| Message ID | 1394128498-28420-2-git-send-email-lho@apm.com |
|---|---|
| State | Superseded, archived |
| Headers | show |
Hi, On Thursday 06 March 2014 11:24 PM, Loc Ho wrote: > This patch adds support for the APM X-Gene SoC 15Gbps Multi-purpose PHY. > This is the physical layer interface for the corresponding host > controller. Currently, only external clock and Gen3 SATA mode > are supported. Pls fix these checkpatch errors ERROR: code indent should use tabs where possible #413: FILE: drivers/phy/phy-xgene.c:293: + (((dst) & ~0x00000060) | (((u32) (src) << 5) & 0x00000060))$ WARNING: please, no spaces at the start of a line #413: FILE: drivers/phy/phy-xgene.c:293: + (((dst) & ~0x00000060) | (((u32) (src) << 5) & 0x00000060))$ ERROR: code indent should use tabs where possible #415: FILE: drivers/phy/phy-xgene.c:295: + (((dst) & ~0x00000006) | (((u32) (src) << 1) & 0x00000006))$ WARNING: please, no spaces at the start of a line #415: FILE: drivers/phy/phy-xgene.c:295: + (((dst) & ~0x00000006) | (((u32) (src) << 1) & 0x00000006))$ ERROR: code indent should use tabs where possible #685: FILE: drivers/phy/phy-xgene.c:565: + unsigned long deadline = jiffies + HZ;$ WARNING: please, no spaces at the start of a line #685: FILE: drivers/phy/phy-xgene.c:565: + unsigned long deadline = jiffies + HZ;$ ERROR: code indent should use tabs where possible #707: FILE: drivers/phy/phy-xgene.c:587: + unsigned long deadline = jiffies + HZ;$ WARNING: please, no spaces at the start of a line #707: FILE: drivers/phy/phy-xgene.c:587: + unsigned long deadline = jiffies + HZ;$ ERROR: code indent should use tabs where possible #932: FILE: drivers/phy/phy-xgene.c:812: + if (cmu_type == REF_CMU) {$ WARNING: please, no spaces at the start of a line #932: FILE: drivers/phy/phy-xgene.c:812: + if (cmu_type == REF_CMU) {$ ERROR: code indent should use tabs where possible #1309: FILE: drivers/phy/phy-xgene.c:1189: + * that is required to be calibrated.$ ERROR: code indent should use tabs where possible #1319: FILE: drivers/phy/phy-xgene.c:1199: + * resistors that are required to the calibrated.$ total: 7 errors, 5 warnings, 1765 lines checked Thanks Kishon > > Signed-off-by: Loc Ho <lho@apm.com> > Signed-off-by: Tuan Phan <tphan@apm.com> > Signed-off-by: Suman Tripathi <stripathi@apm.com> > --- > drivers/phy/Kconfig | 7 + > drivers/phy/Makefile | 2 + > drivers/phy/phy-xgene.c | 1750 +++++++++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 1759 insertions(+), 0 deletions(-) > create mode 100644 drivers/phy/phy-xgene.c > > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig > index afa2354..221a1b7 100644 > --- a/drivers/phy/Kconfig > +++ b/drivers/phy/Kconfig > @@ -64,4 +64,11 @@ config BCM_KONA_USB2_PHY > help > Enable this to support the Broadcom Kona USB 2.0 PHY. > > +config PHY_XGENE > + tristate "APM X-Gene 15Gbps PHY support" > + depends on HAS_IOMEM && OF && (ARM64 || COMPILE_TEST) > + select GENERIC_PHY > + help > + This option enables support for APM X-Gene SoC multi-purpose PHY. > + > endmenu > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile > index b57c253..dee70f4 100644 > --- a/drivers/phy/Makefile > +++ b/drivers/phy/Makefile > @@ -9,3 +9,5 @@ obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o > obj-$(CONFIG_PHY_MVEBU_SATA) += phy-mvebu-sata.o > obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o > obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o > +obj-$(CONFIG_PHY_XGENE) += phy-xgene.o > + > diff --git a/drivers/phy/phy-xgene.c b/drivers/phy/phy-xgene.c > new file mode 100644 > index 0000000..c9b6ad8 > --- /dev/null > +++ b/drivers/phy/phy-xgene.c > @@ -0,0 +1,1750 @@ > +/* > + * AppliedMicro X-Gene Multi-purpose PHY driver > + * > + * Copyright (c) 2014, Applied Micro Circuits Corporation > + * Author: Loc Ho <lho@apm.com> > + * Tuan Phan <tphan@apm.com> > + * Suman Tripathi <stripathi@apm.com> > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms of the GNU General Public License as published by the > + * Free Software Foundation; either version 2 of the License, or (at your > + * option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * You should have received a copy of the GNU General Public License > + * along with this program. If not, see <http://www.gnu.org/licenses/>. > + * > + * The APM X-Gene PHY consists of two PLL clock macro's (CMU) and lanes. > + * The first PLL clock macro is used for internal reference clock. The second > + * PLL clock macro is used to generate the clock for the PHY. This driver > + * configures the first PLL CMU, the second PLL CMU, and programs the PHY to > + * operate according to the mode of operation. The first PLL CMU is only > + * required if internal clock is enabled. > + * > + * Logical Layer Out Of HW module units: > + * > + * ----------------- > + * | Internal | |------| > + * | Ref PLL CMU |----| | ------------- --------- > + * ------------ ---- | MUX |-----|PHY PLL CMU|----| Serdes| > + * | | | | --------- > + * External Clock ------| | ------------- > + * |------| > + * > + * The Ref PLL CMU CSR (Configuration System Registers) is accessed > + * indirectly from the SDS offset at 0x2000. It is only required for > + * internal reference clock. > + * The PHY PLL CMU CSR is accessed indirectly from the SDS offset at 0x0000. > + * The Serdes CSR is accessed indirectly from the SDS offset at 0x0400. > + * > + * The Ref PLL CMU can be located within the same PHY IP or outside the PHY IP > + * due to shared Ref PLL CMU. For PHY with Ref PLL CMU shared with another IP, > + * it is located outside the PHY IP. This is the case for the PHY located > + * at 0x1f23a000 (SATA Port 4/5). For such PHY, another resource is required > + * to located the SDS/Ref PLL CMU module and its clock for that IP enabled. > + * > + * Currently, this driver only supports Gen3 SATA mode with external clock. > + */ > +#include <linux/module.h> > +#include <linux/platform_device.h> > +#include <linux/io.h> > +#include <linux/delay.h> > +#include <linux/phy/phy.h> > +#include <linux/clk.h> > + > +/* Max 2 lanes per a PHY unit */ > +#define MAX_LANE 2 > + > +/* Register offset inside the PHY */ > +#define SERDES_PLL_INDIRECT_OFFSET 0x0000 > +#define SERDES_PLL_REF_INDIRECT_OFFSET 0x2000 > +#define SERDES_INDIRECT_OFFSET 0x0400 > +#define SERDES_LANE_STRIDE 0x0200 > + > +/* Some default Serdes parameters */ > +#define DEFAULT_SATA_TXBOOST_GAIN { 0x1e, 0x1e, 0x1e } > +#define DEFAULT_SATA_TXEYEDIRECTION { 0x0, 0x0, 0x0 } > +#define DEFAULT_SATA_TXEYETUNING { 0xa, 0xa, 0xa } > +#define DEFAULT_SATA_SPD_SEL { 0x1, 0x3, 0x7 } > +#define DEFAULT_SATA_TXAMP { 0x8, 0x8, 0x8 } > +#define DEFAULT_SATA_TXCN1 { 0x2, 0x2, 0x2 } > +#define DEFAULT_SATA_TXCN2 { 0x0, 0x0, 0x0 } > +#define DEFAULT_SATA_TXCP1 { 0xa, 0xa, 0xa } > + > +#define SATA_SPD_SEL_GEN3 0x7 > +#define SATA_SPD_SEL_GEN2 0x3 > +#define SATA_SPD_SEL_GEN1 0x1 > + > +#define SSC_DISABLE 0 > +#define SSC_ENABLE 1 > + > +#define FBDIV_VAL_50M 0x77 > +#define REFDIV_VAL_50M 0x1 > +#define FBDIV_VAL_100M 0x3B > +#define REFDIV_VAL_100M 0x0 > + > +/* SATA Clock/Reset CSR */ > +#define SATACLKENREG 0x00000000 > +#define SATA0_CORE_CLKEN 0x00000002 > +#define SATA1_CORE_CLKEN 0x00000004 > +#define SATASRESETREG 0x00000004 > +#define SATA_MEM_RESET_MASK 0x00000020 > +#define SATA_MEM_RESET_RD(src) (((src) & 0x00000020) >> 5) > +#define SATA_SDS_RESET_MASK 0x00000004 > +#define SATA_CSR_RESET_MASK 0x00000001 > +#define SATA_CORE_RESET_MASK 0x00000002 > +#define SATA_PMCLK_RESET_MASK 0x00000010 > +#define SATA_PCLK_RESET_MASK 0x00000008 > + > +/* SDS CSR used for PHY Indirect access */ > +#define SATA_ENET_SDS_PCS_CTL0 0x00000000 > +#define REGSPEC_CFG_I_TX_WORDMODE0_SET(dst, src) \ > + (((dst) & ~0x00070000) | (((u32) (src) << 16) & 0x00070000)) > +#define REGSPEC_CFG_I_RX_WORDMODE0_SET(dst, src) \ > + (((dst) & ~0x00e00000) | (((u32) (src) << 21) & 0x00e00000)) > +#define SATA_ENET_SDS_CTL0 0x0000000c > +#define REGSPEC_CFG_I_CUSTOMER_PIN_MODE0_SET(dst, src) \ > + (((dst) & ~0x00007fff) | (((u32) (src)) & 0x00007fff)) > +#define SATA_ENET_SDS_CTL1 0x00000010 > +#define CFG_I_SPD_SEL_CDR_OVR1_SET(dst, src) \ > + (((dst) & ~0x0000000f) | (((u32) (src)) & 0x0000000f)) > +#define SATA_ENET_SDS_RST_CTL 0x00000024 > +#define SATA_ENET_SDS_IND_CMD_REG 0x0000003c > +#define CFG_IND_WR_CMD_MASK 0x00000001 > +#define CFG_IND_RD_CMD_MASK 0x00000002 > +#define CFG_IND_CMD_DONE_MASK 0x00000004 > +#define CFG_IND_ADDR_SET(dst, src) \ > + (((dst) & ~0x003ffff0) | (((u32) (src) << 4) & 0x003ffff0)) > +#define SATA_ENET_SDS_IND_RDATA_REG 0x00000040 > +#define SATA_ENET_SDS_IND_WDATA_REG 0x00000044 > +#define SATA_ENET_CLK_MACRO_REG 0x0000004c > +#define I_RESET_B_SET(dst, src) \ > + (((dst) & ~0x00000001) | (((u32) (src)) & 0x00000001)) > +#define I_PLL_FBDIV_SET(dst, src) \ > + (((dst) & ~0x001ff000) | (((u32) (src) << 12) & 0x001ff000)) > +#define I_CUSTOMEROV_SET(dst, src) \ > + (((dst) & ~0x00000f80) | (((u32) (src) << 7) & 0x00000f80)) > +#define O_PLL_LOCK_RD(src) (((src) & 0x40000000) >> 30) > +#define O_PLL_READY_RD(src) (((src) & 0x80000000) >> 31) > + > +/* PLL Clock Macro Unit (CMU) CSR accessing from SDS indirectly */ > +#define CMU_REG0 0x00000 > +#define CMU_REG0_PLL_REF_SEL_MASK 0x00002000 > +#define CMU_REG0_PLL_REF_SEL_SET(dst, src) \ > + (((dst) & ~0x00002000) | (((u32) (src) << 13) & 0x00002000)) > +#define CMU_REG0_PDOWN_MASK 0x00004000 > +#define CMU_REG0_CAL_COUNT_RESOL_SET(dst, src) \ > + (((dst) & ~0x000000e0) | (((u32) (src) << 5) & 0x000000e0)) > +#define CMU_REG1 0x00002 > +#define CMU_REG1_PLL_CP_SET(dst, src) \ > + (((dst) & ~0x00003c00) | (((u32) (src) << 10) & 0x00003c00)) > +#define CMU_REG1_PLL_MANUALCAL_SET(dst, src) \ > + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008)) > +#define CMU_REG1_PLL_CP_SEL_SET(dst, src) \ > + (((dst) & ~0x000003e0) | (((u32) (src) << 5) & 0x000003e0)) > +#define CMU_REG1_REFCLK_CMOS_SEL_MASK 0x00000001 > +#define CMU_REG1_REFCLK_CMOS_SEL_SET(dst, src) \ > + (((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001)) > +#define CMU_REG2 0x00004 > +#define CMU_REG2_PLL_REFDIV_SET(dst, src) \ > + (((dst) & ~0x0000c000) | (((u32) (src) << 14) & 0x0000c000)) > +#define CMU_REG2_PLL_LFRES_SET(dst, src) \ > + (((dst) & ~0x0000001e) | (((u32) (src) << 1) & 0x0000001e)) > +#define CMU_REG2_PLL_FBDIV_SET(dst, src) \ > + (((dst) & ~0x00003fe0) | (((u32) (src) << 5) & 0x00003fe0)) > +#define CMU_REG3 0x00006 > +#define CMU_REG3_VCOVARSEL_SET(dst, src) \ > + (((dst) & ~0x0000000f) | (((u32) (src) << 0) & 0x0000000f)) > +#define CMU_REG3_VCO_MOMSEL_INIT_SET(dst, src) \ > + (((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0)) > +#define CMU_REG3_VCO_MANMOMSEL_SET(dst, src) \ > + (((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00)) > +#define CMU_REG4 0x00008 > +#define CMU_REG5 0x0000a > +#define CMU_REG5_PLL_LFSMCAP_SET(dst, src) \ > + (((dst) & ~0x0000c000) | (((u32) (src) << 14) & 0x0000c000)) > +#define CMU_REG5_PLL_LOCK_RESOLUTION_SET(dst, src) \ > + (((dst) & ~0x0000000e) | (((u32) (src) << 1) & 0x0000000e)) > +#define CMU_REG5_PLL_LFCAP_SET(dst, src) \ > + (((dst) & ~0x00003000) | (((u32) (src) << 12) & 0x00003000)) > +#define CMU_REG5_PLL_RESETB_MASK 0x00000001 > +#define CMU_REG6 0x0000c > +#define CMU_REG6_PLL_VREGTRIM_SET(dst, src) \ > + (((dst) & ~0x00000600) | (((u32) (src) << 9) & 0x00000600)) > +#define CMU_REG6_MAN_PVT_CAL_SET(dst, src) \ > + (((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004)) > +#define CMU_REG7 0x0000e > +#define CMU_REG7_PLL_CALIB_DONE_RD(src) ((0x00004000 & (u32) (src)) >> 14) > +#define CMU_REG7_VCO_CAL_FAIL_RD(src) ((0x00000c00 & (u32) (src)) >> 10) > +#define CMU_REG8 0x00010 > +#define CMU_REG9 0x00012 > +#define CMU_REG9_WORD_LEN_8BIT 0x000 > +#define CMU_REG9_WORD_LEN_10BIT 0x001 > +#define CMU_REG9_WORD_LEN_16BIT 0x002 > +#define CMU_REG9_WORD_LEN_20BIT 0x003 > +#define CMU_REG9_WORD_LEN_32BIT 0x004 > +#define CMU_REG9_WORD_LEN_40BIT 0x005 > +#define CMU_REG9_WORD_LEN_64BIT 0x006 > +#define CMU_REG9_WORD_LEN_66BIT 0x007 > +#define CMU_REG9_TX_WORD_MODE_CH1_SET(dst, src) \ > + (((dst) & ~0x00000380) | (((u32) (src) << 7) & 0x00000380)) > +#define CMU_REG9_TX_WORD_MODE_CH0_SET(dst, src) \ > + (((dst) & ~0x00000070) | (((u32) (src) << 4) & 0x00000070)) > +#define CMU_REG9_PLL_POST_DIVBY2_SET(dst, src) \ > + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008)) > +#define CMU_REG9_VBG_BYPASSB_SET(dst, src) \ > + (((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004)) > +#define CMU_REG9_IGEN_BYPASS_SET(dst, src) \ > + (((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002)) > +#define CMU_REG10 0x00014 > +#define CMU_REG10_VREG_REFSEL_SET(dst, src) \ > + (((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001)) > +#define CMU_REG11 0x00016 > +#define CMU_REG12 0x00018 > +#define CMU_REG12_STATE_DELAY9_SET(dst, src) \ > + (((dst) & ~0x000000f0) | (((u32) (src) << 4) & 0x000000f0)) > +#define CMU_REG13 0x0001a > +#define CMU_REG14 0x0001c > +#define CMU_REG15 0x0001e > +#define CMU_REG16 0x00020 > +#define CMU_REG16_PVT_DN_MAN_ENA_MASK 0x00000001 > +#define CMU_REG16_PVT_UP_MAN_ENA_MASK 0x00000002 > +#define CMU_REG16_VCOCAL_WAIT_BTW_CODE_SET(dst, src) \ > + (((dst) & ~0x0000001c) | (((u32) (src) << 2) & 0x0000001c)) > +#define CMU_REG16_CALIBRATION_DONE_OVERRIDE_SET(dst, src) \ > + (((dst) & ~0x00000040) | (((u32) (src) << 6) & 0x00000040)) > +#define CMU_REG16_BYPASS_PLL_LOCK_SET(dst, src) \ > + (((dst) & ~0x00000020) | (((u32) (src) << 5) & 0x00000020)) > +#define CMU_REG17 0x00022 > +#define CMU_REG17_PVT_CODE_R2A_SET(dst, src) \ > + (((dst) & ~0x00007f00) | (((u32) (src) << 8) & 0x00007f00)) > +#define CMU_REG17_RESERVED_7_SET(dst, src) \ > + (((dst) & ~0x000000e0) | (((u32) (src) << 5) & 0x000000e0)) > +#define CMU_REG17_PVT_TERM_MAN_ENA_MASK 0x00008000 > +#define CMU_REG18 0x00024 > +#define CMU_REG19 0x00026 > +#define CMU_REG20 0x00028 > +#define CMU_REG21 0x0002a > +#define CMU_REG22 0x0002c > +#define CMU_REG23 0x0002e > +#define CMU_REG24 0x00030 > +#define CMU_REG25 0x00032 > +#define CMU_REG26 0x00034 > +#define CMU_REG26_FORCE_PLL_LOCK_SET(dst, src) \ > + (((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001)) > +#define CMU_REG27 0x00036 > +#define CMU_REG28 0x00038 > +#define CMU_REG29 0x0003a > +#define CMU_REG30 0x0003c > +#define CMU_REG30_LOCK_COUNT_SET(dst, src) \ > + (((dst) & ~0x00000006) | (((u32) (src) << 1) & 0x00000006)) > +#define CMU_REG30_PCIE_MODE_SET(dst, src) \ > + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008)) > +#define CMU_REG31 0x0003e > +#define CMU_REG32 0x00040 > +#define CMU_REG32_FORCE_VCOCAL_START_MASK 0x00004000 > +#define CMU_REG32_PVT_CAL_WAIT_SEL_SET(dst, src) \ > + (((dst) & ~0x00000006) | (((u32) (src) << 1) & 0x00000006)) > +#define CMU_REG32_IREF_ADJ_SET(dst, src) \ > + (((dst) & ~0x00000180) | (((u32) (src) << 7) & 0x00000180)) > +#define CMU_REG33 0x00042 > +#define CMU_REG34 0x00044 > +#define CMU_REG34_VCO_CAL_VTH_LO_MAX_SET(dst, src) \ > + (((dst) & ~0x0000000f) | (((u32) (src) << 0) & 0x0000000f)) > +#define CMU_REG34_VCO_CAL_VTH_HI_MAX_SET(dst, src) \ > + (((dst) & ~0x00000f00) | (((u32) (src) << 8) & 0x00000f00)) > +#define CMU_REG34_VCO_CAL_VTH_LO_MIN_SET(dst, src) \ > + (((dst) & ~0x000000f0) | (((u32) (src) << 4) & 0x000000f0)) > +#define CMU_REG34_VCO_CAL_VTH_HI_MIN_SET(dst, src) \ > + (((dst) & ~0x0000f000) | (((u32) (src) << 12) & 0x0000f000)) > +#define CMU_REG35 0x00046 > +#define CMU_REG35_PLL_SSC_MOD_SET(dst, src) \ > + (((dst) & ~0x0000fe00) | (((u32) (src) << 9) & 0x0000fe00)) > +#define CMU_REG36 0x00048 > +#define CMU_REG36_PLL_SSC_EN_SET(dst, src) \ > + (((dst) & ~0x00000010) | (((u32) (src) << 4) & 0x00000010)) > +#define CMU_REG36_PLL_SSC_VSTEP_SET(dst, src) \ > + (((dst) & ~0x0000ffc0) | (((u32) (src) << 6) & 0x0000ffc0)) > +#define CMU_REG36_PLL_SSC_DSMSEL_SET(dst, src) \ > + (((dst) & ~0x00000020) | (((u32) (src) << 5) & 0x00000020)) > +#define CMU_REG37 0x0004a > +#define CMU_REG38 0x0004c > +#define CMU_REG39 0x0004e > + > +/* PHY lane CSR accessing from SDS indirectly */ > +#define RXTX_REG0 0x000 > +#define RXTX_REG0_CTLE_EQ_HR_SET(dst, src) \ > + (((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800)) > +#define RXTX_REG0_CTLE_EQ_QR_SET(dst, src) \ > + (((dst) & ~0x000007c0) | (((u32) (src) << 6) & 0x000007c0)) > +#define RXTX_REG0_CTLE_EQ_FR_SET(dst, src) \ > + (((dst) & ~0x0000003e) | (((u32) (src) << 1) & 0x0000003e)) > +#define RXTX_REG1 0x002 > +#define RXTX_REG1_RXACVCM_SET(dst, src) \ > + (((dst) & ~0x0000f000) | (((u32) (src) << 12) & 0x0000f000)) > +#define RXTX_REG1_CTLE_EQ_SET(dst, src) \ > + (((dst) & ~0x00000f80) | (((u32) (src) << 7) & 0x00000f80)) > +#define RXTX_REG1_RXVREG1_SET(dst, src) \ > + (((dst) & ~0x00000060) | (((u32) (src) << 5) & 0x00000060)) > +#define RXTX_REG1_RXIREF_ADJ_SET(dst, src) \ > + (((dst) & ~0x00000006) | (((u32) (src) << 1) & 0x00000006)) > +#define RXTX_REG2 0x004 > +#define RXTX_REG2_VTT_ENA_SET(dst, src) \ > + (((dst) & ~0x00000100) | (((u32) (src) << 8) & 0x00000100)) > +#define RXTX_REG2_TX_FIFO_ENA_SET(dst, src) \ > + (((dst) & ~0x00000020) | (((u32) (src) << 5) & 0x00000020)) > +#define RXTX_REG2_VTT_SEL_SET(dst, src) \ > + (((dst) & ~0x000000c0) | (((u32) (src) << 6) & 0x000000c0)) > +#define RXTX_REG4 0x008 > +#define RXTX_REG4_TX_LOOPBACK_BUF_EN_MASK 0x00000040 > +#define RXTX_REG4_TX_DATA_RATE_SET(dst, src) \ > + (((dst) & ~0x0000c000) | (((u32) (src) << 14) & 0x0000c000)) > +#define RXTX_REG4_TX_WORD_MODE_SET(dst, src) \ > + (((dst) & ~0x00003800) | (((u32) (src) << 11) & 0x00003800)) > +#define RXTX_REG5 0x00a > +#define RXTX_REG5_TX_CN1_SET(dst, src) \ > + (((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800)) > +#define RXTX_REG5_TX_CP1_SET(dst, src) \ > + (((dst) & ~0x000007e0) | (((u32) (src) << 5) & 0x000007e0)) > +#define RXTX_REG5_TX_CN2_SET(dst, src) \ > + (((dst) & ~0x0000001f) | (((u32) (src) << 0) & 0x0000001f)) > +#define RXTX_REG6 0x00c > +#define RXTX_REG6_TXAMP_CNTL_SET(dst, src) \ > + (((dst) & ~0x00000780) | (((u32) (src) << 7) & 0x00000780)) > +#define RXTX_REG6_TXAMP_ENA_SET(dst, src) \ > + (((dst) & ~0x00000040) | (((u32) (src) << 6) & 0x00000040)) > +#define RXTX_REG6_RX_BIST_ERRCNT_RD_SET(dst, src) \ > + (((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001)) > +#define RXTX_REG6_TX_IDLE_SET(dst, src) \ > + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008)) > +#define RXTX_REG6_RX_BIST_RESYNC_SET(dst, src) \ > + (((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002)) > +#define RXTX_REG7 0x00e > +#define RXTX_REG7_RESETB_RXD_MASK 0x00000100 > +#define RXTX_REG7_RESETB_RXA_MASK 0x00000080 > +#define RXTX_REG7_BIST_ENA_RX_SET(dst, src) \ > + (((dst) & ~0x00000040) | (((u32) (src) << 6) & 0x00000040)) > +#define RXTX_REG7_RX_WORD_MODE_SET(dst, src) \ > + (((dst) & ~0x00003800) | (((u32) (src) << 11) & 0x00003800)) > +#define RXTX_REG8 0x010 > +#define RXTX_REG8_CDR_LOOP_ENA_SET(dst, src) \ > + (((dst) & ~0x00004000) | (((u32) (src) << 14) & 0x00004000)) > +#define RXTX_REG8_CDR_BYPASS_RXLOS_SET(dst, src) \ > + (((dst) & ~0x00000800) | (((u32) (src) << 11) & 0x00000800)) > +#define RXTX_REG8_SSC_ENABLE_SET(dst, src) \ > + (((dst) & ~0x00000200) | (((u32) (src) << 9) & 0x00000200)) > +#define RXTX_REG8_SD_VREF_SET(dst, src) \ > + (((dst) & ~0x000000f0) | (((u32) (src) << 4) & 0x000000f0)) > +#define RXTX_REG8_SD_DISABLE_SET(dst, src) \ > + (((dst) & ~0x00000100) | (((u32) (src) << 8) & 0x00000100)) > +#define RXTX_REG7 0x00e > +#define RXTX_REG7_RESETB_RXD_SET(dst, src) \ > + (((dst) & ~0x00000100) | (((u32) (src) << 8) & 0x00000100)) > +#define RXTX_REG7_RESETB_RXA_SET(dst, src) \ > + (((dst) & ~0x00000080) | (((u32) (src) << 7) & 0x00000080)) > +#define RXTX_REG7_LOOP_BACK_ENA_CTLE_MASK 0x00004000 > +#define RXTX_REG7_LOOP_BACK_ENA_CTLE_SET(dst, src) \ > + (((dst) & ~0x00004000) | (((u32) (src) << 14) & 0x00004000)) > +#define RXTX_REG11 0x016 > +#define RXTX_REG11_PHASE_ADJUST_LIMIT_SET(dst, src) \ > + (((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800)) > +#define RXTX_REG12 0x018 > +#define RXTX_REG12_LATCH_OFF_ENA_SET(dst, src) \ > + (((dst) & ~0x00002000) | (((u32) (src) << 13) & 0x00002000)) > +#define RXTX_REG12_SUMOS_ENABLE_SET(dst, src) \ > + (((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004)) > +#define RXTX_REG12_RX_DET_TERM_ENABLE_MASK 0x00000002 > +#define RXTX_REG12_RX_DET_TERM_ENABLE_SET(dst, src) \ > + (((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002)) > +#define RXTX_REG13 0x01a > +#define RXTX_REG14 0x01c > +#define RXTX_REG14_CLTE_LATCAL_MAN_PROG_SET(dst, src) \ > + (((dst) & ~0x0000003f) | (((u32) (src) << 0) & 0x0000003f)) > +#define RXTX_REG14_CTLE_LATCAL_MAN_ENA_SET(dst, src) \ > + (((dst) & ~0x00000040) | (((u32) (src) << 6) & 0x00000040)) > +#define RXTX_REG26 0x034 > +#define RXTX_REG26_PERIOD_ERROR_LATCH_SET(dst, src) \ > + (((dst) & ~0x00003800) | (((u32) (src) << 11) & 0x00003800)) > +#define RXTX_REG26_BLWC_ENA_SET(dst, src) \ > + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008)) > +#define RXTX_REG21 0x02a > +#define RXTX_REG21_DO_LATCH_CALOUT_RD(src) ((0x0000fc00 & (u32) (src)) >> 10) > +#define RXTX_REG21_XO_LATCH_CALOUT_RD(src) ((0x000003f0 & (u32) (src)) >> 4) > +#define RXTX_REG21_LATCH_CAL_FAIL_ODD_RD(src) ((0x0000000f & (u32)(src))) > +#define RXTX_REG22 0x02c > +#define RXTX_REG22_SO_LATCH_CALOUT_RD(src) ((0x000003f0 & (u32) (src)) >> 4) > +#define RXTX_REG22_EO_LATCH_CALOUT_RD(src) ((0x0000fc00 & (u32) (src)) >> 10) > +#define RXTX_REG22_LATCH_CAL_FAIL_EVEN_RD(src) ((0x0000000f & (u32)(src))) > +#define RXTX_REG23 0x02e > +#define RXTX_REG23_DE_LATCH_CALOUT_RD(src) ((0x0000fc00 & (u32) (src)) >> 10) > +#define RXTX_REG23_XE_LATCH_CALOUT_RD(src) ((0x000003f0 & (u32) (src)) >> 4) > +#define RXTX_REG24 0x030 > +#define RXTX_REG24_EE_LATCH_CALOUT_RD(src) ((0x0000fc00 & (u32) (src)) >> 10) > +#define RXTX_REG24_SE_LATCH_CALOUT_RD(src) ((0x000003f0 & (u32) (src)) >> 4) > +#define RXTX_REG27 0x036 > +#define RXTX_REG28 0x038 > +#define RXTX_REG31 0x03e > +#define RXTX_REG38 0x04c > +#define RXTX_REG38_CUSTOMER_PINMODE_INV_SET(dst, src) \ > + (((dst) & 0x0000fffe) | (((u32) (src) << 1) & 0x0000fffe)) > +#define RXTX_REG39 0x04e > +#define RXTX_REG40 0x050 > +#define RXTX_REG41 0x052 > +#define RXTX_REG42 0x054 > +#define RXTX_REG43 0x056 > +#define RXTX_REG44 0x058 > +#define RXTX_REG45 0x05a > +#define RXTX_REG46 0x05c > +#define RXTX_REG47 0x05e > +#define RXTX_REG48 0x060 > +#define RXTX_REG49 0x062 > +#define RXTX_REG50 0x064 > +#define RXTX_REG51 0x066 > +#define RXTX_REG52 0x068 > +#define RXTX_REG53 0x06a > +#define RXTX_REG54 0x06c > +#define RXTX_REG55 0x06e > +#define RXTX_REG61 0x07a > +#define RXTX_REG61_ISCAN_INBERT_SET(dst, src) \ > + (((dst) & ~0x00000010) | (((u32) (src) << 4) & 0x00000010)) > +#define RXTX_REG61_LOADFREQ_SHIFT_SET(dst, src) \ > + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008)) > +#define RXTX_REG61_EYE_COUNT_WIDTH_SEL_SET(dst, src) \ > + (((dst) & ~0x000000c0) | (((u32) (src) << 6) & 0x000000c0)) > +#define RXTX_REG61_SPD_SEL_CDR_SET(dst, src) \ > + (((dst) & ~0x00003c00) | (((u32) (src) << 10) & 0x00003c00)) > +#define RXTX_REG62 0x07c > +#define RXTX_REG62_PERIOD_H1_QLATCH_SET(dst, src) \ > + (((dst) & ~0x00003800) | (((u32) (src) << 11) & 0x00003800)) > +#define RXTX_REG81 0x0a2 > +#define RXTX_REG89_MU_TH7_SET(dst, src) \ > + (((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800)) > +#define RXTX_REG89_MU_TH8_SET(dst, src) \ > + (((dst) & ~0x000007c0) | (((u32) (src) << 6) & 0x000007c0)) > +#define RXTX_REG89_MU_TH9_SET(dst, src) \ > + (((dst) & ~0x0000003e) | (((u32) (src) << 1) & 0x0000003e)) > +#define RXTX_REG96 0x0c0 > +#define RXTX_REG96_MU_FREQ1_SET(dst, src) \ > + (((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800)) > +#define RXTX_REG96_MU_FREQ2_SET(dst, src) \ > + (((dst) & ~0x000007c0) | (((u32) (src) << 6) & 0x000007c0)) > +#define RXTX_REG96_MU_FREQ3_SET(dst, src) \ > + (((dst) & ~0x0000003e) | (((u32) (src) << 1) & 0x0000003e)) > +#define RXTX_REG99 0x0c6 > +#define RXTX_REG99_MU_PHASE1_SET(dst, src) \ > + (((dst) & ~0x0000f800) | (((u32) (src) << 11) & 0x0000f800)) > +#define RXTX_REG99_MU_PHASE2_SET(dst, src) \ > + (((dst) & ~0x000007c0) | (((u32) (src) << 6) & 0x000007c0)) > +#define RXTX_REG99_MU_PHASE3_SET(dst, src) \ > + (((dst) & ~0x0000003e) | (((u32) (src) << 1) & 0x0000003e)) > +#define RXTX_REG102 0x0cc > +#define RXTX_REG102_FREQLOOP_LIMIT_SET(dst, src) \ > + (((dst) & ~0x00000060) | (((u32) (src) << 5) & 0x00000060)) > +#define RXTX_REG114 0x0e4 > +#define RXTX_REG121 0x0f2 > +#define RXTX_REG121_SUMOS_CAL_CODE_RD(src) ((0x0000003e & (u32)(src)) >> 0x1) > +#define RXTX_REG125 0x0fa > +#define RXTX_REG125_PQ_REG_SET(dst, src) \ > + (((dst) & ~0x0000fe00) | (((u32) (src) << 9) & 0x0000fe00)) > +#define RXTX_REG125_SIGN_PQ_SET(dst, src) \ > + (((dst) & ~0x00000100) | (((u32) (src) << 8) & 0x00000100)) > +#define RXTX_REG125_SIGN_PQ_2C_SET(dst, src) \ > + (((dst) & ~0x00000080) | (((u32) (src) << 7) & 0x00000080)) > +#define RXTX_REG125_PHZ_MANUALCODE_SET(dst, src) \ > + (((dst) & ~0x0000007c) | (((u32) (src) << 2) & 0x0000007c)) > +#define RXTX_REG125_PHZ_MANUAL_SET(dst, src) \ > + (((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002)) > +#define RXTX_REG127 0x0fe > +#define RXTX_REG127_FORCE_SUM_CAL_START_MASK 0x00000002 > +#define RXTX_REG127_FORCE_LAT_CAL_START_MASK 0x00000004 > +#define RXTX_REG127_FORCE_SUM_CAL_START_SET(dst, src) \ > + (((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002)) > +#define RXTX_REG127_FORCE_LAT_CAL_START_SET(dst, src) \ > + (((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004)) > +#define RXTX_REG127_LATCH_MAN_CAL_ENA_SET(dst, src) \ > + (((dst) & ~0x00000008) | (((u32) (src) << 3) & 0x00000008)) > +#define RXTX_REG127_DO_LATCH_MANCAL_SET(dst, src) \ > + (((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00)) > +#define RXTX_REG127_XO_LATCH_MANCAL_SET(dst, src) \ > + (((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0)) > +#define RXTX_REG128 0x100 > +#define RXTX_REG128_LATCH_CAL_WAIT_SEL_SET(dst, src) \ > + (((dst) & ~0x0000000c) | (((u32) (src) << 2) & 0x0000000c)) > +#define RXTX_REG128_EO_LATCH_MANCAL_SET(dst, src) \ > + (((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00)) > +#define RXTX_REG128_SO_LATCH_MANCAL_SET(dst, src) \ > + (((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0)) > +#define RXTX_REG129 0x102 > +#define RXTX_REG129_DE_LATCH_MANCAL_SET(dst, src) \ > + (((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00)) > +#define RXTX_REG129_XE_LATCH_MANCAL_SET(dst, src) \ > + (((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0)) > +#define RXTX_REG130 0x104 > +#define RXTX_REG130_EE_LATCH_MANCAL_SET(dst, src) \ > + (((dst) & ~0x0000fc00) | (((u32) (src) << 10) & 0x0000fc00)) > +#define RXTX_REG130_SE_LATCH_MANCAL_SET(dst, src) \ > + (((dst) & ~0x000003f0) | (((u32) (src) << 4) & 0x000003f0)) > +#define RXTX_REG145 0x122 > +#define RXTX_REG145_TX_IDLE_SATA_SET(dst, src) \ > + (((dst) & ~0x00000001) | (((u32) (src) << 0) & 0x00000001)) > +#define RXTX_REG145_RXES_ENA_SET(dst, src) \ > + (((dst) & ~0x00000002) | (((u32) (src) << 1) & 0x00000002)) > +#define RXTX_REG145_RXDFE_CONFIG_SET(dst, src) \ > + (((dst) & ~0x0000c000) | (((u32) (src) << 14) & 0x0000c000)) > +#define RXTX_REG145_RXVWES_LATENA_SET(dst, src) \ > + (((dst) & ~0x00000004) | (((u32) (src) << 2) & 0x00000004)) > +#define RXTX_REG147 0x126 > +#define RXTX_REG148 0x128 > + > +/* Clock macro type */ > +enum cmu_type_t { > + REF_CMU = 0, /* Clock macro is the internal reference clock */ > + PHY_CMU = 1, /* Clock macro is the PLL for the Serdes */ > +}; > + > +enum mux_type_t { > + MUX_SELECT_ATA = 0, /* Switch the MUX to ATA */ > + MUX_SELECT_SGMMII = 0, /* Switch the MUX to SGMII */ > +}; > + > +enum clk_type_t { > + CLK_EXT_DIFF = 0, /* External differential */ > + CLK_INT_DIFF = 1, /* Internal differential */ > + CLK_INT_SING = 2, /* Internal single ended */ > +}; > + > +enum phy_mode { > + MODE_SATA = 0, /* List them for simple reference */ > + MODE_SGMII = 1, > + MODE_PCIE = 2, > + MODE_USB = 3, > + MODE_XFI = 4, > + MODE_MAX > +}; > + > +struct xgene_sata_override_param { > + u32 speed[MAX_LANE]; /* Index for override parameter per lane */ > + u32 txspeed[3]; /* Tx speed */ > + u32 txboostgain[MAX_LANE*3]; /* Tx freq boost and gain control */ > + u32 txeyetuning[MAX_LANE*3]; /* Tx eye tuning */ > + u32 txeyedirection[MAX_LANE*3]; /* Tx eye tuning direction */ > + u32 txamplitude[MAX_LANE*3]; /* Tx amplitude control */ > + u32 txprecursor_cn1[MAX_LANE*3]; /* Tx emphasis taps 1st pre-cursor */ > + u32 txprecursor_cn2[MAX_LANE*3]; /* Tx emphasis taps 2nd pre-cursor */ > + u32 txpostcursor_cp1[MAX_LANE*3]; /* Tx emphasis taps post-cursor */ > +}; > + > +struct xgene_phy_ctx { > + struct device *dev; > + struct phy *phy; > + enum phy_mode mode; /* Mode of operation */ > + enum clk_type_t clk_type; /* Input clock selection */ > + void __iomem *sds_base; /* PHY CSR base addr */ > + struct clk *clk; /* Optional clock */ > + > + /* Override Serdes parameters */ > + struct xgene_sata_override_param sata_param; > +}; > + > +/* > + * For chip earlier than A3 version, enable this flag. > + * To enable, pass boot argument phy_xgene.preA3Chip=1 > + */ > +static int preA3Chip; > +MODULE_PARM_DESC(preA3Chip, "Enable pre-A3 chip support (1=enable 0=disable)"); > +module_param_named(preA3Chip, preA3Chip, int, 0444); > + > +static void sds_wr(void __iomem *csr_base, u32 indirect_cmd_reg, > + u32 indirect_data_reg, u32 addr, u32 data) > +{ > + unsigned long deadline = jiffies + HZ; > + u32 val; > + u32 cmd; > + > + cmd = CFG_IND_WR_CMD_MASK | CFG_IND_CMD_DONE_MASK; > + cmd = CFG_IND_ADDR_SET(cmd, addr); > + writel(data, csr_base + indirect_data_reg); > + readl(csr_base + indirect_data_reg); /* Force a barrier */ > + writel(cmd, csr_base + indirect_cmd_reg); > + readl(csr_base + indirect_cmd_reg); /* Force a barrier */ > + do { > + val = readl(csr_base + indirect_cmd_reg); > + } while (!(val & CFG_IND_CMD_DONE_MASK) && > + time_before(jiffies, deadline)); > + if (!(val & CFG_IND_CMD_DONE_MASK)) > + pr_err("SDS WR timeout at 0x%p offset 0x%08X value 0x%08X\n", > + csr_base + indirect_cmd_reg, addr, data); > +} > + > +static void sds_rd(void __iomem *csr_base, u32 indirect_cmd_reg, > + u32 indirect_data_reg, u32 addr, u32 *data) > +{ > + unsigned long deadline = jiffies + HZ; > + u32 val; > + u32 cmd; > + > + cmd = CFG_IND_RD_CMD_MASK | CFG_IND_CMD_DONE_MASK; > + cmd = CFG_IND_ADDR_SET(cmd, addr); > + writel(cmd, csr_base + indirect_cmd_reg); > + readl(csr_base + indirect_cmd_reg); /* Force a barrier */ > + do { > + val = readl(csr_base + indirect_cmd_reg); > + } while (!(val & CFG_IND_CMD_DONE_MASK) && > + time_before(jiffies, deadline)); > + *data = readl(csr_base + indirect_data_reg); > + if (!(val & CFG_IND_CMD_DONE_MASK)) > + pr_err("SDS WR timeout at 0x%p offset 0x%08X value 0x%08X\n", > + csr_base + indirect_cmd_reg, addr, *data); > +} > + > +static void cmu_wr(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type, > + u32 reg, u32 data) > +{ > + void __iomem *sds_base = ctx->sds_base; > + u32 val; > + > + if (cmu_type == REF_CMU) > + reg += SERDES_PLL_REF_INDIRECT_OFFSET; > + else > + reg += SERDES_PLL_INDIRECT_OFFSET; > + sds_wr(sds_base, SATA_ENET_SDS_IND_CMD_REG, > + SATA_ENET_SDS_IND_WDATA_REG, reg, data); > + sds_rd(sds_base, SATA_ENET_SDS_IND_CMD_REG, > + SATA_ENET_SDS_IND_RDATA_REG, reg, &val); > + pr_debug("CMU WR addr 0x%X value 0x%08X <-> 0x%08X\n", reg, data, val); > +} > + > +static void cmu_rd(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type, > + u32 reg, u32 *data) > +{ > + void __iomem *sds_base = ctx->sds_base; > + > + if (cmu_type == REF_CMU) > + reg += SERDES_PLL_REF_INDIRECT_OFFSET; > + else > + reg += SERDES_PLL_INDIRECT_OFFSET; > + sds_rd(sds_base, SATA_ENET_SDS_IND_CMD_REG, > + SATA_ENET_SDS_IND_RDATA_REG, reg, data); > + pr_debug("CMU RD addr 0x%X value 0x%08X\n", reg, *data); > +} > + > +static void cmu_toggle1to0(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type, > + u32 reg, u32 bits) > +{ > + u32 val; > + > + cmu_rd(ctx, cmu_type, reg, &val); > + val |= bits; > + cmu_wr(ctx, cmu_type, reg, val); > + cmu_rd(ctx, cmu_type, reg, &val); > + val &= ~bits; > + cmu_wr(ctx, cmu_type, reg, val); > +} > + > +static void cmu_clrbits(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type, > + u32 reg, u32 bits) > +{ > + u32 val; > + > + cmu_rd(ctx, cmu_type, reg, &val); > + val &= ~bits; > + cmu_wr(ctx, cmu_type, reg, val); > +} > + > +static void cmu_setbits(struct xgene_phy_ctx *ctx, enum cmu_type_t cmu_type, > + u32 reg, u32 bits) > +{ > + u32 val; > + > + cmu_rd(ctx, cmu_type, reg, &val); > + val |= bits; > + cmu_wr(ctx, cmu_type, reg, val); > +} > + > +static void serdes_wr(struct xgene_phy_ctx *ctx, int lane, u32 reg, u32 data) > +{ > + void __iomem *sds_base = ctx->sds_base; > + u32 val; > + > + reg += SERDES_INDIRECT_OFFSET; > + reg += lane * SERDES_LANE_STRIDE; > + sds_wr(sds_base, SATA_ENET_SDS_IND_CMD_REG, > + SATA_ENET_SDS_IND_WDATA_REG, reg, data); > + sds_rd(sds_base, SATA_ENET_SDS_IND_CMD_REG, > + SATA_ENET_SDS_IND_RDATA_REG, reg, &val); > + pr_debug("SERDES WR addr 0x%X value 0x%08X <-> 0x%08X\n", reg, data, > + val); > +} > + > +static void serdes_rd(struct xgene_phy_ctx *ctx, int lane, u32 reg, u32 *data) > +{ > + void __iomem *sds_base = ctx->sds_base; > + > + reg += SERDES_INDIRECT_OFFSET; > + reg += lane * SERDES_LANE_STRIDE; > + sds_rd(sds_base, SATA_ENET_SDS_IND_CMD_REG, > + SATA_ENET_SDS_IND_RDATA_REG, reg, data); > + pr_debug("SERDES RD addr 0x%X value 0x%08X\n", reg, *data); > +} > + > +static void serdes_clrbits(struct xgene_phy_ctx *ctx, int lane, u32 reg, > + u32 bits) > +{ > + u32 val; > + > + serdes_rd(ctx, lane, reg, &val); > + val &= ~bits; > + serdes_wr(ctx, lane, reg, val); > +} > + > +static void serdes_setbits(struct xgene_phy_ctx *ctx, int lane, u32 reg, > + u32 bits) > +{ > + u32 val; > + > + serdes_rd(ctx, lane, reg, &val); > + val |= bits; > + serdes_wr(ctx, lane, reg, val); > +} > + > +static void xgene_phy_cfg_cmu_clk_type(struct xgene_phy_ctx *ctx, > + enum cmu_type_t cmu_type, > + enum clk_type_t clk_type) > +{ > + u32 val; > + > + /* Set the reset sequence delay for TX ready assertion */ > + cmu_rd(ctx, cmu_type, CMU_REG12, &val); > + val = CMU_REG12_STATE_DELAY9_SET(val, 0x1); > + cmu_wr(ctx, cmu_type, CMU_REG12, val); > + /* Set the programmable stage delays between various enable stages */ > + cmu_wr(ctx, cmu_type, CMU_REG13, 0x0222); > + cmu_wr(ctx, cmu_type, CMU_REG14, 0x2225); > + > + /* Configure clock type */ > + if (clk_type == CLK_EXT_DIFF) { > + /* Select external clock mux */ > + cmu_rd(ctx, cmu_type, CMU_REG0, &val); > + val = CMU_REG0_PLL_REF_SEL_SET(val, 0x0); > + cmu_wr(ctx, cmu_type, CMU_REG0, val); > + /* Select CMOS as reference clock */ > + cmu_rd(ctx, cmu_type, CMU_REG1, &val); > + val = CMU_REG1_REFCLK_CMOS_SEL_SET(val, 0x0); > + cmu_wr(ctx, cmu_type, CMU_REG1, val); > + dev_dbg(ctx->dev, "Set external reference clock\n"); > + } else if (clk_type == CLK_INT_DIFF) { > + /* Select internal clock mux */ > + cmu_rd(ctx, cmu_type, CMU_REG0, &val); > + val = CMU_REG0_PLL_REF_SEL_SET(val, 0x1); > + cmu_wr(ctx, cmu_type, CMU_REG0, val); > + /* Select CMOS as reference clock */ > + cmu_rd(ctx, cmu_type, CMU_REG1, &val); > + val = CMU_REG1_REFCLK_CMOS_SEL_SET(val, 0x1); > + cmu_wr(ctx, cmu_type, CMU_REG1, val); > + dev_dbg(ctx->dev, "Set internal reference clock\n"); > + } else if (clk_type == CLK_INT_SING) { > + /* > + * NOTE: This clock type is NOT support for controller > + * whose internal clock shared in the PCIe controller > + * > + * Select internal clock mux > + */ > + cmu_rd(ctx, cmu_type, CMU_REG1, &val); > + val = CMU_REG1_REFCLK_CMOS_SEL_SET(val, 0x1); > + cmu_wr(ctx, cmu_type, CMU_REG1, val); > + /* Select CML as reference clock */ > + cmu_rd(ctx, cmu_type, CMU_REG1, &val); > + val = CMU_REG1_REFCLK_CMOS_SEL_SET(val, 0x0); > + cmu_wr(ctx, cmu_type, CMU_REG1, val); > + dev_dbg(ctx->dev, > + "Set internal single ended reference clock\n"); > + } > +} > + > +static void xgene_phy_sata_cfg_cmu_core(struct xgene_phy_ctx *ctx, > + enum cmu_type_t cmu_type, > + enum clk_type_t clk_type) > +{ > + u32 val; > + int ref_100MHz; > + > + if (cmu_type == REF_CMU) { > + /* Set VCO calibration voltage threshold */ > + cmu_rd(ctx, cmu_type, CMU_REG34, &val); > + val = CMU_REG34_VCO_CAL_VTH_LO_MAX_SET(val, 0x7); > + val = CMU_REG34_VCO_CAL_VTH_HI_MAX_SET(val, 0xc); > + val = CMU_REG34_VCO_CAL_VTH_LO_MIN_SET(val, 0x3); > + val = CMU_REG34_VCO_CAL_VTH_HI_MIN_SET(val, 0x8); > + cmu_wr(ctx, cmu_type, CMU_REG34, val); > + } > + > + /* Set the VCO calibration counter */ > + cmu_rd(ctx, cmu_type, CMU_REG0, &val); > + if (cmu_type == REF_CMU || preA3Chip) > + val = CMU_REG0_CAL_COUNT_RESOL_SET(val, 0x4); > + else > + val = CMU_REG0_CAL_COUNT_RESOL_SET(val, 0x7); > + cmu_wr(ctx, cmu_type, CMU_REG0, val); > + > + /* Configure PLL for calibration */ > + cmu_rd(ctx, cmu_type, CMU_REG1, &val); > + val = CMU_REG1_PLL_CP_SET(val, 0x1); > + if (cmu_type == REF_CMU || preA3Chip) > + val = CMU_REG1_PLL_CP_SEL_SET(val, 0x5); > + else > + val = CMU_REG1_PLL_CP_SEL_SET(val, 0x3); > + if (cmu_type == REF_CMU) > + val = CMU_REG1_PLL_MANUALCAL_SET(val, 0x0); > + else > + val = CMU_REG1_PLL_MANUALCAL_SET(val, 0x1); > + cmu_wr(ctx, cmu_type, CMU_REG1, val); > + > + if (cmu_type != REF_CMU) > + cmu_clrbits(ctx, cmu_type, CMU_REG5, CMU_REG5_PLL_RESETB_MASK); > + > + /* Configure the PLL for either 100MHz or 50MHz */ > + cmu_rd(ctx, cmu_type, CMU_REG2, &val); > + if (cmu_type == REF_CMU) { > + val = CMU_REG2_PLL_LFRES_SET(val, 0xa); > + ref_100MHz = 1; > + } else { > + val = CMU_REG2_PLL_LFRES_SET(val, 0x3); > + if (clk_type == CLK_EXT_DIFF) > + ref_100MHz = 0; > + else > + ref_100MHz = 1; > + } > + if (ref_100MHz) { > + val = CMU_REG2_PLL_FBDIV_SET(val, FBDIV_VAL_100M); > + val = CMU_REG2_PLL_REFDIV_SET(val, REFDIV_VAL_100M); > + } else { > + val = CMU_REG2_PLL_FBDIV_SET(val, FBDIV_VAL_50M); > + val = CMU_REG2_PLL_REFDIV_SET(val, REFDIV_VAL_50M); > + } > + cmu_wr(ctx, cmu_type, CMU_REG2, val); > + > + /* Configure the VCO */ > + cmu_rd(ctx, cmu_type, CMU_REG3, &val); > + if (cmu_type == REF_CMU) { > + val = CMU_REG3_VCOVARSEL_SET(val, 0x3); > + val = CMU_REG3_VCO_MOMSEL_INIT_SET(val, 0x10); > + } else { > + val = CMU_REG3_VCOVARSEL_SET(val, 0xF); > + if (preA3Chip) > + val = CMU_REG3_VCO_MOMSEL_INIT_SET(val, 0x15); > + else > + val = CMU_REG3_VCO_MOMSEL_INIT_SET(val, 0x1a); > + val = CMU_REG3_VCO_MANMOMSEL_SET(val, 0x15); > + } > + cmu_wr(ctx, cmu_type, CMU_REG3, val); > + > + /* Disable force PLL lock */ > + cmu_rd(ctx, cmu_type, CMU_REG26, &val); > + val = CMU_REG26_FORCE_PLL_LOCK_SET(val, 0x0); > + cmu_wr(ctx, cmu_type, CMU_REG26, val); > + > + /* Setup PLL loop filter */ > + cmu_rd(ctx, cmu_type, CMU_REG5, &val); > + val = CMU_REG5_PLL_LFSMCAP_SET(val, 0x3); > + val = CMU_REG5_PLL_LFCAP_SET(val, 0x3); > + if (cmu_type == REF_CMU || !preA3Chip) > + val = CMU_REG5_PLL_LOCK_RESOLUTION_SET(val, 0x7); > + else > + val = CMU_REG5_PLL_LOCK_RESOLUTION_SET(val, 0x4); > + cmu_wr(ctx, cmu_type, CMU_REG5, val); > + > + /* Enable or disable manual calibration */ > + cmu_rd(ctx, cmu_type, CMU_REG6, &val); > + val = CMU_REG6_PLL_VREGTRIM_SET(val, preA3Chip ? 0x0 : 0x2); > + val = CMU_REG6_MAN_PVT_CAL_SET(val, preA3Chip ? 0x1 : 0x0); > + cmu_wr(ctx, cmu_type, CMU_REG6, val); > + > + /* Configure lane for 20-bits */ > + if (cmu_type == PHY_CMU) { > + cmu_rd(ctx, cmu_type, CMU_REG9, &val); > + val = CMU_REG9_TX_WORD_MODE_CH1_SET(val, > + CMU_REG9_WORD_LEN_20BIT); > + val = CMU_REG9_TX_WORD_MODE_CH0_SET(val, > + CMU_REG9_WORD_LEN_20BIT); > + val = CMU_REG9_PLL_POST_DIVBY2_SET(val, 0x1); > + if (!preA3Chip) { > + val = CMU_REG9_VBG_BYPASSB_SET(val, 0x0); > + val = CMU_REG9_IGEN_BYPASS_SET(val , 0x0); > + } > + cmu_wr(ctx, cmu_type, CMU_REG9, val); > + > + if (!preA3Chip) { > + cmu_rd(ctx, cmu_type, CMU_REG10, &val); > + val = CMU_REG10_VREG_REFSEL_SET(val, 0x1); > + cmu_wr(ctx, cmu_type, CMU_REG10, val); > + } > + } > + > + cmu_rd(ctx, cmu_type, CMU_REG16, &val); > + val = CMU_REG16_CALIBRATION_DONE_OVERRIDE_SET(val, 0x1); > + val = CMU_REG16_BYPASS_PLL_LOCK_SET(val, 0x1); > + if (cmu_type == REF_CMU || preA3Chip) > + val = CMU_REG16_VCOCAL_WAIT_BTW_CODE_SET(val, 0x4); > + else > + val = CMU_REG16_VCOCAL_WAIT_BTW_CODE_SET(val, 0x7); > + cmu_wr(ctx, cmu_type, CMU_REG16, val); > + > + /* Configure for SATA */ > + cmu_rd(ctx, cmu_type, CMU_REG30, &val); > + val = CMU_REG30_PCIE_MODE_SET(val, 0x0); > + val = CMU_REG30_LOCK_COUNT_SET(val, 0x3); > + cmu_wr(ctx, cmu_type, CMU_REG30, val); > + > + /* Disable state machine bypass */ > + cmu_wr(ctx, cmu_type, CMU_REG31, 0xF); > + > + cmu_rd(ctx, cmu_type, CMU_REG32, &val); > + val = CMU_REG32_PVT_CAL_WAIT_SEL_SET(val, 0x3); > + if (cmu_type == REF_CMU || preA3Chip) > + val = CMU_REG32_IREF_ADJ_SET(val, 0x3); > + else > + val = CMU_REG32_IREF_ADJ_SET(val, 0x1); > + cmu_wr(ctx, cmu_type, CMU_REG32, val); > + > + /* Set VCO calibration threshold */ > + if (cmu_type != REF_CMU && preA3Chip) > + cmu_wr(ctx, cmu_type, CMU_REG34, 0x8d27); > + else > + cmu_wr(ctx, cmu_type, CMU_REG34, 0x873c); > + > + /* Set CTLE Override and override waiting from state machine */ > + cmu_wr(ctx, cmu_type, CMU_REG37, 0xF00F); > +} > + > +static void xgene_phy_ssc_enable(struct xgene_phy_ctx *ctx, > + enum cmu_type_t cmu_type) > +{ > + u32 val; > + > + /* Set SSC modulation value */ > + cmu_rd(ctx, cmu_type, CMU_REG35, &val); > + val = CMU_REG35_PLL_SSC_MOD_SET(val, 98); > + cmu_wr(ctx, cmu_type, CMU_REG35, val); > + > + /* Enable SSC, set vertical step and DSM value */ > + cmu_rd(ctx, cmu_type, CMU_REG36, &val); > + val = CMU_REG36_PLL_SSC_VSTEP_SET(val, 30); > + val = CMU_REG36_PLL_SSC_EN_SET(val, 1); > + val = CMU_REG36_PLL_SSC_DSMSEL_SET(val, 1); > + cmu_wr(ctx, cmu_type, CMU_REG36, val); > + > + /* Reset the PLL */ > + cmu_clrbits(ctx, cmu_type, CMU_REG5, CMU_REG5_PLL_RESETB_MASK); > + cmu_setbits(ctx, cmu_type, CMU_REG5, CMU_REG5_PLL_RESETB_MASK); > + > + /* Force VCO calibration to restart */ > + cmu_toggle1to0(ctx, cmu_type, CMU_REG32, > + CMU_REG32_FORCE_VCOCAL_START_MASK); > +} > + > +static void xgene_phy_sata_cfg_lanes(struct xgene_phy_ctx *ctx) > +{ > + u32 val; > + u32 reg; > + int i; > + int lane; > + > + for (lane = 0; lane < MAX_LANE; lane++) { > + serdes_wr(ctx, lane, RXTX_REG147, 0x6); > + > + /* Set boost control for quarter, half, and full rate */ > + serdes_rd(ctx, lane, RXTX_REG0, &val); > + val = RXTX_REG0_CTLE_EQ_HR_SET(val, 0x10); > + val = RXTX_REG0_CTLE_EQ_QR_SET(val, 0x10); > + val = RXTX_REG0_CTLE_EQ_FR_SET(val, 0x10); > + serdes_wr(ctx, lane, RXTX_REG0, val); > + > + /* Set boost control value */ > + serdes_rd(ctx, lane, RXTX_REG1, &val); > + val = RXTX_REG1_RXACVCM_SET(val, 0x7); > + val = RXTX_REG1_CTLE_EQ_SET(val, > + ctx->sata_param.txboostgain[lane * 3 + > + ctx->sata_param.speed[lane]]); > + serdes_wr(ctx, lane, RXTX_REG1, val); > + > + /* Latch VTT value based on the termination to ground and > + enable TX FIFO */ > + serdes_rd(ctx, lane, RXTX_REG2, &val); > + val = RXTX_REG2_VTT_ENA_SET(val, 0x1); > + val = RXTX_REG2_VTT_SEL_SET(val, 0x1); > + val = RXTX_REG2_TX_FIFO_ENA_SET(val, 0x1); > + serdes_wr(ctx, lane, RXTX_REG2, val); > + > + /* Configure Tx for 20-bits */ > + serdes_rd(ctx, lane, RXTX_REG4, &val); > + val = RXTX_REG4_TX_WORD_MODE_SET(val, CMU_REG9_WORD_LEN_20BIT); > + serdes_wr(ctx, lane, RXTX_REG4, val); > + > + if (!preA3Chip) { > + serdes_rd(ctx, lane, RXTX_REG1, &val); > + val = RXTX_REG1_RXVREG1_SET(val, 0x2); > + val = RXTX_REG1_RXIREF_ADJ_SET(val, 0x2); > + serdes_wr(ctx, lane, RXTX_REG1, val); > + } > + > + /* Set pre-emphasis first 1 and 2, and post-emphasis values */ > + serdes_rd(ctx, lane, RXTX_REG5, &val); > + val = RXTX_REG5_TX_CN1_SET(val, > + ctx->sata_param.txprecursor_cn1[lane * 3 + > + ctx->sata_param.speed[lane]]); > + val = RXTX_REG5_TX_CP1_SET(val, > + ctx->sata_param.txpostcursor_cp1[lane * 3 + > + ctx->sata_param.speed[lane]]); > + val = RXTX_REG5_TX_CN2_SET(val, > + ctx->sata_param.txprecursor_cn2[lane * 3 + > + ctx->sata_param.speed[lane]]); > + serdes_wr(ctx, lane, RXTX_REG5, val); > + > + /* Set TX amplitude value */ > + serdes_rd(ctx, lane, RXTX_REG6, &val); > + val = RXTX_REG6_TXAMP_CNTL_SET(val, > + ctx->sata_param.txamplitude[lane * 3 + > + ctx->sata_param.speed[lane]]); > + val = RXTX_REG6_TXAMP_ENA_SET(val, 0x1); > + val = RXTX_REG6_TX_IDLE_SET(val, 0x0); > + val = RXTX_REG6_RX_BIST_RESYNC_SET(val, 0x0); > + val = RXTX_REG6_RX_BIST_ERRCNT_RD_SET(val, 0x0); > + serdes_wr(ctx, lane, RXTX_REG6, val); > + > + /* Configure Rx for 20-bits */ > + serdes_rd(ctx, lane, RXTX_REG7, &val); > + val = RXTX_REG7_BIST_ENA_RX_SET(val, 0x0); > + val = RXTX_REG7_RX_WORD_MODE_SET(val, CMU_REG9_WORD_LEN_20BIT); > + serdes_wr(ctx, lane, RXTX_REG7, val); > + > + /* Set CDR and LOS values and enable Rx SSC */ > + serdes_rd(ctx, lane, RXTX_REG8, &val); > + val = RXTX_REG8_CDR_LOOP_ENA_SET(val, 0x1); > + val = RXTX_REG8_CDR_BYPASS_RXLOS_SET(val, 0x0); > + val = RXTX_REG8_SSC_ENABLE_SET(val, 0x1); > + val = RXTX_REG8_SD_DISABLE_SET(val, 0x0); > + val = RXTX_REG8_SD_VREF_SET(val, 0x4); > + serdes_wr(ctx, lane, RXTX_REG8, val); > + > + /* Set phase adjust upper/lower limits */ > + serdes_rd(ctx, lane, RXTX_REG11, &val); > + val = RXTX_REG11_PHASE_ADJUST_LIMIT_SET(val, 0x0); > + serdes_wr(ctx, lane, RXTX_REG11, val); > + > + /* Enable Latch Off; disable SUMOS and Tx termination */ > + serdes_rd(ctx, lane, RXTX_REG12, &val); > + val = RXTX_REG12_LATCH_OFF_ENA_SET(val, 0x1); > + val = RXTX_REG12_SUMOS_ENABLE_SET(val, 0x0); > + val = RXTX_REG12_RX_DET_TERM_ENABLE_SET(val, 0x0); > + serdes_wr(ctx, lane, RXTX_REG12, val); > + > + /* Set period error latch to 512T and enable BWL */ > + serdes_rd(ctx, lane, RXTX_REG26, &val); > + val = RXTX_REG26_PERIOD_ERROR_LATCH_SET(val, 0x0); > + val = RXTX_REG26_BLWC_ENA_SET(val, 0x1); > + serdes_wr(ctx, lane, RXTX_REG26, val); > + > + serdes_wr(ctx, lane, RXTX_REG28, 0x0); > + > + /* Set DFE loop preset value */ > + serdes_wr(ctx, lane, RXTX_REG31, 0x0); > + > + /* Set Eye Monitor counter width to 12-bit */ > + serdes_rd(ctx, lane, RXTX_REG61, &val); > + val = RXTX_REG61_ISCAN_INBERT_SET(val, 0x1); > + val = RXTX_REG61_LOADFREQ_SHIFT_SET(val, 0x0); > + val = RXTX_REG61_EYE_COUNT_WIDTH_SEL_SET(val, 0x0); > + serdes_wr(ctx, lane, RXTX_REG61, val); > + > + serdes_rd(ctx, lane, RXTX_REG62, &val); > + val = RXTX_REG62_PERIOD_H1_QLATCH_SET(val, 0x0); > + serdes_wr(ctx, lane, RXTX_REG62, val); > + > + /* Set BW select tap X for DFE loop */ > + for (i = 0; i < 9; i++) { > + reg = RXTX_REG81 + i * 2; > + serdes_rd(ctx, lane, reg, &val); > + val = RXTX_REG89_MU_TH7_SET(val, 0xe); > + val = RXTX_REG89_MU_TH8_SET(val, 0xe); > + val = RXTX_REG89_MU_TH9_SET(val, 0xe); > + serdes_wr(ctx, lane, reg, val); > + } > + > + /* Set BW select tap X for frequency adjust loop */ > + for (i = 0; i < 3; i++) { > + reg = RXTX_REG96 + i * 2; > + serdes_rd(ctx, lane, reg, &val); > + val = RXTX_REG96_MU_FREQ1_SET(val, 0x10); > + val = RXTX_REG96_MU_FREQ2_SET(val, 0x10); > + val = RXTX_REG96_MU_FREQ3_SET(val, 0x10); > + serdes_wr(ctx, lane, reg, val); > + } > + > + /* Set BW select tap X for phase adjust loop */ > + for (i = 0; i < 3; i++) { > + reg = RXTX_REG99 + i * 2; > + serdes_rd(ctx, lane, reg, &val); > + val = RXTX_REG99_MU_PHASE1_SET(val, 0x7); > + val = RXTX_REG99_MU_PHASE2_SET(val, 0x7); > + val = RXTX_REG99_MU_PHASE3_SET(val, 0x7); > + serdes_wr(ctx, lane, reg, val); > + } > + > + serdes_rd(ctx, lane, RXTX_REG102, &val); > + val = RXTX_REG102_FREQLOOP_LIMIT_SET(val, 0x0); > + serdes_wr(ctx, lane, RXTX_REG102, val); > + > + serdes_wr(ctx, lane, RXTX_REG114, 0xffe0); > + > + serdes_rd(ctx, lane, RXTX_REG125, &val); > + val = RXTX_REG125_SIGN_PQ_SET(val, > + ctx->sata_param.txeyedirection[lane * 3 + > + ctx->sata_param.speed[lane]]); > + val = RXTX_REG125_PQ_REG_SET(val, > + ctx->sata_param.txeyetuning[lane * 3 + > + ctx->sata_param.speed[lane]]); > + val = RXTX_REG125_PHZ_MANUAL_SET(val, 0x1); > + serdes_wr(ctx, lane, RXTX_REG125, val); > + > + serdes_rd(ctx, lane, RXTX_REG127, &val); > + val = RXTX_REG127_LATCH_MAN_CAL_ENA_SET(val, 0x0); > + serdes_wr(ctx, lane, RXTX_REG127, val); > + > + serdes_rd(ctx, lane, RXTX_REG128, &val); > + val = RXTX_REG128_LATCH_CAL_WAIT_SEL_SET(val, 0x3); > + serdes_wr(ctx, lane, RXTX_REG128, val); > + > + serdes_rd(ctx, lane, RXTX_REG145, &val); > + val = RXTX_REG145_RXDFE_CONFIG_SET(val, 0x3); > + val = RXTX_REG145_TX_IDLE_SATA_SET(val, 0x0); > + if (preA3Chip) { > + val = RXTX_REG145_RXES_ENA_SET(val, 0x1); > + val = RXTX_REG145_RXVWES_LATENA_SET(val, 0x1); > + } else { > + val = RXTX_REG145_RXES_ENA_SET(val, 0x0); > + val = RXTX_REG145_RXVWES_LATENA_SET(val, 0x0); > + } > + serdes_wr(ctx, lane, RXTX_REG145, val); > + > + /* > + * Set Rx LOS filter clock rate, sample rate, and threshold > + * windows > + */ > + for (i = 0; i < 4; i++) { > + reg = RXTX_REG148 + i * 2; > + serdes_wr(ctx, lane, reg, 0xFFFF); > + } > + } > +} > + > +static int xgene_phy_cal_rdy_chk(struct xgene_phy_ctx *ctx, > + enum cmu_type_t cmu_type, > + enum clk_type_t clk_type) > +{ > + void __iomem *csr_serdes = ctx->sds_base; > + int loop; > + u32 val; > + > + /* Release PHY main reset */ > + writel(0xdf, csr_serdes + SATA_ENET_SDS_RST_CTL); > + readl(csr_serdes + SATA_ENET_SDS_RST_CTL); /* Force a barrier */ > + > + if (cmu_type != REF_CMU) { > + cmu_setbits(ctx, cmu_type, CMU_REG5, CMU_REG5_PLL_RESETB_MASK); > + /* > + * As per PHY design spec, the PLL reset requires a minimum > + * of 800us. > + */ > + usleep_range(800, 1000); > + > + cmu_rd(ctx, cmu_type, CMU_REG1, &val); > + val = CMU_REG1_PLL_MANUALCAL_SET(val, 0x0); > + cmu_wr(ctx, cmu_type, CMU_REG1, val); > + /* > + * As per PHY design spec, the PLL auto calibration requires > + * a minimum of 800us. > + */ > + usleep_range(800, 1000); > + > + cmu_toggle1to0(ctx, cmu_type, CMU_REG32, > + CMU_REG32_FORCE_VCOCAL_START_MASK); > + /* > + * As per PHY design spec, the PLL requires a minimum of > + * 800us to settle. > + */ > + usleep_range(800, 1000); > + } > + > + if (!preA3Chip) > + goto skip_manual_cal; > + > + /* > + * Configure the termination resister calibration > + * The serial receive pins, RXP/RXN, have TERMination resistor > + * that is required to be calibrated. > + */ > + cmu_rd(ctx, cmu_type, CMU_REG17, &val); > + val = CMU_REG17_PVT_CODE_R2A_SET(val, 0x12); > + val = CMU_REG17_RESERVED_7_SET(val, 0x0); > + cmu_wr(ctx, cmu_type, CMU_REG17, val); > + cmu_toggle1to0(ctx, cmu_type, CMU_REG17, > + CMU_REG17_PVT_TERM_MAN_ENA_MASK); > + /* > + * The serial transmit pins, TXP/TXN, have Pull-UP and Pull-DOWN > + * resistors that are required to the calibrated. > + * Configure the pull DOWN calibration > + */ > + cmu_rd(ctx, cmu_type, CMU_REG17, &val); > + val = CMU_REG17_PVT_CODE_R2A_SET(val, 0x29); > + val = CMU_REG17_RESERVED_7_SET(val, 0x0); > + cmu_wr(ctx, cmu_type, CMU_REG17, val); > + cmu_toggle1to0(ctx, cmu_type, CMU_REG16, > + CMU_REG16_PVT_DN_MAN_ENA_MASK); > + /* Configure the pull UP calibration */ > + cmu_rd(ctx, cmu_type, CMU_REG17, &val); > + val = CMU_REG17_PVT_CODE_R2A_SET(val, 0x28); > + val = CMU_REG17_RESERVED_7_SET(val, 0x0); > + cmu_wr(ctx, cmu_type, CMU_REG17, val); > + cmu_toggle1to0(ctx, cmu_type, CMU_REG16, > + CMU_REG16_PVT_UP_MAN_ENA_MASK); > + > +skip_manual_cal: > + /* Poll the PLL calibration completion status for at least 1 ms */ > + loop = 100; > + do { > + cmu_rd(ctx, cmu_type, CMU_REG7, &val); > + if (CMU_REG7_PLL_CALIB_DONE_RD(val)) > + break; > + /* > + * As per PHY design spec, PLL calibration status requires > + * a minimum of 10us to be updated. > + */ > + usleep_range(10, 100); > + } while (--loop > 0); > + > + cmu_rd(ctx, cmu_type, CMU_REG7, &val); > + dev_dbg(ctx->dev, "PLL calibration %s\n", > + CMU_REG7_PLL_CALIB_DONE_RD(val) ? "done" : "failed"); > + if (CMU_REG7_VCO_CAL_FAIL_RD(val)) { > + dev_err(ctx->dev, > + "PLL calibration failed due to VCO failure\n"); > + return -1; > + } > + dev_dbg(ctx->dev, "PLL calibration successful\n"); > + > + cmu_rd(ctx, cmu_type, CMU_REG15, &val); > + dev_dbg(ctx->dev, "PHY Tx is %sready\n", val & 0x300 ? "" : "not "); > + return 0; > +} > + > +static void xgene_phy_pdwn_force_vco(struct xgene_phy_ctx *ctx, > + enum cmu_type_t cmu_type, > + enum clk_type_t clk_type) > +{ > + u32 val; > + > + dev_dbg(ctx->dev, "Reset VCO and re-start again\n"); > + if (cmu_type == PHY_CMU) { > + cmu_rd(ctx, cmu_type, CMU_REG16, &val); > + val = CMU_REG16_VCOCAL_WAIT_BTW_CODE_SET(val, 0x7); > + cmu_wr(ctx, cmu_type, CMU_REG16, val); > + } > + > + cmu_toggle1to0(ctx, cmu_type, CMU_REG0, CMU_REG0_PDOWN_MASK); > + cmu_toggle1to0(ctx, cmu_type, CMU_REG32, > + CMU_REG32_FORCE_VCOCAL_START_MASK); > +} > + > +static int xgene_phy_hw_init_sata(struct xgene_phy_ctx *ctx, > + enum clk_type_t clk_type, int ssc_enable) > +{ > + void __iomem *sds_base = ctx->sds_base; > + u32 val; > + int i; > + > + /* Configure the PHY for operation */ > + dev_dbg(ctx->dev, "Reset PHY\n"); > + /* Place PHY into reset */ > + writel(0x0, sds_base + SATA_ENET_SDS_RST_CTL); > + val = readl(sds_base + SATA_ENET_SDS_RST_CTL); /* Force a barrier */ > + /* Release PHY lane from reset (active high) */ > + writel(0x20, sds_base + SATA_ENET_SDS_RST_CTL); > + readl(sds_base + SATA_ENET_SDS_RST_CTL); /* Force a barrier */ > + /* Release all PHY module out of reset except PHY main reset */ > + writel(0xde, sds_base + SATA_ENET_SDS_RST_CTL); > + readl(sds_base + SATA_ENET_SDS_RST_CTL); /* Force a barrier */ > + > + /* Set the operation speed */ > + val = readl(sds_base + SATA_ENET_SDS_CTL1); > + val = CFG_I_SPD_SEL_CDR_OVR1_SET(val, > + ctx->sata_param.txspeed[ctx->sata_param.speed[0]]); > + writel(val, sds_base + SATA_ENET_SDS_CTL1); > + > + dev_dbg(ctx->dev, "Set the customer pin mode to SATA\n"); > + val = readl(sds_base + SATA_ENET_SDS_CTL0); > + val = REGSPEC_CFG_I_CUSTOMER_PIN_MODE0_SET(val, 0x4421); > + writel(val, sds_base + SATA_ENET_SDS_CTL0); > + > + /* Configure the clock macro unit (CMU) clock type */ > + xgene_phy_cfg_cmu_clk_type(ctx, PHY_CMU, clk_type); > + > + /* Configure the clock macro */ > + xgene_phy_sata_cfg_cmu_core(ctx, PHY_CMU, clk_type); > + > + /* Enable SSC if enabled */ > + if (ssc_enable) > + xgene_phy_ssc_enable(ctx, PHY_CMU); > + > + /* Configure PHY lanes */ > + xgene_phy_sata_cfg_lanes(ctx); > + > + /* Set Rx/Tx 20-bit */ > + val = readl(sds_base + SATA_ENET_SDS_PCS_CTL0); > + val = REGSPEC_CFG_I_RX_WORDMODE0_SET(val, 0x3); > + val = REGSPEC_CFG_I_TX_WORDMODE0_SET(val, 0x3); > + writel(val, sds_base + SATA_ENET_SDS_PCS_CTL0); > + > + /* Start PLL calibration and try for three times */ > + i = 10; > + do { > + if (!xgene_phy_cal_rdy_chk(ctx, PHY_CMU, clk_type)) > + break; > + /* If failed, toggle the VCO power signal and start again */ > + xgene_phy_pdwn_force_vco(ctx, PHY_CMU, clk_type); > + } while (--i > 0); > + /* Even on failure, allow to continue any way */ > + if (i <= 0) > + dev_err(ctx->dev, "PLL calibration failed\n"); > + > + return 0; > +} > + > +static int xgene_phy_hw_initialize(struct xgene_phy_ctx *ctx, > + enum clk_type_t clk_type, > + int ssc_enable) > +{ > + int rc; > + > + dev_dbg(ctx->dev, "PHY init clk type %d\n", clk_type); > + > + if (ctx->mode == MODE_SATA) { > + rc = xgene_phy_hw_init_sata(ctx, clk_type, ssc_enable); > + if (rc) > + return rc; > + } else { > + dev_err(ctx->dev, "Un-supported customer pin mode %d\n", > + ctx->mode); > + return -ENODEV; > + } > + > + return 0; > +} > + > +/* > + * Receiver Offset Calibration: > + * > + * Calibrate the receiver signal path offset in two steps - summar and > + * latch calibrations > + */ > +static void xgene_phy_force_lat_summer_cal(struct xgene_phy_ctx *ctx, int lane) > +{ > + int i; > + struct { > + u32 reg; > + u32 val; > + } serdes_reg[] = { > + {RXTX_REG38, 0x0}, > + {RXTX_REG39, 0xff00}, > + {RXTX_REG40, 0xffff}, > + {RXTX_REG41, 0xffff}, > + {RXTX_REG42, 0xffff}, > + {RXTX_REG43, 0xffff}, > + {RXTX_REG44, 0xffff}, > + {RXTX_REG45, 0xffff}, > + {RXTX_REG46, 0xffff}, > + {RXTX_REG47, 0xfffc}, > + {RXTX_REG48, 0x0}, > + {RXTX_REG49, 0x0}, > + {RXTX_REG50, 0x0}, > + {RXTX_REG51, 0x0}, > + {RXTX_REG52, 0x0}, > + {RXTX_REG53, 0x0}, > + {RXTX_REG54, 0x0}, > + {RXTX_REG55, 0x0}, > + }; > + > + /* Start SUMMER calibration */ > + serdes_setbits(ctx, lane, RXTX_REG127, > + RXTX_REG127_FORCE_SUM_CAL_START_MASK); > + /* > + * As per PHY design spec, the Summer calibration requires a minimum > + * of 100us to complete. > + */ > + usleep_range(100, 500); > + serdes_clrbits(ctx, lane, RXTX_REG127, > + RXTX_REG127_FORCE_SUM_CAL_START_MASK); > + /* > + * As per PHY design spec, the auto calibration requires a minimum > + * of 100us to complete. > + */ > + usleep_range(100, 500); > + > + /* Start latch calibration */ > + serdes_setbits(ctx, lane, RXTX_REG127, > + RXTX_REG127_FORCE_LAT_CAL_START_MASK); > + /* > + * As per PHY design spec, the latch calibration requires a minimum > + * of 100us to complete. > + */ > + usleep_range(100, 500); > + serdes_clrbits(ctx, lane, RXTX_REG127, > + RXTX_REG127_FORCE_LAT_CAL_START_MASK); > + > + /* Configure the PHY lane for calibration */ > + serdes_wr(ctx, lane, RXTX_REG28, 0x7); > + serdes_wr(ctx, lane, RXTX_REG31, 0x7e00); > + serdes_clrbits(ctx, lane, RXTX_REG4, > + RXTX_REG4_TX_LOOPBACK_BUF_EN_MASK); > + serdes_clrbits(ctx, lane, RXTX_REG7, > + RXTX_REG7_LOOP_BACK_ENA_CTLE_MASK); > + for (i = 0; i < ARRAY_SIZE(serdes_reg); i++) > + serdes_wr(ctx, lane, serdes_reg[i].reg, > + serdes_reg[i].val); > +} > + > +static void xgene_phy_reset_rxd(struct xgene_phy_ctx *ctx, int lane) > +{ > + /* Reset digital Rx */ > + serdes_clrbits(ctx, lane, RXTX_REG7, RXTX_REG7_RESETB_RXD_MASK); > + /* As per PHY design spec, the reset requires a minimum of 100us. */ > + usleep_range(100, 150); > + serdes_setbits(ctx, lane, RXTX_REG7, RXTX_REG7_RESETB_RXD_MASK); > +} > + > +static int xgene_phy_get_avg(int accum, int samples) > +{ > + return (accum + (samples / 2)) / samples; > +} > + > +static void xgene_phy_gen_avg_val(struct xgene_phy_ctx *ctx, int lane) > +{ > + int max_loop = 10; > + int avg_loop = 0; > + int lat_do = 0, lat_xo = 0, lat_eo = 0, lat_so = 0; > + int lat_de = 0, lat_xe = 0, lat_ee = 0, lat_se = 0; > + int sum_cal = 0; > + int lat_do_itr, lat_xo_itr, lat_eo_itr, lat_so_itr; > + int lat_de_itr, lat_xe_itr, lat_ee_itr, lat_se_itr; > + int sum_cal_itr; > + int fail_even; > + int fail_odd; > + u32 val; > + > + dev_dbg(ctx->dev, "Generating avg calibration value for lane %d\n", > + lane); > + > + /* Enable RX Hi-Z termination */ > + serdes_setbits(ctx, lane, RXTX_REG12, > + RXTX_REG12_RX_DET_TERM_ENABLE_MASK); > + /* Turn off DFE */ > + serdes_wr(ctx, lane, RXTX_REG28, 0x0000); > + /* DFE Presets to zero */ > + serdes_wr(ctx, lane, RXTX_REG31, 0x0000); > + > + /* > + * Receiver Offset Calibration: > + * Calibrate the receiver signal path offset in two steps - summar > + * and latch calibration. > + * Runs the "Receiver Offset Calibration multiple times to determine > + * the average value to use. > + */ > + while (avg_loop < max_loop) { > + /* Start the calibration */ > + xgene_phy_force_lat_summer_cal(ctx, lane); > + > + serdes_rd(ctx, lane, RXTX_REG21, &val); > + lat_do_itr = RXTX_REG21_DO_LATCH_CALOUT_RD(val); > + lat_xo_itr = RXTX_REG21_XO_LATCH_CALOUT_RD(val); > + fail_odd = RXTX_REG21_LATCH_CAL_FAIL_ODD_RD(val); > + > + serdes_rd(ctx, lane, RXTX_REG22, &val); > + lat_eo_itr = RXTX_REG22_EO_LATCH_CALOUT_RD(val); > + lat_so_itr = RXTX_REG22_SO_LATCH_CALOUT_RD(val); > + fail_even = RXTX_REG22_LATCH_CAL_FAIL_EVEN_RD(val); > + > + serdes_rd(ctx, lane, RXTX_REG23, &val); > + lat_de_itr = RXTX_REG23_DE_LATCH_CALOUT_RD(val); > + lat_xe_itr = RXTX_REG23_XE_LATCH_CALOUT_RD(val); > + > + serdes_rd(ctx, lane, RXTX_REG24, &val); > + lat_ee_itr = RXTX_REG24_EE_LATCH_CALOUT_RD(val); > + lat_se_itr = RXTX_REG24_SE_LATCH_CALOUT_RD(val); > + > + serdes_rd(ctx, lane, RXTX_REG121, &val); > + sum_cal_itr = RXTX_REG121_SUMOS_CAL_CODE_RD(val); > + > + /* Check for failure. If passed, sum them for averaging */ > + if ((fail_even == 0 || fail_even == 1) && > + (fail_odd == 0 || fail_odd == 1)) { > + lat_do += lat_do_itr; > + lat_xo += lat_xo_itr; > + lat_eo += lat_eo_itr; > + lat_so += lat_so_itr; > + lat_de += lat_de_itr; > + lat_xe += lat_xe_itr; > + lat_ee += lat_ee_itr; > + lat_se += lat_se_itr; > + sum_cal += sum_cal_itr; > + > + dev_dbg(ctx->dev, "Iteration %d:\n", avg_loop); > + dev_dbg(ctx->dev, "DO 0x%x XO 0x%x EO 0x%x SO 0x%x\n", > + lat_do_itr, lat_xo_itr, lat_eo_itr, > + lat_so_itr); > + dev_dbg(ctx->dev, "DE 0x%x XE 0x%x EE 0x%x SE 0x%x\n", > + lat_de_itr, lat_xe_itr, lat_ee_itr, > + lat_se_itr); > + dev_dbg(ctx->dev, "SUM 0x%x\n", sum_cal_itr); > + ++avg_loop; > + } else { > + dev_err(ctx->dev, > + "Receiver calibration failed at %d loop\n", > + avg_loop); > + } > + xgene_phy_reset_rxd(ctx, lane); > + } > + > + /* Update latch manual calibration with average value */ > + serdes_rd(ctx, lane, RXTX_REG127, &val); > + val = RXTX_REG127_DO_LATCH_MANCAL_SET(val, > + xgene_phy_get_avg(lat_do, max_loop)); > + val = RXTX_REG127_XO_LATCH_MANCAL_SET(val, > + xgene_phy_get_avg(lat_xo, max_loop)); > + serdes_wr(ctx, lane, RXTX_REG127, val); > + > + serdes_rd(ctx, lane, RXTX_REG128, &val); > + val = RXTX_REG128_EO_LATCH_MANCAL_SET(val, > + xgene_phy_get_avg(lat_eo, max_loop)); > + val = RXTX_REG128_SO_LATCH_MANCAL_SET(val, > + xgene_phy_get_avg(lat_so, max_loop)); > + serdes_wr(ctx, lane, RXTX_REG128, val); > + > + serdes_rd(ctx, lane, RXTX_REG129, &val); > + val = RXTX_REG129_DE_LATCH_MANCAL_SET(val, > + xgene_phy_get_avg(lat_de, max_loop)); > + val = RXTX_REG129_XE_LATCH_MANCAL_SET(val, > + xgene_phy_get_avg(lat_xe, max_loop)); > + serdes_wr(ctx, lane, RXTX_REG129, val); > + > + serdes_rd(ctx, lane, RXTX_REG130, &val); > + val = RXTX_REG130_EE_LATCH_MANCAL_SET(val, > + xgene_phy_get_avg(lat_ee, max_loop)); > + val = RXTX_REG130_SE_LATCH_MANCAL_SET(val, > + xgene_phy_get_avg(lat_se, max_loop)); > + serdes_wr(ctx, lane, RXTX_REG130, val); > + > + /* Update SUMMER calibration with average value */ > + serdes_rd(ctx, lane, RXTX_REG14, &val); > + val = RXTX_REG14_CLTE_LATCAL_MAN_PROG_SET(val, > + xgene_phy_get_avg(sum_cal, max_loop)); > + serdes_wr(ctx, lane, RXTX_REG14, val); > + > + dev_dbg(ctx->dev, "Average Value:\n"); > + dev_dbg(ctx->dev, "DO 0x%x XO 0x%x EO 0x%x SO 0x%x\n", > + xgene_phy_get_avg(lat_do, max_loop), > + xgene_phy_get_avg(lat_xo, max_loop), > + xgene_phy_get_avg(lat_eo, max_loop), > + xgene_phy_get_avg(lat_so, max_loop)); > + dev_dbg(ctx->dev, "DE 0x%x XE 0x%x EE 0x%x SE 0x%x\n", > + xgene_phy_get_avg(lat_de, max_loop), > + xgene_phy_get_avg(lat_xe, max_loop), > + xgene_phy_get_avg(lat_ee, max_loop), > + xgene_phy_get_avg(lat_se, max_loop)); > + dev_dbg(ctx->dev, "SUM 0x%x\n", > + xgene_phy_get_avg(sum_cal, max_loop)); > + > + serdes_rd(ctx, lane, RXTX_REG14, &val); > + val = RXTX_REG14_CTLE_LATCAL_MAN_ENA_SET(val, 0x1); > + serdes_wr(ctx, lane, RXTX_REG14, val); > + dev_dbg(ctx->dev, "Enable Manual Summer calibration\n"); > + > + serdes_rd(ctx, lane, RXTX_REG127, &val); > + val = RXTX_REG127_LATCH_MAN_CAL_ENA_SET(val, 0x1); > + dev_dbg(ctx->dev, "Enable Manual Latch calibration\n"); > + serdes_wr(ctx, lane, RXTX_REG127, val); > + > + /* Disable RX Hi-Z termination */ > + serdes_rd(ctx, lane, RXTX_REG12, &val); > + val = RXTX_REG12_RX_DET_TERM_ENABLE_SET(val, 0); > + serdes_wr(ctx, lane, RXTX_REG12, val); > + /* Turn on DFE */ > + serdes_wr(ctx, lane, RXTX_REG28, 0x0007); > + /* Set DFE preset */ > + serdes_wr(ctx, lane, RXTX_REG31, 0x7e00); > +} > + > +static int xgene_phy_hw_init(struct phy *phy) > +{ > + struct xgene_phy_ctx *ctx = phy_get_drvdata(phy); > + int rc; > + int i; > + > + rc = xgene_phy_hw_initialize(ctx, CLK_EXT_DIFF, SSC_DISABLE); > + if (rc) { > + dev_err(ctx->dev, "PHY initialize failed %d\n", rc); > + return rc; > + } > + > + /* Setup clock properly after PHY configuration */ > + if (!IS_ERR(ctx->clk)) { > + /* HW requires an toggle of the clock */ > + clk_prepare_enable(ctx->clk); > + clk_disable_unprepare(ctx->clk); > + clk_prepare_enable(ctx->clk); > + } > + > + /* Compute average value */ > + for (i = 0; i < MAX_LANE; i++) > + xgene_phy_gen_avg_val(ctx, i); > + > + dev_dbg(ctx->dev, "PHY initialized\n"); > + return 0; > +} > + > +static const struct phy_ops xgene_phy_ops = { > + .init = xgene_phy_hw_init, > + .owner = THIS_MODULE, > +}; > + > +static struct phy *xgene_phy_xlate(struct device *dev, > + struct of_phandle_args *args) > +{ > + struct xgene_phy_ctx *ctx = dev_get_drvdata(dev); > + > + if (args->args_count <= 0) > + return ERR_PTR(-EINVAL); > + if (args->args[0] < MODE_SATA || args->args[0] >= MODE_MAX) > + return ERR_PTR(-EINVAL); > + > + ctx->mode = args->args[0]; > + return ctx->phy; > +} > + > +static void xgene_phy_get_param(struct platform_device *pdev, > + const char *name, u32 *buffer, > + int count, u32 *default_val, > + u32 conv_factor) > +{ > + int i; > + > + if (!of_property_read_u32_array(pdev->dev.of_node, name, buffer, > + count)) { > + for (i = 0; i < count; i++) > + buffer[i] /= conv_factor; > + return; > + } > + /* Does not exist, load default */ > + for (i = 0; i < count; i++) > + buffer[i] = default_val[i % 3]; > +} > + > +static int xgene_phy_probe(struct platform_device *pdev) > +{ > + struct phy_provider *phy_provider; > + struct xgene_phy_ctx *ctx; > + struct resource *res; > + int rc = 0; > + u32 default_spd[] = DEFAULT_SATA_SPD_SEL; > + u32 default_txboost_gain[] = DEFAULT_SATA_TXBOOST_GAIN; > + u32 default_txeye_direction[] = DEFAULT_SATA_TXEYEDIRECTION; > + u32 default_txeye_tuning[] = DEFAULT_SATA_TXEYETUNING; > + u32 default_txamp[] = DEFAULT_SATA_TXAMP; > + u32 default_txcn1[] = DEFAULT_SATA_TXCN1; > + u32 default_txcn2[] = DEFAULT_SATA_TXCN2; > + u32 default_txcp1[] = DEFAULT_SATA_TXCP1; > + int i; > + > + ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL); > + if (!ctx) > + return -ENOMEM; > + > + ctx->dev = &pdev->dev; > + > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + ctx->sds_base = devm_ioremap_resource(&pdev->dev, res); > + if (IS_ERR(ctx->sds_base)) { > + rc = PTR_ERR(ctx->sds_base); > + goto error; > + } > + > + /* Retrieve optional clock */ > + ctx->clk = clk_get(&pdev->dev, NULL); > + > + /* Load override paramaters */ > + xgene_phy_get_param(pdev, "apm,tx-eye-tuning", > + ctx->sata_param.txeyetuning, 6, default_txeye_tuning, 1); > + xgene_phy_get_param(pdev, "apm,tx-eye-direction", > + ctx->sata_param.txeyedirection, 6, default_txeye_direction, 1); > + xgene_phy_get_param(pdev, "apm,tx-boost-gain", > + ctx->sata_param.txboostgain, 6, default_txboost_gain, 1); > + xgene_phy_get_param(pdev, "apm,tx-amplitude", > + ctx->sata_param.txamplitude, 6, default_txamp, 13300); > + xgene_phy_get_param(pdev, "apm,tx-pre-cursor1", > + ctx->sata_param.txprecursor_cn1, 6, default_txcn1, 18200); > + xgene_phy_get_param(pdev, "apm,tx-pre-cursor2", > + ctx->sata_param.txprecursor_cn2, 6, default_txcn2, 18200); > + xgene_phy_get_param(pdev, "apm,tx-post-cursor", > + ctx->sata_param.txpostcursor_cp1, 6, default_txcp1, 18200); > + xgene_phy_get_param(pdev, "apm,tx-speed", > + ctx->sata_param.txspeed, 3, default_spd, 1); > + for (i = 0; i < MAX_LANE; i++) > + ctx->sata_param.speed[i] = 2; /* Default to Gen3 */ > + > + ctx->dev = &pdev->dev; > + platform_set_drvdata(pdev, ctx); > + > + ctx->phy = devm_phy_create(ctx->dev, &xgene_phy_ops, NULL); > + if (IS_ERR(ctx->phy)) { > + dev_dbg(&pdev->dev, "Failed to create PHY\n"); > + rc = PTR_ERR(ctx->phy); > + goto error; > + } > + phy_set_drvdata(ctx->phy, ctx); > + > + phy_provider = devm_of_phy_provider_register(ctx->dev, > + xgene_phy_xlate); > + if (IS_ERR(phy_provider)) { > + rc = PTR_ERR(phy_provider); > + goto error; > + } > + > + return 0; > + > +error: > + return rc; > +} > + > +static const struct of_device_id xgene_phy_of_match[] = { > + {.compatible = "apm,xgene-phy",}, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, xgene_phy_of_match); > + > +static struct platform_driver xgene_phy_driver = { > + .probe = xgene_phy_probe, > + .driver = { > + .name = "xgene-phy", > + .owner = THIS_MODULE, > + .of_match_table = xgene_phy_of_match, > + }, > +}; > +module_platform_driver(xgene_phy_driver); > + > +MODULE_DESCRIPTION("APM X-Gene Multi-Purpose PHY driver"); > +MODULE_AUTHOR("Loc Ho <lho@apm.com>"); > +MODULE_LICENSE("GPL v2"); > +MODULE_VERSION("0.1"); > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt b/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt new file mode 100644 index 0000000..5f3a65a --- /dev/null +++ b/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt @@ -0,0 +1,79 @@ +* APM X-Gene 15Gbps Multi-purpose PHY nodes + +PHY nodes are defined to describe on-chip 15Gbps Multi-purpose PHY. Each +PHY (pair of lanes) has its own node. + +Required properties: +- compatible : Shall be "apm,xgene-phy". +- reg : PHY memory resource is the SDS PHY access resource. +- #phy-cells : Shall be 1 as it expects one argument for setting + the mode of the PHY. Possible values are 0 (SATA), + 1 (SGMII), 2 (PCIe), 3 (USB), and 4 (XFI). + +Optional properties: +- status : Shall be "ok" if enabled or "disabled" if disabled. + Default is "ok". +- clocks : Reference to the clock entry. +- apm,tx-eye-tuning : Manual control to fine tune the capture of the serial + bit lines from the automatic calibrated position. + Two set of 3-tuple setting for each (up to 3) + supported link speed on the host. Range from 0 to + 127 in unit of one bit period. Default is 10. +- apm,tx-eye-direction : Eye tuning manual control direction. 0 means sample + data earlier than the nominal sampling point. 1 means + sample data later than the nominal sampling point. + Two set of 3-tuple setting for each (up to 3) + supported link speed on the host. Default is 0. +- apm,tx-boost-gain : Frequency boost AC (LSB 3-bit) and DC (2-bit) + gain control. Two set of 3-tuple setting for each + (up to 3) supported link speed on the host. Range is + between 0 to 31 in unit of dB. Default is 3. +- apm,tx-amplitude : Amplitude control. Two set of 3-tuple setting for + each (up to 3) supported link speed on the host. + Range is between 0 to 199500 in unit of uV. + Default is 199500 uV. +- apm,tx-pre-cursor1 : 1st pre-cursor emphasis taps control. Two set of + 3-tuple setting for each (up to 3) supported link + speed on the host. Range is 0 to 273000 in unit of + uV. Default is 0. +- apm,tx-pre-cursor2 : 2st pre-cursor emphasis taps control. Two set of + 3-tuple setting for each (up to 3) supported link + speed on the host. Range is 0 to 127400 in unit uV. + Default is 0x0. +- apm,tx-post-cursor : Post-cursor emphasis taps control. Two set of + 3-tuple setting for Gen1, Gen2, and Gen3. Range is + between 0 to 0x1f in unit of 18.2mV. Default is 0xf. +- apm,tx-speed : Tx operating speed. One set of 3-tuple for each + supported link speed on the host. + 0 = 1-2Gbps + 1 = 2-4Gbps (1st tuple default) + 2 = 4-8Gbps + 3 = 8-15Gbps (2nd tuple default) + 4 = 2.5-4Gbps + 5 = 4-5Gbps + 6 = 5-6Gbps + 7 = 6-16Gbps (3rd tuple default) + +NOTE: PHY override parameters are board specific setting. + +Example: + phy1: phy@1f21a000 { + compatible = "apm,xgene-phy"; + reg = <0x0 0x1f21a000 0x0 0x100>; + #phy-cells = <1>; + status = "disabled"; + }; + + phy2: phy@1f22a000 { + compatible = "apm,xgene-phy"; + reg = <0x0 0x1f22a000 0x0 0x100>; + #phy-cells = <1>; + status = "ok"; + }; + + phy3: phy@1f23a000 { + compatible = "apm,xgene-phy"; + reg = <0x0 0x1f23a000 0x0 0x100>; + #phy-cells = <1>; + status = "ok"; + };