diff mbox

Powerpc 8xx CPM_UART setting MAXIDL register proportionaly to baud rate

Message ID 201209240639.q8O6di6f029596@localhost.localdomain (mailing list archive)
State Accepted, archived
Headers show

Commit Message

Christophe Leroy Sept. 24, 2012, 6:39 a.m. UTC 
MAXIDL is the timeout after which a receive buffer is closed when not full if
no more characters are received. We calculate it from the baudrate so that the
duration is always the same at standard rates: about 4ms. At 9600 bauds it gives
a timeout of 4 characters, which is the timeout on the 8250 UART.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>

Comments

Alan Cox Sept. 24, 2012, 1:21 p.m. UTC | #1 
On Mon, 24 Sep 2012 08:39:44 +0200
Christophe Leroy <christophe.leroy@c-s.fr> wrote:

> MAXIDL is the timeout after which a receive buffer is closed when not
> full if no more characters are received. We calculate it from the
> baudrate so that the duration is always the same at standard rates:
> about 4ms. At 9600 bauds it gives a timeout of 4 characters, which is
> the timeout on the 8250 UART.
> 
> Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>

Looks good tome - series Acked-by: Alan Cox <alan@linux.intel.com>
diff mbox

Patch

--- linux-3.5-vanilla/drivers/tty/serial/cpm_uart/cpm_uart_core.c	2012-07-21 22:58:29.000000000 +0200
+++ linux-3.5/drivers/tty/serial/cpm_uart/cpm_uart_core.c	2012-08-09 17:38:37.000000000 +0200
@@ -501,6 +501,7 @@ 
 	struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
 	smc_t __iomem *smcp = pinfo->smcp;
 	scc_t __iomem *sccp = pinfo->sccp;
+	int maxidl;
 
 	pr_debug("CPM uart[%d]:set_termios\n", port->line);
 
@@ -511,6 +512,17 @@ 
 	else
 		pinfo->rx_fifosize = RX_BUF_SIZE;
 
+	/* MAXIDL is the timeout after which a receive buffer is closed
+	 * when not full if no more characters are received.
+	 * We calculate it from the baudrate so that the duration is
+	 * always the same at standard rates: about 4ms.
+	 */
+	maxidl = baud / 2400;
+	if (maxidl < 1)
+		maxidl = 1;
+	if (maxidl > 0x10)
+		maxidl = 0x10;
+
 	/* Character length programmed into the mode register is the
 	 * sum of: 1 start bit, number of data bits, 0 or 1 parity bit,
 	 * 1 or 2 stop bits, minus 1.
@@ -611,6 +623,7 @@ 
 		 * SMC/SCC receiver is disabled.
 		 */
 		out_be16(&pinfo->smcup->smc_mrblr, pinfo->rx_fifosize);
+		out_be16(&pinfo->smcup->smc_maxidl, maxidl);
 
 		/* Set the mode register.  We want to keep a copy of the
 		 * enables, because we want to put them back if they were
@@ -623,6 +636,7 @@ 
 		    SMCMR_SM_UART | prev_mode);
 	} else {
 		out_be16(&pinfo->sccup->scc_genscc.scc_mrblr, pinfo->rx_fifosize);
+		out_be16(&pinfo->sccup->scc_maxidl, maxidl);
 		out_be16(&sccp->scc_psmr, (sbits << 12) | scval);
 	}