@@ -83,12 +83,21 @@ void board_init_r(gd_t *gd, ulong dest_addr)
mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
CONFIG_SPL_RELOC_MALLOC_SIZE);
+#ifndef CONFIG_SPL_NAND_BOOT
env_init();
+#endif
#ifdef CONFIG_SPL_MMC_BOOT
mmc_initialize(bd);
#endif
/* relocate environment function pointers etc. */
+#ifdef CONFIG_SPL_NAND_BOOT
+ nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+ gd->env_addr = (ulong)(CONFIG_ENV_ADDR);
+ gd->env_valid = 1;
+#else
env_relocate();
+#endif
#ifdef CONFIG_SYS_I2C
i2c_init_all();
@@ -97,11 +106,17 @@ void board_init_r(gd_t *gd, ulong dest_addr)
#endif
gd->ram_size = initdram(0);
+#ifdef CONFIG_SPL_NAND_BOOT
+ puts("Tertiary program loader running in sram...");
+#else
puts("Second program loader running in sram...\n");
+#endif
#ifdef CONFIG_SPL_MMC_BOOT
mmc_boot();
#elif defined(CONFIG_SPL_SPI_BOOT)
spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ nand_boot();
#endif
}
@@ -15,59 +15,14 @@
DECLARE_GLOBAL_DATA_PTR;
-#ifndef CONFIG_SYS_INIT_L2_ADDR
-/*
- * Fixed sdram init -- doesn't use serial presence detect.
- */
-static void sdram_init(void)
-{
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
-
- __raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds);
- __raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config);
-#if CONFIG_CHIP_SELECTS_PER_CTRL > 1
- __raw_writel(CONFIG_SYS_DDR_CS1_BNDS, &ddr->cs1_bnds);
- __raw_writel(CONFIG_SYS_DDR_CS1_CONFIG, &ddr->cs1_config);
-#endif
- __raw_writel(CONFIG_SYS_DDR_TIMING_3, &ddr->timing_cfg_3);
- __raw_writel(CONFIG_SYS_DDR_TIMING_0, &ddr->timing_cfg_0);
- __raw_writel(CONFIG_SYS_DDR_TIMING_1, &ddr->timing_cfg_1);
- __raw_writel(CONFIG_SYS_DDR_TIMING_2, &ddr->timing_cfg_2);
-
- __raw_writel(CONFIG_SYS_DDR_CONTROL_2, &ddr->sdram_cfg_2);
- __raw_writel(CONFIG_SYS_DDR_MODE_1, &ddr->sdram_mode);
- __raw_writel(CONFIG_SYS_DDR_MODE_2, &ddr->sdram_mode_2);
-
- __raw_writel(CONFIG_SYS_DDR_INTERVAL, &ddr->sdram_interval);
- __raw_writel(CONFIG_SYS_DDR_DATA_INIT, &ddr->sdram_data_init);
- __raw_writel(CONFIG_SYS_DDR_CLK_CTRL, &ddr->sdram_clk_cntl);
-
- __raw_writel(CONFIG_SYS_DDR_TIMING_4, &ddr->timing_cfg_4);
- __raw_writel(CONFIG_SYS_DDR_TIMING_5, &ddr->timing_cfg_5);
- __raw_writel(CONFIG_SYS_DDR_ZQ_CONTROL, &ddr->ddr_zq_cntl);
- __raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL, &ddr->ddr_wrlvl_cntl);
-
- /* Set, but do not enable the memory */
- __raw_writel(CONFIG_SYS_DDR_CONTROL & ~SDRAM_CFG_MEM_EN, &ddr->sdram_cfg);
-
- asm volatile("sync;isync");
- udelay(500);
-
- /* Let the controller go */
- out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN);
-
- set_next_law(0, CONFIG_SYS_SDRAM_SIZE_LAW, LAW_TRGT_IF_DDR_1);
-}
-#endif
-
void board_init_f(ulong bootflag)
{
u32 plat_ratio;
ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
-#ifndef CONFIG_QE
- ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
-#elif defined(CONFIG_P1021RDB)
- par_io_t *par_io = (par_io_t *)&(gur->qe_par_io);
+
+#if defined(CONFIG_SYS_NAND_BR_PRELIM) && defined(CONFIG_SYS_NAND_OR_PRELIM)
+ set_lbc_br(0, CONFIG_SYS_NAND_BR_PRELIM);
+ set_lbc_or(0, CONFIG_SYS_NAND_OR_PRELIM);
#endif
/* initialize selected port with appropriate baud rate */
@@ -80,35 +35,6 @@ void board_init_f(ulong bootflag)
puts("\nNAND boot... ");
-#ifndef CONFIG_QE
- /* init DDR3 reset signal */
- __raw_writel(0x02000000, &pgpio->gpdir);
- __raw_writel(0x00200000, &pgpio->gpodr);
- __raw_writel(0x00000000, &pgpio->gpdat);
- udelay(1000);
- __raw_writel(0x00200000, &pgpio->gpdat);
- udelay(1000);
- __raw_writel(0x00000000, &pgpio->gpdir);
-#elif defined(CONFIG_P1021RDB)
- /* init DDR3 reset signal CE_PB8 */
- out_be32(&par_io[1].cpdir1, 0x00004000);
- out_be32(&par_io[1].cpodr, 0x00800000);
- out_be32(&par_io[1].cppar1, 0x00000000);
- /* reset DDR3 */
- out_be32(&par_io[1].cpdat, 0x00800000);
- udelay(1000);
- out_be32(&par_io[1].cpdat, 0x00000000);
- udelay(1000);
- out_be32(&par_io[1].cpdat, 0x00800000);
- /* disable the CE_PB8 */
- out_be32(&par_io[1].cpdir1, 0x00000000);
-#endif
-
-#ifndef CONFIG_SYS_INIT_L2_ADDR
- /* Initialize the DDR3 */
- sdram_init();
-#endif
-
/* copy code to RAM and jump to it - this should not return */
/* NOTE - code has to be copied out of NAND buffer before
* other blocks can be read.
@@ -118,6 +44,7 @@ void board_init_f(ulong bootflag)
void board_init_r(gd_t *gd, ulong dest_addr)
{
+ puts("\nSecond program loader running in sram...");
nand_boot();
}
@@ -98,7 +98,13 @@ struct fsl_e_tlb_entry tlb_table[] = {
/* *I*G - L2SRAM */
SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
- 0, 11, BOOKE_PAGESZ_256K, 1)
+ 0, 11, BOOKE_PAGESZ_256K, 1),
+#if CONFIG_SYS_L2_SIZE >= (256 << 10)
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000,
+ CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 12, BOOKE_PAGESZ_256K, 1)
+#endif
#endif
};
@@ -205,36 +205,45 @@
#ifdef CONFIG_NAND
#define CONFIG_SPL
+#define CONFIG_TPL
+#ifdef CONFIG_TPL_BUILD
+#define CONFIG_SPL_NAND_BOOT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_NAND_INIT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SPL_MAX_SIZE (128 << 10)
+#define CONFIG_SPL_TEXT_BASE 0xf8f81000
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (576 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000)
+#define CONFIG_SYS_NAND_U_BOOT_START (0x11000000)
+#define CONFIG_SYS_NAND_U_BOOT_OFFS ((128 + 128) << 10)
+#elif defined(CONFIG_SPL_BUILD)
#define CONFIG_SPL_INIT_MINIMAL
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-
-#define CONFIG_SPL_TEXT_BASE 0xfffff000
+#define CONFIG_SPL_TEXT_BASE 0xff800000
#define CONFIG_SPL_MAX_SIZE 4096
-
-#ifdef CONFIG_SYS_INIT_L2_ADDR
-/* We multiply CONFIG_SPL_MAX_SIZE by two to leave some room for BSS. */
-#define CONFIG_SYS_TEXT_BASE 0xf8f82000
-#define CONFIG_SPL_RELOC_TEXT_BASE \
- (CONFIG_SYS_INIT_L2_END - CONFIG_SPL_MAX_SIZE * 2)
-#define CONFIG_SPL_RELOC_STACK \
- (CONFIG_SYS_INIT_L2_END - CONFIG_SPL_MAX_SIZE * 2)
-#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR)
-#define CONFIG_SYS_NAND_U_BOOT_START \
- (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SPL_MAX_SIZE)
-#else
-#define CONFIG_SYS_TEXT_BASE 0x00201000
-#define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000
-#define CONFIG_SPL_RELOC_STACK 0x00100000
-#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE)
-#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
-#endif
-
-#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000)
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0
-#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (128 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST 0xf8f80000
+#define CONFIG_SYS_NAND_U_BOOT_START 0xf8f80000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (128 << 10)
+#endif /* not CONFIG_TPL_BUILD */
+
+#define CONFIG_SPL_PAD_TO 0x20000
+#define CONFIG_TPL_PAD_TO 0x20000
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SYS_TEXT_BASE 0x11001000
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
#endif
#ifndef CONFIG_SYS_TEXT_BASE
@@ -576,6 +585,23 @@
#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 160 * 1024)
#define CONFIG_SPL_RELOC_MALLOC_SIZE (96 << 10)
#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 112 * 1024)
+#elif defined(CONFIG_NAND)
+#ifdef CONFIG_TPL_BUILD
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
+#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
+#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000
+#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 192 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 208 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE (48 << 10)
+#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 176 * 1024)
+#else
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
+#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
+#define CONFIG_SPL_RELOC_TEXT_BASE (CONFIG_SYS_INIT_L2_END - 0x2000)
+#define CONFIG_SPL_RELOC_STACK ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)
+#endif /* CONFIG_TPL_BUILD */
#endif
#endif
@@ -801,9 +827,14 @@
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_SYS_MMC_ENV_DEV 0
#elif defined(CONFIG_NAND)
-#define CONFIG_ENV_IS_IN_NAND
+#ifdef CONFIG_TPL_BUILD
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10))
+#else
#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
+#endif
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET (1024 * 1024)
#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
#elif defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */