diff mbox

[v11,10/10] mtd: nand: omap: remove selection of BCH ecc-scheme via KConfig

Message ID 1382619026-4182-11-git-send-email-pekon@ti.com
State New, archived
Headers show

Commit Message

pekon gupta Oct. 24, 2013, 12:50 p.m. UTC 
With OMAP NAND driver updates, selection of ecc-scheme:
*DT enabled kernel*
 	depends on ti,nand-ecc-opt and ti,elm-id DT bindings.
*Non DT enabled kernel*
	depends on elm_dev and ecc-scheme passed along with platform-data
	from board file.

So, selection of ecc-scheme (BCH8 or BCH4) from KConfig can be removed

Signed-off-by: Pekon Gupta <pekon@ti.com>
---
 drivers/mtd/nand/Kconfig | 40 ++++++----------------------------------
 1 file changed, 6 insertions(+), 34 deletions(-)
diff mbox

Patch

diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index d885298..93ae6a6 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -96,43 +96,15 @@  config MTD_NAND_OMAP2
 
 config MTD_NAND_OMAP_BCH
 	depends on MTD_NAND && MTD_NAND_OMAP2 && ARCH_OMAP3
-	tristate "Enable support for hardware BCH error correction"
+	tristate "Support hardware based BCH error correction"
 	default n
 	select BCH
-	select BCH_CONST_PARAMS
 	help
-	 Support for hardware BCH error correction.
-
-choice
-	prompt "BCH error correction capability"
-	depends on MTD_NAND_OMAP_BCH
-
-config MTD_NAND_OMAP_BCH8
-	bool "8 bits / 512 bytes (recommended)"
-	help
-	 Support correcting up to 8 bitflips per 512-byte block.
-	 This will use 13 bytes of spare area per 512 bytes of page data.
-	 This is the recommended mode, as 4-bit mode does not work
-	 on some OMAP3 revisions, due to a hardware bug.
-
-config MTD_NAND_OMAP_BCH4
-	bool "4 bits / 512 bytes"
-	help
-	 Support correcting up to 4 bitflips per 512-byte block.
-	 This will use 7 bytes of spare area per 512 bytes of page data.
-	 Note that this mode does not work on some OMAP3 revisions, due to a
-	 hardware bug. Please check your OMAP datasheet before selecting this
-	 mode.
-
-endchoice
-
-if MTD_NAND_OMAP_BCH
-config BCH_CONST_M
-	default 13
-config BCH_CONST_T
-	default 4 if MTD_NAND_OMAP_BCH4
-	default 8 if MTD_NAND_OMAP_BCH8
-endif
+	  This config enables the ELM hardware engine, which can be used to
+	  locate and correct errors when using BCH ECC scheme. This offloads
+	  the cpu from doing ECC error searching and correction. However some
+	  legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine
+	  so they should not enable this config symbol.
 
 config MTD_NAND_IDS
 	tristate