new file mode 100644
@@ -0,0 +1,274 @@
+/*
+ * P1025 TWR Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/{
+ aliases {
+ ethernet3 = &enet3;
+ ethernet4 = &enet4;
+ };
+};
+
+&lbc {
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x4000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 256KB for Vitesse 7385 Switch firmware */
+ reg = <0x0 0x00040000>;
+ label = "NOR Vitesse-7385 Firmware";
+ read-only;
+ };
+
+ partition@40000 {
+ /* 256KB for DTB Image */
+ reg = <0x00040000 0x00040000>;
+ label = "NOR DTB Image";
+ };
+
+ partition@80000 {
+ /* 5.5 MB for Linux Kernel Image */
+ reg = <0x00080000 0x00580000>;
+ label = "NOR Linux Kernel Image";
+ };
+
+ partition@400000 {
+ /* 56.75MB for Root file System */
+ reg = <0x00600000 0x038c0000>;
+ label = "NOR Root File System";
+ };
+
+ partition@ec0000 {
+ /* This location must not be altered */
+ /* 256KB for QE ucode firmware*/
+ reg = <0x03ec0000 0x00040000>;
+ label = "NOR QE microcode firmware";
+ read-only;
+ };
+
+ partition@f00000 {
+ /* This location must not be altered */
+ /* 512KB for u-boot Bootloader Image */
+ /* 512KB for u-boot Environment Variables */
+ reg = <0x03f00000 0x00100000>;
+ label = "NOR U-Boot Image";
+ read-only;
+ };
+ };
+
+};
+
+&soc {
+ usb@22000 {
+ phy_type = "ulpi";
+ };
+
+ mdio@24000 {
+ phy0: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <1 1 0 0>;
+ reg = <0x2>;
+ };
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <2 1 0 0>;
+ reg = <0x1>;
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ mdio@25000 {
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ mdio@26000 {
+ tbi2: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet@b0000 {
+ phy-handle = <&phy0>;
+ phy-connection-type = "rgmii-id";
+
+ };
+
+ enet1: ethernet@b1000 {
+ status = "disabled";
+ };
+
+ enet2: ethernet@b2000 {
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ par_io@e0100 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xe0100 0x60>;
+ ranges = <0x0 0xe0100 0x60>;
+ device_type = "par_io";
+ num-ports = <3>;
+ pio1: ucc_pin@01 {
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
+ 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
+ 0x0 0x17 0x2 0x0 0x2 0x0 /* CLK12 */
+ 0x0 0x18 0x2 0x0 0x1 0x0 /* CLK9 */
+ 0x0 0x7 0x1 0x0 0x2 0x0 /* ENET1_TXD0_SER1_TXD0 */
+ 0x0 0x9 0x1 0x0 0x2 0x0 /* ENET1_TXD1_SER1_TXD1 */
+ 0x0 0xb 0x1 0x0 0x2 0x0 /* ENET1_TXD2_SER1_TXD2 */
+ 0x0 0xc 0x1 0x0 0x2 0x0 /* ENET1_TXD3_SER1_TXD3 */
+ 0x0 0x6 0x2 0x0 0x2 0x0 /* ENET1_RXD0_SER1_RXD0 */
+ 0x0 0xa 0x2 0x0 0x2 0x0 /* ENET1_RXD1_SER1_RXD1 */
+ 0x0 0xe 0x2 0x0 0x2 0x0 /* ENET1_RXD2_SER1_RXD2 */
+ 0x0 0xf 0x2 0x0 0x2 0x0 /* ENET1_RXD3_SER1_RXD3 */
+ 0x0 0x5 0x1 0x0 0x2 0x0 /* ENET1_TX_EN_SER1_RTS_B */
+ 0x0 0xd 0x1 0x0 0x2 0x0 /* ENET1_TX_ER */
+ 0x0 0x4 0x2 0x0 0x2 0x0 /* ENET1_RX_DV_SER1_CTS_B */
+ 0x0 0x8 0x2 0x0 0x2 0x0 /* ENET1_RX_ER_SER1_CD_B */
+ 0x0 0x11 0x2 0x0 0x2 0x0 /* ENET1_CRS */
+ 0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */
+ };
+
+ pio2: ucc_pin@02 {
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
+ 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
+ 0x1 0xb 0x2 0x0 0x1 0x0 /* CLK13 */
+ 0x1 0x7 0x1 0x0 0x2 0x0 /* ENET5_TXD0_SER5_TXD0 */
+ 0x1 0xa 0x1 0x0 0x2 0x0 /* ENET5_TXD1_SER5_TXD1 */
+ 0x1 0x6 0x2 0x0 0x2 0x0 /* ENET5_RXD0_SER5_RXD0 */
+ 0x1 0x9 0x2 0x0 0x2 0x0 /* ENET5_RXD1_SER5_RXD1 */
+ 0x1 0x5 0x1 0x0 0x2 0x0 /* ENET5_TX_EN_SER5_RTS_B */
+ 0x1 0x4 0x2 0x0 0x2 0x0 /* ENET5_RX_DV_SER5_CTS_B */
+ 0x1 0x8 0x2 0x0 0x2 0x0>; /* ENET5_RX_ER_SER5_CD_B */
+ };
+
+ pio3: ucc_pin@03 {
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0x0 0x16 0x2 0x0 0x2 0x0 /* SER7_CD_B*/
+ 0x0 0x12 0x2 0x0 0x2 0x0 /* SER7_CTS_B*/
+ 0x0 0x13 0x1 0x0 0x2 0x0 /* SER7_RTS_B*/
+ 0x0 0x14 0x2 0x0 0x2 0x0 /* SER7_RXD0*/
+ 0x0 0x15 0x1 0x0 0x2 0x0>; /* SER7_TXD0*/
+ };
+
+ pio4: ucc_pin@04 {
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0x1 0x0 0x2 0x0 0x2 0x0 /* SER3_CD_B*/
+ 0x0 0x1c 0x2 0x0 0x2 0x0 /* SER3_CTS_B*/
+ 0x0 0x1d 0x1 0x0 0x2 0x0 /* SER3_RTS_B*/
+ 0x0 0x1e 0x2 0x0 0x2 0x0 /* SER3_RXD0*/
+ 0x0 0x1f 0x1 0x0 0x2 0x0>; /* SER3_TXD0*/
+ };
+ };
+};
+
+&qe {
+ enet3: ucc@2000 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ rx-clock-name = "clk12";
+ tx-clock-name = "clk9";
+ pio-handle = <&pio1>;
+ phy-handle = <&qe_phy0>;
+ phy-connection-type = "mii";
+ };
+
+ mdio@2120 {
+ qe_phy0: ethernet-phy@18 {
+ interrupt-parent = <&mpic>;
+ interrupts = <4 1 0 0>;
+ reg = <0x18>;
+ device_type = "ethernet-phy";
+ };
+ qe_phy1: ethernet-phy@19 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1 0 0>;
+ reg = <0x19>;
+ device_type = "ethernet-phy";
+ };
+ tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet4: ucc@2400 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ rx-clock-name = "none";
+ tx-clock-name = "clk13";
+ pio-handle = <&pio2>;
+ phy-handle = <&qe_phy1>;
+ phy-connection-type = "rmii";
+ };
+
+ serial2: ucc@2600 {
+ device_type = "serial";
+ compatible = "ucc_uart";
+ port-number = <0>;
+ rx-clock-name = "brg6";
+ tx-clock-name = "brg6";
+ pio-handle = <&pio3>;
+ };
+
+ serial3: ucc@2200 {
+ device_type = "serial";
+ compatible = "ucc_uart";
+ port-number = <1>;
+ rx-clock-name = "brg2";
+ tx-clock-name = "brg2";
+ pio-handle = <&pio4>;
+ };
+};
new file mode 100644
@@ -0,0 +1,94 @@
+/*
+ * P1025 TWR Device Tree Source (32-bit address map)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/p1021si-pre.dtsi"
+/ {
+ model = "fsl,P1025";
+ compatible = "fsl,TWR-P1025";
+
+ memory {
+ device_type = "memory";
+ };
+
+ lbc: localbus@ffe05000 {
+ reg = <0 0xffe05000 0 0x1000>;
+
+ /* NOR Flash */
+ ranges = <0x0 0x0 0x0 0xec000000 0x04000000>;
+ };
+
+ soc: soc@ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie@ffe09000 {
+ ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+ reg = <0 0xffe09000 0 0x1000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@ffe0a000 {
+ reg = <0 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ qe: qe@ffe80000 {
+ ranges = <0x0 0x0 0xffe80000 0x40000>;
+ reg = <0 0xffe80000 0 0x480>;
+ brg-frequency = <0>;
+ bus-frequency = <0>;
+ };
+};
+
+/include/ "p1025twr.dtsi"
+/include/ "fsl/p1021si-post.dtsi"
@@ -123,6 +123,12 @@ config P1023_RDS
help
This option enables support for the P1023 RDS and RDB boards
+config TWR_P102x
+ bool "Freescale TWR-P102x"
+ select DEFAULT_UIMAGE
+ help
+ This option enables support for the TWR-P1025 board.
+
config SOCRATES
bool "Socrates"
select DEFAULT_UIMAGE
@@ -18,6 +18,7 @@ obj-$(CONFIG_P1010_RDB) += p1010rdb.o
obj-$(CONFIG_P1022_DS) += p1022_ds.o
obj-$(CONFIG_P1022_RDK) += p1022_rdk.o
obj-$(CONFIG_P1023_RDS) += p1023_rds.o
+obj-$(CONFIG_TWR_P102x) += twr_p102x.o
obj-$(CONFIG_P2041_RDB) += p2041_rdb.o corenet_ds.o
obj-$(CONFIG_P3041_DS) += p3041_ds.o corenet_ds.o
obj-$(CONFIG_P4080_DS) += p4080_ds.o corenet_ds.o
new file mode 100644
@@ -0,0 +1,147 @@
+/*
+ * Copyright 2010-2011, 2013 Freescale Semiconductor, Inc.
+ *
+ * Author: Michael Johnston <michael.johnston@freescale.com>
+ *
+ * Description:
+ * TWR-P102x Board Setup
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/pci.h>
+#include <linux/of_platform.h>
+
+#include <asm/pci-bridge.h>
+#include <asm/udbg.h>
+#include <asm/mpic.h>
+#include <asm/qe.h>
+#include <asm/qe_ic.h>
+#include <asm/fsl_guts.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+#include "smp.h"
+
+#include "mpc85xx.h"
+
+static void __init twr_p1025_pic_init(void)
+{
+ struct mpic *mpic;
+
+#ifdef CONFIG_QUICC_ENGINE
+ struct device_node *np;
+#endif
+
+ mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN |
+ MPIC_SINGLE_DEST_CPU,
+ 0, 256, " OpenPIC ");
+
+ BUG_ON(mpic == NULL);
+ mpic_init(mpic);
+
+#ifdef CONFIG_QUICC_ENGINE
+ np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
+ if (np) {
+ qe_ic_init(np, 0, qe_ic_cascade_low_mpic,
+ qe_ic_cascade_high_mpic);
+ of_node_put(np);
+ } else
+ pr_err("Could not find qe-ic node\n");
+#endif
+}
+
+/* ************************************************************************
+ *
+ * Setup the architecture
+ *
+ */
+static void __init twr_p1025_setup_arch(void)
+{
+#ifdef CONFIG_QUICC_ENGINE
+ struct device_node *np;
+#endif
+
+ if (ppc_md.progress)
+ ppc_md.progress("twr_p1025_setup_arch()", 0);
+
+ mpc85xx_smp_init();
+
+ fsl_pci_assign_primary();
+
+#ifdef CONFIG_QUICC_ENGINE
+ mpc85xx_qe_init();
+
+#if defined(CONFIG_UCC_GETH) || defined(CONFIG_SERIAL_QE)
+ if (machine_is(twr_p1025)) {
+ struct ccsr_guts __iomem *guts;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,p1021-guts");
+ if (np) {
+ guts = of_iomap(np, 0);
+ if (!guts)
+ pr_err("twr_p1025: could not map global utilities register\n");
+ else {
+ /* P1025 has pins muxed for QE and other functions. To
+ * enable QE UEC mode, we need to set bit QE0 for UCC1
+ * in Eth mode, QE0 and QE3 for UCC5 in Eth mode, QE9
+ * and QE12 for QE MII management signals in PMUXCR
+ * register.
+ * Set QE mux bits in PMUXCR */
+ setbits32(&guts->pmuxcr, MPC85xx_PMUXCR_QE(0) |
+ MPC85xx_PMUXCR_QE(3) |
+ MPC85xx_PMUXCR_QE(9) |
+ MPC85xx_PMUXCR_QE(12));
+ iounmap(guts);
+
+#if defined(CONFIG_SERIAL_QE)
+ /* On P1025TWR board, the UCC7 acted as UART port.
+ * However, The UCC7's CTS pin is low level in default,
+ * it will impact the transmission in full duplex
+ * communication. So disable the Flow control pin PA18.
+ * The UCC7 UART just can use RXD and TXD pins.
+ */
+ par_io_config_pin(0, 18, 0, 0, 0, 0);
+#endif
+ /* Drive PB29 to CPLD low - CPLD will then change
+ * muxing from LBC to QE */
+ par_io_config_pin(1, 29, 1, 0, 0, 0);
+ par_io_data_set(1, 29, 0);
+ }
+ of_node_put(np);
+ }
+ }
+#endif
+#endif /* CONFIG_QUICC_ENGINE */
+
+ printk(KERN_INFO "TWR-P1025 board from Freescale Semiconductor\n");
+}
+
+machine_arch_initcall(twr_p1025, mpc85xx_common_publish_devices);
+
+static int __init twr_p1025_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ return of_flat_dt_is_compatible(root, "fsl,TWR-P1025");
+}
+
+define_machine(twr_p1025) {
+ .name = "TWR-P1025",
+ .probe = twr_p1025_probe,
+ .setup_arch = twr_p1025_setup_arch,
+ .init_IRQ = twr_p1025_pic_init,
+#ifdef CONFIG_PCI
+ .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
+#endif
+ .get_irq = mpic_get_irq,
+ .restart = fsl_rstcr_restart,
+ .calibrate_decr = generic_calibrate_decr,
+ .progress = udbg_progress,
+};