Patchwork [U-Boot,22/28] powerpc/mpc85xx: software workaround for DDR erratum A-004468

login
register
mail settings
Submitter York Sun
Date Oct. 8, 2012, 5:44 p.m.
Message ID <1349718271-26503-22-git-send-email-yorksun@freescale.com>
Download mbox | patch
Permalink /patch/190089/
State Accepted, archived
Delegated to: Andy Fleming
Headers show

Comments

York Sun - Oct. 8, 2012, 5:44 p.m.
Boot space translation utilizes the pre-translation address to select
the DDR controller target. However, the post-translation address will be
presented to the selected DDR controller. It is possible that the pre-
translation address selects one DDR controller but the post-translation
address exists in a different DDR controller when using certain DDR
controller interleaving modes. The device may fail to boot under these
circumstances. Note that a DDR MSE error will not be detected since DDR
controller bounds registers are programmed to be the same when configured
for DDR controller interleaving.

Signed-off-by: York Sun <yorksun@freescale.com>
---
 arch/powerpc/cpu/mpc85xx/cmd_errata.c     |    3 +
 arch/powerpc/cpu/mpc85xx/fdt.c            |    2 +-
 arch/powerpc/cpu/mpc85xx/mp.c             |   96 ++++++++++++++++++++++++++---
 arch/powerpc/cpu/mpc86xx/fdt.c            |    2 +-
 arch/powerpc/cpu/mpc86xx/mp.c             |    9 ++-
 arch/powerpc/cpu/mpc8xxx/ddr/util.c       |   10 +++
 arch/powerpc/include/asm/config_mpc85xx.h |    1 +
 arch/powerpc/include/asm/mp.h             |    2 +-
 arch/powerpc/lib/board.c                  |    4 +-
 9 files changed, 111 insertions(+), 18 deletions(-)

Patch

diff --git a/arch/powerpc/cpu/mpc85xx/cmd_errata.c b/arch/powerpc/cpu/mpc85xx/cmd_errata.c
index e8989bd..67508ff 100644
--- a/arch/powerpc/cpu/mpc85xx/cmd_errata.c
+++ b/arch/powerpc/cpu/mpc85xx/cmd_errata.c
@@ -76,6 +76,9 @@  static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 #if defined(CONFIG_SYS_FSL_ERRATUM_ESDHC111)
 	puts("Work-around for Erratum ESDHC111 enabled\n");
 #endif
+#ifdef CONFIG_SYS_FSL_ERRATUM_A004468
+	puts("Work-around for Erratum A004468 enabled\n");
+#endif
 #if defined(CONFIG_SYS_FSL_ERRATUM_ESDHC135)
 	puts("Work-around for Erratum ESDHC135 enabled\n");
 #endif
diff --git a/arch/powerpc/cpu/mpc85xx/fdt.c b/arch/powerpc/cpu/mpc85xx/fdt.c
index d54527a..8221481 100644
--- a/arch/powerpc/cpu/mpc85xx/fdt.c
+++ b/arch/powerpc/cpu/mpc85xx/fdt.c
@@ -48,7 +48,7 @@  void ft_fixup_cpu(void *blob, u64 memory_limit)
 {
 	int off;
 	ulong spin_tbl_addr = get_spin_phys_addr();
-	u32 bootpg = determine_mp_bootpg();
+	u32 bootpg = determine_mp_bootpg(NULL);
 	u32 id = get_my_id();
 	const char *enable_method;
 
diff --git a/arch/powerpc/cpu/mpc85xx/mp.c b/arch/powerpc/cpu/mpc85xx/mp.c
index ffc2a9a..39adf8e 100644
--- a/arch/powerpc/cpu/mpc85xx/mp.c
+++ b/arch/powerpc/cpu/mpc85xx/mp.c
@@ -27,9 +27,11 @@ 
 #include <asm/io.h>
 #include <asm/mmu.h>
 #include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
 #include "mp.h"
 
 DECLARE_GLOBAL_DATA_PTR;
+u32 fsl_ddr_get_intl3r(void);
 
 u32 get_my_id()
 {
@@ -191,13 +193,68 @@  int cpu_release(int nr, int argc, char * const argv[])
 	return 0;
 }
 
-u32 determine_mp_bootpg(void)
+u32 determine_mp_bootpg(unsigned int *pagesize)
 {
+	u32 bootpg;
+#ifdef CONFIG_SYS_FSL_ERRATUM_A004468
+	u32 svr = get_svr();
+	u32 granule_size, check;
+	struct law_entry e;
+#endif
+
 	/* if we have 4G or more of memory, put the boot page at 4Gb-4k */
 	if ((u64)gd->ram_size > 0xfffff000)
-		return (0xfffff000);
+		bootpg = 0xfffff000;
+	else
+		bootpg = gd->ram_size - 4096;
+	if (pagesize)
+		*pagesize = 4096;
+
+#ifdef CONFIG_SYS_FSL_ERRATUM_A004468
+/*
+ * Erratum A004468 has two parts. The 3-way interleaving applies to T4240,
+ * to be fixed in rev 2.0. The 2-way interleaving applies to many SoCs. But
+ * the way boot page chosen in u-boot avoids hitting this erratum. So only
+ * thw workaround for 3-way interleaving is needed.
+ *
+ * To make sure boot page translation works with 3-Way DDR interleaving
+ * enforce a check for the following constrains
+ * 8K granule size requires BRSIZE=8K and
+ *    bootpg >> log2(BRSIZE) %3 == 1
+ * 4K and 1K granule size requires BRSIZE=4K and
+ *    bootpg >> log2(BRSIZE) %3 == 0
+ */
+	if (SVR_SOC_VER(svr) == SVR_T4240 && SVR_MAJ(svr) < 2) {
+		e = find_law(bootpg);
+		switch (e.trgt_id) {
+		case LAW_TRGT_IF_DDR_INTLV_123:
+			granule_size = fsl_ddr_get_intl3r() & 0x1f;
+			if (granule_size == FSL_DDR_3WAY_8KB_INTERLEAVING) {
+				if (pagesize)
+					*pagesize = 8192;
+				bootpg &= 0xffffe000;	/* align to 8KB */
+				check = bootpg >> 13;
+				while ((check % 3) != 1)
+					check--;
+				bootpg = check << 13;
+				debug("Boot page (8K) at 0x%08x\n", bootpg);
+				break;
+			} else {
+				bootpg &= 0xfffff000;	/* align to 4KB */
+				check = bootpg >> 12;
+				while ((check % 3) != 0)
+					check--;
+				bootpg = check << 12;
+				debug("Boot page (4K) at 0x%08x\n", bootpg);
+			}
+				break;
+		default:
+			break;
+		}
+	}
+#endif /* CONFIG_SYS_FSL_ERRATUM_A004468 */
 
-	return (gd->ram_size - 4096);
+	return bootpg;
 }
 
 ulong get_spin_phys_addr(void)
@@ -219,9 +276,9 @@  ulong get_spin_virt_addr(void)
 }
 
 #ifdef CONFIG_FSL_CORENET
-static void plat_mp_up(unsigned long bootpg)
+static void plat_mp_up(unsigned long bootpg, unsigned int pagesize)
 {
-	u32 cpu_up_mask, whoami;
+	u32 cpu_up_mask, whoami, brsize = LAW_SIZE_4K;
 	u32 *table = (u32 *)get_spin_virt_addr();
 	volatile ccsr_gur_t *gur;
 	volatile ccsr_local_t *ccm;
@@ -241,7 +298,11 @@  static void plat_mp_up(unsigned long bootpg)
 	out_be32(&ccm->bstrl, bootpg);
 
 	e = find_law(bootpg);
-	out_be32(&ccm->bstrar, LAW_EN | e.trgt_id << 20 | LAW_SIZE_4K);
+	/* pagesize is only 4K or 8K */
+	if (pagesize == 8192)
+		brsize = LAW_SIZE_8K;
+	out_be32(&ccm->bstrar, LAW_EN | e.trgt_id << 20 | brsize);
+	debug("BRSIZE is 0x%x\n", brsize);
 
 	/* readback to sync write */
 	in_be32(&ccm->bstrar);
@@ -294,7 +355,7 @@  static void plat_mp_up(unsigned long bootpg)
 #endif
 }
 #else
-static void plat_mp_up(unsigned long bootpg)
+static void plat_mp_up(unsigned long bootpg, unsigned int pagesize)
 {
 	u32 up, cpu_up_mask, whoami;
 	u32 *table = (u32 *)get_spin_virt_addr();
@@ -374,7 +435,7 @@  static void plat_mp_up(unsigned long bootpg)
 
 void cpu_mp_lmb_reserve(struct lmb *lmb)
 {
-	u32 bootpg = determine_mp_bootpg();
+	u32 bootpg = determine_mp_bootpg(NULL);
 
 	lmb_reserve(lmb, bootpg, 4096);
 }
@@ -383,8 +444,23 @@  void setup_mp(void)
 {
 	extern ulong __secondary_start_page;
 	extern ulong __bootpg_addr;
+
 	ulong fixup = (ulong)&__secondary_start_page;
-	u32 bootpg = determine_mp_bootpg();
+	u32 bootpg, bootpg_map, pagesize;
+
+	bootpg = determine_mp_bootpg(&pagesize);
+
+	/*
+	 * pagesize is only 4K or 8K
+	 * we only use the last 4K of boot page
+	 * bootpg_map saves the address for the boot page
+	 * 8K is used for the workaround of 3-way DDR interleaving
+	 */
+
+	bootpg_map = bootpg;
+
+	if (pagesize == 8192)
+		bootpg += 4096;	/* use 2nd half */
 
 	/* Some OSes expect secondary cores to be held in reset */
 	if (hold_cores_in_reset(0))
@@ -407,7 +483,7 @@  void setup_mp(void)
 
 		memcpy((void *)CONFIG_BPTR_VIRT_ADDR, (void *)fixup, 4096);
 
-		plat_mp_up(bootpg);
+		plat_mp_up(bootpg_map, pagesize);
 	} else {
 		puts("WARNING: No reset page TLB. "
 			"Skipping secondary core setup\n");
diff --git a/arch/powerpc/cpu/mpc86xx/fdt.c b/arch/powerpc/cpu/mpc86xx/fdt.c
index 61f5110..2f955fe 100644
--- a/arch/powerpc/cpu/mpc86xx/fdt.c
+++ b/arch/powerpc/cpu/mpc86xx/fdt.c
@@ -20,7 +20,7 @@  void ft_cpu_setup(void *blob, bd_t *bd)
 {
 #ifdef CONFIG_MP
 	int off;
-	u32 bootpg = determine_mp_bootpg();
+	u32 bootpg = determine_mp_bootpg(NULL);
 #endif
 
 	do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
diff --git a/arch/powerpc/cpu/mpc86xx/mp.c b/arch/powerpc/cpu/mpc86xx/mp.c
index 30c99eb..de705f0 100644
--- a/arch/powerpc/cpu/mpc86xx/mp.c
+++ b/arch/powerpc/cpu/mpc86xx/mp.c
@@ -90,8 +90,11 @@  int cpu_release(int nr, int argc, char * const argv[])
 	return 1;
 }
 
-u32 determine_mp_bootpg(void)
+u32 determine_mp_bootpg(unsigned int *pagesize)
 {
+	if (pagesize)
+		*pagesize = 4096;
+
 	/* if we have 4G or more of memory, put the boot page at 4Gb-1M */
 	if ((u64)gd->ram_size > 0xfffff000)
 		return (0xfff00000);
@@ -101,7 +104,7 @@  u32 determine_mp_bootpg(void)
 
 void cpu_mp_lmb_reserve(struct lmb *lmb)
 {
-	u32 bootpg = determine_mp_bootpg();
+	u32 bootpg = determine_mp_bootpg(NULL);
 
 	/* tell u-boot we stole a page */
 	lmb_reserve(lmb, bootpg, 4096);
@@ -115,7 +118,7 @@  void setup_mp(void)
 {
 	extern ulong __secondary_start_page;
 	ulong fixup = (ulong)&__secondary_start_page;
-	u32 bootpg = determine_mp_bootpg();
+	u32 bootpg = determine_mp_bootpg(NULL);
 	u32 bootpg_va;
 
 	if (bootpg >= CONFIG_SYS_MAX_DDR_BAT_SIZE) {
diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/util.c b/arch/powerpc/cpu/mpc8xxx/ddr/util.c
index afc5fae..940ffff 100644
--- a/arch/powerpc/cpu/mpc8xxx/ddr/util.c
+++ b/arch/powerpc/cpu/mpc8xxx/ddr/util.c
@@ -121,6 +121,16 @@  void fsl_ddr_set_intl3r(const unsigned int granule_size)
 #endif
 }
 
+u32 fsl_ddr_get_intl3r(void)
+{
+	u32 val = 0;
+#ifdef CONFIG_E6500
+	u32 *mcintl3r = (void *) (CONFIG_SYS_IMMR + 0x18004);
+	val = *mcintl3r;
+#endif
+	return val;
+}
+
 void board_add_ram_info(int use_default)
 {
 #if defined(CONFIG_MPC83xx)
diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h
index 65c82bb..225d620 100644
--- a/arch/powerpc/include/asm/config_mpc85xx.h
+++ b/arch/powerpc/include/asm/config_mpc85xx.h
@@ -478,6 +478,7 @@ 
 #define CONFIG_SYS_FSL_USB1_PHY_ENABLE
 #define CONFIG_SYS_FSL_USB2_PHY_ENABLE
 #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
+#define CONFIG_SYS_FSL_ERRATUM_A004468
 #define CONFIG_SYS_CCSRBAR_DEFAULT	0xfe000000
 
 #elif defined(CONFIG_PPC_B4860)
diff --git a/arch/powerpc/include/asm/mp.h b/arch/powerpc/include/asm/mp.h
index fe490ba..9188ede 100644
--- a/arch/powerpc/include/asm/mp.h
+++ b/arch/powerpc/include/asm/mp.h
@@ -25,7 +25,7 @@ 
 
 void setup_mp(void);
 void cpu_mp_lmb_reserve(struct lmb *lmb);
-u32 determine_mp_bootpg(void);
+u32 determine_mp_bootpg(unsigned int *pagesize);
 int is_core_disabled(int nr);
 
 #ifdef CONFIG_E6500
diff --git a/arch/powerpc/lib/board.c b/arch/powerpc/lib/board.c
index 07feaf5..2f35bda 100644
--- a/arch/powerpc/lib/board.c
+++ b/arch/powerpc/lib/board.c
@@ -440,8 +440,8 @@  void board_init_f(ulong bootflag)
 	 * We need to make sure the location we intend to put secondary core
 	 * boot code is reserved and not used by any part of u-boot
 	 */
-	if (addr > determine_mp_bootpg()) {
-		addr = determine_mp_bootpg();
+	if (addr > determine_mp_bootpg(NULL)) {
+		addr = determine_mp_bootpg(NULL);
 		debug("Reserving MP boot page to %08lx\n", addr);
 	}
 #endif