@@ -5,32 +5,48 @@ which provides a synchronous audio interface that supports fullduplex
serial interfaces with frame synchronization such as I2S, AC97, TDM, and
codec/DSP interfaces.
-
Required properties:
-- compatible: Compatible list, contains "fsl,vf610-sai" or "fsl,imx6sx-sai".
-- reg: Offset and length of the register set for the device.
-- clocks: Must contain an entry for each entry in clock-names.
-- clock-names : Must include the "bus" for register access and "mclk1" "mclk2"
- "mclk3" for bit clock and frame clock providing.
-- dmas : Generic dma devicetree binding as described in
- Documentation/devicetree/bindings/dma/dma.txt.
-- dma-names : Two dmas have to be defined, "tx" and "rx".
-- pinctrl-names: Must contain a "default" entry.
-- pinctrl-NNN: One property must exist for each entry in pinctrl-names.
- See ../pinctrl/pinctrl-bindings.txt for details of the property values.
-- big-endian: Boolean property, required if all the FTM_PWM registers
- are big-endian rather than little-endian.
-- lsb-first: Configures whether the LSB or the MSB is transmitted first for
- the fifo data. If this property is absent, the MSB is transmitted first as
- default, or the LSB is transmitted first.
-- fsl,sai-synchronous-rx: This is a boolean property. If present, indicating
- that SAI will work in the synchronous mode (sync Tx with Rx) which means
- both the transimitter and receiver will send and receive data by following
- receiver's bit clocks and frame sync clocks.
-- fsl,sai-asynchronous: This is a boolean property. If present, indicating
- that SAI will work in the asynchronous mode, which means both transimitter
- and receiver will send and receive data by following their own bit clocks
- and frame sync clocks separately.
+
+ - compatible : Compatible list, contains "fsl,vf610-sai" or
+ "fsl,imx6sx-sai".
+
+ - reg : Offset and length of the register set for the device.
+
+ - clocks : Must contain an entry for each entry in clock-names.
+
+ - clock-names : Must include the "bus" for register access and
+ "mclk1", "mclk2", "mclk3" for bit clock and frame
+ clock providing.
+ - dmas : Generic dma devicetree binding as described in
+ Documentation/devicetree/bindings/dma/dma.txt.
+
+ - dma-names : Two dmas have to be defined, "tx" and "rx".
+
+ - pinctrl-names : Must contain a "default" entry.
+
+ - pinctrl-NNN : One property must exist for each entry in
+ pinctrl-names. See ../pinctrl/pinctrl-bindings.txt
+ for details of the property values.
+
+ - big-endian : Boolean property, required if all the FTM_PWM
+ registers are big-endian rather than little-endian.
+
+ - lsb-first : Configures whether the LSB or the MSB is transmitted
+ first for the fifo data. If this property is absent,
+ the MSB is transmitted first as default, or the LSB
+ is transmitted first.
+
+ - fsl,sai-synchronous-rx: This is a boolean property. If present, indicating
+ that SAI will work in the synchronous mode (sync Tx
+ with Rx) which means both the transimitter and the
+ receiver will send and receive data by following
+ receiver's bit clocks and frame sync clocks.
+
+ - fsl,sai-asynchronous: This is a boolean property. If present, indicating
+ that SAI will work in the asynchronous mode, which
+ means both transimitter and receiver will send and
+ receive data by following their own bit clocks and
+ frame sync clocks separately.
Note:
- If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the
This patch refines the DT binding doc for more readability by adding extra blank lines and indentations. Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com> --- .../devicetree/bindings/sound/fsl-sai.txt | 66 ++++++++++++++-------- 1 file changed, 41 insertions(+), 25 deletions(-)