@@ -1812,6 +1812,7 @@ config SCSI_VIRTIO
This is the virtual HBA driver for virtio. If the kernel will
be used in a virtual machine, say Y or M.
+source "drivers/scsi/csiostor/Kconfig"
endif # SCSI_LOWLEVEL
@@ -90,6 +90,7 @@ obj-$(CONFIG_SCSI_QLA_FC) += qla2xxx/
obj-$(CONFIG_SCSI_QLA_ISCSI) += libiscsi.o qla4xxx/
obj-$(CONFIG_SCSI_LPFC) += lpfc/
obj-$(CONFIG_SCSI_BFA_FC) += bfa/
+obj-$(CONFIG_SCSI_CHELSIO_FCOE) += csiostor/
obj-$(CONFIG_SCSI_PAS16) += pas16.o
obj-$(CONFIG_SCSI_T128) += t128.o
obj-$(CONFIG_SCSI_DMX3191D) += dmx3191d.o
new file mode 100644
@@ -0,0 +1,20 @@
+config SCSI_CHELSIO_FCOE
+ tristate "Chelsio Communications FCoE support"
+ depends on PCI && SCSI
+ select SCSI_FC_ATTRS
+ select FW_LOADER
+ help
+ This driver supports FCoE Offload functionality over
+ Chelsio T4-based 10Gb Converged Network Adapters.
+
+ For general information about Chelsio and our products, visit
+ our website at <http://www.chelsio.com>.
+
+ For customer support, please visit our customer support page at
+ <http://www.chelsio.com/support.html>.
+
+ Please send feedback to <linux-bugs@chelsio.com>.
+
+ To compile this driver as a module choose M here; the module
+ will be called csiostor.
+
new file mode 100644
@@ -0,0 +1,11 @@
+#
+## Chelsio FCoE driver
+#
+##
+
+ccflags-y += -I$(srctree)/drivers/net/ethernet/chelsio/cxgb4
+
+obj-$(CONFIG_SCSI_CHELSIO_FCOE) += csiostor.o
+
+csiostor-objs := csio_attr.o csio_init.o csio_lnode.o csio_scsi.o \
+ csio_hw.o csio_isr.o csio_mb.o csio_rnode.o csio_wr.o
new file mode 100644
@@ -0,0 +1,4385 @@
+/*
+ * This file is part of the Chelsio FCoE driver for Linux.
+ *
+ * Copyright (c) 2008-2012 Chelsio Communications, Inc. All rights reserved.
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the
+ * OpenIB.org BSD license below:
+ *
+ * Redistribution and use in source and binary forms, with or
+ * without modification, are permitted provided that the following
+ * conditions are met:
+ *
+ * - Redistributions of source code must retain the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer.
+ *
+ * - Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials
+ * provided with the distribution.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
+ * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
+ * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+ * SOFTWARE.
+ */
+
+#include <linux/pci.h>
+#include <linux/pci_regs.h>
+#include <linux/firmware.h>
+#include <linux/stddef.h>
+#include <linux/delay.h>
+#include <linux/string.h>
+#include <linux/compiler.h>
+#include <linux/jiffies.h>
+#include <linux/log2.h>
+
+#include "csio_hw.h"
+#include "csio_lnode.h"
+#include "csio_rnode.h"
+
+int csio_force_master;
+int csio_dbg_level = 0xFEFF;
+unsigned int csio_port_mask = 0xf;
+
+/* Default FW event queue entries. */
+static uint32_t csio_evtq_sz = CSIO_EVTQ_SIZE;
+
+/* Default MSI param level */
+int csio_msi = 2;
+
+/* FCoE function instances */
+static int dev_num;
+
+/* FCoE Adapter types & its description */
+static struct csio_adap_desc csio_fcoe_adapters[] = {
+ {"T440-Dbg 10G", "Chelsio T440-Dbg 10G [FCoE]"},
+ {"T420-CR 10G", "Chelsio T420-CR 10G [FCoE]"},
+ {"T422-CR 10G/1G", "Chelsio T422-CR 10G/1G [FCoE]"},
+ {"T440-CR 10G", "Chelsio T440-CR 10G [FCoE]"},
+ {"T420-BCH 10G", "Chelsio T420-BCH 10G [FCoE]"},
+ {"T440-BCH 10G", "Chelsio T440-BCH 10G [FCoE]"},
+ {"T440-CH 10G", "Chelsio T440-CH 10G [FCoE]"},
+ {"T420-SO 10G", "Chelsio T420-SO 10G [FCoE]"},
+ {"T420-CX4 10G", "Chelsio T420-CX4 10G [FCoE]"},
+ {"T420-BT 10G", "Chelsio T420-BT 10G [FCoE]"},
+ {"T404-BT 1G", "Chelsio T404-BT 1G [FCoE]"},
+ {"B420-SR 10G", "Chelsio B420-SR 10G [FCoE]"},
+ {"B404-BT 1G", "Chelsio B404-BT 1G [FCoE]"},
+ {"T480-CR 10G", "Chelsio T480-CR 10G [FCoE]"},
+ {"T440-LP-CR 10G", "Chelsio T440-LP-CR 10G [FCoE]"},
+ {"T4 FPGA", "Chelsio T4 FPGA [FCoE]"}
+};
+
+static void csio_mgmtm_cleanup(struct csio_mgmtm *);
+static void csio_hw_mbm_cleanup(struct csio_hw *);
+
+/* State machine forward declarations */
+static void csio_hws_uninit(struct csio_hw *, enum csio_hw_ev);
+static void csio_hws_configuring(struct csio_hw *, enum csio_hw_ev);
+static void csio_hws_initializing(struct csio_hw *, enum csio_hw_ev);
+static void csio_hws_ready(struct csio_hw *, enum csio_hw_ev);
+static void csio_hws_quiescing(struct csio_hw *, enum csio_hw_ev);
+static void csio_hws_quiesced(struct csio_hw *, enum csio_hw_ev);
+static void csio_hws_resetting(struct csio_hw *, enum csio_hw_ev);
+static void csio_hws_removing(struct csio_hw *, enum csio_hw_ev);
+static void csio_hws_pcierr(struct csio_hw *, enum csio_hw_ev);
+
+static void csio_hw_initialize(struct csio_hw *hw);
+static void csio_evtq_stop(struct csio_hw *hw);
+static void csio_evtq_start(struct csio_hw *hw);
+
+int csio_is_hw_ready(struct csio_hw *hw)
+{
+ return csio_match_state(hw, csio_hws_ready);
+}
+
+int csio_is_hw_removing(struct csio_hw *hw)
+{
+ return csio_match_state(hw, csio_hws_removing);
+}
+
+
+/*
+ * csio_hw_wait_op_done_val - wait until an operation is completed
+ * @hw: the HW module
+ * @reg: the register to check for completion
+ * @mask: a single-bit field within @reg that indicates completion
+ * @polarity: the value of the field when the operation is completed
+ * @attempts: number of check iterations
+ * @delay: delay in usecs between iterations
+ * @valp: where to store the value of the register at completion time
+ *
+ * Wait until an operation is completed by checking a bit in a register
+ * up to @attempts times. If @valp is not NULL the value of the register
+ * at the time it indicated completion is stored there. Returns 0 if the
+ * operation completes and -EAGAIN otherwise.
+ */
+static csio_retval_t
+csio_hw_wait_op_done_val(struct csio_hw *hw, int reg, uint32_t mask,
+ int polarity, int attempts, int delay, uint32_t *valp)
+{
+ uint32_t val;
+ while (1) {
+ val = csio_rd_reg32(hw, reg);
+
+ if (!!(val & mask) == polarity) {
+ if (valp)
+ *valp = val;
+ return CSIO_SUCCESS;
+ }
+
+ if (--attempts == 0)
+ return CSIO_RETRY;
+ if (delay)
+ udelay(delay);
+ }
+}
+
+void
+csio_set_reg_field(struct csio_hw *hw, uint32_t reg, uint32_t mask,
+ uint32_t value)
+{
+ uint32_t val = csio_rd_reg32(hw, reg) & ~mask;
+
+ csio_wr_reg32(hw, val | value, reg);
+ /* Flush */
+ csio_rd_reg32(hw, reg);
+
+}
+
+/*
+ * csio_hw_mc_read - read from MC through backdoor accesses
+ * @hw: the hw module
+ * @addr: address of first byte requested
+ * @data: 64 bytes of data containing the requested address
+ * @ecc: where to store the corresponding 64-bit ECC word
+ *
+ * Read 64 bytes of data from MC starting at a 64-byte-aligned address
+ * that covers the requested address @addr. If @parity is not %NULL it
+ * is assigned the 64-bit ECC word for the read data.
+ */
+csio_retval_t
+csio_hw_mc_read(struct csio_hw *hw, uint32_t addr, uint32_t *data,
+ uint64_t *ecc)
+{
+ int i;
+
+ if (csio_rd_reg32(hw, MC_BIST_CMD) & START_BIST)
+ return CSIO_BUSY;
+ csio_wr_reg32(hw, addr & ~0x3fU, MC_BIST_CMD_ADDR);
+ csio_wr_reg32(hw, 64, MC_BIST_CMD_LEN);
+ csio_wr_reg32(hw, 0xc, MC_BIST_DATA_PATTERN);
+ csio_wr_reg32(hw, BIST_OPCODE(1) | START_BIST | BIST_CMD_GAP(1),
+ MC_BIST_CMD);
+ i = csio_hw_wait_op_done_val(hw, MC_BIST_CMD, START_BIST,
+ 0, 10, 1, NULL);
+ if (i)
+ return i;
+
+#define MC_DATA(i) MC_BIST_STATUS_REG(MC_BIST_STATUS_RDATA, i)
+
+ for (i = 15; i >= 0; i--)
+ *data++ = htonl(csio_rd_reg32(hw, MC_DATA(i)));
+ if (ecc)
+ *ecc = csio_rd_reg64(hw, MC_DATA(16));
+#undef MC_DATA
+ return 0;
+}
+
+/*
+ * csio_hw_edc_read - read from EDC through backdoor accesses
+ * @hw: the hw module
+ * @idx: which EDC to access
+ * @addr: address of first byte requested
+ * @data: 64 bytes of data containing the requested address
+ * @ecc: where to store the corresponding 64-bit ECC word
+ *
+ * Read 64 bytes of data from EDC starting at a 64-byte-aligned address
+ * that covers the requested address @addr. If @parity is not %NULL it
+ * is assigned the 64-bit ECC word for the read data.
+ */
+csio_retval_t
+csio_hw_edc_read(struct csio_hw *hw, int idx, uint32_t addr, uint32_t *data,
+ uint64_t *ecc)
+{
+ int i;
+
+ idx *= EDC_STRIDE;
+ if (csio_rd_reg32(hw, EDC_BIST_CMD + idx) & START_BIST)
+ return CSIO_BUSY;
+ csio_wr_reg32(hw, addr & ~0x3fU, EDC_BIST_CMD_ADDR + idx);
+ csio_wr_reg32(hw, 64, EDC_BIST_CMD_LEN + idx);
+ csio_wr_reg32(hw, 0xc, EDC_BIST_DATA_PATTERN + idx);
+ csio_wr_reg32(hw, BIST_OPCODE(1) | BIST_CMD_GAP(1) | START_BIST,
+ EDC_BIST_CMD + idx);
+ i = csio_hw_wait_op_done_val(hw, EDC_BIST_CMD + idx, START_BIST,
+ 0, 10, 1, NULL);
+ if (i)
+ return i;
+
+#define EDC_DATA(i) (EDC_BIST_STATUS_REG(EDC_BIST_STATUS_RDATA, i) + idx)
+
+ for (i = 15; i >= 0; i--)
+ *data++ = htonl(csio_rd_reg32(hw, EDC_DATA(i)));
+ if (ecc)
+ *ecc = csio_rd_reg64(hw, EDC_DATA(16));
+#undef EDC_DATA
+ return 0;
+}
+
+/*
+ * csio_mem_win_rw - read/write memory through PCIE memory window
+ * @hw: the adapter
+ * @addr: address of first byte requested
+ * @data: MEMWIN0_APERTURE bytes of data containing the requested address
+ * @dir: direction of transfer 1 => read, 0 => write
+ *
+ * Read/write MEMWIN0_APERTURE bytes of data from MC starting at a
+ * MEMWIN0_APERTURE-byte-aligned address that covers the requested
+ * address @addr.
+ */
+static int
+csio_mem_win_rw(struct csio_hw *hw, u32 addr, __be32 *data, int dir)
+{
+ int i;
+
+ /*
+ * Setup offset into PCIE memory window. Address must be a
+ * MEMWIN0_APERTURE-byte-aligned address. (Read back MA register to
+ * ensure that changes propagate before we attempt to use the new
+ * values.)
+ */
+ csio_wr_reg32(hw, addr & ~(MEMWIN0_APERTURE - 1),
+ PCIE_MEM_ACCESS_OFFSET);
+ csio_rd_reg32(hw, PCIE_MEM_ACCESS_OFFSET);
+
+ /* Collecting data 4 bytes at a time upto MEMWIN0_APERTURE */
+ for (i = 0; i < MEMWIN0_APERTURE; i = i + sizeof(__be32)) {
+ if (dir)
+ *data++ = csio_rd_reg32(hw, (MEMWIN0_BASE + i));
+ else
+ csio_wr_reg32(hw, *data++, (MEMWIN0_BASE + i));
+ }
+
+ return 0;
+}
+
+/*
+ * csio_memory_rw - read/write EDC 0, EDC 1 or MC via PCIE memory window
+ * @hw: the csio_hw
+ * @mtype: memory type: MEM_EDC0, MEM_EDC1 or MEM_MC
+ * @addr: address within indicated memory type
+ * @len: amount of memory to transfer
+ * @buf: host memory buffer
+ * @dir: direction of transfer 1 => read, 0 => write
+ *
+ * Reads/writes an [almost] arbitrary memory region in the firmware: the
+ * firmware memory address, length and host buffer must be aligned on
+ * 32-bit boudaries. The memory is transferred as a raw byte sequence
+ * from/to the firmware's memory. If this memory contains data
+ * structures which contain multi-byte integers, it's the callers
+ * responsibility to perform appropriate byte order conversions.
+ */
+static csio_retval_t
+csio_memory_rw(struct csio_hw *hw, int mtype, u32 addr, u32 len,
+ uint32_t *buf, int dir)
+{
+ uint32_t pos, start, end, offset, memoffset;
+ int ret;
+ __be32 *data;
+
+ /*
+ * Argument sanity checks ...
+ */
+ if ((addr & 0x3) || (len & 0x3))
+ return CSIO_INVAL;
+
+ data = kmalloc(MEMWIN0_APERTURE, GFP_KERNEL);
+ if (!data)
+ return CSIO_NOMEM;
+
+ /* Offset into the region of memory which is being accessed
+ * MEM_EDC0 = 0
+ * MEM_EDC1 = 1
+ * MEM_MC = 2
+ */
+ memoffset = (mtype * (5 * 1024 * 1024));
+
+ /* Determine the PCIE_MEM_ACCESS_OFFSET */
+ addr = addr + memoffset;
+
+ /*
+ * The underlaying EDC/MC read routines read MEMWIN0_APERTURE bytes
+ * at a time so we need to round down the start and round up the end.
+ * We'll start copying out of the first line at (addr - start) a word
+ * at a time.
+ */
+ start = addr & ~(MEMWIN0_APERTURE-1);
+ end = (addr + len + MEMWIN0_APERTURE-1) & ~(MEMWIN0_APERTURE-1);
+ offset = (addr - start)/sizeof(__be32);
+
+ for (pos = start; pos < end; pos += MEMWIN0_APERTURE, offset = 0) {
+ /*
+ * If we're writing, copy the data from the caller's memory
+ * buffer
+ */
+ if (!dir) {
+ /*
+ * If we're doing a partial write, then we need to do
+ * a read-modify-write ...
+ */
+ if (offset || len < MEMWIN0_APERTURE) {
+ ret = csio_mem_win_rw(hw, pos, data, 1);
+ if (ret) {
+ kfree(data);
+ return ret;
+ }
+ }
+ while (offset < (MEMWIN0_APERTURE/sizeof(__be32)) &&
+ len > 0) {
+ data[offset++] = *buf++;
+ len -= sizeof(__be32);
+ }
+ }
+
+ /*
+ * Transfer a block of memory and bail if there's an error.
+ */
+ ret = csio_mem_win_rw(hw, pos, data, dir);
+ if (ret) {
+ kfree(data);
+ return ret;
+ }
+
+ /*
+ * If we're reading, copy the data into the caller's memory
+ * buffer.
+ */
+ if (dir)
+ while (offset < (MEMWIN0_APERTURE/sizeof(__be32)) &&
+ len > 0) {
+ *buf++ = data[offset++];
+ len -= sizeof(__be32);
+ }
+ }
+
+ kfree(data);
+
+ return 0;
+}
+
+static csio_retval_t
+csio_memory_write(struct csio_hw *hw, int mtype, u32 addr, u32 len, __be32 *buf)
+{
+ return csio_memory_rw(hw, mtype, addr, len, buf, 0);
+}
+
+/*
+ * EEPROM reads take a few tens of us while writes can take a bit over 5 ms.
+ */
+#define EEPROM_MAX_RD_POLL 40
+#define EEPROM_MAX_WR_POLL 6
+#define EEPROM_STAT_ADDR 0x7bfc
+#define VPD_BASE 0x400
+#define VPD_BASE_OLD 0
+#define VPD_LEN 512
+#define VPD_INFO_FLD_HDR_SIZE 3
+
+/*
+ * csio_hw_seeprom_read - read a serial EEPROM location
+ * @hw: hw to read
+ * @addr: EEPROM virtual address
+ * @data: where to store the read data
+ *
+ * Read a 32-bit word from a location in serial EEPROM using the card's PCI
+ * VPD capability. Note that this function must be called with a virtual
+ * address.
+ */
+static int
+csio_hw_seeprom_read(struct csio_hw *hw, uint32_t addr, uint32_t *data)
+{
+ uint16_t val = 0;
+ int attempts = EEPROM_MAX_RD_POLL;
+ uint32_t base = hw->params.pci.vpd_cap_addr;
+
+ if (addr >= EEPROMVSIZE || (addr & 3))
+ return CSIO_INVAL;
+
+ pci_write_config_word(hw->pdev, base + PCI_VPD_ADDR, (uint16_t)addr);
+
+ do {
+ udelay(10);
+ pci_read_config_word(hw->pdev, base + PCI_VPD_ADDR, &val);
+ } while (!(val & PCI_VPD_ADDR_F) && --attempts);
+
+ if (!(val & PCI_VPD_ADDR_F)) {
+ csio_err(hw, "reading EEPROM address 0x%x failed\n", addr);
+ return CSIO_INVAL;
+ }
+
+ pci_read_config_dword(hw->pdev, base + PCI_VPD_DATA, data);
+ *data = le32_to_cpu(*data);
+ return 0;
+}
+
+/*
+ * Partial EEPROM Vital Product Data structure. Includes only the ID and
+ * VPD-R sections.
+ */
+struct t4_vpd_hdr {
+ u8 id_tag;
+ u8 id_len[2];
+ u8 id_data[ID_LEN];
+ u8 vpdr_tag;
+ u8 vpdr_len[2];
+};
+
+/*
+ * csio_hw_get_vpd_keyword_val - Locates an information field keyword in
+ * the VPD
+ * @v: Pointer to buffered vpd data structure
+ * @kw: The keyword to search for
+ *
+ * Returns the value of the information field keyword or
+ * CSIO_INVAL otherwise.
+ */
+static int
+csio_hw_get_vpd_keyword_val(const struct t4_vpd_hdr *v, const char *kw)
+{
+ int32_t i;
+ int32_t offset , len;
+ const uint8_t *buf = &v->id_tag;
+ const uint8_t *vpdr_len = &v->vpdr_tag;
+ offset = sizeof(struct t4_vpd_hdr);
+ len = (uint16_t)vpdr_len[1] + ((uint16_t)vpdr_len[2] << 8);
+
+ if (len + sizeof(struct t4_vpd_hdr) > VPD_LEN)
+ return CSIO_INVAL;
+
+ for (i = offset; (i + VPD_INFO_FLD_HDR_SIZE) <= (offset + len);) {
+ if (memcmp(buf + i , kw, 2) == 0) {
+ i += VPD_INFO_FLD_HDR_SIZE;
+ return i;
+ }
+
+ i += VPD_INFO_FLD_HDR_SIZE + buf[i+2];
+ }
+
+ return CSIO_INVAL;
+}
+
+static int
+csio_pci_capability(struct pci_dev *pdev, int cap, int *pos)
+{
+ *pos = pci_find_capability(pdev, cap);
+ if (*pos)
+ return 0;
+
+ return -1;
+}
+
+/*
+ * csio_hw_get_vpd_params - read VPD parameters from VPD EEPROM
+ * @hw: HW module
+ * @p: where to store the parameters
+ *
+ * Reads card parameters stored in VPD EEPROM.
+ */
+static csio_retval_t
+csio_hw_get_vpd_params(struct csio_hw *hw, struct csio_vpd *p)
+{
+ int i, ret, ec, sn, addr;
+ uint8_t vpd[VPD_LEN], csum;
+ const struct t4_vpd_hdr *v;
+ /* To get around compilation warning from strstrip */
+ char *s;
+
+ if (csio_is_valid_vpd(hw))
+ return CSIO_SUCCESS;
+
+ ret = csio_pci_capability(hw->pdev, PCI_CAP_ID_VPD,
+ &hw->params.pci.vpd_cap_addr);
+ if (ret)
+ return ret;
+
+ /*
+ * Card information normally starts at VPD_BASE but early cards had
+ * it at 0.
+ */
+ ret = csio_hw_seeprom_read(hw, VPD_BASE, (uint32_t *)(vpd));
+ addr = *vpd == 0x82 ? VPD_BASE : VPD_BASE_OLD;
+
+ for (i = 0; i < sizeof(vpd); i += 4) {
+ ret = csio_hw_seeprom_read(hw, addr + i, (uint32_t *)(vpd + i));
+ if (ret)
+ return ret;
+ }
+
+ /* Reset the VPD flag! */
+ hw->flags &= (~CSIO_HWF_VPD_VALID);
+
+ v = (const struct t4_vpd_hdr *)vpd;
+
+#define FIND_VPD_KW(var, name) do { \
+ var = csio_hw_get_vpd_keyword_val(v, name); \
+ if (var < 0) { \
+ csio_err(hw, "missing VPD keyword " name "\n"); \
+ return CSIO_INVAL; \
+ } \
+} while (0)
+
+ FIND_VPD_KW(i, "RV");
+ for (csum = 0; i >= 0; i--)
+ csum += vpd[i];
+
+ if (csum) {
+ csio_err(hw, "corrupted VPD EEPROM, actual csum %u\n", csum);
+ return CSIO_INVAL;
+ }
+ FIND_VPD_KW(ec, "EC");
+ FIND_VPD_KW(sn, "SN");
+#undef FIND_VPD_KW
+
+ memcpy(p->id, v->id_data, ID_LEN);
+ s = strstrip(p->id);
+ memcpy(p->ec, vpd + ec, EC_LEN);
+ s = strstrip(p->ec);
+ i = vpd[sn - VPD_INFO_FLD_HDR_SIZE + 2];
+ memcpy(p->sn, vpd + sn, min(i, SERNUM_LEN));
+ s = strstrip(p->sn);
+
+ csio_valid_vpd_copied(hw);
+ return 0;
+}
+
+/*
+ * csio_hw_sf1_read - read data from the serial flash
+ * @hw: the HW module
+ * @byte_cnt: number of bytes to read
+ * @cont: whether another operation will be chained
+ * @lock: whether to lock SF for PL access only
+ * @valp: where to store the read data
+ *
+ * Reads up to 4 bytes of data from the serial flash. The location of
+ * the read needs to be specified prior to calling this by issuing the
+ * appropriate commands to the serial flash.
+ */
+static csio_retval_t
+csio_hw_sf1_read(struct csio_hw *hw, uint32_t byte_cnt, int32_t cont,
+ int32_t lock, uint32_t *valp)
+{
+ csio_retval_t ret;
+
+ if (!byte_cnt || byte_cnt > 4)
+ return CSIO_INVAL;
+ if (csio_rd_reg32(hw, SF_OP) & SF_BUSY)
+ return CSIO_BUSY;
+
+ cont = cont ? SF_CONT : 0;
+ lock = lock ? SF_LOCK : 0;
+
+ csio_wr_reg32(hw, lock | cont | BYTECNT(byte_cnt - 1), SF_OP);
+ ret = csio_hw_wait_op_done_val(hw, SF_OP, SF_BUSY, 0, SF_ATTEMPTS,
+ 10, NULL);
+ if (!ret)
+ *valp = csio_rd_reg32(hw, SF_DATA);
+ return ret;
+}
+
+/*
+ * csio_hw_sf1_write - write data to the serial flash
+ * @hw: the HW module
+ * @byte_cnt: number of bytes to write
+ * @cont: whether another operation will be chained
+ * @lock: whether to lock SF for PL access only
+ * @val: value to write
+ *
+ * Writes up to 4 bytes of data to the serial flash. The location of
+ * the write needs to be specified prior to calling this by issuing the
+ * appropriate commands to the serial flash.
+ */
+static csio_retval_t
+csio_hw_sf1_write(struct csio_hw *hw, uint32_t byte_cnt, uint32_t cont,
+ int32_t lock, uint32_t val)
+{
+ if (!byte_cnt || byte_cnt > 4)
+ return CSIO_INVAL;
+ if (csio_rd_reg32(hw, SF_OP) & SF_BUSY)
+ return CSIO_BUSY;
+
+ cont = cont ? SF_CONT : 0;
+ lock = lock ? SF_LOCK : 0;
+
+ csio_wr_reg32(hw, val, SF_DATA);
+ csio_wr_reg32(hw, cont | BYTECNT(byte_cnt - 1) | OP_WR | lock, SF_OP);
+
+ return csio_hw_wait_op_done_val(hw, SF_OP, SF_BUSY, 0, SF_ATTEMPTS,
+ 10, NULL);
+}
+
+/*
+ * csio_hw_flash_wait_op - wait for a flash operation to complete
+ * @hw: the HW module
+ * @attempts: max number of polls of the status register
+ * @delay: delay between polls in ms
+ *
+ * Wait for a flash operation to complete by polling the status register.
+ */
+static csio_retval_t
+csio_hw_flash_wait_op(struct csio_hw *hw, int32_t attempts, int32_t delay)
+{
+ csio_retval_t ret;
+ uint32_t status;
+
+ while (1) {
+ ret = csio_hw_sf1_write(hw, 1, 1, 1, SF_RD_STATUS);
+ if (ret != CSIO_SUCCESS)
+ return ret;
+
+ ret = csio_hw_sf1_read(hw, 1, 0, 1, &status);
+ if (ret != CSIO_SUCCESS)
+ return ret;
+
+ if (!(status & 1))
+ return CSIO_SUCCESS;
+ if (--attempts == 0)
+ return CSIO_RETRY;
+ if (delay)
+ msleep(delay);
+ }
+}
+
+/*
+ * csio_hw_read_flash - read words from serial flash
+ * @hw: the HW module
+ * @addr: the start address for the read
+ * @nwords: how many 32-bit words to read
+ * @data: where to store the read data
+ * @byte_oriented: whether to store data as bytes or as words
+ *
+ * Read the specified number of 32-bit words from the serial flash.
+ * If @byte_oriented is set the read data is stored as a byte array
+ * (i.e., big-endian), otherwise as 32-bit words in the platform's
+ * natural endianess.
+ */
+static csio_retval_t
+csio_hw_read_flash(struct csio_hw *hw, uint32_t addr, uint32_t nwords,
+ uint32_t *data, int32_t byte_oriented)
+{
+ csio_retval_t ret;
+
+ if (addr + nwords * sizeof(uint32_t) > hw->params.sf_size || (addr & 3))
+ return CSIO_INVAL;
+
+ addr = swab32(addr) | SF_RD_DATA_FAST;
+
+ ret = csio_hw_sf1_write(hw, 4, 1, 0, addr);
+ if (ret != CSIO_SUCCESS)
+ return ret;
+
+ ret = csio_hw_sf1_read(hw, 1, 1, 0, data);
+ if (ret != CSIO_SUCCESS)
+ return ret;
+
+ for ( ; nwords; nwords--, data++) {
+ ret = csio_hw_sf1_read(hw, 4, nwords > 1, nwords == 1, data);
+ if (nwords == 1)
+ csio_wr_reg32(hw, 0, SF_OP); /* unlock SF */
+ if (ret)
+ return ret;
+ if (byte_oriented)
+ *data = htonl(*data);
+ }
+ return CSIO_SUCCESS;
+}
+
+/*
+ * csio_hw_write_flash - write up to a page of data to the serial flash
+ * @hw: the hw
+ * @addr: the start address to write
+ * @n: length of data to write in bytes
+ * @data: the data to write
+ *
+ * Writes up to a page of data (256 bytes) to the serial flash starting
+ * at the given address. All the data must be written to the same page.
+ */
+static csio_retval_t
+csio_hw_write_flash(struct csio_hw *hw, uint32_t addr,
+ uint32_t n, const uint8_t *data)
+{
+ csio_retval_t ret = CSIO_INVAL;
+ uint32_t buf[64];
+ uint32_t i, c, left, val, offset = addr & 0xff;
+
+ if (addr >= hw->params.sf_size || offset + n > SF_PAGE_SIZE)
+ return CSIO_INVAL;
+
+ val = swab32(addr) | SF_PROG_PAGE;
+
+ ret = csio_hw_sf1_write(hw, 1, 0, 1, SF_WR_ENABLE);
+ if (ret != CSIO_SUCCESS)
+ goto unlock;
+
+ ret = csio_hw_sf1_write(hw, 4, 1, 1, val);
+ if (ret != CSIO_SUCCESS)
+ goto unlock;
+
+ for (left = n; left; left -= c) {
+ c = min(left, 4U);
+ for (val = 0, i = 0; i < c; ++i)
+ val = (val << 8) + *data++;
+
+ ret = csio_hw_sf1_write(hw, c, c != left, 1, val);
+ if (ret)
+ goto unlock;
+ }
+ ret = csio_hw_flash_wait_op(hw, 8, 1);
+ if (ret)
+ goto unlock;
+
+ csio_wr_reg32(hw, 0, SF_OP); /* unlock SF */
+
+ /* Read the page to verify the write succeeded */
+ ret = csio_hw_read_flash(hw, addr & ~0xff, ARRAY_SIZE(buf), buf, 1);
+ if (ret)
+ return ret;
+
+ if (memcmp(data - n, (uint8_t *)buf + offset, n)) {
+ csio_err(hw,
+ "failed to correctly write the flash page at %#x\n",
+ addr);
+ return CSIO_INVAL;
+ }
+
+ return CSIO_SUCCESS;
+
+unlock:
+ csio_wr_reg32(hw, 0, SF_OP); /* unlock SF */
+ return ret;
+}
+
+/*
+ * csio_hw_flash_erase_sectors - erase a range of flash sectors
+ * @hw: the HW module
+ * @start: the first sector to erase
+ * @end: the last sector to erase
+ *
+ * Erases the sectors in the given inclusive range.
+ */
+static csio_retval_t
+csio_hw_flash_erase_sectors(struct csio_hw *hw, int32_t start, int32_t end)
+{
+ csio_retval_t ret = CSIO_SUCCESS;
+
+ while (start <= end) {
+
+ ret = csio_hw_sf1_write(hw, 1, 0, 1, SF_WR_ENABLE);
+ if (ret != CSIO_SUCCESS)
+ goto out;
+
+ ret = csio_hw_sf1_write(hw, 4, 0, 1,
+ SF_ERASE_SECTOR | (start << 8));
+ if (ret != CSIO_SUCCESS)
+ goto out;
+
+ ret = csio_hw_flash_wait_op(hw, 14, 500);
+ if (ret != CSIO_SUCCESS)
+ goto out;
+
+ start++;
+ }
+out:
+ if (ret)
+ csio_err(hw, "erase of flash sector %d failed, error %d\n",
+ start, ret);
+ csio_wr_reg32(hw, 0, SF_OP); /* unlock SF */
+ return CSIO_SUCCESS;
+}
+
+/*
+ * csio_hw_flash_cfg_addr - return the address of the flash
+ * configuration file
+ * @hw: the HW module
+ *
+ * Return the address within the flash where the Firmware Configuration
+ * File is stored.
+ */
+static unsigned int
+csio_hw_flash_cfg_addr(struct csio_hw *hw)
+{
+ if (hw->params.sf_size == 0x100000)
+ return FPGA_FLASH_CFG_OFFSET;
+ else
+ return FLASH_CFG_OFFSET;
+}
+
+static void
+csio_hw_print_fw_version(struct csio_hw *hw, char *str)
+{
+ csio_info(hw, "%s: %u.%u.%u.%u\n", str,
+ FW_HDR_FW_VER_MAJOR_GET(hw->fwrev),
+ FW_HDR_FW_VER_MINOR_GET(hw->fwrev),
+ FW_HDR_FW_VER_MICRO_GET(hw->fwrev),
+ FW_HDR_FW_VER_BUILD_GET(hw->fwrev));
+}
+
+/*
+ * csio_hw_get_fw_version - read the firmware version
+ * @hw: HW module
+ * @vers: where to place the version
+ *
+ * Reads the FW version from flash.
+ */
+static csio_retval_t
+csio_hw_get_fw_version(struct csio_hw *hw, uint32_t *vers)
+{
+ return csio_hw_read_flash(hw, FW_IMG_START +
+ offsetof(struct fw_hdr, fw_ver), 1,
+ vers, 0);
+}
+
+/*
+ * csio_hw_get_tp_version - read the TP microcode version
+ * @hw: HW module
+ * @vers: where to place the version
+ *
+ * Reads the TP microcode version from flash.
+ */
+static int
+csio_hw_get_tp_version(struct csio_hw *hw, u32 *vers)
+{
+ return csio_hw_read_flash(hw, FLASH_FW_START +
+ offsetof(struct fw_hdr, tp_microcode_ver), 1,
+ vers, 0);
+}
+
+/*
+ * csio_hw_check_fw_version - check if the FW is compatible with
+ * this driver
+ * @hw: HW module
+ *
+ * Checks if an adapter's FW is compatible with the driver. Returns 0
+ * if there's exact match, a negative error if the version could not be
+ * read or there's a major/minor version mismatch/minor.
+ */
+static int
+csio_hw_check_fw_version(struct csio_hw *hw)
+{
+ int ret, major, minor, micro;
+
+ ret = csio_hw_get_fw_version(hw, &hw->fwrev);
+ if (!ret)
+ ret = csio_hw_get_tp_version(hw, &hw->tp_vers);
+ if (ret)
+ return ret;
+
+ major = FW_HDR_FW_VER_MAJOR_GET(hw->fwrev);
+ minor = FW_HDR_FW_VER_MINOR_GET(hw->fwrev);
+ micro = FW_HDR_FW_VER_MICRO_GET(hw->fwrev);
+
+ if (major != FW_VERSION_MAJOR) { /* major mismatch - fail */
+ csio_err(hw, "card FW has major version %u, driver wants %u\n",
+ major, FW_VERSION_MAJOR);
+ return CSIO_INVAL;
+ }
+
+ if (minor == FW_VERSION_MINOR && micro == FW_VERSION_MICRO)
+ return CSIO_SUCCESS; /* perfect match */
+
+ /* Minor/micro version mismatch */
+ return CSIO_INVAL;
+}
+
+/*
+ * csio_hw_fw_dload - download firmware.
+ * @hw: HW module
+ * @fw_data: firmware image to write.
+ * @size: image size
+ *
+ * Write the supplied firmware image to the card's serial flash.
+ */
+static csio_retval_t
+csio_hw_fw_dload(struct csio_hw *hw, uint8_t *fw_data, uint32_t size)
+{
+ uint32_t csum;
+ int32_t addr;
+ csio_retval_t ret;
+ uint32_t i;
+ uint8_t first_page[SF_PAGE_SIZE];
+ const uint32_t *p = (const uint32_t *)fw_data;
+ struct fw_hdr *hdr = (struct fw_hdr *)fw_data;
+ uint32_t sf_sec_size;
+
+ if ((!hw->params.sf_size) || (!hw->params.sf_nsec)) {
+ csio_err(hw, "Serial Flash data invalid\n");
+ return CSIO_INVAL;
+ }
+
+ if (!size) {
+ csio_err(hw, "FW image has no data\n");
+ return CSIO_INVAL;
+ }
+
+ if (size & 511) {
+ csio_err(hw, "FW image size not multiple of 512 bytes\n");
+ return CSIO_INVAL;
+ }
+
+ if (ntohs(hdr->len512) * 512 != size) {
+ csio_err(hw, "FW image size differs from size in FW header\n");
+ return CSIO_INVAL;
+ }
+
+ if (size > FW_MAX_SIZE) {
+ csio_err(hw, "FW image too large, max is %u bytes\n",
+ FW_MAX_SIZE);
+ return CSIO_INVAL;
+ }
+
+ for (csum = 0, i = 0; i < size / sizeof(csum); i++)
+ csum += ntohl(p[i]);
+
+ if (csum != 0xffffffff) {
+ csio_err(hw, "corrupted firmware image, checksum %#x\n", csum);
+ return CSIO_INVAL;
+ }
+
+ sf_sec_size = hw->params.sf_size / hw->params.sf_nsec;
+ i = CSIO_ROUNDUP(size, sf_sec_size); /* # of sectors spanned */
+
+ csio_dbg(hw, "Erasing sectors... start:%d end:%d\n",
+ FW_START_SEC, FW_START_SEC + i - 1);
+
+ ret = csio_hw_flash_erase_sectors(hw, FW_START_SEC,
+ FW_START_SEC + i - 1);
+ if (ret) {
+ csio_err(hw, "Flash Erase failed\n");
+ goto out;
+ }
+
+ /*
+ * We write the correct version at the end so the driver can see a bad
+ * version if the FW write fails. Start by writing a copy of the
+ * first page with a bad version.
+ */
+ memcpy(first_page, fw_data, SF_PAGE_SIZE);
+ ((struct fw_hdr *)first_page)->fw_ver = htonl(0xffffffff);
+ ret = csio_hw_write_flash(hw, FW_IMG_START, SF_PAGE_SIZE, first_page);
+ if (ret)
+ goto out;
+
+ csio_dbg(hw, "Writing Flash .. start:%d end:%d\n",
+ FW_IMG_START, FW_IMG_START + size);
+
+ addr = FW_IMG_START;
+ for (size -= SF_PAGE_SIZE; size; size -= SF_PAGE_SIZE) {
+ addr += SF_PAGE_SIZE;
+ fw_data += SF_PAGE_SIZE;
+ ret = csio_hw_write_flash(hw, addr, SF_PAGE_SIZE, fw_data);
+ if (ret)
+ goto out;
+ }
+
+ ret = csio_hw_write_flash(hw,
+ FW_IMG_START +
+ offsetof(struct fw_hdr, fw_ver),
+ sizeof(hdr->fw_ver),
+ (const uint8_t *)&hdr->fw_ver);
+
+out:
+ if (ret)
+ csio_err(hw, "firmware download failed, error %d\n", ret);
+ return ret;
+}
+
+static csio_retval_t
+csio_hw_get_flash_params(struct csio_hw *hw)
+{
+ csio_retval_t ret;
+ uint32_t info = 0;
+
+ ret = csio_hw_sf1_write(hw, 1, 1, 0, SF_RD_ID);
+ if (!ret)
+ ret = csio_hw_sf1_read(hw, 3, 0, 1, &info);
+ csio_wr_reg32(hw, 0, SF_OP); /* unlock SF */
+ if (ret != CSIO_SUCCESS)
+ return ret;
+
+ if ((info & 0xff) != 0x20) /* not a Numonix flash */
+ return CSIO_INVAL;
+ info >>= 16; /* log2 of size */
+ if (info >= 0x14 && info < 0x18)
+ hw->params.sf_nsec = 1 << (info - 16);
+ else if (info == 0x18)
+ hw->params.sf_nsec = 64;
+ else
+ return CSIO_INVAL;
+ hw->params.sf_size = 1 << info;
+
+ return CSIO_SUCCESS;
+}
+
+static void
+csio_set_pcie_completion_timeout(struct csio_hw *hw, u8 range)
+{
+ uint16_t val;
+ uint32_t pcie_cap;
+
+ if (!csio_pci_capability(hw->pdev, PCI_CAP_ID_EXP, &pcie_cap)) {
+ pci_read_config_word(hw->pdev,
+ pcie_cap + PCI_EXP_DEVCTL2, &val);
+ val &= 0xfff0;
+ val |= range ;
+ pci_write_config_word(hw->pdev,
+ pcie_cap + PCI_EXP_DEVCTL2, val);
+ }
+}
+
+
+/*
+ * Return the specified PCI-E Configuration Space register from our Physical
+ * Function. We try first via a Firmware LDST Command since we prefer to let
+ * the firmware own all of these registers, but if that fails we go for it
+ * directly ourselves.
+ */
+static uint32_t
+csio_read_pcie_cfg4(struct csio_hw *hw, int reg)
+{
+ u32 val = 0;
+ struct csio_mb *mbp;
+ int rv;
+ struct fw_ldst_cmd *ldst_cmd;
+
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp) {
+ csio_inc_stats(hw, n_err_nomem);
+ pci_read_config_dword(hw->pdev, reg, &val);
+ return val;
+ }
+
+ csio_mb_ldst(hw, mbp, CSIO_MB_DEFAULT_TMO, reg);
+
+ rv = csio_mb_issue(hw, mbp);
+
+ /*
+ * If the LDST Command suucceeded, exctract the returned register
+ * value. Otherwise read it directly ourself.
+ */
+ if (rv == 0) {
+ ldst_cmd = (struct fw_ldst_cmd *)(mbp->mb);
+ val = ntohl(ldst_cmd->u.pcie.data[0]);
+ } else
+ pci_read_config_dword(hw->pdev, reg, &val);
+
+ mempool_free(mbp, hw->mb_mempool);
+
+ return val;
+} /* csio_read_pcie_cfg4 */
+
+static int
+csio_hw_set_mem_win(struct csio_hw *hw)
+{
+ u32 bar0;
+
+ /*
+ * Truncation intentional: we only read the bottom 32-bits of the
+ * 64-bit BAR0/BAR1 ... We use the hardware backdoor mechanism to
+ * read BAR0 instead of using pci_resource_start() because we could be
+ * operating from within a Virtual Machine which is trapping our
+ * accesses to our Configuration Space and we need to set up the PCI-E
+ * Memory Window decoders with the actual addresses which will be
+ * coming across the PCI-E link.
+ */
+ bar0 = csio_read_pcie_cfg4(hw, PCI_BASE_ADDRESS_0);
+ bar0 &= PCI_BASE_ADDRESS_MEM_MASK;
+
+ /*
+ * Set up memory window for accessing adapter memory ranges. (Read
+ * back MA register to ensure that changes propagate before we attempt
+ * to use the new values.)
+ */
+ csio_wr_reg32(hw, (bar0 + MEMWIN0_BASE) | BIR(0) |
+ WINDOW(ilog2(MEMWIN0_APERTURE) - 10),
+ PCIE_MEM_ACCESS_REG(PCIE_MEM_ACCESS_BASE_WIN, 0));
+ csio_wr_reg32(hw, (bar0 + MEMWIN1_BASE) | BIR(0) |
+ WINDOW(ilog2(MEMWIN1_APERTURE) - 10),
+ PCIE_MEM_ACCESS_REG(PCIE_MEM_ACCESS_BASE_WIN, 1));
+ csio_wr_reg32(hw, (bar0 + MEMWIN2_BASE) | BIR(0) |
+ WINDOW(ilog2(MEMWIN2_APERTURE) - 10),
+ PCIE_MEM_ACCESS_REG(PCIE_MEM_ACCESS_BASE_WIN, 2));
+ csio_rd_reg32(hw, PCIE_MEM_ACCESS_REG(PCIE_MEM_ACCESS_BASE_WIN, 2));
+ return 0;
+} /* csio_hw_set_mem_win */
+
+
+
+/*****************************************************************************/
+/* HW State machine assists */
+/*****************************************************************************/
+
+static csio_retval_t
+csio_hw_dev_ready(struct csio_hw *hw)
+{
+ uint32_t reg;
+ int cnt = 6;
+
+ while (((reg = csio_rd_reg32(hw, PL_WHOAMI)) == 0xFFFFFFFF) &&
+ (--cnt != 0))
+ mdelay(100);
+
+ if ((cnt == 0) && (((int32_t)(SOURCEPF_GET(reg)) < 0) ||
+ (SOURCEPF_GET(reg) >= CSIO_MAX_PFN))) {
+ csio_err(hw, "PL_WHOAMI returned 0x%x, cnt:%d\n", reg, cnt);
+ return CSIO_EIO;
+ }
+
+ hw->pfn = SOURCEPF_GET(reg);
+
+ return CSIO_SUCCESS;
+}
+
+/*
+ * csio_do_hello - Perform the HELLO FW Mailbox command and process response.
+ * @hw: HW module
+ * @state: Device state
+ *
+ * FW_HELLO_CMD has to be polled for completion.
+ */
+static csio_retval_t
+csio_do_hello(struct csio_hw *hw, enum csio_dev_state *state)
+{
+ struct csio_mb *mbp;
+ csio_retval_t rv = CSIO_SUCCESS;
+ enum csio_dev_master master;
+ enum fw_retval retval;
+ uint8_t mpfn;
+ char state_str[16];
+ int retries = FW_CMD_HELLO_RETRIES;
+
+ memset(state_str, 0, sizeof(state_str));
+
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp) {
+ rv = CSIO_NOMEM;
+ csio_inc_stats(hw, n_err_nomem);
+ goto out;
+ }
+
+ master = csio_force_master ? CSIO_MASTER_MUST : CSIO_MASTER_MAY;
+
+retry:
+ csio_mb_hello(hw, mbp, CSIO_MB_DEFAULT_TMO, hw->pfn,
+ hw->pfn, master, NULL);
+
+ rv = csio_mb_issue(hw, mbp);
+ if (rv) {
+ csio_err(hw, "failed to issue HELLO cmd. ret:%d.\n", rv);
+ goto out_free_mb;
+ }
+
+ csio_mb_process_hello_rsp(hw, mbp, &retval, state, &mpfn);
+ if (retval != FW_SUCCESS) {
+ csio_err(hw, "HELLO cmd failed with ret: %d\n", retval);
+ rv = CSIO_INVAL;
+ goto out_free_mb;
+ }
+
+ /* Firmware has designated us to be master */
+ if (hw->pfn == mpfn) {
+ hw->flags |= CSIO_HWF_MASTER;
+ } else if (*state == CSIO_DEV_STATE_UNINIT) {
+ /*
+ * If we're not the Master PF then we need to wait around for
+ * the Master PF Driver to finish setting up the adapter.
+ *
+ * Note that we also do this wait if we're a non-Master-capable
+ * PF and there is no current Master PF; a Master PF may show up
+ * momentarily and we wouldn't want to fail pointlessly. (This
+ * can happen when an OS loads lots of different drivers rapidly
+ * at the same time). In this case, the Master PF returned by
+ * the firmware will be PCIE_FW_MASTER_MASK so the test below
+ * will work ...
+ */
+
+ int waiting = FW_CMD_HELLO_TIMEOUT;
+
+ /*
+ * Wait for the firmware to either indicate an error or
+ * initialized state. If we see either of these we bail out
+ * and report the issue to the caller. If we exhaust the
+ * "hello timeout" and we haven't exhausted our retries, try
+ * again. Otherwise bail with a timeout error.
+ */
+ for (;;) {
+ uint32_t pcie_fw;
+
+ msleep(50);
+ waiting -= 50;
+
+ /*
+ * If neither Error nor Initialialized are indicated
+ * by the firmware keep waiting till we exaust our
+ * timeout ... and then retry if we haven't exhausted
+ * our retries ...
+ */
+ pcie_fw = csio_rd_reg32(hw, PCIE_FW);
+ if (!(pcie_fw & (PCIE_FW_ERR|PCIE_FW_INIT))) {
+ if (waiting <= 0) {
+ if (retries-- > 0)
+ goto retry;
+
+ rv = CSIO_TIMEOUT;
+ break;
+ }
+ continue;
+ }
+
+ /*
+ * We either have an Error or Initialized condition
+ * report errors preferentially.
+ */
+ if (state) {
+ if (pcie_fw & PCIE_FW_ERR) {
+ *state = CSIO_DEV_STATE_ERR;
+ rv = CSIO_TIMEOUT;
+ } else if (pcie_fw & PCIE_FW_INIT)
+ *state = CSIO_DEV_STATE_INIT;
+ }
+
+ /*
+ * If we arrived before a Master PF was selected and
+ * there's not a valid Master PF, grab its identity
+ * for our caller.
+ */
+ if (mpfn == PCIE_FW_MASTER_MASK &&
+ (pcie_fw & PCIE_FW_MASTER_VLD))
+ mpfn = PCIE_FW_MASTER_GET(pcie_fw);
+ break;
+ }
+ hw->flags &= ~CSIO_HWF_MASTER;
+ }
+
+ switch (*state) {
+ case CSIO_DEV_STATE_UNINIT:
+ strcpy(state_str, "Initializing");
+ break;
+ case CSIO_DEV_STATE_INIT:
+ strcpy(state_str, "Initialized");
+ break;
+ case CSIO_DEV_STATE_ERR:
+ strcpy(state_str, "Error");
+ break;
+ default:
+ strcpy(state_str, "Unknown");
+ break;
+ }
+
+ if (hw->pfn == mpfn)
+ csio_info(hw, "PF: %d, Coming up as MASTER, HW state: %s\n",
+ hw->pfn, state_str);
+ else
+ csio_info(hw,
+ "PF: %d, Coming up as SLAVE, Master PF: %d, HW state: %s\n",
+ hw->pfn, mpfn, state_str);
+
+out_free_mb:
+ mempool_free(mbp, hw->mb_mempool);
+out:
+ return rv;
+}
+
+/*
+ * csio_do_bye - Perform the BYE FW Mailbox command and process response.
+ * @hw: HW module
+ *
+ */
+static csio_retval_t
+csio_do_bye(struct csio_hw *hw)
+{
+ struct csio_mb *mbp;
+ enum fw_retval retval;
+
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp) {
+ csio_inc_stats(hw, n_err_nomem);
+ return CSIO_NOMEM;
+ }
+
+ csio_mb_bye(hw, mbp, CSIO_MB_DEFAULT_TMO, NULL);
+
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "Issue of BYE command failed\n");
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ retval = csio_mb_fw_retval(mbp);
+ if (retval != FW_SUCCESS) {
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ mempool_free(mbp, hw->mb_mempool);
+
+ return CSIO_SUCCESS;
+}
+
+/*
+ * csio_do_reset- Perform the device reset.
+ * @hw: HW module
+ * @fw_rst: FW reset
+ *
+ * If fw_rst is set, issues FW reset mbox cmd otherwise
+ * does PIO reset.
+ * Performs reset of the function.
+ */
+static csio_retval_t
+csio_do_reset(struct csio_hw *hw, bool fw_rst)
+{
+ struct csio_mb *mbp;
+ enum fw_retval retval;
+
+ if (!fw_rst) {
+ /* PIO reset */
+ csio_wr_reg32(hw, PIORSTMODE | PIORST, PL_RST);
+ mdelay(2000);
+ return CSIO_SUCCESS;
+ }
+
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp) {
+ csio_inc_stats(hw, n_err_nomem);
+ return CSIO_NOMEM;
+ }
+
+ csio_mb_reset(hw, mbp, CSIO_MB_DEFAULT_TMO,
+ PIORSTMODE | PIORST, 0, NULL);
+
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "Issue of RESET command failed.n");
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ retval = csio_mb_fw_retval(mbp);
+ if (retval != FW_SUCCESS) {
+ csio_err(hw, "RESET cmd failed with ret:0x%x.\n", retval);
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ mempool_free(mbp, hw->mb_mempool);
+
+ return CSIO_SUCCESS;
+}
+
+static csio_retval_t
+csio_hw_validate_caps(struct csio_hw *hw, struct csio_mb *mbp)
+{
+ struct fw_caps_config_cmd *rsp = (struct fw_caps_config_cmd *)mbp->mb;
+ uint16_t caps;
+
+ caps = ntohs(rsp->fcoecaps);
+
+ if (!(caps & FW_CAPS_CONFIG_FCOE_INITIATOR)) {
+ csio_err(hw, "No FCoE Initiator capability in the firmware.\n");
+ return CSIO_INVAL;
+ }
+
+ if (!(caps & FW_CAPS_CONFIG_FCOE_CTRL_OFLD)) {
+ csio_err(hw, "No FCoE Control Offload capability\n");
+ return CSIO_INVAL;
+ }
+
+ return CSIO_SUCCESS;
+}
+
+/*
+ * csio_hw_fw_halt - issue a reset/halt to FW and put uP into RESET
+ * @hw: the HW module
+ * @mbox: mailbox to use for the FW RESET command (if desired)
+ * @force: force uP into RESET even if FW RESET command fails
+ *
+ * Issues a RESET command to firmware (if desired) with a HALT indication
+ * and then puts the microprocessor into RESET state. The RESET command
+ * will only be issued if a legitimate mailbox is provided (mbox <=
+ * PCIE_FW_MASTER_MASK).
+ *
+ * This is generally used in order for the host to safely manipulate the
+ * adapter without fear of conflicting with whatever the firmware might
+ * be doing. The only way out of this state is to RESTART the firmware
+ * ...
+ */
+static csio_retval_t
+csio_hw_fw_halt(struct csio_hw *hw, uint32_t mbox, int32_t force)
+{
+ enum fw_retval retval = 0;
+
+ /*
+ * If a legitimate mailbox is provided, issue a RESET command
+ * with a HALT indication.
+ */
+ if (mbox <= PCIE_FW_MASTER_MASK) {
+ struct csio_mb *mbp;
+
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp) {
+ csio_inc_stats(hw, n_err_nomem);
+ return CSIO_NOMEM;
+ }
+
+ csio_mb_reset(hw, mbp, CSIO_MB_DEFAULT_TMO,
+ PIORSTMODE | PIORST, FW_RESET_CMD_HALT,
+ NULL);
+
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "Issue of RESET command failed!\n");
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ retval = csio_mb_fw_retval(mbp);
+ mempool_free(mbp, hw->mb_mempool);
+ }
+
+ /*
+ * Normally we won't complete the operation if the firmware RESET
+ * command fails but if our caller insists we'll go ahead and put the
+ * uP into RESET. This can be useful if the firmware is hung or even
+ * missing ... We'll have to take the risk of putting the uP into
+ * RESET without the cooperation of firmware in that case.
+ *
+ * We also force the firmware's HALT flag to be on in case we bypassed
+ * the firmware RESET command above or we're dealing with old firmware
+ * which doesn't have the HALT capability. This will serve as a flag
+ * for the incoming firmware to know that it's coming out of a HALT
+ * rather than a RESET ... if it's new enough to understand that ...
+ */
+ if (retval == 0 || force) {
+ csio_set_reg_field(hw, CIM_BOOT_CFG, UPCRST, UPCRST);
+ csio_set_reg_field(hw, PCIE_FW, PCIE_FW_HALT, PCIE_FW_HALT);
+ }
+
+ /*
+ * And we always return the result of the firmware RESET command
+ * even when we force the uP into RESET ...
+ */
+ return retval ? CSIO_INVAL : CSIO_SUCCESS;
+}
+
+/*
+ * csio_hw_fw_restart - restart the firmware by taking the uP out of RESET
+ * @hw: the HW module
+ * @reset: if we want to do a RESET to restart things
+ *
+ * Restart firmware previously halted by csio_hw_fw_halt(). On successful
+ * return the previous PF Master remains as the new PF Master and there
+ * is no need to issue a new HELLO command, etc.
+ *
+ * We do this in two ways:
+ *
+ * 1. If we're dealing with newer firmware we'll simply want to take
+ * the chip's microprocessor out of RESET. This will cause the
+ * firmware to start up from its start vector. And then we'll loop
+ * until the firmware indicates it's started again (PCIE_FW.HALT
+ * reset to 0) or we timeout.
+ *
+ * 2. If we're dealing with older firmware then we'll need to RESET
+ * the chip since older firmware won't recognize the PCIE_FW.HALT
+ * flag and automatically RESET itself on startup.
+ */
+static csio_retval_t
+csio_hw_fw_restart(struct csio_hw *hw, uint32_t mbox, int32_t reset)
+{
+ if (reset) {
+ /*
+ * Since we're directing the RESET instead of the firmware
+ * doing it automatically, we need to clear the PCIE_FW.HALT
+ * bit.
+ */
+ csio_set_reg_field(hw, PCIE_FW, PCIE_FW_HALT, 0);
+
+ /*
+ * If we've been given a valid mailbox, first try to get the
+ * firmware to do the RESET. If that works, great and we can
+ * return success. Otherwise, if we haven't been given a
+ * valid mailbox or the RESET command failed, fall back to
+ * hitting the chip with a hammer.
+ */
+ if (mbox <= PCIE_FW_MASTER_MASK) {
+ csio_set_reg_field(hw, CIM_BOOT_CFG, UPCRST, 0);
+ msleep(100);
+ if (csio_do_reset(hw, CSIO_TRUE) == 0)
+ return CSIO_SUCCESS;
+ }
+
+ csio_wr_reg32(hw, PIORSTMODE | PIORST, PL_RST);
+ msleep(2000);
+ } else {
+ int ms;
+
+ csio_set_reg_field(hw, CIM_BOOT_CFG, UPCRST, 0);
+ for (ms = 0; ms < FW_CMD_MAX_TIMEOUT; ) {
+ if (!(csio_rd_reg32(hw, PCIE_FW) & PCIE_FW_HALT))
+ return CSIO_SUCCESS;
+ msleep(100);
+ ms += 100;
+ }
+ return CSIO_TIMEOUT;
+ }
+ return CSIO_SUCCESS;
+}
+
+/*
+ * csio_hw_fw_upgrade - perform all of the steps necessary to upgrade FW
+ * @hw: the HW module
+ * @mbox: mailbox to use for the FW RESET command (if desired)
+ * @fw_data: the firmware image to write
+ * @size: image size
+ * @force: force upgrade even if firmware doesn't cooperate
+ *
+ * Perform all of the steps necessary for upgrading an adapter's
+ * firmware image. Normally this requires the cooperation of the
+ * existing firmware in order to halt all existing activities
+ * but if an invalid mailbox token is passed in we skip that step
+ * (though we'll still put the adapter microprocessor into RESET in
+ * that case).
+ *
+ * On successful return the new firmware will have been loaded and
+ * the adapter will have been fully RESET losing all previous setup
+ * state. On unsuccessful return the adapter may be completely hosed ...
+ * positive errno indicates that the adapter is ~probably~ intact, a
+ * negative errno indicates that things are looking bad ...
+ */
+static csio_retval_t
+csio_hw_fw_upgrade(struct csio_hw *hw, uint32_t mbox,
+ const u8 *fw_data, uint32_t size, int32_t force)
+{
+ const struct fw_hdr *fw_hdr = (const struct fw_hdr *)fw_data;
+ csio_retval_t reset, ret;
+
+ ret = csio_hw_fw_halt(hw, mbox, force);
+ if (ret != CSIO_SUCCESS && !force)
+ return ret;
+
+ ret = csio_hw_fw_dload(hw, (uint8_t *) fw_data, size);
+ if (ret != CSIO_SUCCESS)
+ return ret;
+
+ /*
+ * Older versions of the firmware don't understand the new
+ * PCIE_FW.HALT flag and so won't know to perform a RESET when they
+ * restart. So for newly loaded older firmware we'll have to do the
+ * RESET for it so it starts up on a clean slate. We can tell if
+ * the newly loaded firmware will handle this right by checking
+ * its header flags to see if it advertises the capability.
+ */
+ reset = ((ntohl(fw_hdr->flags) & FW_HDR_FLAGS_RESET_HALT) == 0);
+ return csio_hw_fw_restart(hw, mbox, reset);
+}
+
+
+/*
+ * csio_hw_fw_config_file - setup an adapter via a Configuration File
+ * @hw: the HW module
+ * @mbox: mailbox to use for the FW command
+ * @mtype: the memory type where the Configuration File is located
+ * @maddr: the memory address where the Configuration File is located
+ * @finiver: return value for CF [fini] version
+ * @finicsum: return value for CF [fini] checksum
+ * @cfcsum: return value for CF computed checksum
+ *
+ * Issue a command to get the firmware to process the Configuration
+ * File located at the specified mtype/maddress. If the Configuration
+ * File is processed successfully and return value pointers are
+ * provided, the Configuration File "[fini] section version and
+ * checksum values will be returned along with the computed checksum.
+ * It's up to the caller to decide how it wants to respond to the
+ * checksums not matching but it recommended that a prominant warning
+ * be emitted in order to help people rapidly identify changed or
+ * corrupted Configuration Files.
+ *
+ * Also note that it's possible to modify things like "niccaps",
+ * "toecaps",etc. between processing the Configuration File and telling
+ * the firmware to use the new configuration. Callers which want to
+ * do this will need to "hand-roll" their own CAPS_CONFIGS commands for
+ * Configuration Files if they want to do this.
+ */
+static csio_retval_t
+csio_hw_fw_config_file(struct csio_hw *hw,
+ unsigned int mtype, unsigned int maddr,
+ uint32_t *finiver, uint32_t *finicsum, uint32_t *cfcsum)
+{
+ struct csio_mb *mbp;
+ struct fw_caps_config_cmd *caps_cmd;
+ csio_retval_t rv = CSIO_INVAL;
+ enum fw_retval ret;
+
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp) {
+ csio_inc_stats(hw, n_err_nomem);
+ return CSIO_NOMEM;
+ }
+ /*
+ * Tell the firmware to process the indicated Configuration File.
+ * If there are no errors and the caller has provided return value
+ * pointers for the [fini] section version, checksum and computed
+ * checksum, pass those back to the caller.
+ */
+ caps_cmd = (struct fw_caps_config_cmd *)(mbp->mb);
+ CSIO_INIT_MBP(mbp, caps_cmd, CSIO_MB_DEFAULT_TMO, hw, NULL, 1);
+ caps_cmd->op_to_write =
+ htonl(FW_CMD_OP(FW_CAPS_CONFIG_CMD) |
+ FW_CMD_REQUEST |
+ FW_CMD_READ);
+ caps_cmd->cfvalid_to_len16 =
+ htonl(FW_CAPS_CONFIG_CMD_CFVALID |
+ FW_CAPS_CONFIG_CMD_MEMTYPE_CF(mtype) |
+ FW_CAPS_CONFIG_CMD_MEMADDR64K_CF(maddr >> 16) |
+ FW_LEN16(*caps_cmd));
+
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "Issue of FW_CAPS_CONFIG_CMD failed!\n");
+ goto out;
+ }
+
+ ret = csio_mb_fw_retval(mbp);
+ if (ret != FW_SUCCESS) {
+ csio_dbg(hw, "FW_CAPS_CONFIG_CMD returned %d!\n", rv);
+ goto out;
+ }
+
+ if (finiver)
+ *finiver = ntohl(caps_cmd->finiver);
+ if (finicsum)
+ *finicsum = ntohl(caps_cmd->finicsum);
+ if (cfcsum)
+ *cfcsum = ntohl(caps_cmd->cfcsum);
+
+ /* Validate device capabilities */
+ if (csio_hw_validate_caps(hw, mbp)) {
+ rv = CSIO_NOSUPP;
+ goto out;
+ }
+
+ /*
+ * And now tell the firmware to use the configuration we just loaded.
+ */
+ caps_cmd->op_to_write =
+ htonl(FW_CMD_OP(FW_CAPS_CONFIG_CMD) |
+ FW_CMD_REQUEST |
+ FW_CMD_WRITE);
+ caps_cmd->cfvalid_to_len16 = htonl(FW_LEN16(*caps_cmd));
+
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "Issue of FW_CAPS_CONFIG_CMD failed!\n");
+ goto out;
+ }
+
+ ret = csio_mb_fw_retval(mbp);
+ if (ret != FW_SUCCESS) {
+ csio_dbg(hw, "FW_CAPS_CONFIG_CMD returned %d!\n", rv);
+ goto out;
+ }
+
+ rv = CSIO_SUCCESS;
+out:
+ mempool_free(mbp, hw->mb_mempool);
+ return rv;
+}
+
+/*
+ * csio_get_device_params - Get device parameters.
+ * @hw: HW module
+ *
+ */
+static csio_retval_t
+csio_get_device_params(struct csio_hw *hw)
+{
+ struct csio_wrm *wrm = csio_hw_to_wrm(hw);
+ struct csio_mb *mbp;
+ enum fw_retval retval;
+ u32 param[6];
+ int i, j = 0;
+
+ /* Initialize portids to -1 */
+ for (i = 0; i < CSIO_MAX_PPORTS; i++)
+ hw->pport[i].portid = -1;
+
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp) {
+ csio_inc_stats(hw, n_err_nomem);
+ return CSIO_NOMEM;
+ }
+
+ /* Get port vec information. */
+ param[0] = FW_PARAM_DEV(PORTVEC);
+
+ /* Get Core clock. */
+ param[1] = FW_PARAM_DEV(CCLK);
+
+ /* Get EQ id start and end. */
+ param[2] = FW_PARAM_PFVF(EQ_START);
+ param[3] = FW_PARAM_PFVF(EQ_END);
+
+ /* Get IQ id start and end. */
+ param[4] = FW_PARAM_PFVF(IQFLINT_START);
+ param[5] = FW_PARAM_PFVF(IQFLINT_END);
+
+ csio_mb_params(hw, mbp, CSIO_MB_DEFAULT_TMO, hw->pfn, 0,
+ ARRAY_SIZE(param), param, NULL, CSIO_FALSE, NULL);
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "Issue of FW_PARAMS_CMD(read) failed!\n");
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ csio_mb_process_read_params_rsp(hw, mbp, &retval,
+ ARRAY_SIZE(param), param);
+ if (retval != FW_SUCCESS) {
+ csio_err(hw, "FW_PARAMS_CMD(read) failed with ret:0x%x!\n",
+ retval);
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ /* cache the information. */
+ hw->port_vec = param[0];
+ hw->vpd.cclk = param[1];
+ wrm->fw_eq_start = param[2];
+ wrm->fw_iq_start = param[4];
+
+ /* Using FW configured max iqs & eqs */
+ if ((hw->flags & CSIO_HWF_USING_SOFT_PARAMS) ||
+ !csio_is_hw_master(hw)) {
+ hw->cfg_niq = param[5] - param[4] + 1;
+ hw->cfg_neq = param[3] - param[2] + 1;
+ csio_dbg(hw, "Using fwconfig max niqs %d neqs %d\n",
+ hw->cfg_niq, hw->cfg_neq);
+ }
+
+ hw->port_vec &= csio_port_mask;
+
+ hw->num_pports = hweight32(hw->port_vec);
+
+ csio_dbg(hw, "Port vector: 0x%x, #ports: %d\n",
+ hw->port_vec, hw->num_pports);
+
+ for (i = 0; i < hw->num_pports; i++) {
+ while ((hw->port_vec & (1 << j)) == 0)
+ j++;
+ hw->pport[i].portid = j++;
+ csio_dbg(hw, "Found Port:%d\n", hw->pport[i].portid);
+ }
+ mempool_free(mbp, hw->mb_mempool);
+
+ return CSIO_SUCCESS;
+}
+
+
+/*
+ * csio_config_device_caps - Get and set device capabilities.
+ * @hw: HW module
+ *
+ */
+static csio_retval_t
+csio_config_device_caps(struct csio_hw *hw)
+{
+ struct csio_mb *mbp;
+ enum fw_retval retval;
+ csio_retval_t rv = CSIO_INVAL;
+
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp) {
+ csio_inc_stats(hw, n_err_nomem);
+ return CSIO_NOMEM;
+ }
+
+ /* Get device capabilities */
+ csio_mb_caps_config(hw, mbp, CSIO_MB_DEFAULT_TMO, 0, 0, 0, 0, NULL);
+
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "Issue of FW_CAPS_CONFIG_CMD(r) failed!\n");
+ goto out;
+ }
+
+ retval = csio_mb_fw_retval(mbp);
+ if (retval != FW_SUCCESS) {
+ csio_err(hw, "FW_CAPS_CONFIG_CMD(r) returned %d!\n", retval);
+ goto out;
+ }
+
+ /* Validate device capabilities */
+ if (csio_hw_validate_caps(hw, mbp))
+ goto out;
+
+ /* Don't config device capabilities if already configured */
+ if (hw->fw_state == CSIO_DEV_STATE_INIT) {
+ rv = CSIO_SUCCESS;
+ goto out;
+ }
+
+ /* Write back desired device capabilities */
+ csio_mb_caps_config(hw, mbp, CSIO_MB_DEFAULT_TMO, CSIO_TRUE, CSIO_TRUE,
+ CSIO_FALSE, CSIO_TRUE, NULL);
+
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "Issue of FW_CAPS_CONFIG_CMD(w) failed!\n");
+ goto out;
+ }
+
+ retval = csio_mb_fw_retval(mbp);
+ if (retval != FW_SUCCESS) {
+ csio_err(hw, "FW_CAPS_CONFIG_CMD(w) returned %d!\n", retval);
+ goto out;
+ }
+
+ rv = CSIO_SUCCESS;
+out:
+ mempool_free(mbp, hw->mb_mempool);
+ return rv;
+}
+
+static csio_retval_t
+csio_config_global_rss(struct csio_hw *hw)
+{
+ struct csio_mb *mbp;
+ enum fw_retval retval;
+
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp) {
+ csio_inc_stats(hw, n_err_nomem);
+ return CSIO_NOMEM;
+ }
+
+ csio_rss_glb_config(hw, mbp, CSIO_MB_DEFAULT_TMO,
+ FW_RSS_GLB_CONFIG_CMD_MODE_BASICVIRTUAL,
+ FW_RSS_GLB_CONFIG_CMD_TNLMAPEN |
+ FW_RSS_GLB_CONFIG_CMD_HASHTOEPLITZ |
+ FW_RSS_GLB_CONFIG_CMD_TNLALLLKP,
+ NULL);
+
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "Issue of FW_RSS_GLB_CONFIG_CMD failed!\n");
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ retval = csio_mb_fw_retval(mbp);
+ if (retval != FW_SUCCESS) {
+ csio_err(hw, "FW_RSS_GLB_CONFIG_CMD returned 0x%x!\n", retval);
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ mempool_free(mbp, hw->mb_mempool);
+
+ return CSIO_SUCCESS;
+}
+
+/*
+ * csio_config_pfvf - Configure Physical/Virtual functions settings.
+ * @hw: HW module
+ *
+ */
+static csio_retval_t
+csio_config_pfvf(struct csio_hw *hw)
+{
+ struct csio_mb *mbp;
+ enum fw_retval retval;
+
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp) {
+ csio_inc_stats(hw, n_err_nomem);
+ return CSIO_NOMEM;
+ }
+
+ /*
+ * For now, allow all PFs to access to all ports using a pmask
+ * value of 0xF (M_FW_PFVF_CMD_PMASK). Once we have VFs, we will
+ * need to provide access based on some rule.
+ */
+ csio_mb_pfvf(hw, mbp, CSIO_MB_DEFAULT_TMO, hw->pfn, 0, CSIO_NEQ,
+ CSIO_NETH_CTRL, CSIO_NIQ_FLINT, 0, 0, CSIO_NVI, CSIO_CMASK,
+ CSIO_PMASK, CSIO_NEXACTF, CSIO_R_CAPS, CSIO_WX_CAPS, NULL);
+
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "Issue of FW_PFVF_CMD failed!\n");
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ retval = csio_mb_fw_retval(mbp);
+ if (retval != FW_SUCCESS) {
+ csio_err(hw, "FW_PFVF_CMD returned 0x%x!\n", retval);
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ mempool_free(mbp, hw->mb_mempool);
+
+ return CSIO_SUCCESS;
+}
+
+/*
+ * csio_enable_ports - Bring up all available ports.
+ * @hw: HW module.
+ *
+ */
+static csio_retval_t
+csio_enable_ports(struct csio_hw *hw)
+{
+ struct csio_mb *mbp;
+ enum fw_retval retval;
+ uint8_t portid;
+ int i;
+
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp) {
+ csio_inc_stats(hw, n_err_nomem);
+ return CSIO_NOMEM;
+ }
+
+ for (i = 0; i < hw->num_pports; i++) {
+ portid = hw->pport[i].portid;
+
+ /* Read PORT information */
+ csio_mb_port(hw, mbp, CSIO_MB_DEFAULT_TMO, portid,
+ CSIO_FALSE, 0, 0, NULL);
+
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "failed to issue FW_PORT_CMD(r) port:%d\n",
+ portid);
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ csio_mb_process_read_port_rsp(hw, mbp, &retval,
+ &hw->pport[i].pcap);
+ if (retval != FW_SUCCESS) {
+ csio_err(hw, "FW_PORT_CMD(r) port:%d failed: 0x%x\n",
+ portid, retval);
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ /* Write back PORT information */
+ csio_mb_port(hw, mbp, CSIO_MB_DEFAULT_TMO, portid,
+ CSIO_TRUE, (PAUSE_RX | PAUSE_TX),
+ hw->pport[i].pcap, NULL);
+
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "failed to issue FW_PORT_CMD(w) port:%d\n",
+ portid);
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ retval = csio_mb_fw_retval(mbp);
+ if (retval != FW_SUCCESS) {
+ csio_err(hw, "FW_PORT_CMD(w) port:%d failed :0x%x\n",
+ portid, retval);
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ } /* For all ports */
+
+ mempool_free(mbp, hw->mb_mempool);
+
+ return CSIO_SUCCESS;
+}
+
+/*
+ * csio_get_fcoe_resinfo - Read fcoe fw resource info.
+ * @hw: HW module
+ * Issued with lock held.
+ */
+static csio_retval_t
+csio_get_fcoe_resinfo(struct csio_hw *hw)
+{
+ struct csio_fcoe_res_info *res_info = &hw->fres_info;
+ struct fw_fcoe_res_info_cmd *rsp;
+ struct csio_mb *mbp;
+ enum fw_retval retval;
+
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp) {
+ csio_inc_stats(hw, n_err_nomem);
+ return CSIO_NOMEM;
+ }
+
+ /* Get FCoE FW resource information */
+ csio_fcoe_read_res_info_init_mb(hw, mbp, CSIO_MB_DEFAULT_TMO, NULL);
+
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "failed to issue FW_FCOE_RES_INFO_CMD\n");
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ rsp = (struct fw_fcoe_res_info_cmd *)(mbp->mb);
+ retval = FW_CMD_RETVAL_GET(ntohl(rsp->retval_len16));
+ if (retval != FW_SUCCESS) {
+ csio_err(hw, "FW_FCOE_RES_INFO_CMD failed with ret x%x\n",
+ retval);
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ res_info->e_d_tov = ntohs(rsp->e_d_tov);
+ res_info->r_a_tov_seq = ntohs(rsp->r_a_tov_seq);
+ res_info->r_a_tov_els = ntohs(rsp->r_a_tov_els);
+ res_info->r_r_tov = ntohs(rsp->r_r_tov);
+ res_info->max_xchgs = ntohl(rsp->max_xchgs);
+ res_info->max_ssns = ntohl(rsp->max_ssns);
+ res_info->used_xchgs = ntohl(rsp->used_xchgs);
+ res_info->used_ssns = ntohl(rsp->used_ssns);
+ res_info->max_fcfs = ntohl(rsp->max_fcfs);
+ res_info->max_vnps = ntohl(rsp->max_vnps);
+ res_info->used_fcfs = ntohl(rsp->used_fcfs);
+ res_info->used_vnps = ntohl(rsp->used_vnps);
+
+ csio_dbg(hw, "max ssns:%d max xchgs:%d\n", res_info->max_ssns,
+ res_info->max_xchgs);
+ mempool_free(mbp, hw->mb_mempool);
+
+ return CSIO_SUCCESS;
+}
+
+static csio_retval_t
+csio_hw_check_fwconfig(struct csio_hw *hw, u32 *param)
+{
+ struct csio_mb *mbp;
+ enum fw_retval retval;
+ u32 _param[1];
+
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp) {
+ csio_inc_stats(hw, n_err_nomem);
+ return CSIO_NOMEM;
+ }
+
+ /*
+ * Find out whether we're dealing with a version of
+ * the firmware which has configuration file support.
+ */
+ _param[0] = (FW_PARAMS_MNEM(FW_PARAMS_MNEM_DEV) |
+ FW_PARAMS_PARAM_X(FW_PARAMS_PARAM_DEV_CF));
+
+ csio_mb_params(hw, mbp, CSIO_MB_DEFAULT_TMO, hw->pfn, 0,
+ ARRAY_SIZE(_param), _param, NULL, CSIO_FALSE, NULL);
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "Issue of FW_PARAMS_CMD(read) failed!\n");
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ csio_mb_process_read_params_rsp(hw, mbp, &retval,
+ ARRAY_SIZE(_param), _param);
+ if (retval != FW_SUCCESS) {
+ csio_err(hw, "FW_PARAMS_CMD(read) failed with ret:0x%x!\n",
+ retval);
+ mempool_free(mbp, hw->mb_mempool);
+ return CSIO_INVAL;
+ }
+
+ mempool_free(mbp, hw->mb_mempool);
+ *param = _param[0];
+
+ return CSIO_SUCCESS;
+}
+
+static csio_retval_t
+csio_hw_flash_config(struct csio_hw *hw, u32 *fw_cfg_param, char *path)
+{
+ csio_retval_t ret = CSIO_SUCCESS;
+ const struct firmware *cf;
+ struct pci_dev *pci_dev = hw->pdev;
+ struct device *dev = &pci_dev->dev;
+
+ unsigned int mtype = 0, maddr = 0;
+ uint32_t *cfg_data;
+ int value_to_add = 0;
+
+ if (request_firmware(&cf, CSIO_CF_FNAME, dev) < 0) {
+ csio_err(hw, "could not find config file " CSIO_CF_FNAME
+ ",err: %d\n", ret);
+ return CSIO_NOSUPP;
+ }
+
+ if (cf->size%4 != 0)
+ value_to_add = 4 - (cf->size % 4);
+
+ cfg_data = kzalloc(cf->size+value_to_add, GFP_KERNEL);
+ if (cfg_data == NULL)
+ return CSIO_NOMEM;
+
+ memcpy((void *)cfg_data, (const void *)cf->data, cf->size);
+
+ if (csio_hw_check_fwconfig(hw, fw_cfg_param) != CSIO_SUCCESS)
+ return CSIO_INVAL;
+
+ mtype = FW_PARAMS_PARAM_Y_GET(*fw_cfg_param);
+ maddr = FW_PARAMS_PARAM_Z_GET(*fw_cfg_param) << 16;
+
+ ret = csio_memory_write(hw, mtype, maddr,
+ cf->size + value_to_add, cfg_data);
+ if (ret == CSIO_SUCCESS) {
+ csio_info(hw, "config file upgraded to " CSIO_CF_FNAME "\n");
+ strncpy(path, "/lib/firmware/" CSIO_CF_FNAME, 64);
+ }
+
+ kfree(cfg_data);
+ release_firmware(cf);
+
+ return ret;
+}
+
+/*
+ * HW initialization: contact FW, obtain config, perform basic init.
+ *
+ * If the firmware we're dealing with has Configuration File support, then
+ * we use that to perform all configuration -- either using the configuration
+ * file stored in flash on the adapter or using a filesystem-local file
+ * if available.
+ *
+ * If we don't have configuration file support in the firmware, then we'll
+ * have to set things up the old fashioned way with hard-coded register
+ * writes and firmware commands ...
+ */
+
+/*
+ * Attempt to initialize the HW via a Firmware Configuration File.
+ */
+static csio_retval_t
+csio_hw_use_fwconfig(struct csio_hw *hw, int reset, u32 *fw_cfg_param)
+{
+ unsigned int mtype, maddr;
+ csio_retval_t rv;
+ uint32_t finiver, finicsum, cfcsum;
+ int using_flash;
+ char path[64];
+
+ /*
+ * Reset device if necessary
+ */
+ if (reset) {
+ rv = csio_do_reset(hw, CSIO_TRUE);
+ if (rv != CSIO_SUCCESS)
+ goto bye;
+ }
+
+ /*
+ * If we have a configuration file in host ,
+ * then use that. Otherwise, use the configuration file stored
+ * in the HW flash ...
+ */
+ spin_unlock_irq(&hw->lock);
+ rv = csio_hw_flash_config(hw, fw_cfg_param, path);
+ spin_lock_irq(&hw->lock);
+ if (rv != CSIO_SUCCESS) {
+ if (rv == CSIO_NOSUPP) {
+ /*
+ * config file was not found. Use default
+ * config file from flash.
+ */
+ mtype = FW_MEMTYPE_CF_FLASH;
+ maddr = csio_hw_flash_cfg_addr(hw);
+ using_flash = 1;
+ } else {
+ /*
+ * we revert back to the hardwired config if
+ * flashing failed.
+ */
+ goto bye;
+ }
+ } else {
+ mtype = FW_PARAMS_PARAM_Y_GET(*fw_cfg_param);
+ maddr = FW_PARAMS_PARAM_Z_GET(*fw_cfg_param) << 16;
+ using_flash = 0;
+ }
+
+ hw->cfg_store = (uint8_t)mtype;
+
+ /*
+ * Issue a Capability Configuration command to the firmware to get it
+ * to parse the Configuration File.
+ */
+ rv = csio_hw_fw_config_file(hw, mtype, maddr, &finiver,
+ &finicsum, &cfcsum);
+ if (rv != CSIO_SUCCESS)
+ goto bye;
+
+ hw->cfg_finiver = finiver;
+ hw->cfg_finicsum = finicsum;
+ hw->cfg_cfcsum = cfcsum;
+ hw->cfg_csum_status = CSIO_TRUE;
+
+ if (finicsum != cfcsum) {
+ csio_warn(hw,
+ "Config File checksum mismatch: csum=%#x, computed=%#x\n",
+ finicsum, cfcsum);
+
+ hw->cfg_csum_status = CSIO_FALSE;
+ }
+
+ /*
+ * Note that we're operating with parameters
+ * not supplied by the driver, rather than from hard-wired
+ * initialization constants buried in the driver.
+ */
+ hw->flags |= CSIO_HWF_USING_SOFT_PARAMS;
+
+ /* device parameters */
+ rv = csio_get_device_params(hw);
+ if (rv != CSIO_SUCCESS)
+ goto bye;
+
+ /* Configure SGE */
+ csio_wr_sge_init(hw);
+
+ /*
+ * And finally tell the firmware to initialize itself using the
+ * parameters from the Configuration File.
+ */
+ /* Post event to notify completion of configuration */
+ csio_post_event(&hw->sm, CSIO_HWE_INIT);
+
+ csio_info(hw,
+ "Firmware Configuration File %s, version %#x, computed checksum %#x\n",
+ (using_flash ? "in device FLASH" : path), finiver, cfcsum);
+
+ return 0;
+
+ /*
+ * Something bad happened. Return the error ...
+ */
+bye:
+ hw->flags &= ~CSIO_HWF_USING_SOFT_PARAMS;
+ csio_dbg(hw, "Configuration file error %d\n", rv);
+ return rv;
+}
+
+/*
+ * Attempt to initialize the adapter via hard-coded, driver supplied
+ * parameters ...
+ */
+static int
+csio_hw_no_fwconfig(struct csio_hw *hw, int reset)
+{
+ csio_retval_t rv;
+ /*
+ * Reset device if necessary
+ */
+ if (reset) {
+ rv = csio_do_reset(hw, CSIO_TRUE);
+ if (rv != CSIO_SUCCESS)
+ goto out;
+ }
+
+ /* Get and set device capabilities */
+ rv = csio_config_device_caps(hw);
+ if (rv != CSIO_SUCCESS)
+ goto out;
+
+ /* Config Global RSS command */
+ rv = csio_config_global_rss(hw);
+ if (rv != CSIO_SUCCESS)
+ goto out;
+
+ /* Configure PF/VF capabilities of device */
+ rv = csio_config_pfvf(hw);
+ if (rv != CSIO_SUCCESS)
+ goto out;
+
+ /* device parameters */
+ rv = csio_get_device_params(hw);
+ if (rv != CSIO_SUCCESS)
+ goto out;
+
+ /* Configure SGE */
+ csio_wr_sge_init(hw);
+
+ /* Post event to notify completion of configuration */
+ csio_post_event(&hw->sm, CSIO_HWE_INIT);
+
+out:
+ return rv;
+}
+
+/*
+ * Returns CSIO_INVAL if attempts to flash the firmware failed
+ * else returns CSIO_SUCCESS,
+ * if flashing was not attempted because the card had the
+ * latest firmware CSIO_CANCELLED is returned
+ */
+static int
+csio_hw_flash_fw(struct csio_hw *hw)
+{
+ int ret = CSIO_CANCELLED;
+ const struct firmware *fw;
+ const struct fw_hdr *hdr;
+ u32 fw_ver;
+ struct pci_dev *pci_dev = hw->pdev;
+ struct device *dev = &pci_dev->dev ;
+
+ if (request_firmware(&fw, CSIO_FW_FNAME, dev) < 0) {
+ csio_err(hw, "could not find firmware image " CSIO_FW_FNAME
+ ",err: %d\n", ret);
+ return CSIO_INVAL;
+ }
+
+ hdr = (const struct fw_hdr *)fw->data;
+ fw_ver = ntohl(hdr->fw_ver);
+ if (FW_HDR_FW_VER_MAJOR_GET(fw_ver) != FW_VERSION_MAJOR)
+ return CSIO_INVAL; /* wrong major version, won't do */
+
+ /*
+ * If the flash FW is unusable or we found something newer, load it.
+ */
+ if (FW_HDR_FW_VER_MAJOR_GET(hw->fwrev) != FW_VERSION_MAJOR ||
+ fw_ver > hw->fwrev) {
+ ret = csio_hw_fw_upgrade(hw, hw->pfn, fw->data, fw->size,
+ /*force=*/false);
+ if (!ret)
+ csio_info(hw, "firmware upgraded to version %pI4 from "
+ CSIO_FW_FNAME "\n", &hdr->fw_ver);
+ else
+ csio_err(hw, "firmware upgrade failed! err=%d\n", -ret);
+ }
+
+ release_firmware(fw);
+ return ret;
+}
+
+
+/*
+ * csio_hw_configure - Configure HW
+ * @hw - HW module
+ *
+ */
+static void
+csio_hw_configure(struct csio_hw *hw)
+{
+ int reset = 1;
+ csio_retval_t rv;
+ u32 param[1];
+
+ rv = csio_hw_dev_ready(hw);
+ if (rv != CSIO_SUCCESS) {
+ csio_inc_stats(hw, n_err_fatal);
+ csio_post_event(&hw->sm, CSIO_HWE_FATAL);
+ goto out;
+ }
+
+ /* HW version */
+ hw->chip_ver = (char)csio_rd_reg32(hw, PL_REV);
+
+ /* Needed for FW download */
+ rv = csio_hw_get_flash_params(hw);
+ if (rv != CSIO_SUCCESS) {
+ csio_err(hw, "Failed to get serial flash params rv:%d\n", rv);
+ csio_post_event(&hw->sm, CSIO_HWE_FATAL);
+ goto out;
+ }
+
+ /* Set pci completion timeout value to 4 seconds. */
+ csio_set_pcie_completion_timeout(hw, 0xd);
+
+ csio_hw_set_mem_win(hw);
+
+ rv = csio_hw_get_fw_version(hw, &hw->fwrev);
+ if (rv != CSIO_SUCCESS)
+ goto out;
+
+ csio_hw_print_fw_version(hw, "Firmware revision");
+
+ rv = csio_do_hello(hw, &hw->fw_state);
+ if (rv != CSIO_SUCCESS) {
+ csio_inc_stats(hw, n_err_fatal);
+ csio_post_event(&hw->sm, CSIO_HWE_FATAL);
+ goto out;
+ }
+
+ /* Read vpd */
+ rv = csio_hw_get_vpd_params(hw, &hw->vpd);
+ if (rv != CSIO_SUCCESS)
+ goto out;
+
+ if (csio_is_hw_master(hw) && hw->fw_state != CSIO_DEV_STATE_INIT) {
+ rv = csio_hw_check_fw_version(hw);
+ if (rv == CSIO_INVAL) {
+
+ /* Do firmware update */
+ spin_unlock_irq(&hw->lock);
+ rv = csio_hw_flash_fw(hw);
+ spin_lock_irq(&hw->lock);
+
+ if (rv == CSIO_SUCCESS) {
+ reset = 0;
+ /*
+ * Note that the chip was reset as part of the
+ * firmware upgrade so we don't reset it again
+ * below and grab the new firmware version.
+ */
+ rv = csio_hw_check_fw_version(hw);
+ }
+ }
+ /*
+ * If the firmware doesn't support Configuration
+ * Files, use the old Driver-based, hard-wired
+ * initialization. Otherwise, try using the
+ * Configuration File support and fall back to the
+ * Driver-based initialization if there's no
+ * Configuration File found.
+ */
+ if (csio_hw_check_fwconfig(hw, param) == CSIO_SUCCESS) {
+ rv = csio_hw_use_fwconfig(hw, reset, param);
+ if (rv == CSIO_NOSUPP)
+ goto out;
+ if (rv != CSIO_SUCCESS) {
+ csio_info(hw,
+ "No Configuration File present "
+ "on adapter. Using hard-wired "
+ "configuration parameters.\n");
+ rv = csio_hw_no_fwconfig(hw, reset);
+ }
+ } else {
+ rv = csio_hw_no_fwconfig(hw, reset);
+ }
+
+ if (rv != CSIO_SUCCESS)
+ goto out;
+
+ } else {
+ if (hw->fw_state == CSIO_DEV_STATE_INIT) {
+
+ /* device parameters */
+ rv = csio_get_device_params(hw);
+ if (rv != CSIO_SUCCESS)
+ goto out;
+
+ /* Get device capabilities */
+ rv = csio_config_device_caps(hw);
+ if (rv != CSIO_SUCCESS)
+ goto out;
+
+ /* Configure SGE */
+ csio_wr_sge_init(hw);
+
+ /* Post event to notify completion of configuration */
+ csio_post_event(&hw->sm, CSIO_HWE_INIT);
+ goto out;
+ }
+ } /* if not master */
+
+out:
+ return;
+}
+
+/*
+ * csio_hw_initialize - Initialize HW
+ * @hw - HW module
+ *
+ */
+static void
+csio_hw_initialize(struct csio_hw *hw)
+{
+ struct csio_mb *mbp;
+ enum fw_retval retval;
+ csio_retval_t rv;
+ int i;
+
+ if (csio_is_hw_master(hw) && hw->fw_state != CSIO_DEV_STATE_INIT) {
+ mbp = mempool_alloc(hw->mb_mempool, GFP_ATOMIC);
+ if (!mbp)
+ goto out;
+
+ csio_mb_initialize(hw, mbp, CSIO_MB_DEFAULT_TMO, NULL);
+
+ if (csio_mb_issue(hw, mbp)) {
+ csio_err(hw, "Issue of FW_INITIALIZE_CMD failed!\n");
+ goto free_and_out;
+ }
+
+ retval = csio_mb_fw_retval(mbp);
+ if (retval != FW_SUCCESS) {
+ csio_err(hw, "FW_INITIALIZE_CMD returned 0x%x!\n",
+ retval);
+ goto free_and_out;
+ }
+
+ mempool_free(mbp, hw->mb_mempool);
+ }
+
+ rv = csio_get_fcoe_resinfo(hw);
+ if (rv != CSIO_SUCCESS) {
+ csio_err(hw, "Failed to read fcoe resource info: %d\n", rv);
+ goto out;
+ }
+
+ spin_unlock_irq(&hw->lock);
+ rv = csio_config_queues(hw);
+ spin_lock_irq(&hw->lock);
+
+ if (rv != CSIO_SUCCESS) {
+ csio_err(hw, "Config of queues failed!: %d\n", rv);
+ goto out;
+ }
+
+ for (i = 0; i < hw->num_pports; i++)
+ hw->pport[i].mod_type = FW_PORT_MOD_TYPE_NA;
+
+ if (csio_is_hw_master(hw) && hw->fw_state != CSIO_DEV_STATE_INIT) {
+ rv = csio_enable_ports(hw);
+ if (rv != CSIO_SUCCESS) {
+ csio_err(hw, "Failed to enable ports: %d\n", rv);
+ goto out;
+ }
+ }
+
+ csio_post_event(&hw->sm, CSIO_HWE_INIT_DONE);
+ return;
+
+free_and_out:
+ mempool_free(mbp, hw->mb_mempool);
+out:
+ return;
+}
+
+#define PF_INTR_MASK (PFSW | PFCIM)
+
+/*
+ * csio_hw_intr_enable - Enable HW interrupts
+ * @hw: Pointer to HW module.
+ *
+ * Enable interrupts in HW registers.
+ */
+static void
+csio_hw_intr_enable(struct csio_hw *hw)
+{
+ uint16_t vec = (uint16_t)csio_get_mb_intr_idx(csio_hw_to_mbm(hw));
+ uint32_t pf = SOURCEPF_GET(csio_rd_reg32(hw, PL_WHOAMI));
+ uint32_t pl = csio_rd_reg32(hw, PL_INT_ENABLE);
+
+ /*
+ * Set aivec for MSI/MSIX. PCIE_PF_CFG.INTXType is set up
+ * by FW, so do nothing for INTX.
+ */
+ if (hw->intr_mode == CSIO_IM_MSIX)
+ csio_set_reg_field(hw, MYPF_REG(PCIE_PF_CFG),
+ AIVEC(AIVEC_MASK), vec);
+ else if (hw->intr_mode == CSIO_IM_MSI)
+ csio_set_reg_field(hw, MYPF_REG(PCIE_PF_CFG),
+ AIVEC(AIVEC_MASK), 0);
+
+ csio_wr_reg32(hw, PF_INTR_MASK, MYPF_REG(PL_PF_INT_ENABLE));
+
+ /* Turn on MB interrupts - this will internally flush PIO as well */
+ csio_mb_intr_enable(hw);
+
+ /* These are common registers - only a master can modify them */
+ if (csio_is_hw_master(hw)) {
+ /*
+ * Disable the Serial FLASH interrupt, if enabled!
+ */
+ pl &= (~SF);
+ csio_wr_reg32(hw, pl, PL_INT_ENABLE);
+
+ csio_wr_reg32(hw, ERR_CPL_EXCEED_IQE_SIZE |
+ EGRESS_SIZE_ERR | ERR_INVALID_CIDX_INC |
+ ERR_CPL_OPCODE_0 | ERR_DROPPED_DB |
+ ERR_DATA_CPL_ON_HIGH_QID1 |
+ ERR_DATA_CPL_ON_HIGH_QID0 | ERR_BAD_DB_PIDX3 |
+ ERR_BAD_DB_PIDX2 | ERR_BAD_DB_PIDX1 |
+ ERR_BAD_DB_PIDX0 | ERR_ING_CTXT_PRIO |
+ ERR_EGR_CTXT_PRIO | INGRESS_SIZE_ERR,
+ SGE_INT_ENABLE3);
+ csio_set_reg_field(hw, PL_INT_MAP0, 0, 1 << pf);
+ }
+
+ hw->flags |= CSIO_HWF_HW_INTR_ENABLED;
+
+}
+
+/*
+ * csio_hw_intr_disable - Disable HW interrupts
+ * @hw: Pointer to HW module.
+ *
+ * Turn off Mailbox and PCI_PF_CFG interrupts.
+ */
+void
+csio_hw_intr_disable(struct csio_hw *hw)
+{
+ uint32_t pf = SOURCEPF_GET(csio_rd_reg32(hw, PL_WHOAMI));
+
+ if (!(hw->flags & CSIO_HWF_HW_INTR_ENABLED))
+ return;
+
+ hw->flags &= ~CSIO_HWF_HW_INTR_ENABLED;
+
+ csio_wr_reg32(hw, 0, MYPF_REG(PL_PF_INT_ENABLE));
+ if (csio_is_hw_master(hw))
+ csio_set_reg_field(hw, PL_INT_MAP0, 1 << pf, 0);
+
+ /* Turn off MB interrupts */
+ csio_mb_intr_disable(hw);
+
+}
+
+static void
+csio_hw_fatal_err(struct csio_hw *hw)
+{
+ csio_set_reg_field(hw, SGE_CONTROL, GLOBALENABLE, 0);
+ csio_hw_intr_disable(hw);
+
+ /* Do not reset HW, we may need FW state for debugging */
+ csio_fatal(hw, "HW Fatal error encountered!\n");
+}
+
+/*****************************************************************************/
+/* START: HW SM */
+/*****************************************************************************/
+/*
+ * csio_hws_uninit - Uninit state
+ * @hw - HW module
+ * @evt - Event
+ *
+ */
+static void
+csio_hws_uninit(struct csio_hw *hw, enum csio_hw_ev evt)
+{
+ hw->prev_evt = hw->cur_evt;
+ hw->cur_evt = evt;
+ csio_inc_stats(hw, n_evt_sm[evt]);
+
+ switch (evt) {
+
+ case CSIO_HWE_CFG:
+ csio_set_state(&hw->sm, csio_hws_configuring);
+ csio_hw_configure(hw);
+ break;
+
+ default:
+ csio_inc_stats(hw, n_evt_unexp);
+ break;
+ }
+}
+
+/*
+ * csio_hws_configuring - Configuring state
+ * @hw - HW module
+ * @evt - Event
+ *
+ */
+static void
+csio_hws_configuring(struct csio_hw *hw, enum csio_hw_ev evt)
+{
+ hw->prev_evt = hw->cur_evt;
+ hw->cur_evt = evt;
+ csio_inc_stats(hw, n_evt_sm[evt]);
+
+ switch (evt) {
+
+ case CSIO_HWE_INIT:
+ csio_set_state(&hw->sm, csio_hws_initializing);
+ csio_hw_initialize(hw);
+ break;
+
+ case CSIO_HWE_INIT_DONE:
+ csio_set_state(&hw->sm, csio_hws_ready);
+ /* Fan out event to all lnode SMs */
+ csio_notify_lnodes(hw, CSIO_LN_NOTIFY_HWREADY);
+ break;
+
+ case CSIO_HWE_FATAL:
+ csio_set_state(&hw->sm, csio_hws_uninit);
+ break;
+
+ case CSIO_HWE_PCI_REMOVE:
+ csio_do_bye(hw);
+ break;
+ default:
+ csio_inc_stats(hw, n_evt_unexp);
+ break;
+ }
+}
+
+/*
+ * csio_hws_initializing - Initialiazing state
+ * @hw - HW module
+ * @evt - Event
+ *
+ */
+static void
+csio_hws_initializing(struct csio_hw *hw, enum csio_hw_ev evt)
+{
+ hw->prev_evt = hw->cur_evt;
+ hw->cur_evt = evt;
+ csio_inc_stats(hw, n_evt_sm[evt]);
+
+ switch (evt) {
+
+ case CSIO_HWE_INIT_DONE:
+ csio_set_state(&hw->sm, csio_hws_ready);
+
+ /* Fan out event to all lnode SMs */
+ csio_notify_lnodes(hw, CSIO_LN_NOTIFY_HWREADY);
+
+ /* Enable interrupts */
+ csio_hw_intr_enable(hw);
+ break;
+
+ case CSIO_HWE_FATAL:
+ csio_set_state(&hw->sm, csio_hws_uninit);
+ break;
+
+ case CSIO_HWE_PCI_REMOVE:
+ csio_do_bye(hw);
+ break;
+
+ default:
+ csio_inc_stats(hw, n_evt_unexp);
+ break;
+ }
+}
+
+/*
+ * csio_hws_ready - Ready state
+ * @hw - HW module
+ * @evt - Event
+ *
+ */
+static void
+csio_hws_ready(struct csio_hw *hw, enum csio_hw_ev evt)
+{
+ /* Remember the event */
+ hw->evtflag = evt;
+
+ hw->prev_evt = hw->cur_evt;
+ hw->cur_evt = evt;
+ csio_inc_stats(hw, n_evt_sm[evt]);
+
+ switch (evt) {
+
+ case CSIO_HWE_HBA_RESET:
+ case CSIO_HWE_FW_DLOAD:
+ case CSIO_HWE_SUSPEND:
+ case CSIO_HWE_PCI_REMOVE:
+ case CSIO_HWE_PCIERR_DETECTED:
+ csio_set_state(&hw->sm, csio_hws_quiescing);
+ /* cleanup all outstanding cmds */
+ if (evt == CSIO_HWE_HBA_RESET ||
+ evt == CSIO_HWE_PCIERR_DETECTED)
+ csio_scsim_cleanup_io(csio_hw_to_scsim(hw), CSIO_FALSE);
+ else
+ csio_scsim_cleanup_io(csio_hw_to_scsim(hw), CSIO_TRUE);
+
+ csio_hw_intr_disable(hw);
+ csio_hw_mbm_cleanup(hw);
+ csio_evtq_stop(hw);
+ csio_notify_lnodes(hw, CSIO_LN_NOTIFY_HWSTOP);
+ csio_evtq_flush(hw);
+ csio_mgmtm_cleanup(csio_hw_to_mgmtm(hw));
+ csio_post_event(&hw->sm, CSIO_HWE_QUIESCED);
+ break;
+
+ case CSIO_HWE_FATAL:
+ csio_set_state(&hw->sm, csio_hws_uninit);
+ break;
+
+ default:
+ csio_inc_stats(hw, n_evt_unexp);
+ break;
+ }
+}
+
+/*
+ * csio_hws_quiescing - Quiescing state
+ * @hw - HW module
+ * @evt - Event
+ *
+ */
+static void
+csio_hws_quiescing(struct csio_hw *hw, enum csio_hw_ev evt)
+{
+ hw->prev_evt = hw->cur_evt;
+ hw->cur_evt = evt;
+ csio_inc_stats(hw, n_evt_sm[evt]);
+
+ switch (evt) {
+
+ case CSIO_HWE_QUIESCED:
+ switch (hw->evtflag) {
+
+ case CSIO_HWE_FW_DLOAD:
+ csio_set_state(&hw->sm, csio_hws_resetting);
+ /* Download firmware */
+ /* Fall through */
+
+ case CSIO_HWE_HBA_RESET:
+ csio_set_state(&hw->sm, csio_hws_resetting);
+ /* Start reset of the HBA */
+ csio_notify_lnodes(hw, CSIO_LN_NOTIFY_HWRESET);
+ csio_wr_destroy_queues(hw, CSIO_FALSE);
+ csio_do_reset(hw, CSIO_FALSE);
+ csio_post_event(&hw->sm, CSIO_HWE_HBA_RESET_DONE);
+ break;
+
+ case CSIO_HWE_PCI_REMOVE:
+ csio_set_state(&hw->sm, csio_hws_removing);
+ csio_notify_lnodes(hw, CSIO_LN_NOTIFY_HWREMOVE);
+ csio_wr_destroy_queues(hw, CSIO_TRUE);
+ /* Now send the bye command */
+ csio_do_bye(hw);
+ break;
+
+ case CSIO_HWE_SUSPEND:
+ csio_set_state(&hw->sm, csio_hws_quiesced);
+ break;
+
+ case CSIO_HWE_PCIERR_DETECTED:
+ csio_set_state(&hw->sm, csio_hws_pcierr);
+ csio_wr_destroy_queues(hw, CSIO_FALSE);
+ break;
+
+ default:
+ csio_inc_stats(hw, n_evt_unexp);
+ break;
+
+ }
+ break;
+
+ default:
+ csio_inc_stats(hw, n_evt_unexp);
+ break;
+ }
+}
+
+/*
+ * csio_hws_quiesced - Quiesced state
+ * @hw - HW module
+ * @evt - Event
+ *
+ */
+static void
+csio_hws_quiesced(struct csio_hw *hw, enum csio_hw_ev evt)
+{
+ hw->prev_evt = hw->cur_evt;
+ hw->cur_evt = evt;
+ csio_inc_stats(hw, n_evt_sm[evt]);
+
+ switch (evt) {
+
+ case CSIO_HWE_RESUME:
+ csio_set_state(&hw->sm, csio_hws_configuring);
+ csio_hw_configure(hw);
+ break;
+
+ default:
+ csio_inc_stats(hw, n_evt_unexp);
+ break;
+ }
+}
+
+/*
+ * csio_hws_resetting - HW Resetting state
+ * @hw - HW module
+ * @evt - Event
+ *
+ */
+static void
+csio_hws_resetting(struct csio_hw *hw, enum csio_hw_ev evt)
+{
+ hw->prev_evt = hw->cur_evt;
+ hw->cur_evt = evt;
+ csio_inc_stats(hw, n_evt_sm[evt]);
+
+ switch (evt) {
+
+ case CSIO_HWE_HBA_RESET_DONE:
+ csio_evtq_start(hw);
+ csio_set_state(&hw->sm, csio_hws_configuring);
+ csio_hw_configure(hw);
+ break;
+
+ default:
+ csio_inc_stats(hw, n_evt_unexp);
+ break;
+ }
+}
+
+/*
+ * csio_hws_removing - PCI Hotplug removing state
+ * @hw - HW module
+ * @evt - Event
+ *
+ */
+static void
+csio_hws_removing(struct csio_hw *hw, enum csio_hw_ev evt)
+{
+ hw->prev_evt = hw->cur_evt;
+ hw->cur_evt = evt;
+ csio_inc_stats(hw, n_evt_sm[evt]);
+
+ switch (evt) {
+ case CSIO_HWE_HBA_RESET:
+ if (!csio_is_hw_master(hw))
+ break;
+ /*
+ * The BYE should have alerady been issued, so we cant
+ * use the mailbox interface. Hence we use the PL_RST
+ * register directly.
+ */
+ csio_err(hw, "Resetting HW and waiting 2 seconds...\n");
+ csio_wr_reg32(hw, PIORSTMODE | PIORST, PL_RST);
+ mdelay(2000);
+ break;
+
+ /* Should never receive any new events */
+ default:
+ csio_inc_stats(hw, n_evt_unexp);
+ break;
+
+ }
+}
+
+/*
+ * csio_hws_pcierr - PCI Error state
+ * @hw - HW module
+ * @evt - Event
+ *
+ */
+static void
+csio_hws_pcierr(struct csio_hw *hw, enum csio_hw_ev evt)
+{
+ hw->prev_evt = hw->cur_evt;
+ hw->cur_evt = evt;
+ csio_inc_stats(hw, n_evt_sm[evt]);
+
+ switch (evt) {
+
+ case CSIO_HWE_PCIERR_SLOT_RESET:
+ csio_evtq_start(hw);
+ csio_set_state(&hw->sm, csio_hws_configuring);
+ csio_hw_configure(hw);
+ break;
+
+ default:
+ csio_inc_stats(hw, n_evt_unexp);
+ break;
+ }
+}
+
+/*****************************************************************************/
+/* END: HW SM */
+/*****************************************************************************/
+
+/* Slow path handlers */
+struct intr_info {
+ unsigned int mask; /* bits to check in interrupt status */
+ const char *msg; /* message to print or NULL */
+ short stat_idx; /* stat counter to increment or -1 */
+ unsigned short fatal; /* whether the condition reported is fatal */
+};
+
+/*
+ * csio_handle_intr_status - table driven interrupt handler
+ * @hw: HW instance
+ * @reg: the interrupt status register to process
+ * @acts: table of interrupt actions
+ *
+ * A table driven interrupt handler that applies a set of masks to an
+ * interrupt status word and performs the corresponding actions if the
+ * interrupts described by the mask have occured. The actions include
+ * optionally emitting a warning or alert message. The table is terminated
+ * by an entry specifying mask 0. Returns the number of fatal interrupt
+ * conditions.
+ */
+static int
+csio_handle_intr_status(struct csio_hw *hw, unsigned int reg,
+ const struct intr_info *acts)
+{
+ int fatal = 0;
+ unsigned int mask = 0;
+ unsigned int status = csio_rd_reg32(hw, reg);
+
+ for ( ; acts->mask; ++acts) {
+ if (!(status & acts->mask))
+ continue;
+ if (acts->fatal) {
+ fatal++;
+ csio_fatal(hw, "Fatal %s (0x%x)\n",
+ acts->msg, status & acts->mask);
+ } else if (acts->msg)
+ csio_info(hw, "%s (0x%x)\n",
+ acts->msg, status & acts->mask);
+ mask |= acts->mask;
+ }
+ status &= mask;
+ if (status) /* clear processed interrupts */
+ csio_wr_reg32(hw, status, reg);
+ return fatal;
+}
+
+/*
+ * Interrupt handler for the PCIE module.
+ */
+static void
+csio_pcie_intr_handler(struct csio_hw *hw)
+{
+ static struct intr_info sysbus_intr_info[] = {
+ { RNPP, "RXNP array parity error", -1, 1 },
+ { RPCP, "RXPC array parity error", -1, 1 },
+ { RCIP, "RXCIF array parity error", -1, 1 },
+ { RCCP, "Rx completions control array parity error", -1, 1 },
+ { RFTP, "RXFT array parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+ static struct intr_info pcie_port_intr_info[] = {
+ { TPCP, "TXPC array parity error", -1, 1 },
+ { TNPP, "TXNP array parity error", -1, 1 },
+ { TFTP, "TXFT array parity error", -1, 1 },
+ { TCAP, "TXCA array parity error", -1, 1 },
+ { TCIP, "TXCIF array parity error", -1, 1 },
+ { RCAP, "RXCA array parity error", -1, 1 },
+ { OTDD, "outbound request TLP discarded", -1, 1 },
+ { RDPE, "Rx data parity error", -1, 1 },
+ { TDUE, "Tx uncorrectable data error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+ static struct intr_info pcie_intr_info[] = {
+ { MSIADDRLPERR, "MSI AddrL parity error", -1, 1 },
+ { MSIADDRHPERR, "MSI AddrH parity error", -1, 1 },
+ { MSIDATAPERR, "MSI data parity error", -1, 1 },
+ { MSIXADDRLPERR, "MSI-X AddrL parity error", -1, 1 },
+ { MSIXADDRHPERR, "MSI-X AddrH parity error", -1, 1 },
+ { MSIXDATAPERR, "MSI-X data parity error", -1, 1 },
+ { MSIXDIPERR, "MSI-X DI parity error", -1, 1 },
+ { PIOCPLPERR, "PCI PIO completion FIFO parity error", -1, 1 },
+ { PIOREQPERR, "PCI PIO request FIFO parity error", -1, 1 },
+ { TARTAGPERR, "PCI PCI target tag FIFO parity error", -1, 1 },
+ { CCNTPERR, "PCI CMD channel count parity error", -1, 1 },
+ { CREQPERR, "PCI CMD channel request parity error", -1, 1 },
+ { CRSPPERR, "PCI CMD channel response parity error", -1, 1 },
+ { DCNTPERR, "PCI DMA channel count parity error", -1, 1 },
+ { DREQPERR, "PCI DMA channel request parity error", -1, 1 },
+ { DRSPPERR, "PCI DMA channel response parity error", -1, 1 },
+ { HCNTPERR, "PCI HMA channel count parity error", -1, 1 },
+ { HREQPERR, "PCI HMA channel request parity error", -1, 1 },
+ { HRSPPERR, "PCI HMA channel response parity error", -1, 1 },
+ { CFGSNPPERR, "PCI config snoop FIFO parity error", -1, 1 },
+ { FIDPERR, "PCI FID parity error", -1, 1 },
+ { INTXCLRPERR, "PCI INTx clear parity error", -1, 1 },
+ { MATAGPERR, "PCI MA tag parity error", -1, 1 },
+ { PIOTAGPERR, "PCI PIO tag parity error", -1, 1 },
+ { RXCPLPERR, "PCI Rx completion parity error", -1, 1 },
+ { RXWRPERR, "PCI Rx write parity error", -1, 1 },
+ { RPLPERR, "PCI replay buffer parity error", -1, 1 },
+ { PCIESINT, "PCI core secondary fault", -1, 1 },
+ { PCIEPINT, "PCI core primary fault", -1, 1 },
+ { UNXSPLCPLERR, "PCI unexpected split completion error", -1,
+ 0 },
+ { 0, NULL, 0, 0 }
+ };
+
+ int fat;
+
+ fat = csio_handle_intr_status(hw,
+ PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS,
+ sysbus_intr_info) +
+ csio_handle_intr_status(hw,
+ PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS,
+ pcie_port_intr_info) +
+ csio_handle_intr_status(hw, PCIE_INT_CAUSE, pcie_intr_info);
+ if (fat)
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * TP interrupt handler.
+ */
+static void csio_tp_intr_handler(struct csio_hw *hw)
+{
+ static struct intr_info tp_intr_info[] = {
+ { 0x3fffffff, "TP parity error", -1, 1 },
+ { FLMTXFLSTEMPTY, "TP out of Tx pages", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+
+ if (csio_handle_intr_status(hw, TP_INT_CAUSE, tp_intr_info))
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * SGE interrupt handler.
+ */
+static void csio_sge_intr_handler(struct csio_hw *hw)
+{
+ uint64_t v;
+
+ static struct intr_info sge_intr_info[] = {
+ { ERR_CPL_EXCEED_IQE_SIZE,
+ "SGE received CPL exceeding IQE size", -1, 1 },
+ { ERR_INVALID_CIDX_INC,
+ "SGE GTS CIDX increment too large", -1, 0 },
+ { ERR_CPL_OPCODE_0, "SGE received 0-length CPL", -1, 0 },
+ { ERR_DROPPED_DB, "SGE doorbell dropped", -1, 0 },
+ { ERR_DATA_CPL_ON_HIGH_QID1 | ERR_DATA_CPL_ON_HIGH_QID0,
+ "SGE IQID > 1023 received CPL for FL", -1, 0 },
+ { ERR_BAD_DB_PIDX3, "SGE DBP 3 pidx increment too large", -1,
+ 0 },
+ { ERR_BAD_DB_PIDX2, "SGE DBP 2 pidx increment too large", -1,
+ 0 },
+ { ERR_BAD_DB_PIDX1, "SGE DBP 1 pidx increment too large", -1,
+ 0 },
+ { ERR_BAD_DB_PIDX0, "SGE DBP 0 pidx increment too large", -1,
+ 0 },
+ { ERR_ING_CTXT_PRIO,
+ "SGE too many priority ingress contexts", -1, 0 },
+ { ERR_EGR_CTXT_PRIO,
+ "SGE too many priority egress contexts", -1, 0 },
+ { INGRESS_SIZE_ERR, "SGE illegal ingress QID", -1, 0 },
+ { EGRESS_SIZE_ERR, "SGE illegal egress QID", -1, 0 },
+ { 0, NULL, 0, 0 }
+ };
+
+ v = (uint64_t)csio_rd_reg32(hw, SGE_INT_CAUSE1) |
+ ((uint64_t)csio_rd_reg32(hw, SGE_INT_CAUSE2) << 32);
+ if (v) {
+ csio_fatal(hw, "SGE parity error (%#llx)\n",
+ (unsigned long long)v);
+ csio_wr_reg32(hw, (uint32_t)(v & 0xFFFFFFFF),
+ SGE_INT_CAUSE1);
+ csio_wr_reg32(hw, (uint32_t)(v >> 32), SGE_INT_CAUSE2);
+ }
+
+ v |= csio_handle_intr_status(hw, SGE_INT_CAUSE3, sge_intr_info);
+
+ if (csio_handle_intr_status(hw, SGE_INT_CAUSE3, sge_intr_info) ||
+ v != 0)
+ csio_hw_fatal_err(hw);
+}
+
+#define CIM_OBQ_INTR (OBQULP0PARERR | OBQULP1PARERR | OBQULP2PARERR |\
+ OBQULP3PARERR | OBQSGEPARERR | OBQNCSIPARERR)
+#define CIM_IBQ_INTR (IBQTP0PARERR | IBQTP1PARERR | IBQULPPARERR |\
+ IBQSGEHIPARERR | IBQSGELOPARERR | IBQNCSIPARERR)
+
+/*
+ * CIM interrupt handler.
+ */
+static void csio_cim_intr_handler(struct csio_hw *hw)
+{
+ static struct intr_info cim_intr_info[] = {
+ { PREFDROPINT, "CIM control register prefetch drop", -1, 1 },
+ { CIM_OBQ_INTR, "CIM OBQ parity error", -1, 1 },
+ { CIM_IBQ_INTR, "CIM IBQ parity error", -1, 1 },
+ { MBUPPARERR, "CIM mailbox uP parity error", -1, 1 },
+ { MBHOSTPARERR, "CIM mailbox host parity error", -1, 1 },
+ { TIEQINPARERRINT, "CIM TIEQ outgoing parity error", -1, 1 },
+ { TIEQOUTPARERRINT, "CIM TIEQ incoming parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+ static struct intr_info cim_upintr_info[] = {
+ { RSVDSPACEINT, "CIM reserved space access", -1, 1 },
+ { ILLTRANSINT, "CIM illegal transaction", -1, 1 },
+ { ILLWRINT, "CIM illegal write", -1, 1 },
+ { ILLRDINT, "CIM illegal read", -1, 1 },
+ { ILLRDBEINT, "CIM illegal read BE", -1, 1 },
+ { ILLWRBEINT, "CIM illegal write BE", -1, 1 },
+ { SGLRDBOOTINT, "CIM single read from boot space", -1, 1 },
+ { SGLWRBOOTINT, "CIM single write to boot space", -1, 1 },
+ { BLKWRBOOTINT, "CIM block write to boot space", -1, 1 },
+ { SGLRDFLASHINT, "CIM single read from flash space", -1, 1 },
+ { SGLWRFLASHINT, "CIM single write to flash space", -1, 1 },
+ { BLKWRFLASHINT, "CIM block write to flash space", -1, 1 },
+ { SGLRDEEPROMINT, "CIM single EEPROM read", -1, 1 },
+ { SGLWREEPROMINT, "CIM single EEPROM write", -1, 1 },
+ { BLKRDEEPROMINT, "CIM block EEPROM read", -1, 1 },
+ { BLKWREEPROMINT, "CIM block EEPROM write", -1, 1 },
+ { SGLRDCTLINT , "CIM single read from CTL space", -1, 1 },
+ { SGLWRCTLINT , "CIM single write to CTL space", -1, 1 },
+ { BLKRDCTLINT , "CIM block read from CTL space", -1, 1 },
+ { BLKWRCTLINT , "CIM block write to CTL space", -1, 1 },
+ { SGLRDPLINT , "CIM single read from PL space", -1, 1 },
+ { SGLWRPLINT , "CIM single write to PL space", -1, 1 },
+ { BLKRDPLINT , "CIM block read from PL space", -1, 1 },
+ { BLKWRPLINT , "CIM block write to PL space", -1, 1 },
+ { REQOVRLOOKUPINT , "CIM request FIFO overwrite", -1, 1 },
+ { RSPOVRLOOKUPINT , "CIM response FIFO overwrite", -1, 1 },
+ { TIMEOUTINT , "CIM PIF timeout", -1, 1 },
+ { TIMEOUTMAINT , "CIM PIF MA timeout", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+
+ int fat;
+
+ fat = csio_handle_intr_status(hw, CIM_HOST_INT_CAUSE,
+ cim_intr_info) +
+ csio_handle_intr_status(hw, CIM_HOST_UPACC_INT_CAUSE,
+ cim_upintr_info);
+ if (fat)
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * ULP RX interrupt handler.
+ */
+static void csio_ulprx_intr_handler(struct csio_hw *hw)
+{
+ static struct intr_info ulprx_intr_info[] = {
+ { 0x1800000, "ULPRX context error", -1, 1 },
+ { 0x7fffff, "ULPRX parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+
+ if (csio_handle_intr_status(hw, ULP_RX_INT_CAUSE, ulprx_intr_info))
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * ULP TX interrupt handler.
+ */
+static void csio_ulptx_intr_handler(struct csio_hw *hw)
+{
+ static struct intr_info ulptx_intr_info[] = {
+ { PBL_BOUND_ERR_CH3, "ULPTX channel 3 PBL out of bounds", -1,
+ 0 },
+ { PBL_BOUND_ERR_CH2, "ULPTX channel 2 PBL out of bounds", -1,
+ 0 },
+ { PBL_BOUND_ERR_CH1, "ULPTX channel 1 PBL out of bounds", -1,
+ 0 },
+ { PBL_BOUND_ERR_CH0, "ULPTX channel 0 PBL out of bounds", -1,
+ 0 },
+ { 0xfffffff, "ULPTX parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+
+ if (csio_handle_intr_status(hw, ULP_TX_INT_CAUSE, ulptx_intr_info))
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * PM TX interrupt handler.
+ */
+static void csio_pmtx_intr_handler(struct csio_hw *hw)
+{
+ static struct intr_info pmtx_intr_info[] = {
+ { PCMD_LEN_OVFL0, "PMTX channel 0 pcmd too large", -1, 1 },
+ { PCMD_LEN_OVFL1, "PMTX channel 1 pcmd too large", -1, 1 },
+ { PCMD_LEN_OVFL2, "PMTX channel 2 pcmd too large", -1, 1 },
+ { ZERO_C_CMD_ERROR, "PMTX 0-length pcmd", -1, 1 },
+ { 0xffffff0, "PMTX framing error", -1, 1 },
+ { OESPI_PAR_ERROR, "PMTX oespi parity error", -1, 1 },
+ { DB_OPTIONS_PAR_ERROR, "PMTX db_options parity error", -1,
+ 1 },
+ { ICSPI_PAR_ERROR, "PMTX icspi parity error", -1, 1 },
+ { C_PCMD_PAR_ERROR, "PMTX c_pcmd parity error", -1, 1},
+ { 0, NULL, 0, 0 }
+ };
+
+ if (csio_handle_intr_status(hw, PM_TX_INT_CAUSE, pmtx_intr_info))
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * PM RX interrupt handler.
+ */
+static void csio_pmrx_intr_handler(struct csio_hw *hw)
+{
+ static struct intr_info pmrx_intr_info[] = {
+ { ZERO_E_CMD_ERROR, "PMRX 0-length pcmd", -1, 1 },
+ { 0x3ffff0, "PMRX framing error", -1, 1 },
+ { OCSPI_PAR_ERROR, "PMRX ocspi parity error", -1, 1 },
+ { DB_OPTIONS_PAR_ERROR, "PMRX db_options parity error", -1,
+ 1 },
+ { IESPI_PAR_ERROR, "PMRX iespi parity error", -1, 1 },
+ { E_PCMD_PAR_ERROR, "PMRX e_pcmd parity error", -1, 1},
+ { 0, NULL, 0, 0 }
+ };
+
+ if (csio_handle_intr_status(hw, PM_RX_INT_CAUSE, pmrx_intr_info))
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * CPL switch interrupt handler.
+ */
+static void csio_cplsw_intr_handler(struct csio_hw *hw)
+{
+ static struct intr_info cplsw_intr_info[] = {
+ { CIM_OP_MAP_PERR, "CPLSW CIM op_map parity error", -1, 1 },
+ { CIM_OVFL_ERROR, "CPLSW CIM overflow", -1, 1 },
+ { TP_FRAMING_ERROR, "CPLSW TP framing error", -1, 1 },
+ { SGE_FRAMING_ERROR, "CPLSW SGE framing error", -1, 1 },
+ { CIM_FRAMING_ERROR, "CPLSW CIM framing error", -1, 1 },
+ { ZERO_SWITCH_ERROR, "CPLSW no-switch error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+
+ if (csio_handle_intr_status(hw, CPL_INTR_CAUSE, cplsw_intr_info))
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * LE interrupt handler.
+ */
+static void csio_le_intr_handler(struct csio_hw *hw)
+{
+ static struct intr_info le_intr_info[] = {
+ { LIPMISS, "LE LIP miss", -1, 0 },
+ { LIP0, "LE 0 LIP error", -1, 0 },
+ { PARITYERR, "LE parity error", -1, 1 },
+ { UNKNOWNCMD, "LE unknown command", -1, 1 },
+ { REQQPARERR, "LE request queue parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+
+ if (csio_handle_intr_status(hw, LE_DB_INT_CAUSE, le_intr_info))
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * MPS interrupt handler.
+ */
+static void csio_mps_intr_handler(struct csio_hw *hw)
+{
+ static struct intr_info mps_rx_intr_info[] = {
+ { 0xffffff, "MPS Rx parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+ static struct intr_info mps_tx_intr_info[] = {
+ { TPFIFO, "MPS Tx TP FIFO parity error", -1, 1 },
+ { NCSIFIFO, "MPS Tx NC-SI FIFO parity error", -1, 1 },
+ { TXDATAFIFO, "MPS Tx data FIFO parity error", -1, 1 },
+ { TXDESCFIFO, "MPS Tx desc FIFO parity error", -1, 1 },
+ { BUBBLE, "MPS Tx underflow", -1, 1 },
+ { SECNTERR, "MPS Tx SOP/EOP error", -1, 1 },
+ { FRMERR, "MPS Tx framing error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+ static struct intr_info mps_trc_intr_info[] = {
+ { FILTMEM, "MPS TRC filter parity error", -1, 1 },
+ { PKTFIFO, "MPS TRC packet FIFO parity error", -1, 1 },
+ { MISCPERR, "MPS TRC misc parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+ static struct intr_info mps_stat_sram_intr_info[] = {
+ { 0x1fffff, "MPS statistics SRAM parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+ static struct intr_info mps_stat_tx_intr_info[] = {
+ { 0xfffff, "MPS statistics Tx FIFO parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+ static struct intr_info mps_stat_rx_intr_info[] = {
+ { 0xffffff, "MPS statistics Rx FIFO parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+ static struct intr_info mps_cls_intr_info[] = {
+ { MATCHSRAM, "MPS match SRAM parity error", -1, 1 },
+ { MATCHTCAM, "MPS match TCAM parity error", -1, 1 },
+ { HASHSRAM, "MPS hash SRAM parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+
+ int fat;
+
+ fat = csio_handle_intr_status(hw, MPS_RX_PERR_INT_CAUSE,
+ mps_rx_intr_info) +
+ csio_handle_intr_status(hw, MPS_TX_INT_CAUSE,
+ mps_tx_intr_info) +
+ csio_handle_intr_status(hw, MPS_TRC_INT_CAUSE,
+ mps_trc_intr_info) +
+ csio_handle_intr_status(hw, MPS_STAT_PERR_INT_CAUSE_SRAM,
+ mps_stat_sram_intr_info) +
+ csio_handle_intr_status(hw, MPS_STAT_PERR_INT_CAUSE_TX_FIFO,
+ mps_stat_tx_intr_info) +
+ csio_handle_intr_status(hw, MPS_STAT_PERR_INT_CAUSE_RX_FIFO,
+ mps_stat_rx_intr_info) +
+ csio_handle_intr_status(hw, MPS_CLS_INT_CAUSE,
+ mps_cls_intr_info);
+
+ csio_wr_reg32(hw, 0, MPS_INT_CAUSE);
+ csio_rd_reg32(hw, MPS_INT_CAUSE); /* flush */
+ if (fat)
+ csio_hw_fatal_err(hw);
+}
+
+#define MEM_INT_MASK (PERR_INT_CAUSE | ECC_CE_INT_CAUSE | ECC_UE_INT_CAUSE)
+
+/*
+ * EDC/MC interrupt handler.
+ */
+static void csio_mem_intr_handler(struct csio_hw *hw, int idx)
+{
+ static const char name[3][5] = { "EDC0", "EDC1", "MC" };
+
+ unsigned int addr, cnt_addr, v;
+
+ if (idx <= MEM_EDC1) {
+ addr = EDC_REG(EDC_INT_CAUSE, idx);
+ cnt_addr = EDC_REG(EDC_ECC_STATUS, idx);
+ } else {
+ addr = MC_INT_CAUSE;
+ cnt_addr = MC_ECC_STATUS;
+ }
+
+ v = csio_rd_reg32(hw, addr) & MEM_INT_MASK;
+ if (v & PERR_INT_CAUSE)
+ csio_fatal(hw, "%s FIFO parity error\n", name[idx]);
+ if (v & ECC_CE_INT_CAUSE) {
+ uint32_t cnt = ECC_CECNT_GET(csio_rd_reg32(hw, cnt_addr));
+
+ csio_wr_reg32(hw, ECC_CECNT_MASK, cnt_addr);
+ csio_warn(hw, "%u %s correctable ECC data error%s\n",
+ cnt, name[idx], cnt > 1 ? "s" : "");
+ }
+ if (v & ECC_UE_INT_CAUSE)
+ csio_fatal(hw, "%s uncorrectable ECC data error\n", name[idx]);
+
+ csio_wr_reg32(hw, v, addr);
+ if (v & (PERR_INT_CAUSE | ECC_UE_INT_CAUSE))
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * MA interrupt handler.
+ */
+static void csio_ma_intr_handler(struct csio_hw *hw)
+{
+ uint32_t v, status = csio_rd_reg32(hw, MA_INT_CAUSE);
+
+ if (status & MEM_PERR_INT_CAUSE)
+ csio_fatal(hw, "MA parity error, parity status %#x\n",
+ csio_rd_reg32(hw, MA_PARITY_ERROR_STATUS));
+ if (status & MEM_WRAP_INT_CAUSE) {
+ v = csio_rd_reg32(hw, MA_INT_WRAP_STATUS);
+ csio_fatal(hw,
+ "MA address wrap-around error by client %u to address %#x\n",
+ MEM_WRAP_CLIENT_NUM_GET(v), MEM_WRAP_ADDRESS_GET(v) << 4);
+ }
+ csio_wr_reg32(hw, status, MA_INT_CAUSE);
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * SMB interrupt handler.
+ */
+static void csio_smb_intr_handler(struct csio_hw *hw)
+{
+ static struct intr_info smb_intr_info[] = {
+ { MSTTXFIFOPARINT, "SMB master Tx FIFO parity error", -1, 1 },
+ { MSTRXFIFOPARINT, "SMB master Rx FIFO parity error", -1, 1 },
+ { SLVFIFOPARINT, "SMB slave FIFO parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+
+ if (csio_handle_intr_status(hw, SMB_INT_CAUSE, smb_intr_info))
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * NC-SI interrupt handler.
+ */
+static void csio_ncsi_intr_handler(struct csio_hw *hw)
+{
+ static struct intr_info ncsi_intr_info[] = {
+ { CIM_DM_PRTY_ERR, "NC-SI CIM parity error", -1, 1 },
+ { MPS_DM_PRTY_ERR, "NC-SI MPS parity error", -1, 1 },
+ { TXFIFO_PRTY_ERR, "NC-SI Tx FIFO parity error", -1, 1 },
+ { RXFIFO_PRTY_ERR, "NC-SI Rx FIFO parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+
+ if (csio_handle_intr_status(hw, NCSI_INT_CAUSE, ncsi_intr_info))
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * XGMAC interrupt handler.
+ */
+static void csio_xgmac_intr_handler(struct csio_hw *hw, int port)
+{
+ uint32_t v = csio_rd_reg32(hw, PORT_REG(port, XGMAC_PORT_INT_CAUSE));
+
+ v &= TXFIFO_PRTY_ERR | RXFIFO_PRTY_ERR;
+ if (!v)
+ return;
+
+ if (v & TXFIFO_PRTY_ERR)
+ csio_fatal(hw, "XGMAC %d Tx FIFO parity error\n", port);
+ if (v & RXFIFO_PRTY_ERR)
+ csio_fatal(hw, "XGMAC %d Rx FIFO parity error\n", port);
+ csio_wr_reg32(hw, v, PORT_REG(port, XGMAC_PORT_INT_CAUSE));
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * PL interrupt handler.
+ */
+static void csio_pl_intr_handler(struct csio_hw *hw)
+{
+ static struct intr_info pl_intr_info[] = {
+ { FATALPERR, "T4 fatal parity error", -1, 1 },
+ { PERRVFID, "PL VFID_MAP parity error", -1, 1 },
+ { 0, NULL, 0, 0 }
+ };
+
+ if (csio_handle_intr_status(hw, PL_PL_INT_CAUSE, pl_intr_info))
+ csio_hw_fatal_err(hw);
+}
+
+/*
+ * csio_hw_slow_intr_handler - control path interrupt handler
+ * @hw: HW module
+ *
+ * Interrupt handler for non-data global interrupt events, e.g., errors.
+ * The designation 'slow' is because it involves register reads, while
+ * data interrupts typically don't involve any MMIOs.
+ */
+int
+csio_hw_slow_intr_handler(struct csio_hw *hw)
+{
+ uint32_t cause = csio_rd_reg32(hw, PL_INT_CAUSE);
+
+ if (!(cause & CSIO_GLBL_INTR_MASK)) {
+ csio_inc_stats(hw, n_plint_unexp);
+ return 0;
+ }
+
+ csio_dbg(hw, "Slow interrupt! cause: 0x%x\n", cause);
+
+ csio_inc_stats(hw, n_plint_cnt);
+
+ if (cause & CIM)
+ csio_cim_intr_handler(hw);
+
+ if (cause & MPS)
+ csio_mps_intr_handler(hw);
+
+ if (cause & NCSI)
+ csio_ncsi_intr_handler(hw);
+
+ if (cause & PL)
+ csio_pl_intr_handler(hw);
+
+ if (cause & SMB)
+ csio_smb_intr_handler(hw);
+
+ if (cause & XGMAC0)
+ csio_xgmac_intr_handler(hw, 0);
+
+ if (cause & XGMAC1)
+ csio_xgmac_intr_handler(hw, 1);
+
+ if (cause & XGMAC_KR0)
+ csio_xgmac_intr_handler(hw, 2);
+
+ if (cause & XGMAC_KR1)
+ csio_xgmac_intr_handler(hw, 3);
+
+ if (cause & PCIE)
+ csio_pcie_intr_handler(hw);
+
+ if (cause & MC)
+ csio_mem_intr_handler(hw, MEM_MC);
+
+ if (cause & EDC0)
+ csio_mem_intr_handler(hw, MEM_EDC0);
+
+ if (cause & EDC1)
+ csio_mem_intr_handler(hw, MEM_EDC1);
+
+ if (cause & LE)
+ csio_le_intr_handler(hw);
+
+ if (cause & TP)
+ csio_tp_intr_handler(hw);
+
+ if (cause & MA)
+ csio_ma_intr_handler(hw);
+
+ if (cause & PM_TX)
+ csio_pmtx_intr_handler(hw);
+
+ if (cause & PM_RX)
+ csio_pmrx_intr_handler(hw);
+
+ if (cause & ULP_RX)
+ csio_ulprx_intr_handler(hw);
+
+ if (cause & CPL_SWITCH)
+ csio_cplsw_intr_handler(hw);
+
+ if (cause & SGE)
+ csio_sge_intr_handler(hw);
+
+ if (cause & ULP_TX)
+ csio_ulptx_intr_handler(hw);
+
+ /* Clear the interrupts just processed for which we are the master. */
+ csio_wr_reg32(hw, cause & CSIO_GLBL_INTR_MASK, PL_INT_CAUSE);
+ csio_rd_reg32(hw, PL_INT_CAUSE); /* flush */
+
+ return 1;
+}
+
+/*****************************************************************************
+ * HW <--> mailbox interfacing routines.
+ ****************************************************************************/
+/*
+ * csio_mberr_worker - Worker thread (dpc) for mailbox/error completions
+ *
+ * @data: Private data pointer.
+ *
+ * Called from worker thread context.
+ */
+static void
+csio_mberr_worker(void *data)
+{
+ struct csio_hw *hw = (struct csio_hw *)data;
+ struct csio_mbm *mbm = &hw->mbm;
+ LIST_HEAD(cbfn_q);
+ struct csio_mb *mbp_next;
+ csio_retval_t rv;
+
+ del_timer_sync(&mbm->timer);
+
+ spin_lock_irq(&hw->lock);
+ if (list_empty(&mbm->cbfn_q)) {
+ spin_unlock_irq(&hw->lock);
+ return;
+ }
+
+ list_splice_tail_init(&mbm->cbfn_q, &cbfn_q);
+ mbm->stats.n_cbfnq = 0;
+
+ /* Try to start waiting mailboxes */
+ csio_deq_from_head(&mbm->req_q, &mbp_next);
+ if (mbp_next) {
+ rv = csio_mb_issue(hw, mbp_next);
+ if (rv != CSIO_SUCCESS)
+ list_add_tail(&mbp_next->list, &mbm->req_q);
+ else
+ csio_dec_stats(mbm, n_activeq);
+ }
+ spin_unlock_irq(&hw->lock);
+
+ /* Now callback completions */
+ csio_mb_completions(hw, &cbfn_q);
+
+}
+
+/*
+ * csio_hw_mb_timer - Top-level Mailbox timeout handler.
+ *
+ * @data: private data pointer
+ *
+ **/
+static void
+csio_hw_mb_timer(uintptr_t data)
+{
+ struct csio_hw *hw = (struct csio_hw *)data;
+ struct csio_mb *mbp = NULL;
+
+ spin_lock_irq(&hw->lock);
+ mbp = csio_mb_tmo_handler(hw);
+ spin_unlock_irq(&hw->lock);
+
+ /* Call back the function for the timed-out Mailbox */
+ if (mbp)
+ mbp->mb_cbfn(hw, mbp);
+
+}
+
+/*
+ * csio_hw_mbm_cleanup - Cleanup Mailbox module.
+ * @hw: HW module
+ *
+ * Called with lock held, should exit with lock held.
+ * Cancels outstanding mailboxes (waiting, in-flight) and gathers them
+ * into a local queue. Drops lock and calls the completions. Holds
+ * lock and returns.
+ */
+static void
+csio_hw_mbm_cleanup(struct csio_hw *hw)
+{
+ LIST_HEAD(cbfn_q);
+
+ csio_mb_cancel_all(hw, &cbfn_q);
+
+ spin_unlock_irq(&hw->lock);
+ csio_mb_completions(hw, &cbfn_q);
+ spin_lock_irq(&hw->lock);
+}
+
+/*****************************************************************************
+ * Event handling
+ ****************************************************************************/
+csio_retval_t
+csio_enqueue_evt(struct csio_hw *hw, enum csio_evt type, void *evt_msg,
+ uint16_t len)
+{
+ struct csio_evt_msg *evt_entry = NULL;
+
+ if (type >= CSIO_EVT_MAX)
+ return CSIO_INVAL;
+
+ if (len > CSIO_EVT_MSG_SIZE)
+ return CSIO_INVAL;
+
+ if (hw->flags & CSIO_HWF_FWEVT_STOP)
+ return CSIO_INVAL;
+
+ csio_deq_from_head(&hw->evt_free_q, &evt_entry);
+ if (!evt_entry) {
+ csio_err(hw, "Failed to alloc evt entry, msg type %d len %d\n",
+ type, len);
+ return CSIO_NOMEM;
+ }
+
+ /* copy event msg and queue the event */
+ evt_entry->type = type;
+ memcpy((void *)evt_entry->data, evt_msg, len);
+ list_add_tail(&evt_entry->list, &hw->evt_active_q);
+
+ csio_dec_stats(hw, n_evt_freeq);
+ csio_inc_stats(hw, n_evt_activeq);
+
+ return CSIO_SUCCESS;
+}
+
+static csio_retval_t
+csio_enqueue_evt_lock(struct csio_hw *hw, enum csio_evt type, void *evt_msg,
+ uint16_t len, bool msg_sg)
+{
+ struct csio_evt_msg *evt_entry = NULL;
+ struct csio_fl_dma_buf *fl_sg;
+ uint32_t off = 0;
+ unsigned long flags;
+ int n;
+
+ if (type >= CSIO_EVT_MAX)
+ return CSIO_INVAL;
+
+ if (len > CSIO_EVT_MSG_SIZE)
+ return CSIO_INVAL;
+
+ spin_lock_irqsave(&hw->lock, flags);
+ if (hw->flags & CSIO_HWF_FWEVT_STOP) {
+ spin_unlock_irqrestore(&hw->lock, flags);
+ return CSIO_INVAL;
+ }
+ csio_deq_from_head(&hw->evt_free_q, &evt_entry);
+ if (!evt_entry) {
+ csio_err(hw, "Failed to alloc evt entry, msg type %d len %d\n",
+ type, len);
+ spin_unlock_irqrestore(&hw->lock, flags);
+ return CSIO_NOMEM;
+ }
+
+ /* copy event msg and queue the event */
+ evt_entry->type = type;
+
+ /* If Payload in SG list*/
+ if (msg_sg) {
+ fl_sg = (struct csio_fl_dma_buf *) evt_msg;
+ for (n = 0; (n < CSIO_MAX_FLBUF_PER_IQWR && off < len); n++) {
+ memcpy((void *)((uintptr_t)evt_entry->data + off),
+ fl_sg->flbufs[n].vaddr,
+ fl_sg->flbufs[n].len);
+ off += fl_sg->flbufs[n].len;
+ }
+ } else
+ memcpy((void *)evt_entry->data, evt_msg, len);
+
+ list_add_tail(&evt_entry->list, &hw->evt_active_q);
+ spin_unlock_irqrestore(&hw->lock, flags);
+
+ csio_dec_stats(hw, n_evt_freeq);
+ csio_inc_stats(hw, n_evt_activeq);
+
+ return CSIO_SUCCESS;
+}
+
+static void
+csio_free_evt(struct csio_hw *hw, struct csio_evt_msg *evt_entry)
+{
+ if (evt_entry) {
+ spin_lock_irq(&hw->lock);
+ list_del_init(&evt_entry->list);
+ list_add_tail(&evt_entry->list, &hw->evt_free_q);
+ csio_dec_stats(hw, n_evt_activeq);
+ csio_inc_stats(hw, n_evt_freeq);
+ spin_unlock_irq(&hw->lock);
+ }
+}
+
+void
+csio_evtq_flush(struct csio_hw *hw)
+{
+ uint32_t count;
+ count = 30;
+ while (hw->flags & CSIO_HWF_FWEVT_PENDING && count--) {
+ spin_unlock_irq(&hw->lock);
+ msleep(2000);
+ spin_lock_irq(&hw->lock);
+ }
+
+ CSIO_DB_ASSERT(!(hw->flags & CSIO_HWF_FWEVT_PENDING));
+}
+
+static void
+csio_evtq_stop(struct csio_hw *hw)
+{
+ hw->flags |= CSIO_HWF_FWEVT_STOP;
+}
+
+static void
+csio_evtq_start(struct csio_hw *hw)
+{
+ hw->flags &= ~CSIO_HWF_FWEVT_STOP;
+}
+
+static void
+csio_evtq_cleanup(struct csio_hw *hw)
+{
+ struct list_head *evt_entry, *next_entry;
+
+ /* Release outstanding events from activeq to freeq*/
+ if (!list_empty(&hw->evt_active_q))
+ list_splice_tail_init(&hw->evt_active_q, &hw->evt_free_q);
+
+ hw->stats.n_evt_activeq = 0;
+ hw->flags &= ~CSIO_HWF_FWEVT_PENDING;
+
+ /* Freeup event entry */
+ list_for_each_safe(evt_entry, next_entry, &hw->evt_free_q) {
+ kfree(evt_entry);
+ csio_dec_stats(hw, n_evt_freeq);
+ }
+
+ hw->stats.n_evt_freeq = 0;
+}
+
+
+static void
+csio_process_fwevtq_entry(struct csio_hw *hw, void *wr, uint32_t len,
+ struct csio_fl_dma_buf *flb, void *priv)
+{
+ __u8 op;
+ __be64 *data;
+ void *msg = NULL;
+ uint32_t msg_len = 0;
+ bool msg_sg = 0;
+
+ op = ((struct rss_header *) wr)->opcode;
+ if (op == CPL_FW6_PLD) {
+ csio_inc_stats(hw, n_cpl_fw6_pld);
+ if (!flb || !flb->totlen) {
+ csio_inc_stats(hw, n_cpl_unexp);
+ return;
+ }
+
+ msg = (void *) flb;
+ msg_len = flb->totlen;
+ msg_sg = 1;
+
+ data = (__be64 *) msg;
+ } else if (op == CPL_FW6_MSG || op == CPL_FW4_MSG) {
+
+ csio_inc_stats(hw, n_cpl_fw6_msg);
+ /* skip RSS header */
+ msg = (void *)((uintptr_t)wr + sizeof(__be64));
+ msg_len = (op == CPL_FW6_MSG) ? sizeof(struct cpl_fw6_msg) :
+ sizeof(struct cpl_fw4_msg);
+
+ data = (__be64 *) msg;
+ } else {
+ csio_warn(hw, "unexpected CPL %#x on FW event queue\n", op);
+ csio_inc_stats(hw, n_cpl_unexp);
+ return;
+ }
+
+ /*
+ * Enqueue event to EventQ. Events processing happens
+ * in Event worker thread context
+ */
+ if (csio_enqueue_evt_lock(hw, CSIO_EVT_FW, msg,
+ (uint16_t)msg_len, msg_sg))
+ csio_inc_stats(hw, n_evt_drop);
+}
+
+void
+csio_evtq_worker(struct work_struct *work)
+{
+ struct csio_hw *hw = container_of(work, struct csio_hw, evtq_work);
+ struct list_head *evt_entry, *next_entry;
+ LIST_HEAD(evt_q);
+ struct csio_evt_msg *evt_msg;
+ struct cpl_fw6_msg *msg;
+ struct csio_rnode *rn;
+ csio_retval_t rv = 0;
+ uint8_t evtq_stop = 0;
+
+ csio_dbg(hw, "event worker thread active evts#%d\n",
+ hw->stats.n_evt_activeq);
+
+ spin_lock_irq(&hw->lock);
+ while (!list_empty(&hw->evt_active_q)) {
+ list_splice_tail_init(&hw->evt_active_q, &evt_q);
+ spin_unlock_irq(&hw->lock);
+
+ list_for_each_safe(evt_entry, next_entry, &evt_q) {
+ evt_msg = (struct csio_evt_msg *) evt_entry;
+
+ /* Drop events if queue is STOPPED */
+ spin_lock_irq(&hw->lock);
+ if (hw->flags & CSIO_HWF_FWEVT_STOP)
+ evtq_stop = 1;
+ spin_unlock_irq(&hw->lock);
+ if (evtq_stop) {
+ csio_inc_stats(hw, n_evt_drop);
+ goto free_evt;
+ }
+
+ switch (evt_msg->type) {
+
+ case CSIO_EVT_FW:
+ msg = (struct cpl_fw6_msg *)(evt_msg->data);
+
+ if ((msg->opcode == CPL_FW6_MSG ||
+ msg->opcode == CPL_FW4_MSG) &&
+ !msg->type) {
+ rv = csio_mb_fwevt_handler(hw,
+ msg->data);
+ if (!rv)
+ break;
+ /* Handle any remaining fw events */
+ csio_fcoe_fwevt_handler(hw,
+ msg->opcode, msg->data);
+ } else if (msg->opcode == CPL_FW6_PLD) {
+
+ csio_fcoe_fwevt_handler(hw,
+ msg->opcode, msg->data);
+ } else {
+ csio_warn(hw,
+ "Unhandled FW msg op %x type %x\n",
+ msg->opcode, msg->type);
+ csio_inc_stats(hw, n_evt_drop);
+ }
+ break;
+
+ case CSIO_EVT_MBX:
+ csio_mberr_worker(hw);
+ break;
+
+ case CSIO_EVT_DEV_LOSS:
+ memcpy(&rn, evt_msg->data, sizeof(rn));
+ csio_rnode_devloss_handler(rn);
+ break;
+
+ default:
+ csio_warn(hw, "Unhandled event %x on evtq\n",
+ evt_msg->type);
+ csio_inc_stats(hw, n_evt_unexp);
+ break;
+ }
+free_evt:
+ csio_free_evt(hw, evt_msg);
+ }
+
+ spin_lock_irq(&hw->lock);
+ }
+ hw->flags &= ~CSIO_HWF_FWEVT_PENDING;
+ spin_unlock_irq(&hw->lock);
+}
+
+csio_retval_t
+csio_fwevtq_handler(struct csio_hw *hw)
+{
+ csio_retval_t rv;
+
+ if (csio_q_iqid(hw, hw->fwevt_iq_idx) == CSIO_MAX_QID) {
+ csio_inc_stats(hw, n_int_stray);
+ return CSIO_INVAL;
+ }
+
+ rv = csio_wr_process_iq_idx(hw, hw->fwevt_iq_idx,
+ csio_process_fwevtq_entry, NULL);
+ return rv;
+}
+
+/****************************************************************************
+ * Entry points
+ ****************************************************************************/
+
+/* Management module */
+/*
+ * csio_mgmt_req_lookup - Lookup the given IO req exist in Active Q.
+ * mgmt - mgmt module
+ * @io_req - io request
+ *
+ * Return - CSIO_SUCCESS:if given IO Req exists in active Q.
+ * CSIO_INVAL :if lookup fails.
+ */
+csio_retval_t
+csio_mgmt_req_lookup(struct csio_mgmtm *mgmtm, struct csio_ioreq *io_req)
+{
+ struct list_head *tmp;
+
+ /* Lookup ioreq in the ACTIVEQ */
+ list_for_each(tmp, &mgmtm->active_q) {
+ if (io_req == (struct csio_ioreq *)tmp)
+ return CSIO_SUCCESS;
+ }
+ return CSIO_INVAL;
+}
+
+/*
+ * csio_mgmts_tmo_handler - MGMT IO Timeout handler.
+ * @data - Event data.
+ *
+ * Return - none.
+ */
+static void
+csio_mgmt_tmo_handler(uintptr_t data)
+{
+ struct csio_mgmtm *mgmtm = (struct csio_mgmtm *) data;
+ struct list_head *tmp;
+ struct csio_ioreq *io_req;
+
+ csio_dbg(mgmtm->hw, "Mgmt timer invoked!\n");
+
+ spin_lock_irq(&mgmtm->hw->lock);
+
+ list_for_each(tmp, &mgmtm->active_q) {
+ io_req = (struct csio_ioreq *) tmp;
+ io_req->tmo -= min_t(uint32_t, io_req->tmo, ECM_MIN_TMO);
+
+ if (!io_req->tmo) {
+ /* Dequeue the request from retry Q. */
+ tmp = csio_list_prev(tmp);
+ list_del_init(&io_req->sm.sm_list);
+ if (io_req->io_cbfn) {
+ /* io_req will be freed by completion handler */
+ io_req->wr_status = CSIO_TIMEOUT;
+ io_req->io_cbfn(mgmtm->hw, io_req);
+ } else {
+ CSIO_DB_ASSERT(0);
+ }
+ }
+ }
+
+ /* If retry queue is not empty, re-arm timer */
+ if (!list_empty(&mgmtm->active_q))
+ mod_timer(&mgmtm->mgmt_timer,
+ jiffies + msecs_to_jiffies(ECM_MIN_TMO));
+ spin_unlock_irq(&mgmtm->hw->lock);
+}
+
+static void
+csio_mgmtm_cleanup(struct csio_mgmtm *mgmtm)
+{
+ struct csio_hw *hw = mgmtm->hw;
+ struct csio_ioreq *io_req;
+ struct list_head *tmp;
+ uint32_t count;
+
+ count = 30;
+ /* Wait for all outstanding req to complete gracefully */
+ while ((!list_empty(&mgmtm->active_q)) && count--) {
+ spin_unlock_irq(&hw->lock);
+ msleep(2000);
+ spin_lock_irq(&hw->lock);
+ }
+
+ /* release outstanding req from ACTIVEQ */
+ list_for_each(tmp, &mgmtm->active_q) {
+ io_req = (struct csio_ioreq *) tmp;
+ tmp = csio_list_prev(tmp);
+ list_del_init(&io_req->sm.sm_list);
+ mgmtm->stats.n_active--;
+ if (io_req->io_cbfn) {
+ /* io_req will be freed by completion handler */
+ io_req->wr_status = CSIO_TIMEOUT;
+ io_req->io_cbfn(mgmtm->hw, io_req);
+ }
+ }
+}
+
+/*
+ * csio_mgmt_init - Mgmt module init entry point
+ * @mgmtsm - mgmt module
+ * @hw - HW module
+ *
+ * Initialize mgmt timer, resource wait queue, active queue,
+ * completion q. Allocate Egress and Ingress
+ * WR queues and save off the queue index returned by the WR
+ * module for future use. Allocate and save off mgmt reqs in the
+ * mgmt_req_freelist for future use. Make sure their SM is initialized
+ * to uninit state.
+ * Returns: CSIO_SUCCESS - on success
+ * CSIO_NOMEM - on error.
+ */
+static csio_retval_t
+csio_mgmtm_init(struct csio_mgmtm *mgmtm, struct csio_hw *hw)
+{
+ struct timer_list *timer = &mgmtm->mgmt_timer;
+
+ init_timer(timer);
+ timer->function = csio_mgmt_tmo_handler;
+ timer->data = (unsigned long)mgmtm;
+
+ INIT_LIST_HEAD(&mgmtm->active_q);
+ INIT_LIST_HEAD(&mgmtm->cbfn_q);
+
+ mgmtm->hw = hw;
+ /*mgmtm->iq_idx = hw->fwevt_iq_idx;*/
+
+ return CSIO_SUCCESS;
+}
+
+/*
+ * csio_mgmtm_exit - MGMT module exit entry point
+ * @mgmtsm - mgmt module
+ *
+ * This function called during MGMT module uninit.
+ * Stop timers, free ioreqs allocated.
+ * Returns: None
+ *
+ */
+static void
+csio_mgmtm_exit(struct csio_mgmtm *mgmtm)
+{
+ del_timer_sync(&mgmtm->mgmt_timer);
+}
+
+
+/**
+ * csio_hw_start - Kicks off the HW State machine
+ * @hw: Pointer to HW module.
+ *
+ * It is assumed that the initialization is a synchronous operation.
+ * So when we return afer posting the event, the HW SM should be in
+ * the ready state, if there were no errors during init.
+ */
+csio_retval_t
+csio_hw_start(struct csio_hw *hw)
+{
+ spin_lock_irq(&hw->lock);
+ csio_post_event(&hw->sm, CSIO_HWE_CFG);
+ spin_unlock_irq(&hw->lock);
+
+ if (csio_is_hw_ready(hw))
+ return CSIO_SUCCESS;
+ else
+ return CSIO_INVAL;
+}
+
+csio_retval_t
+csio_hw_stop(struct csio_hw *hw)
+{
+ csio_post_event(&hw->sm, CSIO_HWE_PCI_REMOVE);
+
+ if (csio_is_hw_removing(hw))
+ return CSIO_SUCCESS;
+ else
+ return CSIO_INVAL;
+}
+
+/* Max reset retries */
+#define CSIO_MAX_RESET_RETRIES 3
+
+/**
+ * csio_hw_reset - Reset the hardware
+ * @hw: HW module.
+ *
+ * Caller should hold lock across this function.
+ */
+csio_retval_t
+csio_hw_reset(struct csio_hw *hw)
+{
+ if (!csio_is_hw_master(hw))
+ return CSIO_NOPERM;
+
+ if (hw->rst_retries >= CSIO_MAX_RESET_RETRIES) {
+ csio_dbg(hw, "Max hw reset attempts reached..");
+ return CSIO_INVAL;
+ }
+
+ hw->rst_retries++;
+ csio_post_event(&hw->sm, CSIO_HWE_HBA_RESET);
+
+ if (csio_is_hw_ready(hw)) {
+ hw->rst_retries = 0;
+ hw->stats.n_reset_start = jiffies_to_msecs(jiffies);
+ return CSIO_SUCCESS;
+ } else
+ return CSIO_INVAL;
+}
+
+/*
+ * csio_hw_get_device_id - Caches the Adapter's vendor & device id.
+ * @hw: HW module.
+ */
+static void
+csio_hw_get_device_id(struct csio_hw *hw)
+{
+ /* Is the adapter device id cached already ?*/
+ if (csio_is_dev_id_cached(hw))
+ return;
+
+ /* Get the PCI vendor & device id */
+ pci_read_config_word(hw->pdev, PCI_VENDOR_ID,
+ &hw->params.pci.vendor_id);
+ pci_read_config_word(hw->pdev, PCI_DEVICE_ID,
+ &hw->params.pci.device_id);
+
+ csio_dev_id_cached(hw);
+
+} /* csio_hw_get_device_id */
+
+/*
+ * csio_hw_set_description - Set the model, description of the hw.
+ * @hw: HW module.
+ * @ven_id: PCI Vendor ID
+ * @dev_id: PCI Device ID
+ */
+static void
+csio_hw_set_description(struct csio_hw *hw, uint16_t ven_id, uint16_t dev_id)
+{
+ uint32_t adap_type, prot_type;
+
+ if (ven_id == CSIO_VENDOR_ID) {
+ prot_type = (dev_id & CSIO_ASIC_DEVID_PROTO_MASK);
+ adap_type = (dev_id & CSIO_ASIC_DEVID_TYPE_MASK);
+
+ if (prot_type == CSIO_FPGA) {
+ memcpy(hw->model_desc,
+ csio_fcoe_adapters[13].description, 32);
+ } else if (prot_type == CSIO_T4_FCOE_ASIC) {
+ memcpy(hw->hw_ver,
+ csio_fcoe_adapters[adap_type].model_no, 16);
+ memcpy(hw->model_desc,
+ csio_fcoe_adapters[adap_type].description, 32);
+ } else {
+ char tempName[32] = "Chelsio FCoE Controller";
+ memcpy(hw->model_desc, tempName, 32);
+
+ CSIO_DB_ASSERT(0);
+ }
+ }
+} /* csio_hw_set_description */
+
+/**
+ * csio_hw_init - Initialize HW module.
+ * @hw: Pointer to HW module.
+ *
+ * Initialize the members of the HW module.
+ */
+csio_retval_t
+csio_hw_init(struct csio_hw *hw)
+{
+ csio_retval_t rv = CSIO_INVAL;
+ uint32_t i;
+ uint16_t ven_id, dev_id;
+ struct csio_evt_msg *evt_entry;
+
+ INIT_LIST_HEAD(&hw->sm.sm_list);
+ csio_init_state(&hw->sm, csio_hws_uninit);
+ spin_lock_init(&hw->lock);
+ INIT_LIST_HEAD(&hw->sln_head);
+
+ /* Get the PCI vendor & device id */
+ csio_hw_get_device_id(hw);
+
+ strcpy(hw->name, CSIO_HW_NAME);
+
+ /* Set the model & its description */
+
+ ven_id = hw->params.pci.vendor_id;
+ dev_id = hw->params.pci.device_id;
+
+ csio_hw_set_description(hw, ven_id, dev_id);
+
+ /* Initialize default log level */
+ hw->params.log_level = (uint32_t) csio_dbg_level;
+
+ csio_set_fwevt_intr_idx(hw, -1);
+ csio_set_nondata_intr_idx(hw, -1);
+
+ /* Init all the modules: Mailbox, WorkRequest and Transport */
+ if (csio_mbm_init(csio_hw_to_mbm(hw), hw, csio_hw_mb_timer))
+ goto err;
+
+ rv = csio_wrm_init(csio_hw_to_wrm(hw), hw);
+ if (rv)
+ goto err_mbm_exit;
+
+ rv = csio_scsim_init(csio_hw_to_scsim(hw), hw);
+ if (rv)
+ goto err_wrm_exit;
+
+ rv = csio_mgmtm_init(csio_hw_to_mgmtm(hw), hw);
+ if (rv)
+ goto err_scsim_exit;
+ /* Pre-allocate evtq and initialize them */
+ INIT_LIST_HEAD(&hw->evt_active_q);
+ INIT_LIST_HEAD(&hw->evt_free_q);
+ for (i = 0; i < csio_evtq_sz; i++) {
+
+ evt_entry = kzalloc(sizeof(struct csio_evt_msg), GFP_KERNEL);
+ if (!evt_entry) {
+ csio_err(hw, "Failed to initialize eventq");
+ goto err_evtq_cleanup;
+ }
+
+ list_add_tail(&evt_entry->list, &hw->evt_free_q);
+ csio_inc_stats(hw, n_evt_freeq);
+ }
+
+ hw->dev_num = dev_num;
+ dev_num++;
+
+ return CSIO_SUCCESS;
+
+err_evtq_cleanup:
+ csio_evtq_cleanup(hw);
+ csio_mgmtm_exit(csio_hw_to_mgmtm(hw));
+err_scsim_exit:
+ csio_scsim_exit(csio_hw_to_scsim(hw));
+err_wrm_exit:
+ csio_wrm_exit(csio_hw_to_wrm(hw), hw);
+err_mbm_exit:
+ csio_mbm_exit(csio_hw_to_mbm(hw));
+err:
+ return rv;
+}
+
+/**
+ * csio_hw_exit - Un-initialize HW module.
+ * @hw: Pointer to HW module.
+ *
+ */
+void
+csio_hw_exit(struct csio_hw *hw)
+{
+ csio_evtq_cleanup(hw);
+ csio_mgmtm_exit(csio_hw_to_mgmtm(hw));
+ csio_scsim_exit(csio_hw_to_scsim(hw));
+ csio_wrm_exit(csio_hw_to_wrm(hw), hw);
+ csio_mbm_exit(csio_hw_to_mbm(hw));
+}
This patch contains the hardware interfacing functionality (chip/firmware initialization/setup) and error handling. It also has slow path event handling functionality, the Makefile and Kconfig changes. Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com> --- drivers/scsi/Kconfig | 1 + drivers/scsi/Makefile | 1 + drivers/scsi/csiostor/Kconfig | 20 + drivers/scsi/csiostor/Makefile | 11 + drivers/scsi/csiostor/csio_hw.c | 4385 +++++++++++++++++++++++++++++++++++++++ 5 files changed, 4418 insertions(+), 0 deletions(-) create mode 100644 drivers/scsi/csiostor/Kconfig create mode 100644 drivers/scsi/csiostor/Makefile create mode 100644 drivers/scsi/csiostor/csio_hw.c