@@ -706,9 +706,7 @@ static s32 igb_check_for_link_82575(struct e1000_hw *hw)
s32 ret_val;
u16 speed, duplex;
- /* SGMII link check is done through the PCS register. */
- if ((hw->phy.media_type != e1000_media_type_copper) ||
- (igb_sgmii_active_82575(hw))) {
+ if (hw->phy.media_type != e1000_media_type_copper) {
ret_val = igb_get_pcs_speed_and_duplex_82575(hw, &speed,
&duplex);
/*
@@ -723,6 +721,7 @@ static s32 igb_check_for_link_82575(struct e1000_hw *hw)
return ret_val;
}
+
/**
* igb_get_pcs_speed_and_duplex_82575 - Retrieve current speed/duplex
* @hw: pointer to the HW structure
@@ -788,13 +787,23 @@ static s32 igb_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw, u16 *speed,
void igb_shutdown_serdes_link_82575(struct e1000_hw *hw)
{
u32 reg;
+ u16 eeprom_data = 0;
if (hw->phy.media_type != e1000_media_type_internal_serdes ||
igb_sgmii_active_82575(hw))
return;
- /* if the management interface is not enabled, then power down */
- if (!igb_enable_mng_pass_thru(hw)) {
+ if (hw->bus.func == E1000_FUNC_0)
+ hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
+ else if (hw->bus.func == E1000_FUNC_1)
+ hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
+
+ /*
+ * If APM is not enabled in the EEPROM and management interface is
+ * not enabled, then power down.
+ */
+ if (!(eeprom_data & E1000_NVM_APME_82575) &&
+ !igb_enable_mng_pass_thru(hw)) {
/* Disable PCS to turn off link */
reg = rd32(E1000_PCS_CFG0);
reg &= ~E1000_PCS_CFG_PCS_EN;
@@ -1010,10 +1019,13 @@ out:
}
/**
- * igb_setup_serdes_link_82575 - Setup link for fiber/serdes
+ * igb_setup_serdes_link_82575 - Setup link for serdes
* @hw: pointer to the HW structure
*
- * Configures speed and duplex for fiber and serdes links.
+ * Configure the physical coding sub-layer (PCS) link. The PCS link is
+ * used on copper connections where the serialized gigabit media independent
+ * interface (sgmii), or serdes fiber is being used. Configures the link
+ * for auto-negotiation or forces speed/duplex.
**/
static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
{
@@ -1086,18 +1098,27 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
*/
if (hw->mac.autoneg || igb_sgmii_active_82575(hw)) {
/* Set PCS register for autoneg */
- reg |= E1000_PCS_LCTL_FSV_1000 | /* Force 1000 */
- E1000_PCS_LCTL_FDV_FULL | /* SerDes Full duplex */
- E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
- E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */
+ reg |= E1000_PCS_LCTL_FSV_1000 | /* Force 1000 */
+ E1000_PCS_LCTL_FDV_FULL | /* SerDes Full dplx */
+ E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
+ E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */
hw_dbg("Configuring Autoneg; PCS_LCTL = 0x%08X\n", reg);
} else {
- /* Set PCS register for forced speed */
- reg |= E1000_PCS_LCTL_FLV_LINK_UP | /* Force link up */
- E1000_PCS_LCTL_FSV_1000 | /* Force 1000 */
- E1000_PCS_LCTL_FDV_FULL | /* SerDes Full duplex */
- E1000_PCS_LCTL_FSD | /* Force Speed */
- E1000_PCS_LCTL_FORCE_LINK; /* Force Link */
+ /* Check for duplex first */
+ if (hw->mac.forced_speed_duplex & E1000_ALL_FULL_DUPLEX)
+ reg |= E1000_PCS_LCTL_FDV_FULL;
+
+ /* No need to check for 1000/full since the spec states that
+ * it requires autoneg to be enabled */
+ /* Now set speed */
+ if (hw->mac.forced_speed_duplex & E1000_ALL_100_SPEED)
+ reg |= E1000_PCS_LCTL_FSV_100;
+
+ /* Force speed and force link */
+ reg |= E1000_PCS_LCTL_FSD |
+ E1000_PCS_LCTL_FORCE_LINK |
+ E1000_PCS_LCTL_FLV_LINK_UP;
+
hw_dbg("Configuring Forced Link; PCS_LCTL = 0x%08X\n", reg);
}
@@ -167,6 +167,7 @@ struct e1000_adv_tx_context_desc {
#define E1000_DCA_TXCTRL_CPUID_SHIFT 24 /* Tx CPUID now in the last byte */
#define E1000_DCA_RXCTRL_CPUID_SHIFT 24 /* Rx CPUID now in the last byte */
+#define E1000_NVM_APME_82575 0x0400
#define MAX_NUM_VFS 8
#define E1000_DTXSWC_VMDQ_LOOPBACK_EN (1 << 31) /* global VF LB enable */
@@ -50,6 +50,7 @@ struct e1000_hw;
#define E1000_REVISION_2 2
#define E1000_REVISION_4 4
+#define E1000_FUNC_0 0
#define E1000_FUNC_1 1
enum e1000_mac_type {