@@ -23,6 +23,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/interrupt.h>
+#include <linux/irq.h>
#include <linux/gpio.h>
#include <linux/delay.h>
#include <linux/mutex.h>
@@ -970,8 +971,7 @@ static int at86rf230_irq_polarity(struct at86rf230_local *lp, int pol)
static int at86rf230_hw_init(struct at86rf230_local *lp)
{
- struct at86rf230_platform_data *pdata = lp->spi->dev.platform_data;
- int rc, irq_pol;
+ int rc, irq_pol, irq_type;
u8 status;
u8 csma_seed[2];
@@ -983,8 +983,9 @@ static int at86rf230_hw_init(struct at86rf230_local *lp)
if (rc)
return rc;
+ irq_type = irq_get_trigger_type(lp->spi->irq);
/* configure irq polarity, defaults to high active */
- if (pdata->irq_type & (IRQF_TRIGGER_FALLING | IRQF_TRIGGER_LOW))
+ if (irq_type & (IRQF_TRIGGER_FALLING | IRQF_TRIGGER_LOW))
irq_pol = IRQ_ACTIVE_LOW;
else
irq_pol = IRQ_ACTIVE_HIGH;
@@ -1032,7 +1033,6 @@ static struct at86rf230_platform_data *
at86rf230_get_pdata(struct spi_device *spi)
{
struct at86rf230_platform_data *pdata;
- const char *irq_type;
if (!IS_ENABLED(CONFIG_OF) || !spi->dev.of_node)
return spi->dev.platform_data;
@@ -1044,19 +1044,6 @@ at86rf230_get_pdata(struct spi_device *spi)
pdata->rstn = of_get_named_gpio(spi->dev.of_node, "reset-gpio", 0);
pdata->slp_tr = of_get_named_gpio(spi->dev.of_node, "sleep-gpio", 0);
- pdata->irq_type = IRQF_TRIGGER_RISING;
- of_property_read_string(spi->dev.of_node, "irq-type", &irq_type);
- if (!strcmp(irq_type, "level-high"))
- pdata->irq_type = IRQF_TRIGGER_HIGH;
- else if (!strcmp(irq_type, "level-low"))
- pdata->irq_type = IRQF_TRIGGER_LOW;
- else if (!strcmp(irq_type, "edge-rising"))
- pdata->irq_type = IRQF_TRIGGER_RISING;
- else if (!strcmp(irq_type, "edge-falling"))
- pdata->irq_type = IRQF_TRIGGER_FALLING;
- else
- dev_warn(&spi->dev, "wrong irq-type specified using edge-rising\n");
-
spi->dev.platform_data = pdata;
done:
return pdata;
@@ -1071,7 +1058,7 @@ static int at86rf230_probe(struct spi_device *spi)
u8 part = 0, version = 0, status;
irq_handler_t irq_handler;
work_func_t irq_worker;
- int rc;
+ int rc, irq_type;
const char *chip;
struct ieee802154_ops *ops = NULL;
@@ -1176,7 +1163,8 @@ static int at86rf230_probe(struct spi_device *spi)
dev->extra_tx_headroom = 0;
dev->flags = IEEE802154_HW_OMIT_CKSUM | IEEE802154_HW_AACK;
- if (pdata->irq_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
+ irq_type = irq_get_trigger_type(spi->irq);
+ if (irq_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
irq_worker = at86rf230_irqwork;
irq_handler = at86rf230_isr;
} else {
@@ -1203,7 +1191,7 @@ static int at86rf230_probe(struct spi_device *spi)
goto err_hw_init;
rc = request_irq(spi->irq, irq_handler,
- IRQF_SHARED | pdata->irq_type,
+ IRQF_SHARED | irq_type,
dev_name(&spi->dev), lp);
if (rc)
goto err_hw_init;
@@ -26,20 +26,6 @@ struct at86rf230_platform_data {
int rstn;
int slp_tr;
int dig2;
-
- /* Setting the irq_type will configure the driver to request
- * the platform irq trigger type according to the given value
- * and configure the interrupt polarity of the device to the
- * corresponding polarity.
- *
- * Allowed values are: IRQF_TRIGGER_RISING, IRQF_TRIGGER_FALLING,
- * IRQF_TRIGGER_HIGH and IRQF_TRIGGER_LOW
- *
- * Setting it to 0, the driver does not touch the trigger type
- * configuration of the interrupt and sets the interrupt polarity
- * of the device to high active (the default value).
- */
- int irq_type;
};
#endif
This patch removes the platform data for the irq_type. We use instead the irq_get_trigger_type function to get these flags which should already configured by the interrupt controller. Signed-off-by: Alexander Aring <alex.aring@gmail.com> --- drivers/net/ieee802154/at86rf230.c | 28 ++++++++-------------------- include/linux/spi/at86rf230.h | 14 -------------- 2 files changed, 8 insertions(+), 34 deletions(-)