From patchwork Thu Jun 7 10:06:44 2012 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Valentin Longchamp X-Patchwork-Id: 163572 X-Patchwork-Delegate: prafulla@marvell.com Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Received: from theia.denx.de (theia.denx.de [85.214.87.163]) by ozlabs.org (Postfix) with ESMTP id 8797FB6FF4 for ; Thu, 7 Jun 2012 20:08:28 +1000 (EST) Received: from localhost (localhost [127.0.0.1]) by theia.denx.de (Postfix) with ESMTP id C3E13281BD; Thu, 7 Jun 2012 12:08:00 +0200 (CEST) X-Virus-Scanned: Debian amavisd-new at theia.denx.de Received: from theia.denx.de ([127.0.0.1]) by localhost (theia.denx.de [127.0.0.1]) (amavisd-new, port 10024) with ESMTP id KweSFX6WgW0r; Thu, 7 Jun 2012 12:08:00 +0200 (CEST) Received: from theia.denx.de (localhost [127.0.0.1]) by theia.denx.de (Postfix) with ESMTP id 9886C281F2; Thu, 7 Jun 2012 12:07:16 +0200 (CEST) Received: from localhost (localhost [127.0.0.1]) by theia.denx.de (Postfix) with ESMTP id 1C8BC281DA for ; Thu, 7 Jun 2012 12:07:06 +0200 (CEST) X-Virus-Scanned: Debian amavisd-new at theia.denx.de Received: from theia.denx.de ([127.0.0.1]) by localhost (theia.denx.de [127.0.0.1]) (amavisd-new, port 10024) with ESMTP id YqpYhrymDk10 for ; Thu, 7 Jun 2012 12:07:04 +0200 (CEST) X-policyd-weight: NOT_IN_SBL_XBL_SPAMHAUS=-1.5 NOT_IN_SPAMCOP=-1.5 NOT_IN_BL_NJABL=-1.5 (only DNSBL check requested) Received: from mail.ch.keymile.com (mail.ch.keymile.com [193.17.201.103]) by theia.denx.de (Postfix) with SMTP id 6DB36281C1 for ; Thu, 7 Jun 2012 12:07:03 +0200 (CEST) Received: from SRVCHBER1212.ch.keymile.net ([172.31.32.9]) by eSafe SMTP Relay 1334159602; Thu, 07 Jun 2012 12:07:03 +0200 Received: from chber1-10533x.ch.keymile.net ([172.31.40.3]) by SRVCHBER1212.ch.keymile.net with Microsoft SMTPSVC(6.0.3790.4675); Thu, 7 Jun 2012 12:07:01 +0200 From: Valentin Longchamp To: To: prafulla@mavell.com Date: Thu, 7 Jun 2012 12:06:44 +0200 Message-Id: <1339063620-8890-5-git-send-email-valentin.longchamp@keymile.com> X-Mailer: git-send-email 1.7.1 In-Reply-To: <1339063620-8890-1-git-send-email-valentin.longchamp@keymile.com> References: <1339063620-8890-1-git-send-email-valentin.longchamp@keymile.com> X-OriginalArrivalTime: 07 Jun 2012 10:07:01.0992 (UTC) FILETIME=[4872EE80:01CD4495] X-ESAFE-STATUS: [srvchber1306.keymile.net] Mail allowed Cc: Valentin Longchamp , Gerlando@theia.denx.de, u-boot@lists.denx.de, Holger Brunck , Falauto Subject: [U-Boot] [PATCH 04/20] arm/km: add kmnusa board support X-BeenThere: u-boot@lists.denx.de X-Mailman-Version: 2.1.11 Precedence: list List-Id: U-Boot discussion List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , MIME-Version: 1.0 Sender: u-boot-bounces@lists.denx.de Errors-To: u-boot-bounces@lists.denx.de From: Holger Brunck This board is similar to portl2, but it has the u-boot environment in a SPI NOR flash and not in an i2c eeprom like portl2 have. Some other details: - IVM EEPROM is at adress: pca9547:70:9 - PCI is enabled - PIGGY4 is connected via MV88E6352 simple switch. There is no phy between the simple switch and the kirkwood. Signed-off-by: Holger Brunck Signed-off-by: Valentin Longchamp cc: Gerlando Falauto cc: Prafulla Wadaskar --- MAINTAINERS | 1 + board/keymile/km_arm/128M16-1.cfg | 294 +++++++++++++++++++++++++++++++++++++ board/keymile/km_arm/km_arm.c | 9 +- boards.cfg | 1 + include/configs/km/km_arm.h | 44 +++++- include/configs/km_kirkwood.h | 67 +++++++-- 6 files changed, 392 insertions(+), 24 deletions(-) create mode 100644 board/keymile/km_arm/128M16-1.cfg diff --git a/MAINTAINERS b/MAINTAINERS index 0445539..aa11268 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -738,6 +738,7 @@ Sergey Lapin Valentin Longchamp km_kirkwood ARM926EJS (Kirkwood SoC) + kmnusa ARM926EJS (Kirkwood SoC) mgcoge3un ARM926EJS (Kirkwood SoC) portl2 ARM926EJS (Kirkwood SoC) diff --git a/board/keymile/km_arm/128M16-1.cfg b/board/keymile/km_arm/128M16-1.cfg new file mode 100644 index 0000000..bcce907 --- /dev/null +++ b/board/keymile/km_arm/128M16-1.cfg @@ -0,0 +1,294 @@ +# +# (C) Copyright 2010 +# Heiko Schocher, DENX Software Engineering, hs@denx.de. +# +# (C) Copyright 2012 +# Valentin Longchamp, Keymile AG, valentin.longchamp@keymile.com +# Stefan Bigler, Keymile AG, stefan.bigler@keymile.com +# +# (C) Copyright 2012 +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# +# Refer docs/README.kwimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM spi # Boot from SPI flash + +DATA 0xFFD10000 0x01112222 # MPP Control 0 Register +# bit 3-0: 2, MPPSel0 SPI_CSn (1=NF_IO[2]) +# bit 7-4: 2, MPPSel1 SPI_SI (1=NF_IO[3]) +# bit 12-8: 2, MPPSel2 SPI_SCK (1=NF_IO[4]) +# bit 15-12: 2, MPPSel3 SPI_SO (1=NF_IO[5]) +# bit 19-16: 1, MPPSel4 NF_IO[6] +# bit 23-20: 1, MPPSel5 NF_IO[7] +# bit 27-24: 1, MPPSel6 SYSRST_O +# bit 31-28: 0, MPPSel7 GPO[7] + +DATA 0xFFD10004 0x03303300 # MPP Control 1 Register +# bit 3-0: 0, MPPSel8 GPIO[8] +# bit 7-4: 0, MPPSel9 GPIO[9] +# bit 12-8: 3, MPPSel10 UA0_TXD +# bit 15-12: 3, MPPSel11 UA0_RXD +# bit 19-16: 0, MPPSel12 not connected +# bit 23-20: 3, MPPSel13 UA1_TXD +# bit 27-24: 3, MPPSel14 UA1_RXD +# bit 31-28: 0, MPPSel15 GPIO[15] + +DATA 0xFFD10008 0x00001100 # MPP Control 2 Register +# bit 3-0: 0, MPPSel16 GPIO[16] +# bit 7-4: 0, MPPSel17 not connected +# bit 12-8: 1, MPPSel18 NF_IO[0] +# bit 15-12: 1, MPPSel19 NF_IO[1] +# bit 19-16: 0, MPPSel20 GPIO[20] +# bit 23-20: 0, MPPSel21 GPIO[21] +# bit 27-24: 0, MPPSel22 GPIO[22] +# bit 31-28: 0, MPPSel23 GPIO[23] + +# MPP Control 3-6 Register untouched (MPP24-49) + +DATA 0xFFD100E0 0x1B1B1B1B # IO Configuration 0 Register +# bit 2-0: 3, Reserved +# bit 5-3: 3, Reserved +# bit 6: 0, Reserved +# bit 7: 0, RGMII-pads voltage = 3.3V +# bit 10-8: 3, Reserved +# bit 13-11: 3, Reserved +# bit 14: 0, Reserved +# bit 15: 0, MPP RGMII-pads voltage = 3.3V +# bit 31-16 0x1B1B, Reserved + +DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register +# bit 0-1: 2, Tag RAM RTC RAM0 +# bit 3-2: 1, Tag RAM WTC RAM0 +# bit 7-4: 6, Reserve +# bit 9-8: 2, Valid RAM RTC RAM +# bit 11-10: 1, Valid RAM WTC RAM +# bit 13-12: 2, Dirty RAM RTC RAM +# bit 15-14: 1, Dirty RAM WTC RAM +# bit 17-16: 2, Data RAM RTC RAM0 +# bit 19-18: 1, Data RAM WTC RAM0 +# bit 21-20: 2, Data RAM RTC RAM1 +# bit 23-22: 1, Data RAM WTC RAM1 +# bit 25-24: 2, Data RAM RTC RAM2 +# bit 27-26: 1, Data RAM WTC RAM2 +# bit 29-28: 2, Data RAM RTC RAM3 +# bit 31-30: 1, Data RAM WTC RAM4 + +DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register +# bit 15-0: ???, Reserve +# bit 17-16: 2, ECC RAM RTC RAM0 +# bit 19-18: 1, ECC RAM WTC RAM0 +# bit 31-20: ???,Reserve + +DATA 0xFFD20154 0x00000200 # CPU RAM Management Control3 Register +# bit 23-0: 0x000200, Addr Config tuning +# bit 31-24: 0, Reserved + +# ??? Missing register # CPU RAM Management Control2 Register + +DATA 0xFFD2014C 0x00001C00 # CPU RAM Management Control1 Register +# bit 15-0: 0x1C00, Opmux Tuning +# bit 31-16: 0, Pc Dp Tuning + +DATA 0xFFD20148 0x00000001 # CPU RAM Management Control0 Register +# bit 1-0: 1, addr clk tune +# bit 3-2: 0, reserved +# bit 5-4: 0, dtcmp clk tune +# bit 7-6: 0, reserved +# bit 9-8: 0, macdrv clk tune +# bit 11-10: 0, opmuxgm2 clk tune +# bit 15-14: 0, rf clk tune +# bit 17-16: 0, rfbypass clk tune +# bit 19-18: 0, pc dp clk tune +# bit 23-20: 0, icache clk tune +# bit 27:24: 0, dcache clk tune +# bit 31:28: 0, regfile tunin + +# SDRAM initalization +DATA 0xFFD01400 0x430004E0 # SDRAM Configuration Register +# bit 13-0: 0x4E0, DDR2 clks refresh rate +# bit 14: 0, reserved +# bit 15: 0, reserved +# bit 16: 0, CPU to Dram Write buffer policy +# bit 17: 0, Enable Registered DIMM or Equivalent Sampling Logic +# bit 19-18: 0, reserved +# bit 23-20: 0, reserved +# bit 24: 1, enable exit self refresh mode on DDR access +# bit 25: 1, required +# bit 29-26: 0, reserved +# bit 31-30: 1, reserved + +DATA 0xFFD01404 0x36543000 # DDR Controller Control Low +# bit 3-0: 0, reserved +# bit 4: 0, 2T mode =addr/cmd in same cycle +# bit 5: 0, clk is driven during self refresh, we don't care for APX +# bit 6: 0, use recommended falling edge of clk for addr/cmd +# bit 7-11: 0, reserved +# bit 12-13: 1, reserved, required 1 +# bit 14: 0, input buffer always powered up +# bit 17-15: 0, reserved +# bit 18: 1, cpu lock transaction enabled +# bit 19: 0, reserved +# bit 23-20: 5, recommended value for CL=4 and STARTBURST_DEL disabled bit31=0 +# bit 27-24: 6, CL+1, STARTBURST sample stages, for freqs 200-399MHz, unbuffered DIMM +# bit 30-28: 3, required +# bit 31: 0,no additional STARTBURST delay + +DATA 0xFFD01408 0x2302444e # DDR Timing (Low) (active cycles value +1) +# bit 3-0: 0xE, TRAS, 15 clk (45 ns) +# bit 7-4: 0x4, TRCD, 5 clk (15 ns) +# bit 11-8: 0x4, TRP, 5 clk (15 ns) +# bit 15-12: 0x4, TWR, 5 clk (15 ns) +# bit 19-16: 0x2, TWTR, 3 clk (7.5 ns) +# bit 20: 0, extended TRAS msb +# bit 23-21: 0, reserved +# bit 27-24: 0x3, TRRD, 4 clk (10 ns) +# bit 31-28: 0x2, TRTP, 3 clk (7.5 ns) + +DATA 0xFFD0140C 0x0000003e # DDR Timing (High) +# bit 6-0: 0x3E, TRFC, 63 clk (195 ns) +# bit 8-7: 0, TR2R +# bit 10-9: 0, TR2W +# bit 12-11: 0, TW2W +# bit 31-13: 0, reserved + +DATA 0xFFD01410 0x00000001 # DDR Address Control +# bit 1-0: 1, Cs0width=x16 +# bit 3-2: 0, Cs0size=2Gb +# bit 5-4: 0, Cs1width=nonexistent +# bit 7-6: 0, Cs1size =nonexistent +# bit 9-8: 0, Cs2width=nonexistent +# bit 11-10: 0, Cs2size =nonexistent +# bit 13-12: 0, Cs3width=nonexistent +# bit 15-14: 0, Cs3size =nonexistent +# bit 16: 0, Cs0AddrSel +# bit 17: 0, Cs1AddrSel +# bit 18: 0, Cs2AddrSel +# bit 19: 0, Cs3AddrSel +# bit 31-20: 0, required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit 0: 0, OpenPage enabled +# bit 31-1: 0, required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit 3-0: 0, DDR cmd +# bit 31-4: 0, required + +DATA 0xFFD0141C 0x00000652 # DDR Mode +# bit 2-0: 2, Burst Length = 4 +# bit 3: 0, Burst Type +# bit 6-4: 5, CAS Latency = 5 +# bit 7: 0, Test mode +# bit 8: 0, DLL Reset +# bit 11-9: 3, Write recovery for auto-precharge must be 3 +# bit 12: 0, Active power down exit time, fast exit +# bit 14-13: 0, reserved +# bit 31-15: 0, reserved + +DATA 0xFFD01420 0x00000006 # DDR Extended Mode +# bit 0: 0, DDR DLL enabled +# bit 1: 1, DDR drive strength reduced +# bit 2: 1, DDR ODT control lsb, 75 ohm termination [RTT0] +# bit 5-3: 0, required +# bit 6: 0, DDR ODT control msb, 75 ohm termination [RTT1] +# bit 9-7: 0, required +# bit 10: 0, differential DQS enabled +# bit 11: 0, required +# bit 12: 0, DDR output buffer enabled +# bit 31-13: 0 required + +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High +# bit 2-0: 7, required +# bit 3: 1, MBUS Burst Chop disabled +# bit 6-4: 7, required +# bit 7: 0, reserved +# bit 8: 1, add sample stage required for f > 266 MHz +# bit 9: 0, no half clock cycle addition to dataout +# bit 10: 0, 1/4 clock cycle skew enabled for addr/ctl signals +# bit 11: 0, 1/4 clock cycle skew disabled for write mesh +# bit 15-12:0xf, required +# bit 31-16: 0, required + +DATA 0xFFD01428 0x00084520 # DDR2 SDRAM Timing Low +# bit 3-0: 0, required +# bit 7-4: 2, M_ODT assertion 2 cycles after read start command +# bit 11-8: 5, M_ODT de-assertion 5 cycles after read start command +# (ODT turn off delay 2,5 clk cycles) +# bit 15-12: 4, internal ODT time based on bit 7-4 +# with the considered SDRAM internal delay +# bit 19-16: 8, internal ODT de-assertion based on bit 11-8 +# with the considered SDRAM internal delay +# bit 31-20: 0, required + +DATA 0xFFD0147c 0x00008452 # DDR2 SDRAM Timing High +# bit 3-0: 2, M_ODT assertion same as bit 11-8 +# bit 7-4: 5, M_ODT de-assertion same as bit 15-12 +# bit 11-8: 4, internal ODT assertion 2 cycles after write start command +# with the considered SDRAM internal delay +# bit 15-12: 8, internal ODT de-assertion 5 cycles after write start command +# with the considered SDRAM internal delay + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +# bit 23-0: 0, reserved +# bit 31-24: 0, CPU CS Window0 Base Address, addr bits [31:24] + +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size +# bit 0: 1, Window enabled +# bit 1: 0, Write Protect disabled +# bit 3-2: 0, CS0 hit selected +# bit 23-4:ones, required +# bit 31-24: 0x0F, Size (i.e. 256MB) + +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low) +# bit 3-0: 0, ODT0Rd, MODT[0] not asserted during read from DRAM CS0 +# bit 7-4: 0, ODT0Rd, MODT[1] not asserted +# bit 11-8: 0, required +# big 15-11: 0, required +# bit 19-16: 1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 +# bit 23-20: 0, ODT0Wr, MODT[1] not asserted +# bit 27-24: 0, required +# bit 31-28: 0, required + +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit 1-0: 0, ODT0 controlled by ODT Control (low) register above +# bit 3-2: 0, ODT1 controlled by register +# bit 31-4: 0, required + +DATA 0xFFD0149C 0x0000E801 # CPU ODT Control +# bit 3-0: 1, ODTRd, Internal ODT asserted during read from DRAM bank0 +# bit 7-4: 0, ODTWr, Internal ODT not asserted during write to DRAM +# bit 9-8: 0, ODTEn, controlled by ODTRd and ODTWr +# bit 11-10: 2, DQ_ODTSel. ODT select turned on, 75 ohm +# bit 13-12: 2, STARTBURST ODT buffer selected, 75 ohm +# bit 14: 1, STARTBURST ODT enabled +# bit 15: 1, Use ODT Block + +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +# bit 0: 1, enable DDR init upon this register write +# bit 31-1: 0, reserved + +# End of Header extension +DATA 0x0 0x0 diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c index e4ae1fb..ffe13cd 100644 --- a/board/keymile/km_arm/km_arm.c +++ b/board/keymile/km_arm/km_arm.c @@ -133,10 +133,11 @@ int startup_allowed(void) } #endif -#if (defined(CONFIG_MGCOGE3UN)|defined(CONFIG_PORTL2)) +#if (defined(CONFIG_MGCOGE3UN)|defined(CONFIG_PORTL2)| \ + defined(CONFIG_KM_PIGGY4_88E6352)) /* - * These two boards have always ethernet present. Its connected to the mv - * switch. + * All boards with PIGGY4 connected via a simple switch have ethernet always + * present. */ int ethernet_present(void) { @@ -384,7 +385,7 @@ void reset_phy(void) /* reset the phy */ miiphy_reset(name, CONFIG_PHY_BASE_ADR); } -#else +#elif !defined(CONFIG_KM_PIGGY4_88E6352) /* Configure and enable MV88E1118 PHY on the piggy*/ void reset_phy(void) { diff --git a/boards.cfg b/boards.cfg index b711e0d..1a4c2ad 100644 --- a/boards.cfg +++ b/boards.cfg @@ -140,6 +140,7 @@ pogo_e02 arm arm926ejs - clouden dns325 arm arm926ejs - d-link kirkwood km_kirkwood arm arm926ejs km_arm keymile kirkwood km_kirkwood:KM_KIRKWOOD,KM_DISABLE_PCI km_kirkwood_pci arm arm926ejs km_arm keymile kirkwood km_kirkwood:KM_KIRKWOOD_PCI,KM_RECONFIG_XLX +kmnusa arm arm926ejs km_arm keymile kirkwood km_kirkwood:KM_NUSA mgcoge3un arm arm926ejs km_arm keymile kirkwood portl2 arm arm926ejs km_arm keymile kirkwood inetspace_v2 arm arm926ejs netspace_v2 LaCie kirkwood lacie_kw:INETSPACE_V2 diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h index 28b5021..a35ef61 100644 --- a/include/configs/km/km_arm.h +++ b/include/configs/km/km_arm.h @@ -57,6 +57,13 @@ #define CONFIG_CMD_SF #define CONFIG_SOFT_I2C /* I2C bit-banged */ +#if defined CONFIG_KM_ENV_IS_IN_SPI_NOR +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 5000000 +#define CONFIG_ENV_SPI_MODE SPI_MODE_3 +#endif + #include "asm/arch/config.h" #define CONFIG_SYS_TEXT_BASE 0x07d00000 /* code address before reloc */ @@ -211,6 +218,15 @@ int get_scl(void); /* * Environment variables configurations */ +#if defined CONFIG_KM_ENV_IS_IN_SPI_NOR +#define CONFIG_ENV_IS_IN_SPI_FLASH /* use SPI-Flash for environment vars */ +#define CONFIG_ENV_OFFSET 0xc0000 /* no bracets! */ +#define CONFIG_ENV_SIZE 0x02000 /* Size of Environment */ +#define CONFIG_ENV_SECT_SIZE 0x10000 +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_TOTAL_SIZE 0x20000 /* no bracets! */ +#else #define CONFIG_ENV_IS_IN_EEPROM /* use EEPROM for environment vars */ #define CONFIG_SYS_DEF_EEPROM_ADDR 0x50 #define CONFIG_ENV_EEPROM_IS_ON_I2C @@ -218,11 +234,11 @@ int get_scl(void); #define CONFIG_ENV_OFFSET 0x0 /* no bracets! */ #define CONFIG_ENV_SIZE (0x2000 - CONFIG_ENV_OFFSET) #define CONFIG_I2C_ENV_EEPROM_BUS KM_ENV_BUS "\0" - -/* offset redund: (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */ -#define CONFIG_SYS_REDUNDAND_ENVIRONMENT #define CONFIG_ENV_OFFSET_REDUND 0x2000 /* no bracets! */ #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) +#endif + +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT #define CONFIG_SPI_FLASH #define CONFIG_SPI_FLASH_STMICRO @@ -245,17 +261,27 @@ int get_scl(void); "sf write ${load_addr_r} 0 ${filesize};" \ "spi off\0" -/* - * Default environment variables - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_KM_DEF_ENV \ +#if defined CONFIG_KM_ENV_IS_IN_SPI_NOR +#define CONFIG_KM_NEW_ENV \ + "newenv=sf probe 0;" \ + "sf erase " xstr(CONFIG_ENV_OFFSET) " " \ + xstr(CONFIG_ENV_TOTAL_SIZE)"\0" +#else +#define CONFIG_KM_NEW_ENV \ "newenv=setenv addr 0x100000 && " \ "i2c dev 1; mw.b ${addr} 0 4 && " \ "eeprom write " xstr(CONFIG_SYS_DEF_EEPROM_ADDR) \ " ${addr} " xstr(CONFIG_ENV_OFFSET) " 4 && " \ "eeprom write " xstr(CONFIG_SYS_DEF_EEPROM_ADDR) \ - " ${addr} " xstr(CONFIG_ENV_OFFSET_REDUND) " 4\0" \ + " ${addr} " xstr(CONFIG_ENV_OFFSET_REDUND) " 4\0" +#endif + +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_KM_DEF_ENV \ + CONFIG_KM_NEW_ENV \ "arch=arm\0" \ "EEprom_ivm=" KM_IVM_BUS "\0" \ "" diff --git a/include/configs/km_kirkwood.h b/include/configs/km_kirkwood.h index f639edc..97aa617 100644 --- a/include/configs/km_kirkwood.h +++ b/include/configs/km_kirkwood.h @@ -6,8 +6,9 @@ * (C) Copyright 2009 * Stefan Roese, DENX Software Engineering, sr@denx.de. * - * (C) Copyright 2011 - * Holger Brunck, Keymile GmbH Hannover, holger.brunck@keymile.de + * (C) Copyright 2011-2012 + * Holger Brunck, Keymile GmbH Hannover, holger.brunck@keymile.com + * Valentin Longchamp, Keymile AG, valentin.longchamp@keymile.com * * See file CREDITS for list of people who contributed to this * project. @@ -36,23 +37,67 @@ #ifndef _CONFIG_KM_KIRKWOOD_H #define _CONFIG_KM_KIRKWOOD_H -/* include common defines/options for all arm based Keymile boards */ -#include "km/km_arm.h" - -/* - * Version number information - */ #if defined(CONFIG_KM_KIRKWOOD) -#define CONFIG_IDENT_STRING "\nKeymile Kirkwood" +#define CONFIG_IDENT_STRING "\nKeymile Kirkwood" #undef CONFIG_KIRKWOOD_PCIE_INIT +#define KM_IVM_BUS "pca9544a:70:9" /* I2C2 (Mux-Port 1)*/ #elif defined(CONFIG_KM_KIRKWOOD_PCI) -#define CONFIG_IDENT_STRING "\nKeymile Kirkwood PCI" +#define CONFIG_IDENT_STRING "\nKeymile Kirkwood PCI" +#define KM_IVM_BUS "pca9544a:70:9" /* I2C2 (Mux-Port 1)*/ +/* KM_NUSA */ +#elif defined(CONFIG_KM_NUSA) +#define KM_IVM_BUS "pca9547:70:9" /* I2C2 (Mux-Port 1)*/ +#define CONFIG_IDENT_STRING "\nKeymile NUSA" +#undef CONFIG_SYS_KWD_CONFIG +#define CONFIG_SYS_KWD_CONFIG \ + $(SRCTREE)/$(CONFIG_BOARDDIR)/128M16-1.cfg +#define CONFIG_KM_ENV_IS_IN_SPI_NOR +#define CONFIG_KM_FPGA_CONFIG +#define CONFIG_KM_PIGGY4_88E6352 + +#else +#error ("Board unsupported") #endif +/* include common defines/options for all arm based Keymile boards */ +#include "km/km_arm.h" + #define CONFIG_HOSTNAME km_kirkwood -#define KM_IVM_BUS "pca9544a:70:9" /* I2C2 (Mux-Port 1)*/ +#ifndef CONFIG_KM_ENV_IS_IN_SPI_NOR #define KM_ENV_BUS "pca9544a:70:d" /* I2C2 (Mux-Port 5)*/ +#endif + +#if defined(CONFIG_KM_PIGGY4_88E6352) +/* + * Some keymile boards like mgcoge5un & nusa1 have their PIGGY4 connected via + * an Marvell 88E6352 simple switch. + * In this case we have to change the default settings for the etherent mac. + * There is NO ethernet phy. The ARM and Switch are conencted directly over + * RGMII in MAC-MAC mode + * In this case 1GBit full duplex and autoneg off + */ +#define PORT_SERIAL_CONTROL_VALUE ( \ + MVGBE_FORCE_LINK_PASS | \ + MVGBE_DIS_AUTO_NEG_FOR_DUPLX | \ + MVGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL | \ + MVGBE_ADV_NO_FLOW_CTRL | \ + MVGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX | \ + MVGBE_FORCE_BP_MODE_NO_JAM | \ + (1 << 9) /* Reserved bit has to be 1 */ | \ + MVGBE_DO_NOT_FORCE_LINK_FAIL | \ + MVGBE_DIS_AUTO_NEG_SPEED_GMII | \ + MVGBE_DTE_ADV_0 | \ + MVGBE_MIIPHY_MAC_MODE | \ + MVGBE_AUTO_NEG_NO_CHANGE | \ + MVGBE_MAX_RX_PACKET_1552BYTE | \ + MVGBE_CLR_EXT_LOOPBACK | \ + MVGBE_SET_FULL_DUPLEX_MODE | \ + MVGBE_EN_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX |\ + MVGBE_SET_GMII_SPEED_TO_1000 |\ + MVGBE_SET_MII_SPEED_TO_100) + +#endif /* GPIO Pin from kirkwood connected to PROGRAM_B pin of the xilinx FPGA */ #define KM_XLX_PROGRAM_B_PIN 39