_bmdma_mode_filter,
+	.bmdma_setup		= pata_macio_bmdma_setup,
+	.bmdma_start		= pata_macio_bmdma_start,
+	.bmdma_stop		= pata_macio_bmdma_stop,
+	.bmdma_status		= pata_macio_bmdma_status,
+	.port_start		= pata_macio_port_start,
+	.sff_irq_clear		= pata_macio_irq_clear,
+};
+
+static void __devinit pata_macio_invariants(struct pata_macio_priv *priv)
+{
+	const int *bidp;
+
+	/* Identify the type of controller */
+	if (of_device_is_compatible(priv->node, "shasta-ata")) {
+		priv->kind = controller_sh_ata6;
+	        priv->timings = pata_macio_shasta_timings;
+	} else if (of_device_is_compatible(priv->node, "kauai-ata")) {
+		priv->kind = controller_un_ata6;
+	        priv->timings = pata_macio_kauai_timings;
+	} else if (of_device_is_compatible(priv->node, "K2-UATA")) {
+		priv->kind = controller_k2_ata6;
+	        priv->timings = pata_macio_kauai_timings;
+	} else if (of_device_is_compatible(priv->node, "keylargo-ata")) {
+		if (strcmp(priv->node->name, "ata-4") == 0) {
+			priv->kind = controller_kl_ata4;
+			priv->timings = pata_macio_kl66_timings;
+		} else {
+			priv->kind = controller_kl_ata3;
+			priv->timings = pata_macio_kl33_timings;
+		}
+	} else if (of_device_is_compatible(priv->node, "heathrow-ata")) {
+		priv->kind = controller_heathrow;
+		priv->timings = pata_macio_heathrow_timings;
+	} else {
+		priv->kind = controller_ohare;
+		priv->timings = pata_macio_ohare_timings;
+	}
+
+	/* XXX FIXME --- setup priv->mediabay here */
+
+	/* Get Apple bus ID (for clock and ASIC control) */
+	bidp = of_get_property(priv->node, "AAPL,bus-id", NULL);
+	priv->aapl_bus_id =  bidp ? *bidp : 0;
+
+	/* Fixup missing Apple bus ID in case of media-bay */
+	if (priv->mediabay && bidp == 0)
+		priv->aapl_bus_id = 1;
+
+	/* Get cable type from device-tree */
+	if (priv->kind == controller_kl_ata4 ||
+	    priv->kind == controller_un_ata6 ||
+	    priv->kind == controller_k2_ata6 ||
+	    priv->kind == controller_sh_ata6) {
+		const char* cable = of_get_property(priv->node, "cable-type",
+						    NULL);
+		if (cable && !strncmp(cable, "80-", 3))
+			priv->cable_80 = 1;
+	}
+
+	/* G5's seem to have incorrect cable type in device-tree.
+	 * Let's assume they always have a 80 conductor cable, this seem to
+	 * be always the case unless the user mucked around
+	 */
+	if (of_device_is_compatible(priv->node, "K2-UATA") ||
+	    of_device_is_compatible(priv->node, "shasta-ata"))
+		priv->cable_80 = 1;
+}
+
+static void __devinit pata_macio_setup_ios(struct ata_ioports *ioaddr,
+					   void __iomem * base,
+					   void __iomem * dma)
+{
+	/* cmd_addr is the base of regs for that port */
+	ioaddr->cmd_addr	= base;
+
+	/* taskfile registers */
+	ioaddr->data_addr	= base + (ATA_REG_DATA    << 4);
+	ioaddr->error_addr	= base + (ATA_REG_ERR     << 4);
+	ioaddr->feature_addr	= base + (ATA_REG_FEATURE << 4);
+	ioaddr->nsect_addr	= base + (ATA_REG_NSECT   << 4);
+	ioaddr->lbal_addr	= base + (ATA_REG_LBAL    << 4);
+	ioaddr->lbam_addr	= base + (ATA_REG_LBAM    << 4);
+	ioaddr->lbah_addr	= base + (ATA_REG_LBAH    << 4);
+	ioaddr->device_addr	= base + (ATA_REG_DEVICE  << 4);
+	ioaddr->status_addr	= base + (ATA_REG_STATUS  << 4);
+	ioaddr->command_addr	= base + (ATA_REG_CMD     << 4);
+	ioaddr->altstatus_addr	= base + 0x160;
+	ioaddr->ctl_addr	= base + 0x160;
+	ioaddr->bmdma_addr	= dma;
+}
+
+static void __devinit pmac_macio_calc_timing_masks(struct pata_macio_priv *priv,
+						   struct ata_port_info   *pinfo)
+{
+	int i = 0;
+
+	pinfo->pio_mask		= 0;
+	pinfo->mwdma_mask	= 0;
+	pinfo->udma_mask	= 0;
+
+	while (priv->timings[i].mode > 0) {
+		unsigned int mask = 1U << (priv->timings[i].mode & 0x0f);
+		switch(priv->timings[i].mode & 0xf0) {
+		case 0x00: /* PIO */
+			pinfo->pio_mask |= (mask >> 8);
+			break;
+		case 0x20: /* MWDMA */
+			pinfo->mwdma_mask |= mask;
+			break;
+		case 0x40: /* UDMA */
+			pinfo->udma_mask |= mask;
+			break;
+		}
+		i++;
+	}
+	dev_dbg(priv->dev, "Supported masks: PIO=%lx, MWDMA=%lx, UDMA=%lx\n",
+		pinfo->pio_mask, pinfo->mwdma_mask, pinfo->udma_mask);
+}
+
+static int __devinit pata_macio_common_init(struct pata_macio_priv	*priv,
+					    resource_size_t		tfregs,
+					    resource_size_t		dmaregs,
+					    resource_size_t		fcregs,
+					    unsigned long		irq)
+{
+	struct ata_port_info		pinfo;
+	const struct ata_port_info	*ppi[] = { &pinfo, NULL };
+	void __iomem			*dma_regs = NULL;
+	int				rc;
+
+	/* Fill up privates with various invariants collected from the
+	 * device-tree
+	 */
+	pata_macio_invariants(priv);
+
+	/* Make sure we have sane initial timings in the cache */
+	pata_macio_default_timings(priv);
+
+	/* Not sure what the real max is but we know it's less than 64K, let's
+	 * use 64K minus 256
+	 */
+	dma_set_max_seg_size(priv->dev, MAX_DBDMA_SEG);
+
+	/* Allocate libata host for 1 port */
+	memset(&pinfo, 0, sizeof(struct ata_port_info));
+	pmac_macio_calc_timing_masks(priv, &pinfo);
+	pinfo.flags		= ATA_FLAG_SLAVE_POSS | ATA_FLAG_MMIO |
+				  ATA_FLAG_NO_LEGACY;
+	pinfo.port_ops		= &pata_macio_ops;
+	pinfo.private_data	= priv;
+
+	priv->host = ata_host_alloc_pinfo(priv->dev, ppi, 1);
+	if (priv->host == NULL) {
+		dev_err(priv->dev, "Failed to allocate ATA port structure\n");
+		return -ENOMEM;
+	}
+
+	lock_media_bay(priv->mdev->media_bay);
+
+	/* Setup the private data in host too */
+	priv->host->private_data = priv;
+
+	/* Map base registers */
+	priv->tfregs = devm_ioremap(priv->dev, tfregs, 0x100);
+	if (priv->tfregs == NULL) {
+		dev_err(priv->dev, "Failed to map ATA ports\n");
+		unlock_media_bay(priv->mdev->media_bay);
+		return -ENOMEM;
+	}
+	priv->host->iomap = &priv->tfregs;
+
+	/* Map DMA regs */
+	if (dmaregs != 0) {
+		dma_regs = devm_ioremap(priv->dev, dmaregs,
+					sizeof(struct dbdma_regs));
+		if (dma_regs == NULL)
+			dev_warn(priv->dev, "Failed to map ATA DMA registers\n");
+	}
+
+	/* If chip has local feature control, map those regs too */
+	if (fcregs != 0) {
+		priv->kauai_fcr = devm_ioremap(priv->dev, fcregs, 4);
+		if (priv->kauai_fcr == NULL) {
+			dev_err(priv->dev, "Failed to map ATA FCR register\n");
+			unlock_media_bay(priv->mdev->media_bay);
+			return -ENOMEM;
+		}
+	}
+
+	/* Setup port data structure */
+	pata_macio_setup_ios(&priv->host->ports[0]->ioaddr,
+			     priv->tfregs, dma_regs);
+	priv->host->ports[0]->private_data = priv;
+
+	/* hard-reset the controller */
+	pata_macio_reset_hw(priv, 0);
+	pata_macio_apply_timings(priv->host->ports[0], 0);
+
+	/* Enable bus master if necessary */
+	if (priv->pdev && dma_regs)
+		pci_set_master(priv->pdev);
+
+	dev_info(priv->dev, "Activating pata-macio chipset %s, Apple bus ID %d\n",
+		 macio_ata_names[priv->kind], priv->aapl_bus_id);
+
+	/* Start it up */
+	priv->irq = irq;
+	rc = ata_host_activate(priv->host, irq, ata_sff_interrupt, 0,
+			       &pata_macio_sht);
+	unlock_media_bay(priv->mdev->media_bay);
+	return rc;
+}
+
+static int __devinit pata_macio_attach(struct macio_dev *mdev,
+				       const struct of_device_id *match)
+{
+	struct pata_macio_priv	*priv;
+	resource_size_t		tfregs, dmaregs = 0;
+	unsigned long		irq;
+
+	/* Check for broken device-trees */
+	if (macio_resource_count(mdev) == 0) {
+		dev_err(&mdev->ofdev.dev,
+			"No addresses for controller\n");
+		return -ENXIO;
+	}
+
+	/* Enable managed resources */
+	macio_enable_devres(mdev);
+
+	/* Allocate and init private data structure */
+	priv = devm_kzalloc(&mdev->ofdev.dev,
+			    sizeof(struct pata_macio_priv), GFP_KERNEL);
+	if (priv == NULL) {
+		dev_err(&mdev->ofdev.dev,
+			"Failed to allocate private memory\n");
+		return -ENOMEM;
+	}
+	priv->node = of_node_get(mdev->ofdev.node);
+	priv->mdev = mdev;
+	priv->dev = &mdev->ofdev.dev;
+
+	/* Request memory resource for taskfile registers */
+	if (macio_request_resource(mdev, 0, "pata-macio")) {
+		dev_err(&mdev->ofdev.dev,
+			"Cannot obtain taskfile resource\n");
+		return -EBUSY;
+	}
+	tfregs = macio_resource_start(mdev, 0);
+
+	/* Request resources for DMA registers if any */
+	if (macio_resource_count(mdev) >= 2) {
+		if (macio_request_resource(mdev, 1, "pata-macio-dma"))
+			dev_err(&mdev->ofdev.dev,
+				"Cannot obtain DMA resource\n");
+		else
+			dmaregs = macio_resource_start(mdev, 1);
+	}
+
+	/*
+	 * Fixup missing IRQ for some old implementations with broken
+	 * device-trees.
+	 *
+	 * This is a bit bogus, it should be fixed in the device-tree itself,
+	 * via the existing macio fixups, based on the type of interrupt
+	 * controller in the machine. However, I have no test HW for this case,
+	 * and this trick works well enough on those old machines...
+	 */
+	if (macio_irq_count(mdev) == 0) {
+		dev_warn(&mdev->ofdev.dev,
+			 "No interrupts for controller, using 13\n");
+		irq = irq_create_mapping(NULL, 13);
+	} else
+		irq = macio_irq(mdev, 0);
+
+	/* Get register addresses and call common initialization */
+	if (pata_macio_common_init(priv,
+				   tfregs,		/* Taskfile regs */
+				   dmaregs,		/* DBDMA regs */
+				   0,			/* Feature control */
+				   irq))
+		return -ENXIO;
+
+	return 0;
+}
+
+static int __devexit pata_macio_detach(struct macio_dev *mdev)
+{
+	struct ata_host *host = macio_get_drvdata(mdev);
+
+	ata_host_detach(host);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+
+static int pata_macio_suspend(struct macio_dev *mdev, pm_message_t mesg)
+{
+	struct ata_host *host = macio_get_drvdata(mdev);
+
+	return pata_macio_do_suspend(host->private_data, mesg);
+}
+
+static int pata_macio_resume(struct macio_dev *mdev)
+{
+	struct ata_host *host = macio_get_drvdata(mdev);
+
+	return pata_macio_do_resume(host->private_data);
+}
+
+#endif /* CONFIG_PM */
+
+#ifdef CONFIG_PMAC_MEDIABAY
+static void pata_macio_mb_event(struct macio_dev* mdev, int mb_state)
+{
+	struct ata_host *host = macio_get_drvdata(mdev);
+	struct ata_port *ap;
+	struct ata_eh_info *ehi;
+	struct ata_device *dev;
+	unsigned long flags;
+
+	if (!host)
+		return;
+	ap = host->ports[0];
+	spin_lock_irqsave(ap->lock, flags);
+	ehi = &ap->link.eh_info;
+	if (mb_state == MB_CD) {
+		ata_ehi_push_desc(ehi, "mediabay plug");
+		ata_ehi_hotplugged(ehi);
+		ata_port_freeze(ap);
+	} else {
+		ata_ehi_push_desc(ehi, "mediabay unplug");
+		ata_for_each_dev(dev, &ap->link, ALL)
+			dev->flags |= ATA_DFLAG_DETACH;
+		ata_port_schedule_eh(ap);
+	}
+	spin_unlock_irqrestore(ap->lock, flags);
+
+}
+#endif /* CONFIG_PMAC_MEDIABAY */
+
+
+static int __devinit pata_macio_pci_attach(struct pci_dev *pdev,
+					   const struct pci_device_id *id)
+{
+	struct pata_macio_priv	*priv;
+	struct device_node	*np;
+	resource_size_t		rbase;
+
+	/* We cannot use a MacIO controller without its OF device node */
+	np = pci_device_to_OF_node(pdev);
+	if (np == NULL) {
+		dev_err(&pdev->dev,
+			"Cannot find OF device node for controller\n");
+		return -ENODEV;
+	}
+
+	/* Check that it can be enabled */
+	if (pcim_enable_device(pdev)) {
+		dev_err(&pdev->dev,
+			"Cannot enable controller PCI device\n");
+		return -ENXIO;
+	}
+
+	/* Allocate and init private data structure */
+	priv = devm_kzalloc(&pdev->dev,
+			    sizeof(struct pata_macio_priv), GFP_KERNEL);
+	if (priv == NULL) {
+		dev_err(&pdev->dev,
+			"Failed to allocate private memory\n");
+		return -ENOMEM;
+	}
+	priv->node = of_node_get(np);
+	priv->pdev = pdev;
+	priv->dev = &pdev->dev;
+
+	/* Get MMIO regions */
+	if (pci_request_regions(pdev, "pata-macio")) {
+		dev_err(&pdev->dev,
+			"Cannot obtain PCI resources\n");
+		return -EBUSY;
+	}
+
+	/* Get register addresses and call common initialization */
+	rbase = pci_resource_start(pdev, 0);
+	if (pata_macio_common_init(priv,
+				   rbase + 0x2000,	/* Taskfile regs */
+				   rbase + 0x1000,	/* DBDMA regs */
+				   rbase,		/* Feature control */
+				   pdev->irq))
+		return -ENXIO;
+
+	return 0;
+}
+
+static void __devexit pata_macio_pci_detach(struct pci_dev *pdev)
+{
+	struct ata_host *host = dev_get_drvdata(&pdev->dev);
+
+	ata_host_detach(host);
+}
+
+#ifdef CONFIG_PM
+
+static int pata_macio_pci_suspend(struct pci_dev *pdev, pm_message_t mesg)
+{
+	struct ata_host *host = dev_get_drvdata(&pdev->dev);
+
+	return pata_macio_do_suspend(host->private_data, mesg);
+}
+
+static int pata_macio_pci_resume(struct pci_dev *pdev)
+{
+	struct ata_host *host = dev_get_drvdata(&pdev->dev);
+
+	return pata_macio_do_resume(host->private_data);
+}
+
+#endif /* CONFIG_PM */
+
+static struct of_device_id pata_macio_match[] =
+{
+	{
+	.name 		= "IDE",
+	},
+	{
+	.name 		= "ATA",
+	},
+	{
+	.type		= "ide",
+	},
+	{
+	.type		= "ata",
+	},
+	{},
+};
+
+static struct macio_driver pata_macio_driver =
+{
+	.name 		= "pata-macio",
+	.match_table	= pata_macio_match,
+	.probe		= pata_macio_attach,
+	.remove		= pata_macio_detach,
+#ifdef CONFIG_PM
+	.suspend	= pata_macio_suspend,
+	.resume		= pata_macio_resume,
+#endif
+#ifdef CONFIG_PMAC_MEDIABAY
+	.mediabay_event	= pata_macio_mb_event,
+#endif
+	.driver = {
+		.owner		= THIS_MODULE,
+	},
+};
+
+static const struct pci_device_id pata_macio_pci_match[] = {
+	{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_UNI_N_ATA),	0 },
+	{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_IPID_ATA100),	0 },
+	{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_K2_ATA100),	0 },
+	{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_SH_ATA),	0 },
+	{ PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_IPID2_ATA),	0 },
+	{},
+};
+
+static struct pci_driver pata_macio_pci_driver = {
+	.name		= "pata-pci-macio",
+	.id_table	= pata_macio_pci_match,
+	.probe		= pata_macio_pci_attach,
+	.remove		= pata_macio_pci_detach,
+#ifdef CONFIG_PM
+	.suspend	= pata_macio_pci_suspend,
+	.resume		= pata_macio_pci_resume,
+#endif
+	.driver = {
+		.owner		= THIS_MODULE,
+	},
+};
+MODULE_DEVICE_TABLE(pci, pata_macio_pci_match);
+
+
+static int __init pata_macio_init(void)
+{
+	int rc;
+
+	if (!machine_is(powermac))
+		return -ENODEV;
+
+	rc = pci_register_driver(&pata_macio_pci_driver);
+	if (rc)
+		return rc;
+	rc = macio_register_driver(&pata_macio_driver);
+	if (rc) {
+		pci_unregister_driver(&pata_macio_pci_driver);
+		return rc;
+	}
+	return 0;
+}
+
+static void __exit pata_macio_exit(void)
+{
+	macio_unregister_driver(&pata_macio_driver);
+	pci_unregister_driver(&pata_macio_pci_driver);
+}
+
+module_init(pata_macio_init);
+module_exit(pata_macio_exit);
+
+MODULE_AUTHOR("Benjamin Herrenschmidt");
+MODULE_DESCRIPTION("Apple MacIO PATA driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
Index: linux-work/drivers/ata/Kconfig
===================================================================
--- linux-work.orig/drivers/ata/Kconfig	2009-12-01 17:48:27.000000000 +1100
+++ linux-work/drivers/ata/Kconfig	2009-12-01 17:48:48.000000000 +1100
@@ -781,5 +781,15 @@  config PATA_BF54X
 
 	  If unsure, say N.
 
+config PATA_MACIO
+	tristate "Apple PowerMac/PowerBook internal 'MacIO' IDE"
+	depends on PPC_PMAC
+	help
+	  Most IDE capable PowerMacs have IDE busses driven by a variant
+          of this controller which is part of the Apple chipset used on
+          most PowerMac models. Some models have multiple busses using
+          different chipsets, though generally, MacIO is one of them.
+
+
 endif # ATA_SFF
 endif # ATA
Index: linux-work/drivers/ata/Makefile
===================================================================
--- linux-work.orig/drivers/ata/Makefile	2009-12-01 17:48:27.000000000 +1100
+++ linux-work/drivers/ata/Makefile	2009-12-01 17:48:48.000000000 +1100
@@ -18,6 +18,7 @@  obj-$(CONFIG_SATA_MV)		+= sata_mv.o
 obj-$(CONFIG_SATA_INIC162X)	+= sata_inic162x.o
 obj-$(CONFIG_PDC_ADMA)		+= pdc_adma.o
 obj-$(CONFIG_SATA_FSL)		+= sata_fsl.o
+obj-$(CONFIG_PATA_MACIO)	+= pata_macio.o
 
 obj-$(CONFIG_PATA_ALI)		+= pata_ali.o
 obj-$(CONFIG_PATA_AMD)		+= pata_amd.o