diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index b8727d5..cacfbf4 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -927,6 +927,16 @@ config NET_NETX
 	  To compile this driver as a module, choose M here. The module
 	  will be called netx-eth.
 
+config TI_DAVINCI_EMAC
+	tristate "TI DaVinci EMAC Support"
+	depends on ARM && ARCH_DAVINCI
+	select PHYLIB
+	help
+	  This driver supports TI's DaVinci Ethernet .
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called davinci_emac_driver.  This is recommended.
+
 config DM9000
 	tristate "DM9000 support"
 	depends on ARM || BLACKFIN || MIPS
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index dcd5f15..34f1253 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -2,6 +2,9 @@
 # Makefile for the Linux network (ethercard) device drivers.
 #
 
+davinci_emac_driver-objs := davinci_emac.o
+obj-$(CONFIG_TI_DAVINCI_EMAC) += davinci_emac_driver.o
+
 obj-$(CONFIG_E1000) += e1000/
 obj-$(CONFIG_E1000E) += e1000e/
 obj-$(CONFIG_IBM_NEW_EMAC) += ibm_newemac/
diff --git a/drivers/net/davinci_emac.c b/drivers/net/davinci_emac.c
new file mode 100644
index 0000000..cf689a0
--- /dev/null
+++ b/drivers/net/davinci_emac.c
@@ -0,0 +1,2832 @@
+/*
+ * DaVinci Ethernet Medium Access Controller
+ *
+ * DaVinci EMAC is based upon CPPI 3.0 TI DMA engine
+ *
+ * Copyright (C) 2009 Texas Instruments.
+ *
+ * ---------------------------------------------------------------------------
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ * ---------------------------------------------------------------------------
+ * History:
+ * 0-5 A number of folks worked on this driver in bits and pieces but the major
+ *     contribution came from Suraj Iyer and Anant Gole
+ * 6.0 Anant Gole - rewrote the driver as per Linux conventions
+ * 6.1 Chaithrika U S - added support for Gigabit and RMII features,
+ *     PHY layer usage
+ */
+
+/** Pending Items in this driver:
+ * 1. Use Linux cache infrastcture for DMA'ed memory (dma_xxx functions)
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/string.h>
+#include <linux/timer.h>
+#include <linux/errno.h>
+#include <linux/in.h>
+#include <linux/ioport.h>
+#include <linux/slab.h>
+#include <linux/mm.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/ethtool.h>
+#include <linux/highmem.h>
+#include <linux/proc_fs.h>
+#include <linux/ctype.h>
+#include <linux/version.h>
+#include <linux/spinlock.h>
+#include <linux/dma-mapping.h>
+#include <linux/clk.h>
+#include <linux/platform_device.h>
+#include <linux/semaphore.h>
+#include <linux/phy.h>
+#include <linux/bitops.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
+
+#include <asm/irq.h>
+#include <asm/page.h>
+
+#include <mach/emac.h>
+
+static int debug_level;
+module_param(debug_level, int, 0);
+MODULE_PARM_DESC(debug_level, "DaVinci EMAC debug level (NETIF_MSG bits)");
+
+/* Netif debug messages possible */
+#define DAVINCI_EMAC_DEBUG	(NETIF_MSG_DRV | \
+				NETIF_MSG_PROBE | \
+				NETIF_MSG_LINK | \
+				NETIF_MSG_TIMER | \
+				NETIF_MSG_IFDOWN | \
+				NETIF_MSG_IFUP | \
+				NETIF_MSG_RX_ERR | \
+				NETIF_MSG_TX_ERR | \
+				NETIF_MSG_TX_QUEUED | \
+				NETIF_MSG_INTR | \
+				NETIF_MSG_TX_DONE | \
+				NETIF_MSG_RX_STATUS | \
+				NETIF_MSG_PKTDATA | \
+				NETIF_MSG_HW | \
+				NETIF_MSG_WOL)
+
+/* version info */
+#define EMAC_MAJOR_VERSION	6
+#define EMAC_MINOR_VERSION	1
+#define EMAC_MODULE_VERSION	"6.1"
+MODULE_VERSION(EMAC_MODULE_VERSION);
+static const char emac_version_string[] = "TI DaVinci EMAC Linux v6.1";
+
+/* Configuration items */
+#define EMAC_DEF_PASS_CRC		(0) /* Do not pass CRC upto frames */
+#define EMAC_DEF_QOS_EN			(0) /* EMAC proprietary QoS disabled */
+#define EMAC_DEF_NO_BUFF_CHAIN		(0) /* No buffer chain */
+#define EMAC_DEF_MACCTRL_FRAME_EN	(0) /* Discard Maccontrol frames */
+#define EMAC_DEF_SHORT_FRAME_EN		(0) /* Discard short frames */
+#define EMAC_DEF_ERROR_FRAME_EN		(0) /* Discard error frames */
+#define EMAC_DEF_PROM_EN		(0) /* Promiscous disabled */
+#define EMAC_DEF_PROM_CH		(0) /* Promiscous channel is 0 */
+#define EMAC_DEF_BCAST_EN		(1) /* Broadcast enabled */
+#define EMAC_DEF_BCAST_CH		(0) /* Broadcast channel is 0 */
+#define EMAC_DEF_MCAST_EN		(1) /* Multicast enabled */
+#define EMAC_DEF_MCAST_CH		(0) /* Multicast channel is 0 */
+
+#define EMAC_DEF_TXPRIO_FIXED		(1) /* TX Priority is fixed */
+#define EMAC_DEF_TXPACING_EN		(0) /* TX pacing NOT supported*/
+
+#define EMAC_DEF_BUFFER_OFFSET		(0) /* Buffer offset to DMA (future) */
+#define EMAC_DEF_MIN_ETHPKTSIZE		(60) /* Minimum ethernet pkt size */
+#define EMAC_DEF_MAX_FRAME_SIZE		(1500 + 14 + 4 + 4)
+#define EMAC_DEF_TX_CH			(0) /* Default 0th channel */
+#define EMAC_DEF_RX_CH			(0) /* Default 0th channel */
+#define EMAC_DEF_MDIO_TICK_MS		(10) /* typically 1 tick=1 ms) */
+#define EMAC_DEF_MAX_TX_CH		(1) /* Max TX channels configured */
+#define EMAC_DEF_MAX_RX_CH		(1) /* Max RX channels configured */
+#define EMAC_POLL_WEIGHT		(64) /* Default NAPI poll weight */
+
+/* Buffer descriptor parameters */
+#define EMAC_DEF_TX_MAX_SERVICE		(32) /* TX max service BD's */
+#define EMAC_DEF_RX_MAX_SERVICE		(64) /* should = netdev->weight */
+
+/* EMAC register related defines */
+#define EMAC_ALL_MULTI_REG_VALUE	(0xFFFFFFFF)
+#define EMAC_NUM_MULTICAST_BITS		(64)
+#define EMAC_TEARDOWN_VALUE		(0xFFFFFFFC)
+#define EMAC_TX_CONTROL_TX_ENABLE_VAL	(0x1)
+#define EMAC_RX_CONTROL_RX_ENABLE_VAL	(0x1)
+#define EMAC_MAC_HOST_ERR_INTMASK_VAL	(0x2)
+#define EMAC_RX_UNICAST_CLEAR_ALL	(0xFF)
+#define EMAC_INT_MASK_CLEAR		(0xFF)
+
+/* RX MBP register bit positions */
+#define EMAC_RXMBP_PASSCRC_MASK		BIT(30)
+#define EMAC_RXMBP_QOSEN_MASK		BIT(29)
+#define EMAC_RXMBP_NOCHAIN_MASK		BIT(28)
+#define EMAC_RXMBP_CMFEN_MASK		BIT(24)
+#define EMAC_RXMBP_CSFEN_MASK		BIT(23)
+#define EMAC_RXMBP_CEFEN_MASK		BIT(22)
+#define EMAC_RXMBP_CAFEN_MASK		BIT(21)
+#define EMAC_RXMBP_PROMCH_SHIFT		(16)
+#define EMAC_RXMBP_PROMCH_MASK		(0x7 << 16)
+#define EMAC_RXMBP_BROADEN_MASK		BIT(13)
+#define EMAC_RXMBP_BROADCH_SHIFT	(8)
+#define EMAC_RXMBP_BROADCH_MASK		(0x7 << 8)
+#define EMAC_RXMBP_MULTIEN_MASK		BIT(5)
+#define EMAC_RXMBP_MULTICH_SHIFT	(0)
+#define EMAC_RXMBP_MULTICH_MASK		(0x7)
+#define EMAC_RXMBP_CHMASK		(0x7)
+
+/* EMAC register definitions/bit maps used */
+# define EMAC_MBP_RXPROMISC		(0x00200000)
+# define EMAC_MBP_PROMISCCH(ch)		(((ch) & 0x7) << 16)
+# define EMAC_MBP_RXBCAST		(0x00002000)
+# define EMAC_MBP_BCASTCHAN(ch)		(((ch) & 0x7) << 8)
+# define EMAC_MBP_RXMCAST		(0x00000020)
+# define EMAC_MBP_MCASTCHAN(ch)		((ch) & 0x7)
+
+/* EMAC mac_control register */
+#define EMAC_MACCONTROL_TXPTYPE		(0x200)
+#define EMAC_MACCONTROL_TXPACEEN	(0x40)
+#define EMAC_MACCONTROL_MIIEN		(0x20)
+#define EMAC_MACCONTROL_GIGABITEN	(0x80)
+#define EMAC_MACCONTROL_GIGABITEN_SHIFT (7)
+#define EMAC_MACCONTROL_FULLDUPLEXEN	(0x1)
+#define EMAC_MACCONTROL_RMIISPEED_MASK	BIT(15)
+
+/* GIGABIT MODE related bits */
+#define EMAC_DM646X_MACCONTORL_GMIIEN	BIT(5)
+#define EMAC_DM646X_MACCONTORL_GIG	BIT(7)
+#define EMAC_DM646X_MACCONTORL_GIGFORCE	BIT(17)
+
+/* EMAC mac_status register */
+#define EMAC_MACSTATUS_TXERRCODE_MASK	(0xF00000)
+#define EMAC_MACSTATUS_TXERRCODE_SHIFT	(20)
+#define EMAC_MACSTATUS_TXERRCH_MASK	(0x7)
+#define EMAC_MACSTATUS_TXERRCH_SHIFT	(16)
+#define EMAC_MACSTATUS_RXERRCODE_MASK	(0xF000)
+#define EMAC_MACSTATUS_RXERRCODE_SHIFT	(12)
+#define EMAC_MACSTATUS_RXERRCH_MASK	(0x7)
+#define EMAC_MACSTATUS_RXERRCH_SHIFT	(8)
+
+/* EMAC RX register masks */
+#define EMAC_RX_MAX_LEN_MASK		(0xFFFF)
+#define EMAC_RX_BUFFER_OFFSET_MASK	(0xFFFF)
+
+/* MAC_IN_VECTOR (0x180) register bit fields */
+#define EMAC_DM644X_MAC_IN_VECTOR_HOST_INT	      (0x20000)
+#define EMAC_DM644X_MAC_IN_VECTOR_STATPEND_INT	      (0x10000)
+#define EMAC_DM644X_MAC_IN_VECTOR_RX_INT_VEC	      (0x0100)
+#define EMAC_DM644X_MAC_IN_VECTOR_TX_INT_VEC	      (0x01)
+
+/** NOTE:: For DM646x the IN_VECTOR has changed */
+#define EMAC_DM646X_MAC_IN_VECTOR_RX_INT_VEC	BIT(EMAC_DEF_RX_CH)
+#define EMAC_DM646X_MAC_IN_VECTOR_TX_INT_VEC	BIT(16 + EMAC_DEF_TX_CH)
+
+/* CPPI bit positions */
+#define EMAC_CPPI_SOP_BIT		BIT(31)
+#define EMAC_CPPI_EOP_BIT		BIT(30)
+#define EMAC_CPPI_OWNERSHIP_BIT		BIT(29)
+#define EMAC_CPPI_EOQ_BIT		BIT(28)
+#define EMAC_CPPI_TEARDOWN_COMPLETE_BIT BIT(27)
+#define EMAC_CPPI_PASS_CRC_BIT		BIT(26)
+#define EMAC_RX_BD_BUF_SIZE		(0xFFFF)
+#define EMAC_BD_LENGTH_FOR_CACHE	(16) /* only CPPI bytes */
+#define EMAC_RX_BD_PKT_LENGTH_MASK	(0xFFFF)
+
+/* Max hardware defines */
+#define EMAC_MAX_TXRX_CHANNELS		 (8)  /* Max hardware channels */
+#define EMAC_DEF_MAX_MULTICAST_ADDRESSES (64) /* Max mcast addr's */
+
+/* EMAC Peripheral Device Register Memory Layout structure */
+#define EMAC_TXIDVER		0x0
+#define EMAC_TXCONTROL		0x4
+#define EMAC_TXTEARDOWN		0x8
+#define EMAC_RXIDVER		0x10
+#define EMAC_RXCONTROL		0x14
+#define EMAC_RXTEARDOWN		0x18
+#define EMAC_TXINTSTATRAW	0x80
+#define EMAC_TXINTSTATMASKED	0x84
+#define EMAC_TXINTMASKSET	0x88
+#define EMAC_TXINTMASKCLEAR	0x8C
+#define EMAC_MACINVECTOR	0x90
+
+#define EMAC_DM646X_MACEOIVECTOR	0x94
+
+#define EMAC_RXINTSTATRAW	0xA0
+#define EMAC_RXINTSTATMASKED	0xA4
+#define EMAC_RXINTMASKSET	0xA8
+#define EMAC_RXINTMASKCLEAR	0xAC
+#define EMAC_MACINTSTATRAW	0xB0
+#define EMAC_MACINTSTATMASKED	0xB4
+#define EMAC_MACINTMASKSET	0xB8
+#define EMAC_MACINTMASKCLEAR	0xBC
+
+#define EMAC_RXMBPENABLE	0x100
+#define EMAC_RXUNICASTSET	0x104
+#define EMAC_RXUNICASTCLEAR	0x108
+#define EMAC_RXMAXLEN		0x10C
+#define EMAC_RXBUFFEROFFSET	0x110
+#define EMAC_RXFILTERLOWTHRESH	0x114
+
+#define EMAC_MACCONTROL		0x160
+#define EMAC_MACSTATUS		0x164
+#define EMAC_EMCONTROL		0x168
+#define EMAC_FIFOCONTROL	0x16C
+#define EMAC_MACCONFIG		0x170
+#define EMAC_SOFTRESET		0x174
+#define EMAC_MACSRCADDRLO	0x1D0
+#define EMAC_MACSRCADDRHI	0x1D4
+#define EMAC_MACHASH1		0x1D8
+#define EMAC_MACHASH2		0x1DC
+#define EMAC_MACADDRLO		0x500
+#define EMAC_MACADDRHI		0x504
+#define EMAC_MACINDEX		0x508
+
+/* EMAC HDP and Completion registors */
+#define EMAC_TXHDP(ch)		(0x600 + (ch * 4))
+#define EMAC_RXHDP(ch)		(0x620 + (ch * 4))
+#define EMAC_TXCP(ch)		(0x640 + (ch * 4))
+#define EMAC_RXCP(ch)		(0x660 + (ch * 4))
+
+/* EMAC statistics registers */
+#define EMAC_RXGOODFRAMES	0x200
+#define EMAC_RXBCASTFRAMES	0x204
+#define EMAC_RXMCASTFRAMES	0x208
+#define EMAC_RXPAUSEFRAMES	0x20C
+#define EMAC_RXCRCERRORS	0x210
+#define EMAC_RXALIGNCODEERRORS	0x214
+#define EMAC_RXOVERSIZED	0x218
+#define EMAC_RXJABBER		0x21C
+#define EMAC_RXUNDERSIZED	0x220
+#define EMAC_RXFRAGMENTS	0x224
+#define EMAC_RXFILTERED		0x228
+#define EMAC_RXQOSFILTERED	0x22C
+#define EMAC_RXOCTETS		0x230
+#define EMAC_TXGOODFRAMES	0x234
+#define EMAC_TXBCASTFRAMES	0x238
+#define EMAC_TXMCASTFRAMES	0x23C
+#define EMAC_TXPAUSEFRAMES	0x240
+#define EMAC_TXDEFERRED		0x244
+#define EMAC_TXCOLLISION	0x248
+#define EMAC_TXSINGLECOLL	0x24C
+#define EMAC_TXMULTICOLL	0x250
+#define EMAC_TXEXCESSIVECOLL	0x254
+#define EMAC_TXLATECOLL		0x258
+#define EMAC_TXUNDERRUN		0x25C
+#define EMAC_TXCARRIERSENSE	0x260
+#define EMAC_TXOCTETS		0x264
+#define EMAC_NETOCTETS		0x280
+#define EMAC_RXSOFOVERRUNS	0x284
+#define EMAC_RXMOFOVERRUNS	0x288
+#define EMAC_RXDMAOVERRUNS	0x28C
+
+/* EMAC DM644x control registers */
+#define EMAC_CTRL_EWCTL		(0x4)
+#define EMAC_CTRL_EWINTTCNT	(0x8)
+
+/* EMAC MDIO related */
+/* Mask & Control defines */
+#define MDIO_CONTROL_CLKDIV	(0xFF)
+#define MDIO_CONTROL_ENABLE	BIT(30)
+#define MDIO_USERACCESS_GO	BIT(31)
+#define MDIO_USERACCESS_WRITE	BIT(30)
+#define MDIO_USERACCESS_READ	(0)
+#define MDIO_USERACCESS_REGADR	(0x1F << 21)
+#define MDIO_USERACCESS_PHYADR	(0x1F << 16)
+#define MDIO_USERACCESS_DATA	(0xFFFF)
+#define MDIO_USERPHYSEL_LINKSEL	BIT(7)
+#define MDIO_VER_MODID		(0xFFFF << 16)
+#define MDIO_VER_REVMAJ		(0xFF   << 8)
+#define MDIO_VER_REVMIN		(0xFF)
+
+#define MDIO_USERACCESS(inst)	(0x80 + (inst * 8))
+#define MDIO_USERPHYSEL(inst)	(0x84 + (inst * 8))
+#define MDIO_CONTROL		(0x04)
+
+/* EMAC DM646X control module registers */
+#define EMAC_DM646X_CMRXINTEN	(0x14)
+#define EMAC_DM646X_CMTXINTEN	(0x18)
+
+/* EMAC EOI codes for C0 */
+#define EMAC_DM646X_MAC_EOI_C0_RXEN	(0x01)
+#define EMAC_DM646X_MAC_EOI_C0_TXEN	(0x02)
+
+/** net_buf_obj: EMAC network bufferdata structure
+ *
+ * EMAC network buffer data structure
+ */
+struct emac_netbufobj {
+	void *buf_token;
+	char *data_ptr;
+	int length;
+};
+
+/** net_pkt_obj: EMAC network packet data structure
+ *
+ * EMAC network packet data structure - supports buffer list (for future)
+ */
+struct emac_netpktobj {
+	void *pkt_token; /* data token may hold tx/rx chan id */
+	struct emac_netbufobj *buf_list; /* array of network buffer objects */
+	int num_bufs;
+	int pkt_length;
+};
+
+/** emac_tx_bd: EMAC TX Buffer descriptor data structure
+ *
+ * EMAC TX Buffer descriptor data structure
+ */
+struct emac_tx_bd {
+	int h_next;
+	int buff_ptr;
+	int off_b_len;
+	int mode; /* SOP, EOP, ownership, EOQ, teardown,Qstarv, length */
+	struct emac_tx_bd __iomem *next;
+	void *buf_token;
+};
+
+/** emac_txch: EMAC TX Channel data structure
+ *
+ * EMAC TX Channel data structure
+ */
+struct emac_txch {
+	/* Config related */
+	u32 num_bd;
+	u32 service_max;
+
+	/* CPPI specific */
+	u32 alloc_size;
+	void __iomem *bd_mem;
+	struct emac_tx_bd __iomem *bd_pool_head;
+	struct emac_tx_bd __iomem *active_queue_head;
+	struct emac_tx_bd __iomem *active_queue_tail;
+	struct emac_tx_bd __iomem *last_hw_bdprocessed;
+	u32 queue_active;
+	u32 teardown_pending;
+	u32 *tx_complete;
+
+	/** statistics */
+	u32 proc_count;     /* TX: # of times emac_tx_bdproc is called */
+	u32 mis_queued_packets;
+	u32 queue_reinit;
+	u32 end_of_queue_add;
+	u32 out_of_tx_bd;
+	u32 no_active_pkts; /* IRQ when there were no packets to process */
+	u32 active_queue_count;
+};
+
+/** emac_rx_bd: EMAC RX Buffer descriptor data structure
+ *
+ * EMAC RX Buffer descriptor data structure
+ */
+struct emac_rx_bd {
+	int h_next;
+	int buff_ptr;
+	int off_b_len;
+	int mode;
+	struct emac_rx_bd __iomem *next;
+	void *data_ptr;
+	void *buf_token;
+};
+
+/** emac_rxch: EMAC RX Channel data structure
+ *
+ * EMAC RX Channel data structure
+ */
+struct emac_rxch {
+	/* configuration info */
+	u32 num_bd;
+	u32 service_max;
+	u32 buf_size;
+	char mac_addr[6];
+
+	/** CPPI specific */
+	u32 alloc_size;
+	void __iomem *bd_mem;
+	struct emac_rx_bd __iomem *bd_pool_head;
+	struct emac_rx_bd __iomem *active_queue_head;
+	struct emac_rx_bd __iomem *active_queue_tail;
+	u32 queue_active;
+	u32 teardown_pending;
+
+	/* packet and buffer objects */
+	struct emac_netpktobj pkt_queue;
+	struct emac_netbufobj buf_queue;
+
+	/** statistics */
+	u32 proc_count; /* number of times emac_rx_bdproc is called */
+	u32 processed_bd;
+	u32 recycled_bd;
+	u32 out_of_rx_bd;
+	u32 out_of_rx_buffers;
+	u32 queue_reinit;
+	u32 end_of_queue_add;
+	u32 end_of_queue;
+	u32 mis_queued_packets;
+};
+
+/* emac_priv: EMAC private data structure
+ *
+ * EMAC adapter private data structure
+ */
+struct emac_priv {
+	u32 msg_enable;
+	struct net_device *ndev;
+	struct platform_device *pdev;
+	struct napi_struct napi;
+	char mac_addr[6];
+	spinlock_t tx_lock;
+	spinlock_t rx_lock;
+	void __iomem *remap_addr;
+	u32 emac_base_phys;
+	void __iomem *emac_base;
+	void __iomem *ctrl_base;
+	void __iomem *emac_ctrl_ram;
+	u32 ctrl_ram_size;
+	struct emac_txch *txch[EMAC_DEF_MAX_TX_CH];
+	struct emac_rxch *rxch[EMAC_DEF_MAX_RX_CH];
+	u32 link; /* 1=link on, 0=link off */
+	u32 speed; /* 0=Auto Neg, 1=No PHY, 10,100, 1000 - mbps */
+	u32 duplex; /* Link duplex: 0=Half, 1=Full */
+	u32 rx_buf_size;
+	u32 isr_count;
+	u8 rmii_en;
+	u8 version;
+	struct net_device_stats net_dev_stats;
+	u32 mac_hash1;
+	u32 mac_hash2;
+	u32 multicast_hash_cnt[EMAC_NUM_MULTICAST_BITS];
+	u32 rx_addr_type;
+	/* periodic timer required for MDIO polling */
+	struct timer_list periodic_timer;
+	u32 periodic_ticks;
+	u32 timer_active;
+	u32 phy_mask;
+	/* mii_bus,phy members */
+	struct mii_bus *mii_bus;
+	struct phy_device *phydev;
+	spinlock_t lock;
+};
+
+/* clock frequency for EMAC */
+static struct clk *emac_clk;
+static unsigned long emac_bus_frequency;
+static unsigned long mdio_max_freq;
+
+/* EMAC internal utility function */
+static inline u32 emac_virt_to_phys(void __iomem *addr)
+{
+	return (u32 __force) io_v2p(addr);
+}
+
+/* Cache macros - Packet buffers would be from skb pool which is cached */
+#define EMAC_VIRT_NOCACHE(addr) (addr)
+#define EMAC_CACHE_INVALIDATE(addr, size) \
+	dma_cache_maint((void *)addr, size, DMA_FROM_DEVICE)
+#define EMAC_CACHE_WRITEBACK(addr, size) \
+	dma_cache_maint((void *)addr, size, DMA_TO_DEVICE)
+#define EMAC_CACHE_WRITEBACK_INVALIDATE(addr, size) \
+	dma_cache_maint((void *)addr, size, DMA_BIDIRECTIONAL)
+
+/* DM644x does not have BD's in cached memory - so no cache functions */
+#define BD_CACHE_INVALIDATE(addr, size)
+#define BD_CACHE_WRITEBACK(addr, size)
+#define BD_CACHE_WRITEBACK_INVALIDATE(addr, size)
+
+/* EMAC TX Host Error description strings */
+static char *emac_txhost_errcodes[16] = {
+	"No error", "SOP error", "Ownership bit not set in SOP buffer",
+	"Zero Next Buffer Descriptor Pointer Without EOP",
+	"Zero Buffer Pointer", "Zero Buffer Length", "Packet Length Error",
+	"Reserved", "Reserved", "Reserved", "Reserved", "Reserved",
+	"Reserved", "Reserved", "Reserved", "Reserved"
+};
+
+/* EMAC RX Host Error description strings */
+static char *emac_rxhost_errcodes[16] = {
+	"No error", "Reserved", "Ownership bit not set in input buffer",
+	"Reserved", "Zero Buffer Pointer", "Reserved", "Reserved",
+	"Reserved", "Reserved", "Reserved", "Reserved", "Reserved",
+	"Reserved", "Reserved", "Reserved", "Reserved"
+};
+
+/* Helper macros */
+#define emac_read(reg)		  ioread32(priv->emac_base + (reg))
+#define emac_write(reg, val)      iowrite32(val, priv->emac_base + (reg))
+
+#define emac_ctrl_read(reg)	  ioread32((priv->ctrl_base + (reg)))
+#define emac_ctrl_write(reg, val) iowrite32(val, (priv->ctrl_base + (reg)))
+
+#define emac_mdio_read(reg)	  ioread32(bus->priv + (reg))
+#define emac_mdio_write(reg, val) iowrite32(val, (bus->priv + (reg)))
+
+/**
+ * emac_dump_regs: Dump important EMAC registers to debug terminal
+ * @priv: The DaVinci EMAC private adapter structure
+ *
+ * Executes ethtool set cmd & sets phy mode
+ *
+ */
+static void emac_dump_regs(struct emac_priv *priv)
+{
+	struct device *emac_dev = &priv->ndev->dev;
+
+	/* Print important registers in EMAC */
+	dev_info(emac_dev, "EMAC Basic registers\n");
+	dev_info(emac_dev, "EMAC: EWCTL: %08X, EWINTTCNT: %08X\n",
+		emac_ctrl_read(EMAC_CTRL_EWCTL),
+		emac_ctrl_read(EMAC_CTRL_EWINTTCNT));
+	dev_info(emac_dev, "EMAC: TXID: %08X %s, RXID: %08X %s\n",
+		emac_read(EMAC_TXIDVER),
+		((emac_read(EMAC_TXCONTROL)) ? "enabled" : "disabled"),
+		emac_read(EMAC_RXIDVER),
+		((emac_read(EMAC_RXCONTROL)) ? "enabled" : "disabled"));
+	dev_info(emac_dev, "EMAC: TXIntRaw:%08X, TxIntMasked: %08X, "\
+		"TxIntMasSet: %08X\n", emac_read(EMAC_TXINTSTATRAW),
+		emac_read(EMAC_TXINTSTATMASKED), emac_read(EMAC_TXINTMASKSET));
+	dev_info(emac_dev, "EMAC: RXIntRaw:%08X, RxIntMasked: %08X, "\
+		"RxIntMasSet: %08X\n", emac_read(EMAC_RXINTSTATRAW),
+		emac_read(EMAC_RXINTSTATMASKED), emac_read(EMAC_RXINTMASKSET));
+	dev_info(emac_dev, "EMAC: MacIntRaw:%08X, MacIntMasked: %08X, "\
+		"MacInVector=%08X\n", emac_read(EMAC_MACINTSTATRAW),
+		emac_read(EMAC_MACINTSTATMASKED), emac_read(EMAC_MACINVECTOR));
+	dev_info(emac_dev, "EMAC: EmuControl:%08X, FifoControl: %08X\n",
+		emac_read(EMAC_EMCONTROL), emac_read(EMAC_FIFOCONTROL));
+	dev_info(emac_dev, "EMAC: MBPEnable:%08X, RXUnicastSet: %08X, "\
+		"RXMaxLen=%08X\n", emac_read(EMAC_RXMBPENABLE),
+		emac_read(EMAC_RXUNICASTSET), emac_read(EMAC_RXMAXLEN));
+	dev_info(emac_dev, "EMAC: MacControl:%08X, MacStatus: %08X, "\
+		"MacConfig=%08X\n", emac_read(EMAC_MACCONTROL),
+		emac_read(EMAC_MACSTATUS), emac_read(EMAC_MACCONFIG));
+	dev_info(emac_dev, "EMAC: TXHDP[0]:%08X, RXHDP[0]: %08X\n",
+		emac_read(EMAC_TXHDP(0)), emac_read(EMAC_RXHDP(0)));
+	dev_info(emac_dev, "EMAC Statistics\n");
+	dev_info(emac_dev, "EMAC: rx_good_frames:%d\n",
+		emac_read(EMAC_RXGOODFRAMES));
+	dev_info(emac_dev, "EMAC: rx_broadcast_frames:%d\n",
+		emac_read(EMAC_RXBCASTFRAMES));
+	dev_info(emac_dev, "EMAC: rx_multicast_frames:%d\n",
+		emac_read(EMAC_RXMCASTFRAMES));
+	dev_info(emac_dev, "EMAC: rx_pause_frames:%d\n",
+		emac_read(EMAC_RXPAUSEFRAMES));
+	dev_info(emac_dev, "EMAC: rx_crcerrors:%d\n",
+		emac_read(EMAC_RXCRCERRORS));
+	dev_info(emac_dev, "EMAC: rx_align_code_errors:%d\n",
+		emac_read(EMAC_RXALIGNCODEERRORS));
+	dev_info(emac_dev, "EMAC: rx_oversized_frames:%d\n",
+		emac_read(EMAC_RXOVERSIZED));
+	dev_info(emac_dev, "EMAC: rx_jabber_frames:%d\n",
+		emac_read(EMAC_RXJABBER));
+	dev_info(emac_dev, "EMAC: rx_undersized_frames:%d\n",
+		emac_read(EMAC_RXUNDERSIZED));
+	dev_info(emac_dev, "EMAC: rx_fragments:%d\n",
+		emac_read(EMAC_RXFRAGMENTS));
+	dev_info(emac_dev, "EMAC: rx_filtered_frames:%d\n",
+		emac_read(EMAC_RXFILTERED));
+	dev_info(emac_dev, "EMAC: rx_qos_filtered_frames:%d\n",
+		emac_read(EMAC_RXQOSFILTERED));
+	dev_info(emac_dev, "EMAC: rx_octets:%d\n",
+		emac_read(EMAC_RXOCTETS));
+	dev_info(emac_dev, "EMAC: tx_goodframes:%d\n",
+		emac_read(EMAC_TXGOODFRAMES));
+	dev_info(emac_dev, "EMAC: tx_bcastframes:%d\n",
+		emac_read(EMAC_TXBCASTFRAMES));
+	dev_info(emac_dev, "EMAC: tx_mcastframes:%d\n",
+		emac_read(EMAC_TXMCASTFRAMES));
+	dev_info(emac_dev, "EMAC: tx_pause_frames:%d\n",
+		emac_read(EMAC_TXPAUSEFRAMES));
+	dev_info(emac_dev, "EMAC: tx_deferred_frames:%d\n",
+		emac_read(EMAC_TXDEFERRED));
+	dev_info(emac_dev, "EMAC: tx_collision_frames:%d\n",
+		emac_read(EMAC_TXCOLLISION));
+	dev_info(emac_dev, "EMAC: tx_single_coll_frames:%d\n",
+		emac_read(EMAC_TXSINGLECOLL));
+	dev_info(emac_dev, "EMAC: tx_mult_coll_frames:%d\n",
+		emac_read(EMAC_TXMULTICOLL));
+	dev_info(emac_dev, "EMAC: tx_excessive_collisions:%d\n",
+		emac_read(EMAC_TXEXCESSIVECOLL));
+	dev_info(emac_dev, "EMAC: tx_late_collisions:%d\n",
+		emac_read(EMAC_TXLATECOLL));
+	dev_info(emac_dev, "EMAC: tx_underrun:%d\n",
+		emac_read(EMAC_TXUNDERRUN));
+	dev_info(emac_dev, "EMAC: tx_carrier_sense_errors:%d\n",
+		emac_read(EMAC_TXCARRIERSENSE));
+	dev_info(emac_dev, "EMAC: tx_octets:%d\n",
+		emac_read(EMAC_TXOCTETS));
+	dev_info(emac_dev, "EMAC: net_octets:%d\n",
+		emac_read(EMAC_NETOCTETS));
+	dev_info(emac_dev, "EMAC: rx_sof_overruns:%d\n",
+		emac_read(EMAC_RXSOFOVERRUNS));
+	dev_info(emac_dev, "EMAC: rx_mof_overruns:%d\n",
+		emac_read(EMAC_RXMOFOVERRUNS));
+	dev_info(emac_dev, "EMAC: rx_dma_overruns:%d\n",
+		emac_read(EMAC_RXDMAOVERRUNS));
+}
+
+/*************************************************************************
+ *  EMAC MDIO/Phy Functionality
+ *************************************************************************/
+/**
+ * emac_get_drvinfo: Get EMAC driver information
+ * @ndev: The DaVinci EMAC network adapter
+ * @info: ethtool info structure containing name and version
+ *
+ * Returns EMAC driver information (name and version)
+ *
+ */
+static void emac_get_drvinfo(struct net_device *ndev,
+			     struct ethtool_drvinfo *info)
+{
+	strcpy(info->driver, emac_version_string);
+	strcpy(info->version, EMAC_MODULE_VERSION);
+}
+
+/**
+ * emac_get_settings: Get EMAC settings
+ * @ndev: The DaVinci EMAC network adapter
+ * @ecmd: ethtool command
+ *
+ * Executes ethool get command
+ *
+ */
+static int emac_get_settings(struct net_device *ndev,
+			     struct ethtool_cmd *ecmd)
+{
+	struct emac_priv *priv = netdev_priv(ndev);
+	if (priv->phy_mask)
+		return phy_ethtool_gset(priv->phydev, ecmd);
+	else
+		return -EOPNOTSUPP;
+
+}
+
+/**
+ * emac_set_settings: Set EMAC settings
+ * @ndev: The DaVinci EMAC network adapter
+ * @ecmd: ethtool command
+ *
+ * Executes ethool set command
+ *
+ */
+static int emac_set_settings(struct net_device *ndev, struct ethtool_cmd *ecmd)
+{
+	struct emac_priv *priv = netdev_priv(ndev);
+	if (priv->phy_mask)
+		return phy_ethtool_sset(priv->phydev, ecmd);
+	else
+		return -EOPNOTSUPP;
+
+}
+
+/**
+ * ethtool_ops: DaVinci EMAC Ethtool structure
+ *
+ * Ethtool support for EMAC adapter
+ *
+ */
+static const struct ethtool_ops ethtool_ops = {
+	.get_drvinfo = emac_get_drvinfo,
+	.get_settings = emac_get_settings,
+	.set_settings = emac_set_settings,
+	.get_link = ethtool_op_get_link,
+};
+
+/**
+ * emac_update_phystatus: Update Phy status
+ * @priv: The DaVinci EMAC private adapter structure
+ *
+ * Updates phy status and takes action for network queue if required
+ * based upon link status
+ *
+ */
+static void emac_update_phystatus(struct emac_priv *priv)
+{
+	u32 mac_control;
+	u32 new_duplex;
+	u32 cur_duplex;
+	struct net_device *ndev = priv->ndev;
+
+	mac_control = emac_read(EMAC_MACCONTROL);
+	cur_duplex = (mac_control & EMAC_MACCONTROL_FULLDUPLEXEN) ?
+			DUPLEX_FULL : DUPLEX_HALF;
+	if (priv->phy_mask)
+		new_duplex = priv->phydev->duplex;
+	else
+		new_duplex = DUPLEX_FULL;
+
+	/* We get called only if link has changed (speed/duplex/status) */
+	if ((priv->link) && (new_duplex != cur_duplex)) {
+		priv->duplex = new_duplex;
+		if (DUPLEX_FULL == priv->duplex)
+			mac_control |= (EMAC_MACCONTROL_FULLDUPLEXEN);
+		else
+			mac_control &= ~(EMAC_MACCONTROL_FULLDUPLEXEN);
+	}
+
+	if (priv->speed == SPEED_1000 && (priv->version == EMAC_VERSION_2)) {
+		mac_control = emac_read(EMAC_MACCONTROL);
+		mac_control |= (EMAC_DM646X_MACCONTORL_GMIIEN |
+				EMAC_DM646X_MACCONTORL_GIG |
+				EMAC_DM646X_MACCONTORL_GIGFORCE);
+	} else {
+		/* Clear the GIG bit and GIGFORCE bit */
+		mac_control &= ~(EMAC_DM646X_MACCONTORL_GIGFORCE |
+					EMAC_DM646X_MACCONTORL_GIG);
+
+		if (priv->rmii_en && (priv->speed == SPEED_100))
+			mac_control |= EMAC_MACCONTROL_RMIISPEED_MASK;
+		else
+			mac_control &= ~EMAC_MACCONTROL_RMIISPEED_MASK;
+	}
+
+	/* Update mac_control if changed */
+	emac_write(EMAC_MACCONTROL, mac_control);
+
+	if (priv->link) {
+		/* link ON */
+		if (!netif_carrier_ok(ndev))
+			netif_carrier_on(ndev);
+	/* reactivate the transmit queue if it is stopped */
+		if (netif_running(ndev) && netif_queue_stopped(ndev))
+			netif_wake_queue(ndev);
+	} else {
+		/* link OFF */
+		if (netif_carrier_ok(ndev))
+			netif_carrier_off(ndev);
+		if (!netif_queue_stopped(ndev))
+			netif_stop_queue(ndev);
+	}
+}
+
+/**
+ * hash_get: Calculate hash value from mac address
+ * @addr: mac address to delete from hash table
+ *
+ * Calculates hash value from mac address
+ *
+ */
+static u32 hash_get(u8 *addr)
+{
+	u32 hash;
+	u8 tmpval;
+	int cnt;
+	hash = 0;
+
+	for (cnt = 0; cnt < 2; cnt++) {
+		tmpval = *addr++;
+		hash ^= (tmpval >> 2) ^ (tmpval << 4);
+		tmpval = *addr++;
+		hash ^= (tmpval >> 4) ^ (tmpval << 2);
+		tmpval = *addr++;
+		hash ^= (tmpval >> 6) ^ (tmpval);
+	}
+
+	return hash & 0x3F;
+}
+
+/**
+ * hash_add: Hash function to add mac addr from hash table
+ * @priv: The DaVinci EMAC private adapter structure
+ * mac_addr: mac address to delete from hash table
+ *
+ * Adds mac address to the internal hash table
+ *
+ */
+static int hash_add(struct emac_priv *priv, u8 *mac_addr)
+{
+	struct device *emac_dev = &priv->ndev->dev;
+	u32 rc = 0;
+	u32 hash_bit;
+	u32 hash_value = hash_get(mac_addr);
+
+	if (hash_value >= EMAC_NUM_MULTICAST_BITS) {
+		if (netif_msg_drv(priv)) {
+			dev_err(emac_dev, "DaVinci EMAC: hash_add(): Invalid "\
+				"Hash %08x, should not be greater than %08x",
+				hash_value, (EMAC_NUM_MULTICAST_BITS - 1));
+		}
+		return -1;
+	}
+
+	/* set the hash bit only if not previously set */
+	if (priv->multicast_hash_cnt[hash_value] == 0) {
+		rc = 1; /* hash value changed */
+		if (hash_value < 32) {
+			hash_bit = BIT(hash_value);
+			priv->mac_hash1 |= hash_bit;
+		} else {
+			hash_bit = BIT((hash_value - 32));
+			priv->mac_hash2 |= hash_bit;
+		}
+	}
+
+	/* incr counter for num of mcast addr's mapped to "this" hash bit */
+	++priv->multicast_hash_cnt[hash_value];
+
+	return rc;
+}
+
+/**
+ * hash_del: Hash function to delete mac addr from hash table
+ * @priv: The DaVinci EMAC private adapter structure
+ * mac_addr: mac address to delete from hash table
+ *
+ * Removes mac address from the internal hash table
+ *
+ */
+static int hash_del(struct emac_priv *priv, u8 *mac_addr)
+{
+	u32 hash_value;
+	u32 hash_bit;
+
+	hash_value = hash_get(mac_addr);
+	if (priv->multicast_hash_cnt[hash_value] > 0) {
+		/* dec cntr for num of mcast addr's mapped to this hash bit */
+		--priv->multicast_hash_cnt[hash_value];
+	}
+
+	/* if counter still > 0, at least one multicast address refers
+	 * to this hash bit. so return 0 */
+	if (priv->multicast_hash_cnt[hash_value] > 0)
+		return 0;
+
+	if (hash_value < 32) {
+		hash_bit = BIT(hash_value);
+		priv->mac_hash1 &= ~hash_bit;
+	} else {
+		hash_bit = BIT((hash_value - 32));
+		priv->mac_hash2 &= ~hash_bit;
+	}
+
+	/* return 1 to indicate change in mac_hash registers reqd */
+	return 1;
+}
+
+/* EMAC multicast operation */
+#define EMAC_MULTICAST_ADD	0
+#define EMAC_MULTICAST_DEL	1
+#define EMAC_ALL_MULTI_SET	2
+#define EMAC_ALL_MULTI_CLR	3
+
+/**
+ * emac_add_mcast: Set multicast address in the EMAC adapter (Internal)
+ * @priv: The DaVinci EMAC private adapter structure
+ * @action: multicast operation to perform
+ * mac_addr: mac address to set
+ *
+ * Set multicast addresses in EMAC adapter - internal function
+ *
+ */
+static void emac_add_mcast(struct emac_priv *priv, u32 action, u8 *mac_addr)
+{
+	struct device *emac_dev = &priv->ndev->dev;
+	int update = -1;
+
+	switch (action) {
+	case EMAC_MULTICAST_ADD:
+		update = hash_add(priv, mac_addr);
+		break;
+	case EMAC_MULTICAST_DEL:
+		update = hash_del(priv, mac_addr);
+		break;
+	case EMAC_ALL_MULTI_SET:
+		update = 1;
+		priv->mac_hash1 = EMAC_ALL_MULTI_REG_VALUE;
+		priv->mac_hash2 = EMAC_ALL_MULTI_REG_VALUE;
+		break;
+	case EMAC_ALL_MULTI_CLR:
+		update = 1;
+		priv->mac_hash1 = 0;
+		priv->mac_hash2 = 0;
+		memset(&(priv->multicast_hash_cnt[0]), 0,
+		sizeof(priv->multicast_hash_cnt[0]) *
+		       EMAC_NUM_MULTICAST_BITS);
+		break;
+	default:
+		if (netif_msg_drv(priv))
+			dev_err(emac_dev, "DaVinci EMAC: add_mcast"\
+				": bad operation %d", action);
+		break;
+	}
+
+	/* write to the hardware only if the register status chances */
+	if (update > 0) {
+		emac_write(EMAC_MACHASH1, priv->mac_hash1);
+		emac_write(EMAC_MACHASH2, priv->mac_hash2);
+	}
+}
+
+/**
+ * emac_dev_mcast_set: Set multicast address in the EMAC adapter
+ * @ndev: The DaVinci EMAC network adapter
+ *
+ * Set multicast addresses in EMAC adapter
+ *
+ */
+static void emac_dev_mcast_set(struct net_device *ndev)
+{
+	u32 mbp_enable;
+	struct emac_priv *priv = netdev_priv(ndev);
+
+	mbp_enable = emac_read(EMAC_RXMBPENABLE);
+	if (ndev->flags & IFF_PROMISC) {
+		mbp_enable &= (~EMAC_MBP_PROMISCCH(EMAC_DEF_PROM_CH));
+		mbp_enable |= (EMAC_MBP_RXPROMISC);
+	} else {
+		mbp_enable = (mbp_enable & ~EMAC_MBP_RXPROMISC);
+		if ((ndev->flags & IFF_ALLMULTI) ||
+		    (ndev->mc_count > EMAC_DEF_MAX_MULTICAST_ADDRESSES)) {
+			mbp_enable = (mbp_enable | EMAC_MBP_RXMCAST);
+			emac_add_mcast(priv, EMAC_ALL_MULTI_SET, NULL);
+		}
+		if (ndev->mc_count > 0) {
+			struct dev_mc_list *mc_ptr;
+			mbp_enable = (mbp_enable | EMAC_MBP_RXMCAST);
+			emac_add_mcast(priv, EMAC_ALL_MULTI_CLR, NULL);
+			/* program multicast address list into EMAC hardware */
+			for (mc_ptr = ndev->mc_list; mc_ptr;
+			     mc_ptr = mc_ptr->next) {
+				emac_add_mcast(priv, EMAC_MULTICAST_ADD,
+					       (u8 *)mc_ptr->dmi_addr);
+			}
+		} else {
+			mbp_enable = (mbp_enable & ~EMAC_MBP_RXMCAST);
+			emac_add_mcast(priv, EMAC_ALL_MULTI_CLR, NULL);
+		}
+	}
+	/* Set mbp config register */
+	emac_write(EMAC_RXMBPENABLE, mbp_enable);
+}
+
+/*************************************************************************
+ *  EMAC Hardware manipulation
+ *************************************************************************/
+
+/**
+ * emac_int_disable: Disable EMAC module interrupt (from adapter)
+ * @priv: The DaVinci EMAC private adapter structure
+ *
+ * Disable EMAC interrupt on the adapter
+ *
+ */
+static void emac_int_disable(struct emac_priv *priv)
+{
+	if (priv->version == EMAC_VERSION_2) {
+		unsigned long flags;
+
+		local_irq_save(flags);
+
+		/* Program C0_Int_En to zero to turn off
+		* interrupts to the CPU */
+		emac_ctrl_write(EMAC_DM646X_CMRXINTEN, 0x0);
+		emac_ctrl_write(EMAC_DM646X_CMTXINTEN, 0x0);
+		/* NOTE: Rx Threshold and Misc interrupts are not disabled */
+
+		local_irq_restore(flags);
+
+	} else {
+		/* Set DM644x control registers for interrupt control */
+		emac_ctrl_write(EMAC_CTRL_EWCTL, 0x0);
+	}
+}
+
+/**
+ * emac_int_enable: Enable EMAC module interrupt (from adapter)
+ * @priv: The DaVinci EMAC private adapter structure
+ *
+ * Enable EMAC interrupt on the adapter
+ *
+ */
+static void emac_int_enable(struct emac_priv *priv)
+{
+	if (priv->version == EMAC_VERSION_2) {
+		emac_ctrl_write(EMAC_DM646X_CMRXINTEN, 0xff);
+		emac_ctrl_write(EMAC_DM646X_CMTXINTEN, 0xff);
+
+		/* In addition to turning on interrupt Enable, we need
+		 * ack by writing appropriate values to the EOI
+		 * register */
+
+		/* NOTE: Rx Threshold and Misc interrupts are not enabled */
+
+		/* ack rxen only then a new pulse will be generated */
+		emac_write(EMAC_DM646X_MACEOIVECTOR,
+			EMAC_DM646X_MAC_EOI_C0_RXEN);
+
+		/* ack txen- only then a new pulse will be generated */
+		emac_write(EMAC_DM646X_MACEOIVECTOR,
+			EMAC_DM646X_MAC_EOI_C0_TXEN);
+
+	} else {
+		/* Set DM644x control registers for interrupt control */
+		emac_ctrl_write(EMAC_CTRL_EWCTL, 0x1);
+	}
+}
+
+/**
+ * emac_irq: EMAC interrupt handler
+ * @irq: interrupt number
+ * @dev_id: EMAC network adapter data structure ptr
+ *
+ * EMAC Interrupt handler - we only schedule NAPI and not process any packets
+ * here. EVen the interrupt status is checked (TX/RX/Err) in NAPI poll function
+ *
+ * Returns interrupt handled condition
+ */
+static irqreturn_t emac_irq(int irq, void *dev_id)
+{
+	struct net_device *ndev = (struct net_device *)dev_id;
+	struct emac_priv *priv = netdev_priv(ndev);
+
+	++priv->isr_count;
+	if (likely(netif_running(priv->ndev))) {
+		emac_int_disable(priv);
+		napi_schedule(&priv->napi);
+	} else {
+		/* we are closing down, so dont process anything */
+	}
+	return IRQ_HANDLED;
+}
+
+/** EMAC on-chip buffer descriptor memory
+ *
+ * WARNING: Please note that the on chip memory is used for both TX and RX
+ * buffer descriptor queues and is equally divided between TX and RX desc's
+ * If the number of TX or RX descriptors change this memory pointers need
+ * to be adjusted. If external memory is allocated then these pointers can
+ * pointer to the memory
+ *
+ */
+#define EMAC_TX_BD_MEM(priv)	((priv)->emac_ctrl_ram)
+#define EMAC_RX_BD_MEM(priv)	((priv)->emac_ctrl_ram + \
+				(((priv)->ctrl_ram_size) >> 1))
+
+/**
+ * emac_init_txch: TX channel initialization
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: RX channel number
+ *
+ * Called during device init to setup a TX channel (allocate buffer desc
+ * create free pool and keep ready for transmission
+ *
+ * Returns success(0) or mem alloc failures error code
+ */
+static int emac_init_txch(struct emac_priv *priv, u32 ch)
+{
+	struct device *emac_dev = &priv->ndev->dev;
+	u32 cnt, bd_size;
+	void __iomem *mem;
+	struct emac_tx_bd __iomem *curr_bd;
+	struct emac_txch *txch = NULL;
+
+	txch = kzalloc(sizeof(struct emac_txch), GFP_KERNEL);
+	if (NULL == txch) {
+		dev_err(emac_dev, "DaVinci EMAC: TX Ch mem alloc failed");
+		return -ENOMEM;
+	}
+	priv->txch[ch] = txch;
+	txch->service_max = EMAC_DEF_TX_MAX_SERVICE;
+	txch->active_queue_head = NULL;
+	txch->active_queue_tail = NULL;
+	txch->queue_active = 0;
+	txch->teardown_pending = 0;
+
+	/* allocate memory for TX CPPI channel on a 4 byte boundry */
+	txch->tx_complete = kzalloc(txch->service_max * sizeof(u32),
+				    GFP_KERNEL);
+	if (NULL == txch->tx_complete) {
+		dev_err(emac_dev, "DaVinci EMAC: Tx service mem alloc failed");
+		kfree(txch);
+		return -ENOMEM;
+	}
+
+	/* allocate buffer descriptor pool align every BD on four word
+	 * boundry for future requirements */
+	bd_size = (sizeof(struct emac_tx_bd) + 0xF) & ~0xF;
+	txch->num_bd = (priv->ctrl_ram_size >> 1) / bd_size;
+	txch->alloc_size = (((bd_size * txch->num_bd) + 0xF) & ~0xF);
+
+	/* alloc TX BD memory */
+	txch->bd_mem = EMAC_TX_BD_MEM(priv);
+	__memzero((void __force *)txch->bd_mem, txch->alloc_size);
+
+	/* initialize the BD linked list */
+	mem = (void __force __iomem *)
+			(((u32 __force) txch->bd_mem + 0xF) & ~0xF);
+	txch->bd_pool_head = NULL;
+	for (cnt = 0; cnt < txch->num_bd; cnt++) {
+		curr_bd = mem + (cnt * bd_size);
+		curr_bd->next = txch->bd_pool_head;
+		txch->bd_pool_head = curr_bd;
+	}
+
+	/* reset statistics counters */
+	txch->out_of_tx_bd = 0;
+	txch->no_active_pkts = 0;
+	txch->active_queue_count = 0;
+
+	return 0;
+}
+
+/**
+ * emac_cleanup_txch: Book-keep function to clean TX channel resources
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: TX channel number
+ *
+ * Called to clean up TX channel resources
+ *
+ */
+static void emac_cleanup_txch(struct emac_priv *priv, u32 ch)
+{
+	struct emac_txch *txch = priv->txch[ch];
+
+	if (txch) {
+		if (txch->bd_mem)
+			txch->bd_mem = NULL;
+		kfree(txch->tx_complete);
+		kfree(txch);
+		priv->txch[ch] = NULL;
+	}
+}
+
+/**
+ * emac_net_tx_complete: TX packet completion function
+ * @priv: The DaVinci EMAC private adapter structure
+ * @net_data_tokens: packet token - skb pointer
+ * @num_tokens: number of skb's to free
+ * @ch: TX channel number
+ *
+ * Frees the skb once packet is transmitted
+ *
+ */
+static int emac_net_tx_complete(struct emac_priv *priv,
+				void **net_data_tokens,
+				int num_tokens, u32 ch)
+{
+	u32 cnt;
+
+	if (unlikely(num_tokens && netif_queue_stopped(priv->ndev)))
+		netif_start_queue(priv->ndev);
+	for (cnt = 0; cnt < num_tokens; cnt++) {
+		struct sk_buff *skb = (struct sk_buff *)net_data_tokens[cnt];
+		if (skb == NULL)
+			continue;
+		priv->net_dev_stats.tx_packets++;
+		priv->net_dev_stats.tx_bytes += skb->len;
+		dev_kfree_skb_any(skb);
+	}
+	return 0;
+}
+
+/**
+ * emac_txch_teardown: TX channel teardown
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: TX channel number
+ *
+ * Called to teardown TX channel
+ *
+ */
+static void emac_txch_teardown(struct emac_priv *priv, u32 ch)
+{
+	struct device *emac_dev = &priv->ndev->dev;
+	u32 teardown_cnt = 0xFFFFFFF0; /* Some high value */
+	struct emac_txch *txch = priv->txch[ch];
+	struct emac_tx_bd __iomem *curr_bd;
+
+	while ((emac_read(EMAC_TXCP(ch)) & EMAC_TEARDOWN_VALUE) !=
+	       EMAC_TEARDOWN_VALUE) {
+		/* wait till tx teardown complete */
+		cpu_relax(); /* TODO: check if this helps ... */
+		--teardown_cnt;
+		if (0 == teardown_cnt) {
+			dev_err(emac_dev, "EMAC: TX teardown aborted\n");
+			break;
+		}
+	}
+	emac_write(EMAC_TXCP(ch), EMAC_TEARDOWN_VALUE);
+
+	/* process sent packets and return skb's to upper layer */
+	if (1 == txch->queue_active) {
+		curr_bd = txch->active_queue_head;
+		while (curr_bd != NULL) {
+			emac_net_tx_complete(priv, (void __force *)
+					&curr_bd->buf_token, 1, ch);
+			if (curr_bd != txch->active_queue_tail)
+				curr_bd = curr_bd->next;
+			else
+				break;
+		}
+		txch->bd_pool_head = txch->active_queue_head;
+		txch->active_queue_head =
+		txch->active_queue_tail = NULL;
+	}
+}
+
+/**
+ * emac_stop_txch: Stop TX channel operation
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: TX channel number
+ *
+ * Called to stop TX channel operation
+ *
+ */
+static void emac_stop_txch(struct emac_priv *priv, u32 ch)
+{
+	struct emac_txch *txch = priv->txch[ch];
+
+	if (txch) {
+		txch->teardown_pending = 1;
+		emac_write(EMAC_TXTEARDOWN, 0);
+		emac_txch_teardown(priv, ch);
+		txch->teardown_pending = 0;
+		emac_write(EMAC_TXINTMASKCLEAR, BIT(ch));
+	}
+}
+
+/**
+ * emac_tx_bdproc: TX buffer descriptor (packet) processing
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: TX channel number to process buffer descriptors for
+ * @budget: number of packets allowed to process
+ * @pending: indication to caller that packets are pending to process
+ *
+ * Processes TX buffer descriptors after packets are transmitted - checks
+ * ownership bit on the TX * descriptor and requeues it to free pool & frees
+ * the SKB buffer. Only "budget" number of packets are processed and
+ * indication of pending packets provided to the caller
+ *
+ * Returns number of packets processed
+ */
+static int emac_tx_bdproc(struct emac_priv *priv, u32 ch, u32 budget)
+{
+	struct device *emac_dev = &priv->ndev->dev;
+	unsigned long flags;
+	u32 frame_status;
+	u32 pkts_processed = 0;
+	u32 tx_complete_cnt = 0;
+	struct emac_tx_bd __iomem *curr_bd;
+	struct emac_txch *txch = priv->txch[ch];
+	u32 *tx_complete_ptr = txch->tx_complete;
+
+	if (unlikely(1 == txch->teardown_pending)) {
+		if (netif_msg_tx_err(priv) && net_ratelimit()) {
+			dev_err(emac_dev, "DaVinci EMAC:emac_tx_bdproc: "\
+				"teardown pending\n");
+		}
+		return 0;  /* dont handle any pkt completions */
+	}
+
+	++txch->proc_count;
+	spin_lock_irqsave(&priv->tx_lock, flags);
+	curr_bd = txch->active_queue_head;
+	if (NULL == curr_bd) {
+		emac_write(EMAC_TXCP(ch),
+			   emac_virt_to_phys(txch->last_hw_bdprocessed));
+		txch->no_active_pkts++;
+		spin_unlock_irqrestore(&priv->tx_lock, flags);
+		return 0;
+	}
+	BD_CACHE_INVALIDATE(curr_bd, EMAC_BD_LENGTH_FOR_CACHE);
+	frame_status = curr_bd->mode;
+	while ((curr_bd) &&
+	      ((frame_status & EMAC_CPPI_OWNERSHIP_BIT) == 0) &&
+	      (pkts_processed < budget)) {
+		emac_write(EMAC_TXCP(ch), emac_virt_to_phys(curr_bd));
+		txch->active_queue_head = curr_bd->next;
+		if (frame_status & EMAC_CPPI_EOQ_BIT) {
+			if (curr_bd->next) {	/* misqueued packet */
+				emac_write(EMAC_TXHDP(ch), curr_bd->h_next);
+				++txch->mis_queued_packets;
+			} else {
+				txch->queue_active = 0; /* end of queue */
+			}
+		}
+		*tx_complete_ptr = (u32) curr_bd->buf_token;
+		++tx_complete_ptr;
+		++tx_complete_cnt;
+		curr_bd->next = txch->bd_pool_head;
+		txch->bd_pool_head = curr_bd;
+		--txch->active_queue_count;
+		pkts_processed++;
+		txch->last_hw_bdprocessed = curr_bd;
+		curr_bd = txch->active_queue_head;
+		if (curr_bd) {
+			BD_CACHE_INVALIDATE(curr_bd, EMAC_BD_LENGTH_FOR_CACHE);
+			frame_status = curr_bd->mode;
+		}
+	} /* end of pkt processing loop */
+
+	emac_net_tx_complete(priv,
+			     (void *)&txch->tx_complete[0],
+			     tx_complete_cnt, ch);
+	spin_unlock_irqrestore(&priv->tx_lock, flags);
+	return pkts_processed;
+}
+
+#define EMAC_ERR_TX_OUT_OF_BD -1
+
+/**
+ * emac_send: EMAC Transmit function (internal)
+ * @priv: The DaVinci EMAC private adapter structure
+ * @pkt: packet pointer (contains skb ptr)
+ * @ch: TX channel number
+ *
+ * Called by the transmit function to queue the packet in EMAC hardware queue
+ *
+ * Returns success(0) or error code (typically out of desc's)
+ */
+static int emac_send(struct emac_priv *priv, struct emac_netpktobj *pkt, u32 ch)
+{
+	unsigned long flags;
+	struct emac_tx_bd __iomem *curr_bd;
+	struct emac_txch *txch;
+	struct emac_netbufobj *buf_list;
+
+	txch = priv->txch[ch];
+	buf_list = pkt->buf_list;   /* get handle to the buffer array */
+
+	/* check packet size and pad if short */
+	if (pkt->pkt_length < EMAC_DEF_MIN_ETHPKTSIZE) {
+		buf_list->length += (EMAC_DEF_MIN_ETHPKTSIZE - pkt->pkt_length);
+		pkt->pkt_length = EMAC_DEF_MIN_ETHPKTSIZE;
+	}
+
+	spin_lock_irqsave(&priv->tx_lock, flags);
+	curr_bd = txch->bd_pool_head;
+	if (curr_bd == NULL) {
+		txch->out_of_tx_bd++;
+		spin_unlock_irqrestore(&priv->tx_lock, flags);
+		return EMAC_ERR_TX_OUT_OF_BD;
+	}
+
+	txch->bd_pool_head = curr_bd->next;
+	curr_bd->buf_token = buf_list->buf_token;
+	/* FIXME buff_ptr = dma_map_single(... data_ptr ...) */
+	curr_bd->buff_ptr = virt_to_phys(buf_list->data_ptr);
+	curr_bd->off_b_len = buf_list->length;
+	curr_bd->h_next = 0;
+	curr_bd->next = NULL;
+	curr_bd->mode = (EMAC_CPPI_SOP_BIT | EMAC_CPPI_OWNERSHIP_BIT |
+			 EMAC_CPPI_EOP_BIT | pkt->pkt_length);
+
+	/* flush the packet from cache if write back cache is present */
+	BD_CACHE_WRITEBACK_INVALIDATE(curr_bd, EMAC_BD_LENGTH_FOR_CACHE);
+
+	/* send the packet */
+	if (txch->active_queue_head == NULL) {
+		txch->active_queue_head = curr_bd;
+		txch->active_queue_tail = curr_bd;
+		if (1 != txch->queue_active) {
+			emac_write(EMAC_TXHDP(ch),
+					emac_virt_to_phys(curr_bd));
+			txch->queue_active = 1;
+		}
+		++txch->queue_reinit;
+	} else {
+		register struct emac_tx_bd __iomem *tail_bd;
+		register u32 frame_status;
+
+		tail_bd = txch->active_queue_tail;
+		tail_bd->next = curr_bd;
+		txch->active_queue_tail = curr_bd;
+		tail_bd = EMAC_VIRT_NOCACHE(tail_bd);
+		tail_bd->h_next = (int)emac_virt_to_phys(curr_bd);
+		frame_status = tail_bd->mode;
+		if (frame_status & EMAC_CPPI_EOQ_BIT) {
+			emac_write(EMAC_TXHDP(ch), emac_virt_to_phys(curr_bd));
+			frame_status &= ~(EMAC_CPPI_EOQ_BIT);
+			tail_bd->mode = frame_status;
+			++txch->end_of_queue_add;
+		}
+	}
+	txch->active_queue_count++;
+	spin_unlock_irqrestore(&priv->tx_lock, flags);
+	return 0;
+}
+
+/**
+ * emac_dev_xmit: EMAC Transmit function
+ * @skb: SKB pointer
+ * @ndev: The DaVinci EMAC network adapter
+ *
+ * Called by the system to transmit a packet  - we queue the packet in
+ * EMAC hardware transmit queue
+ *
+ * Returns success(NETDEV_TX_OK) or error code (typically out of desc's)
+ */
+static int emac_dev_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+	struct device *emac_dev = &ndev->dev;
+	int ret_code;
+	struct emac_netbufobj tx_buf; /* buffer obj-only single frame support */
+	struct emac_netpktobj tx_packet;  /* packet object */
+	struct emac_priv *priv = netdev_priv(ndev);
+
+	/* If no link, return */
+	if (unlikely(!priv->link)) {
+		if (netif_msg_tx_err(priv) && net_ratelimit())
+			dev_err(emac_dev, "DaVinci EMAC: No link to transmit");
+		return NETDEV_TX_BUSY;
+	}
+
+	/* Build the buffer and packet objects - Since only single fragment is
+	 * supported, need not set length and token in both packet & object.
+	 * Doing so for completeness sake & to show that this needs to be done
+	 * in multifragment case
+	 */
+	tx_packet.buf_list = &tx_buf;
+	tx_packet.num_bufs = 1; /* only single fragment supported */
+	tx_packet.pkt_length = skb->len;
+	tx_packet.pkt_token = (void *)skb;
+	tx_buf.length = skb->len;
+	tx_buf.buf_token = (void *)skb;
+	tx_buf.data_ptr = skb->data;
+	EMAC_CACHE_WRITEBACK((unsigned long)skb->data, skb->len);
+	ndev->trans_start = jiffies;
+	ret_code = emac_send(priv, &tx_packet, EMAC_DEF_TX_CH);
+	if (unlikely(ret_code != 0)) {
+		if (ret_code == EMAC_ERR_TX_OUT_OF_BD) {
+			if (netif_msg_tx_err(priv) && net_ratelimit())
+				dev_err(emac_dev, "DaVinci EMAC: xmit() fatal"\
+					" err. Out of TX BD's");
+			netif_stop_queue(priv->ndev);
+		}
+		priv->net_dev_stats.tx_dropped++;
+		return NETDEV_TX_BUSY;
+	}
+
+	return NETDEV_TX_OK;
+}
+
+/**
+ * emac_dev_tx_timeout: EMAC Transmit timeout function
+ * @ndev: The DaVinci EMAC network adapter
+ *
+ * Called when system detects that a skb timeout period has expired
+ * potentially due to a fault in the adapter in not being able to send
+ * it out on the wire. We teardown the TX channel assuming a hardware
+ * error and re-initialize the TX channel for hardware operation
+ *
+ */
+static void emac_dev_tx_timeout(struct net_device *ndev)
+{
+	struct emac_priv *priv = netdev_priv(ndev);
+	struct device *emac_dev = &ndev->dev;
+
+	if (netif_msg_tx_err(priv))
+		dev_err(emac_dev, "DaVinci EMAC: xmit timeout, restarting TX");
+
+	priv->net_dev_stats.tx_errors++;
+	emac_int_disable(priv);
+	emac_stop_txch(priv, EMAC_DEF_TX_CH);
+	emac_cleanup_txch(priv, EMAC_DEF_TX_CH);
+	emac_init_txch(priv, EMAC_DEF_TX_CH);
+	emac_write(EMAC_TXHDP(0), 0);
+	emac_write(EMAC_TXINTMASKSET, BIT(EMAC_DEF_TX_CH));
+	emac_int_enable(priv);
+}
+
+/**
+ * emac_net_alloc_rx_buf: Allocate a skb for RX
+ * @priv: The DaVinci EMAC private adapter structure
+ * @buf_size: size of SKB data buffer to allocate
+ * @data_token: data token returned (skb handle for storing in buffer desc)
+ * @ch: RX channel number
+ *
+ * Called during RX channel setup - allocates skb buffer of required size
+ * and provides the skb handle and allocated buffer data pointer to caller
+ *
+ * Returns skb data pointer or 0 on failure to alloc skb
+ */
+static void *emac_net_alloc_rx_buf(struct emac_priv *priv, int buf_size,
+		void **data_token, u32 ch)
+{
+	struct net_device *ndev = priv->ndev;
+	struct device *emac_dev = &ndev->dev;
+	struct sk_buff *p_skb;
+
+	p_skb = dev_alloc_skb(buf_size);
+	if (unlikely(NULL == p_skb)) {
+		if (netif_msg_rx_err(priv) && net_ratelimit())
+			dev_err(emac_dev, "DaVinci EMAC: failed to alloc skb");
+		return NULL;
+	}
+
+	/* set device pointer in skb and reserve space for extra bytes */
+	p_skb->dev = ndev;
+	skb_reserve(p_skb, NET_IP_ALIGN);
+	*data_token = (void *) p_skb;
+	EMAC_CACHE_WRITEBACK_INVALIDATE((unsigned long)p_skb->data, buf_size);
+	return p_skb->data;
+}
+
+/**
+ * emac_init_rxch: RX channel initialization
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: RX channel number
+ * @param: mac address for RX channel
+ *
+ * Called during device init to setup a RX channel (allocate buffers and
+ * buffer descriptors, create queue and keep ready for reception
+ *
+ * Returns success(0) or mem alloc failures error code
+ */
+static int emac_init_rxch(struct emac_priv *priv, u32 ch, char *param)
+{
+	struct device *emac_dev = &priv->ndev->dev;
+	u32 cnt, bd_size;
+	void __iomem *mem;
+	struct emac_rx_bd __iomem *curr_bd;
+	struct emac_rxch *rxch = NULL;
+
+	rxch = kzalloc(sizeof(struct emac_rxch), GFP_KERNEL);
+	if (NULL == rxch) {
+		dev_err(emac_dev, "DaVinci EMAC: RX Ch mem alloc failed");
+		return -ENOMEM;
+	}
+	priv->rxch[ch] = rxch;
+	rxch->buf_size = priv->rx_buf_size;
+	rxch->service_max = EMAC_DEF_RX_MAX_SERVICE;
+	rxch->queue_active = 0;
+	rxch->teardown_pending = 0;
+
+	/* save mac address */
+	for (cnt = 0; cnt < 6; cnt++)
+		rxch->mac_addr[cnt] = param[cnt];
+
+	/* allocate buffer descriptor pool align every BD on four word
+	 * boundry for future requirements */
+	bd_size = (sizeof(struct emac_rx_bd) + 0xF) & ~0xF;
+	rxch->num_bd = (priv->ctrl_ram_size >> 1) / bd_size;
+	rxch->alloc_size = (((bd_size * rxch->num_bd) + 0xF) & ~0xF);
+	rxch->bd_mem = EMAC_RX_BD_MEM(priv);
+	__memzero((void __force *)rxch->bd_mem, rxch->alloc_size);
+	rxch->pkt_queue.buf_list = &rxch->buf_queue;
+
+	/* allocate RX buffer and initialize the BD linked list */
+	mem = (void __force __iomem *)
+			(((u32 __force) rxch->bd_mem + 0xF) & ~0xF);
+	rxch->active_queue_head = NULL;
+	rxch->active_queue_tail = mem;
+	for (cnt = 0; cnt < rxch->num_bd; cnt++) {
+		curr_bd = mem + (cnt * bd_size);
+		/* for future use the last parameter contains the BD ptr */
+		curr_bd->data_ptr = emac_net_alloc_rx_buf(priv,
+				    rxch->buf_size,
+				    (void __force **)&curr_bd->buf_token,
+				    EMAC_DEF_RX_CH);
+		if (curr_bd->data_ptr == NULL) {
+			dev_err(emac_dev, "DaVinci EMAC: RX buf mem alloc " \
+				"failed for ch %d\n", ch);
+			kfree(rxch);
+			return -ENOMEM;
+		}
+
+		/* populate the hardware descriptor */
+		curr_bd->h_next = emac_virt_to_phys(rxch->active_queue_head);
+		/* FIXME buff_ptr = dma_map_single(... data_ptr ...) */
+		curr_bd->buff_ptr = virt_to_phys(curr_bd->data_ptr);
+		curr_bd->off_b_len = rxch->buf_size;
+		curr_bd->mode = EMAC_CPPI_OWNERSHIP_BIT;
+
+		/* write back to hardware memory */
+		BD_CACHE_WRITEBACK_INVALIDATE((u32) curr_bd,
+					      EMAC_BD_LENGTH_FOR_CACHE);
+		curr_bd->next = rxch->active_queue_head;
+		rxch->active_queue_head = curr_bd;
+	}
+
+	/* At this point rxCppi->activeQueueHead points to the first
+	   RX BD ready to be given to RX HDP and rxch->active_queue_tail
+	   points to the last RX BD
+	 */
+	return 0;
+}
+
+/**
+ * emac_rxch_teardown: RX channel teardown
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: RX channel number
+ *
+ * Called during device stop to teardown RX channel
+ *
+ */
+static void emac_rxch_teardown(struct emac_priv *priv, u32 ch)
+{
+	struct device *emac_dev = &priv->ndev->dev;
+	u32 teardown_cnt = 0xFFFFFFF0; /* Some high value */
+
+	while ((emac_read(EMAC_RXCP(ch)) & EMAC_TEARDOWN_VALUE) !=
+	       EMAC_TEARDOWN_VALUE) {
+		/* wait till tx teardown complete */
+		cpu_relax(); /* TODO: check if this helps ... */
+		--teardown_cnt;
+		if (0 == teardown_cnt) {
+			dev_err(emac_dev, "EMAC: RX teardown aborted\n");
+			break;
+		}
+	}
+	emac_write(EMAC_RXCP(ch), EMAC_TEARDOWN_VALUE);
+}
+
+/**
+ * emac_stop_rxch: Stop RX channel operation
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: RX channel number
+ *
+ * Called during device stop to stop RX channel operation
+ *
+ */
+static void emac_stop_rxch(struct emac_priv *priv, u32 ch)
+{
+	struct emac_rxch *rxch = priv->rxch[ch];
+
+	if (rxch) {
+		rxch->teardown_pending = 1;
+		emac_write(EMAC_RXTEARDOWN, ch);
+		/* wait for teardown complete */
+		emac_rxch_teardown(priv, ch);
+		rxch->teardown_pending = 0;
+		emac_write(EMAC_RXINTMASKCLEAR, BIT(ch));
+	}
+}
+
+/**
+ * emac_cleanup_rxch: Book-keep function to clean RX channel resources
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: RX channel number
+ *
+ * Called during device stop to clean up RX channel resources
+ *
+ */
+static void emac_cleanup_rxch(struct emac_priv *priv, u32 ch)
+{
+	struct emac_rxch *rxch = priv->rxch[ch];
+	struct emac_rx_bd __iomem *curr_bd;
+
+	if (rxch) {
+		/* free the receive buffers previously allocated */
+		curr_bd = rxch->active_queue_head;
+		while (curr_bd) {
+			if (curr_bd->buf_token) {
+				dev_kfree_skb_any((struct sk_buff *)\
+						  curr_bd->buf_token);
+			}
+			curr_bd = curr_bd->next;
+		}
+		if (rxch->bd_mem)
+			rxch->bd_mem = NULL;
+		kfree(rxch);
+		priv->rxch[ch] = NULL;
+	}
+}
+
+/**
+ * emac_set_type0addr: Set EMAC Type0 mac address
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: RX channel number
+ * @mac_addr: MAC address to set in device
+ *
+ * Called internally to set Type0 mac address of the adapter (Device)
+ *
+ * Returns success (0) or appropriate error code (none as of now)
+ */
+static void emac_set_type0addr(struct emac_priv *priv, u32 ch, char *mac_addr)
+{
+	u32 val;
+	val = ((mac_addr[5] << 8) | (mac_addr[4]));
+	emac_write(EMAC_MACSRCADDRLO, val);
+
+	val = ((mac_addr[3] << 24) | (mac_addr[2] << 16) | \
+	       (mac_addr[1] << 8) | (mac_addr[0]));
+	emac_write(EMAC_MACSRCADDRHI, val);
+	val = emac_read(EMAC_RXUNICASTSET);
+	val |= BIT(ch);
+	emac_write(EMAC_RXUNICASTSET, val);
+	val = emac_read(EMAC_RXUNICASTCLEAR);
+	val &= ~BIT(ch);
+	emac_write(EMAC_RXUNICASTCLEAR, val);
+}
+
+/**
+ * emac_set_type1addr: Set EMAC Type1 mac address
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: RX channel number
+ * @mac_addr: MAC address to set in device
+ *
+ * Called internally to set Type1 mac address of the adapter (Device)
+ *
+ * Returns success (0) or appropriate error code (none as of now)
+ */
+static void emac_set_type1addr(struct emac_priv *priv, u32 ch, char *mac_addr)
+{
+	u32 val;
+	emac_write(EMAC_MACINDEX, ch);
+	val = ((mac_addr[5] << 8) | mac_addr[4]);
+	emac_write(EMAC_MACADDRLO, val);
+	val = ((mac_addr[3] << 24) | (mac_addr[2] << 16) | \
+	       (mac_addr[1] << 8) | (mac_addr[0]));
+	emac_write(EMAC_MACADDRHI, val);
+	emac_set_type0addr(priv, ch, mac_addr);
+}
+
+/**
+ * emac_set_type2addr: Set EMAC Type2 mac address
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: RX channel number
+ * @mac_addr: MAC address to set in device
+ * @index: index into RX address entries
+ * @match: match parameter for RX address matching logic
+ *
+ * Called internally to set Type2 mac address of the adapter (Device)
+ *
+ * Returns success (0) or appropriate error code (none as of now)
+ */
+static void emac_set_type2addr(struct emac_priv *priv, u32 ch,
+			       char *mac_addr, int index, int match)
+{
+	u32 val;
+	emac_write(EMAC_MACINDEX, index);
+	val = ((mac_addr[3] << 24) | (mac_addr[2] << 16) | \
+	       (mac_addr[1] << 8) | (mac_addr[0]));
+	emac_write(EMAC_MACADDRHI, val);
+	val = ((mac_addr[5] << 8) | mac_addr[4] | ((ch & 0x7) << 16) | \
+	       (match << 19) | BIT(20));
+	emac_write(EMAC_MACADDRLO, val);
+	emac_set_type0addr(priv, ch, mac_addr);
+}
+
+/**
+ * emac_setmac: Set mac address in the adapter (internal function)
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: RX channel number
+ * @mac_addr: MAC address to set in device
+ *
+ * Called internally to set the mac address of the adapter (Device)
+ *
+ * Returns success (0) or appropriate error code (none as of now)
+ */
+static void emac_setmac(struct emac_priv *priv, u32 ch, char *mac_addr)
+{
+	struct device *emac_dev = &priv->ndev->dev;
+
+	if (priv->rx_addr_type == 0) {
+		emac_set_type0addr(priv, ch, mac_addr);
+	} else if (priv->rx_addr_type == 1) {
+		u32 cnt;
+		for (cnt = 0; cnt < EMAC_MAX_TXRX_CHANNELS; cnt++)
+			emac_set_type1addr(priv, ch, mac_addr);
+	} else if (priv->rx_addr_type == 2) {
+		emac_set_type2addr(priv, ch, mac_addr, ch, 1);
+		emac_set_type0addr(priv, ch, mac_addr);
+	} else {
+		if (netif_msg_drv(priv))
+			dev_err(emac_dev, "DaVinci EMAC: Wrong addressing\n");
+	}
+}
+
+/**
+ * emac_dev_setmac_addr: Set mac address in the adapter
+ * @ndev: The DaVinci EMAC network adapter
+ * @addr: MAC address to set in device
+ *
+ * Called by the system to set the mac address of the adapter (Device)
+ *
+ * Returns success (0) or appropriate error code (none as of now)
+ */
+static int emac_dev_setmac_addr(struct net_device *ndev, void *addr)
+{
+	struct emac_priv *priv = netdev_priv(ndev);
+	struct emac_rxch *rxch = priv->rxch[EMAC_DEF_RX_CH];
+	struct device *emac_dev = &priv->ndev->dev;
+	struct sockaddr *sa = addr;
+	DECLARE_MAC_BUF(mac);
+
+	/* Store mac addr in priv and rx channel and set it in EMAC hw */
+	memcpy(priv->mac_addr, sa->sa_data, ndev->addr_len);
+	memcpy(rxch->mac_addr, sa->sa_data, ndev->addr_len);
+	memcpy(ndev->dev_addr, sa->sa_data, ndev->addr_len);
+	emac_setmac(priv, EMAC_DEF_RX_CH, rxch->mac_addr);
+
+	if (netif_msg_drv(priv))
+		dev_notice(emac_dev, "DaVinci EMAC: emac_dev_setmac_addr %s\n",
+			   print_mac(mac, priv->mac_addr));
+
+	return 0;
+}
+
+/**
+ * emac_addbd_to_rx_queue: Recycle RX buffer descriptor
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: RX channel number to process buffer descriptors for
+ * @curr_bd: current buffer descriptor
+ * @buffer: buffer pointer for descriptor
+ * @buf_token: buffer token (stores skb information)
+ *
+ * Prepares the recycled buffer descriptor and addes it to hardware
+ * receive queue - if queue empty this descriptor becomes the head
+ * else addes the descriptor to end of queue
+ *
+ */
+static void emac_addbd_to_rx_queue(struct emac_priv *priv, u32 ch,
+		struct emac_rx_bd __iomem *curr_bd,
+		char *buffer, void *buf_token)
+{
+	struct emac_rxch *rxch = priv->rxch[ch];
+
+	/* populate the hardware descriptor */
+	curr_bd->h_next = 0;
+	/* FIXME buff_ptr = dma_map_single(... buffer ...) */
+	curr_bd->buff_ptr = virt_to_phys(buffer);
+	curr_bd->off_b_len = rxch->buf_size;
+	curr_bd->mode = EMAC_CPPI_OWNERSHIP_BIT;
+	curr_bd->next = NULL;
+	curr_bd->data_ptr = buffer;
+	curr_bd->buf_token = buf_token;
+
+	/* write back  */
+	BD_CACHE_WRITEBACK_INVALIDATE(curr_bd, EMAC_BD_LENGTH_FOR_CACHE);
+	if (rxch->active_queue_head == NULL) {
+		rxch->active_queue_head = curr_bd;
+		rxch->active_queue_tail = curr_bd;
+		if (0 != rxch->queue_active) {
+			emac_write(EMAC_RXHDP(ch),
+				   emac_virt_to_phys(rxch->active_queue_head));
+			rxch->queue_active = 1;
+		}
+	} else {
+		struct emac_rx_bd __iomem *tail_bd;
+		u32 frame_status;
+
+		tail_bd = rxch->active_queue_tail;
+		rxch->active_queue_tail = curr_bd;
+		tail_bd->next = curr_bd;
+		tail_bd = EMAC_VIRT_NOCACHE(tail_bd);
+		tail_bd->h_next = emac_virt_to_phys(curr_bd);
+		frame_status = tail_bd->mode;
+		if (frame_status & EMAC_CPPI_EOQ_BIT) {
+			emac_write(EMAC_RXHDP(ch),
+					emac_virt_to_phys(curr_bd));
+			frame_status &= ~(EMAC_CPPI_EOQ_BIT);
+			tail_bd->mode = frame_status;
+			++rxch->end_of_queue_add;
+		}
+	}
+	++rxch->recycled_bd;
+}
+
+/**
+ * emac_net_rx_cb: Prepares packet and sends to upper layer
+ * @priv: The DaVinci EMAC private adapter structure
+ * @net_pkt_list: Network packet list (received packets)
+ *
+ * Invalidates packet buffer memory and sends the received packet to upper
+ * layer
+ *
+ * Returns success or appropriate error code (none as of now)
+ */
+static int emac_net_rx_cb(struct emac_priv *priv,
+			  struct emac_netpktobj *net_pkt_list)
+{
+	struct sk_buff *p_skb;
+	p_skb = (struct sk_buff *)net_pkt_list->pkt_token;
+	/* set length of packet */
+	skb_put(p_skb, net_pkt_list->pkt_length);
+	EMAC_CACHE_INVALIDATE((unsigned long)p_skb->data, p_skb->len);
+	p_skb->protocol = eth_type_trans(p_skb, priv->ndev);
+	p_skb->dev->last_rx = jiffies;
+	netif_receive_skb(p_skb);
+	priv->net_dev_stats.rx_bytes += net_pkt_list->pkt_length;
+	priv->net_dev_stats.rx_packets++;
+	return 0;
+}
+
+/**
+ * emac_rx_bdproc: RX buffer descriptor (packet) processing
+ * @priv: The DaVinci EMAC private adapter structure
+ * @ch: RX channel number to process buffer descriptors for
+ * @budget: number of packets allowed to process
+ * @pending: indication to caller that packets are pending to process
+ *
+ * Processes RX buffer descriptors - checks ownership bit on the RX buffer
+ * descriptor, sends the receive packet to upper layer, allocates a new SKB
+ * and recycles the buffer descriptor (requeues it in hardware RX queue).
+ * Only "budget" number of packets are processed and indication of pending
+ * packets provided to the caller.
+ *
+ * Returns number of packets processed (and indication of pending packets)
+ */
+static int emac_rx_bdproc(struct emac_priv *priv, u32 ch, u32 budget)
+{
+	unsigned long flags;
+	u32 frame_status;
+	u32 pkts_processed = 0;
+	char *new_buffer;
+	struct emac_rx_bd __iomem *curr_bd;
+	struct emac_rx_bd __iomem *last_bd;
+	struct emac_netpktobj *curr_pkt, pkt_obj;
+	struct emac_netbufobj buf_obj;
+	struct emac_netbufobj *rx_buf_obj;
+	void *new_buf_token;
+	struct emac_rxch *rxch = priv->rxch[ch];
+
+	if (unlikely(1 == rxch->teardown_pending))
+		return 0;
+	++rxch->proc_count;
+	spin_lock_irqsave(&priv->rx_lock, flags);
+	pkt_obj.buf_list = &buf_obj;
+	curr_pkt = &pkt_obj;
+	curr_bd = rxch->active_queue_head;
+	BD_CACHE_INVALIDATE(curr_bd, EMAC_BD_LENGTH_FOR_CACHE);
+	frame_status = curr_bd->mode;
+
+	while ((curr_bd) &&
+	       ((frame_status & EMAC_CPPI_OWNERSHIP_BIT) == 0) &&
+	       (pkts_processed < budget)) {
+
+		new_buffer = emac_net_alloc_rx_buf(priv, rxch->buf_size,
+					&new_buf_token, EMAC_DEF_RX_CH);
+		if (unlikely(NULL == new_buffer)) {
+			++rxch->out_of_rx_buffers;
+			goto end_emac_rx_bdproc;
+		}
+
+		/* populate received packet data structure */
+		rx_buf_obj = &curr_pkt->buf_list[0];
+		rx_buf_obj->data_ptr = (char *)curr_bd->data_ptr;
+		rx_buf_obj->length = curr_bd->off_b_len & EMAC_RX_BD_BUF_SIZE;
+		rx_buf_obj->buf_token = curr_bd->buf_token;
+		curr_pkt->pkt_token = curr_pkt->buf_list->buf_token;
+		curr_pkt->num_bufs = 1;
+		curr_pkt->pkt_length =
+			(frame_status & EMAC_RX_BD_PKT_LENGTH_MASK);
+		emac_write(EMAC_RXCP(ch), emac_virt_to_phys(curr_bd));
+		++rxch->processed_bd;
+		last_bd = curr_bd;
+		curr_bd = last_bd->next;
+		rxch->active_queue_head = curr_bd;
+
+		/* check if end of RX queue ? */
+		if (frame_status & EMAC_CPPI_EOQ_BIT) {
+			if (curr_bd) {
+				++rxch->mis_queued_packets;
+				emac_write(EMAC_RXHDP(ch),
+					   emac_virt_to_phys(curr_bd));
+			} else {
+				++rxch->end_of_queue;
+				rxch->queue_active = 0;
+			}
+		}
+
+		/* recycle BD */
+		emac_addbd_to_rx_queue(priv, ch, last_bd, new_buffer,
+				       new_buf_token);
+
+		/* return the packet to the user - BD ptr passed in
+		 * last parameter for potential *future* use */
+		spin_unlock_irqrestore(&priv->rx_lock, flags);
+		emac_net_rx_cb(priv, curr_pkt);
+		spin_lock_irqsave(&priv->rx_lock, flags);
+		curr_bd = rxch->active_queue_head;
+		if (curr_bd) {
+			BD_CACHE_INVALIDATE(curr_bd, EMAC_BD_LENGTH_FOR_CACHE);
+			frame_status = curr_bd->mode;
+		}
+		++pkts_processed;
+	}
+
+end_emac_rx_bdproc:
+	spin_unlock_irqrestore(&priv->rx_lock, flags);
+	return pkts_processed;
+}
+
+/**
+ * emac_hw_enable: Enable EMAC hardware for packet transmission/reception
+ * @priv: The DaVinci EMAC private adapter structure
+ *
+ * Enables EMAC hardware for packet processing - enables PHY, enables RX
+ * for packet reception and enables device interrupts and then NAPI
+ *
+ * Returns success (0) or appropriate error code (none right now)
+ */
+static int emac_hw_enable(struct emac_priv *priv)
+{
+	u32 ch, val, mbp_enable, mac_control;
+
+	/* Soft reset */
+	emac_write(EMAC_SOFTRESET, 1);
+	while (emac_read(EMAC_SOFTRESET))
+		cpu_relax();
+
+	/* Disable interrupt & Set pacing for more interrupts initially */
+	emac_int_disable(priv);
+
+	/* Full duplex enable bit set when auto negotiation happens */
+	mac_control =
+		(((EMAC_DEF_TXPRIO_FIXED) ? (EMAC_MACCONTROL_TXPTYPE) : 0x0) |
+		((priv->speed == 1000) ? EMAC_MACCONTROL_GIGABITEN : 0x0) |
+		((EMAC_DEF_TXPACING_EN) ? (EMAC_MACCONTROL_TXPACEEN) : 0x0) |
+		((priv->duplex == DUPLEX_FULL) ? 0x1 : 0));
+	emac_write(EMAC_MACCONTROL, mac_control);
+
+	mbp_enable =
+		(((EMAC_DEF_PASS_CRC) ? (EMAC_RXMBP_PASSCRC_MASK) : 0x0) |
+		((EMAC_DEF_QOS_EN) ? (EMAC_RXMBP_QOSEN_MASK) : 0x0) |
+		 ((EMAC_DEF_NO_BUFF_CHAIN) ? (EMAC_RXMBP_NOCHAIN_MASK) : 0x0) |
+		 ((EMAC_DEF_MACCTRL_FRAME_EN) ? (EMAC_RXMBP_CMFEN_MASK) : 0x0) |
+		 ((EMAC_DEF_SHORT_FRAME_EN) ? (EMAC_RXMBP_CSFEN_MASK) : 0x0) |
+		 ((EMAC_DEF_ERROR_FRAME_EN) ? (EMAC_RXMBP_CEFEN_MASK) : 0x0) |
+		 ((EMAC_DEF_PROM_EN) ? (EMAC_RXMBP_CAFEN_MASK) : 0x0) |
+		 ((EMAC_DEF_PROM_CH & EMAC_RXMBP_CHMASK) << \
+			EMAC_RXMBP_PROMCH_SHIFT) |
+		 ((EMAC_DEF_BCAST_EN) ? (EMAC_RXMBP_BROADEN_MASK) : 0x0) |
+		 ((EMAC_DEF_BCAST_CH & EMAC_RXMBP_CHMASK) << \
+			EMAC_RXMBP_BROADCH_SHIFT) |
+		 ((EMAC_DEF_MCAST_EN) ? (EMAC_RXMBP_MULTIEN_MASK) : 0x0) |
+		 ((EMAC_DEF_MCAST_CH & EMAC_RXMBP_CHMASK) << \
+			EMAC_RXMBP_MULTICH_SHIFT));
+	emac_write(EMAC_RXMBPENABLE, mbp_enable);
+	emac_write(EMAC_RXMAXLEN, (EMAC_DEF_MAX_FRAME_SIZE &
+				   EMAC_RX_MAX_LEN_MASK));
+	emac_write(EMAC_RXBUFFEROFFSET, (EMAC_DEF_BUFFER_OFFSET &
+					 EMAC_RX_BUFFER_OFFSET_MASK));
+	emac_write(EMAC_RXFILTERLOWTHRESH, 0);
+	emac_write(EMAC_RXUNICASTCLEAR, EMAC_RX_UNICAST_CLEAR_ALL);
+	priv->rx_addr_type = (emac_read(EMAC_MACCONFIG) >> 8) & 0xFF;
+
+	val = emac_read(EMAC_TXCONTROL);
+	val |= EMAC_TX_CONTROL_TX_ENABLE_VAL;
+	emac_write(EMAC_TXCONTROL, val);
+	val = emac_read(EMAC_RXCONTROL);
+	val |= EMAC_RX_CONTROL_RX_ENABLE_VAL;
+	emac_write(EMAC_RXCONTROL, val);
+	emac_write(EMAC_MACINTMASKSET, EMAC_MAC_HOST_ERR_INTMASK_VAL);
+
+	for (ch = 0; ch < EMAC_DEF_MAX_TX_CH; ch++) {
+		emac_write(EMAC_TXHDP(ch), 0);
+		emac_write(EMAC_TXINTMASKSET, BIT(ch));
+	}
+	for (ch = 0; ch < EMAC_DEF_MAX_RX_CH; ch++) {
+		struct emac_rxch *rxch = priv->rxch[ch];
+		emac_setmac(priv, ch, rxch->mac_addr);
+		emac_write(EMAC_RXINTMASKSET, BIT(ch));
+		rxch->queue_active = 1;
+		emac_write(EMAC_RXHDP(ch),
+			   emac_virt_to_phys(rxch->active_queue_head));
+	}
+
+	/* Enable MII */
+	val = emac_read(EMAC_MACCONTROL);
+	val |= (EMAC_MACCONTROL_MIIEN);
+	emac_write(EMAC_MACCONTROL, val);
+
+	/* Enable NAPI and interrupts */
+	napi_enable(&priv->napi);
+	emac_int_enable(priv);
+	return 0;
+
+}
+
+/**
+ * emac_poll: EMAC NAPI Poll function
+ * @ndev: The DaVinci EMAC network adapter
+ * @budget: Number of receive packets to process (as told by NAPI layer)
+ *
+ * NAPI Poll function implemented to process packets as per budget. We check
+ * the type of interrupt on the device and accordingly call the TX or RX
+ * packet processing functions. We follow the budget for RX processing and
+ * also put a cap on number of TX pkts processed through config param. The
+ * NAPI schedule function is called if more packets pending.
+ *
+ * Returns number of packets received (in most cases; else TX pkts - rarely)
+ */
+static int emac_poll(struct napi_struct *napi, int budget)
+{
+	unsigned int mask;
+	struct emac_priv *priv = container_of(napi, struct emac_priv, napi);
+	struct net_device *ndev = priv->ndev;
+	struct device *emac_dev = &ndev->dev;
+	u32 status = 0;
+	u32 num_pkts = 0;
+
+	if (!netif_running(ndev))
+		return 0;
+
+	/* Check interrupt vectors and call packet processing */
+	status = emac_read(EMAC_MACINVECTOR);
+
+	mask = EMAC_DM644X_MAC_IN_VECTOR_TX_INT_VEC;
+
+	if (priv->version == EMAC_VERSION_2)
+		mask = EMAC_DM646X_MAC_IN_VECTOR_TX_INT_VEC;
+
+	if (status & mask) {
+		num_pkts = emac_tx_bdproc(priv, EMAC_DEF_TX_CH,
+					  EMAC_DEF_TX_MAX_SERVICE);
+	} /* TX processing */
+
+	if (num_pkts)
+		return budget;
+
+	mask = EMAC_DM644X_MAC_IN_VECTOR_RX_INT_VEC;
+
+	if (priv->version == EMAC_VERSION_2)
+		mask = EMAC_DM646X_MAC_IN_VECTOR_RX_INT_VEC;
+
+	if (status & mask) {
+		num_pkts = emac_rx_bdproc(priv, EMAC_DEF_RX_CH, budget);
+	} /* RX processing */
+
+	if (num_pkts < budget) {
+		napi_complete(napi);
+		emac_int_enable(priv);
+	}
+
+	if (unlikely(status & EMAC_DM644X_MAC_IN_VECTOR_HOST_INT)) {
+		u32 ch, cause;
+		dev_err(emac_dev, "DaVinci EMAC: Fatal Hardware Error\n");
+		netif_stop_queue(ndev);
+		napi_disable(&priv->napi);
+
+		status = emac_read(EMAC_MACSTATUS);
+		cause = ((status & EMAC_MACSTATUS_TXERRCODE_MASK) >>
+			 EMAC_MACSTATUS_TXERRCODE_SHIFT);
+		if (cause) {
+			ch = ((status & EMAC_MACSTATUS_TXERRCH_MASK) >>
+			      EMAC_MACSTATUS_TXERRCH_SHIFT);
+			if (net_ratelimit()) {
+				dev_err(emac_dev, "TX Host error %s on ch=%d\n",
+					&emac_txhost_errcodes[cause][0], ch);
+			}
+		}
+		cause = ((status & EMAC_MACSTATUS_RXERRCODE_MASK) >>
+			 EMAC_MACSTATUS_RXERRCODE_SHIFT);
+		if (cause) {
+			ch = ((status & EMAC_MACSTATUS_RXERRCH_MASK) >>
+			      EMAC_MACSTATUS_RXERRCH_SHIFT);
+			if (netif_msg_hw(priv) && net_ratelimit())
+				dev_err(emac_dev, "RX Host error %s on ch=%d\n",
+					&emac_rxhost_errcodes[cause][0], ch);
+		}
+	} /* Host error processing */
+
+	return num_pkts;
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+/**
+ * emac_poll_controller: EMAC Poll controller function
+ * @ndev: The DaVinci EMAC network adapter
+ *
+ * Polled functionality used by netconsole and others in non interrupt mode
+ *
+ */
+void emac_poll_controller(struct net_device *ndev)
+{
+	struct emac_priv *priv = netdev_priv(ndev);
+
+	emac_int_disable(priv);
+	emac_irq(ndev->irq, priv);
+	emac_int_enable(priv);
+}
+#endif
+
+/* PHY/MII bus related */
+
+/* Wait until mdio is ready for next command */
+#define MDIO_WAIT_FOR_USER_ACCESS\
+		while ((emac_mdio_read((MDIO_USERACCESS(0))) &\
+			MDIO_USERACCESS_GO) != 0)
+
+static int emac_mii_read(struct mii_bus *bus, int phy_id, int phy_reg)
+{
+	unsigned int phy_data = 0;
+	unsigned int phy_control;
+
+	/* Wait until mdio is ready for next command */
+	MDIO_WAIT_FOR_USER_ACCESS;
+
+	phy_control = (MDIO_USERACCESS_GO |
+		       MDIO_USERACCESS_READ |
+		       ((phy_reg << 21) & MDIO_USERACCESS_REGADR) |
+		       ((phy_id << 16) & MDIO_USERACCESS_PHYADR) |
+		       (phy_data & MDIO_USERACCESS_DATA));
+	emac_mdio_write(MDIO_USERACCESS(0), phy_control);
+
+	/* Wait until mdio is ready for next command */
+	MDIO_WAIT_FOR_USER_ACCESS;
+
+	return emac_mdio_read(MDIO_USERACCESS(0)) & MDIO_USERACCESS_DATA;
+
+}
+
+static int emac_mii_write(struct mii_bus *bus, int phy_id,
+			  int phy_reg, u16 phy_data)
+{
+
+	unsigned int control;
+
+	/*  until mdio is ready for next command */
+	MDIO_WAIT_FOR_USER_ACCESS;
+
+	control = (MDIO_USERACCESS_GO |
+		   MDIO_USERACCESS_WRITE |
+		   ((phy_reg << 21) & MDIO_USERACCESS_REGADR) |
+		   ((phy_id << 16) & MDIO_USERACCESS_PHYADR) |
+		   (phy_data & MDIO_USERACCESS_DATA));
+	emac_mdio_write(MDIO_USERACCESS(0), control);
+
+	return 0;
+}
+
+static int emac_mii_reset(struct mii_bus *bus)
+{
+	unsigned int clk_div;
+	int mdio_bus_freq = emac_bus_frequency;
+
+	if (mdio_max_freq & mdio_bus_freq)
+		clk_div = ((mdio_bus_freq / mdio_max_freq) - 1);
+	else
+		clk_div = 0xFF;
+
+	clk_div &= MDIO_CONTROL_CLKDIV;
+
+	/* Set enable and clock divider in MDIOControl */
+	emac_mdio_write(MDIO_CONTROL, (clk_div | MDIO_CONTROL_ENABLE));
+
+	return 0;
+
+}
+
+static int mii_irqs[PHY_MAX_ADDR] = { PHY_POLL, PHY_POLL };
+
+/* emac_driver: EMAC MII bus structure */
+
+static struct mii_bus *emac_mii;
+
+static void emac_adjust_link(struct net_device *ndev)
+{
+	struct emac_priv *priv = netdev_priv(ndev);
+	struct phy_device *phydev = priv->phydev;
+	unsigned long flags;
+	int new_state = 0;
+
+	spin_lock_irqsave(&priv->lock, flags);
+
+	if (phydev->link) {
+		/* check the mode of operation - full/half duplex */
+		if (phydev->duplex != priv->duplex) {
+			new_state = 1;
+			priv->duplex = phydev->duplex;
+		}
+		if (phydev->speed != priv->speed) {
+			new_state = 1;
+			priv->speed = phydev->speed;
+		}
+		if (!priv->link) {
+			new_state = 1;
+			priv->link = 1;
+		}
+
+	} else if (priv->link) {
+		new_state = 1;
+		priv->link = 0;
+		priv->speed = 0;
+		priv->duplex = ~0;
+	}
+	if (new_state) {
+		emac_update_phystatus(priv);
+		phy_print_status(priv->phydev);
+	}
+
+	spin_unlock_irqrestore(&priv->lock, flags);
+}
+
+/*************************************************************************
+ *  Linux Driver Model
+ *************************************************************************/
+
+/**
+ * emac_devioctl: EMAC adapter ioctl
+ * @ndev: The DaVinci EMAC network adapter
+ * @ifrq: request parameter
+ * @cmd: command parameter
+ *
+ * EMAC driver ioctl function
+ *
+ * Returns success(0) or appropriate error code
+ */
+static int emac_devioctl(struct net_device *ndev, struct ifreq *ifrq, int cmd)
+{
+	dev_warn(&ndev->dev, "DaVinci EMAC: ioctl not supported\n");
+
+	if (!(netif_running(ndev)))
+		return -EINVAL;
+
+	/* TODO: Add phy read and write and private statistics get feature */
+
+	return -EOPNOTSUPP;
+}
+
+/**
+ * emac_dev_open: EMAC device open
+ * @ndev: The DaVinci EMAC network adapter
+ *
+ * Called when system wants to start the interface. We init TX/RX channels
+ * and enable the hardware for packet reception/transmission and start the
+ * network queue.
+ *
+ * Returns 0 for a successful open, or appropriate error code
+ */
+static int emac_dev_open(struct net_device *ndev)
+{
+	struct device *emac_dev = &ndev->dev;
+	u32 rc, cnt, ch;
+	int phy_addr;
+	struct resource *res;
+	int q, m;
+	int i = 0;
+	int k = 0;
+	struct emac_priv *priv = netdev_priv(ndev);
+
+	netif_carrier_off(ndev);
+	for (cnt = 0; cnt <= ETH_ALEN; cnt++)
+		ndev->dev_addr[cnt] = priv->mac_addr[cnt];
+
+	/* Configuration items */
+	priv->rx_buf_size = EMAC_DEF_MAX_FRAME_SIZE + NET_IP_ALIGN;
+
+	/* Clear basic hardware */
+	for (ch = 0; ch < EMAC_MAX_TXRX_CHANNELS; ch++) {
+		emac_write(EMAC_TXHDP(ch), 0);
+		emac_write(EMAC_RXHDP(ch), 0);
+		emac_write(EMAC_RXHDP(ch), 0);
+		emac_write(EMAC_RXINTMASKCLEAR, EMAC_INT_MASK_CLEAR);
+		emac_write(EMAC_TXINTMASKCLEAR, EMAC_INT_MASK_CLEAR);
+	}
+	priv->mac_hash1 = 0;
+	priv->mac_hash2 = 0;
+	emac_write(EMAC_MACHASH1, 0);
+	emac_write(EMAC_MACHASH2, 0);
+
+	/* multi ch not supported - open 1 TX, 1RX ch by default */
+	rc = emac_init_txch(priv, EMAC_DEF_TX_CH);
+	if (0 != rc) {
+		dev_err(emac_dev, "DaVinci EMAC: emac_init_txch() failed");
+		return rc;
+	}
+	rc = emac_init_rxch(priv, EMAC_DEF_RX_CH, priv->mac_addr);
+	if (0 != rc) {
+		dev_err(emac_dev, "DaVinci EMAC: emac_init_rxch() failed");
+		return rc;
+	}
+
+	/* Request IRQ */
+
+	while ((res = platform_get_resource(priv->pdev, IORESOURCE_IRQ, k))) {
+		for (i = res->start; i <= res->end; i++) {
+			if (request_irq(i, emac_irq, IRQF_DISABLED,
+					ndev->name, ndev))
+				goto rollback;
+		}
+		k++;
+	}
+
+	/* Start/Enable EMAC hardware */
+	emac_hw_enable(priv);
+
+	/* find the first phy */
+	priv->phydev = NULL;
+	if (priv->phy_mask) {
+		emac_mii_reset(priv->mii_bus);
+		for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++) {
+			if (priv->mii_bus->phy_map[phy_addr]) {
+				priv->phydev = priv->mii_bus->phy_map[phy_addr];
+				break;
+			}
+		}
+
+		if (!priv->phydev) {
+			printk(KERN_ERR "%s: no PHY found\n", ndev->name);
+			return -1;
+		}
+
+		priv->phydev = phy_connect(ndev, dev_name(&priv->phydev->dev),
+				&emac_adjust_link, 0, PHY_INTERFACE_MODE_MII);
+
+		if (IS_ERR(priv->phydev)) {
+			printk(KERN_ERR "%s: Could not attach to PHY\n",
+								ndev->name);
+			return PTR_ERR(priv->phydev);
+		}
+
+		priv->link = 0;
+		priv->speed = 0;
+		priv->duplex = ~0;
+
+		printk(KERN_INFO "%s: attached PHY driver [%s] "
+			"(mii_bus:phy_addr=%s, id=%x)\n", ndev->name,
+			priv->phydev->drv->name, dev_name(&priv->phydev->dev),
+			priv->phydev->phy_id);
+	} else{
+		/* No PHY , fix the link, speed and duplex settings */
+		priv->link = 1;
+		priv->speed = SPEED_100;
+		priv->duplex = DUPLEX_FULL;
+		emac_update_phystatus(priv);
+	}
+
+	if (!netif_running(ndev)) /* debug only - to avoid compiler warning */
+		emac_dump_regs(priv);
+
+	if (netif_msg_drv(priv))
+		dev_notice(emac_dev, "DaVinci EMAC: Opened %s\n", ndev->name);
+
+	if (priv->phy_mask)
+		phy_start(priv->phydev);
+
+	return 0;
+
+rollback:
+
+	dev_err(emac_dev, "DaVinci EMAC: request_irq() failed");
+
+	for (q = k; k >= 0; k--) {
+		for (m = i; m >= res->start; m--)
+			free_irq(m, ndev);
+		res = platform_get_resource(priv->pdev, IORESOURCE_IRQ, k-1);
+		m = res->end;
+	}
+	return -EBUSY;
+}
+
+/**
+ * emac_dev_stop: EMAC device stop
+ * @ndev: The DaVinci EMAC network adapter
+ *
+ * Called when system wants to stop or down the interface. We stop the network
+ * queue, disable interrupts and cleanup TX/RX channels.
+ *
+ * We return the statistics in net_device_stats structure pulled from emac
+ */
+static int emac_dev_stop(struct net_device *ndev)
+{
+	struct resource *res;
+	int i = 0;
+	int irq_num;
+	struct emac_priv *priv = netdev_priv(ndev);
+	struct device *emac_dev = &ndev->dev;
+
+	/* inform the upper layers. */
+	netif_stop_queue(ndev);
+	napi_disable(&priv->napi);
+
+	netif_carrier_off(ndev);
+	emac_int_disable(priv);
+	emac_stop_txch(priv, EMAC_DEF_TX_CH);
+	emac_stop_rxch(priv, EMAC_DEF_RX_CH);
+	emac_cleanup_txch(priv, EMAC_DEF_TX_CH);
+	emac_cleanup_rxch(priv, EMAC_DEF_RX_CH);
+	emac_write(EMAC_SOFTRESET, 1);
+
+	if (priv->phydev)
+		phy_disconnect(priv->phydev);
+
+	/* Free IRQ */
+	while ((res = platform_get_resource(priv->pdev, IORESOURCE_IRQ, i))) {
+		for (irq_num = res->start; irq_num <= res->end; irq_num++)
+			free_irq(irq_num, priv->ndev);
+		i++;
+	}
+
+	if (netif_msg_drv(priv))
+		dev_notice(emac_dev, "DaVinci EMAC: %s stopped\n", ndev->name);
+
+	return 0;
+}
+
+/**
+ * emac_dev_getnetstats: EMAC get statistics function
+ * @ndev: The DaVinci EMAC network adapter
+ *
+ * Called when system wants to get statistics from the device.
+ *
+ * We return the statistics in net_device_stats structure pulled from emac
+ */
+static struct net_device_stats *emac_dev_getnetstats(struct net_device *ndev)
+{
+	struct emac_priv *priv = netdev_priv(ndev);
+
+	/* update emac hardware stats and reset the registers*/
+
+	priv->net_dev_stats.multicast += emac_read(EMAC_RXMCASTFRAMES);
+	emac_write(EMAC_RXMCASTFRAMES, EMAC_ALL_MULTI_REG_VALUE);
+
+	priv->net_dev_stats.collisions += (emac_read(EMAC_TXCOLLISION) +
+					   emac_read(EMAC_TXSINGLECOLL) +
+					   emac_read(EMAC_TXMULTICOLL));
+	emac_write(EMAC_TXCOLLISION, EMAC_ALL_MULTI_REG_VALUE);
+	emac_write(EMAC_TXSINGLECOLL, EMAC_ALL_MULTI_REG_VALUE);
+	emac_write(EMAC_TXMULTICOLL, EMAC_ALL_MULTI_REG_VALUE);
+
+	priv->net_dev_stats.rx_length_errors += (emac_read(EMAC_RXOVERSIZED) +
+						emac_read(EMAC_RXJABBER) +
+						emac_read(EMAC_RXUNDERSIZED));
+	emac_write(EMAC_RXOVERSIZED, EMAC_ALL_MULTI_REG_VALUE);
+	emac_write(EMAC_RXJABBER, EMAC_ALL_MULTI_REG_VALUE);
+	emac_write(EMAC_RXUNDERSIZED, EMAC_ALL_MULTI_REG_VALUE);
+
+	priv->net_dev_stats.rx_over_errors += (emac_read(EMAC_RXSOFOVERRUNS) +
+					       emac_read(EMAC_RXMOFOVERRUNS));
+	emac_write(EMAC_RXSOFOVERRUNS, EMAC_ALL_MULTI_REG_VALUE);
+	emac_write(EMAC_RXMOFOVERRUNS, EMAC_ALL_MULTI_REG_VALUE);
+
+	priv->net_dev_stats.rx_fifo_errors += emac_read(EMAC_RXDMAOVERRUNS);
+	emac_write(EMAC_RXDMAOVERRUNS, EMAC_ALL_MULTI_REG_VALUE);
+
+	priv->net_dev_stats.tx_carrier_errors +=
+		emac_read(EMAC_TXCARRIERSENSE);
+	emac_write(EMAC_TXCARRIERSENSE, EMAC_ALL_MULTI_REG_VALUE);
+
+	priv->net_dev_stats.tx_fifo_errors = emac_read(EMAC_TXUNDERRUN);
+	emac_write(EMAC_TXUNDERRUN, EMAC_ALL_MULTI_REG_VALUE);
+
+	return &priv->net_dev_stats;
+}
+
+static const struct net_device_ops emac_netdev_ops = {
+	.ndo_open		= emac_dev_open,
+	.ndo_stop		= emac_dev_stop,
+	.ndo_start_xmit		= emac_dev_xmit,
+	.ndo_set_multicast_list	= emac_dev_mcast_set,
+	.ndo_set_mac_address	= emac_dev_setmac_addr,
+	.ndo_do_ioctl		= emac_devioctl,
+	.ndo_tx_timeout		= emac_dev_tx_timeout,
+	.ndo_get_stats		= emac_dev_getnetstats,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+	.ndo_poll_controller	= emac_poll_controller,
+#endif
+};
+
+/**
+ * davinci_emac_probe: EMAC device probe
+ * @pdev: The DaVinci EMAC device that we are removing
+ *
+ * Called when probing for emac devicesr. We get details of instances and
+ * resource information from platform init and register a network device
+ * and allocate resources necessary for driver to perform
+ */
+static int __devinit davinci_emac_probe(struct platform_device *pdev)
+{
+	int rc = 0;
+	struct resource *res;
+	struct net_device *ndev;
+	struct emac_priv *priv;
+	unsigned long size;
+	struct emac_platform_data *pdata;
+	struct device *emac_dev;
+
+	/* obtain emac clock from kernel */
+	emac_clk = clk_get(&pdev->dev, NULL);
+	if (IS_ERR(emac_clk)) {
+		printk(KERN_ERR "DaVinci EMAC: Failed to get EMAC clock\n");
+		return -EBUSY;
+	}
+	emac_bus_frequency = clk_get_rate(emac_clk);
+	/* TODO: Probe PHY here if possible */
+
+	ndev = alloc_etherdev(sizeof(struct emac_priv));
+	if (!ndev) {
+		printk(KERN_ERR "DaVinci EMAC: Error allocating net_device\n");
+		clk_put(emac_clk);
+		return -ENOMEM;
+	}
+
+	platform_set_drvdata(pdev, ndev);
+	priv = netdev_priv(ndev);
+	priv->pdev = pdev;
+	priv->ndev = ndev;
+	priv->msg_enable = netif_msg_init(debug_level, DAVINCI_EMAC_DEBUG);
+
+	spin_lock_init(&priv->tx_lock);
+	spin_lock_init(&priv->rx_lock);
+	spin_lock_init(&priv->lock);
+
+	pdata = pdev->dev.platform_data;
+	if (!pdata) {
+		printk(KERN_ERR "DaVinci EMAC: No platfrom data\n");
+		return -ENODEV;
+	}
+
+	/* MAC addr and PHY mask , RMII enable info from platform_data */
+	memcpy(priv->mac_addr, pdata->mac_addr, 6);
+	priv->phy_mask = pdata->phy_mask;
+	priv->rmii_en = pdata->rmii_en;
+	priv->version = pdata->version;
+	emac_dev = &ndev->dev;
+	/* Get EMAC platform data */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(emac_dev, "DaVinci EMAC: Error getting res\n");
+		rc = -ENOENT;
+		goto probe_quit;
+	}
+
+	priv->emac_base_phys = res->start + pdata->ctrl_reg_offset;
+	size = res->end - res->start + 1;
+	if (!request_mem_region(res->start, size, ndev->name)) {
+		dev_err(emac_dev, "DaVinci EMAC: failed request_mem_region() \
+					 for regs\n");
+		rc = -ENXIO;
+		goto probe_quit;
+	}
+
+	priv->remap_addr = ioremap(res->start, size);
+	if (!priv->remap_addr) {
+		dev_err(emac_dev, "Unable to map IO\n");
+		rc = -ENOMEM;
+		release_mem_region(res->start, size);
+		goto probe_quit;
+	}
+	priv->emac_base = priv->remap_addr + pdata->ctrl_reg_offset;
+	ndev->base_addr = (unsigned long)priv->remap_addr;
+
+	priv->ctrl_base = priv->remap_addr + pdata->ctrl_mod_reg_offset;
+	priv->ctrl_ram_size = pdata->ctrl_ram_size;
+	priv->emac_ctrl_ram = priv->remap_addr + pdata->ctrl_ram_offset;
+
+	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (!res) {
+		dev_err(emac_dev, "DaVinci EMAC: Error getting irq res\n");
+		rc = -ENOENT;
+		goto no_irq_res;
+	}
+	ndev->irq = res->start;
+
+	if (!is_valid_ether_addr(priv->mac_addr)) {
+		DECLARE_MAC_BUF(buf);
+		/* Use random MAC if none passed */
+		random_ether_addr(priv->mac_addr);
+		printk(KERN_WARNING "%s: using random MAC addr: %s\n",
+			__func__, print_mac(buf, priv->mac_addr));
+	}
+
+	ndev->netdev_ops = &emac_netdev_ops;
+	SET_ETHTOOL_OPS(ndev, &ethtool_ops);
+	netif_napi_add(ndev, &priv->napi, emac_poll, EMAC_POLL_WEIGHT);
+
+	/* register the network device */
+	SET_NETDEV_DEV(ndev, &pdev->dev);
+	rc = register_netdev(ndev);
+	if (rc) {
+		dev_err(emac_dev, "DaVinci EMAC: Error in register_netdev\n");
+		rc = -ENODEV;
+		goto netdev_reg_err;
+	}
+
+	clk_enable(emac_clk);
+
+	/* MII/Phy intialisation, mdio bus registration */
+	emac_mii = mdiobus_alloc();
+	if (emac_mii == NULL) {
+		dev_err(emac_dev, "DaVinci EMAC: Error allocating mii_bus\n");
+		rc = -ENOMEM;
+		goto mdio_alloc_err;
+	}
+
+	priv->mii_bus = emac_mii;
+	emac_mii->name  = "emac-mii",
+	emac_mii->read  = emac_mii_read,
+	emac_mii->write = emac_mii_write,
+	emac_mii->reset = emac_mii_reset,
+	emac_mii->irq   = mii_irqs,
+	emac_mii->phy_mask = ~(priv->phy_mask);
+	emac_mii->parent = &pdev->dev;
+	emac_mii->priv = priv->remap_addr + pdata->mdio_reg_offset;
+	snprintf(priv->mii_bus->id, MII_BUS_ID_SIZE, "%x", priv->pdev->id);
+	mdio_max_freq = pdata->mdio_max_freq;
+	emac_mii->reset(emac_mii);
+
+	/* Register the MII bus */
+	rc = mdiobus_register(emac_mii);
+	if (rc)
+		goto mdiobus_quit;
+
+	if (netif_msg_probe(priv)) {
+		dev_notice(emac_dev, "DaVinci EMAC Probe found device "\
+			   "(regs: %p, irq: %d)\n",
+			   (void *)priv->emac_base_phys, ndev->irq);
+	}
+	return 0;
+
+mdiobus_quit:
+	mdiobus_free(emac_mii);
+
+netdev_reg_err:
+mdio_alloc_err:
+no_irq_res:
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	release_mem_region(res->start, res->end - res->start + 1);
+	iounmap(priv->remap_addr);
+
+probe_quit:
+	clk_put(emac_clk);
+	free_netdev(ndev);
+	return rc;
+}
+
+/**
+ * davinci_emac_remove: EMAC device remove
+ * @pdev: The DaVinci EMAC device that we are removing
+ *
+ * Called when removing the device driver. We disable clock usage and release
+ * the resources taken up by the driver and unregister network device
+ */
+static int __devexit davinci_emac_remove(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct net_device *ndev = platform_get_drvdata(pdev);
+	struct emac_priv *priv = netdev_priv(ndev);
+
+	dev_notice(&ndev->dev, "DaVinci EMAC: davinci_emac_remove()\n");
+
+	clk_disable(emac_clk);
+	platform_set_drvdata(pdev, NULL);
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	mdiobus_unregister(priv->mii_bus);
+	mdiobus_free(priv->mii_bus);
+
+	release_mem_region(res->start, res->end - res->start + 1);
+
+	unregister_netdev(ndev);
+	free_netdev(ndev);
+	iounmap(priv->remap_addr);
+
+	clk_disable(emac_clk);
+	clk_put(emac_clk);
+
+	return 0;
+}
+
+/**
+ * davinci_emac_driver: EMAC platform driver structure
+ *
+ * We implement only probe and remove functions - suspend/resume and
+ * others not supported by this module
+ */
+static struct platform_driver davinci_emac_driver = {
+	.driver = {
+		.name	 = "davinci_emac",
+		.owner	 = THIS_MODULE,
+	},
+	.probe = davinci_emac_probe,
+	.remove = __devexit_p(davinci_emac_remove),
+};
+
+/**
+ * davinci_emac_init: EMAC driver module init
+ *
+ * Called when initializing the driver. We register the driver with
+ * the platform.
+ */
+static int __init davinci_emac_init(void)
+{
+	return platform_driver_register(&davinci_emac_driver);
+}
+module_init(davinci_emac_init);
+
+/**
+ * davinci_emac_exit: EMAC driver module exit
+ *
+ * Called when exiting the driver completely. We unregister the driver with
+ * the platform and exit
+ */
+static void __exit davinci_emac_exit(void)
+{
+	platform_driver_unregister(&davinci_emac_driver);
+}
+module_exit(davinci_emac_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("DaVinci EMAC Maintainer: Anant Gole <anantgole@ti.com>");
+MODULE_AUTHOR("DaVinci EMAC Maintainer: Chaithrika U S <chaithrika@ti.com>");
+MODULE_DESCRIPTION("DaVinci EMAC Ethernet driver");
