new file mode 100644
@@ -0,0 +1,51 @@
+Atmel Image Sensor Interface (ISI) SoC Camera Subsystem
+----------------------------------------------
+
+Required properties:
+- compatible: must be "atmel,at91sam9g45-isi"
+- reg: physical base address and length of the registers set for the device;
+- interrupts: should contain IRQ line for the ISI;
+- clocks: list of clock specifiers, corresponding to entries in
+ the clock-names property;
+- clock-names: must contain "isi_clk", which is the isi peripherial clock.
+
+ISI supports a single port node with parallel bus. It should contain one
+'port' child node with child 'endpoint' node. Please refer to the bindings
+defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+ isi: isi@f0034000 {
+ compatible = "atmel,at91sam9g45-isi";
+ reg = <0xf0034000 0x4000>;
+ interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>;
+
+ clocks = <&isi_clk>;
+ clock-names = "isi_clk";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_isi>;
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ isi_0: endpoint {
+ remote-endpoint = <&ov2640_0>;
+ bus-width = <8>;
+ };
+ };
+ };
+
+ i2c1: i2c@f0018000 {
+ ov2640: camera@0x30 {
+ compatible = "omnivision,ov2640";
+ reg = <0x30>;
+
+ port {
+ ov2640_0: endpoint {
+ remote-endpoint = <&isi_0>;
+ bus-width = <8>;
+ };
+ };
+ };
+ };
@@ -25,6 +25,7 @@
#include <media/atmel-isi.h>
#include <media/soc_camera.h>
#include <media/soc_mediabus.h>
+#include <media/v4l2-of.h>
#include <media/videobuf2-dma-contig.h>
#define MAX_BUFFER_NUM 32
@@ -33,6 +34,7 @@
#define VID_LIMIT_BYTES (16 * 1024 * 1024)
#define MIN_FRAME_RATE 15
#define FRAME_INTERVAL_MILLI_SEC (1000 / MIN_FRAME_RATE)
+#define ISI_DEFAULT_MCLK_FREQ 25000000
/* Frame buffer descriptor */
struct fbd {
@@ -883,6 +885,51 @@ static int atmel_isi_remove(struct platform_device *pdev)
return 0;
}
+static int atmel_isi_probe_dt(struct atmel_isi *isi,
+ struct platform_device *pdev)
+{
+ struct device_node *np= pdev->dev.of_node;
+ struct v4l2_of_endpoint ep;
+ int err;
+
+ /* Default settings for ISI */
+ isi->pdata.full_mode = 1;
+ isi->pdata.mck_hz = ISI_DEFAULT_MCLK_FREQ;
+ isi->pdata.frate = ISI_CFG1_FRATE_CAPTURE_ALL;
+
+ np = of_graph_get_next_endpoint(np, NULL);
+ if (!np) {
+ dev_err(&pdev->dev, "Could not find the endpoint\n");
+ return -EINVAL;
+ }
+
+ err = v4l2_of_parse_endpoint(np, &ep);
+ if (err) {
+ dev_err(&pdev->dev, "Could not parse the endpoint\n");
+ goto err_probe_dt;
+ }
+
+ switch (ep.bus.parallel.bus_width) {
+ case 8:
+ isi->pdata.data_width_flags = ISI_DATAWIDTH_8;
+ break;
+ case 10:
+ isi->pdata.data_width_flags =
+ ISI_DATAWIDTH_8 | ISI_DATAWIDTH_10;
+ break;
+ default:
+ dev_err(&pdev->dev, "Unsupported bus width: %d\n",
+ ep.bus.parallel.bus_width);
+ err = -EINVAL;
+ goto err_probe_dt;
+ }
+
+err_probe_dt:
+ of_node_put(np);
+
+ return err;
+}
+
static int atmel_isi_probe(struct platform_device *pdev)
{
unsigned int irq;
@@ -894,7 +941,7 @@ static int atmel_isi_probe(struct platform_device *pdev)
struct isi_platform_data *pdata;
pdata = dev->platform_data;
- if (!pdata || !pdata->data_width_flags) {
+ if ((!pdata || !pdata->data_width_flags) && !pdev->dev.of_node) {
dev_err(&pdev->dev,
"No config available for Atmel ISI\n");
return -EINVAL;
@@ -910,7 +957,14 @@ static int atmel_isi_probe(struct platform_device *pdev)
if (IS_ERR(isi->pclk))
return PTR_ERR(isi->pclk);
- memcpy(&isi->pdata, pdata, sizeof(isi->pdata));
+ if (pdata) {
+ memcpy(&isi->pdata, pdata, sizeof(isi->pdata));
+ } else {
+ ret = atmel_isi_probe_dt(isi, pdev);
+ if (ret)
+ return ret;
+ }
+
isi->active = NULL;
spin_lock_init(&isi->lock);
INIT_LIST_HEAD(&isi->video_buffer_list);
@@ -1012,11 +1066,18 @@ err_alloc_ctx:
return ret;
}
+static const struct of_device_id atmel_isi_of_match[] = {
+ { .compatible = "atmel,at91sam9g45-isi" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, atmel_isi_of_match);
+
static struct platform_driver atmel_isi_driver = {
.remove = atmel_isi_remove,
.driver = {
.name = "atmel_isi",
.owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(atmel_isi_of_match),
},
};