diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt
index 34c9528..df09330 100644
--- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt
+++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt
@@ -6,27 +6,10 @@ Practice : Universal Serial Bus" with the following modifications
 and additions :
 
 Required properties :
- - compatible : Should be "nvidia,tegra20-ehci" for USB controllers
-   used in host mode.
- - phy_type : Should be one of "ulpi" or "utmi".
- - nvidia,vbus-gpio : If present, specifies a gpio that needs to be
-   activated for the bus to be powered.
- - nvidia,phy : phandle of the PHY instance, the controller is connected to.
-
-Required properties for phy_type == ulpi:
-  - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
+ - compatible : Should be "nvidia,tegra20-ehci".
+ - nvidia,phy : phandle of the PHY that the controller is connected to.
+ - clocks : Contains a single entry which defines the USB controller's clock.
 
 Optional properties:
-  - dr_mode : dual role mode. Indicates the working mode for
-   nvidia,tegra20-ehci compatible controllers.  Can be "host", "peripheral",
-   or "otg".  Default to "host" if not defined for backward compatibility.
-      host means this is a host controller
-      peripheral means it is device controller
-      otg means it can operate as either ("on the go")
-  - nvidia,has-legacy-mode : boolean indicates whether this controller can
-    operate in legacy mode (as APX 2500 / 2600). In legacy mode some
-    registers are accessed through the APB_MISC base address instead of
-    the USB controller. Since this is a legacy issue it probably does not
-    warrant a compatible string of its own.
-  - nvidia,needs-double-reset : boolean is to be set for some of the Tegra2
-    USB ports, which need reset twice due to hardware issues.
+ - nvidia,needs-double-reset : boolean is to be set for some of the Tegra20
+   USB ports, which need reset twice due to hardware issues.
diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt
index 6bdaba2..6ae8405 100644
--- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt
+++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt
@@ -4,14 +4,47 @@ The device node for Tegra SOC USB PHY:
 
 Required properties :
  - compatible : Should be "nvidia,tegra20-usb-phy".
- - reg : Address and length of the register set for the USB PHY interface.
- - phy_type : Should be one of "ulpi" or "utmi".
+ - reg : Defines the following set of registers, in the order listed:
+   - The PHY's own register set.
+     Always present.
+   - The register set of the PHY containing the UTMI pad control registers.
+     Present if-and-only-if phy_type == utmi.
+ - phy_type : Should be one of "utmi", "ulpi" or "hsic".
+ - clocks : Defines the clocks listed in the clock-names property.
+ - clock-names : The following clock names must be present:
+   - reg: The clock needed to access the PHY's own registers. This is the
+     associated EHCI controller's clock. Always present.
+   - pll_u: PLL_U. Always present.
+   - timer: The timeout clock (clk_m). Present if phy_type == utmi.
+   - utmi-pads: The clock needed to access the UTMI pad control registers.
+     Present if phy_type == utmi.
+   - ulpi-link: The clock Tegra provides to the ULPI PHY (cdev2).
+     Present if phy_type == ulpi, and ULPI link mode is in use.
+  - vbus-supply: regulator for VBUS
 
 Required properties for phy_type == ulpi:
   - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
 
+Required PHY timing params for utmi phy:
+  - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before
+    start of sync launches RxActive
+  - nvidia,elastic-limit : Variable FIFO Depth of elastic input store
+  - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait
+    before declare IDLE.
+  - nvidia,term-range-adj : Range adjusment on terminations
+  - nvidia,xcvr-setup : HS driver output control
+  - nvidia,xcvr-lsfslew : LS falling slew rate control.
+  - nvidia,xcvr-lsrslew :  LS rising slew rate control.
+
 Optional properties:
   - nvidia,has-legacy-mode : boolean indicates whether this controller can
     operate in legacy mode (as APX 2500 / 2600). In legacy mode some
     registers are accessed through the APB_MISC base address instead of
-    the USB controller.
\ No newline at end of file
+    the USB controller.
+  - dr_mode : dual role mode. Indicates the working mode for the PHY. Can be
+    "host", "peripheral", or "otg". Defaults to "host" if not defined.
+      host means this is a host controller
+      peripheral means it is device controller
+      otg means it can operate as either ("on the go")
+  - nvidia,is-wired : boolean. Indicates whether we can do certain kind of power
+    optimizations for the devices that are always connected. e.g. modem.
