@@ -70,12 +70,4 @@ config WIZNET_BUS_ANY
Performance may decrease compared to explicitly selected bus mode.
endchoice
-config WIZNET_TX_FLOW
- bool "Use transmit flow control"
- depends on WIZNET_W5100 || WIZNET_W5300
- default y
- help
- This enables transmit flow control for WIZnet chips.
- If unsure, say Y.
-
endif # NET_VENDOR_WIZNET
@@ -441,8 +441,7 @@ static int w5100_start_tx(struct sk_buff *skb, struct net_device *ndev)
struct w5100_priv *priv = netdev_priv(ndev);
u16 offset;
- if (IS_ENABLED(CONFIG_WIZNET_TX_FLOW))
- netif_stop_queue(ndev);
+ netif_stop_queue(ndev);
offset = w5100_read16(priv, W5100_S0_TX_WR);
w5100_writebuf(priv, offset, skb->data, skb->len);
@@ -517,7 +516,7 @@ static irqreturn_t w5100_interrupt(int irq, void *ndev_instance)
w5100_write(priv, W5100_S0_IR, ir);
mmiowb();
- if (IS_ENABLED(CONFIG_WIZNET_TX_FLOW) && (ir & S0_IR_SENDOK)) {
+ if (ir & S0_IR_SENDOK) {
netif_dbg(priv, tx_done, ndev, "tx done\n");
netif_wake_queue(ndev);
}
@@ -273,9 +273,7 @@ static void w5300_hw_start(struct w5300_priv *priv)
S0_MR_MACRAW : S0_MR_MACRAW_MF);
mmiowb();
w5300_command(priv, S0_CR_OPEN);
- w5300_write(priv, W5300_S0_IMR, IS_ENABLED(CONFIG_WIZNET_TX_FLOW) ?
- S0_IR_RECV | S0_IR_SENDOK :
- S0_IR_RECV);
+ w5300_write(priv, W5300_S0_IMR, S0_IR_RECV | S0_IR_SENDOK);
w5300_write(priv, W5300_IMR, IR_S0);
mmiowb();
}
@@ -371,8 +369,7 @@ static int w5300_start_tx(struct sk_buff *skb, struct net_device *ndev)
{
struct w5300_priv *priv = netdev_priv(ndev);
- if (IS_ENABLED(CONFIG_WIZNET_TX_FLOW))
- netif_stop_queue(ndev);
+ netif_stop_queue(ndev);
w5300_write_frame(priv, skb->data, skb->len);
mmiowb();
@@ -439,7 +436,7 @@ static irqreturn_t w5300_interrupt(int irq, void *ndev_instance)
w5300_write(priv, W5300_S0_IR, ir);
mmiowb();
- if (IS_ENABLED(CONFIG_WIZNET_TX_FLOW) && (ir & S0_IR_SENDOK)) {
+ if (ir & S0_IR_SENDOK) {
netif_dbg(priv, tx_done, ndev, "tx done\n");
netif_wake_queue(ndev);
}
This option was there for debugging race conditions, just remove it, and assume TX_FLOW is always enabled. Signed-off-by: Mike Sinkovsky <msink@permonline.ru> --- This replaces patch from Paul Gortmaker: "[PATCH 3/5] drivers/net: remove IS_ENABLED usage from wiznet drivers The use of IS_ENABLED in C code (vs just in CPP #if directives) causes us to carry the burden of a huge autoconf.h file. It is also misleading in that a casual inspection of the code would leave one thinking that the if statements were evaluated at runtime, when TX_FLOW is a Kconfig bool and hence evaluated at configure time as an either/or." Just remove this option instead. drivers/net/ethernet/wiznet/Kconfig | 8 -------- drivers/net/ethernet/wiznet/w5100.c | 5 ++--- drivers/net/ethernet/wiznet/w5300.c | 9 +++------ 3 files changed, 5 insertions(+), 17 deletions(-)