@@ -11,6 +11,7 @@
#define SOCFPGA_UART0_ADDRESS 0xffc02000
#define SOCFPGA_UART1_ADDRESS 0xffc03000
#define SOCFPGA_OSC1TIMER0_ADDRESS 0xffd00000
+#define SOCFPGA_L4WD0_ADDRESS 0xffd02000
#define SOCFPGA_CLKMGR_ADDRESS 0xffd04000
#define SOCFPGA_RSTMGR_ADDRESS 0xffd05000
#define SOCFPGA_SYSMGR_ADDRESS 0xffd08000
@@ -15,3 +15,4 @@ obj-$(CONFIG_S5P) += s5p_wdt.o
obj-$(CONFIG_XILINX_TB_WATCHDOG) += xilinx_tb_wdt.o
obj-$(CONFIG_BFIN_WATCHDOG) += bfin_wdt.o
obj-$(CONFIG_OMAP_WATCHDOG) += omap_wdt.o
+obj-$(CONFIG_DESIGNWARE_WATCHDOG) += designware_wdt.o
new file mode 100644
@@ -0,0 +1,73 @@
+/*
+ * Copyright (C) 2013 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <watchdog.h>
+#include <asm/io.h>
+#include <asm/utils.h>
+
+#define DW_WDT_CR 0x00
+#define DW_WDT_TORR 0x04
+#define DW_WDT_CRR 0x0C
+
+#define DW_WDT_CR_EN_OFFSET 0x00
+#define DW_WDT_CR_RMOD_OFFSET 0x01
+#define DW_WDT_CR_RMOD_VAL 0x00
+#define DW_WDT_CRR_RESTART_VAL 0x76
+
+/*
+ * Set the watchdog time interval.
+ * Counter is 32 bit.
+ */
+int designware_wdt_settimeout(unsigned int timeout)
+{
+ signed int i;
+ /* calculate the timeout range value */
+ i = (log_2_n_round_up(timeout * CONFIG_DW_WDT_CLOCK_KHZ)) - 16;
+ if (i > 15)
+ i = 15;
+ if (i < 0)
+ i = 0;
+
+ writel((i | (i<<4)), (CONFIG_DW_WDT_BASE + DW_WDT_TORR));
+ return 0;
+}
+
+void designware_wdt_enable(void)
+{
+ writel(((DW_WDT_CR_RMOD_VAL << DW_WDT_CR_RMOD_OFFSET) | \
+ (0x1 << DW_WDT_CR_EN_OFFSET)),
+ (CONFIG_DW_WDT_BASE + DW_WDT_CR));
+}
+
+unsigned int designware_wdt_is_enabled(void)
+{
+ unsigned long val;
+ val = readl((CONFIG_DW_WDT_BASE + DW_WDT_CR));
+ return val & 0x1;
+}
+
+#if defined(CONFIG_HW_WATCHDOG)
+void hw_watchdog_reset(void)
+{
+ if (designware_wdt_is_enabled())
+ /* restart the watchdog counter */
+ writel(DW_WDT_CRR_RESTART_VAL,
+ (CONFIG_DW_WDT_BASE + DW_WDT_CRR));
+}
+
+void hw_watchdog_init(void)
+{
+ /* reset to disable the watchdog */
+ hw_watchdog_reset();
+ /* set timer in miliseconds */
+ designware_wdt_settimeout(CONFIG_HW_WATCHDOG_TIMEOUT_MS);
+ /* enable the watchdog */
+ designware_wdt_enable();
+ /* reset the watchdog */
+ hw_watchdog_reset();
+}
+#endif
@@ -207,6 +207,16 @@
#define CONFIG_ENV_IS_NOWHERE
/*
+ * L4 Watchdog
+ */
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_HW_WATCHDOG_TIMEOUT_MS 2000
+#define CONFIG_DESIGNWARE_WATCHDOG
+#define CONFIG_DW_WDT_BASE SOCFPGA_L4WD0_ADDRESS
+/* Clocks source frequency to watchdog timer */
+#define CONFIG_DW_WDT_CLOCK_KHZ 25000
+
+/*
* SPL "Second Program Loader" aka Initial Software
*/
@@ -238,4 +248,7 @@
/* Support for lib/libgeneric.o in SPL binary */
#define CONFIG_SPL_LIBGENERIC_SUPPORT
+/* Support for watchdog */
+#define CONFIG_SPL_WATCHDOG_SUPPORT
+
#endif /* __CONFIG_H */
To add the DesignWare watchdog driver support. It required information such as register base address and clock info from configuration header file within include/configs folder. Signed-off-by: Chin Liang See <clsee@altera.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com> --- Changes for v2 - Enable this driver at socfpga_cyclone5 board --- .../include/asm/arch-socfpga/socfpga_base_addrs.h | 1 + drivers/watchdog/Makefile | 1 + drivers/watchdog/designware_wdt.c | 73 ++++++++++++++++++++ include/configs/socfpga_cyclone5.h | 13 ++++ 4 files changed, 88 insertions(+) create mode 100644 drivers/watchdog/designware_wdt.c