@@ -208,27 +208,22 @@ static int pci_write(struct pci_bus *bus, unsigned int devfn, int where,
static int intel_mid_pci_irq_enable(struct pci_dev *dev)
{
- u8 pin;
- struct io_apic_irq_attr irq_attr;
+ int polarity;
- pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin);
+ if (intel_mid_identify_cpu() == INTEL_MID_CPU_CHIP_TANGIER)
+ polarity = 0; /* active high */
+ else
+ polarity = 1; /* active low */
/*
* MRST only have IOAPIC, the PCI irq lines are 1:1 mapped to
* IOAPIC RTE entries, so we just enable RTE for the device.
*/
+ if (mp_set_gsi_attr(dev->irq, 1, polarity, dev_to_node(&dev->dev)))
+ return -EBUSY;
if (mp_map_gsi_to_irq(dev->irq, IOAPIC_MAP_ALLOC) < 0)
return -EBUSY;
- irq_attr.ioapic = mp_find_ioapic(dev->irq);
- irq_attr.ioapic_pin = dev->irq;
- irq_attr.trigger = 1; /* level */
- if (intel_mid_identify_cpu() == INTEL_MID_CPU_CHIP_TANGIER)
- irq_attr.polarity = 0; /* active high */
- else
- irq_attr.polarity = 1; /* active low */
- io_apic_set_pci_routing(&dev->dev, dev->irq, &irq_attr);
-
return 0;
}
@@ -432,9 +432,8 @@ static int __init sfi_parse_devs(struct sfi_table_header *table)
struct sfi_table_simple *sb;
struct sfi_device_table_entry *pentry;
struct devs_id *dev = NULL;
- int num, i;
- int ioapic;
- struct io_apic_irq_attr irq_attr;
+ int num, i, ret;
+ int polarity;
sb = (struct sfi_table_simple *)table;
num = SFI_GET_NUM_ENTRIES(sb, struct sfi_device_table_entry);
@@ -448,37 +447,30 @@ static int __init sfi_parse_devs(struct sfi_table_header *table)
* devices, but they have separate RTE entry in IOAPIC
* so we have to enable them one by one here
*/
- ioapic = mp_find_ioapic(irq);
- if (ioapic >= 0) {
- irq_attr.ioapic = ioapic;
- irq_attr.ioapic_pin = irq;
- irq_attr.trigger = 1;
- if (intel_mid_identify_cpu() ==
- INTEL_MID_CPU_CHIP_TANGIER) {
- if (!strncmp(pentry->name,
- "r69001-ts-i2c", 13))
- /* active low */
- irq_attr.polarity = 1;
- else if (!strncmp(pentry->name,
- "synaptics_3202", 14))
- /* active low */
- irq_attr.polarity = 1;
- else if (irq == 41)
- /* fast_int_1 */
- irq_attr.polarity = 1;
- else
- /* active high */
- irq_attr.polarity = 0;
- } else {
- /* PNW and CLV go with active low */
- irq_attr.polarity = 1;
- }
- WARN_ON(mp_map_gsi_to_irq(irq,
- IOAPIC_MAP_ALLOC) < 0);
- io_apic_set_pci_routing(NULL, irq, &irq_attr);
+ if (intel_mid_identify_cpu() ==
+ INTEL_MID_CPU_CHIP_TANGIER) {
+ if (!strncmp(pentry->name, "r69001-ts-i2c", 13))
+ /* active low */
+ polarity = 1;
+ else if (!strncmp(pentry->name,
+ "synaptics_3202", 14))
+ /* active low */
+ polarity = 1;
+ else if (irq == 41)
+ /* fast_int_1 */
+ polarity = 1;
+ else
+ /* active high */
+ polarity = 0;
+ } else {
+ /* PNW and CLV go with active low */
+ polarity = 1;
}
- } else {
- irq = 0; /* No irq */
+
+ ret = mp_set_gsi_attr(irq, 1, polarity, NUMA_NO_NODE);
+ if (ret == 0)
+ ret = mp_map_gsi_to_irq(irq, IOAPIC_MAP_ALLOC);
+ WARN_ON(ret < 0);
}
dev = get_device_id(pentry->type, pentry->name);
@@ -71,7 +71,9 @@ static int __init sfi_parse_cpus(struct sfi_table_header *table)
#endif /* CONFIG_X86_LOCAL_APIC */
#ifdef CONFIG_X86_IO_APIC
-static struct irq_domain_ops sfi_ioapic_irqdomain_ops;
+static struct irq_domain_ops sfi_ioapic_irqdomain_ops = {
+ .map = mp_irqdomain_map,
+};
static struct irq_domain *sfi_ioapic_create_irqdomain(int ioapic, void *arg)
{
Refine SFI to use common irqdomain map interface to program IOAPIC pins, so we can unify the callsite to progam IOAPIC pins. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> --- arch/x86/pci/intel_mid_pci.c | 19 +++++------- arch/x86/platform/intel-mid/sfi.c | 58 ++++++++++++++++--------------------- arch/x86/platform/sfi/sfi.c | 4 ++- 3 files changed, 35 insertions(+), 46 deletions(-)