@@ -27,3 +27,33 @@ Example (MPC8610HPCD):
compatible = "fsl,fpga-pixis";
reg = <0xe8000000 32>;
};
+
+* Freescale BCSR GPIO banks
+
+Some BCSR registers act as simple GPIO controllers, each such
+register can be represented by the gpio-controller node.
+
+Required properities:
+- compatible : Should be "fsl,<board>-bcsr-gpio";
+- reg : Should contain the address and the lenght of the GPIO bank
+ register;
+- #gpio-cells : Should be two. The first cell is the pin number and the
+ second cell is used to specify optional paramters (currently unused);
+- gpio-controller : Marks the port as GPIO controller.
+
+Example:
+
+ bcsr@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "board-control";
+ reg = <1 0 0x8000>;
+ ranges = <0 1 0 0x8000>;
+
+ bcsr13: gpio-controller@d {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8360mds-bcsr-gpio";
+ reg = <0xd 1>;
+ gpio-controller;
+ };
+ };
@@ -303,4 +303,15 @@ config OF_RTC
source "arch/powerpc/sysdev/bestcomm/Kconfig"
+config SIMPLE_GPIO
+ bool "Support for simple, memory-mapped GPIO controllers"
+ depends on PPC
+ select GENERIC_GPIO
+ select ARCH_REQUIRE_GPIOLIB
+ help
+ Say Y here to support simple, memory-mapped GPIO controllers.
+ These are usually BCSRs used to control board's switches, LEDs,
+ chip-selects, Ethernet/USB PHY's power and various other small
+ on-board peripherals.
+
endmenu
@@ -32,6 +32,7 @@ obj-$(CONFIG_4xx) += uic.o
obj-$(CONFIG_4xx_SOC) += ppc4xx_soc.o
obj-$(CONFIG_XILINX_VIRTEX) += xilinx_intc.o
obj-$(CONFIG_OF_RTC) += of_rtc.o
+obj-$(CONFIG_SIMPLE_GPIO) += simple_gpio.o
ifeq ($(CONFIG_PCI),y)
obj-$(CONFIG_4xx) += ppc4xx_pci.o
endif
new file mode 100644
@@ -0,0 +1,157 @@
+/*
+ * Simple Memory-Mapped GPIOs
+ *
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ *
+ * Author: Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/gpio.h>
+#include <asm/prom.h>
+#include "simple_gpio.h"
+
+struct u8_gpio_chip {
+ struct of_mm_gpio_chip mm_gc;
+ spinlock_t lock;
+
+ /* shadowed data register to clear/set bits safely */
+ u8 data;
+};
+
+static struct u8_gpio_chip *to_u8_gpio_chip(struct of_mm_gpio_chip *mm_gc)
+{
+ return container_of(mm_gc, struct u8_gpio_chip, mm_gc);
+}
+
+static u8 u8_pin2mask(unsigned int pin)
+{
+ return 1 << (8 - 1 - pin);
+}
+
+static int u8_gpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+
+ return in_8(mm_gc->regs) & u8_pin2mask(gpio);
+}
+
+static void u8_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct u8_gpio_chip *u8_gc = to_u8_gpio_chip(mm_gc);
+ unsigned long flags;
+
+ spin_lock_irqsave(&u8_gc->lock, flags);
+
+ if (val)
+ u8_gc->data |= u8_pin2mask(gpio);
+ else
+ u8_gc->data &= ~u8_pin2mask(gpio);
+
+ out_8(mm_gc->regs, u8_gc->data);
+
+ spin_unlock_irqrestore(&u8_gc->lock, flags);
+}
+
+static int u8_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+ return 0;
+}
+
+static int u8_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ u8_gpio_set(gc, gpio, val);
+ return 0;
+}
+
+static void u8_gpio_save_regs(struct of_mm_gpio_chip *mm_gc)
+{
+ struct u8_gpio_chip *u8_gc = to_u8_gpio_chip(mm_gc);
+
+ u8_gc->data = in_8(mm_gc->regs);
+}
+
+static int __init u8_simple_gpiochip_add(struct device_node *np)
+{
+ int ret;
+ struct u8_gpio_chip *u8_gc;
+ struct of_mm_gpio_chip *mm_gc;
+ struct of_gpio_chip *of_gc;
+ struct gpio_chip *gc;
+
+ u8_gc = kzalloc(sizeof(*u8_gc), GFP_KERNEL);
+ if (!u8_gc)
+ return -ENOMEM;
+
+ spin_lock_init(&u8_gc->lock);
+
+ mm_gc = &u8_gc->mm_gc;
+ of_gc = &mm_gc->of_gc;
+ gc = &of_gc->gc;
+
+ mm_gc->save_regs = u8_gpio_save_regs;
+ of_gc->gpio_cells = 2;
+ gc->ngpio = 8;
+ gc->direction_input = u8_gpio_dir_in;
+ gc->direction_output = u8_gpio_dir_out;
+ gc->get = u8_gpio_get;
+ gc->set = u8_gpio_set;
+
+ ret = of_mm_gpiochip_add(np, mm_gc);
+ if (ret)
+ goto err;
+ return 0;
+err:
+ kfree(u8_gc);
+ return ret;
+}
+
+int __init simple_gpiochip_init(const char *compatible)
+{
+ struct device_node *np;
+
+ for_each_compatible_node(np, NULL, compatible) {
+ int ret;
+ struct resource r;
+
+ ret = of_address_to_resource(np, 0, &r);
+ if (ret)
+ goto err;
+
+ switch (resource_size(&r)) {
+ case 1:
+ ret = u8_simple_gpiochip_add(np);
+ if (ret)
+ goto err;
+ break;
+ default:
+ /*
+ * Whenever you need support for GPIO bank width > 1,
+ * please just turn u8_ code into huge macros, and
+ * construct needed uX_ code with it.
+ */
+ ret = -ENOSYS;
+ goto err;
+ }
+ continue;
+err:
+ pr_err("%s: registration failed, status %d\n",
+ np->full_name, ret);
+ }
+ return 0;
+}
+EXPORT_SYMBOL(simple_gpiochip_init);
new file mode 100644
@@ -0,0 +1,13 @@
+#ifndef __SYSDEV_SIMPLE_GPIO_H
+#define __SYSDEV_SIMPLE_GPIO_H
+
+#ifdef CONFIG_SIMPLE_GPIO
+extern int __init simple_gpiochip_init(const char *compatible);
+#else
+static inline int __init simple_gpiochip_init(const char *compatible)
+{
+ return -ENODEV;
+}
+#endif /* CONFIG_SIMPLE_GPIO */
+
+#endif /* __SYSDEV_SIMPLE_GPIO_H */
The driver supports very simple GPIO controllers, that is, when a controller provides just a 'data' register. Such controllers may be found in various BCSRs (Board's FPGAs used to control board's switches, LEDs, chip-selects, Ethernet/USB PHY power, etc). So far we support only 1-byte GPIO banks. Support for other widths may be implemented when/if needed. p.s. To avoid "made up" compatible entries (like compatible = "simple-gpio"), boards must call the simple_gpiochip_init() to pass the compatible string. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> --- Documentation/powerpc/dts-bindings/fsl/board.txt | 30 ++++ arch/powerpc/platforms/Kconfig | 11 ++ arch/powerpc/sysdev/Makefile | 1 + arch/powerpc/sysdev/simple_gpio.c | 157 ++++++++++++++++++++++ arch/powerpc/sysdev/simple_gpio.h | 13 ++ 5 files changed, 212 insertions(+), 0 deletions(-) create mode 100644 arch/powerpc/sysdev/simple_gpio.c create mode 100644 arch/powerpc/sysdev/simple_gpio.h