@@ -8,7 +8,7 @@ obj-$(CONFIG_USB_PEGASUS) += pegasus.o
obj-$(CONFIG_USB_RTL8150) += rtl8150.o
obj-$(CONFIG_USB_HSO) += hso.o
obj-$(CONFIG_USB_NET_AX8817X) += asix.o
-asix-y := asix_devices.o asix_common.o
+asix-y := asix_devices.o asix_common.o ax88172a.o
obj-$(CONFIG_USB_NET_CDCETHER) += cdc_ether.o
obj-$(CONFIG_USB_NET_CDC_EEM) += cdc_eem.o
obj-$(CONFIG_USB_NET_DM9601) += dm9601.o
@@ -74,6 +74,10 @@
#define AX_CMD_SW_PHY_STATUS 0x21
#define AX_CMD_SW_PHY_SELECT 0x22
+#define AX_PHY_SELECT_MASK (BIT(3) | BIT(2))
+#define AX_PHY_SELECT_INTERNAL 0
+#define AX_PHY_SELECT_EXTERNAL BIT(2)
+
#define AX_MONITOR_MODE 0x01
#define AX_MONITOR_LINK 0x02
#define AX_MONITOR_MAGIC 0x04
@@ -181,6 +185,7 @@ struct sk_buff *asix_tx_fixup(struct usbnet *dev, struct sk_buff *skb,
int asix_set_sw_mii(struct usbnet *dev);
int asix_set_hw_mii(struct usbnet *dev);
+int asix_read_phy_addr(struct usbnet *dev, int internal);
int asix_get_phy_addr(struct usbnet *dev);
int asix_sw_reset(struct usbnet *dev, u8 flags);
@@ -258,8 +258,9 @@ int asix_set_hw_mii(struct usbnet *dev)
return ret;
}
-int asix_get_phy_addr(struct usbnet *dev)
+int asix_read_phy_addr(struct usbnet *dev, int internal)
{
+ int offset = (internal ? 1 : 0);
u8 buf[2];
int ret = asix_read_cmd(dev, AX_CMD_READ_PHY_ID, 0, 0, 2, buf);
@@ -271,12 +272,19 @@ int asix_get_phy_addr(struct usbnet *dev)
}
netdev_dbg(dev->net, "asix_get_phy_addr() returning 0x%04x\n",
*((__le16 *)buf));
- ret = buf[1];
+ ret = buf[offset];
out:
return ret;
}
+int asix_get_phy_addr(struct usbnet *dev)
+{
+ /* return the address of the internal phy */
+ return asix_read_phy_addr(dev, 1);
+}
+
+
int asix_sw_reset(struct usbnet *dev, u8 flags)
{
int ret;
@@ -872,6 +872,8 @@ static const struct driver_info ax88178_info = {
.tx_fixup = asix_tx_fixup,
};
+extern const struct driver_info ax88172a_info;
+
static const struct usb_device_id products [] = {
{
// Linksys USB200M
@@ -997,6 +999,10 @@ static const struct usb_device_id products [] = {
// Asus USB Ethernet Adapter
USB_DEVICE (0x0b95, 0x7e2b),
.driver_info = (unsigned long) &ax88772_info,
+}, {
+ /* ASIX 88172a demo board */
+ USB_DEVICE(0x0b95, 0x172a),
+ .driver_info = (unsigned long) &ax88172a_info,
},
{ }, // END
};
new file mode 100644
@@ -0,0 +1,415 @@
+/*
+ * ASIX AX88172A based USB 2.0 Ethernet Devices
+ * Copyright (C) 2012 OMICRON electronics GmbH
+ *
+ * Supports external PHYs via phylib. Based on the driver for the
+ * AX88772. Original copyrights follow:
+ *
+ * Copyright (C) 2003-2006 David Hollis <dhollis@davehollis.com>
+ * Copyright (C) 2005 Phil Chang <pchang23@sbcglobal.net>
+ * Copyright (C) 2006 James Painter <jamie.painter@iname.com>
+ * Copyright (c) 2002-2003 TiVo Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include "asix.h"
+#include <linux/phy.h>
+
+struct ax88172a_private {
+ struct mii_bus *mdio;
+ struct phy_device *phydev;
+ char phy_name[20];
+ u16 phy_addr;
+ u16 oldmode;
+ int use_embdphy;
+};
+
+/* MDIO read and write wrappers for phylib */
+static int asix_mdio_bus_read(struct mii_bus *bus, int phy_id, int regnum)
+{
+ return asix_mdio_read(((struct usbnet *)bus->priv)->net, phy_id,
+ regnum);
+}
+
+static int asix_mdio_bus_write(struct mii_bus *bus, int phy_id, int regnum,
+ u16 val)
+{
+ asix_mdio_write(((struct usbnet *)bus->priv)->net, phy_id, regnum, val);
+ return 0;
+}
+
+static int ax88172a_ioctl(struct net_device *net, struct ifreq *rq, int cmd)
+{
+ if (!netif_running(net))
+ return -EINVAL;
+
+ if (!net->phydev)
+ return -ENODEV;
+
+ return phy_mii_ioctl(net->phydev, rq, cmd);
+}
+
+/* set MAC link settings according to information from phylib */
+static void ax88172a_adjust_link(struct net_device *netdev)
+{
+ struct phy_device *phydev = netdev->phydev;
+ struct usbnet *dev = netdev_priv(netdev);
+ struct ax88172a_private *priv = dev->driver_priv;
+ u16 mode = 0;
+
+ if (phydev->link) {
+ mode = AX88772_MEDIUM_DEFAULT;
+
+ if (phydev->duplex == DUPLEX_HALF)
+ mode &= ~AX_MEDIUM_FD;
+
+ if (phydev->speed != SPEED_100)
+ mode &= ~AX_MEDIUM_PS;
+ }
+
+ if (mode != priv->oldmode) {
+ asix_write_medium_mode(dev, mode);
+ priv->oldmode = mode;
+ netdev_dbg(netdev, "speed %u duplex %d, setting mode to 0x%04x\n",
+ phydev->speed, phydev->duplex, mode);
+ phy_print_status(phydev);
+ }
+}
+
+static void ax88172a_status(struct usbnet *dev, struct urb *urb)
+{
+ /* link changes are detected by polling the phy */
+}
+
+/* use phylib infrastructure */
+static int ax88172a_init_mdio(struct usbnet *dev)
+{
+ struct ax88172a_private *priv = dev->driver_priv;
+ int ret, i;
+
+ priv->mdio = mdiobus_alloc();
+ if (!priv->mdio) {
+ netdev_err(dev->net, "Could not allocate MDIO bus\n");
+ return -ENOMEM;
+ }
+
+ priv->mdio->priv = (void *)dev;
+ priv->mdio->read = &asix_mdio_bus_read;
+ priv->mdio->write = &asix_mdio_bus_write;
+ priv->mdio->name = "Asix MDIO Bus";
+ /* mii bus name is usb-<usb bus number>-<usb device number> */
+ snprintf(priv->mdio->id, MII_BUS_ID_SIZE, "usb-%03d:%03d",
+ dev->udev->bus->busnum, dev->udev->devnum);
+
+ priv->mdio->irq = kzalloc(sizeof(int) * PHY_MAX_ADDR, GFP_KERNEL);
+ if (!priv->mdio->irq) {
+ netdev_err(dev->net, "Could not allocate mdio->irq\n");
+ ret = -ENOMEM;
+ goto mfree;
+ }
+ for (i = 0; i < PHY_MAX_ADDR; i++)
+ priv->mdio->irq[i] = PHY_POLL;
+
+ ret = mdiobus_register(priv->mdio);
+ if (ret) {
+ netdev_err(dev->net, "Could not register MDIO bus\n");
+ goto ifree;
+ }
+
+ netdev_info(dev->net, "registered mdio bus %s\n", priv->mdio->id);
+ return 0;
+
+ifree:
+ kfree(priv->mdio->irq);
+mfree:
+ mdiobus_free(priv->mdio);
+ return ret;
+}
+
+static void ax88172a_remove_mdio(struct usbnet *dev)
+{
+ struct ax88172a_private *priv = dev->driver_priv;
+
+ netdev_info(dev->net, "deregistering mdio bus %s\n", priv->mdio->id);
+ mdiobus_unregister(priv->mdio);
+ kfree(priv->mdio->irq);
+ mdiobus_free(priv->mdio);
+}
+
+static const struct net_device_ops ax88172a_netdev_ops = {
+ .ndo_open = usbnet_open,
+ .ndo_stop = usbnet_stop,
+ .ndo_start_xmit = usbnet_start_xmit,
+ .ndo_tx_timeout = usbnet_tx_timeout,
+ .ndo_change_mtu = usbnet_change_mtu,
+ .ndo_set_mac_address = asix_set_mac_address,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_do_ioctl = ax88172a_ioctl,
+ .ndo_set_rx_mode = asix_set_multicast,
+};
+
+int ax88172a_get_settings(struct net_device *net, struct ethtool_cmd *cmd)
+{
+ if (!net->phydev)
+ return -ENODEV;
+
+ return phy_ethtool_gset(net->phydev, cmd);
+}
+
+int ax88172a_set_settings(struct net_device *net, struct ethtool_cmd *cmd)
+{
+ if (!net->phydev)
+ return -ENODEV;
+
+ return phy_ethtool_sset(net->phydev, cmd);
+}
+
+int ax88172a_nway_reset(struct net_device *net)
+{
+ if (!net->phydev)
+ return -ENODEV;
+
+ return phy_start_aneg(net->phydev);
+}
+
+static const struct ethtool_ops ax88172a_ethtool_ops = {
+ .get_drvinfo = asix_get_drvinfo,
+ .get_link = usbnet_get_link,
+ .get_msglevel = usbnet_get_msglevel,
+ .set_msglevel = usbnet_set_msglevel,
+ .get_wol = asix_get_wol,
+ .set_wol = asix_set_wol,
+ .get_eeprom_len = asix_get_eeprom_len,
+ .get_eeprom = asix_get_eeprom,
+ .get_settings = ax88172a_get_settings,
+ .set_settings = ax88172a_set_settings,
+ .nway_reset = ax88172a_nway_reset,
+};
+
+static int ax88172a_reset_phy(struct usbnet *dev, int embd_phy)
+{
+ int ret;
+
+ ret = asix_sw_reset(dev, AX_SWRESET_IPPD);
+ if (ret < 0)
+ goto err;
+
+ msleep(150);
+ ret = asix_sw_reset(dev, AX_SWRESET_CLEAR);
+ if (ret < 0)
+ goto err;
+
+ msleep(150);
+
+ ret = asix_sw_reset(dev, embd_phy ? AX_SWRESET_IPRL : AX_SWRESET_IPPD);
+ if (ret < 0)
+ goto err;
+
+ return 0;
+
+err:
+ return ret;
+}
+
+
+static int ax88172a_bind(struct usbnet *dev, struct usb_interface *intf)
+{
+ int ret;
+ struct asix_data *data = (struct asix_data *)&dev->data;
+ u8 buf[ETH_ALEN];
+ struct ax88172a_private *priv;
+
+ data->eeprom_len = AX88772_EEPROM_LEN;
+
+ usbnet_get_endpoints(dev, intf);
+
+ priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+ if (!priv) {
+ netdev_err(dev->net, "Could not allocate memory for private data\n");
+ return -ENOMEM;
+ }
+ dev->driver_priv = priv;
+
+ /* Get the MAC address */
+ ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf);
+ if (ret < 0) {
+ netdev_err(dev->net, "Failed to read MAC address: %d\n", ret);
+ goto free;
+ }
+ memcpy(dev->net->dev_addr, buf, ETH_ALEN);
+
+ dev->net->netdev_ops = &ax88172a_netdev_ops;
+ dev->net->ethtool_ops = &ax88172a_ethtool_ops;
+
+ /* are we using the internal or the external phy? */
+ ret = asix_read_cmd(dev, AX_CMD_SW_PHY_STATUS, 0, 0, 1, buf);
+ if (ret < 0) {
+ netdev_err(dev->net, "Failed to read software interface selection register: %d\n",
+ ret);
+ goto free;
+ }
+
+ netdev_dbg(dev->net, "AX_CMD_SW_PHY_STATUS = 0x%02x\n", buf[0]);
+ switch (buf[0] & AX_PHY_SELECT_MASK) {
+ case AX_PHY_SELECT_INTERNAL:
+ netdev_dbg(dev->net, "use internal phy\n");
+ priv->use_embdphy = 1;
+ break;
+ case AX_PHY_SELECT_EXTERNAL:
+ netdev_dbg(dev->net, "use external phy\n");
+ priv->use_embdphy = 0;
+ break;
+ default:
+ netdev_err(dev->net, "Interface mode not supported by driver\n");
+ goto free;
+ }
+
+ priv->phy_addr = asix_read_phy_addr(dev, priv->use_embdphy);
+ ax88172a_reset_phy(dev, priv->use_embdphy);
+
+ /* Asix framing packs multiple eth frames into a 2K usb bulk transfer */
+ if (dev->driver_info->flags & FLAG_FRAMING_AX) {
+ /* hard_mtu is still the default - the device does not support
+ jumbo eth frames */
+ dev->rx_urb_size = 2048;
+ }
+
+ /* init MDIO bus */
+ ret = ax88172a_init_mdio(dev);
+ if (ret)
+ goto free;
+
+ return 0;
+
+free:
+ kfree(priv);
+ return ret;
+}
+
+static int ax88172a_stop(struct usbnet *dev)
+{
+ struct ax88172a_private *priv = dev->driver_priv;
+
+ netdev_dbg(dev->net, "Stopping interface\n");
+
+ if (priv->phydev) {
+ netdev_info(dev->net, "Disconnecting from phy %s\n",
+ priv->phy_name);
+ phy_stop(priv->phydev);
+ phy_disconnect(priv->phydev);
+ }
+
+ return 0;
+}
+
+static void ax88172a_unbind(struct usbnet *dev, struct usb_interface *intf)
+{
+ struct ax88172a_private *priv = dev->driver_priv;
+
+ ax88172a_remove_mdio(dev);
+ kfree(priv);
+}
+
+static int ax88172a_reset(struct usbnet *dev)
+{
+ struct asix_data *data = (struct asix_data *)&dev->data;
+ struct ax88172a_private *priv = dev->driver_priv;
+ int ret;
+ u16 rx_ctl;
+
+ ax88172a_reset_phy(dev, priv->use_embdphy);
+
+ msleep(150);
+ rx_ctl = asix_read_rx_ctl(dev);
+ netdev_dbg(dev->net, "RX_CTL is 0x%04x after software reset\n", rx_ctl);
+ ret = asix_write_rx_ctl(dev, 0x0000);
+ if (ret < 0)
+ goto out;
+
+ rx_ctl = asix_read_rx_ctl(dev);
+ netdev_dbg(dev->net, "RX_CTL is 0x%04x setting to 0x0000\n", rx_ctl);
+
+ msleep(150);
+
+ ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0,
+ AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,
+ AX88772_IPG2_DEFAULT, 0, NULL);
+ if (ret < 0) {
+ netdev_err(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret);
+ goto out;
+ }
+
+ /* Rewrite MAC address */
+ memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN);
+ ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN,
+ data->mac_addr);
+ if (ret < 0)
+ goto out;
+
+ /* Set RX_CTL to default values with 2k buffer, and enable cactus */
+ ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL);
+ if (ret < 0)
+ goto out;
+
+ rx_ctl = asix_read_rx_ctl(dev);
+ netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n",
+ rx_ctl);
+
+ rx_ctl = asix_read_medium_status(dev);
+ netdev_dbg(dev->net, "Medium Status is 0x%04x after all initializations\n",
+ rx_ctl);
+
+ /* Connect to PHY */
+ snprintf(priv->phy_name, 20, PHY_ID_FMT,
+ priv->mdio->id, priv->phy_addr);
+
+ priv->phydev = phy_connect(dev->net, priv->phy_name,
+ &ax88172a_adjust_link,
+ 0, PHY_INTERFACE_MODE_MII);
+ if (IS_ERR(priv->phydev)) {
+ netdev_err(dev->net, "Could not connect to PHY device %s\n",
+ priv->phy_name);
+ ret = PTR_ERR(priv->phydev);
+ goto out;
+ }
+
+ netdev_info(dev->net, "Connected to phy %s\n", priv->phy_name);
+
+ /* During power-up, the AX88172A set the power down (BMCR_PDOWN)
+ * bit of the PHY. Bring the PHY up again.
+ */
+ genphy_resume(priv->phydev);
+ phy_start(priv->phydev);
+
+ return 0;
+
+out:
+ return ret;
+
+}
+
+const struct driver_info ax88172a_info = {
+ .description = "ASIX AX88172A USB 2.0 Ethernet",
+ .bind = ax88172a_bind,
+ .reset = ax88172a_reset,
+ .stop = ax88172a_stop,
+ .unbind = ax88172a_unbind,
+ .status = ax88172a_status,
+ .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR |
+ FLAG_MULTI_PACKET,
+ .rx_fixup = asix_rx_fixup,
+ .tx_fixup = asix_tx_fixup,
+};
The Asix AX88172A is a USB 2.0 Ethernet interface that supports both an internal PHY as well as an external PHY (connected via MII). This patch adds a driver for the AX88172A and provides support for both modes and the phylib. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> --- drivers/net/usb/Makefile | 2 +- drivers/net/usb/asix.h | 5 + drivers/net/usb/asix_common.c | 12 +- drivers/net/usb/asix_devices.c | 6 + drivers/net/usb/ax88172a.c | 415 ++++++++++++++++++++++++++++++++++++++++ 5 files changed, 437 insertions(+), 3 deletions(-) create mode 100644 drivers/net/usb/ax88172a.c