diff mbox

[U-Boot] imx: ventana: add HDMI and LVDS display capability

Message ID 1398465547-2433-1-git-send-email-tharvey@gateworks.com
State Accepted
Delegated to: Stefano Babic
Headers show

Commit Message

Tim Harvey April 25, 2014, 10:39 p.m. UTC 
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
 board/gateworks/gw_ventana/gw_ventana.c | 134 ++++++++++++++++++++++++++++++++
 include/configs/gw_ventana.h            |  16 ++++
 2 files changed, 150 insertions(+)

Comments

Stefano Babic May 9, 2014, 1:13 p.m. UTC | #1 
On 26/04/2014 00:39, Tim Harvey wrote:
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> ---


Applied after fixing the following checkpatch errors:

ERROR: return is not a function, parentheses are not required
#45: FILE: board/gateworks/gw_ventana/gw_ventana.c:383:
+	return ((0 == i2c_set_bus_num(dev->bus))

CHECK: Logical continuations should be on the previous line
#46: FILE: board/gateworks/gw_ventana/gw_ventana.c:384:
+	return ((0 == i2c_set_bus_num(dev->bus))
+		&&

total: 1 errors, 0 warnings, 1 checks, 180 lines checked

Best regards,
Stefano Babic
diff mbox

Patch

diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c
index 79b3e01..f5b9f90 100644
--- a/board/gateworks/gw_ventana/gw_ventana.c
+++ b/board/gateworks/gw_ventana/gw_ventana.c
@@ -12,6 +12,7 @@ 
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/iomux.h>
 #include <asm/arch/mx6-pins.h>
+#include <asm/arch/mxc_hdmi.h>
 #include <asm/arch/crm_regs.h>
 #include <asm/arch/sys_proto.h>
 #include <asm/gpio.h>
@@ -19,6 +20,7 @@ 
 #include <asm/imx-common/mxc_i2c.h>
 #include <asm/imx-common/boot_mode.h>
 #include <asm/imx-common/sata.h>
+#include <asm/imx-common/video.h>
 #include <jffs2/load_kernel.h>
 #include <hwconfig.h>
 #include <i2c.h>
@@ -369,6 +371,135 @@  int board_eth_init(bd_t *bis)
 	return 0;
 }
 
+#if defined(CONFIG_VIDEO_IPUV3)
+
+static void enable_hdmi(struct display_info_t const *dev)
+{
+	imx_enable_hdmi_phy();
+}
+
+static int detect_i2c(struct display_info_t const *dev)
+{
+	return ((0 == i2c_set_bus_num(dev->bus))
+		&&
+		(0 == i2c_probe(dev->addr)));
+}
+
+static void enable_lvds(struct display_info_t const *dev)
+{
+	struct iomuxc *iomux = (struct iomuxc *)
+				IOMUXC_BASE_ADDR;
+
+	/* set CH0 data width to 24bit (IOMUXC_GPR2:5 0=18bit, 1=24bit) */
+	u32 reg = readl(&iomux->gpr[2]);
+	reg |= IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT;
+	writel(reg, &iomux->gpr[2]);
+
+	/* Enable Backlight */
+	imx_iomux_v3_setup_pad(MX6_PAD_SD1_CMD__GPIO1_IO18 |
+			       MUX_PAD_CTRL(NO_PAD_CTRL));
+	gpio_direction_output(IMX_GPIO_NR(1, 18), 1);
+}
+
+struct display_info_t const displays[] = {{
+	/* HDMI Output */
+	.bus	= -1,
+	.addr	= 0,
+	.pixfmt	= IPU_PIX_FMT_RGB24,
+	.detect	= detect_hdmi,
+	.enable	= enable_hdmi,
+	.mode	= {
+		.name           = "HDMI",
+		.refresh        = 60,
+		.xres           = 1024,
+		.yres           = 768,
+		.pixclock       = 15385,
+		.left_margin    = 220,
+		.right_margin   = 40,
+		.upper_margin   = 21,
+		.lower_margin   = 7,
+		.hsync_len      = 60,
+		.vsync_len      = 10,
+		.sync           = FB_SYNC_EXT,
+		.vmode          = FB_VMODE_NONINTERLACED
+} }, {
+	/* Freescale MXC-LVDS1: HannStar HSD100PXN1-A00 w/ egalx_ts cont */
+	.bus	= 2,
+	.addr	= 0x4,
+	.pixfmt	= IPU_PIX_FMT_LVDS666,
+	.detect	= detect_i2c,
+	.enable	= enable_lvds,
+	.mode	= {
+		.name           = "Hannstar-XGA",
+		.refresh        = 60,
+		.xres           = 1024,
+		.yres           = 768,
+		.pixclock       = 15385,
+		.left_margin    = 220,
+		.right_margin   = 40,
+		.upper_margin   = 21,
+		.lower_margin   = 7,
+		.hsync_len      = 60,
+		.vsync_len      = 10,
+		.sync           = FB_SYNC_EXT,
+		.vmode          = FB_VMODE_NONINTERLACED
+} } };
+size_t display_count = ARRAY_SIZE(displays);
+
+static void setup_display(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int reg;
+
+	enable_ipu_clock();
+	imx_setup_hdmi();
+	/* Turn on LDB0,IPU,IPU DI0 clocks */
+	reg = __raw_readl(&mxc_ccm->CCGR3);
+	reg |= MXC_CCM_CCGR3_LDB_DI0_MASK;
+	writel(reg, &mxc_ccm->CCGR3);
+
+	/* set LDB0, LDB1 clk select to 011/011 */
+	reg = readl(&mxc_ccm->cs2cdr);
+	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+		 |MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+	reg |= (3<<MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
+	      |(3<<MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+	writel(reg, &mxc_ccm->cs2cdr);
+
+	reg = readl(&mxc_ccm->cscmr2);
+	reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
+	writel(reg, &mxc_ccm->cscmr2);
+
+	reg = readl(&mxc_ccm->chsccdr);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+	writel(reg, &mxc_ccm->chsccdr);
+
+	reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+	     |IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
+	     |IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
+	     |IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG
+	     |IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT
+	     |IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+	     |IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT
+	     |IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
+	     |IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
+	writel(reg, &iomux->gpr[2]);
+
+	reg = readl(&iomux->gpr[3]);
+	reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
+	    | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+	       <<IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
+	writel(reg, &iomux->gpr[3]);
+
+	/* Backlight CABEN on LVDS connector */
+	imx_iomux_v3_setup_pad(MX6_PAD_SD2_CLK__GPIO1_IO10 |
+			       MUX_PAD_CTRL(NO_PAD_CTRL));
+	gpio_direction_output(IMX_GPIO_NR(1, 10), 0);
+}
+#endif /* CONFIG_VIDEO_IPUV3 */
+
 /* read ventana EEPROM, check for validity, and return baseboard type */
 static int
 read_eeprom(void)
@@ -942,6 +1073,9 @@  int board_early_init_f(void)
 	setup_iomux_uart();
 	gpio_direction_output(GP_USB_OTG_PWR, 0); /* OTG power off */
 
+#if defined(CONFIG_VIDEO_IPUV3)
+	setup_display();
+#endif
 	return 0;
 }
 
diff --git a/include/configs/gw_ventana.h b/include/configs/gw_ventana.h
index 335f2ff..cd55495 100644
--- a/include/configs/gw_ventana.h
+++ b/include/configs/gw_ventana.h
@@ -194,6 +194,22 @@ 
 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
 #define CONFIG_USB_HUB_MIN_POWER_ON_DELAY 1200
 
+/* Framebuffer and LCD */
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_IPUV3
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_IPUV3_CLK          260000000
+#define CONFIG_CMD_HDMIDETECT
+#define CONFIG_CONSOLE_MUX
+#define CONFIG_IMX_HDMI
+#define CONFIG_IMX_VIDEO_SKIP
+
 /* serial console (ttymxc1,115200) */
 #define CONFIG_CONS_INDEX              1
 #define CONFIG_BAUDRATE                115200