deleted file mode 100644
@@ -1,9 +0,0 @@
-#
-# Copyright 2010-2011 Freescale Semiconductor, Inc.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += p1023rds.o
-obj-y += law.o
-obj-y += tlb.o
deleted file mode 100644
@@ -1,101 +0,0 @@
-Overview
---------
-The P1023 process includes a performance optimized implementation of the
-QorIQ data Path Acceleration Architecture (DPAA). This architecture
-provides the infrastructure to support simplified sharing of networking
-interfaces and accelerators by multiple CPU cores. P1023 is an e500 based
-dual core SOC.
-
-P1023RDS board is a Low End Dual core platform supporting the P1023
-processor of QorIQ series.
-
-Building U-boot
----------------
-To build the u-boot for P1023RDS:
-Configure to NOR boot:
- make P1023RDS_config
-Configure to NAND boot:
- make P1023RDS_NAND_config
-Build:
- make
-
-Board Switches
---------------
-Most switches on the board should not be changed. The most frequent
-user-settable switches on the board are used to configure
-the flash banks.
-
-J4: all open
-
-Default NOR flash boot switch setting:
- Sw3[1:8]: off on on off on on off off
- Sw4[1:8]: off off off on off off off off
- Sw6[1:8]: off on off on off on on off
- Sw7[1:8]: off on off off on off off off
- Sw8[1:8]: on off off off off off off off
-
-For NAND flash boot,set
-Sw4[1:4]: off on on on
-
-The default native ethernet setting is for RGMII mode.
-To use SGMII mode, set
-SW8[1:2]: OFF OFF
-SW7[6:7]: ON ON
-
-Memory Map
-----------
-0x0000_0000 0x7fff_ffff DDR 2G Cacheable
-0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
-0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
-0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
-
-0xe000_0000 0xe003_ffff BCSR 256K BCSR
-0xee00_0000 0xefff_ffff NOR flash 32M NOR flash
-0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M
-0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable
-0xffa0_0000 0xffaf_ffff NAND FLASH 1M non-cacheable
-0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
-
-Flashing u-boot Images
----------------
-To program the image in the boot flash bank:
-NOR flash boot:
- => tftp 1000000 u-boot.bin
- => protect off all
- => erase eff40000 efffffff
- => cp.b 1000000 eff40000 c0000
-
-NAND flash boot:
- => tftp 1000000 u-boot-nand.bin
- => nand erase 0 80000
- => nand write 1000000 0 80000
-
-Firmware ucode location
----------------------------------
-Microcode(ucode) to FMAN's IRAM is needed to make FMAN Ethernet work.
-u-boot loads ucode FLASH. The location for ucode:
-NOR Flash: 0xfe000000
-NAND Flash: 0x1f00000
-
-Using the Device Tree Source File
----------------------------------
-To create the DTB (Device Tree Binary) image file,
-use a command similar to this:
-
- dtc -b 0 -f -I dts -O dtb p1023rds.dts > p1023rds.dtb
-
-Likely, that .dts file will come from here;
-
- linux-2.6/arch/powerpc/boot/dts/p1023rds.dts
-or
- make p1023rds.dtb ARCH=powerpc
-in linux-2.6 directory.
-
-Booting Linux
--------------
-Place a linux uImage in the TFTP disk area.
-
- tftp 1000000 uImage
- tftp 2000000 rootfs.ext2.gz.uboot
- tftp c00000 p1023rds.dtb
- bootm 1000000 2000000 c00000
deleted file mode 100644
@@ -1,49 +0,0 @@
-/*
- * Copyright (C) 2011 Freescale Semiconductor, Inc.
- *
- * Authors: Chunhe Lan <b25806@freescale.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __BCSR_H_
-#define __BCSR_H_
-
-#include <common.h>
-
-/*
- * BCSR Bit definitions
- * BCSR 15 *
- 0 device insertion oriention
- 1 stack processor present
- 2 power supply shut down/normal operation
- 3 I2C bus0 drive enable
- 4 reserved
- 5:7 I2C bus0 select
- 5 - I2C_BUS_0_SS0
- 6 - I2C_BUS_0_SS1
- 7 - I2C_BUS_0_SS2
-*/
-
-/* BCSR register base address is 0xFX000020 */
-#define BCSR_BASE_REG_OFFSET 0x20
-#define BCSR_ACCESS_REG_ADDR (CONFIG_SYS_BCSR_BASE + BCSR_BASE_REG_OFFSET)
-
-#define BCSR15_DEV_INS_ORI 0x80
-#define BCSR15_STACK_PRO_PRE 0x40
-#define BCSR15_POWER_SUPPLY 0x20
-#define BCSR15_I2C_BUS0_EN 0x10
-#define BCSR15_I2C_BUS0_SEG0 0x00
-#define BCSR15_I2C_BUS0_SEG1 0x04
-#define BCSR15_I2C_BUS0_SEG2 0x02
-#define BCSR15_I2C_BUS0_SEG3 0x06
-#define BCSR15_I2C_BUS0_SEG4 0x01
-#define BCSR15_I2C_BUS0_SEG5 0x05
-#define BCSR15_I2C_BUS0_SEG6 0x03
-#define BCSR15_I2C_BUS0_SEG7 0x07
-#define BCSR15_I2C_BUS0_SEG_CLR 0x07
-#define BCSR19_SGMII_SEL_L 0x01
-
-/*BCSR Utils functions*/
-void fixup_i2c_bus0_sel_seg0(void);
-#endif /* __BCSR_H_ */
deleted file mode 100644
@@ -1,19 +0,0 @@
-/*
- * Copyright 2010-2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-struct law_entry law_table[] = {
- SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
- SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_4M,
- LAW_TRGT_IF_DPAA_SWP_SRAM),
- /* The LAW 0xe0000000 ~ 0xefffffff for BCSR and NOR flash */
- SET_LAW(CONFIG_SYS_BCSR_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
deleted file mode 100644
@@ -1,196 +0,0 @@
-/*
- * Copyright 2010-2012 Freescale Semiconductor, Inc.
- *
- * Authors: Roy Zang <tie-fei.zang@freescale.com>
- * Chunhe Lan <b25806@freescale.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <pci.h>
-#include <asm/io.h>
-#include <asm/cache.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_pci.h>
-#include <fsl_ddr_sdram.h>
-#include <asm/fsl_portals.h>
-#include <libfdt.h>
-#include <fdt_support.h>
-#include <netdev.h>
-#include <malloc.h>
-#include <fm_eth.h>
-#include <fsl_mdio.h>
-#include <miiphy.h>
-#include <phy.h>
-#include <asm/fsl_dtsec.h>
-
-#include "bcsr.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
- fsl_lbc_t *lbc = LBC_BASE_ADDR;
-
- /* Set ABSWP to implement conversion of addresses in the LBC */
- setbits_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
-
- return 0;
-}
-
-int checkboard(void)
-{
- u8 *bcsr = (u8 *)BCSR_ACCESS_REG_ADDR;
-
- printf("Board: P1023 RDS\n");
-
- clrbits_8(&bcsr[15], BCSR15_I2C_BUS0_SEG_CLR);
- setbits_8(&bcsr[15], BCSR15_I2C_BUS0_SEG0);
-
- return 0;
-}
-
-/* Fixed sdram init -- doesn't use serial presence detect. */
-phys_size_t fixed_sdram(void)
-{
-#ifndef CONFIG_SYS_RAMBOOT
- struct ccsr_ddr __iomem *ddr =
- (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
-
- set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1);
-
- out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS);
- out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG);
- out_be32(&ddr->cs1_bnds, CONFIG_SYS_DDR_CS1_BNDS);
- out_be32(&ddr->cs1_config, CONFIG_SYS_DDR_CS1_CONFIG);
- out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
- out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
- out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
- out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
- out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL2);
- out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1);
- out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2);
- out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL);
- out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT);
- out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL);
- out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4);
- out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5);
- out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CNTL);
- out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL);
- out_be32(&ddr->ddr_cdr1, CONFIG_SYS_DDR_CDR_1);
- out_be32(&ddr->ddr_cdr2, CONFIG_SYS_DDR_CDR_2);
- out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
-#endif
- return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024ul;
-}
-
-#ifdef CONFIG_PCI
-void pci_init_board(void)
-{
- fsl_pcie_init_board(0);
-}
-#endif
-
-int board_early_init_r(void)
-{
- const unsigned int flashbase = CONFIG_SYS_BCSR_BASE;
- const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
-
- /*
- * Remap Boot flash + BCSR region to caching-inhibited
- * so that flash can be erased properly.
- */
-
- /* Flush d-cache and invalidate i-cache of any FLASH data */
- flush_dcache();
- invalidate_icache();
-
- /* invalidate existing TLB entry for flash + bcsr */
- disable_tlb(flash_esel);
-
- set_tlb(1, flashbase, CONFIG_SYS_BCSR_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, flash_esel, BOOKE_PAGESZ_256M, 1);
-
- setup_portals();
-
- return 0;
-}
-
-unsigned long get_board_sys_clk(ulong dummy)
-{
- return gd->bus_clk;
-}
-
-unsigned long get_board_ddr_clk(ulong dummy)
-{
- return gd->mem_clk;
-}
-
-int board_eth_init(bd_t *bis)
-{
- u8 *bcsr = (u8 *)BCSR_ACCESS_REG_ADDR;
- ccsr_gur_t *gur = (ccsr_gur_t *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
- struct fsl_pq_mdio_info dtsec_mdio_info;
-
- /*
- * Need to set dTSEC 1 pin multiplexing to TSEC. The default setting
- * is not correct.
- */
- setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_TSEC1_1);
-
- dtsec_mdio_info.regs =
- (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
- dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
-
- /* Register the 1G MDIO bus */
- fsl_pq_mdio_init(bis, &dtsec_mdio_info);
-
- fm_info_set_phy_address(FM1_DTSEC1, CONFIG_SYS_FM1_DTSEC1_PHY_ADDR);
- fm_info_set_phy_address(FM1_DTSEC2, CONFIG_SYS_FM1_DTSEC2_PHY_ADDR);
-
- fm_info_set_mdio(FM1_DTSEC1,
- miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
- fm_info_set_mdio(FM1_DTSEC2,
- miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
-
- /* Make SERDES connected to SGMII by cleaing bcsr19[7] */
- if (fm_info_get_enet_if(FM1_DTSEC1) == PHY_INTERFACE_MODE_SGMII)
- clrbits_8(&bcsr[19], BCSR19_SGMII_SEL_L);
-
-#ifdef CONFIG_FMAN_ENET
- cpu_eth_init(bis);
-#endif
-
- return pci_eth_init(bis);
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-void ft_board_setup(void *blob, bd_t *bd)
-{
- phys_addr_t base;
- phys_size_t size;
-
- ft_cpu_setup(blob, bd);
-
- base = getenv_bootm_low();
- size = getenv_bootm_size();
-
- fdt_fixup_memory(blob, (u64)base, (u64)size);
-
- /* By default NOR is on, and NAND is disabled */
-#ifdef CONFIG_NAND_U_BOOT
- do_fixup_by_path_string(blob, "nor_flash", "status", "disabled");
- do_fixup_by_path_string(blob, "nand_flash", "status", "okay");
-#endif
-#ifdef CONFIG_HAS_FSL_DR_USB
- fdt_fixup_dr_usb(blob, bd);
-#endif
-
- fdt_fixup_fman_ethernet(blob);
-}
-#endif
deleted file mode 100644
@@ -1,102 +0,0 @@
-/*
- * Copyright 2010-2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
-
- /* TLB 1 */
- /* *I*** - Covers boot page */
- SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I,
- 0, 0, BOOKE_PAGESZ_4K, 1),
-
- /* *I*G* - CCSRBAR */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_4M, 1),
-
-#ifndef CONFIG_NAND_SPL
- /* *W*G* - BCSR and NOR flash on local bus*/
- /* This will be changed to *I*G* after relocation to RAM. */
- SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
- 0, 2, BOOKE_PAGESZ_256M, 1),
-
- /* *I*G* - PCI */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_1G, 1),
-
- /* *I*G* - PCI */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x40000000,
- CONFIG_SYS_PCIE3_MEM_PHYS + 0x40000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 4, BOOKE_PAGESZ_256M, 1),
-
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x50000000,
- CONFIG_SYS_PCIE3_MEM_PHYS + 0x50000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 5, BOOKE_PAGESZ_256M, 1),
-
- /* *I*G* - PCI I/O */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, CONFIG_SYS_PCIE3_IO_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 6, BOOKE_PAGESZ_256K, 1),
-
- /* Bman/Qman */
- SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 7, BOOKE_PAGESZ_1M, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000,
- CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 8, BOOKE_PAGESZ_1M, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
- 0, 9, BOOKE_PAGESZ_1M, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000,
- CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 10, BOOKE_PAGESZ_1M, 1),
-#endif
-
- /* *I*G - NAND */
- SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 11, BOOKE_PAGESZ_1M, 1),
-
-#ifdef CONFIG_SYS_RAMBOOT
- SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE,
- CONFIG_SYS_DDR_SDRAM_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 12, BOOKE_PAGESZ_1G, 1),
-
- SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
- CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 13, BOOKE_PAGESZ_1G, 1),
-#endif
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
@@ -862,8 +862,6 @@ Active powerpc mpc85xx - freescale p1022ds
Active powerpc mpc85xx - freescale p1022ds P1022DS_SDCARD P1022DS:SDCARD Timur Tabi <timur@freescale.com>
Active powerpc mpc85xx - freescale p1022ds P1022DS_SPIFLASH P1022DS:SPIFLASH Timur Tabi <timur@freescale.com>
Active powerpc mpc85xx - freescale p1023rdb P1023RDB - -
-Active powerpc mpc85xx - freescale p1023rds P1023RDS - Roy Zang <tie-fei.zang@freescale.com>
-Active powerpc mpc85xx - freescale p1023rds P1023RDS_NAND P1023RDS:NAND Roy Zang <tie-fei.zang@freescale.com>
Active powerpc mpc85xx - freescale p1_p2_rdb P1011RDB P1_P2_RDB:P1011RDB -
Active powerpc mpc85xx - freescale p1_p2_rdb P1011RDB_36BIT P1_P2_RDB:P1011RDB,36BIT -
Active powerpc mpc85xx - freescale p1_p2_rdb P1011RDB_36BIT_SDCARD P1_P2_RDB:P1011RDB,36BIT,SDCARD -
deleted file mode 100644
@@ -1,523 +0,0 @@
-/*
- * Copyright 2010-2012 Freescale Semiconductor, Inc.
- *
- * Authors: Roy Zang <tie-fei.zang@freescale.com>
- * Chunhe Lan <b25806@freescale.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * p1023rds board configuration file
- *
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#ifdef CONFIG_NAND
-#define CONFIG_NAND_U_BOOT
-#define CONFIG_RAMBOOT_NAND
-#endif
-
-#ifdef CONFIG_NAND_U_BOOT
-#define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000
-#define CONFIG_SYS_TEXT_BASE 0x11001000
-
-#ifdef CONFIG_NAND_SPL
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
-#else
-#define CONFIG_SYS_LDSCRIPT $(CPUDIR)/u-boot-nand.lds
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#endif /* CONFIG_NAND_SPL */
-#endif
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xeff40000
-#endif
-
-#ifndef CONFIG_SYS_MONITOR_BASE
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#endif
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
-#endif
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE /* BOOKE */
-#define CONFIG_E500 /* BOOKE e500 family */
-#define CONFIG_P1023
-#define CONFIG_P1023RDS
-#define CONFIG_MP /* support multiple processors */
-
-#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
-#define CONFIG_PCI /* Enable PCI/PCIE */
-#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
-#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */
-#define CONFIG_PCIE3 /* PCIE controler 3 (slot 3) */
-#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
-#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
-#define CONFIG_FSL_LAW /* Use common FSL init code */
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_clock_freq(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ 66666666
-#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_HWCONFIG
-
-#define CONFIG_ENABLE_36BIT_PHYS
-
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x1fffffff /* fix me, only 1G */
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
-
-#define CONFIG_SYS_LBC_LBCR 0x00000000 /* Implement conversion of
- addresses in the LBC */
-
-/* DDR Setup */
-#define CONFIG_VERY_BIG_RAM
-
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 2
-
-/* These are used when DDR doesn't use SPD. */
-#define CONFIG_SYS_SDRAM_SIZE 2048u /* DDR is 2GB */
-
-/* Default settings for "stable" mode */
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F
-#define CONFIG_SYS_DDR_CS1_BNDS 0x0040007F
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
-#define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302
-#define CONFIG_SYS_DDR_TIMING_3 0x00020000
-#define CONFIG_SYS_DDR_TIMING_0 0x40110104
-#define CONFIG_SYS_DDR_TIMING_1 0x5C59E544
-#define CONFIG_SYS_DDR_TIMING_2 0x0fA888CA
-#define CONFIG_SYS_DDR_MODE_1 0x00441210
-#define CONFIG_SYS_DDR_MODE_2 0x00000000
-#define CONFIG_SYS_DDR_MODE_CTRL 0x00000000
-#define CONFIG_SYS_DDR_INTERVAL 0x0A280100
-#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
-#define CONFIG_SYS_DDR_CLK_CTRL 0x01800000
-#define CONFIG_SYS_DDR_TIMING_4 0x00000001
-#define CONFIG_SYS_DDR_TIMING_5 0x01401400
-#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600
-#define CONFIG_SYS_DDR_WRLVL_CNTL 0x8675F605
-#define CONFIG_SYS_DDR_CONTROL 0xC70C0008 /* Type = DDR3: No Interleaving */
-#define CONFIG_SYS_DDR_CONTROL2 0x24401010
-#define CONFIG_SYS_DDR_CDR1 0x00000000
-#define CONFIG_SYS_DDR_CDR2 0x00000000
-
-#define CONFIG_SYS_DDR_ERR_INT_EN 0x00000000
-#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
-#define CONFIG_SYS_DDR_SBE 0x00000000
-
-/* Settings that differ for "performance" mode */
-#define CONFIG_SYS_DDR_CS0_BNDS_PERF 0x0000007F /* Interleaving Enabled */
-#define CONFIG_SYS_DDR_CS1_BNDS_PERF 0x00000000 /* Interleaving Enabled */
-#define CONFIG_SYS_DDR_CS1_CONFIG_PERF 0x80014302
-#define CONFIG_SYS_DDR_TIMING_1_PERF 0x5C58E544
-#define CONFIG_SYS_DDR_TIMING_2_PERF 0x0FA888CA
-/* Type = DDR3: cs0-cs1 interleaving */
-#define CONFIG_SYS_DDR_CONTROL_PERF 0xC70C4008
-#define CONFIG_SYS_DDR_CDR_1 0x00000000
-#define CONFIG_SYS_DDR_CDR_2 0x00000000
-
-
-/*
- * Memory map
- *
- * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
- * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
- * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
- * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
- *
- * Localbus non-cacheable
- * 0xe000_0000 0xe003_ffff BCSR 256K BCSR
- * 0xee00_0000 0xefff_ffff NOR flash 32M NOR flash
- * 0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M
- * 0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable
- * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable
- * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
- */
-
-/*
- * Local Bus Definitions
- */
-#define CONFIG_SYS_BCSR_BASE 0xe0000000 /* start of on board FPGA */
-#define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE
-
-#ifndef CONFIG_NAND
-#define CONFIG_SYS_FLASH_BASE 0xee000000 /* start of FLASH 32M */
-
-#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
- | BR_PS_16 | BR_V)
-#define CONFIG_FLASH_OR_PRELIM 0xfe000ff7
-
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#else
-#define CONFIG_SYS_NO_FLASH
-#endif
-
-#if defined(CONFIG_SYS_SPL) || defined(CONFIG_RAMBOOT_NAND)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f function */
-#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
-
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */
-
-#ifndef CONFIG_NAND_SPL
-#define CONFIG_SYS_NAND_BASE 0xffa00000
-#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
-#else
-#define CONFIG_SYS_NAND_BASE 0xfff00000
-#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
-#endif
-
-#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
-
-/* NAND boot: 4K NAND loader config */
-#define CONFIG_SYS_NAND_SPL_SIZE 0x1000
-#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) + CONFIG_SYS_NAND_SPL_SIZE)
-#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000 - CONFIG_SYS_NAND_SPL_SIZE)
-#define CONFIG_SYS_NAND_U_BOOT_START 0x11000000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (0)
-#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
-#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000)
-
-/* NAND flash config */
-#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
- | BR_PS_8 /* Port Size = 8bit */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_NAND_OR_PRELIM (0xFFF80000 /* length 32K */ \
- | OR_FCM_CSCT \
- | OR_FCM_CST \
- | OR_FCM_CHT \
- | OR_FCM_SCY_1 \
- | OR_FCM_TRLX \
- | OR_FCM_EHTR)
-
-#ifdef CONFIG_RAMBOOT_NAND
-/* NAND Base Address */
-#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM
-#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-/* chip select 1 - BCSR */
-#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \
- | BR_MS_GPCM | BR_PS_8 | BR_V)
-#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \
- | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \
- | OR_GPCM_EAD)
-#else
-#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
-#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
-/* chip select 1 - BCSR */
-#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \
- | BR_MS_GPCM | BR_PS_8 | BR_V)
-#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \
- | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \
- | OR_GPCM_EAD)
-#endif
-
-/* Serial Port
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#ifdef CONFIG_NAND_SPL
-#define CONFIG_NS16550_MIN_FUNCTIONS
-#endif
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51
-
-/*
- * I2C2 EEPROM
- */
-#define CONFIG_ID_EEPROM
-#ifdef CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#endif
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_BUS_NUM 0
-
-#define CONFIG_CMD_I2C
-
-/*
- * eSPI - Enhanced SPI
- */
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_ATMEL
-
-#define CONFIG_HARD_SPI
-#define CONFIG_FSL_ESPI
-
-#define CONFIG_CMD_SF
-#define CONFIG_SF_DEFAULT_SPEED 10000000
-#define CONFIG_SF_DEFAULT_MODE 0
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-/* controller 3, Slot 1, tgtid 3, Base address b000 */
-#define CONFIG_SYS_PCIE3_NAME "Slot 3"
-#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
-#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
-#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
-#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
-#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
-
-/* controller 2, direct to uli, tgtid 2, Base address 9000 */
-#define CONFIG_SYS_PCIE2_NAME "Slot 2"
-#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
-
-/* controller 1, Slot 2, tgtid 1, Base address a000 */
-#define CONFIG_SYS_PCIE1_NAME "Slot 1"
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-
-#if defined(CONFIG_PCI)
-#define CONFIG_E1000 /* Defind e1000 pci Ethernet card */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#endif /* CONFIG_PCI */
-
-/*
- * Environment
- */
-#define CONFIG_ENV_OVERWRITE
-
-#if defined(CONFIG_SYS_RAMBOOT)
-#if defined(CONFIG_RAMBOOT_NAND)
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
-#else
-#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x4000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif
-#else
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
-#endif
-
-#define CONFIG_LOADS_ECHO /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_SETEXPR
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
-#endif
-
-/*
- * USB
- */
-#define CONFIG_HAS_FSL_DR_USB
-#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_USB_STORAGE
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_UBOOTPATH (u-boot.bin) /* U-Boot image on TFTP server */
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 1000000
-
-#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
-
-#define CONFIG_BAUDRATE 115200
-
-/* Qman/Bman */
-#define CONFIG_SYS_DPAA_QBMAN /* support Q/Bman */
-#define CONFIG_SYS_QMAN_MEM_BASE 0xff000000
-#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
-#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
-#define CONFIG_SYS_BMAN_MEM_BASE 0xff200000
-#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
-#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
-
-/* For FM */
-#define CONFIG_SYS_DPAA_FMAN
-#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
-
-#ifdef CONFIG_SYS_DPAA_FMAN
-#define CONFIG_FMAN_ENET
-#define CONFIG_PHY_MARVELL
-#endif
-
-#ifndef CONFIG_NAND
-/* Default address of microcode for the Linux Fman driver */
-/* QE microcode/firmware address */
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
-#else
-#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_FMAN_FW_ADDR 0x1f00000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
-#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2
-#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x7
-
-#define CONFIG_SYS_TBIPA_VALUE 8
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_ETHPRIME "FM1@DTSEC1"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
-
-#endif /* __CONFIG_H */
deleted file mode 100644
@@ -1,87 +0,0 @@
-#
-# Copyright 2010-2011 Freescale Semiconductor, Inc.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-PAD_TO := 0xfff01000
-
-nandobj := $(objtree)/nand_spl/
-
-LDSCRIPT= $(srctree)/$(CPUDIR)/u-boot-nand_spl.lds
-LDFLAGS := -T $(nandobj)u-boot-nand_spl.lds -Ttext $(CONFIG_SYS_TEXT_BASE_SPL) \
- $(LDFLAGS) $(LDFLAGS_FINAL)
-asflags-y += -DCONFIG_NAND_SPL
-ccflags-y += -DCONFIG_NAND_SPL
-
-SOBJS = start.o resetvec.o
-COBJS = cache.o cpu_init_early.o spl_minimal.o fsl_law.o law.o \
- nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o
-
-OBJS := $(addprefix $(obj)/,$(SOBJS) $(COBJS))
-__OBJS := $(SOBJS) $(COBJS)
-LNDIR := $(nandobj)board/$(BOARDDIR)
-
-targets += $(__OBJS)
-
-all: $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
-
-$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl
- $(OBJCOPY) $(OBJCOPYFLAGS) --pad-to=$(PAD_TO) -O binary $< $@
-
-$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl
- $(OBJCOPY) $(OBJCOPYFLAGS) -O binary $< $@
-
-$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot-nand_spl.lds
- cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \
- -Map $(nandobj)u-boot-spl.map -o $@
-
-$(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT)
- $(CPP) $(cpp_flags) $(LDPPFLAGS) -I$(nandobj)/board/$(BOARDDIR) \
- -ansi -D__ASSEMBLY__ -P - <$< >$@
-
-# create symbolic links for common files
-
-$(obj)/cache.c:
- @rm -f $@
- ln -sf $(srctree)/arch/powerpc/lib/cache.c $@
-
-$(obj)/cpu_init_early.c:
- @rm -f $@
- ln -sf $(srctree)/$(CPUDIR)/cpu_init_early.c $@
-
-$(obj)/spl_minimal.c:
- @rm -f $@
- ln -sf $(srctree)/$(CPUDIR)/spl_minimal.c $@
-
-$(obj)/fsl_law.c:
- @rm -f $@
- ln -sf $(srctree)/arch/powerpc/cpu/mpc8xxx/law.c $@
-
-$(obj)/law.c:
- @rm -f $@
- ln -sf $(srctree)/board/$(BOARDDIR)/law.c $@
-
-$(obj)/nand_boot_fsl_elbc.c:
- @rm -f $@
- ln -sf $(srctree)/nand_spl/nand_boot_fsl_elbc.c $@
-
-$(obj)/ns16550.c:
- @rm -f $@
- ln -sf $(srctree)/drivers/serial/ns16550.c $@
-
-$(obj)/resetvec.S:
- @rm -f $@
- ln -s $(srctree)/$(CPUDIR)/resetvec.S $@
-
-$(obj)/start.S:
- @rm -f $@
- ln -sf $(srctree)/$(CPUDIR)/start.S $@
-
-$(obj)/tlb.c:
- @rm -f $@
- ln -sf $(srctree)/$(CPUDIR)/tlb.c $@
-
-$(obj)/tlb_table.c:
- @rm -f $@
- ln -sf $(srctree)/board/$(BOARDDIR)/tlb.c $@
deleted file mode 100644
@@ -1,96 +0,0 @@
-/*
- * Copyright 2010-2011 Freescale Semiconductor, Inc.
- * Author: Roy Zang <tie-fei.zang@freescale.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ns16550.h>
-#include <asm/io.h>
-#include <nand.h>
-#include <asm/fsl_law.h>
-#include <fsl_ddr_sdram.h>
-#include <asm/global_data.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* Fixed sdram init -- doesn't use serial presence detect. */
-void sdram_init(void)
-{
- struct ccsr_ddr __iomem *ddr =
- (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
-
- set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1);
-
- __raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds);
- __raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config);
- __raw_writel(CONFIG_SYS_DDR_CS1_BNDS, &ddr->cs1_bnds);
- __raw_writel(CONFIG_SYS_DDR_CS1_CONFIG, &ddr->cs1_config);
- __raw_writel(CONFIG_SYS_DDR_TIMING_3, &ddr->timing_cfg_3);
- __raw_writel(CONFIG_SYS_DDR_TIMING_0, &ddr->timing_cfg_0);
- __raw_writel(CONFIG_SYS_DDR_TIMING_1, &ddr->timing_cfg_1);
- __raw_writel(CONFIG_SYS_DDR_TIMING_2, &ddr->timing_cfg_2);
- __raw_writel(CONFIG_SYS_DDR_CONTROL2, &ddr->sdram_cfg_2);
- __raw_writel(CONFIG_SYS_DDR_MODE_1, &ddr->sdram_mode);
- __raw_writel(CONFIG_SYS_DDR_MODE_2, &ddr->sdram_mode_2);
- __raw_writel(CONFIG_SYS_DDR_INTERVAL, &ddr->sdram_interval);
- __raw_writel(CONFIG_SYS_DDR_DATA_INIT, &ddr->sdram_data_init);
- __raw_writel(CONFIG_SYS_DDR_CLK_CTRL, &ddr->sdram_clk_cntl);
- __raw_writel(CONFIG_SYS_DDR_TIMING_4, &ddr->timing_cfg_4);
- __raw_writel(CONFIG_SYS_DDR_TIMING_5, &ddr->timing_cfg_5);
- __raw_writel(CONFIG_SYS_DDR_ZQ_CNTL, &ddr->ddr_zq_cntl);
- __raw_writel(CONFIG_SYS_DDR_WRLVL_CNTL, &ddr->ddr_wrlvl_cntl);
- __raw_writel(CONFIG_SYS_DDR_CDR_1, &ddr->ddr_cdr1);
- __raw_writel(CONFIG_SYS_DDR_CDR_2, &ddr->ddr_cdr2);
- /* Set, but do not enable the memory */
- __raw_writel(CONFIG_SYS_DDR_CONTROL & ~SDRAM_CFG_MEM_EN, &ddr->sdram_cfg);
-
- asm volatile("sync;isync");
- udelay(500);
-
- /* Let the controller go */
- out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN);
-}
-
-void board_init_f(ulong bootflag)
-{
- u32 plat_ratio;
- ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
-
- /* initialize selected port with appropriate baud rate */
- plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
- plat_ratio >>= 1;
- gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
- NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
- gd->bus_clk / 16 / CONFIG_BAUDRATE);
-
- puts("\nNAND boot... ");
- /* Initialize the DDR3 */
- sdram_init();
- /* copy code to RAM and jump to it - this should not return */
- /* NOTE - code has to be copied out of NAND buffer before
- * other blocks can be read.
- */
- relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, 0,
- CONFIG_SYS_NAND_U_BOOT_RELOC);
-}
-
-void board_init_r(gd_t *gd, ulong dest_addr)
-{
- nand_boot();
-}
-
-void putc(char c)
-{
- if (c == '\n')
- NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
-
- NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
-}
-
-void puts(const char *str)
-{
- while (*str)
- putc(*str++);
-}
Since P1023RDS is no longer supported/manufactured by Freescale, we clean up P1023RDS related code. Since P1023RDB is still supported by Freescale, we keep P1023RDB releated code. Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com> --- board/freescale/p1023rds/Makefile | 9 - board/freescale/p1023rds/README | 101 ----- board/freescale/p1023rds/bcsr.h | 49 --- board/freescale/p1023rds/law.c | 19 - board/freescale/p1023rds/p1023rds.c | 196 ---------- board/freescale/p1023rds/tlb.c | 102 ----- boards.cfg | 2 - include/configs/P1023RDS.h | 523 -------------------------- nand_spl/board/freescale/p1023rds/Makefile | 87 ----- nand_spl/board/freescale/p1023rds/nand_boot.c | 96 ----- 10 files changed, 1184 deletions(-) delete mode 100644 board/freescale/p1023rds/Makefile delete mode 100644 board/freescale/p1023rds/README delete mode 100644 board/freescale/p1023rds/bcsr.h delete mode 100644 board/freescale/p1023rds/law.c delete mode 100644 board/freescale/p1023rds/p1023rds.c delete mode 100644 board/freescale/p1023rds/tlb.c delete mode 100644 include/configs/P1023RDS.h delete mode 100644 nand_spl/board/freescale/p1023rds/Makefile delete mode 100644 nand_spl/board/freescale/p1023rds/nand_boot.c