@@ -664,75 +664,6 @@ static void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
}
/**
- * ixgbe_set_fiber_fixed_speed - Set module link speed for fixed fiber
- * @hw: pointer to hardware structure
- * @speed: link speed to set
- *
- * We set the module speed differently for fixed fiber. For other
- * multi-speed devices we don't have an error value so here if we
- * detect an error we just log it and exit.
- */
-static void ixgbe_set_fiber_fixed_speed(struct ixgbe_hw *hw,
- ixgbe_link_speed speed)
-{
- s32 status;
- u8 rs, eeprom_data;
-
- switch (speed) {
- case IXGBE_LINK_SPEED_10GB_FULL:
- /* one bit mask same as setting on */
- rs = IXGBE_SFF_SOFT_RS_SELECT_10G;
- break;
- case IXGBE_LINK_SPEED_1GB_FULL:
- rs = IXGBE_SFF_SOFT_RS_SELECT_1G;
- break;
- default:
- hw_dbg(hw, "Invalid fixed module speed\n");
- return;
- }
-
- /* Set RS0 */
- status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
- IXGBE_I2C_EEPROM_DEV_ADDR2,
- &eeprom_data);
- if (status) {
- hw_dbg(hw, "Failed to read Rx Rate Select RS0\n");
- goto out;
- }
-
- eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs;
-
- status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
- IXGBE_I2C_EEPROM_DEV_ADDR2,
- eeprom_data);
- if (status) {
- hw_dbg(hw, "Failed to write Rx Rate Select RS0\n");
- goto out;
- }
-
- /* Set RS1 */
- status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB,
- IXGBE_I2C_EEPROM_DEV_ADDR2,
- &eeprom_data);
- if (status) {
- hw_dbg(hw, "Failed to read Rx Rate Select RS1\n");
- goto out;
- }
-
- eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) & rs;
-
- status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB,
- IXGBE_I2C_EEPROM_DEV_ADDR2,
- eeprom_data);
- if (status) {
- hw_dbg(hw, "Failed to write Rx Rate Select RS1\n");
- goto out;
- }
-out:
- return;
-}
-
-/**
* ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
* @hw: pointer to hardware structure
* @speed: new link speed
@@ -842,10 +773,6 @@ static s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
/* Set the module link speed */
switch (hw->phy.media_type) {
- case ixgbe_media_type_fiber_fixed:
- ixgbe_set_fiber_fixed_speed(hw,
- IXGBE_LINK_SPEED_1GB_FULL);
- break;
case ixgbe_media_type_fiber:
esdp_reg &= ~IXGBE_ESDP_SDP5;
esdp_reg |= IXGBE_ESDP_SDP5_DIR;
@@ -73,7 +73,6 @@ bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
bool link_up;
switch (hw->phy.media_type) {
- case ixgbe_media_type_fiber_fixed:
case ixgbe_media_type_fiber:
hw->mac.ops.check_link(hw, &speed, &link_up, false);
/* if link is down, assume supported */
@@ -147,7 +146,6 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw)
goto out;
/* only backplane uses autoc so fall though */
- case ixgbe_media_type_fiber_fixed:
case ixgbe_media_type_fiber:
reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
@@ -2398,7 +2396,6 @@ void ixgbe_fc_autoneg(struct ixgbe_hw *hw)
switch (hw->phy.media_type) {
/* Autoneg flow control on fiber adapters */
- case ixgbe_media_type_fiber_fixed:
case ixgbe_media_type_fiber:
if (speed == IXGBE_LINK_SPEED_1GB_FULL)
ret_val = ixgbe_fc_autoneg_fiber(hw);
@@ -66,9 +66,6 @@
#define IXGBE_SFF_1GBASET_CAPABLE 0x8
#define IXGBE_SFF_10GBASESR_CAPABLE 0x10
#define IXGBE_SFF_10GBASELR_CAPABLE 0x20
-#define IXGBE_SFF_SOFT_RS_SELECT_MASK 0x8
-#define IXGBE_SFF_SOFT_RS_SELECT_10G 0x8
-#define IXGBE_SFF_SOFT_RS_SELECT_1G 0x0
#define IXGBE_SFF_ADDRESSING_MODE 0x4
#define IXGBE_SFF_QSFP_DA_ACTIVE_CABLE 0x1
#define IXGBE_SFF_QSFP_DA_PASSIVE_CABLE 0x8
@@ -80,7 +77,6 @@
#define IXGBE_I2C_EEPROM_STATUS_PASS 0x1
#define IXGBE_I2C_EEPROM_STATUS_FAIL 0x2
#define IXGBE_I2C_EEPROM_STATUS_IN_PROGRESS 0x3
-
/* Flow control defines */
#define IXGBE_TAF_SYM_PAUSE 0x400
#define IXGBE_TAF_ASM_PAUSE 0x800
@@ -2664,7 +2664,6 @@ enum ixgbe_sfp_type {
enum ixgbe_media_type {
ixgbe_media_type_unknown = 0,
ixgbe_media_type_fiber,
- ixgbe_media_type_fiber_fixed,
ixgbe_media_type_fiber_qsfp,
ixgbe_media_type_fiber_lco,
ixgbe_media_type_copper,