@@ -23,6 +23,7 @@
*/
#include <common.h>
+#include <lcd.h>
#include <asm/io.h>
#include <spi.h>
#include <asm/arch/adc.h>
@@ -34,6 +35,8 @@
#include <asm/arch/cpu.h>
#include <max8998_pmic.h>
#include <asm/arch/watchdog.h>
+#include <libtizen.h>
+#include <ld9040.h>
#if defined(CONFIG_SOFT_SPI)
# include <asm/gpio.h>
#endif
@@ -56,24 +59,6 @@ static int get_hwrev(void)
static void check_hw_revision(void);
-int board_init(void)
-{
- gpio1 = (struct exynos4_gpio_part1 *) EXYNOS4_GPIO_PART1_BASE;
- gpio2 = (struct exynos4_gpio_part2 *) EXYNOS4_GPIO_PART2_BASE;
-
- gd->bd->bi_arch_number = MACH_TYPE_UNIVERSAL_C210;
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
-#if defined(CONFIG_PMIC)
- pmic_init();
-#endif
-
- check_hw_revision();
- printf("HW Revision:\t0x%x\n", board_rev);
-
- return 0;
-}
-
int dram_init(void)
{
gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) +
@@ -323,3 +308,183 @@ int spi_cs_is_valid(unsigned int bus, unsigned int cs)
return bus == 0 && cs == 0;
}
+static void init_pmic_lcd(void)
+{
+ unsigned char val;
+ int ret = 0;
+
+ struct pmic *p = get_pmic();
+
+ if (pmic_probe(p))
+ return;
+
+ /* LDO7 1.8V */
+ val = 0x02; /* (1800 - 1600) / 100; */
+ ret |= pmic_reg_write(p, MAX8998_REG_LDO7, val);
+
+ /* LDO17 3.0V */
+ val = 0xe; /* (3000 - 1600) / 100; */
+ ret |= pmic_reg_write(p, MAX8998_REG_LDO17, val);
+
+ /* Disable unneeded regulators */
+ /*
+ * ONOFF1
+ * Buck1 ON, Buck2 OFF, Buck3 ON, Buck4 ON
+ * LDO2 ON, LDO3 OFF, LDO4 OFF, LDO5 ON
+ */
+ val = 0xB9;
+ ret |= pmic_reg_write(p, MAX8998_REG_ONOFF1, val);
+
+ /* ONOFF2
+ * LDO6 OFF, LDO7 ON, LDO8 OFF, LDO9 ON,
+ * LDO10 OFF, LDO11 OFF, LDO12 OFF, LDO13 OFF
+ */
+ val = 0x50;
+ ret |= pmic_reg_write(p, MAX8998_REG_ONOFF2, val);
+
+ /* ONOFF3
+ * LDO14 OFF, LDO15 OFF, LGO16 OFF, LDO17 OFF
+ * EPWRHOLD OFF, EBATTMON OFF, ELBCNFG2 OFF, ELBCNFG1 OFF
+ */
+ val = 0x00;
+ ret |= pmic_reg_write(p, MAX8998_REG_ONOFF3, val);
+
+ if (ret)
+ puts("LCD pmic initialisation error!\n");
+}
+
+static void lcd_cfg_gpio(void)
+{
+ unsigned int i, f3_end = 4;
+
+ for (i = 0; i < 8; i++) {
+ /* set GPF0,1,2[0:7] for RGB Interface and Data lines (32bit) */
+ s5p_gpio_cfg_pin(&gpio1->f0, i, GPIO_FUNC(2));
+ s5p_gpio_cfg_pin(&gpio1->f1, i, GPIO_FUNC(2));
+ s5p_gpio_cfg_pin(&gpio1->f2, i, GPIO_FUNC(2));
+ /* pull-up/down disable */
+ s5p_gpio_set_pull(&gpio1->f0, i, GPIO_PULL_NONE);
+ s5p_gpio_set_pull(&gpio1->f1, i, GPIO_PULL_NONE);
+ s5p_gpio_set_pull(&gpio1->f2, i, GPIO_PULL_NONE);
+
+ /* drive strength to max (24bit) */
+ s5p_gpio_set_drv(&gpio1->f0, i, GPIO_DRV_4X);
+ s5p_gpio_set_rate(&gpio1->f0, i, GPIO_DRV_SLOW);
+ s5p_gpio_set_drv(&gpio1->f1, i, GPIO_DRV_4X);
+ s5p_gpio_set_rate(&gpio1->f1, i, GPIO_DRV_SLOW);
+ s5p_gpio_set_drv(&gpio1->f2, i, GPIO_DRV_4X);
+ s5p_gpio_set_rate(&gpio1->f0, i, GPIO_DRV_SLOW);
+ }
+
+ for (i = 0; i < f3_end; i++) {
+ /* set GPF3[0:3] for RGB Interface and Data lines (32bit) */
+ s5p_gpio_cfg_pin(&gpio1->f3, i, GPIO_FUNC(2));
+ /* pull-up/down disable */
+ s5p_gpio_set_pull(&gpio1->f3, i, GPIO_PULL_NONE);
+ /* drive strength to max (24bit) */
+ s5p_gpio_set_drv(&gpio1->f3, i, GPIO_DRV_4X);
+ s5p_gpio_set_rate(&gpio1->f3, i, GPIO_DRV_SLOW);
+ }
+
+ /* gpio pad configuration for LCD reset. */
+ s5p_gpio_cfg_pin(&gpio2->y4, 5, GPIO_OUTPUT);
+
+ spi_init();
+}
+
+static void reset_lcd(void)
+{
+ s5p_gpio_set_value(&gpio2->y4, 5, 1);
+ udelay(10000);
+ s5p_gpio_set_value(&gpio2->y4, 5, 0);
+ udelay(10000);
+ s5p_gpio_set_value(&gpio2->y4, 5, 1);
+ udelay(100);
+}
+
+static void lcd_power_on(void)
+{
+ struct pmic *p = get_pmic();
+
+ if (pmic_probe(p))
+ return;
+
+ pmic_set_output(p, MAX8998_REG_ONOFF3, MAX8998_LDO17, LDO_ON);
+ pmic_set_output(p, MAX8998_REG_ONOFF2, MAX8998_LDO7, LDO_ON);
+}
+
+vidinfo_t panel_info = {
+ .vl_freq = 60,
+ .vl_col = 480,
+ .vl_row = 800,
+ .vl_width = 480,
+ .vl_height = 800,
+ .vl_clkp = CONFIG_SYS_HIGH,
+ .vl_hsp = CONFIG_SYS_HIGH,
+ .vl_vsp = CONFIG_SYS_HIGH,
+ .vl_dp = CONFIG_SYS_HIGH,
+
+ .vl_bpix = 5, /* Bits per pixel */
+
+ /* LD9040 LCD Panel */
+ .vl_hspw = 2,
+ .vl_hbpd = 16,
+ .vl_hfpd = 16,
+
+ .vl_vspw = 2,
+ .vl_vbpd = 8,
+ .vl_vfpd = 8,
+ .vl_cmd_allow_len = 0xf,
+
+ .win_id = 0,
+ .cfg_gpio = lcd_cfg_gpio,
+ .backlight_on = NULL,
+ .lcd_power_on = lcd_power_on,
+ .reset_lcd = reset_lcd,
+ .dual_lcd_enabled = 0,
+
+ .init_delay = 0,
+ .power_on_delay = 10000,
+ .reset_delay = 10000,
+ .interface_mode = FIMD_RGB_INTERFACE,
+ .mipi_enabled = 0,
+};
+
+void init_panel_info(vidinfo_t *vid)
+{
+ vid->logo_on = 1;
+ vid->resolution = HD_RESOLUTION;
+ vid->rgb_mode = MODE_RGB_P;
+
+#ifdef CONFIG_TIZEN
+ get_tizen_logo_info(vid);
+#endif
+
+ /* for LD9040. */
+ vid->pclk_name = 1; /* MPLL */
+ vid->sclk_div = 1;
+
+ vid->cfg_ldo = ld9040_cfg_ldo;
+ vid->enable_ldo = ld9040_enable_ldo;
+
+ setenv("lcdinfo", "lcd=ld9040");
+}
+
+int board_init(void)
+{
+ gpio1 = (struct exynos4_gpio_part1 *) EXYNOS4_GPIO_PART1_BASE;
+ gpio2 = (struct exynos4_gpio_part2 *) EXYNOS4_GPIO_PART2_BASE;
+
+ gd->bd->bi_arch_number = MACH_TYPE_UNIVERSAL_C210;
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+#if defined(CONFIG_PMIC)
+ pmic_init();
+ init_pmic_lcd();
+#endif
+
+ check_hw_revision();
+ printf("HW Revision:\t0x%x\n", board_rev);
+
+ return 0;
+}
@@ -34,6 +34,7 @@
#define CONFIG_S5P 1 /* which is in a S5P Family */
#define CONFIG_EXYNOS4210 1 /* which is in a EXYNOS4210 */
#define CONFIG_UNIVERSAL 1 /* working with Universal */
+#define CONFIG_TIZEN 1 /* TIZEN lib */
#include <asm/arch/cpu.h> /* get chip and board defs */
@@ -283,4 +284,16 @@
void soft_spi_init(void);
#endif
+/*
+ * LCD Settings
+ */
+#define CONFIG_EXYNOS_FB
+#define CONFIG_LCD
+#define CONFIG_CMD_BMP
+#define CONFIG_BMP_32BPP
+#define CONFIG_LD9040
+#define CONFIG_EXYNOS_MIPI_DSIM
+#define CONFIG_VIDEO_BMP_GZIP
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE ((520 * 120 * 4) + (1 << 12))
+
#endif /* __CONFIG_H */