diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt deleted file mode 100644 index 4746452..0000000 --- a/Documentation/devicetree/bindings/arm/davinci/nand.txt +++ /dev/null @@ -1,59 +0,0 @@ -* Texas Instruments Davinci NAND - -This file provides information, what the device node for the -davinci nand interface contain. - -Required properties: -- compatible: "ti,davinci-nand"; -- reg : contain 2 offset/length values: - - offset and length for the access window - - offset and length for accessing the aemif control registers -- ti,davinci-chipselect: Indicates on the davinci_nand driver which - chipselect is used for accessing the nand. - -Recommended properties : -- ti,davinci-mask-ale: mask for ale -- ti,davinci-mask-cle: mask for cle -- ti,davinci-mask-chipsel: mask for chipselect -- ti,davinci-ecc-mode: ECC mode valid values for davinci driver: - - "none" - - "soft" - - "hw" -- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4. -- ti,davinci-nand-buswidth: buswidth 8 or 16 -- ti,davinci-nand-use-bbt: use flash based bad block table support. - -nand device bindings may contain additional sub-nodes describing -partitions of the address space. See partition.txt for more detail. - -Example (enbw_cmc board): -aemif@60000000 { - compatible = "ti,davinci-aemif"; - #address-cells = <2>; - #size-cells = <1>; - reg = <0x68000000 0x80000>; - ranges = <2 0 0x60000000 0x02000000 - 3 0 0x62000000 0x02000000 - 4 0 0x64000000 0x02000000 - 5 0 0x66000000 0x02000000 - 6 0 0x68000000 0x02000000>; - nand@3,0 { - compatible = "ti,davinci-nand"; - reg = <3 0x0 0x807ff - 6 0x0 0x8000>; - #address-cells = <1>; - #size-cells = <1>; - ti,davinci-chipselect = <1>; - ti,davinci-mask-ale = <0>; - ti,davinci-mask-cle = <0>; - ti,davinci-mask-chipsel = <0>; - ti,davinci-ecc-mode = "hw"; - ti,davinci-ecc-bits = <4>; - ti,davinci-nand-use-bbt; - - partition@180000 { - label = "ubifs"; - reg = <0x180000 0x7e80000>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/mtd/davinci-nand.txt b/Documentation/devicetree/bindings/mtd/davinci-nand.txt new file mode 100644 index 0000000..4746452 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/davinci-nand.txt @@ -0,0 +1,59 @@ +* Texas Instruments Davinci NAND + +This file provides information, what the device node for the +davinci nand interface contain. + +Required properties: +- compatible: "ti,davinci-nand"; +- reg : contain 2 offset/length values: + - offset and length for the access window + - offset and length for accessing the aemif control registers +- ti,davinci-chipselect: Indicates on the davinci_nand driver which + chipselect is used for accessing the nand. + +Recommended properties : +- ti,davinci-mask-ale: mask for ale +- ti,davinci-mask-cle: mask for cle +- ti,davinci-mask-chipsel: mask for chipselect +- ti,davinci-ecc-mode: ECC mode valid values for davinci driver: + - "none" + - "soft" + - "hw" +- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4. +- ti,davinci-nand-buswidth: buswidth 8 or 16 +- ti,davinci-nand-use-bbt: use flash based bad block table support. + +nand device bindings may contain additional sub-nodes describing +partitions of the address space. See partition.txt for more detail. + +Example (enbw_cmc board): +aemif@60000000 { + compatible = "ti,davinci-aemif"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0x68000000 0x80000>; + ranges = <2 0 0x60000000 0x02000000 + 3 0 0x62000000 0x02000000 + 4 0 0x64000000 0x02000000 + 5 0 0x66000000 0x02000000 + 6 0 0x68000000 0x02000000>; + nand@3,0 { + compatible = "ti,davinci-nand"; + reg = <3 0x0 0x807ff + 6 0x0 0x8000>; + #address-cells = <1>; + #size-cells = <1>; + ti,davinci-chipselect = <1>; + ti,davinci-mask-ale = <0>; + ti,davinci-mask-cle = <0>; + ti,davinci-mask-chipsel = <0>; + ti,davinci-ecc-mode = "hw"; + ti,davinci-ecc-bits = <4>; + ti,davinci-nand-use-bbt; + + partition@180000 { + label = "ubifs"; + reg = <0x180000 0x7e80000>; + }; + }; +}; diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 8ca4176..390cc95 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -569,11 +569,11 @@ config MTD_NAND_SH_FLCTL for NAND Flash using FLCTL. config MTD_NAND_DAVINCI - tristate "Support NAND on DaVinci SoC" - depends on ARCH_DAVINCI + tristate "Support NAND on SoCs with AEMIF" + select TI_DAVINCI_AEMIF help Enable the driver for NAND flash chips on Texas Instruments - DaVinci processors. + SoCs that has Asynchronous External Memory Interface (AEMIF). config MTD_NAND_TXX9NDFMC tristate "NAND Flash support for TXx9 SoC" diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c index 321b053..306959e 100644 --- a/drivers/mtd/nand/davinci_nand.c +++ b/drivers/mtd/nand/davinci_nand.c @@ -35,8 +35,8 @@ #include #include -#include -#include +#include +#include /* * This is a device driver for the NAND flash controller found on the @@ -73,7 +73,7 @@ struct davinci_nand_info { uint32_t core_chipsel; - struct davinci_aemif_timing *timing; + struct davinci_aemif_cs_data *cs_data; }; static DEFINE_SPINLOCK(davinci_nand_lock); @@ -652,7 +652,6 @@ static int __init nand_davinci_probe(struct platform_device *pdev) info->chip.options = pdata->options; info->chip.bbt_td = pdata->bbt_td; info->chip.bbt_md = pdata->bbt_md; - info->timing = pdata->timing; info->ioaddr = (uint32_t __force) vaddr; @@ -731,26 +730,21 @@ static int __init nand_davinci_probe(struct platform_device *pdev) goto err_clk_enable; } - /* - * Setup Async configuration register in case we did not boot from - * NAND and so bootloader did not bother to set it up. - */ - val = davinci_nand_readl(info, A1CR_OFFSET + info->core_chipsel * 4); - - /* Extended Wait is not valid and Select Strobe mode is not used */ - val &= ~(ACR_ASIZE_MASK | ACR_EW_MASK | ACR_SS_MASK); - if (info->chip.options & NAND_BUSWIDTH_16) - val |= 0x1; + if (info->chip.options & NAND_BUSWIDTH_16) { + info->cs_data = + davinci_aemif_get_abus_params(info->core_chipsel); + if (info->cs_data == NULL) + goto err_bus_config; - davinci_nand_writel(info, A1CR_OFFSET + info->core_chipsel * 4, val); + /* asize = 1 for 16bit bus */ + info->cs_data->asize = 1; + ret = davinci_aemif_set_abus_params(info->core_chipsel, + info->cs_data); - ret = 0; - if (info->timing) - ret = davinci_aemif_setup_timing(info->timing, info->base, - info->core_chipsel); - if (ret < 0) { - dev_dbg(&pdev->dev, "NAND timing values setup fail\n"); - goto err_timing; + if (ret < 0) { + dev_dbg(&pdev->dev, "NAND timing values setup fail\n"); + goto err_bus_config; + } } spin_lock_irq(&davinci_nand_lock); @@ -841,7 +835,7 @@ syndrome_done: return 0; err_scan: -err_timing: +err_bus_config: clk_disable_unprepare(info->clk); err_clk_enable: diff --git a/include/linux/platform_data/davinci-nand.h b/include/linux/platform_data/davinci-nand.h new file mode 100644 index 0000000..df1fc66 --- /dev/null +++ b/include/linux/platform_data/davinci-nand.h @@ -0,0 +1,87 @@ +/* + * mach-davinci/nand.h + * + * Copyright © 2006 Texas Instruments. + * + * Ported to 2.6.23 Copyright © 2008 by + * Sander Huijsen + * Troy Kisky + * Dirk Behme + * + * -------------------------------------------------------------------------- + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef __ARCH_ARM_DAVINCI_NAND_H +#define __ARCH_ARM_DAVINCI_NAND_H + +#include + +#define NANDFCR_OFFSET 0x60 +#define NANDFSR_OFFSET 0x64 +#define NANDF1ECC_OFFSET 0x70 + +/* 4-bit ECC syndrome registers */ +#define NAND_4BIT_ECC_LOAD_OFFSET 0xbc +#define NAND_4BIT_ECC1_OFFSET 0xc0 +#define NAND_4BIT_ECC2_OFFSET 0xc4 +#define NAND_4BIT_ECC3_OFFSET 0xc8 +#define NAND_4BIT_ECC4_OFFSET 0xcc +#define NAND_ERR_ADD1_OFFSET 0xd0 +#define NAND_ERR_ADD2_OFFSET 0xd4 +#define NAND_ERR_ERRVAL1_OFFSET 0xd8 +#define NAND_ERR_ERRVAL2_OFFSET 0xdc + +/* NOTE: boards don't need to use these address bits + * for ALE/CLE unless they support booting from NAND. + * They're used unless platform data overrides them. + */ +#define MASK_ALE 0x08 +#define MASK_CLE 0x10 + +struct davinci_nand_pdata { /* platform_data */ + uint32_t mask_ale; + uint32_t mask_cle; + + /* for packages using two chipselects */ + uint32_t mask_chipsel; + + /* board's default static partition info */ + struct mtd_partition *parts; + unsigned nr_parts; + + /* none == NAND_ECC_NONE (strongly *not* advised!!) + * soft == NAND_ECC_SOFT + * else == NAND_ECC_HW, according to ecc_bits + * + * All DaVinci-family chips support 1-bit hardware ECC. + * Newer ones also support 4-bit ECC, but are awkward + * using it with large page chips. + */ + nand_ecc_modes_t ecc_mode; + u8 ecc_bits; + + /* e.g. NAND_BUSWIDTH_16 */ + unsigned options; + /* e.g. NAND_BBT_USE_FLASH */ + unsigned bbt_options; + + /* Main and mirror bbt descriptor overrides */ + struct nand_bbt_descr *bbt_td; + struct nand_bbt_descr *bbt_md; +}; + +#endif /* __ARCH_ARM_DAVINCI_NAND_H */