diff mbox

[U-Boot,3/3] ARM: atmel: add sama5d4ek board support

Message ID 1410854244-30424-4-git-send-email-voice.shen@atmel.com
State Changes Requested, archived
Delegated to: Andreas Bießmann
Headers show

Commit Message

Bo Shen Sept. 16, 2014, 7:57 a.m. UTC 
The code for this board supports following features:
  - Boot media support: NAND flash/SD card/SPI flash
  - Support LCD display
  - Support ethernet
  - Support USB mass storage

Signed-off-by: Bo Shen <voice.shen@atmel.com>
---

 arch/arm/Kconfig                          |   4 +
 arch/arm/cpu/armv7/at91/timer.c           |   3 +-
 arch/arm/include/asm/arch-at91/at91_pmc.h |   6 +-
 arch/arm/include/asm/arch-at91/clk.h      |  29 +++
 arch/arm/include/asm/arch-at91/hardware.h |   2 +
 arch/arm/include/asm/arch-at91/sama5d4.h  | 199 ++++++++++++++++++
 board/atmel/sama5d4ek/Kconfig             |  18 ++
 board/atmel/sama5d4ek/MAINTAINERS         |   8 +
 board/atmel/sama5d4ek/Makefile            |  15 ++
 board/atmel/sama5d4ek/sama5d4ek.c         | 322 ++++++++++++++++++++++++++++++
 configs/sama5d4ek_mmc_defconfig           |   3 +
 configs/sama5d4ek_nandflash_defconfig     |   3 +
 configs/sama5d4ek_spiflash_defconfig      |   3 +
 include/configs/sama5d4ek.h               | 215 ++++++++++++++++++++
 14 files changed, 826 insertions(+), 4 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-at91/sama5d4.h
 create mode 100644 board/atmel/sama5d4ek/Kconfig
 create mode 100644 board/atmel/sama5d4ek/MAINTAINERS
 create mode 100644 board/atmel/sama5d4ek/Makefile
 create mode 100644 board/atmel/sama5d4ek/sama5d4ek.c
 create mode 100644 configs/sama5d4ek_mmc_defconfig
 create mode 100644 configs/sama5d4ek_nandflash_defconfig
 create mode 100644 configs/sama5d4ek_spiflash_defconfig
 create mode 100644 include/configs/sama5d4ek.h

Comments

Andreas Bießmann Oct. 25, 2014, 12:26 a.m. UTC | #1 
Hi Bo,

On 16.09.14 09:57, Bo Shen wrote:
> The code for this board supports following features:
>   - Boot media support: NAND flash/SD card/SPI flash
>   - Support LCD display
>   - Support ethernet
>   - Support USB mass storage
> 
> Signed-off-by: Bo Shen <voice.shen@atmel.com>
> ---
> 
>  arch/arm/Kconfig                          |   4 +
>  arch/arm/cpu/armv7/at91/timer.c           |   3 +-
>  arch/arm/include/asm/arch-at91/at91_pmc.h |   6 +-
>  arch/arm/include/asm/arch-at91/clk.h      |  29 +++
>  arch/arm/include/asm/arch-at91/hardware.h |   2 +
>  arch/arm/include/asm/arch-at91/sama5d4.h  | 199 ++++++++++++++++++
>  board/atmel/sama5d4ek/Kconfig             |  18 ++
>  board/atmel/sama5d4ek/MAINTAINERS         |   8 +
>  board/atmel/sama5d4ek/Makefile            |  15 ++
>  board/atmel/sama5d4ek/sama5d4ek.c         | 322 ++++++++++++++++++++++++++++++
>  configs/sama5d4ek_mmc_defconfig           |   3 +
>  configs/sama5d4ek_nandflash_defconfig     |   3 +
>  configs/sama5d4ek_spiflash_defconfig      |   3 +
>  include/configs/sama5d4ek.h               | 215 ++++++++++++++++++++
>  14 files changed, 826 insertions(+), 4 deletions(-)
>  create mode 100644 arch/arm/include/asm/arch-at91/sama5d4.h
>  create mode 100644 board/atmel/sama5d4ek/Kconfig
>  create mode 100644 board/atmel/sama5d4ek/MAINTAINERS
>  create mode 100644 board/atmel/sama5d4ek/Makefile
>  create mode 100644 board/atmel/sama5d4ek/sama5d4ek.c
>  create mode 100644 configs/sama5d4ek_mmc_defconfig
>  create mode 100644 configs/sama5d4ek_nandflash_defconfig
>  create mode 100644 configs/sama5d4ek_spiflash_defconfig
>  create mode 100644 include/configs/sama5d4ek.h
> 
> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> index c8537bb..bbccd46 100644
> --- a/arch/arm/Kconfig
> +++ b/arch/arm/Kconfig
> @@ -321,6 +321,9 @@ config TARGET_SAMA5D3_XPLAINED
>  config TARGET_SAMA5D3XEK
>  	bool "Support sama5d3xek"
>  
> +config TARGET_SAMA5D4EK
> +	bool "Support sama5d4ek"
> +
>  config TARGET_BCM28155_AP
>  	bool "Support bcm28155_ap"
>  
> @@ -569,6 +572,7 @@ source "board/atmel/at91sam9rlek/Kconfig"
>  source "board/atmel/at91sam9x5ek/Kconfig"
>  source "board/atmel/sama5d3_xplained/Kconfig"
>  source "board/atmel/sama5d3xek/Kconfig"
> +source "board/atmel/sama5d4ek/Kconfig"
>  source "board/balloon3/Kconfig"
>  source "board/barco/titanium/Kconfig"
>  source "board/bluegiga/apx4devkit/Kconfig"
> diff --git a/arch/arm/cpu/armv7/at91/timer.c b/arch/arm/cpu/armv7/at91/timer.c
> index e3ebfe0..19bf80b 100644
> --- a/arch/arm/cpu/armv7/at91/timer.c
> +++ b/arch/arm/cpu/armv7/at91/timer.c
> @@ -65,7 +65,8 @@ int timer_init(void)
>  	/* Enable PITC */
>  	writel(TIMER_LOAD_VAL | AT91_PIT_MR_EN , &pit->mr);
>  
> -	gd->arch.timer_rate_hz = gd->arch.mck_rate_hz / 16;
> +	gd->arch.timer_rate_hz = get_pit_clk_rate() / 16;
> +

is this part related to sama5d4ek or is it a generic fix? Could yopu
please send as an extra patch if it's the latter?

>  	gd->arch.tbu = 0;
>  	gd->arch.tbl = 0;
>  
> diff --git a/arch/arm/include/asm/arch-at91/at91_pmc.h b/arch/arm/include/asm/arch-at91/at91_pmc.h
> index 27331ff..e81ece9 100644
> --- a/arch/arm/include/asm/arch-at91/at91_pmc.h
> +++ b/arch/arm/include/asm/arch-at91/at91_pmc.h
> @@ -78,7 +78,7 @@ typedef struct at91_pmc {
>  #define AT91_PMC_PLLXR_DIV(x)		(x & 0xFF)
>  #define AT91_PMC_PLLXR_PLLCOUNT(x)	((x & 0x3F) << 8)
>  #define AT91_PMC_PLLXR_OUT(x)		((x & 0x03) << 14)
> -#ifdef CONFIG_SAMA5D3
> +#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
>  #define AT91_PMC_PLLXR_MUL(x)		((x & 0x7F) << 18)
>  #else
>  #define AT91_PMC_PLLXR_MUL(x)		((x & 0x7FF) << 16)
> @@ -97,7 +97,7 @@ typedef struct at91_pmc {
>  #define AT91_PMC_MCKR_CSS_PLLB		0x00000003
>  #define AT91_PMC_MCKR_CSS_MASK		0x00000003
>  
> -#ifdef CONFIG_SAMA5D3
> +#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
>  #define AT91_PMC_MCKR_PRES_1		0x00000000
>  #define AT91_PMC_MCKR_PRES_2		0x00000010
>  #define AT91_PMC_MCKR_PRES_4		0x00000020
> @@ -126,7 +126,7 @@ typedef struct at91_pmc {
>  #else
>  #define AT91_PMC_MCKR_MDIV_1		0x00000000
>  #define AT91_PMC_MCKR_MDIV_2		0x00000100
> -#ifdef CONFIG_SAMA5D3
> +#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
>  #define AT91_PMC_MCKR_MDIV_3		0x00000300
>  #endif
>  #define AT91_PMC_MCKR_MDIV_4		0x00000200
> diff --git a/arch/arm/include/asm/arch-at91/clk.h b/arch/arm/include/asm/arch-at91/clk.h
> index 4076a78..7615018 100644
> --- a/arch/arm/include/asm/arch-at91/clk.h
> +++ b/arch/arm/include/asm/arch-at91/clk.h
> @@ -50,12 +50,20 @@ static inline u32 get_pllb_init(void)
>  
>  static inline unsigned long get_macb_pclk_rate(unsigned int dev_id)
>  {
> +#ifdef CPU_HAS_H32MXDIV
> +	return get_mck_clk_rate() / H32MXDIV;
> +#else

I wonder if we should introduce H32MXDIV for all atmel SoC and remove
the CPU_HAS_H32MXDIV here. A division by 1 should be optimized away if
it is a constant. After all this piece of code would be more readable.

>  	return get_mck_clk_rate();
> +#endif
>  }
>  
>  static inline unsigned long get_usart_clk_rate(unsigned int dev_id)
>  {
> +#ifdef CPU_HAS_H32MXDIV
> +	return get_mck_clk_rate() / H32MXDIV;
> +#else
>  	return get_mck_clk_rate();
> +#endif
>  }
>  
>  static inline unsigned long get_lcdc_clk_rate(unsigned int dev_id)
> @@ -65,17 +73,38 @@ static inline unsigned long get_lcdc_clk_rate(unsigned int dev_id)
>  
>  static inline unsigned long get_spi_clk_rate(unsigned int dev_id)
>  {
> +#ifdef CPU_HAS_H32MXDIV
> +	return get_mck_clk_rate() / H32MXDIV;
> +#else
>  	return get_mck_clk_rate();
> +#endif
>  }
>  
>  static inline unsigned long get_twi_clk_rate(unsigned int dev_id)
>  {
> +#ifdef CPU_HAS_H32MXDIV
> +	return get_mck_clk_rate() / H32MXDIV;
> +#else
>  	return get_mck_clk_rate();
> +#endif
>  }
>  
>  static inline unsigned long get_mci_clk_rate(void)
>  {
> +#ifdef CPU_HAS_H32MXDIV
> +	return get_mck_clk_rate() / H32MXDIV;
> +#else
>  	return get_mck_clk_rate();
> +#endif
> +}
> +
> +static inline unsigned long get_pit_clk_rate(void)
> +{
> +#ifdef CPU_HAS_H32MXDIV
> +	return get_mck_clk_rate() / H32MXDIV;
> +#else
> +	return get_mck_clk_rate();
> +#endif
>  }
>  
>  int at91_clock_init(unsigned long main_clock);
> diff --git a/arch/arm/include/asm/arch-at91/hardware.h b/arch/arm/include/asm/arch-at91/hardware.h
> index d712a0d..bf0a1bd 100644
> --- a/arch/arm/include/asm/arch-at91/hardware.h
> +++ b/arch/arm/include/asm/arch-at91/hardware.h
> @@ -27,6 +27,8 @@
>  # include <asm/arch/at91cap9.h>
>  #elif defined(CONFIG_SAMA5D3)
>  # include <asm/arch/sama5d3.h>
> +#elif defined(CONFIG_SAMA5D4)
> +# include <asm/arch/sama5d4.h>
>  #else
>  # error "Unsupported AT91 processor"
>  #endif
> diff --git a/arch/arm/include/asm/arch-at91/sama5d4.h b/arch/arm/include/asm/arch-at91/sama5d4.h
> new file mode 100644
> index 0000000..12a6646
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-at91/sama5d4.h
> @@ -0,0 +1,199 @@
> +/*
> + * Chip-specific header file for the SAMA5D4 SoC
> + *
> + * Copyright (C) 2014 Atmel
> + *		      Bo Shen <voice.shen@atmel.com>
> + *
> + * SPDX-License-Identifier:     GPL-2.0+
> + */
> +
> +#ifndef __SAMA5D4_H
> +#define __SAMA5D4_H
> +
> +/*
> + * defines to be used in other places
> + */
> +#define CONFIG_ARMV7		/* ARM Cortex-A5 Core */
> +#define CONFIG_AT91FAMILY	/* It's a member of AT91 */

We should start moving these defines into Kconfig ... someday

> +
> +/*
> + * Peripheral identifiers/interrupts.
> + */
> +#define ATMEL_ID_FIQ	0	/* FIQ Interrupt */
> +#define ATMEL_ID_SYS	1	/* System Controller */
> +#define ATMEL_ID_ARM	2	/* Performance Monitor Unit */
> +#define ATMEL_ID_PIT	3	/* Periodic Interval Timer */
> +#define ATMEL_ID_WDT	4	/* Watchdog timer */
> +#define ATMEL_ID_PIOD	5	/* Parallel I/O Controller D */
> +#define ATMEL_ID_USART0	6	/* USART 0 */
> +#define ATMEL_ID_USART1	7	/* USART 1 */
> +#define ATMEL_ID_DMA0	8	/* DMA Controller 0 */
> +#define ATMEL_ID_ICM	9	/* Integrity Check Monitor */
> +#define ATMEL_ID_PKCC	10	/* Public Key Crypto Controller */
> +#define ATMEL_ID_AES	12	/* Advanced Encryption Standard */
> +#define ATMEL_ID_AESB	13	/* AES Bridge*/
> +#define ATMEL_ID_TDES	14	/* Triple Data Encryption Standard */
> +#define ATMEL_ID_SHA    15	/* SHA Signature */
> +#define ATMEL_ID_MPDDRC	16	/* MPDDR controller */
> +#define ATMEL_ID_MATRIX1	17	/* H32MX, 32-bit AHB Matrix */
> +#define ATMEL_ID_MATRIX0	18	/* H64MX, 64-bit AHB Matrix */
> +#define ATMEL_ID_VDEC	19	/* Video Decoder */
> +#define ATMEL_ID_SBM	20	/* Secure Box Module */
> +#define ATMEL_ID_SMC	22	/* Multi-bit ECC interrupt */
> +#define ATMEL_ID_PIOA	23	/* Parallel I/O Controller A */
> +#define ATMEL_ID_PIOB	24	/* Parallel I/O Controller B */
> +#define ATMEL_ID_PIOC	25	/* Parallel I/O Controller C */
> +#define ATMEL_ID_PIOE	26	/* Parallel I/O Controller E */
> +#define ATMEL_ID_UART0	27	/* UART 0 */
> +#define ATMEL_ID_UART1	28	/* UART 1 */
> +#define ATMEL_ID_USART2	29	/* USART 2 */
> +#define ATMEL_ID_USART3	30	/* USART 3 */
> +#define ATMEL_ID_USART4	31	/* USART 4 */
> +#define ATMEL_ID_TWI0	32	/* Two-Wire Interface 0 */
> +#define ATMEL_ID_TWI1	33	/* Two-Wire Interface 1 */
> +#define ATMEL_ID_TWI2	34	/* Two-Wire Interface 2 */
> +#define ATMEL_ID_MCI0	35	/* High Speed Multimedia Card Interface 0 */
> +#define ATMEL_ID_MCI1	36	/* High Speed Multimedia Card Interface 1 */
> +#define ATMEL_ID_SPI0	37	/* Serial Peripheral Interface 0 */
> +#define ATMEL_ID_SPI1	38	/* Serial Peripheral Interface 1 */
> +#define ATMEL_ID_SPI2	39	/* Serial Peripheral Interface 2 */
> +#define ATMEL_ID_TC0	40	/* Timer Counter 0 (ch. 0, 1, 2) */
> +#define ATMEL_ID_TC1	41	/* Timer Counter 1 (ch. 3, 4, 5) */
> +#define ATMEL_ID_TC2	42	/* Timer Counter 2 (ch. 6, 7, 8) */
> +#define ATMEL_ID_PWMC	43	/* Pulse Width Modulation Controller */
> +#define ATMEL_ID_ADC	44	/* Touch Screen ADC Controller */
> +#define ATMEL_ID_DBGU	45	/* Debug Unit Interrupt */
> +#define ATMEL_ID_UHPHS	46	/* USB Host High Speed */
> +#define ATMEL_ID_UDPHS	47	/* USB Device High Speed */
> +#define ATMEL_ID_SSC0	48	/* Synchronous Serial Controller 0 */
> +#define ATMEL_ID_SSC1	49	/* Synchronous Serial Controller 1 */
> +#define ATMEL_ID_XDMAC1	50	/* DMA Controller 1 */
> +#define ATMEL_ID_LCDC	51	/* LCD Controller */
> +#define ATMEL_ID_ISI	52	/* Image Sensor Interface */
> +#define ATMEL_ID_TRNG	53	/* True Random Number Generator */
> +#define ATMEL_ID_GMAC0	54	/* Ethernet MAC 0 */
> +#define ATMEL_ID_GMAC1	55	/* Ethernet MAC 1 */
> +#define ATMEL_ID_IRQ	56	/* IRQ Interrupt ID */
> +#define ATMEL_ID_SFC	57	/* Fuse Controller */
> +#define ATMEL_ID_SECURAM	59	/* Secured RAM */
> +#define ATMEL_ID_SMD	61	/* SMD Soft Modem */
> +#define ATMEL_ID_TWI3	62	/* Two-Wire Interface 3 */
> +#define ATMEL_ID_CATB	63	/* Capacitive Touch Controller */
> +#define ATMEL_ID_SFR	64	/* Special Funcion Register */
> +#define ATMEL_ID_AIC	65	/* Advanced Interrupt Controller */
> +#define ATMEL_ID_SAIC	66	/* Secured Advanced Interrupt Controller */
> +#define ATMEL_ID_L2CC	67	/* L2 Cache Controller */
> +
> +/*
> + * User Peripherals physical base addresses.
> + */
> +#define ATMEL_BASE_LCDC		0xf0000000
> +#define ATMEL_BASE_DMAC1	0xf0004000
> +#define ATMEL_BASE_ISI		0xf0008000
> +#define ATMEL_BASE_PKCC		0xf000C000
> +#define ATMEL_BASE_MPDDRC	0xf0010000
> +#define ATMEL_BASE_DMAC0	0xf0014000
> +#define ATMEL_BASE_PMC		0xf0018000
> +#define ATMEL_BASE_MATRIX0	0xf001c000
> +#define ATMEL_BASE_AESB		0xf0020000
> +/* Reserved: 0xf0024000 - 0xf8000000 */
> +#define ATMEL_BASE_MCI0		0xf8000000
> +#define ATMEL_BASE_UART0	0xf8004000
> +#define ATMEL_BASE_SSC0		0xf8008000
> +#define ATMEL_BASE_PWMC		0xf800c000
> +#define ATMEL_BASE_SPI0		0xf8010000
> +#define ATMEL_BASE_TWI0		0xf8014000
> +#define ATMEL_BASE_TWI1		0xf8018000
> +#define ATMEL_BASE_TC0		0xf801c000
> +#define ATMEL_BASE_GMAC0	0xf8020000
> +#define ATMEL_BASE_TWI2		0xf8024000
> +#define ATMEL_BASE_SFR		0xf8028000
> +#define ATMEL_BASE_USART0	0xf802c000
> +#define ATMEL_BASE_USART1	0xf8030000
> +/* Reserved:	0xf8034000 - 0xfc000000 */
> +#define ATMEL_BASE_MCI1		0xfc000000
> +#define ATMEL_BASE_UART1	0xfc004000
> +#define ATMEL_BASE_USART2	0xfc008000
> +#define ATMEL_BASE_USART3	0xfc00c000
> +#define ATMEL_BASE_USART4	0xfc010000
> +#define ATMEL_BASE_SSC1		0xfc014000
> +#define ATMEL_BASE_SPI1		0xfc018000
> +#define ATMEL_BASE_SPI2		0xfc01c000
> +#define ATMEL_BASE_TC1		0xfc020000
> +#define ATMEL_BASE_TC2		0xfc024000
> +#define ATMEL_BASE_GMAC1	0xfc028000
> +#define ATMEL_BASE_UDPHS	0xfc02c000
> +#define ATMEL_BASE_TRNG		0xfc030000
> +#define ATMEL_BASE_ADC		0xfc034000
> +#define ATMEL_BASE_TWI3		0xfc038000
> +
> +#define ATMEL_BASE_SMC		0xfc05c000
> +#define ATMEL_BASE_PMECC	(ATMEL_BASE_SMC + 0x070)
> +#define ATMEL_BASE_PMERRLOC	(ATMEL_BASE_SMC + 0x500)
> +
> +#define ATMEL_BASE_PIOD		0xfc068000
> +#define ATMEL_BASE_RSTC		0xfc068600
> +#define ATMEL_BASE_PIT		0xfc068630
> +#define ATMEL_BASE_WDT		0xfc068640
> +
> +#define ATMEL_BASE_DBGU		0xfc069000
> +#define ATMEL_BASE_PIOA		0xfc06a000
> +#define ATMEL_BASE_PIOB		0xfc06b000
> +#define ATMEL_BASE_PIOC		0xfc06c000
> +#define ATMEL_BASE_PIOE		0xfc06d000
> +#define ATMEL_BASE_AIC		0xfc06e000
> +
> +/*
> + * Internal Memory.
> + */
> +#define ATMEL_BASE_ROM		0x00000000	/* Internal ROM base address */
> +#define ATMEL_BASE_NFC		0x00100000	/* NFC SRAM */
> +#define ATMEL_BASE_SRAM		0x00200000	/* Internal ROM base address */
> +#define ATMEL_BASE_VDEC		0x00300000	/* Video Decoder Controller */
> +#define ATMEL_BASE_UDPHS_FIFO	0x00400000	/* USB Device HS controller */
> +#define ATMEL_BASE_OHCI		0x00500000	/* USB Host controller (OHCI) */
> +#define ATMEL_BASE_EHCI		0x00600000	/* USB Host controller (EHCI) */
> +#define ATMEL_BASE_AXI		0x00700000
> +#define ATMEL_BASE_DAP		0x00800000
> +#define ATMEL_BASE_SMD		0x00900000
> +
> +/*
> + * External memory
> + */
> +#define ATMEL_BASE_CS0		0x10000000
> +#define ATMEL_BASE_DDRCS	0x20000000
> +#define ATMEL_BASE_CS1		0x60000000
> +#define ATMEL_BASE_CS2		0x70000000
> +#define ATMEL_BASE_CS3		0x80000000
> +
> +/*
> + * Other misc defines
> + */
> +#define ATMEL_PIO_PORTS		5
> +#define CPU_HAS_PIO3
> +#define PIO_SCDR_DIV		0x3fff
> +#define CPU_HAS_PCR
> +#define CPU_HAS_H32MXDIV
> +
> +/*
> + * The clock of peripheral connect to H32MX is decided by H32MXDIV
> + * bit in MCKR, if this bit is set, the peripheral only work at half
> + * of MCK, the MCKR address is 0xf0018030, and H32MXDIV is bit 24.
> + */
> +#define H32MXDIV	(readl(0xF0018030) & (1 << 24) ? 2 : 1)

Could we use ATMEL_BASE_PMC + <some new define> here?

> +
> +/*
> + * No PMECC Galois table in ROM
> + */
> +#define NO_GALOIS_TABLE_IN_ROM
> +
> +#ifndef __ASSEMBLY__
> +unsigned int get_chip_id(void);
> +unsigned int get_extension_chip_id(void);
> +unsigned int has_emac(void);
> +unsigned int has_gmac(void);
> +unsigned int has_lcdc(void);
> +char *get_cpu_name(void);
> +#endif
> +
> +#endif
> diff --git a/board/atmel/sama5d4ek/Kconfig b/board/atmel/sama5d4ek/Kconfig
> new file mode 100644
> index 0000000..a889895
> --- /dev/null
> +++ b/board/atmel/sama5d4ek/Kconfig
> @@ -0,0 +1,18 @@
> +if TARGET_SAMA5D4EK
> +
> +config SYS_CPU
> +	default "armv7"
> +
> +config SYS_BOARD
> +	default "sama5d4ek"
> +
> +config SYS_VENDOR
> +	default "atmel"
> +
> +config SYS_SOC
> +	default "at91"
> +
> +config SYS_CONFIG_NAME
> +	default "sama5d4ek"
> +
> +endif
> diff --git a/board/atmel/sama5d4ek/MAINTAINERS b/board/atmel/sama5d4ek/MAINTAINERS
> new file mode 100644
> index 0000000..afe88dd
> --- /dev/null
> +++ b/board/atmel/sama5d4ek/MAINTAINERS
> @@ -0,0 +1,8 @@
> +SAMA5D4EK BOARD
> +M:	Bo Shen <voice.shen@atmel.com>
> +S:	Maintained
> +F:	board/atmel/sama5d4ek/
> +F:	include/configs/sama5d4ek.h
> +F:	configs/sama5d4ek_mmc_defconfig
> +F:	configs/sama5d4ek_nandflash_defconfig
> +F:	configs/sama5d4ek_spiflash_defconfig
> diff --git a/board/atmel/sama5d4ek/Makefile b/board/atmel/sama5d4ek/Makefile
> new file mode 100644
> index 0000000..d91525c
> --- /dev/null
> +++ b/board/atmel/sama5d4ek/Makefile
> @@ -0,0 +1,15 @@
> +#
> +# (C) Copyright 2003-2008
> +# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
> +#
> +# (C) Copyright 2008
> +# Stelian Pop <stelian@popies.net>
> +# Lead Tech Design <www.leadtechdesign.com>
> +#
> +# (C) Copyright 2014
> +# Bo Shen <voice.shen@atmel.com>
> +#
> +# SPDX-License-Identifier:	GPL-2.0+
> +#
> +
> +obj-y += sama5d4ek.o
> diff --git a/board/atmel/sama5d4ek/sama5d4ek.c b/board/atmel/sama5d4ek/sama5d4ek.c
> new file mode 100644
> index 0000000..099b924
> --- /dev/null
> +++ b/board/atmel/sama5d4ek/sama5d4ek.c
> @@ -0,0 +1,322 @@
> +/*
> + * Copyright (C) 2014 Atmel
> + *		      Bo Shen <voice.shen@atmel.com>
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include <asm/arch/at91_common.h>
> +#include <asm/arch/at91_pmc.h>
> +#include <asm/arch/at91_rstc.h>
> +#include <asm/arch/gpio.h>
> +#include <asm/arch/clk.h>
> +#include <asm/arch/sama5d3_smc.h>
> +#include <asm/arch/sama5d4.h>
> +#include <atmel_lcdc.h>
> +#include <atmel_mci.h>
> +#include <lcd.h>
> +#include <mmc.h>
> +#include <net.h>
> +#include <netdev.h>
> +#include <nand.h>
> +#include <spi.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +#ifdef CONFIG_ATMEL_SPI
> +int spi_cs_is_valid(unsigned int bus, unsigned int cs)
> +{
> +	return bus == 0 && cs == 0;
> +}
> +
> +void spi_cs_activate(struct spi_slave *slave)
> +{
> +	at91_set_pio_output(AT91_PIO_PORTC, 3, 0);
> +}
> +
> +void spi_cs_deactivate(struct spi_slave *slave)
> +{
> +	at91_set_pio_output(AT91_PIO_PORTC, 3, 1);
> +}
> +
> +static void sama5d4ek_spi0_hw_init(void)
> +{
> +	at91_set_a_periph(AT91_PIO_PORTC, 0, 0);	/* SPI0_MISO */
> +	at91_set_a_periph(AT91_PIO_PORTC, 1, 0);	/* SPI0_MOSI */
> +	at91_set_a_periph(AT91_PIO_PORTC, 2, 0);	/* SPI0_SPCK */
> +
> +	at91_set_pio_output(AT91_PIO_PORTC, 3, 1);	/* SPI0_CS0 */
> +
> +	/* Enable clock */
> +	at91_periph_clk_enable(ATMEL_ID_SPI0);
> +}
> +#endif /* CONFIG_ATMEL_SPI */
> +
> +#ifdef CONFIG_NAND_ATMEL
> +static void sama5d4ek_nand_hw_init(void)
> +{
> +	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
> +
> +	at91_periph_clk_enable(ATMEL_ID_SMC);
> +
> +	/* Configure SMC CS3 for NAND */
> +	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) |
> +	       AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(1),
> +	       &smc->cs[3].setup);
> +	writel(AT91_SMC_PULSE_NWE(2) | AT91_SMC_PULSE_NCS_WR(3) |
> +	       AT91_SMC_PULSE_NRD(2) | AT91_SMC_PULSE_NCS_RD(3),
> +	       &smc->cs[3].pulse);
> +	writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
> +	       &smc->cs[3].cycle);
> +	writel(AT91_SMC_TIMINGS_TCLR(2) | AT91_SMC_TIMINGS_TADL(7) |
> +	       AT91_SMC_TIMINGS_TAR(2)  | AT91_SMC_TIMINGS_TRR(3)   |
> +	       AT91_SMC_TIMINGS_TWB(7)  | AT91_SMC_TIMINGS_RBNSEL(3)|
> +	       AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings);
> +	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
> +	       AT91_SMC_MODE_EXNW_DISABLE |
> +	       AT91_SMC_MODE_DBW_8 |
> +	       AT91_SMC_MODE_TDF_CYCLE(3),
> +	       &smc->cs[3].mode);
> +
> +	at91_set_a_periph(AT91_PIO_PORTC, 5, 0);	/* D0 */
> +	at91_set_a_periph(AT91_PIO_PORTC, 6, 0);	/* D1 */
> +	at91_set_a_periph(AT91_PIO_PORTC, 7, 0);	/* D2 */
> +	at91_set_a_periph(AT91_PIO_PORTC, 8, 0);	/* D3 */
> +	at91_set_a_periph(AT91_PIO_PORTC, 9, 0);	/* D4 */
> +	at91_set_a_periph(AT91_PIO_PORTC, 10, 0);	/* D5 */
> +	at91_set_a_periph(AT91_PIO_PORTC, 11, 0);	/* D6 */
> +	at91_set_a_periph(AT91_PIO_PORTC, 12, 0);	/* D7 */
> +	at91_set_a_periph(AT91_PIO_PORTC, 13, 0);	/* RE */
> +	at91_set_a_periph(AT91_PIO_PORTC, 14, 0);	/* WE */
> +	at91_set_a_periph(AT91_PIO_PORTC, 15, 1);	/* NCS */
> +	at91_set_a_periph(AT91_PIO_PORTC, 16, 1);	/* RDY */
> +	at91_set_a_periph(AT91_PIO_PORTC, 17, 1);	/* ALE */
> +	at91_set_a_periph(AT91_PIO_PORTC, 18, 1);	/* CLE */
> +}
> +#endif
> +
> +#ifdef CONFIG_CMD_USB
> +static void sama5d4ek_usb_hw_init(void)
> +{
> +	at91_set_pio_output(AT91_PIO_PORTE, 11, 0);
> +	at91_set_pio_output(AT91_PIO_PORTE, 12, 0);
> +	at91_set_pio_output(AT91_PIO_PORTE, 10, 0);
> +}
> +#endif
> +
> +#ifdef CONFIG_LCD
> +vidinfo_t panel_info = {
> +	.vl_col = 800,
> +	.vl_row = 480,
> +	.vl_clk = 33260000,
> +	.vl_sync = ATMEL_LCDC_INVLINE_NORMAL | ATMEL_LCDC_INVFRAME_NORMAL,
> +	.vl_bpix = LCD_BPP,
> +	.vl_tft = 1,
> +	.vl_hsync_len = 5,
> +	.vl_left_margin = 128,
> +	.vl_right_margin = 0,
> +	.vl_vsync_len = 5,
> +	.vl_upper_margin = 23,
> +	.vl_lower_margin = 22,
> +	.mmio = ATMEL_BASE_LCDC,
> +};
> +
> +/* No power up/down pin for the LCD pannel */
> +void lcd_enable(void)	{ /* Empty! */ }
> +void lcd_disable(void)	{ /* Empty! */ }
> +
> +unsigned int has_lcdc(void)
> +{
> +	return 1;
> +}
> +
> +static void sama5d4ek_lcd_hw_init(void)
> +{
> +	at91_set_a_periph(AT91_PIO_PORTA, 24, 0);	/* LCDPWM */
> +	at91_set_a_periph(AT91_PIO_PORTA, 25, 0);	/* LCDDISP */
> +	at91_set_a_periph(AT91_PIO_PORTA, 26, 0);	/* LCDVSYNC */
> +	at91_set_a_periph(AT91_PIO_PORTA, 27, 0);	/* LCDHSYNC */
> +	at91_set_a_periph(AT91_PIO_PORTA, 28, 0);	/* LCDDOTCK */
> +	at91_set_a_periph(AT91_PIO_PORTA, 29, 0);	/* LCDDEN */
> +
> +	at91_set_a_periph(AT91_PIO_PORTA,  2, 0);	/* LCDD2 */
> +	at91_set_a_periph(AT91_PIO_PORTA,  3, 0);	/* LCDD3 */
> +	at91_set_a_periph(AT91_PIO_PORTA,  4, 0);	/* LCDD4 */
> +	at91_set_a_periph(AT91_PIO_PORTA,  5, 0);	/* LCDD5 */
> +	at91_set_a_periph(AT91_PIO_PORTA,  6, 0);	/* LCDD6 */
> +	at91_set_a_periph(AT91_PIO_PORTA,  7, 0);	/* LCDD7 */
> +
> +	at91_set_a_periph(AT91_PIO_PORTA, 10, 0);	/* LCDD10 */
> +	at91_set_a_periph(AT91_PIO_PORTA, 11, 0);	/* LCDD11 */
> +	at91_set_a_periph(AT91_PIO_PORTA, 12, 0);	/* LCDD12 */
> +	at91_set_a_periph(AT91_PIO_PORTA, 13, 0);	/* LCDD13 */
> +	at91_set_a_periph(AT91_PIO_PORTA, 14, 0);	/* LCDD14 */
> +	at91_set_a_periph(AT91_PIO_PORTA, 15, 0);	/* LCDD15 */
> +
> +	at91_set_a_periph(AT91_PIO_PORTA, 18, 0);	/* LCDD18 */
> +	at91_set_a_periph(AT91_PIO_PORTA, 19, 0);	/* LCDD19 */
> +	at91_set_a_periph(AT91_PIO_PORTA, 20, 0);	/* LCDD20 */
> +	at91_set_a_periph(AT91_PIO_PORTA, 21, 0);	/* LCDD21 */
> +	at91_set_a_periph(AT91_PIO_PORTA, 22, 0);	/* LCDD22 */
> +	at91_set_a_periph(AT91_PIO_PORTA, 23, 0);	/* LCDD23 */
> +
> +	/* Enable clock */
> +	at91_periph_clk_enable(ATMEL_ID_LCDC);
> +}
> +
> +#ifdef CONFIG_LCD_INFO
> +void lcd_show_board_info(void)
> +{
> +	ulong dram_size, nand_size;
> +	int i;
> +	char temp[32];
> +
> +	lcd_printf("2014 ATMEL Corp\n");
> +	lcd_printf("at91@atmel.com\n");
> +	lcd_printf("%s CPU at %s MHz\n", get_cpu_name(),
> +		   strmhz(temp, get_cpu_clk_rate()));
> +
> +	dram_size = 0;
> +	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
> +		dram_size += gd->bd->bi_dram[i].size;
> +
> +	nand_size = 0;
> +#ifdef CONFIG_NAND_ATMEL
> +	for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
> +		nand_size += nand_info[i].size;
> +#endif
> +	lcd_printf("%ld MB SDRAM, %ld MB NAND\n",
> +		   dram_size >> 20, nand_size >> 20);
> +}
> +#endif /* CONFIG_LCD_INFO */
> +
> +#endif /* CONFIG_LCD */
> +
> +#ifdef CONFIG_GENERIC_ATMEL_MCI
> +void sama5d4ek_mci1_hw_init(void)
> +{
> +	at91_set_c_periph(AT91_PIO_PORTE, 19, 1);	/* MCI1 CDA */
> +	at91_set_c_periph(AT91_PIO_PORTE, 20, 1);	/* MCI1 DA0 */
> +	at91_set_c_periph(AT91_PIO_PORTE, 21, 1);	/* MCI1 DA1 */
> +	at91_set_c_periph(AT91_PIO_PORTE, 22, 1);	/* MCI1 DA2 */
> +	at91_set_c_periph(AT91_PIO_PORTE, 23, 1);	/* MCI1 DA3 */
> +	at91_set_c_periph(AT91_PIO_PORTE, 18, 0);	/* MCI1 CLK */
> +
> +	/*
> +	 * As the mci io internal pull down is too strong, so if the io needs
> +	 * external pull up, the pull up resistor will be very small, if so
> +	 * the power consumption will increase, so disable the interanl pull
> +	 * down to save the power.
> +	 */
> +	at91_set_pio_pulldown(AT91_PIO_PORTE, 18, 0);
> +	at91_set_pio_pulldown(AT91_PIO_PORTE, 19, 0);
> +	at91_set_pio_pulldown(AT91_PIO_PORTE, 20, 0);
> +	at91_set_pio_pulldown(AT91_PIO_PORTE, 21, 0);
> +	at91_set_pio_pulldown(AT91_PIO_PORTE, 22, 0);
> +	at91_set_pio_pulldown(AT91_PIO_PORTE, 23, 0);
> +
> +	/* Enable clock */
> +	at91_periph_clk_enable(ATMEL_ID_MCI1);
> +}
> +
> +int board_mmc_init(bd_t *bis)
> +{
> +	/* Enable power for MCI1 interface */
> +	at91_set_pio_output(AT91_PIO_PORTE, 15, 0);
> +
> +	return atmel_mci_init((void *)ATMEL_BASE_MCI1);
> +}
> +#endif /* CONFIG_GENERIC_ATMEL_MCI */
> +
> +#ifdef CONFIG_MACB
> +void sama5d4ek_macb0_hw_init(void)
> +{
> +	at91_set_a_periph(AT91_PIO_PORTB, 0, 0);	/* ETXCK_EREFCK */
> +	at91_set_a_periph(AT91_PIO_PORTB, 6, 0);	/* ERXDV */
> +	at91_set_a_periph(AT91_PIO_PORTB, 8, 0);	/* ERX0 */
> +	at91_set_a_periph(AT91_PIO_PORTB, 9, 0);	/* ERX1 */
> +	at91_set_a_periph(AT91_PIO_PORTB, 7, 0);	/* ERXER */
> +	at91_set_a_periph(AT91_PIO_PORTB, 2, 0);	/* ETXEN */
> +	at91_set_a_periph(AT91_PIO_PORTB, 12, 0);	/* ETX0 */
> +	at91_set_a_periph(AT91_PIO_PORTB, 13, 0);	/* ETX1 */
> +	at91_set_a_periph(AT91_PIO_PORTB, 17, 0);	/* EMDIO */
> +	at91_set_a_periph(AT91_PIO_PORTB, 16, 0);	/* EMDC */
> +
> +	/* Enable clock */
> +	at91_periph_clk_enable(ATMEL_ID_GMAC0);
> +}
> +#endif
> +
> +char *get_cpu_name()
> +{
> +	return "SAMA5D4";
> +}

Since when is the get_cpu_name() a board function? This should be placed
in some SoC file. Generally I'm missing a sama5d4_devices.c There should
be placed some of the functions here in the board code.

> +
> +static void sama5d4ek_serial3_hw_init(void)
> +{
> +	at91_set_b_periph(AT91_PIO_PORTE, 17, 1);	/* TXD3 */
> +	at91_set_b_periph(AT91_PIO_PORTE, 16, 0);	/* RXD3 */
> +
> +	/* Enable clock */
> +	at91_periph_clk_enable(ATMEL_ID_USART3);
> +}
> +
> +int board_early_init_f(void)
> +{
> +	at91_periph_clk_enable(ATMEL_ID_PIOA);
> +	at91_periph_clk_enable(ATMEL_ID_PIOB);
> +	at91_periph_clk_enable(ATMEL_ID_PIOC);
> +	at91_periph_clk_enable(ATMEL_ID_PIOD);
> +	at91_periph_clk_enable(ATMEL_ID_PIOE);
> +
> +	sama5d4ek_serial3_hw_init();
> +
> +	return 0;
> +}
> +
> +int board_init(void)
> +{
> +	/* adress of boot parameters */
> +	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
> +
> +#ifdef CONFIG_ATMEL_SPI
> +	sama5d4ek_spi0_hw_init();
> +#endif
> +#ifdef CONFIG_NAND_ATMEL
> +	sama5d4ek_nand_hw_init();
> +#endif
> +#ifdef CONFIG_GENERIC_ATMEL_MCI
> +	sama5d4ek_mci1_hw_init();
> +#endif
> +#ifdef CONFIG_MACB
> +	sama5d4ek_macb0_hw_init();
> +#endif
> +#ifdef CONFIG_LCD
> +	sama5d4ek_lcd_hw_init();
> +#endif
> +#ifdef CONFIG_CMD_USB
> +	sama5d4ek_usb_hw_init();
> +#endif
> +
> +	return 0;
> +}
> +
> +int dram_init(void)
> +{
> +	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
> +				    CONFIG_SYS_SDRAM_SIZE);
> +	return 0;
> +}
> +
> +int board_eth_init(bd_t *bis)
> +{
> +	int rc = 0;
> +
> +#ifdef CONFIG_MACB
> +	rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00);
> +#endif
> +
> +	return rc;
> +}
> diff --git a/configs/sama5d4ek_mmc_defconfig b/configs/sama5d4ek_mmc_defconfig
> new file mode 100644
> index 0000000..16a5ed7
> --- /dev/null
> +++ b/configs/sama5d4ek_mmc_defconfig
> @@ -0,0 +1,3 @@
> +CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_MMC"
> ++S:CONFIG_ARM=y
> ++S:CONFIG_TARGET_SAMA5D4EK=y
> diff --git a/configs/sama5d4ek_nandflash_defconfig b/configs/sama5d4ek_nandflash_defconfig
> new file mode 100644
> index 0000000..8b7fbc3
> --- /dev/null
> +++ b/configs/sama5d4ek_nandflash_defconfig
> @@ -0,0 +1,3 @@
> +CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_NANDFLASH"
> ++S:CONFIG_ARM=y
> ++S:CONFIG_TARGET_SAMA5D4EK=y
> diff --git a/configs/sama5d4ek_spiflash_defconfig b/configs/sama5d4ek_spiflash_defconfig
> new file mode 100644
> index 0000000..63e9b6c
> --- /dev/null
> +++ b/configs/sama5d4ek_spiflash_defconfig
> @@ -0,0 +1,3 @@
> +CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_SERIALFLASH"
> ++S:CONFIG_ARM=y
> ++S:CONFIG_TARGET_SAMA5D4EK=y
> diff --git a/include/configs/sama5d4ek.h b/include/configs/sama5d4ek.h
> new file mode 100644
> index 0000000..d50897e
> --- /dev/null
> +++ b/include/configs/sama5d4ek.h
> @@ -0,0 +1,215 @@
> +/*
> + * Configuration settings for the SAMA5D4EK board.
> + *
> + * Copyright (C) 2014 Atmel
> + *		      Bo Shen <voice.shen@atmel.com>
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#include <asm/hardware.h>
> +
> +#define CONFIG_SYS_TEXT_BASE		0x26f00000
> +
> +/* ARM asynchronous clock */
> +#define CONFIG_SYS_AT91_SLOW_CLOCK      32768
> +#define CONFIG_SYS_AT91_MAIN_CLOCK      12000000 /* from 12 MHz crystal */
> +#define CONFIG_SYS_HZ		        1000
> +
> +#define CONFIG_ARCH_CPU_INIT
> +
> +#define CONFIG_SKIP_LOWLEVEL_INIT
> +#define CONFIG_BOARD_EARLY_INIT_F
> +#define CONFIG_DISPLAY_CPUINFO
> +
> +#define CONFIG_CMD_BOOTZ
> +#define CONFIG_OF_LIBFDT		/* Device Tree support */
> +
> +#define CONFIG_SYS_GENERIC_BOARD
> +
> +/* general purpose I/O */
> +#define CONFIG_AT91_GPIO
> +
> +/* serial console */
> +#define CONFIG_ATMEL_USART
> +#define CONFIG_USART_BASE		ATMEL_BASE_USART3
> +#define	CONFIG_USART_ID			ATMEL_ID_USART3
> +
> +#define CONFIG_BOOTDELAY		3
> +
> +/*
> + * BOOTP options
> + */
> +#define CONFIG_BOOTP_BOOTFILESIZE
> +#define CONFIG_BOOTP_BOOTPATH
> +#define CONFIG_BOOTP_GATEWAY
> +#define CONFIG_BOOTP_HOSTNAME
> +
> +/* No NOR flash */
> +#define CONFIG_SYS_NO_FLASH
> +
> +/*
> + * Command line configuration.
> + */
> +#include <config_cmd_default.h>
> +#undef CONFIG_CMD_FPGA
> +#undef CONFIG_CMD_IMI
> +#undef CONFIG_CMD_LOADS
> +#define CONFIG_CMD_PING
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_CMD_SETEXPR
> +
> +/* SDRAM */
> +#define CONFIG_NR_DRAM_BANKS		1
> +#define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
> +#define CONFIG_SYS_SDRAM_SIZE		0x20000000
> +
> +#define CONFIG_SYS_INIT_SP_ADDR \
> +	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
> +
> +#define CONFIG_SYS_LOAD_ADDR		0x22000000 /* load address */
> +
> +/* SerialFlash */
> +#define CONFIG_CMD_SF
> +
> +#ifdef CONFIG_CMD_SF
> +#define CONFIG_ATMEL_SPI
> +#define CONFIG_ATMEL_SPI0
> +#define CONFIG_SPI_FLASH
> +#define CONFIG_SPI_FLASH_ATMEL
> +#define CONFIG_SF_DEFAULT_BUS		0
> +#define CONFIG_SF_DEFAULT_CS		0
> +#define CONFIG_SF_DEFAULT_SPEED		30000000
> +#endif
> +
> +/* NAND flash */
> +#define CONFIG_CMD_NAND
> +
> +#ifdef CONFIG_CMD_NAND
> +#define CONFIG_NAND_ATMEL
> +#define CONFIG_SYS_MAX_NAND_DEVICE	1
> +#define CONFIG_SYS_NAND_BASE		ATMEL_BASE_CS3
> +/* our ALE is AD21 */
> +#define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
> +/* our CLE is AD22 */
> +#define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
> +#define CONFIG_SYS_NAND_ONFI_DETECTION
> +/* PMECC & PMERRLOC */
> +#define CONFIG_ATMEL_NAND_HWECC
> +#define CONFIG_ATMEL_NAND_HW_PMECC
> +#endif
> +
> +/* MMC */
> +#define CONFIG_CMD_MMC
> +
> +#ifdef CONFIG_CMD_MMC
> +#define CONFIG_MMC
> +#define CONFIG_GENERIC_MMC
> +#define CONFIG_GENERIC_ATMEL_MCI
> +#define ATMEL_BASE_MMCI			ATMEL_BASE_MCI1
> +#endif
> +
> +/* USB */
> +#define CONFIG_CMD_USB
> +
> +#ifdef CONFIG_CMD_USB
> +#define CONFIG_USB_EHCI
> +#define CONFIG_USB_EHCI_ATMEL
> +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	3
> +#define CONFIG_USB_STORAGE
> +#endif
> +
> +#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
> +#define CONFIG_CMD_FAT
> +#define CONFIG_DOS_PARTITION
> +#endif
> +
> +/* Ethernet Hardware */
> +#define CONFIG_MACB
> +#define CONFIG_RMII
> +#define CONFIG_NET_RETRY_COUNT		20
> +#define CONFIG_MACB_SEARCH_PHY
> +
> +/* LCD */
> +#define CONFIG_LCD
> +#define LCD_BPP				LCD_COLOR16
> +#define LCD_OUTPUT_BPP                  18
> +#define CONFIG_LCD_LOGO
> +#define CONFIG_LCD_INFO
> +#define CONFIG_LCD_INFO_BELOW_LOGO
> +#define CONFIG_SYS_WHITE_ON_BLACK
> +#define CONFIG_ATMEL_HLCD
> +#define CONFIG_ATMEL_LCD_RGB565
> +#define CONFIG_SYS_CONSOLE_IS_IN_ENV
> +
> +#ifdef CONFIG_SYS_USE_SERIALFLASH
> +/* bootstrap + u-boot + env + linux in serial flash */
> +#define CONFIG_ENV_IS_IN_SPI_FLASH
> +#define CONFIG_ENV_SPI_BUS	CONFIG_SF_DEFAULT_BUS
> +#define CONFIG_ENV_SPI_CS	CONFIG_SF_DEFAULT_CS
> +#define CONFIG_ENV_OFFSET       0x10000
> +#define CONFIG_ENV_SIZE         0x10000
> +#define CONFIG_ENV_SECT_SIZE    0x1000
> +#define CONFIG_BOOTCOMMAND      "sf probe 0; " \
> +				"sf read 0x21000000 0xa0000 0x60000; " \
> +				"sf read 0x22000000 0x100000 0x300000; " \
> +				"bootz 0x22000000 - 0x21000000"
> +#elif CONFIG_SYS_USE_NANDFLASH
> +/* bootstrap + u-boot + env in nandflash */
> +#define CONFIG_ENV_IS_IN_NAND
> +#define CONFIG_ENV_OFFSET		0xc0000
> +#define CONFIG_ENV_OFFSET_REDUND	0x100000
> +#define CONFIG_ENV_SIZE			0x20000
> +#define CONFIG_BOOTCOMMAND	"nand read 0x21000000 0x180000 0x80000;" \
> +				"nand read 0x22000000 0x200000 0x600000;" \
> +				"bootz 0x22000000 - 0x21000000"
> +#elif CONFIG_SYS_USE_MMC
> +/* bootstrap + u-boot + env in sd card */
> +#define CONFIG_ENV_IS_IN_FAT
> +#define CONFIG_FAT_WRITE
> +#define FAT_ENV_INTERFACE	"mmc"
> +/*
> + * We don't specify the part number, if device 0 has partition table, it means
> + * the first partition; it no partition table, then take whole device as a
> + * FAT file system.
> + */
> +#define FAT_ENV_DEVICE_AND_PART	"0"
> +#define FAT_ENV_FILE		"uboot.env"
> +#define CONFIG_ENV_SIZE		0x4000
> +#define CONFIG_BOOTCOMMAND	"fatload mmc 0:1 0x21000000 sama5d4ek.dtb; " \
> +				"fatload mmc 0:1 0x22000000 zImage; " \
> +				"bootz 0x22000000 - 0x21000000"
> +#endif
> +
> +#ifdef CONFIG_SYS_USE_MMC
> +#define CONFIG_BOOTARGS							\
> +	"console=ttyS0,115200 earlyprintk "				\
> +	"root=/dev/mmcblk0p2 rw rootwait"
> +#else
> +#define CONFIG_BOOTARGS							\
> +	"console=ttyS0,115200 earlyprintk "				\
> +	"mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,"		\
> +	"256K(env),256k(evn_redundent),256k(spare),"			\
> +	"512k(dtb),6M(kernel)ro,-(rootfs) "				\
> +	"rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs"
> +#endif
> +
> +#define CONFIG_BAUDRATE			115200
> +
> +#define CONFIG_SYS_PROMPT		"U-Boot> "
> +#define CONFIG_SYS_CBSIZE		256
> +#define CONFIG_SYS_MAXARGS		16
> +#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
> +					sizeof(CONFIG_SYS_PROMPT) + 16)
> +#define CONFIG_SYS_LONGHELP
> +#define CONFIG_CMDLINE_EDITING
> +#define CONFIG_AUTO_COMPLETE
> +#define CONFIG_SYS_HUSH_PARSER
> +
> +/* Size of malloc() pool */
> +#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
> +
> +#endif
> 

Best Regards

Andreas Bießmann
Bo Shen Oct. 27, 2014, 3:25 a.m. UTC | #2 
Hi Andreas,

On 10/25/2014 08:26 AM, Andreas Bießmann wrote:
> Hi Bo,
>
> On 16.09.14 09:57, Bo Shen wrote:
>> The code for this board supports following features:
>>    - Boot media support: NAND flash/SD card/SPI flash
>>    - Support LCD display
>>    - Support ethernet
>>    - Support USB mass storage
>>
>> Signed-off-by: Bo Shen <voice.shen@atmel.com>
>> ---
>>
>>   arch/arm/Kconfig                          |   4 +
>>   arch/arm/cpu/armv7/at91/timer.c           |   3 +-
>>   arch/arm/include/asm/arch-at91/at91_pmc.h |   6 +-
>>   arch/arm/include/asm/arch-at91/clk.h      |  29 +++
>>   arch/arm/include/asm/arch-at91/hardware.h |   2 +
>>   arch/arm/include/asm/arch-at91/sama5d4.h  | 199 ++++++++++++++++++
>>   board/atmel/sama5d4ek/Kconfig             |  18 ++
>>   board/atmel/sama5d4ek/MAINTAINERS         |   8 +
>>   board/atmel/sama5d4ek/Makefile            |  15 ++
>>   board/atmel/sama5d4ek/sama5d4ek.c         | 322 ++++++++++++++++++++++++++++++
>>   configs/sama5d4ek_mmc_defconfig           |   3 +
>>   configs/sama5d4ek_nandflash_defconfig     |   3 +
>>   configs/sama5d4ek_spiflash_defconfig      |   3 +
>>   include/configs/sama5d4ek.h               | 215 ++++++++++++++++++++
>>   14 files changed, 826 insertions(+), 4 deletions(-)
>>   create mode 100644 arch/arm/include/asm/arch-at91/sama5d4.h
>>   create mode 100644 board/atmel/sama5d4ek/Kconfig
>>   create mode 100644 board/atmel/sama5d4ek/MAINTAINERS
>>   create mode 100644 board/atmel/sama5d4ek/Makefile
>>   create mode 100644 board/atmel/sama5d4ek/sama5d4ek.c
>>   create mode 100644 configs/sama5d4ek_mmc_defconfig
>>   create mode 100644 configs/sama5d4ek_nandflash_defconfig
>>   create mode 100644 configs/sama5d4ek_spiflash_defconfig
>>   create mode 100644 include/configs/sama5d4ek.h
>>
>> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
>> index c8537bb..bbccd46 100644
>> --- a/arch/arm/Kconfig
>> +++ b/arch/arm/Kconfig
>> @@ -321,6 +321,9 @@ config TARGET_SAMA5D3_XPLAINED
>>   config TARGET_SAMA5D3XEK
>>   	bool "Support sama5d3xek"
>>
>> +config TARGET_SAMA5D4EK
>> +	bool "Support sama5d4ek"
>> +
>>   config TARGET_BCM28155_AP
>>   	bool "Support bcm28155_ap"
>>
>> @@ -569,6 +572,7 @@ source "board/atmel/at91sam9rlek/Kconfig"
>>   source "board/atmel/at91sam9x5ek/Kconfig"
>>   source "board/atmel/sama5d3_xplained/Kconfig"
>>   source "board/atmel/sama5d3xek/Kconfig"
>> +source "board/atmel/sama5d4ek/Kconfig"
>>   source "board/balloon3/Kconfig"
>>   source "board/barco/titanium/Kconfig"
>>   source "board/bluegiga/apx4devkit/Kconfig"
>> diff --git a/arch/arm/cpu/armv7/at91/timer.c b/arch/arm/cpu/armv7/at91/timer.c
>> index e3ebfe0..19bf80b 100644
>> --- a/arch/arm/cpu/armv7/at91/timer.c
>> +++ b/arch/arm/cpu/armv7/at91/timer.c
>> @@ -65,7 +65,8 @@ int timer_init(void)
>>   	/* Enable PITC */
>>   	writel(TIMER_LOAD_VAL | AT91_PIT_MR_EN , &pit->mr);
>>
>> -	gd->arch.timer_rate_hz = gd->arch.mck_rate_hz / 16;
>> +	gd->arch.timer_rate_hz = get_pit_clk_rate() / 16;
>> +
>
> is this part related to sama5d4ek or is it a generic fix? Could yopu
> please send as an extra patch if it's the latter?

This is part related to sama5d4ek, as we introduce the H32MXDIV.

>
>>   	gd->arch.tbu = 0;
>>   	gd->arch.tbl = 0;
>>
>> diff --git a/arch/arm/include/asm/arch-at91/at91_pmc.h b/arch/arm/include/asm/arch-at91/at91_pmc.h
>> index 27331ff..e81ece9 100644
>> --- a/arch/arm/include/asm/arch-at91/at91_pmc.h
>> +++ b/arch/arm/include/asm/arch-at91/at91_pmc.h
>> @@ -78,7 +78,7 @@ typedef struct at91_pmc {
>>   #define AT91_PMC_PLLXR_DIV(x)		(x & 0xFF)
>>   #define AT91_PMC_PLLXR_PLLCOUNT(x)	((x & 0x3F) << 8)
>>   #define AT91_PMC_PLLXR_OUT(x)		((x & 0x03) << 14)
>> -#ifdef CONFIG_SAMA5D3
>> +#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
>>   #define AT91_PMC_PLLXR_MUL(x)		((x & 0x7F) << 18)
>>   #else
>>   #define AT91_PMC_PLLXR_MUL(x)		((x & 0x7FF) << 16)
>> @@ -97,7 +97,7 @@ typedef struct at91_pmc {
>>   #define AT91_PMC_MCKR_CSS_PLLB		0x00000003
>>   #define AT91_PMC_MCKR_CSS_MASK		0x00000003
>>
>> -#ifdef CONFIG_SAMA5D3
>> +#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
>>   #define AT91_PMC_MCKR_PRES_1		0x00000000
>>   #define AT91_PMC_MCKR_PRES_2		0x00000010
>>   #define AT91_PMC_MCKR_PRES_4		0x00000020
>> @@ -126,7 +126,7 @@ typedef struct at91_pmc {
>>   #else
>>   #define AT91_PMC_MCKR_MDIV_1		0x00000000
>>   #define AT91_PMC_MCKR_MDIV_2		0x00000100
>> -#ifdef CONFIG_SAMA5D3
>> +#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
>>   #define AT91_PMC_MCKR_MDIV_3		0x00000300
>>   #endif
>>   #define AT91_PMC_MCKR_MDIV_4		0x00000200
>> diff --git a/arch/arm/include/asm/arch-at91/clk.h b/arch/arm/include/asm/arch-at91/clk.h
>> index 4076a78..7615018 100644
>> --- a/arch/arm/include/asm/arch-at91/clk.h
>> +++ b/arch/arm/include/asm/arch-at91/clk.h
>> @@ -50,12 +50,20 @@ static inline u32 get_pllb_init(void)
>>
>>   static inline unsigned long get_macb_pclk_rate(unsigned int dev_id)
>>   {
>> +#ifdef CPU_HAS_H32MXDIV
>> +	return get_mck_clk_rate() / H32MXDIV;
>> +#else
>
> I wonder if we should introduce H32MXDIV for all atmel SoC and remove
> the CPU_HAS_H32MXDIV here. A division by 1 should be optimized away if
> it is a constant. After all this piece of code would be more readable.

I don't think that a good idea, as the H32MXDIV is only appear in 
SAMA5D4 SoC, it is a bit in Master Clock Register (MCKR) and whether the 
H32MXDIV is set according to the master clock frequency. If H32MXDIV is 
set, then div2, or else div 1. Maybe a better way is:
--->8---
#ifdef CPU_HAS_H32MXDIV
	if (H32MXDIV)
		return get_mck_clk_rate() / 2;
	else
		return get_mck_clk_rate();
#else
	...
---8<---

>>   	return get_mck_clk_rate();
>> +#endif
>>   }
>>
>>   static inline unsigned long get_usart_clk_rate(unsigned int dev_id)
>>   {
>> +#ifdef CPU_HAS_H32MXDIV
>> +	return get_mck_clk_rate() / H32MXDIV;
>> +#else
>>   	return get_mck_clk_rate();
>> +#endif
>>   }
>>
>>   static inline unsigned long get_lcdc_clk_rate(unsigned int dev_id)
>> @@ -65,17 +73,38 @@ static inline unsigned long get_lcdc_clk_rate(unsigned int dev_id)
>>
>>   static inline unsigned long get_spi_clk_rate(unsigned int dev_id)
>>   {
>> +#ifdef CPU_HAS_H32MXDIV
>> +	return get_mck_clk_rate() / H32MXDIV;
>> +#else
>>   	return get_mck_clk_rate();
>> +#endif
>>   }
>>
>>   static inline unsigned long get_twi_clk_rate(unsigned int dev_id)
>>   {
>> +#ifdef CPU_HAS_H32MXDIV
>> +	return get_mck_clk_rate() / H32MXDIV;
>> +#else
>>   	return get_mck_clk_rate();
>> +#endif
>>   }
>>
>>   static inline unsigned long get_mci_clk_rate(void)
>>   {
>> +#ifdef CPU_HAS_H32MXDIV
>> +	return get_mck_clk_rate() / H32MXDIV;
>> +#else
>>   	return get_mck_clk_rate();
>> +#endif
>> +}
>> +
>> +static inline unsigned long get_pit_clk_rate(void)
>> +{
>> +#ifdef CPU_HAS_H32MXDIV
>> +	return get_mck_clk_rate() / H32MXDIV;
>> +#else
>> +	return get_mck_clk_rate();
>> +#endif
>>   }
>>
>>   int at91_clock_init(unsigned long main_clock);
>> diff --git a/arch/arm/include/asm/arch-at91/hardware.h b/arch/arm/include/asm/arch-at91/hardware.h
>> index d712a0d..bf0a1bd 100644
>> --- a/arch/arm/include/asm/arch-at91/hardware.h
>> +++ b/arch/arm/include/asm/arch-at91/hardware.h
>> @@ -27,6 +27,8 @@
>>   # include <asm/arch/at91cap9.h>
>>   #elif defined(CONFIG_SAMA5D3)
>>   # include <asm/arch/sama5d3.h>
>> +#elif defined(CONFIG_SAMA5D4)
>> +# include <asm/arch/sama5d4.h>
>>   #else
>>   # error "Unsupported AT91 processor"
>>   #endif
>> diff --git a/arch/arm/include/asm/arch-at91/sama5d4.h b/arch/arm/include/asm/arch-at91/sama5d4.h
>> new file mode 100644
>> index 0000000..12a6646
>> --- /dev/null
>> +++ b/arch/arm/include/asm/arch-at91/sama5d4.h
>> @@ -0,0 +1,199 @@
>> +/*
>> + * Chip-specific header file for the SAMA5D4 SoC
>> + *
>> + * Copyright (C) 2014 Atmel
>> + *		      Bo Shen <voice.shen@atmel.com>
>> + *
>> + * SPDX-License-Identifier:     GPL-2.0+
>> + */
>> +
>> +#ifndef __SAMA5D4_H
>> +#define __SAMA5D4_H
>> +
>> +/*
>> + * defines to be used in other places
>> + */
>> +#define CONFIG_ARMV7		/* ARM Cortex-A5 Core */
>> +#define CONFIG_AT91FAMILY	/* It's a member of AT91 */
>
> We should start moving these defines into Kconfig ... someday

That's a good idea.

>> +
>> +/*
>> + * Peripheral identifiers/interrupts.
>> + */
>> +#define ATMEL_ID_FIQ	0	/* FIQ Interrupt */
>> +#define ATMEL_ID_SYS	1	/* System Controller */
>> +#define ATMEL_ID_ARM	2	/* Performance Monitor Unit */
>> +#define ATMEL_ID_PIT	3	/* Periodic Interval Timer */
>> +#define ATMEL_ID_WDT	4	/* Watchdog timer */
>> +#define ATMEL_ID_PIOD	5	/* Parallel I/O Controller D */
>> +#define ATMEL_ID_USART0	6	/* USART 0 */
>> +#define ATMEL_ID_USART1	7	/* USART 1 */
>> +#define ATMEL_ID_DMA0	8	/* DMA Controller 0 */
>> +#define ATMEL_ID_ICM	9	/* Integrity Check Monitor */
>> +#define ATMEL_ID_PKCC	10	/* Public Key Crypto Controller */
>> +#define ATMEL_ID_AES	12	/* Advanced Encryption Standard */
>> +#define ATMEL_ID_AESB	13	/* AES Bridge*/
>> +#define ATMEL_ID_TDES	14	/* Triple Data Encryption Standard */
>> +#define ATMEL_ID_SHA    15	/* SHA Signature */
>> +#define ATMEL_ID_MPDDRC	16	/* MPDDR controller */
>> +#define ATMEL_ID_MATRIX1	17	/* H32MX, 32-bit AHB Matrix */
>> +#define ATMEL_ID_MATRIX0	18	/* H64MX, 64-bit AHB Matrix */
>> +#define ATMEL_ID_VDEC	19	/* Video Decoder */
>> +#define ATMEL_ID_SBM	20	/* Secure Box Module */
>> +#define ATMEL_ID_SMC	22	/* Multi-bit ECC interrupt */
>> +#define ATMEL_ID_PIOA	23	/* Parallel I/O Controller A */
>> +#define ATMEL_ID_PIOB	24	/* Parallel I/O Controller B */
>> +#define ATMEL_ID_PIOC	25	/* Parallel I/O Controller C */
>> +#define ATMEL_ID_PIOE	26	/* Parallel I/O Controller E */
>> +#define ATMEL_ID_UART0	27	/* UART 0 */
>> +#define ATMEL_ID_UART1	28	/* UART 1 */
>> +#define ATMEL_ID_USART2	29	/* USART 2 */
>> +#define ATMEL_ID_USART3	30	/* USART 3 */
>> +#define ATMEL_ID_USART4	31	/* USART 4 */
>> +#define ATMEL_ID_TWI0	32	/* Two-Wire Interface 0 */
>> +#define ATMEL_ID_TWI1	33	/* Two-Wire Interface 1 */
>> +#define ATMEL_ID_TWI2	34	/* Two-Wire Interface 2 */
>> +#define ATMEL_ID_MCI0	35	/* High Speed Multimedia Card Interface 0 */
>> +#define ATMEL_ID_MCI1	36	/* High Speed Multimedia Card Interface 1 */
>> +#define ATMEL_ID_SPI0	37	/* Serial Peripheral Interface 0 */
>> +#define ATMEL_ID_SPI1	38	/* Serial Peripheral Interface 1 */
>> +#define ATMEL_ID_SPI2	39	/* Serial Peripheral Interface 2 */
>> +#define ATMEL_ID_TC0	40	/* Timer Counter 0 (ch. 0, 1, 2) */
>> +#define ATMEL_ID_TC1	41	/* Timer Counter 1 (ch. 3, 4, 5) */
>> +#define ATMEL_ID_TC2	42	/* Timer Counter 2 (ch. 6, 7, 8) */
>> +#define ATMEL_ID_PWMC	43	/* Pulse Width Modulation Controller */
>> +#define ATMEL_ID_ADC	44	/* Touch Screen ADC Controller */
>> +#define ATMEL_ID_DBGU	45	/* Debug Unit Interrupt */
>> +#define ATMEL_ID_UHPHS	46	/* USB Host High Speed */
>> +#define ATMEL_ID_UDPHS	47	/* USB Device High Speed */
>> +#define ATMEL_ID_SSC0	48	/* Synchronous Serial Controller 0 */
>> +#define ATMEL_ID_SSC1	49	/* Synchronous Serial Controller 1 */
>> +#define ATMEL_ID_XDMAC1	50	/* DMA Controller 1 */
>> +#define ATMEL_ID_LCDC	51	/* LCD Controller */
>> +#define ATMEL_ID_ISI	52	/* Image Sensor Interface */
>> +#define ATMEL_ID_TRNG	53	/* True Random Number Generator */
>> +#define ATMEL_ID_GMAC0	54	/* Ethernet MAC 0 */
>> +#define ATMEL_ID_GMAC1	55	/* Ethernet MAC 1 */
>> +#define ATMEL_ID_IRQ	56	/* IRQ Interrupt ID */
>> +#define ATMEL_ID_SFC	57	/* Fuse Controller */
>> +#define ATMEL_ID_SECURAM	59	/* Secured RAM */
>> +#define ATMEL_ID_SMD	61	/* SMD Soft Modem */
>> +#define ATMEL_ID_TWI3	62	/* Two-Wire Interface 3 */
>> +#define ATMEL_ID_CATB	63	/* Capacitive Touch Controller */
>> +#define ATMEL_ID_SFR	64	/* Special Funcion Register */
>> +#define ATMEL_ID_AIC	65	/* Advanced Interrupt Controller */
>> +#define ATMEL_ID_SAIC	66	/* Secured Advanced Interrupt Controller */
>> +#define ATMEL_ID_L2CC	67	/* L2 Cache Controller */
>> +
>> +/*
>> + * User Peripherals physical base addresses.
>> + */
>> +#define ATMEL_BASE_LCDC		0xf0000000
>> +#define ATMEL_BASE_DMAC1	0xf0004000
>> +#define ATMEL_BASE_ISI		0xf0008000
>> +#define ATMEL_BASE_PKCC		0xf000C000
>> +#define ATMEL_BASE_MPDDRC	0xf0010000
>> +#define ATMEL_BASE_DMAC0	0xf0014000
>> +#define ATMEL_BASE_PMC		0xf0018000
>> +#define ATMEL_BASE_MATRIX0	0xf001c000
>> +#define ATMEL_BASE_AESB		0xf0020000
>> +/* Reserved: 0xf0024000 - 0xf8000000 */
>> +#define ATMEL_BASE_MCI0		0xf8000000
>> +#define ATMEL_BASE_UART0	0xf8004000
>> +#define ATMEL_BASE_SSC0		0xf8008000
>> +#define ATMEL_BASE_PWMC		0xf800c000
>> +#define ATMEL_BASE_SPI0		0xf8010000
>> +#define ATMEL_BASE_TWI0		0xf8014000
>> +#define ATMEL_BASE_TWI1		0xf8018000
>> +#define ATMEL_BASE_TC0		0xf801c000
>> +#define ATMEL_BASE_GMAC0	0xf8020000
>> +#define ATMEL_BASE_TWI2		0xf8024000
>> +#define ATMEL_BASE_SFR		0xf8028000
>> +#define ATMEL_BASE_USART0	0xf802c000
>> +#define ATMEL_BASE_USART1	0xf8030000
>> +/* Reserved:	0xf8034000 - 0xfc000000 */
>> +#define ATMEL_BASE_MCI1		0xfc000000
>> +#define ATMEL_BASE_UART1	0xfc004000
>> +#define ATMEL_BASE_USART2	0xfc008000
>> +#define ATMEL_BASE_USART3	0xfc00c000
>> +#define ATMEL_BASE_USART4	0xfc010000
>> +#define ATMEL_BASE_SSC1		0xfc014000
>> +#define ATMEL_BASE_SPI1		0xfc018000
>> +#define ATMEL_BASE_SPI2		0xfc01c000
>> +#define ATMEL_BASE_TC1		0xfc020000
>> +#define ATMEL_BASE_TC2		0xfc024000
>> +#define ATMEL_BASE_GMAC1	0xfc028000
>> +#define ATMEL_BASE_UDPHS	0xfc02c000
>> +#define ATMEL_BASE_TRNG		0xfc030000
>> +#define ATMEL_BASE_ADC		0xfc034000
>> +#define ATMEL_BASE_TWI3		0xfc038000
>> +
>> +#define ATMEL_BASE_SMC		0xfc05c000
>> +#define ATMEL_BASE_PMECC	(ATMEL_BASE_SMC + 0x070)
>> +#define ATMEL_BASE_PMERRLOC	(ATMEL_BASE_SMC + 0x500)
>> +
>> +#define ATMEL_BASE_PIOD		0xfc068000
>> +#define ATMEL_BASE_RSTC		0xfc068600
>> +#define ATMEL_BASE_PIT		0xfc068630
>> +#define ATMEL_BASE_WDT		0xfc068640
>> +
>> +#define ATMEL_BASE_DBGU		0xfc069000
>> +#define ATMEL_BASE_PIOA		0xfc06a000
>> +#define ATMEL_BASE_PIOB		0xfc06b000
>> +#define ATMEL_BASE_PIOC		0xfc06c000
>> +#define ATMEL_BASE_PIOE		0xfc06d000
>> +#define ATMEL_BASE_AIC		0xfc06e000
>> +
>> +/*
>> + * Internal Memory.
>> + */
>> +#define ATMEL_BASE_ROM		0x00000000	/* Internal ROM base address */
>> +#define ATMEL_BASE_NFC		0x00100000	/* NFC SRAM */
>> +#define ATMEL_BASE_SRAM		0x00200000	/* Internal ROM base address */
>> +#define ATMEL_BASE_VDEC		0x00300000	/* Video Decoder Controller */
>> +#define ATMEL_BASE_UDPHS_FIFO	0x00400000	/* USB Device HS controller */
>> +#define ATMEL_BASE_OHCI		0x00500000	/* USB Host controller (OHCI) */
>> +#define ATMEL_BASE_EHCI		0x00600000	/* USB Host controller (EHCI) */
>> +#define ATMEL_BASE_AXI		0x00700000
>> +#define ATMEL_BASE_DAP		0x00800000
>> +#define ATMEL_BASE_SMD		0x00900000
>> +
>> +/*
>> + * External memory
>> + */
>> +#define ATMEL_BASE_CS0		0x10000000
>> +#define ATMEL_BASE_DDRCS	0x20000000
>> +#define ATMEL_BASE_CS1		0x60000000
>> +#define ATMEL_BASE_CS2		0x70000000
>> +#define ATMEL_BASE_CS3		0x80000000
>> +
>> +/*
>> + * Other misc defines
>> + */
>> +#define ATMEL_PIO_PORTS		5
>> +#define CPU_HAS_PIO3
>> +#define PIO_SCDR_DIV		0x3fff
>> +#define CPU_HAS_PCR
>> +#define CPU_HAS_H32MXDIV
>> +
>> +/*
>> + * The clock of peripheral connect to H32MX is decided by H32MXDIV
>> + * bit in MCKR, if this bit is set, the peripheral only work at half
>> + * of MCK, the MCKR address is 0xf0018030, and H32MXDIV is bit 24.
>> + */
>> +#define H32MXDIV	(readl(0xF0018030) & (1 << 24) ? 2 : 1)
>
> Could we use ATMEL_BASE_PMC + <some new define> here?

Yes. I will add it.

>> +
>> +/*
>> + * No PMECC Galois table in ROM
>> + */
>> +#define NO_GALOIS_TABLE_IN_ROM
>> +
>> +#ifndef __ASSEMBLY__
>> +unsigned int get_chip_id(void);
>> +unsigned int get_extension_chip_id(void);
>> +unsigned int has_emac(void);
>> +unsigned int has_gmac(void);
>> +unsigned int has_lcdc(void);
>> +char *get_cpu_name(void);
>> +#endif
>> +
>> +#endif
>> diff --git a/board/atmel/sama5d4ek/Kconfig b/board/atmel/sama5d4ek/Kconfig
>> new file mode 100644
>> index 0000000..a889895
>> --- /dev/null
>> +++ b/board/atmel/sama5d4ek/Kconfig
>> @@ -0,0 +1,18 @@
>> +if TARGET_SAMA5D4EK
>> +
>> +config SYS_CPU
>> +	default "armv7"
>> +
>> +config SYS_BOARD
>> +	default "sama5d4ek"
>> +
>> +config SYS_VENDOR
>> +	default "atmel"
>> +
>> +config SYS_SOC
>> +	default "at91"
>> +
>> +config SYS_CONFIG_NAME
>> +	default "sama5d4ek"
>> +
>> +endif
>> diff --git a/board/atmel/sama5d4ek/MAINTAINERS b/board/atmel/sama5d4ek/MAINTAINERS
>> new file mode 100644
>> index 0000000..afe88dd
>> --- /dev/null
>> +++ b/board/atmel/sama5d4ek/MAINTAINERS
>> @@ -0,0 +1,8 @@
>> +SAMA5D4EK BOARD
>> +M:	Bo Shen <voice.shen@atmel.com>
>> +S:	Maintained
>> +F:	board/atmel/sama5d4ek/
>> +F:	include/configs/sama5d4ek.h
>> +F:	configs/sama5d4ek_mmc_defconfig
>> +F:	configs/sama5d4ek_nandflash_defconfig
>> +F:	configs/sama5d4ek_spiflash_defconfig
>> diff --git a/board/atmel/sama5d4ek/Makefile b/board/atmel/sama5d4ek/Makefile
>> new file mode 100644
>> index 0000000..d91525c
>> --- /dev/null
>> +++ b/board/atmel/sama5d4ek/Makefile
>> @@ -0,0 +1,15 @@
>> +#
>> +# (C) Copyright 2003-2008
>> +# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
>> +#
>> +# (C) Copyright 2008
>> +# Stelian Pop <stelian@popies.net>
>> +# Lead Tech Design <www.leadtechdesign.com>
>> +#
>> +# (C) Copyright 2014
>> +# Bo Shen <voice.shen@atmel.com>
>> +#
>> +# SPDX-License-Identifier:	GPL-2.0+
>> +#
>> +
>> +obj-y += sama5d4ek.o
>> diff --git a/board/atmel/sama5d4ek/sama5d4ek.c b/board/atmel/sama5d4ek/sama5d4ek.c
>> new file mode 100644
>> index 0000000..099b924
>> --- /dev/null
>> +++ b/board/atmel/sama5d4ek/sama5d4ek.c
>> @@ -0,0 +1,322 @@
>> +/*
>> + * Copyright (C) 2014 Atmel
>> + *		      Bo Shen <voice.shen@atmel.com>
>> + *
>> + * SPDX-License-Identifier:	GPL-2.0+
>> + */
>> +
>> +#include <common.h>
>> +#include <asm/io.h>
>> +#include <asm/arch/at91_common.h>
>> +#include <asm/arch/at91_pmc.h>
>> +#include <asm/arch/at91_rstc.h>
>> +#include <asm/arch/gpio.h>
>> +#include <asm/arch/clk.h>
>> +#include <asm/arch/sama5d3_smc.h>
>> +#include <asm/arch/sama5d4.h>
>> +#include <atmel_lcdc.h>
>> +#include <atmel_mci.h>
>> +#include <lcd.h>
>> +#include <mmc.h>
>> +#include <net.h>
>> +#include <netdev.h>
>> +#include <nand.h>
>> +#include <spi.h>
>> +
>> +DECLARE_GLOBAL_DATA_PTR;
>> +
>> +#ifdef CONFIG_ATMEL_SPI
>> +int spi_cs_is_valid(unsigned int bus, unsigned int cs)
>> +{
>> +	return bus == 0 && cs == 0;
>> +}
>> +
>> +void spi_cs_activate(struct spi_slave *slave)
>> +{
>> +	at91_set_pio_output(AT91_PIO_PORTC, 3, 0);
>> +}
>> +
>> +void spi_cs_deactivate(struct spi_slave *slave)
>> +{
>> +	at91_set_pio_output(AT91_PIO_PORTC, 3, 1);
>> +}
>> +
>> +static void sama5d4ek_spi0_hw_init(void)
>> +{
>> +	at91_set_a_periph(AT91_PIO_PORTC, 0, 0);	/* SPI0_MISO */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 1, 0);	/* SPI0_MOSI */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 2, 0);	/* SPI0_SPCK */
>> +
>> +	at91_set_pio_output(AT91_PIO_PORTC, 3, 1);	/* SPI0_CS0 */
>> +
>> +	/* Enable clock */
>> +	at91_periph_clk_enable(ATMEL_ID_SPI0);
>> +}
>> +#endif /* CONFIG_ATMEL_SPI */
>> +
>> +#ifdef CONFIG_NAND_ATMEL
>> +static void sama5d4ek_nand_hw_init(void)
>> +{
>> +	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
>> +
>> +	at91_periph_clk_enable(ATMEL_ID_SMC);
>> +
>> +	/* Configure SMC CS3 for NAND */
>> +	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) |
>> +	       AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(1),
>> +	       &smc->cs[3].setup);
>> +	writel(AT91_SMC_PULSE_NWE(2) | AT91_SMC_PULSE_NCS_WR(3) |
>> +	       AT91_SMC_PULSE_NRD(2) | AT91_SMC_PULSE_NCS_RD(3),
>> +	       &smc->cs[3].pulse);
>> +	writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
>> +	       &smc->cs[3].cycle);
>> +	writel(AT91_SMC_TIMINGS_TCLR(2) | AT91_SMC_TIMINGS_TADL(7) |
>> +	       AT91_SMC_TIMINGS_TAR(2)  | AT91_SMC_TIMINGS_TRR(3)   |
>> +	       AT91_SMC_TIMINGS_TWB(7)  | AT91_SMC_TIMINGS_RBNSEL(3)|
>> +	       AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings);
>> +	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
>> +	       AT91_SMC_MODE_EXNW_DISABLE |
>> +	       AT91_SMC_MODE_DBW_8 |
>> +	       AT91_SMC_MODE_TDF_CYCLE(3),
>> +	       &smc->cs[3].mode);
>> +
>> +	at91_set_a_periph(AT91_PIO_PORTC, 5, 0);	/* D0 */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 6, 0);	/* D1 */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 7, 0);	/* D2 */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 8, 0);	/* D3 */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 9, 0);	/* D4 */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 10, 0);	/* D5 */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 11, 0);	/* D6 */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 12, 0);	/* D7 */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 13, 0);	/* RE */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 14, 0);	/* WE */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 15, 1);	/* NCS */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 16, 1);	/* RDY */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 17, 1);	/* ALE */
>> +	at91_set_a_periph(AT91_PIO_PORTC, 18, 1);	/* CLE */
>> +}
>> +#endif
>> +
>> +#ifdef CONFIG_CMD_USB
>> +static void sama5d4ek_usb_hw_init(void)
>> +{
>> +	at91_set_pio_output(AT91_PIO_PORTE, 11, 0);
>> +	at91_set_pio_output(AT91_PIO_PORTE, 12, 0);
>> +	at91_set_pio_output(AT91_PIO_PORTE, 10, 0);
>> +}
>> +#endif
>> +
>> +#ifdef CONFIG_LCD
>> +vidinfo_t panel_info = {
>> +	.vl_col = 800,
>> +	.vl_row = 480,
>> +	.vl_clk = 33260000,
>> +	.vl_sync = ATMEL_LCDC_INVLINE_NORMAL | ATMEL_LCDC_INVFRAME_NORMAL,
>> +	.vl_bpix = LCD_BPP,
>> +	.vl_tft = 1,
>> +	.vl_hsync_len = 5,
>> +	.vl_left_margin = 128,
>> +	.vl_right_margin = 0,
>> +	.vl_vsync_len = 5,
>> +	.vl_upper_margin = 23,
>> +	.vl_lower_margin = 22,
>> +	.mmio = ATMEL_BASE_LCDC,
>> +};
>> +
>> +/* No power up/down pin for the LCD pannel */
>> +void lcd_enable(void)	{ /* Empty! */ }
>> +void lcd_disable(void)	{ /* Empty! */ }
>> +
>> +unsigned int has_lcdc(void)
>> +{
>> +	return 1;
>> +}
>> +
>> +static void sama5d4ek_lcd_hw_init(void)
>> +{
>> +	at91_set_a_periph(AT91_PIO_PORTA, 24, 0);	/* LCDPWM */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 25, 0);	/* LCDDISP */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 26, 0);	/* LCDVSYNC */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 27, 0);	/* LCDHSYNC */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 28, 0);	/* LCDDOTCK */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 29, 0);	/* LCDDEN */
>> +
>> +	at91_set_a_periph(AT91_PIO_PORTA,  2, 0);	/* LCDD2 */
>> +	at91_set_a_periph(AT91_PIO_PORTA,  3, 0);	/* LCDD3 */
>> +	at91_set_a_periph(AT91_PIO_PORTA,  4, 0);	/* LCDD4 */
>> +	at91_set_a_periph(AT91_PIO_PORTA,  5, 0);	/* LCDD5 */
>> +	at91_set_a_periph(AT91_PIO_PORTA,  6, 0);	/* LCDD6 */
>> +	at91_set_a_periph(AT91_PIO_PORTA,  7, 0);	/* LCDD7 */
>> +
>> +	at91_set_a_periph(AT91_PIO_PORTA, 10, 0);	/* LCDD10 */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 11, 0);	/* LCDD11 */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 12, 0);	/* LCDD12 */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 13, 0);	/* LCDD13 */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 14, 0);	/* LCDD14 */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 15, 0);	/* LCDD15 */
>> +
>> +	at91_set_a_periph(AT91_PIO_PORTA, 18, 0);	/* LCDD18 */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 19, 0);	/* LCDD19 */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 20, 0);	/* LCDD20 */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 21, 0);	/* LCDD21 */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 22, 0);	/* LCDD22 */
>> +	at91_set_a_periph(AT91_PIO_PORTA, 23, 0);	/* LCDD23 */
>> +
>> +	/* Enable clock */
>> +	at91_periph_clk_enable(ATMEL_ID_LCDC);
>> +}
>> +
>> +#ifdef CONFIG_LCD_INFO
>> +void lcd_show_board_info(void)
>> +{
>> +	ulong dram_size, nand_size;
>> +	int i;
>> +	char temp[32];
>> +
>> +	lcd_printf("2014 ATMEL Corp\n");
>> +	lcd_printf("at91@atmel.com\n");
>> +	lcd_printf("%s CPU at %s MHz\n", get_cpu_name(),
>> +		   strmhz(temp, get_cpu_clk_rate()));
>> +
>> +	dram_size = 0;
>> +	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
>> +		dram_size += gd->bd->bi_dram[i].size;
>> +
>> +	nand_size = 0;
>> +#ifdef CONFIG_NAND_ATMEL
>> +	for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
>> +		nand_size += nand_info[i].size;
>> +#endif
>> +	lcd_printf("%ld MB SDRAM, %ld MB NAND\n",
>> +		   dram_size >> 20, nand_size >> 20);
>> +}
>> +#endif /* CONFIG_LCD_INFO */
>> +
>> +#endif /* CONFIG_LCD */
>> +
>> +#ifdef CONFIG_GENERIC_ATMEL_MCI
>> +void sama5d4ek_mci1_hw_init(void)
>> +{
>> +	at91_set_c_periph(AT91_PIO_PORTE, 19, 1);	/* MCI1 CDA */
>> +	at91_set_c_periph(AT91_PIO_PORTE, 20, 1);	/* MCI1 DA0 */
>> +	at91_set_c_periph(AT91_PIO_PORTE, 21, 1);	/* MCI1 DA1 */
>> +	at91_set_c_periph(AT91_PIO_PORTE, 22, 1);	/* MCI1 DA2 */
>> +	at91_set_c_periph(AT91_PIO_PORTE, 23, 1);	/* MCI1 DA3 */
>> +	at91_set_c_periph(AT91_PIO_PORTE, 18, 0);	/* MCI1 CLK */
>> +
>> +	/*
>> +	 * As the mci io internal pull down is too strong, so if the io needs
>> +	 * external pull up, the pull up resistor will be very small, if so
>> +	 * the power consumption will increase, so disable the interanl pull
>> +	 * down to save the power.
>> +	 */
>> +	at91_set_pio_pulldown(AT91_PIO_PORTE, 18, 0);
>> +	at91_set_pio_pulldown(AT91_PIO_PORTE, 19, 0);
>> +	at91_set_pio_pulldown(AT91_PIO_PORTE, 20, 0);
>> +	at91_set_pio_pulldown(AT91_PIO_PORTE, 21, 0);
>> +	at91_set_pio_pulldown(AT91_PIO_PORTE, 22, 0);
>> +	at91_set_pio_pulldown(AT91_PIO_PORTE, 23, 0);
>> +
>> +	/* Enable clock */
>> +	at91_periph_clk_enable(ATMEL_ID_MCI1);
>> +}
>> +
>> +int board_mmc_init(bd_t *bis)
>> +{
>> +	/* Enable power for MCI1 interface */
>> +	at91_set_pio_output(AT91_PIO_PORTE, 15, 0);
>> +
>> +	return atmel_mci_init((void *)ATMEL_BASE_MCI1);
>> +}
>> +#endif /* CONFIG_GENERIC_ATMEL_MCI */
>> +
>> +#ifdef CONFIG_MACB
>> +void sama5d4ek_macb0_hw_init(void)
>> +{
>> +	at91_set_a_periph(AT91_PIO_PORTB, 0, 0);	/* ETXCK_EREFCK */
>> +	at91_set_a_periph(AT91_PIO_PORTB, 6, 0);	/* ERXDV */
>> +	at91_set_a_periph(AT91_PIO_PORTB, 8, 0);	/* ERX0 */
>> +	at91_set_a_periph(AT91_PIO_PORTB, 9, 0);	/* ERX1 */
>> +	at91_set_a_periph(AT91_PIO_PORTB, 7, 0);	/* ERXER */
>> +	at91_set_a_periph(AT91_PIO_PORTB, 2, 0);	/* ETXEN */
>> +	at91_set_a_periph(AT91_PIO_PORTB, 12, 0);	/* ETX0 */
>> +	at91_set_a_periph(AT91_PIO_PORTB, 13, 0);	/* ETX1 */
>> +	at91_set_a_periph(AT91_PIO_PORTB, 17, 0);	/* EMDIO */
>> +	at91_set_a_periph(AT91_PIO_PORTB, 16, 0);	/* EMDC */
>> +
>> +	/* Enable clock */
>> +	at91_periph_clk_enable(ATMEL_ID_GMAC0);
>> +}
>> +#endif
>> +
>> +char *get_cpu_name()
>> +{
>> +	return "SAMA5D4";
>> +}
>
> Since when is the get_cpu_name() a board function? This should be placed

This should be a SoC function and in SoC file.

> in some SoC file. Generally I'm missing a sama5d4_devices.c There should
> be placed some of the functions here in the board code.

As the SoC before SAMA5D4 which has pins can not be mux, so we put this 
part of code in SoC file (<soc_name>_device.c), however on SAMA5D4 SoC, 
almost can not find the pin can not be mux, so, I don't keep the 
sama5d4_device.c file.

>> +
>> +static void sama5d4ek_serial3_hw_init(void)
>> +{
>> +	at91_set_b_periph(AT91_PIO_PORTE, 17, 1);	/* TXD3 */
>> +	at91_set_b_periph(AT91_PIO_PORTE, 16, 0);	/* RXD3 */
>> +
>> +	/* Enable clock */
>> +	at91_periph_clk_enable(ATMEL_ID_USART3);
>> +}
>> +
>> +int board_early_init_f(void)
>> +{
>> +	at91_periph_clk_enable(ATMEL_ID_PIOA);
>> +	at91_periph_clk_enable(ATMEL_ID_PIOB);
>> +	at91_periph_clk_enable(ATMEL_ID_PIOC);
>> +	at91_periph_clk_enable(ATMEL_ID_PIOD);
>> +	at91_periph_clk_enable(ATMEL_ID_PIOE);
>> +
>> +	sama5d4ek_serial3_hw_init();
>> +
>> +	return 0;
>> +}
>> +
>> +int board_init(void)
>> +{
>> +	/* adress of boot parameters */
>> +	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
>> +
>> +#ifdef CONFIG_ATMEL_SPI
>> +	sama5d4ek_spi0_hw_init();
>> +#endif
>> +#ifdef CONFIG_NAND_ATMEL
>> +	sama5d4ek_nand_hw_init();
>> +#endif
>> +#ifdef CONFIG_GENERIC_ATMEL_MCI
>> +	sama5d4ek_mci1_hw_init();
>> +#endif
>> +#ifdef CONFIG_MACB
>> +	sama5d4ek_macb0_hw_init();
>> +#endif
>> +#ifdef CONFIG_LCD
>> +	sama5d4ek_lcd_hw_init();
>> +#endif
>> +#ifdef CONFIG_CMD_USB
>> +	sama5d4ek_usb_hw_init();
>> +#endif
>> +
>> +	return 0;
>> +}
>> +
>> +int dram_init(void)
>> +{
>> +	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
>> +				    CONFIG_SYS_SDRAM_SIZE);
>> +	return 0;
>> +}
>> +
>> +int board_eth_init(bd_t *bis)
>> +{
>> +	int rc = 0;
>> +
>> +#ifdef CONFIG_MACB
>> +	rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00);
>> +#endif
>> +
>> +	return rc;
>> +}
>> diff --git a/configs/sama5d4ek_mmc_defconfig b/configs/sama5d4ek_mmc_defconfig
>> new file mode 100644
>> index 0000000..16a5ed7
>> --- /dev/null
>> +++ b/configs/sama5d4ek_mmc_defconfig
>> @@ -0,0 +1,3 @@
>> +CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_MMC"
>> ++S:CONFIG_ARM=y
>> ++S:CONFIG_TARGET_SAMA5D4EK=y
>> diff --git a/configs/sama5d4ek_nandflash_defconfig b/configs/sama5d4ek_nandflash_defconfig
>> new file mode 100644
>> index 0000000..8b7fbc3
>> --- /dev/null
>> +++ b/configs/sama5d4ek_nandflash_defconfig
>> @@ -0,0 +1,3 @@
>> +CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_NANDFLASH"
>> ++S:CONFIG_ARM=y
>> ++S:CONFIG_TARGET_SAMA5D4EK=y
>> diff --git a/configs/sama5d4ek_spiflash_defconfig b/configs/sama5d4ek_spiflash_defconfig
>> new file mode 100644
>> index 0000000..63e9b6c
>> --- /dev/null
>> +++ b/configs/sama5d4ek_spiflash_defconfig
>> @@ -0,0 +1,3 @@
>> +CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_SERIALFLASH"
>> ++S:CONFIG_ARM=y
>> ++S:CONFIG_TARGET_SAMA5D4EK=y
>> diff --git a/include/configs/sama5d4ek.h b/include/configs/sama5d4ek.h
>> new file mode 100644
>> index 0000000..d50897e
>> --- /dev/null
>> +++ b/include/configs/sama5d4ek.h
>> @@ -0,0 +1,215 @@
>> +/*
>> + * Configuration settings for the SAMA5D4EK board.
>> + *
>> + * Copyright (C) 2014 Atmel
>> + *		      Bo Shen <voice.shen@atmel.com>
>> + *
>> + * SPDX-License-Identifier:	GPL-2.0+
>> + */
>> +
>> +#ifndef __CONFIG_H
>> +#define __CONFIG_H
>> +
>> +#include <asm/hardware.h>
>> +
>> +#define CONFIG_SYS_TEXT_BASE		0x26f00000
>> +
>> +/* ARM asynchronous clock */
>> +#define CONFIG_SYS_AT91_SLOW_CLOCK      32768
>> +#define CONFIG_SYS_AT91_MAIN_CLOCK      12000000 /* from 12 MHz crystal */
>> +#define CONFIG_SYS_HZ		        1000
>> +
>> +#define CONFIG_ARCH_CPU_INIT
>> +
>> +#define CONFIG_SKIP_LOWLEVEL_INIT
>> +#define CONFIG_BOARD_EARLY_INIT_F
>> +#define CONFIG_DISPLAY_CPUINFO
>> +
>> +#define CONFIG_CMD_BOOTZ
>> +#define CONFIG_OF_LIBFDT		/* Device Tree support */
>> +
>> +#define CONFIG_SYS_GENERIC_BOARD
>> +
>> +/* general purpose I/O */
>> +#define CONFIG_AT91_GPIO
>> +
>> +/* serial console */
>> +#define CONFIG_ATMEL_USART
>> +#define CONFIG_USART_BASE		ATMEL_BASE_USART3
>> +#define	CONFIG_USART_ID			ATMEL_ID_USART3
>> +
>> +#define CONFIG_BOOTDELAY		3
>> +
>> +/*
>> + * BOOTP options
>> + */
>> +#define CONFIG_BOOTP_BOOTFILESIZE
>> +#define CONFIG_BOOTP_BOOTPATH
>> +#define CONFIG_BOOTP_GATEWAY
>> +#define CONFIG_BOOTP_HOSTNAME
>> +
>> +/* No NOR flash */
>> +#define CONFIG_SYS_NO_FLASH
>> +
>> +/*
>> + * Command line configuration.
>> + */
>> +#include <config_cmd_default.h>
>> +#undef CONFIG_CMD_FPGA
>> +#undef CONFIG_CMD_IMI
>> +#undef CONFIG_CMD_LOADS
>> +#define CONFIG_CMD_PING
>> +#define CONFIG_CMD_DHCP
>> +#define CONFIG_CMD_SETEXPR
>> +
>> +/* SDRAM */
>> +#define CONFIG_NR_DRAM_BANKS		1
>> +#define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
>> +#define CONFIG_SYS_SDRAM_SIZE		0x20000000
>> +
>> +#define CONFIG_SYS_INIT_SP_ADDR \
>> +	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
>> +
>> +#define CONFIG_SYS_LOAD_ADDR		0x22000000 /* load address */
>> +
>> +/* SerialFlash */
>> +#define CONFIG_CMD_SF
>> +
>> +#ifdef CONFIG_CMD_SF
>> +#define CONFIG_ATMEL_SPI
>> +#define CONFIG_ATMEL_SPI0
>> +#define CONFIG_SPI_FLASH
>> +#define CONFIG_SPI_FLASH_ATMEL
>> +#define CONFIG_SF_DEFAULT_BUS		0
>> +#define CONFIG_SF_DEFAULT_CS		0
>> +#define CONFIG_SF_DEFAULT_SPEED		30000000
>> +#endif
>> +
>> +/* NAND flash */
>> +#define CONFIG_CMD_NAND
>> +
>> +#ifdef CONFIG_CMD_NAND
>> +#define CONFIG_NAND_ATMEL
>> +#define CONFIG_SYS_MAX_NAND_DEVICE	1
>> +#define CONFIG_SYS_NAND_BASE		ATMEL_BASE_CS3
>> +/* our ALE is AD21 */
>> +#define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
>> +/* our CLE is AD22 */
>> +#define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
>> +#define CONFIG_SYS_NAND_ONFI_DETECTION
>> +/* PMECC & PMERRLOC */
>> +#define CONFIG_ATMEL_NAND_HWECC
>> +#define CONFIG_ATMEL_NAND_HW_PMECC
>> +#endif
>> +
>> +/* MMC */
>> +#define CONFIG_CMD_MMC
>> +
>> +#ifdef CONFIG_CMD_MMC
>> +#define CONFIG_MMC
>> +#define CONFIG_GENERIC_MMC
>> +#define CONFIG_GENERIC_ATMEL_MCI
>> +#define ATMEL_BASE_MMCI			ATMEL_BASE_MCI1
>> +#endif
>> +
>> +/* USB */
>> +#define CONFIG_CMD_USB
>> +
>> +#ifdef CONFIG_CMD_USB
>> +#define CONFIG_USB_EHCI
>> +#define CONFIG_USB_EHCI_ATMEL
>> +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	3
>> +#define CONFIG_USB_STORAGE
>> +#endif
>> +
>> +#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
>> +#define CONFIG_CMD_FAT
>> +#define CONFIG_DOS_PARTITION
>> +#endif
>> +
>> +/* Ethernet Hardware */
>> +#define CONFIG_MACB
>> +#define CONFIG_RMII
>> +#define CONFIG_NET_RETRY_COUNT		20
>> +#define CONFIG_MACB_SEARCH_PHY
>> +
>> +/* LCD */
>> +#define CONFIG_LCD
>> +#define LCD_BPP				LCD_COLOR16
>> +#define LCD_OUTPUT_BPP                  18
>> +#define CONFIG_LCD_LOGO
>> +#define CONFIG_LCD_INFO
>> +#define CONFIG_LCD_INFO_BELOW_LOGO
>> +#define CONFIG_SYS_WHITE_ON_BLACK
>> +#define CONFIG_ATMEL_HLCD
>> +#define CONFIG_ATMEL_LCD_RGB565
>> +#define CONFIG_SYS_CONSOLE_IS_IN_ENV
>> +
>> +#ifdef CONFIG_SYS_USE_SERIALFLASH
>> +/* bootstrap + u-boot + env + linux in serial flash */
>> +#define CONFIG_ENV_IS_IN_SPI_FLASH
>> +#define CONFIG_ENV_SPI_BUS	CONFIG_SF_DEFAULT_BUS
>> +#define CONFIG_ENV_SPI_CS	CONFIG_SF_DEFAULT_CS
>> +#define CONFIG_ENV_OFFSET       0x10000
>> +#define CONFIG_ENV_SIZE         0x10000
>> +#define CONFIG_ENV_SECT_SIZE    0x1000
>> +#define CONFIG_BOOTCOMMAND      "sf probe 0; " \
>> +				"sf read 0x21000000 0xa0000 0x60000; " \
>> +				"sf read 0x22000000 0x100000 0x300000; " \
>> +				"bootz 0x22000000 - 0x21000000"
>> +#elif CONFIG_SYS_USE_NANDFLASH
>> +/* bootstrap + u-boot + env in nandflash */
>> +#define CONFIG_ENV_IS_IN_NAND
>> +#define CONFIG_ENV_OFFSET		0xc0000
>> +#define CONFIG_ENV_OFFSET_REDUND	0x100000
>> +#define CONFIG_ENV_SIZE			0x20000
>> +#define CONFIG_BOOTCOMMAND	"nand read 0x21000000 0x180000 0x80000;" \
>> +				"nand read 0x22000000 0x200000 0x600000;" \
>> +				"bootz 0x22000000 - 0x21000000"
>> +#elif CONFIG_SYS_USE_MMC
>> +/* bootstrap + u-boot + env in sd card */
>> +#define CONFIG_ENV_IS_IN_FAT
>> +#define CONFIG_FAT_WRITE
>> +#define FAT_ENV_INTERFACE	"mmc"
>> +/*
>> + * We don't specify the part number, if device 0 has partition table, it means
>> + * the first partition; it no partition table, then take whole device as a
>> + * FAT file system.
>> + */
>> +#define FAT_ENV_DEVICE_AND_PART	"0"
>> +#define FAT_ENV_FILE		"uboot.env"
>> +#define CONFIG_ENV_SIZE		0x4000
>> +#define CONFIG_BOOTCOMMAND	"fatload mmc 0:1 0x21000000 sama5d4ek.dtb; " \
>> +				"fatload mmc 0:1 0x22000000 zImage; " \
>> +				"bootz 0x22000000 - 0x21000000"
>> +#endif
>> +
>> +#ifdef CONFIG_SYS_USE_MMC
>> +#define CONFIG_BOOTARGS							\
>> +	"console=ttyS0,115200 earlyprintk "				\
>> +	"root=/dev/mmcblk0p2 rw rootwait"
>> +#else
>> +#define CONFIG_BOOTARGS							\
>> +	"console=ttyS0,115200 earlyprintk "				\
>> +	"mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,"		\
>> +	"256K(env),256k(evn_redundent),256k(spare),"			\
>> +	"512k(dtb),6M(kernel)ro,-(rootfs) "				\
>> +	"rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs"
>> +#endif
>> +
>> +#define CONFIG_BAUDRATE			115200
>> +
>> +#define CONFIG_SYS_PROMPT		"U-Boot> "
>> +#define CONFIG_SYS_CBSIZE		256
>> +#define CONFIG_SYS_MAXARGS		16
>> +#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
>> +					sizeof(CONFIG_SYS_PROMPT) + 16)
>> +#define CONFIG_SYS_LONGHELP
>> +#define CONFIG_CMDLINE_EDITING
>> +#define CONFIG_AUTO_COMPLETE
>> +#define CONFIG_SYS_HUSH_PARSER
>> +
>> +/* Size of malloc() pool */
>> +#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
>> +
>> +#endif
>>
>
> Best Regards
>
> Andreas Bießmann
>

Best Regards,
Bo Shen
diff mbox

Patch

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index c8537bb..bbccd46 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -321,6 +321,9 @@  config TARGET_SAMA5D3_XPLAINED
 config TARGET_SAMA5D3XEK
 	bool "Support sama5d3xek"
 
+config TARGET_SAMA5D4EK
+	bool "Support sama5d4ek"
+
 config TARGET_BCM28155_AP
 	bool "Support bcm28155_ap"
 
@@ -569,6 +572,7 @@  source "board/atmel/at91sam9rlek/Kconfig"
 source "board/atmel/at91sam9x5ek/Kconfig"
 source "board/atmel/sama5d3_xplained/Kconfig"
 source "board/atmel/sama5d3xek/Kconfig"
+source "board/atmel/sama5d4ek/Kconfig"
 source "board/balloon3/Kconfig"
 source "board/barco/titanium/Kconfig"
 source "board/bluegiga/apx4devkit/Kconfig"
diff --git a/arch/arm/cpu/armv7/at91/timer.c b/arch/arm/cpu/armv7/at91/timer.c
index e3ebfe0..19bf80b 100644
--- a/arch/arm/cpu/armv7/at91/timer.c
+++ b/arch/arm/cpu/armv7/at91/timer.c
@@ -65,7 +65,8 @@  int timer_init(void)
 	/* Enable PITC */
 	writel(TIMER_LOAD_VAL | AT91_PIT_MR_EN , &pit->mr);
 
-	gd->arch.timer_rate_hz = gd->arch.mck_rate_hz / 16;
+	gd->arch.timer_rate_hz = get_pit_clk_rate() / 16;
+
 	gd->arch.tbu = 0;
 	gd->arch.tbl = 0;
 
diff --git a/arch/arm/include/asm/arch-at91/at91_pmc.h b/arch/arm/include/asm/arch-at91/at91_pmc.h
index 27331ff..e81ece9 100644
--- a/arch/arm/include/asm/arch-at91/at91_pmc.h
+++ b/arch/arm/include/asm/arch-at91/at91_pmc.h
@@ -78,7 +78,7 @@  typedef struct at91_pmc {
 #define AT91_PMC_PLLXR_DIV(x)		(x & 0xFF)
 #define AT91_PMC_PLLXR_PLLCOUNT(x)	((x & 0x3F) << 8)
 #define AT91_PMC_PLLXR_OUT(x)		((x & 0x03) << 14)
-#ifdef CONFIG_SAMA5D3
+#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
 #define AT91_PMC_PLLXR_MUL(x)		((x & 0x7F) << 18)
 #else
 #define AT91_PMC_PLLXR_MUL(x)		((x & 0x7FF) << 16)
@@ -97,7 +97,7 @@  typedef struct at91_pmc {
 #define AT91_PMC_MCKR_CSS_PLLB		0x00000003
 #define AT91_PMC_MCKR_CSS_MASK		0x00000003
 
-#ifdef CONFIG_SAMA5D3
+#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
 #define AT91_PMC_MCKR_PRES_1		0x00000000
 #define AT91_PMC_MCKR_PRES_2		0x00000010
 #define AT91_PMC_MCKR_PRES_4		0x00000020
@@ -126,7 +126,7 @@  typedef struct at91_pmc {
 #else
 #define AT91_PMC_MCKR_MDIV_1		0x00000000
 #define AT91_PMC_MCKR_MDIV_2		0x00000100
-#ifdef CONFIG_SAMA5D3
+#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
 #define AT91_PMC_MCKR_MDIV_3		0x00000300
 #endif
 #define AT91_PMC_MCKR_MDIV_4		0x00000200
diff --git a/arch/arm/include/asm/arch-at91/clk.h b/arch/arm/include/asm/arch-at91/clk.h
index 4076a78..7615018 100644
--- a/arch/arm/include/asm/arch-at91/clk.h
+++ b/arch/arm/include/asm/arch-at91/clk.h
@@ -50,12 +50,20 @@  static inline u32 get_pllb_init(void)
 
 static inline unsigned long get_macb_pclk_rate(unsigned int dev_id)
 {
+#ifdef CPU_HAS_H32MXDIV
+	return get_mck_clk_rate() / H32MXDIV;
+#else
 	return get_mck_clk_rate();
+#endif
 }
 
 static inline unsigned long get_usart_clk_rate(unsigned int dev_id)
 {
+#ifdef CPU_HAS_H32MXDIV
+	return get_mck_clk_rate() / H32MXDIV;
+#else
 	return get_mck_clk_rate();
+#endif
 }
 
 static inline unsigned long get_lcdc_clk_rate(unsigned int dev_id)
@@ -65,17 +73,38 @@  static inline unsigned long get_lcdc_clk_rate(unsigned int dev_id)
 
 static inline unsigned long get_spi_clk_rate(unsigned int dev_id)
 {
+#ifdef CPU_HAS_H32MXDIV
+	return get_mck_clk_rate() / H32MXDIV;
+#else
 	return get_mck_clk_rate();
+#endif
 }
 
 static inline unsigned long get_twi_clk_rate(unsigned int dev_id)
 {
+#ifdef CPU_HAS_H32MXDIV
+	return get_mck_clk_rate() / H32MXDIV;
+#else
 	return get_mck_clk_rate();
+#endif
 }
 
 static inline unsigned long get_mci_clk_rate(void)
 {
+#ifdef CPU_HAS_H32MXDIV
+	return get_mck_clk_rate() / H32MXDIV;
+#else
 	return get_mck_clk_rate();
+#endif
+}
+
+static inline unsigned long get_pit_clk_rate(void)
+{
+#ifdef CPU_HAS_H32MXDIV
+	return get_mck_clk_rate() / H32MXDIV;
+#else
+	return get_mck_clk_rate();
+#endif
 }
 
 int at91_clock_init(unsigned long main_clock);
diff --git a/arch/arm/include/asm/arch-at91/hardware.h b/arch/arm/include/asm/arch-at91/hardware.h
index d712a0d..bf0a1bd 100644
--- a/arch/arm/include/asm/arch-at91/hardware.h
+++ b/arch/arm/include/asm/arch-at91/hardware.h
@@ -27,6 +27,8 @@ 
 # include <asm/arch/at91cap9.h>
 #elif defined(CONFIG_SAMA5D3)
 # include <asm/arch/sama5d3.h>
+#elif defined(CONFIG_SAMA5D4)
+# include <asm/arch/sama5d4.h>
 #else
 # error "Unsupported AT91 processor"
 #endif
diff --git a/arch/arm/include/asm/arch-at91/sama5d4.h b/arch/arm/include/asm/arch-at91/sama5d4.h
new file mode 100644
index 0000000..12a6646
--- /dev/null
+++ b/arch/arm/include/asm/arch-at91/sama5d4.h
@@ -0,0 +1,199 @@ 
+/*
+ * Chip-specific header file for the SAMA5D4 SoC
+ *
+ * Copyright (C) 2014 Atmel
+ *		      Bo Shen <voice.shen@atmel.com>
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#ifndef __SAMA5D4_H
+#define __SAMA5D4_H
+
+/*
+ * defines to be used in other places
+ */
+#define CONFIG_ARMV7		/* ARM Cortex-A5 Core */
+#define CONFIG_AT91FAMILY	/* It's a member of AT91 */
+
+/*
+ * Peripheral identifiers/interrupts.
+ */
+#define ATMEL_ID_FIQ	0	/* FIQ Interrupt */
+#define ATMEL_ID_SYS	1	/* System Controller */
+#define ATMEL_ID_ARM	2	/* Performance Monitor Unit */
+#define ATMEL_ID_PIT	3	/* Periodic Interval Timer */
+#define ATMEL_ID_WDT	4	/* Watchdog timer */
+#define ATMEL_ID_PIOD	5	/* Parallel I/O Controller D */
+#define ATMEL_ID_USART0	6	/* USART 0 */
+#define ATMEL_ID_USART1	7	/* USART 1 */
+#define ATMEL_ID_DMA0	8	/* DMA Controller 0 */
+#define ATMEL_ID_ICM	9	/* Integrity Check Monitor */
+#define ATMEL_ID_PKCC	10	/* Public Key Crypto Controller */
+#define ATMEL_ID_AES	12	/* Advanced Encryption Standard */
+#define ATMEL_ID_AESB	13	/* AES Bridge*/
+#define ATMEL_ID_TDES	14	/* Triple Data Encryption Standard */
+#define ATMEL_ID_SHA    15	/* SHA Signature */
+#define ATMEL_ID_MPDDRC	16	/* MPDDR controller */
+#define ATMEL_ID_MATRIX1	17	/* H32MX, 32-bit AHB Matrix */
+#define ATMEL_ID_MATRIX0	18	/* H64MX, 64-bit AHB Matrix */
+#define ATMEL_ID_VDEC	19	/* Video Decoder */
+#define ATMEL_ID_SBM	20	/* Secure Box Module */
+#define ATMEL_ID_SMC	22	/* Multi-bit ECC interrupt */
+#define ATMEL_ID_PIOA	23	/* Parallel I/O Controller A */
+#define ATMEL_ID_PIOB	24	/* Parallel I/O Controller B */
+#define ATMEL_ID_PIOC	25	/* Parallel I/O Controller C */
+#define ATMEL_ID_PIOE	26	/* Parallel I/O Controller E */
+#define ATMEL_ID_UART0	27	/* UART 0 */
+#define ATMEL_ID_UART1	28	/* UART 1 */
+#define ATMEL_ID_USART2	29	/* USART 2 */
+#define ATMEL_ID_USART3	30	/* USART 3 */
+#define ATMEL_ID_USART4	31	/* USART 4 */
+#define ATMEL_ID_TWI0	32	/* Two-Wire Interface 0 */
+#define ATMEL_ID_TWI1	33	/* Two-Wire Interface 1 */
+#define ATMEL_ID_TWI2	34	/* Two-Wire Interface 2 */
+#define ATMEL_ID_MCI0	35	/* High Speed Multimedia Card Interface 0 */
+#define ATMEL_ID_MCI1	36	/* High Speed Multimedia Card Interface 1 */
+#define ATMEL_ID_SPI0	37	/* Serial Peripheral Interface 0 */
+#define ATMEL_ID_SPI1	38	/* Serial Peripheral Interface 1 */
+#define ATMEL_ID_SPI2	39	/* Serial Peripheral Interface 2 */
+#define ATMEL_ID_TC0	40	/* Timer Counter 0 (ch. 0, 1, 2) */
+#define ATMEL_ID_TC1	41	/* Timer Counter 1 (ch. 3, 4, 5) */
+#define ATMEL_ID_TC2	42	/* Timer Counter 2 (ch. 6, 7, 8) */
+#define ATMEL_ID_PWMC	43	/* Pulse Width Modulation Controller */
+#define ATMEL_ID_ADC	44	/* Touch Screen ADC Controller */
+#define ATMEL_ID_DBGU	45	/* Debug Unit Interrupt */
+#define ATMEL_ID_UHPHS	46	/* USB Host High Speed */
+#define ATMEL_ID_UDPHS	47	/* USB Device High Speed */
+#define ATMEL_ID_SSC0	48	/* Synchronous Serial Controller 0 */
+#define ATMEL_ID_SSC1	49	/* Synchronous Serial Controller 1 */
+#define ATMEL_ID_XDMAC1	50	/* DMA Controller 1 */
+#define ATMEL_ID_LCDC	51	/* LCD Controller */
+#define ATMEL_ID_ISI	52	/* Image Sensor Interface */
+#define ATMEL_ID_TRNG	53	/* True Random Number Generator */
+#define ATMEL_ID_GMAC0	54	/* Ethernet MAC 0 */
+#define ATMEL_ID_GMAC1	55	/* Ethernet MAC 1 */
+#define ATMEL_ID_IRQ	56	/* IRQ Interrupt ID */
+#define ATMEL_ID_SFC	57	/* Fuse Controller */
+#define ATMEL_ID_SECURAM	59	/* Secured RAM */
+#define ATMEL_ID_SMD	61	/* SMD Soft Modem */
+#define ATMEL_ID_TWI3	62	/* Two-Wire Interface 3 */
+#define ATMEL_ID_CATB	63	/* Capacitive Touch Controller */
+#define ATMEL_ID_SFR	64	/* Special Funcion Register */
+#define ATMEL_ID_AIC	65	/* Advanced Interrupt Controller */
+#define ATMEL_ID_SAIC	66	/* Secured Advanced Interrupt Controller */
+#define ATMEL_ID_L2CC	67	/* L2 Cache Controller */
+
+/*
+ * User Peripherals physical base addresses.
+ */
+#define ATMEL_BASE_LCDC		0xf0000000
+#define ATMEL_BASE_DMAC1	0xf0004000
+#define ATMEL_BASE_ISI		0xf0008000
+#define ATMEL_BASE_PKCC		0xf000C000
+#define ATMEL_BASE_MPDDRC	0xf0010000
+#define ATMEL_BASE_DMAC0	0xf0014000
+#define ATMEL_BASE_PMC		0xf0018000
+#define ATMEL_BASE_MATRIX0	0xf001c000
+#define ATMEL_BASE_AESB		0xf0020000
+/* Reserved: 0xf0024000 - 0xf8000000 */
+#define ATMEL_BASE_MCI0		0xf8000000
+#define ATMEL_BASE_UART0	0xf8004000
+#define ATMEL_BASE_SSC0		0xf8008000
+#define ATMEL_BASE_PWMC		0xf800c000
+#define ATMEL_BASE_SPI0		0xf8010000
+#define ATMEL_BASE_TWI0		0xf8014000
+#define ATMEL_BASE_TWI1		0xf8018000
+#define ATMEL_BASE_TC0		0xf801c000
+#define ATMEL_BASE_GMAC0	0xf8020000
+#define ATMEL_BASE_TWI2		0xf8024000
+#define ATMEL_BASE_SFR		0xf8028000
+#define ATMEL_BASE_USART0	0xf802c000
+#define ATMEL_BASE_USART1	0xf8030000
+/* Reserved:	0xf8034000 - 0xfc000000 */
+#define ATMEL_BASE_MCI1		0xfc000000
+#define ATMEL_BASE_UART1	0xfc004000
+#define ATMEL_BASE_USART2	0xfc008000
+#define ATMEL_BASE_USART3	0xfc00c000
+#define ATMEL_BASE_USART4	0xfc010000
+#define ATMEL_BASE_SSC1		0xfc014000
+#define ATMEL_BASE_SPI1		0xfc018000
+#define ATMEL_BASE_SPI2		0xfc01c000
+#define ATMEL_BASE_TC1		0xfc020000
+#define ATMEL_BASE_TC2		0xfc024000
+#define ATMEL_BASE_GMAC1	0xfc028000
+#define ATMEL_BASE_UDPHS	0xfc02c000
+#define ATMEL_BASE_TRNG		0xfc030000
+#define ATMEL_BASE_ADC		0xfc034000
+#define ATMEL_BASE_TWI3		0xfc038000
+
+#define ATMEL_BASE_SMC		0xfc05c000
+#define ATMEL_BASE_PMECC	(ATMEL_BASE_SMC + 0x070)
+#define ATMEL_BASE_PMERRLOC	(ATMEL_BASE_SMC + 0x500)
+
+#define ATMEL_BASE_PIOD		0xfc068000
+#define ATMEL_BASE_RSTC		0xfc068600
+#define ATMEL_BASE_PIT		0xfc068630
+#define ATMEL_BASE_WDT		0xfc068640
+
+#define ATMEL_BASE_DBGU		0xfc069000
+#define ATMEL_BASE_PIOA		0xfc06a000
+#define ATMEL_BASE_PIOB		0xfc06b000
+#define ATMEL_BASE_PIOC		0xfc06c000
+#define ATMEL_BASE_PIOE		0xfc06d000
+#define ATMEL_BASE_AIC		0xfc06e000
+
+/*
+ * Internal Memory.
+ */
+#define ATMEL_BASE_ROM		0x00000000	/* Internal ROM base address */
+#define ATMEL_BASE_NFC		0x00100000	/* NFC SRAM */
+#define ATMEL_BASE_SRAM		0x00200000	/* Internal ROM base address */
+#define ATMEL_BASE_VDEC		0x00300000	/* Video Decoder Controller */
+#define ATMEL_BASE_UDPHS_FIFO	0x00400000	/* USB Device HS controller */
+#define ATMEL_BASE_OHCI		0x00500000	/* USB Host controller (OHCI) */
+#define ATMEL_BASE_EHCI		0x00600000	/* USB Host controller (EHCI) */
+#define ATMEL_BASE_AXI		0x00700000
+#define ATMEL_BASE_DAP		0x00800000
+#define ATMEL_BASE_SMD		0x00900000
+
+/*
+ * External memory
+ */
+#define ATMEL_BASE_CS0		0x10000000
+#define ATMEL_BASE_DDRCS	0x20000000
+#define ATMEL_BASE_CS1		0x60000000
+#define ATMEL_BASE_CS2		0x70000000
+#define ATMEL_BASE_CS3		0x80000000
+
+/*
+ * Other misc defines
+ */
+#define ATMEL_PIO_PORTS		5
+#define CPU_HAS_PIO3
+#define PIO_SCDR_DIV		0x3fff
+#define CPU_HAS_PCR
+#define CPU_HAS_H32MXDIV
+
+/*
+ * The clock of peripheral connect to H32MX is decided by H32MXDIV
+ * bit in MCKR, if this bit is set, the peripheral only work at half
+ * of MCK, the MCKR address is 0xf0018030, and H32MXDIV is bit 24.
+ */
+#define H32MXDIV	(readl(0xF0018030) & (1 << 24) ? 2 : 1)
+
+/*
+ * No PMECC Galois table in ROM
+ */
+#define NO_GALOIS_TABLE_IN_ROM
+
+#ifndef __ASSEMBLY__
+unsigned int get_chip_id(void);
+unsigned int get_extension_chip_id(void);
+unsigned int has_emac(void);
+unsigned int has_gmac(void);
+unsigned int has_lcdc(void);
+char *get_cpu_name(void);
+#endif
+
+#endif
diff --git a/board/atmel/sama5d4ek/Kconfig b/board/atmel/sama5d4ek/Kconfig
new file mode 100644
index 0000000..a889895
--- /dev/null
+++ b/board/atmel/sama5d4ek/Kconfig
@@ -0,0 +1,18 @@ 
+if TARGET_SAMA5D4EK
+
+config SYS_CPU
+	default "armv7"
+
+config SYS_BOARD
+	default "sama5d4ek"
+
+config SYS_VENDOR
+	default "atmel"
+
+config SYS_SOC
+	default "at91"
+
+config SYS_CONFIG_NAME
+	default "sama5d4ek"
+
+endif
diff --git a/board/atmel/sama5d4ek/MAINTAINERS b/board/atmel/sama5d4ek/MAINTAINERS
new file mode 100644
index 0000000..afe88dd
--- /dev/null
+++ b/board/atmel/sama5d4ek/MAINTAINERS
@@ -0,0 +1,8 @@ 
+SAMA5D4EK BOARD
+M:	Bo Shen <voice.shen@atmel.com>
+S:	Maintained
+F:	board/atmel/sama5d4ek/
+F:	include/configs/sama5d4ek.h
+F:	configs/sama5d4ek_mmc_defconfig
+F:	configs/sama5d4ek_nandflash_defconfig
+F:	configs/sama5d4ek_spiflash_defconfig
diff --git a/board/atmel/sama5d4ek/Makefile b/board/atmel/sama5d4ek/Makefile
new file mode 100644
index 0000000..d91525c
--- /dev/null
+++ b/board/atmel/sama5d4ek/Makefile
@@ -0,0 +1,15 @@ 
+#
+# (C) Copyright 2003-2008
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2008
+# Stelian Pop <stelian@popies.net>
+# Lead Tech Design <www.leadtechdesign.com>
+#
+# (C) Copyright 2014
+# Bo Shen <voice.shen@atmel.com>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += sama5d4ek.o
diff --git a/board/atmel/sama5d4ek/sama5d4ek.c b/board/atmel/sama5d4ek/sama5d4ek.c
new file mode 100644
index 0000000..099b924
--- /dev/null
+++ b/board/atmel/sama5d4ek/sama5d4ek.c
@@ -0,0 +1,322 @@ 
+/*
+ * Copyright (C) 2014 Atmel
+ *		      Bo Shen <voice.shen@atmel.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/sama5d3_smc.h>
+#include <asm/arch/sama5d4.h>
+#include <atmel_lcdc.h>
+#include <atmel_mci.h>
+#include <lcd.h>
+#include <mmc.h>
+#include <net.h>
+#include <netdev.h>
+#include <nand.h>
+#include <spi.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_ATMEL_SPI
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+	return bus == 0 && cs == 0;
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+	at91_set_pio_output(AT91_PIO_PORTC, 3, 0);
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+	at91_set_pio_output(AT91_PIO_PORTC, 3, 1);
+}
+
+static void sama5d4ek_spi0_hw_init(void)
+{
+	at91_set_a_periph(AT91_PIO_PORTC, 0, 0);	/* SPI0_MISO */
+	at91_set_a_periph(AT91_PIO_PORTC, 1, 0);	/* SPI0_MOSI */
+	at91_set_a_periph(AT91_PIO_PORTC, 2, 0);	/* SPI0_SPCK */
+
+	at91_set_pio_output(AT91_PIO_PORTC, 3, 1);	/* SPI0_CS0 */
+
+	/* Enable clock */
+	at91_periph_clk_enable(ATMEL_ID_SPI0);
+}
+#endif /* CONFIG_ATMEL_SPI */
+
+#ifdef CONFIG_NAND_ATMEL
+static void sama5d4ek_nand_hw_init(void)
+{
+	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+
+	at91_periph_clk_enable(ATMEL_ID_SMC);
+
+	/* Configure SMC CS3 for NAND */
+	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) |
+	       AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(1),
+	       &smc->cs[3].setup);
+	writel(AT91_SMC_PULSE_NWE(2) | AT91_SMC_PULSE_NCS_WR(3) |
+	       AT91_SMC_PULSE_NRD(2) | AT91_SMC_PULSE_NCS_RD(3),
+	       &smc->cs[3].pulse);
+	writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
+	       &smc->cs[3].cycle);
+	writel(AT91_SMC_TIMINGS_TCLR(2) | AT91_SMC_TIMINGS_TADL(7) |
+	       AT91_SMC_TIMINGS_TAR(2)  | AT91_SMC_TIMINGS_TRR(3)   |
+	       AT91_SMC_TIMINGS_TWB(7)  | AT91_SMC_TIMINGS_RBNSEL(3)|
+	       AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings);
+	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+	       AT91_SMC_MODE_EXNW_DISABLE |
+	       AT91_SMC_MODE_DBW_8 |
+	       AT91_SMC_MODE_TDF_CYCLE(3),
+	       &smc->cs[3].mode);
+
+	at91_set_a_periph(AT91_PIO_PORTC, 5, 0);	/* D0 */
+	at91_set_a_periph(AT91_PIO_PORTC, 6, 0);	/* D1 */
+	at91_set_a_periph(AT91_PIO_PORTC, 7, 0);	/* D2 */
+	at91_set_a_periph(AT91_PIO_PORTC, 8, 0);	/* D3 */
+	at91_set_a_periph(AT91_PIO_PORTC, 9, 0);	/* D4 */
+	at91_set_a_periph(AT91_PIO_PORTC, 10, 0);	/* D5 */
+	at91_set_a_periph(AT91_PIO_PORTC, 11, 0);	/* D6 */
+	at91_set_a_periph(AT91_PIO_PORTC, 12, 0);	/* D7 */
+	at91_set_a_periph(AT91_PIO_PORTC, 13, 0);	/* RE */
+	at91_set_a_periph(AT91_PIO_PORTC, 14, 0);	/* WE */
+	at91_set_a_periph(AT91_PIO_PORTC, 15, 1);	/* NCS */
+	at91_set_a_periph(AT91_PIO_PORTC, 16, 1);	/* RDY */
+	at91_set_a_periph(AT91_PIO_PORTC, 17, 1);	/* ALE */
+	at91_set_a_periph(AT91_PIO_PORTC, 18, 1);	/* CLE */
+}
+#endif
+
+#ifdef CONFIG_CMD_USB
+static void sama5d4ek_usb_hw_init(void)
+{
+	at91_set_pio_output(AT91_PIO_PORTE, 11, 0);
+	at91_set_pio_output(AT91_PIO_PORTE, 12, 0);
+	at91_set_pio_output(AT91_PIO_PORTE, 10, 0);
+}
+#endif
+
+#ifdef CONFIG_LCD
+vidinfo_t panel_info = {
+	.vl_col = 800,
+	.vl_row = 480,
+	.vl_clk = 33260000,
+	.vl_sync = ATMEL_LCDC_INVLINE_NORMAL | ATMEL_LCDC_INVFRAME_NORMAL,
+	.vl_bpix = LCD_BPP,
+	.vl_tft = 1,
+	.vl_hsync_len = 5,
+	.vl_left_margin = 128,
+	.vl_right_margin = 0,
+	.vl_vsync_len = 5,
+	.vl_upper_margin = 23,
+	.vl_lower_margin = 22,
+	.mmio = ATMEL_BASE_LCDC,
+};
+
+/* No power up/down pin for the LCD pannel */
+void lcd_enable(void)	{ /* Empty! */ }
+void lcd_disable(void)	{ /* Empty! */ }
+
+unsigned int has_lcdc(void)
+{
+	return 1;
+}
+
+static void sama5d4ek_lcd_hw_init(void)
+{
+	at91_set_a_periph(AT91_PIO_PORTA, 24, 0);	/* LCDPWM */
+	at91_set_a_periph(AT91_PIO_PORTA, 25, 0);	/* LCDDISP */
+	at91_set_a_periph(AT91_PIO_PORTA, 26, 0);	/* LCDVSYNC */
+	at91_set_a_periph(AT91_PIO_PORTA, 27, 0);	/* LCDHSYNC */
+	at91_set_a_periph(AT91_PIO_PORTA, 28, 0);	/* LCDDOTCK */
+	at91_set_a_periph(AT91_PIO_PORTA, 29, 0);	/* LCDDEN */
+
+	at91_set_a_periph(AT91_PIO_PORTA,  2, 0);	/* LCDD2 */
+	at91_set_a_periph(AT91_PIO_PORTA,  3, 0);	/* LCDD3 */
+	at91_set_a_periph(AT91_PIO_PORTA,  4, 0);	/* LCDD4 */
+	at91_set_a_periph(AT91_PIO_PORTA,  5, 0);	/* LCDD5 */
+	at91_set_a_periph(AT91_PIO_PORTA,  6, 0);	/* LCDD6 */
+	at91_set_a_periph(AT91_PIO_PORTA,  7, 0);	/* LCDD7 */
+
+	at91_set_a_periph(AT91_PIO_PORTA, 10, 0);	/* LCDD10 */
+	at91_set_a_periph(AT91_PIO_PORTA, 11, 0);	/* LCDD11 */
+	at91_set_a_periph(AT91_PIO_PORTA, 12, 0);	/* LCDD12 */
+	at91_set_a_periph(AT91_PIO_PORTA, 13, 0);	/* LCDD13 */
+	at91_set_a_periph(AT91_PIO_PORTA, 14, 0);	/* LCDD14 */
+	at91_set_a_periph(AT91_PIO_PORTA, 15, 0);	/* LCDD15 */
+
+	at91_set_a_periph(AT91_PIO_PORTA, 18, 0);	/* LCDD18 */
+	at91_set_a_periph(AT91_PIO_PORTA, 19, 0);	/* LCDD19 */
+	at91_set_a_periph(AT91_PIO_PORTA, 20, 0);	/* LCDD20 */
+	at91_set_a_periph(AT91_PIO_PORTA, 21, 0);	/* LCDD21 */
+	at91_set_a_periph(AT91_PIO_PORTA, 22, 0);	/* LCDD22 */
+	at91_set_a_periph(AT91_PIO_PORTA, 23, 0);	/* LCDD23 */
+
+	/* Enable clock */
+	at91_periph_clk_enable(ATMEL_ID_LCDC);
+}
+
+#ifdef CONFIG_LCD_INFO
+void lcd_show_board_info(void)
+{
+	ulong dram_size, nand_size;
+	int i;
+	char temp[32];
+
+	lcd_printf("2014 ATMEL Corp\n");
+	lcd_printf("at91@atmel.com\n");
+	lcd_printf("%s CPU at %s MHz\n", get_cpu_name(),
+		   strmhz(temp, get_cpu_clk_rate()));
+
+	dram_size = 0;
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
+		dram_size += gd->bd->bi_dram[i].size;
+
+	nand_size = 0;
+#ifdef CONFIG_NAND_ATMEL
+	for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
+		nand_size += nand_info[i].size;
+#endif
+	lcd_printf("%ld MB SDRAM, %ld MB NAND\n",
+		   dram_size >> 20, nand_size >> 20);
+}
+#endif /* CONFIG_LCD_INFO */
+
+#endif /* CONFIG_LCD */
+
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+void sama5d4ek_mci1_hw_init(void)
+{
+	at91_set_c_periph(AT91_PIO_PORTE, 19, 1);	/* MCI1 CDA */
+	at91_set_c_periph(AT91_PIO_PORTE, 20, 1);	/* MCI1 DA0 */
+	at91_set_c_periph(AT91_PIO_PORTE, 21, 1);	/* MCI1 DA1 */
+	at91_set_c_periph(AT91_PIO_PORTE, 22, 1);	/* MCI1 DA2 */
+	at91_set_c_periph(AT91_PIO_PORTE, 23, 1);	/* MCI1 DA3 */
+	at91_set_c_periph(AT91_PIO_PORTE, 18, 0);	/* MCI1 CLK */
+
+	/*
+	 * As the mci io internal pull down is too strong, so if the io needs
+	 * external pull up, the pull up resistor will be very small, if so
+	 * the power consumption will increase, so disable the interanl pull
+	 * down to save the power.
+	 */
+	at91_set_pio_pulldown(AT91_PIO_PORTE, 18, 0);
+	at91_set_pio_pulldown(AT91_PIO_PORTE, 19, 0);
+	at91_set_pio_pulldown(AT91_PIO_PORTE, 20, 0);
+	at91_set_pio_pulldown(AT91_PIO_PORTE, 21, 0);
+	at91_set_pio_pulldown(AT91_PIO_PORTE, 22, 0);
+	at91_set_pio_pulldown(AT91_PIO_PORTE, 23, 0);
+
+	/* Enable clock */
+	at91_periph_clk_enable(ATMEL_ID_MCI1);
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	/* Enable power for MCI1 interface */
+	at91_set_pio_output(AT91_PIO_PORTE, 15, 0);
+
+	return atmel_mci_init((void *)ATMEL_BASE_MCI1);
+}
+#endif /* CONFIG_GENERIC_ATMEL_MCI */
+
+#ifdef CONFIG_MACB
+void sama5d4ek_macb0_hw_init(void)
+{
+	at91_set_a_periph(AT91_PIO_PORTB, 0, 0);	/* ETXCK_EREFCK */
+	at91_set_a_periph(AT91_PIO_PORTB, 6, 0);	/* ERXDV */
+	at91_set_a_periph(AT91_PIO_PORTB, 8, 0);	/* ERX0 */
+	at91_set_a_periph(AT91_PIO_PORTB, 9, 0);	/* ERX1 */
+	at91_set_a_periph(AT91_PIO_PORTB, 7, 0);	/* ERXER */
+	at91_set_a_periph(AT91_PIO_PORTB, 2, 0);	/* ETXEN */
+	at91_set_a_periph(AT91_PIO_PORTB, 12, 0);	/* ETX0 */
+	at91_set_a_periph(AT91_PIO_PORTB, 13, 0);	/* ETX1 */
+	at91_set_a_periph(AT91_PIO_PORTB, 17, 0);	/* EMDIO */
+	at91_set_a_periph(AT91_PIO_PORTB, 16, 0);	/* EMDC */
+
+	/* Enable clock */
+	at91_periph_clk_enable(ATMEL_ID_GMAC0);
+}
+#endif
+
+char *get_cpu_name()
+{
+	return "SAMA5D4";
+}
+
+static void sama5d4ek_serial3_hw_init(void)
+{
+	at91_set_b_periph(AT91_PIO_PORTE, 17, 1);	/* TXD3 */
+	at91_set_b_periph(AT91_PIO_PORTE, 16, 0);	/* RXD3 */
+
+	/* Enable clock */
+	at91_periph_clk_enable(ATMEL_ID_USART3);
+}
+
+int board_early_init_f(void)
+{
+	at91_periph_clk_enable(ATMEL_ID_PIOA);
+	at91_periph_clk_enable(ATMEL_ID_PIOB);
+	at91_periph_clk_enable(ATMEL_ID_PIOC);
+	at91_periph_clk_enable(ATMEL_ID_PIOD);
+	at91_periph_clk_enable(ATMEL_ID_PIOE);
+
+	sama5d4ek_serial3_hw_init();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+#ifdef CONFIG_ATMEL_SPI
+	sama5d4ek_spi0_hw_init();
+#endif
+#ifdef CONFIG_NAND_ATMEL
+	sama5d4ek_nand_hw_init();
+#endif
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+	sama5d4ek_mci1_hw_init();
+#endif
+#ifdef CONFIG_MACB
+	sama5d4ek_macb0_hw_init();
+#endif
+#ifdef CONFIG_LCD
+	sama5d4ek_lcd_hw_init();
+#endif
+#ifdef CONFIG_CMD_USB
+	sama5d4ek_usb_hw_init();
+#endif
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+				    CONFIG_SYS_SDRAM_SIZE);
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+
+#ifdef CONFIG_MACB
+	rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00);
+#endif
+
+	return rc;
+}
diff --git a/configs/sama5d4ek_mmc_defconfig b/configs/sama5d4ek_mmc_defconfig
new file mode 100644
index 0000000..16a5ed7
--- /dev/null
+++ b/configs/sama5d4ek_mmc_defconfig
@@ -0,0 +1,3 @@ 
+CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_MMC"
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_SAMA5D4EK=y
diff --git a/configs/sama5d4ek_nandflash_defconfig b/configs/sama5d4ek_nandflash_defconfig
new file mode 100644
index 0000000..8b7fbc3
--- /dev/null
+++ b/configs/sama5d4ek_nandflash_defconfig
@@ -0,0 +1,3 @@ 
+CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_NANDFLASH"
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_SAMA5D4EK=y
diff --git a/configs/sama5d4ek_spiflash_defconfig b/configs/sama5d4ek_spiflash_defconfig
new file mode 100644
index 0000000..63e9b6c
--- /dev/null
+++ b/configs/sama5d4ek_spiflash_defconfig
@@ -0,0 +1,3 @@ 
+CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_SERIALFLASH"
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_SAMA5D4EK=y
diff --git a/include/configs/sama5d4ek.h b/include/configs/sama5d4ek.h
new file mode 100644
index 0000000..d50897e
--- /dev/null
+++ b/include/configs/sama5d4ek.h
@@ -0,0 +1,215 @@ 
+/*
+ * Configuration settings for the SAMA5D4EK board.
+ *
+ * Copyright (C) 2014 Atmel
+ *		      Bo Shen <voice.shen@atmel.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/hardware.h>
+
+#define CONFIG_SYS_TEXT_BASE		0x26f00000
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_SLOW_CLOCK      32768
+#define CONFIG_SYS_AT91_MAIN_CLOCK      12000000 /* from 12 MHz crystal */
+#define CONFIG_SYS_HZ		        1000
+
+#define CONFIG_ARCH_CPU_INIT
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_DISPLAY_CPUINFO
+
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_OF_LIBFDT		/* Device Tree support */
+
+#define CONFIG_SYS_GENERIC_BOARD
+
+/* general purpose I/O */
+#define CONFIG_AT91_GPIO
+
+/* serial console */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE		ATMEL_BASE_USART3
+#define	CONFIG_USART_ID			ATMEL_ID_USART3
+
+#define CONFIG_BOOTDELAY		3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/* No NOR flash */
+#define CONFIG_SYS_NO_FLASH
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_LOADS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_SETEXPR
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
+#define CONFIG_SYS_SDRAM_SIZE		0x20000000
+
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+
+#define CONFIG_SYS_LOAD_ADDR		0x22000000 /* load address */
+
+/* SerialFlash */
+#define CONFIG_CMD_SF
+
+#ifdef CONFIG_CMD_SF
+#define CONFIG_ATMEL_SPI
+#define CONFIG_ATMEL_SPI0
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ATMEL
+#define CONFIG_SF_DEFAULT_BUS		0
+#define CONFIG_SF_DEFAULT_CS		0
+#define CONFIG_SF_DEFAULT_SPEED		30000000
+#endif
+
+/* NAND flash */
+#define CONFIG_CMD_NAND
+
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		ATMEL_BASE_CS3
+/* our ALE is AD21 */
+#define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
+/* our CLE is AD22 */
+#define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+/* PMECC & PMERRLOC */
+#define CONFIG_ATMEL_NAND_HWECC
+#define CONFIG_ATMEL_NAND_HW_PMECC
+#endif
+
+/* MMC */
+#define CONFIG_CMD_MMC
+
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_GENERIC_ATMEL_MCI
+#define ATMEL_BASE_MMCI			ATMEL_BASE_MCI1
+#endif
+
+/* USB */
+#define CONFIG_CMD_USB
+
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_ATMEL
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	3
+#define CONFIG_USB_STORAGE
+#endif
+
+#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Ethernet Hardware */
+#define CONFIG_MACB
+#define CONFIG_RMII
+#define CONFIG_NET_RETRY_COUNT		20
+#define CONFIG_MACB_SEARCH_PHY
+
+/* LCD */
+#define CONFIG_LCD
+#define LCD_BPP				LCD_COLOR16
+#define LCD_OUTPUT_BPP                  18
+#define CONFIG_LCD_LOGO
+#define CONFIG_LCD_INFO
+#define CONFIG_LCD_INFO_BELOW_LOGO
+#define CONFIG_SYS_WHITE_ON_BLACK
+#define CONFIG_ATMEL_HLCD
+#define CONFIG_ATMEL_LCD_RGB565
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+#ifdef CONFIG_SYS_USE_SERIALFLASH
+/* bootstrap + u-boot + env + linux in serial flash */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS	CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS	CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_OFFSET       0x10000
+#define CONFIG_ENV_SIZE         0x10000
+#define CONFIG_ENV_SECT_SIZE    0x1000
+#define CONFIG_BOOTCOMMAND      "sf probe 0; " \
+				"sf read 0x21000000 0xa0000 0x60000; " \
+				"sf read 0x22000000 0x100000 0x300000; " \
+				"bootz 0x22000000 - 0x21000000"
+#elif CONFIG_SYS_USE_NANDFLASH
+/* bootstrap + u-boot + env in nandflash */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET		0xc0000
+#define CONFIG_ENV_OFFSET_REDUND	0x100000
+#define CONFIG_ENV_SIZE			0x20000
+#define CONFIG_BOOTCOMMAND	"nand read 0x21000000 0x180000 0x80000;" \
+				"nand read 0x22000000 0x200000 0x600000;" \
+				"bootz 0x22000000 - 0x21000000"
+#elif CONFIG_SYS_USE_MMC
+/* bootstrap + u-boot + env in sd card */
+#define CONFIG_ENV_IS_IN_FAT
+#define CONFIG_FAT_WRITE
+#define FAT_ENV_INTERFACE	"mmc"
+/*
+ * We don't specify the part number, if device 0 has partition table, it means
+ * the first partition; it no partition table, then take whole device as a
+ * FAT file system.
+ */
+#define FAT_ENV_DEVICE_AND_PART	"0"
+#define FAT_ENV_FILE		"uboot.env"
+#define CONFIG_ENV_SIZE		0x4000
+#define CONFIG_BOOTCOMMAND	"fatload mmc 0:1 0x21000000 sama5d4ek.dtb; " \
+				"fatload mmc 0:1 0x22000000 zImage; " \
+				"bootz 0x22000000 - 0x21000000"
+#endif
+
+#ifdef CONFIG_SYS_USE_MMC
+#define CONFIG_BOOTARGS							\
+	"console=ttyS0,115200 earlyprintk "				\
+	"root=/dev/mmcblk0p2 rw rootwait"
+#else
+#define CONFIG_BOOTARGS							\
+	"console=ttyS0,115200 earlyprintk "				\
+	"mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,"		\
+	"256K(env),256k(evn_redundent),256k(spare),"			\
+	"512k(dtb),6M(kernel)ro,-(rootfs) "				\
+	"rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs"
+#endif
+
+#define CONFIG_BAUDRATE			115200
+
+#define CONFIG_SYS_PROMPT		"U-Boot> "
+#define CONFIG_SYS_CBSIZE		256
+#define CONFIG_SYS_MAXARGS		16
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
+
+#endif