@@ -370,8 +370,6 @@ struct igb_adapter {
u32 eims_other;
/* to not mess up cache alignment, always add to the bottom */
- u32 eeprom_wol;
-
u16 tx_ring_count;
u16 rx_ring_count;
unsigned int vfs_allocated_count;
@@ -401,6 +399,7 @@ struct igb_adapter {
#define IGB_FLAG_PTP (1 << 5)
#define IGB_FLAG_RSS_FIELD_IPV4_UDP (1 << 6)
#define IGB_FLAG_RSS_FIELD_IPV6_UDP (1 << 7)
+#define IGB_FLAG_WOL_SUPPORTED (1 << 8)
/* DMA Coalescing defines */
#define IGB_MIN_TXPBSIZE 20408
@@ -1966,54 +1966,6 @@ static void igb_diag_test(struct net_device *netdev,
msleep_interruptible(4 * 1000);
}
-static int igb_wol_exclusion(struct igb_adapter *adapter,
- struct ethtool_wolinfo *wol)
-{
- struct e1000_hw *hw = &adapter->hw;
- int retval = 1; /* fail by default */
-
- switch (hw->device_id) {
- case E1000_DEV_ID_82575GB_QUAD_COPPER:
- /* WoL not supported */
- wol->supported = 0;
- break;
- case E1000_DEV_ID_82575EB_FIBER_SERDES:
- case E1000_DEV_ID_82576_FIBER:
- case E1000_DEV_ID_82576_SERDES:
- /* Wake events not supported on port B */
- if (rd32(E1000_STATUS) & E1000_STATUS_FUNC_1) {
- wol->supported = 0;
- break;
- }
- /* return success for non excluded adapter ports */
- retval = 0;
- break;
- case E1000_DEV_ID_82576_QUAD_COPPER:
- case E1000_DEV_ID_82576_QUAD_COPPER_ET2:
- /* quad port adapters only support WoL on port A */
- if (!(adapter->flags & IGB_FLAG_QUAD_PORT_A)) {
- wol->supported = 0;
- break;
- }
- /* return success for non excluded adapter ports */
- retval = 0;
- break;
- default:
- /* dual port cards only support WoL on port A from now on
- * unless it was enabled in the eeprom for port B
- * so exclude FUNC_1 ports from having WoL enabled */
- if ((rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) &&
- !adapter->eeprom_wol) {
- wol->supported = 0;
- break;
- }
-
- retval = 0;
- }
-
- return retval;
-}
-
static void igb_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
{
struct igb_adapter *adapter = netdev_priv(netdev);
@@ -2023,10 +1975,7 @@ static void igb_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
WAKE_PHY;
wol->wolopts = 0;
- /* this function will set ->supported = 0 and return 1 if wol is not
- * supported by this hardware */
- if (igb_wol_exclusion(adapter, wol) ||
- !device_can_wakeup(&adapter->pdev->dev))
+ if (!(adapter->flags & IGB_FLAG_WOL_SUPPORTED))
return;
/* apply any specific unsupported masks here */
@@ -2054,8 +2003,7 @@ static int igb_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
if (wol->wolopts & (WAKE_ARP | WAKE_MAGICSECURE))
return -EOPNOTSUPP;
- if (igb_wol_exclusion(adapter, wol) ||
- !device_can_wakeup(&adapter->pdev->dev))
+ if (!(adapter->flags & IGB_FLAG_WOL_SUPPORTED))
return wol->wolopts ? -EOPNOTSUPP : 0;
/* these settings will always override what we currently have */
@@ -1837,7 +1837,6 @@ static int __devinit igb_probe(struct pci_dev *pdev,
const struct e1000_info *ei = igb_info_tbl[ent->driver_data];
unsigned long mmio_start, mmio_len;
int err, pci_using_dac;
- u16 eeprom_apme_mask = IGB_EEPROM_APME;
u8 part_str[E1000_PBANUM_LENGTH];
/* Catch broken hardware that put the wrong VF device ID in
@@ -2045,28 +2044,27 @@ static int __devinit igb_probe(struct pci_dev *pdev,
igb_validate_mdi_setting(hw);
- /* Initial Wake on LAN setting If APM wake is enabled in the EEPROM,
- * enable the ACPI Magic Packet filter
- */
-
+ /* By default, support wake on port A */
if (hw->bus.func == 0)
- hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
- else if (hw->mac.type >= e1000_82580)
+ adapter->flags |= IGB_FLAG_WOL_SUPPORTED;
+
+ /* Check the NVM for wake support on non-port A ports */
+ if (hw->mac.type >= e1000_82580)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A +
NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1,
&eeprom_data);
else if (hw->bus.func == 1)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
- if (eeprom_data & eeprom_apme_mask)
- adapter->eeprom_wol |= E1000_WUFC_MAG;
+ if (eeprom_data & IGB_EEPROM_APME)
+ adapter->flags |= IGB_FLAG_WOL_SUPPORTED;
/* now that we have the eeprom settings, apply the special cases where
* the eeprom may be wrong or the board simply won't support wake on
* lan on a particular port */
switch (pdev->device) {
case E1000_DEV_ID_82575GB_QUAD_COPPER:
- adapter->eeprom_wol = 0;
+ adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED;
break;
case E1000_DEV_ID_82575EB_FIBER_SERDES:
case E1000_DEV_ID_82576_FIBER:
@@ -2074,24 +2072,38 @@ static int __devinit igb_probe(struct pci_dev *pdev,
/* Wake events only supported on port A for dual fiber
* regardless of eeprom setting */
if (rd32(E1000_STATUS) & E1000_STATUS_FUNC_1)
- adapter->eeprom_wol = 0;
+ adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED;
break;
case E1000_DEV_ID_82576_QUAD_COPPER:
case E1000_DEV_ID_82576_QUAD_COPPER_ET2:
/* if quad port adapter, disable WoL on all but port A */
if (global_quad_port_a != 0)
- adapter->eeprom_wol = 0;
+ adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED;
else
adapter->flags |= IGB_FLAG_QUAD_PORT_A;
/* Reset for multiple quad port adapters */
if (++global_quad_port_a == 4)
global_quad_port_a = 0;
break;
+ default:
+ /* If the device can't wake, don't set software support */
+ if (!device_can_wakeup(&adapter->pdev->dev))
+ adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED;
}
/* initialize the wol settings based on the eeprom settings */
- adapter->wol = adapter->eeprom_wol;
- device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
+ if (adapter->flags & IGB_FLAG_WOL_SUPPORTED)
+ adapter->wol |= E1000_WUFC_MAG;
+
+ /* Some vendors want WoL disabled by default, but still supported */
+ if ((hw->mac.type == e1000_i350) &&
+ (pdev->subsystem_vendor == PCI_VENDOR_ID_HP)) {
+ adapter->flags |= IGB_FLAG_WOL_SUPPORTED;
+ adapter->wol = 0;
+ }
+
+ device_set_wakeup_enable(&adapter->pdev->dev,
+ adapter->flags & IGB_FLAG_WOL_SUPPORTED);
/* reset the hardware with the new settings */
igb_reset(adapter);