| Message ID | 1345132911-29680-1-git-send-email-andreas.devel@googlemail.com |
|---|---|
| State | Accepted, archived |
| Commit | bfc325ed38c40c1ecd7f7074720356e464870b0d |
| Delegated to: | Andreas Bießmann |
| Headers | show |
On 8/17/2012 0:01, Andreas Bießmann wrote: > A lot of at91 boards have the console_init_f in board_init. This is useless > cause it was called before by generic code in lib/board.c. > > Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> > cc: Jens Scharsig <esw@bus-elektronik.de> > cc: Stelian Pop <stelian@popies.net> > cc: Sedji Gaouaou<sedji.gaouaou@atmel.com> > cc: Albin Tonnerre <albin.tonnerre@free-electrons.com> > cc: Eric Benard <eric@eukrea.com> > --- > board/BuS/eb_cpux9k2/cpux9k2.c | 2 -- > board/BuS/vl_ma2sc/vl_ma2sc.c | 3 --- > board/atmel/at91sam9261ek/at91sam9261ek.c | 3 --- > board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 3 --- > board/atmel/at91sam9rlek/at91sam9rlek.c | 3 --- > board/calao/sbc35_a9g20/sbc35_a9g20.c | 3 --- > board/calao/tny_a9260/tny_a9260.c | 3 --- > board/eukrea/cpuat91/cpuat91.c | 2 -- > 8 files changed, 22 deletions(-) > > diff --git a/board/BuS/eb_cpux9k2/cpux9k2.c b/board/BuS/eb_cpux9k2/cpux9k2.c > index 54f9b64..776226f 100644 > --- a/board/BuS/eb_cpux9k2/cpux9k2.c > +++ b/board/BuS/eb_cpux9k2/cpux9k2.c > @@ -59,8 +59,6 @@ DECLARE_GLOBAL_DATA_PTR; > int board_init(void) > { > at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; > - /* Enable Ctrlc */ > - console_init_f(); > > /* Correct IRDA resistor problem / Set PA23_TXD in Output */ > writel(ATMEL_PMX_AA_TXD2, &pio->pioa.oer); > diff --git a/board/BuS/vl_ma2sc/vl_ma2sc.c b/board/BuS/vl_ma2sc/vl_ma2sc.c > index 62ed6fb..84b2060 100644 > --- a/board/BuS/vl_ma2sc/vl_ma2sc.c > +++ b/board/BuS/vl_ma2sc/vl_ma2sc.c > @@ -244,9 +244,6 @@ int board_init(void) > writel(pin, &pio->piod.odr); > writel(pin, &pio->piod.owdr); > > - /* Enable Ctrlc */ > - console_init_f(); > - > gd->bd->bi_arch_number = MACH_TYPE_VL_MA2SC; > /* adress of boot parameters */ > gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; > diff --git a/board/atmel/at91sam9261ek/at91sam9261ek.c b/board/atmel/at91sam9261ek/at91sam9261ek.c > index 47ab839..d30a1ee 100644 > --- a/board/atmel/at91sam9261ek/at91sam9261ek.c > +++ b/board/atmel/at91sam9261ek/at91sam9261ek.c > @@ -242,9 +242,6 @@ void lcd_show_board_info(void) > > int board_init(void) > { > - /* Enable Ctrlc */ > - console_init_f(); > - Tested on at91sam9g10ek board. It works well without this. > #ifdef CONFIG_AT91SAM9G10EK > /* arch number of AT91SAM9G10EK-Board */ > gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G10EK; > diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c > index 5a04274..d02312c 100644 > --- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c > +++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c > @@ -258,9 +258,6 @@ int board_early_init_f(void) > > int board_init(void) > { > - /* Enable Ctrlc */ > - console_init_f(); > - Tested on at91sam9m10g45ek board. It works well without this. > /* arch number of AT91SAM9M10G45EK-Board */ > #ifdef CONFIG_AT91SAM9M10G45EK > gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9M10G45EK; > diff --git a/board/atmel/at91sam9rlek/at91sam9rlek.c b/board/atmel/at91sam9rlek/at91sam9rlek.c > index ef0ddd7..e92ec6e 100644 > --- a/board/atmel/at91sam9rlek/at91sam9rlek.c > +++ b/board/atmel/at91sam9rlek/at91sam9rlek.c > @@ -192,9 +192,6 @@ int board_early_init_f(void) > > int board_init(void) > { > - /* Enable Ctrlc */ > - console_init_f(); > - > /* arch number of AT91SAM9RLEK-Board */ > gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9RLEK; > /* adress of boot parameters */ > diff --git a/board/calao/sbc35_a9g20/sbc35_a9g20.c b/board/calao/sbc35_a9g20/sbc35_a9g20.c > index b6c8791..d3b3684 100644 > --- a/board/calao/sbc35_a9g20/sbc35_a9g20.c > +++ b/board/calao/sbc35_a9g20/sbc35_a9g20.c > @@ -149,9 +149,6 @@ static void sbc35_a9g20_macb_hw_init(void) > > int board_init(void) > { > - /* Enable Ctrlc */ > - console_init_f(); > - > /* adress of boot parameters */ > gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; > > diff --git a/board/calao/tny_a9260/tny_a9260.c b/board/calao/tny_a9260/tny_a9260.c > index 31074d0..86e7e65 100644 > --- a/board/calao/tny_a9260/tny_a9260.c > +++ b/board/calao/tny_a9260/tny_a9260.c > @@ -83,9 +83,6 @@ static void tny_a9260_nand_hw_init(void) > > int board_init(void) > { > - /* Enable Ctrlc */ > - console_init_f(); > - > /* adress of boot parameters */ > gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; > > diff --git a/board/eukrea/cpuat91/cpuat91.c b/board/eukrea/cpuat91/cpuat91.c > index f654f87..c74c3fc 100644 > --- a/board/eukrea/cpuat91/cpuat91.c > +++ b/board/eukrea/cpuat91/cpuat91.c > @@ -43,8 +43,6 @@ DECLARE_GLOBAL_DATA_PTR; > > int board_init(void) > { > - /* Enable Ctrlc */ > - console_init_f(); > /* arch number of CPUAT91-Board */ > gd->bd->bi_arch_number = MACH_TYPE_CPUAT91; > /* adress of boot parameters */ >
Dear Bo Shen, Am Dienstag, 21. August 2012 schrieb Bo Shen : > On 8/17/2012 0:01, Andreas Bießmann wrote: > >> A lot of at91 boards have the console_init_f in board_init. This is >> useless >> cause it was called before by generic code in lib/board.c. >> >> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> >> cc: Jens Scharsig <esw@bus-elektronik.de> >> cc: Stelian Pop <stelian@popies.net> >> cc: Sedji Gaouaou<sedji.gaouaou@atmel.com> >> cc: Albin Tonnerre <albin.tonnerre@free-electrons.com> >> cc: Eric Benard <eric@eukrea.com> >> --- >> board/BuS/eb_cpux9k2/cpux9k2.c | 2 -- >> board/BuS/vl_ma2sc/vl_ma2sc.c | 3 --- >> board/atmel/at91sam9261ek/**at91sam9261ek.c | 3 --- >> board/atmel/at91sam9m10g45ek/**at91sam9m10g45ek.c | 3 --- >> board/atmel/at91sam9rlek/**at91sam9rlek.c | 3 --- >> board/calao/sbc35_a9g20/sbc35_**a9g20.c | 3 --- >> board/calao/tny_a9260/tny_**a9260.c | 3 --- >> board/eukrea/cpuat91/cpuat91.c | 2 -- >> 8 files changed, 22 deletions(-) >> >> diff --git a/board/BuS/eb_cpux9k2/**cpux9k2.c b/board/BuS/eb_cpux9k2/** >> cpux9k2.c >> index 54f9b64..776226f 100644 >> --- a/board/BuS/eb_cpux9k2/**cpux9k2.c >> +++ b/board/BuS/eb_cpux9k2/**cpux9k2.c >> @@ -59,8 +59,6 @@ DECLARE_GLOBAL_DATA_PTR; >> int board_init(void) >> { >> at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; >> - /* Enable Ctrlc */ >> - console_init_f(); >> >> /* Correct IRDA resistor problem / Set PA23_TXD in Output */ >> writel(ATMEL_PMX_AA_TXD2, &pio->pioa.oer); >> diff --git a/board/BuS/vl_ma2sc/vl_ma2sc.**c >> b/board/BuS/vl_ma2sc/vl_ma2sc.**c >> index 62ed6fb..84b2060 100644 >> --- a/board/BuS/vl_ma2sc/vl_ma2sc.**c >> +++ b/board/BuS/vl_ma2sc/vl_ma2sc.**c >> @@ -244,9 +244,6 @@ int board_init(void) >> writel(pin, &pio->piod.odr); >> writel(pin, &pio->piod.owdr); >> >> - /* Enable Ctrlc */ >> - console_init_f(); >> - >> gd->bd->bi_arch_number = MACH_TYPE_VL_MA2SC; >> /* adress of boot parameters */ >> gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; >> diff --git a/board/atmel/at91sam9261ek/**at91sam9261ek.c >> b/board/atmel/at91sam9261ek/**at91sam9261ek.c >> index 47ab839..d30a1ee 100644 >> --- a/board/atmel/at91sam9261ek/**at91sam9261ek.c >> +++ b/board/atmel/at91sam9261ek/**at91sam9261ek.c >> @@ -242,9 +242,6 @@ void lcd_show_board_info(void) >> >> int board_init(void) >> { >> - /* Enable Ctrlc */ >> - console_init_f(); >> - >> > > Tested on at91sam9g10ek board. It works well without this. > > FYI: If you had used the well known git 'tag' Tested-by this would be added automagically to patchworks patch. Please read http://www.denx.de/wiki/view/U-Boot/Patches#Review_Process_Git_Tags However, thanks for your test report. Best regards Andreas Bießmann >
Hi Andreas, On 8/17/2012 0:01, Andreas Bießmann wrote: > A lot of at91 boards have the console_init_f in board_init. This is useless > cause it was called before by generic code in lib/board.c. > > Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> > cc: Jens Scharsig <esw@bus-elektronik.de> > cc: Stelian Pop <stelian@popies.net> > cc: Sedji Gaouaou<sedji.gaouaou@atmel.com> > cc: Albin Tonnerre <albin.tonnerre@free-electrons.com> > cc: Eric Benard <eric@eukrea.com> > --- > board/BuS/eb_cpux9k2/cpux9k2.c | 2 -- > board/BuS/vl_ma2sc/vl_ma2sc.c | 3 --- > board/atmel/at91sam9261ek/at91sam9261ek.c | 3 --- > board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 3 --- > board/atmel/at91sam9rlek/at91sam9rlek.c | 3 --- > board/calao/sbc35_a9g20/sbc35_a9g20.c | 3 --- > board/calao/tny_a9260/tny_a9260.c | 3 --- > board/eukrea/cpuat91/cpuat91.c | 2 -- > 8 files changed, 22 deletions(-) > > diff --git a/board/BuS/eb_cpux9k2/cpux9k2.c b/board/BuS/eb_cpux9k2/cpux9k2.c > index 54f9b64..776226f 100644 > --- a/board/BuS/eb_cpux9k2/cpux9k2.c > +++ b/board/BuS/eb_cpux9k2/cpux9k2.c > @@ -59,8 +59,6 @@ DECLARE_GLOBAL_DATA_PTR; > int board_init(void) > { > at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; > - /* Enable Ctrlc */ > - console_init_f(); > > /* Correct IRDA resistor problem / Set PA23_TXD in Output */ > writel(ATMEL_PMX_AA_TXD2, &pio->pioa.oer); > diff --git a/board/BuS/vl_ma2sc/vl_ma2sc.c b/board/BuS/vl_ma2sc/vl_ma2sc.c > index 62ed6fb..84b2060 100644 > --- a/board/BuS/vl_ma2sc/vl_ma2sc.c > +++ b/board/BuS/vl_ma2sc/vl_ma2sc.c > @@ -244,9 +244,6 @@ int board_init(void) > writel(pin, &pio->piod.odr); > writel(pin, &pio->piod.owdr); > > - /* Enable Ctrlc */ > - console_init_f(); > - > gd->bd->bi_arch_number = MACH_TYPE_VL_MA2SC; > /* adress of boot parameters */ > gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; > diff --git a/board/atmel/at91sam9261ek/at91sam9261ek.c b/board/atmel/at91sam9261ek/at91sam9261ek.c > index 47ab839..d30a1ee 100644 > --- a/board/atmel/at91sam9261ek/at91sam9261ek.c > +++ b/board/atmel/at91sam9261ek/at91sam9261ek.c > @@ -242,9 +242,6 @@ void lcd_show_board_info(void) > > int board_init(void) > { > - /* Enable Ctrlc */ > - console_init_f(); > - Tested on at91sam9g10ek board. It works well without this. Tested-by: voice.shen@atmel.com > #ifdef CONFIG_AT91SAM9G10EK > /* arch number of AT91SAM9G10EK-Board */ > gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G10EK; > diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c > index 5a04274..d02312c 100644 > --- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c > +++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c > @@ -258,9 +258,6 @@ int board_early_init_f(void) > > int board_init(void) > { > - /* Enable Ctrlc */ > - console_init_f(); > - Tested on at91sam9m10g45ek board. It works well without this. Tested-by: voice.shen@atmel.com > /* arch number of AT91SAM9M10G45EK-Board */ > #ifdef CONFIG_AT91SAM9M10G45EK > gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9M10G45EK; > diff --git a/board/atmel/at91sam9rlek/at91sam9rlek.c b/board/atmel/at91sam9rlek/at91sam9rlek.c > index ef0ddd7..e92ec6e 100644 > --- a/board/atmel/at91sam9rlek/at91sam9rlek.c > +++ b/board/atmel/at91sam9rlek/at91sam9rlek.c > @@ -192,9 +192,6 @@ int board_early_init_f(void) > > int board_init(void) > { > - /* Enable Ctrlc */ > - console_init_f(); > - > /* arch number of AT91SAM9RLEK-Board */ > gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9RLEK; > /* adress of boot parameters */ > diff --git a/board/calao/sbc35_a9g20/sbc35_a9g20.c b/board/calao/sbc35_a9g20/sbc35_a9g20.c > index b6c8791..d3b3684 100644 > --- a/board/calao/sbc35_a9g20/sbc35_a9g20.c > +++ b/board/calao/sbc35_a9g20/sbc35_a9g20.c > @@ -149,9 +149,6 @@ static void sbc35_a9g20_macb_hw_init(void) > > int board_init(void) > { > - /* Enable Ctrlc */ > - console_init_f(); > - > /* adress of boot parameters */ > gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; > > diff --git a/board/calao/tny_a9260/tny_a9260.c b/board/calao/tny_a9260/tny_a9260.c > index 31074d0..86e7e65 100644 > --- a/board/calao/tny_a9260/tny_a9260.c > +++ b/board/calao/tny_a9260/tny_a9260.c > @@ -83,9 +83,6 @@ static void tny_a9260_nand_hw_init(void) > > int board_init(void) > { > - /* Enable Ctrlc */ > - console_init_f(); > - > /* adress of boot parameters */ > gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; > > diff --git a/board/eukrea/cpuat91/cpuat91.c b/board/eukrea/cpuat91/cpuat91.c > index f654f87..c74c3fc 100644 > --- a/board/eukrea/cpuat91/cpuat91.c > +++ b/board/eukrea/cpuat91/cpuat91.c > @@ -43,8 +43,6 @@ DECLARE_GLOBAL_DATA_PTR; > > int board_init(void) > { > - /* Enable Ctrlc */ > - console_init_f(); > /* arch number of CPUAT91-Board */ > gd->bd->bi_arch_number = MACH_TYPE_CPUAT91; > /* adress of boot parameters */ >
> A lot of at91 boards have the console_init_f in board_init. This is useless > cause it was called before by generic code in lib/board.c. > > Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> I have successfully tested this patch for eb_cpux9k2 and vl_ma2sc, so: Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Dear Andreas Bießmann, On 16.08.2012 18:01, Andreas Bießmann wrote: > A lot of at91 boards have the console_init_f in board_init. This is useless > cause it was called before by generic code in lib/board.c. > > Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> > cc: Jens Scharsig <esw@bus-elektronik.de> > cc: Stelian Pop <stelian@popies.net> > cc: Sedji Gaouaou<sedji.gaouaou@atmel.com> > cc: Albin Tonnerre <albin.tonnerre@free-electrons.com> > cc: Eric Benard <eric@eukrea.com> > --- applied to u-boot-atmel/master, thanks! Best regards Andreas Bießmann
diff --git a/board/BuS/eb_cpux9k2/cpux9k2.c b/board/BuS/eb_cpux9k2/cpux9k2.c index 54f9b64..776226f 100644 --- a/board/BuS/eb_cpux9k2/cpux9k2.c +++ b/board/BuS/eb_cpux9k2/cpux9k2.c @@ -59,8 +59,6 @@ DECLARE_GLOBAL_DATA_PTR; int board_init(void) { at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; - /* Enable Ctrlc */ - console_init_f(); /* Correct IRDA resistor problem / Set PA23_TXD in Output */ writel(ATMEL_PMX_AA_TXD2, &pio->pioa.oer); diff --git a/board/BuS/vl_ma2sc/vl_ma2sc.c b/board/BuS/vl_ma2sc/vl_ma2sc.c index 62ed6fb..84b2060 100644 --- a/board/BuS/vl_ma2sc/vl_ma2sc.c +++ b/board/BuS/vl_ma2sc/vl_ma2sc.c @@ -244,9 +244,6 @@ int board_init(void) writel(pin, &pio->piod.odr); writel(pin, &pio->piod.owdr); - /* Enable Ctrlc */ - console_init_f(); - gd->bd->bi_arch_number = MACH_TYPE_VL_MA2SC; /* adress of boot parameters */ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; diff --git a/board/atmel/at91sam9261ek/at91sam9261ek.c b/board/atmel/at91sam9261ek/at91sam9261ek.c index 47ab839..d30a1ee 100644 --- a/board/atmel/at91sam9261ek/at91sam9261ek.c +++ b/board/atmel/at91sam9261ek/at91sam9261ek.c @@ -242,9 +242,6 @@ void lcd_show_board_info(void) int board_init(void) { - /* Enable Ctrlc */ - console_init_f(); - #ifdef CONFIG_AT91SAM9G10EK /* arch number of AT91SAM9G10EK-Board */ gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G10EK; diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c index 5a04274..d02312c 100644 --- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c +++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c @@ -258,9 +258,6 @@ int board_early_init_f(void) int board_init(void) { - /* Enable Ctrlc */ - console_init_f(); - /* arch number of AT91SAM9M10G45EK-Board */ #ifdef CONFIG_AT91SAM9M10G45EK gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9M10G45EK; diff --git a/board/atmel/at91sam9rlek/at91sam9rlek.c b/board/atmel/at91sam9rlek/at91sam9rlek.c index ef0ddd7..e92ec6e 100644 --- a/board/atmel/at91sam9rlek/at91sam9rlek.c +++ b/board/atmel/at91sam9rlek/at91sam9rlek.c @@ -192,9 +192,6 @@ int board_early_init_f(void) int board_init(void) { - /* Enable Ctrlc */ - console_init_f(); - /* arch number of AT91SAM9RLEK-Board */ gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9RLEK; /* adress of boot parameters */ diff --git a/board/calao/sbc35_a9g20/sbc35_a9g20.c b/board/calao/sbc35_a9g20/sbc35_a9g20.c index b6c8791..d3b3684 100644 --- a/board/calao/sbc35_a9g20/sbc35_a9g20.c +++ b/board/calao/sbc35_a9g20/sbc35_a9g20.c @@ -149,9 +149,6 @@ static void sbc35_a9g20_macb_hw_init(void) int board_init(void) { - /* Enable Ctrlc */ - console_init_f(); - /* adress of boot parameters */ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; diff --git a/board/calao/tny_a9260/tny_a9260.c b/board/calao/tny_a9260/tny_a9260.c index 31074d0..86e7e65 100644 --- a/board/calao/tny_a9260/tny_a9260.c +++ b/board/calao/tny_a9260/tny_a9260.c @@ -83,9 +83,6 @@ static void tny_a9260_nand_hw_init(void) int board_init(void) { - /* Enable Ctrlc */ - console_init_f(); - /* adress of boot parameters */ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; diff --git a/board/eukrea/cpuat91/cpuat91.c b/board/eukrea/cpuat91/cpuat91.c index f654f87..c74c3fc 100644 --- a/board/eukrea/cpuat91/cpuat91.c +++ b/board/eukrea/cpuat91/cpuat91.c @@ -43,8 +43,6 @@ DECLARE_GLOBAL_DATA_PTR; int board_init(void) { - /* Enable Ctrlc */ - console_init_f(); /* arch number of CPUAT91-Board */ gd->bd->bi_arch_number = MACH_TYPE_CPUAT91; /* adress of boot parameters */
A lot of at91 boards have the console_init_f in board_init. This is useless cause it was called before by generic code in lib/board.c. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> cc: Jens Scharsig <esw@bus-elektronik.de> cc: Stelian Pop <stelian@popies.net> cc: Sedji Gaouaou<sedji.gaouaou@atmel.com> cc: Albin Tonnerre <albin.tonnerre@free-electrons.com> cc: Eric Benard <eric@eukrea.com> --- board/BuS/eb_cpux9k2/cpux9k2.c | 2 -- board/BuS/vl_ma2sc/vl_ma2sc.c | 3 --- board/atmel/at91sam9261ek/at91sam9261ek.c | 3 --- board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 3 --- board/atmel/at91sam9rlek/at91sam9rlek.c | 3 --- board/calao/sbc35_a9g20/sbc35_a9g20.c | 3 --- board/calao/tny_a9260/tny_a9260.c | 3 --- board/eukrea/cpuat91/cpuat91.c | 2 -- 8 files changed, 22 deletions(-)