@@ -174,6 +174,7 @@ source "drivers/net/ethernet/tile/Kconfig"
source "drivers/net/ethernet/toshiba/Kconfig"
source "drivers/net/ethernet/tundra/Kconfig"
source "drivers/net/ethernet/via/Kconfig"
+source "drivers/net/ethernet/wiznet/Kconfig"
source "drivers/net/ethernet/xilinx/Kconfig"
source "drivers/net/ethernet/xircom/Kconfig"
@@ -73,5 +73,6 @@ obj-$(CONFIG_TILE_NET) += tile/
obj-$(CONFIG_NET_VENDOR_TOSHIBA) += toshiba/
obj-$(CONFIG_NET_VENDOR_TUNDRA) += tundra/
obj-$(CONFIG_NET_VENDOR_VIA) += via/
+obj-$(CONFIG_NET_VENDOR_WIZNET) += wiznet/
obj-$(CONFIG_NET_VENDOR_XILINX) += xilinx/
obj-$(CONFIG_NET_VENDOR_XIRCOM) += xircom/
new file mode 100644
@@ -0,0 +1,61 @@
+#
+# WIZnet device configuration
+#
+
+config NET_VENDOR_WIZNET
+ bool "WIZnet devices"
+ default y
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about WIZnet devices. If you say Y, you will be asked
+ for your specific card in the following questions.
+
+if NET_VENDOR_WIZNET
+
+config WIZNET_W5300
+ tristate "WIZnet W5300 Ethernet support"
+ depends on ARM || BLACKFIN
+ ---help---
+ Support for WIZnet W5300 chips.
+
+ W5300 is a single chip with integrated 10/100 Ethernet MAC,
+ PHY and hardware TCP/IP stack, but this driver is limited to
+ the MAC and PHY functions only, onchip TCP/IP is unused.
+
+ To compile this driver as a module, choose M here: the module
+ will be called w5300.
+
+choice
+ prompt "WIZnet interface mode"
+ depends on NET_VENDOR_WIZNET
+ default WIZNET_BUS_ANY
+
+config WIZNET_BUS_DIRECT
+ bool "Direct address bus mode"
+ ---help---
+ In direct address mode host system can directly access W5300 registers
+ after mapping to Memory-mapped I/O Space.
+ 0x400 bytes are required for memory space.
+
+config WIZNET_BUS_INDIRECT
+ bool "Indirect address bus mode"
+ ---help---
+ In indirect address mode host system indirectly accesses registers by
+ using Indirect Mode Address Register (IDM_AR) and Indirect Mode Data
+ Register (IDM_DR), which are directly mapped to Memory-mapped I/O Space.
+ Only 0x06 bytes are required for memory space.
+
+config WIZNET_BUS_ANY
+ bool "Select interface mode in runtime"
+ ---help---
+ If interface mode is unknown in compile time, you can selectied it
+ in runtime.
+ Performance may decrease compared to explicitly selected bus mode.
+endchoice
+
+endif # NET_VENDOR_WIZNET
new file mode 100644
@@ -0,0 +1 @@
+obj-$(CONFIG_WIZNET_W5300) += w5300.o
new file mode 100644
@@ -0,0 +1,707 @@
+/*
+ * Ethernet driver for the WIZnet W5300 chip.
+ *
+ * Copyright (C) 2008-2009 WIZnet Co.,Ltd.
+ * Copyright (C) 2011 Taehun Kim <kth3321 <at> gmail.com>
+ * Copyright (C) 2012 Mike Sinkovsky <msink@permonline.ru>
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/skbuff.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/wiznet.h>
+
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#include <linux/slab.h>
+
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/interrupt.h>
+#include <linux/gpio.h>
+
+#define DRV_NAME "WIZnet W5300"
+#define DRV_VERSION "2012-03-24"
+
+MODULE_DESCRIPTION(DRV_NAME" Ethernet driver v"DRV_VERSION);
+MODULE_AUTHOR("Mike Sinkovsky <msink@permonline.ru>");
+MODULE_ALIAS("platform:"KBUILD_MODNAME);
+MODULE_LICENSE("GPL");
+
+/*
+ * Registers
+ */
+#define W5300_MR 0x0000 /* Mode Register */
+#define MR_DBW (1 << 15) /* Data bus width */
+#define MR_MPF (1 << 14) /* Mac layer pause frame */
+#define MR_WDF(n) (((n)&7)<<11) /* Write data fetch time */
+#define MR_RDH (1 << 10) /* Read data hold time */
+#define MR_FS (1 << 8) /* FIFO swap */
+#define MR_RST (1 << 7) /* S/W reset */
+#define MR_PB (1 << 4) /* Ping block */
+#define MR_DBS (1 << 2) /* Data bus swap */
+#define MR_IND (1 << 0) /* Indirect mode */
+#define W5300_IR 0x0002 /* Interrupt Register */
+#define W5300_IMR 0x0004 /* Interrupt Mask Register */
+#define IR_S0 0x0001 /* S0 interrupt */
+#define W5300_SHARL 0x0008 /* Source MAC address (0123) */
+#define W5300_SHARH 0x000c /* Source MAC address (45) */
+#define W5300_TMSRL 0x0020 /* Transmit Memory Size (0123) */
+#define W5300_TMSRH 0x0024 /* Transmit Memory Size (4567) */
+#define W5300_RMSRL 0x0028 /* Receive Memory Size (0123) */
+#define W5300_RMSRH 0x002c /* Receive Memory Size (4567) */
+#define W5300_MTYPE 0x0030 /* Memory Type */
+#define W5300_IDR 0x00fe /* Chip ID register */
+#define IDR_W5300 0x5300 /* =0x5300 for WIZnet W5300 */
+#define W5300_S0_MR 0x0200 /* S0 Mode Register */
+#define S0_MR_CLOSE 0x0000 /* Close mode */
+#define S0_MR_MACRAW 0x0004 /* MAC RAW mode (promiscous) */
+#define S0_MR_MACRAW_MF 0x0044 /* MAC RAW mode (filtered) */
+#define W5300_S0_CR 0x0202 /* S0 Command Register */
+#define S0_CR_OPEN 0x0001 /* OPEN command */
+#define S0_CR_CLOSE 0x0010 /* CLOSE command */
+#define S0_CR_SEND 0x0020 /* SEND command */
+#define S0_CR_RECV 0x0040 /* RECV command */
+#define W5300_S0_IMR 0x0204 /* S0 Interrupt Mask Register */
+#define W5300_S0_IR 0x0206 /* S0 Interrupt Register */
+#define S0_IR_RECV 0x0004 /* Receive interrupt */
+#define W5300_S0_SSR 0x0208 /* S0 Socket Status Register */
+#define W5300_S0_TX_WRSR 0x0220 /* S0 TX Write Size Register */
+#define W5300_S0_TX_FSR 0x0224 /* S0 TX Free Size Register */
+#define W5300_S0_RX_RSR 0x0228 /* S0 Received data Size */
+#define W5300_S0_TX_FIFO 0x022e /* S0 Transmit FIFO */
+#define W5300_S0_RX_FIFO 0x0230 /* S0 Receive FIFO */
+#define W5300_REGS_LEN 0x0400
+
+/*
+ * Frame size is hardwired to 1514 bytes (including header),
+ * => MTU for 802.1Q frames must me set to 1500-4 = 1496
+ */
+#define W5300_HARD_MTU 1500
+
+/*
+ * Device driver private data structure
+ */
+struct w5300_private {
+ void __iomem *base;
+ int irq;
+ int link_irq;
+ int link_gpio;
+
+ u16 (*read) (struct w5300_private *priv, u16 addr);
+ void (*write)(struct w5300_private *priv, u16 addr, u16 data);
+ spinlock_t reg_lock;
+ bool indirect;
+ bool promisc;
+
+ struct napi_struct napi;
+ struct net_device *ndev;
+ u32 msg_enable;
+};
+
+/************************************************************************
+ *
+ * Lowlevel I/O functions
+ *
+ ***********************************************************************/
+
+/*
+ * In direct address mode host system can directly access W5300 registers
+ * after mapping to Memory-mapped I/O Space.
+ *
+ * 0x400 bytes are required for memory space.
+ */
+static inline u16
+w5300_read_direct(struct w5300_private *priv, u16 addr)
+{
+ return ioread16(priv->base + addr);
+}
+
+static inline void
+w5300_write_direct(struct w5300_private *priv, u16 addr, u16 data)
+{
+ iowrite16(data, priv->base + addr);
+ mmiowb();
+}
+
+/*
+ * In indirect address mode host system indirectly accesses registers by
+ * using Indirect Mode Address Register (IDM_AR) and Indirect Mode Data
+ * Register (IDM_DR), which are directly mapped to Memory-mapped I/O Space.
+ * Mode Register (MR) is directly accessible.
+ *
+ * Only 0x06 bytes are required for memory space.
+ */
+#define W5300_IDM_AR 0x002 /* Indirect Mode Address Register */
+#define W5300_IDM_DR 0x004 /* Indirect Mode Data Register */
+
+static inline u16
+w5300_read_indirect(struct w5300_private *priv, u16 addr)
+{
+ unsigned long flags;
+ u16 data;
+
+ spin_lock_irqsave(&priv->reg_lock, flags);
+ w5300_write_direct(priv, W5300_IDM_AR, addr);
+ data = w5300_read_direct(priv, W5300_IDM_DR);
+ spin_unlock_irqrestore(&priv->reg_lock, flags);
+
+ return data;
+}
+
+static inline void
+w5300_write_indirect(struct w5300_private *priv, u16 addr, u16 data)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->reg_lock, flags);
+ w5300_write_direct(priv, W5300_IDM_AR, addr);
+ w5300_write_direct(priv, W5300_IDM_DR, data);
+ spin_unlock_irqrestore(&priv->reg_lock, flags);
+}
+
+#if defined(CONFIG_WIZNET_BUS_DIRECT)
+#define w5300_read w5300_read_direct
+#define w5300_write w5300_write_direct
+
+#elif defined(CONFIG_WIZNET_BUS_INDIRECT)
+#define w5300_read w5300_read_indirect
+#define w5300_write w5300_write_indirect
+
+#else /* CONFIG_WIZNET_BUS_ANY */
+#define w5300_read priv->read
+#define w5300_write priv->write
+#endif
+
+static inline u32
+w5300_read32(struct w5300_private *priv, u16 addr)
+{
+ u32 data;
+ data = w5300_read(priv, addr) << 16;
+ data |= w5300_read(priv, addr + 2);
+ return data;
+}
+
+static inline void
+w5300_write32(struct w5300_private *priv, u16 addr, u32 data)
+{
+ w5300_write(priv, addr, data >> 16);
+ w5300_write(priv, addr + 2, data);
+}
+
+static inline int w5300_command(struct w5300_private *priv, u16 cmd)
+{
+ unsigned long timeout = jiffies + msecs_to_jiffies(100);
+
+ w5300_write(priv, W5300_S0_CR, cmd);
+
+ while (w5300_read(priv, W5300_S0_CR) != 0) {
+ if (time_after(jiffies, timeout))
+ return -EIO;
+ cpu_relax();
+ }
+
+ return 0;
+}
+
+static void w5300_read_frame(struct w5300_private *priv, u8 *data, int len)
+{
+ u16 fifo;
+ int i;
+
+ for (i = 0; i < len; i += 2) {
+ fifo = w5300_read(priv, W5300_S0_RX_FIFO);
+ *data++ = fifo >> 8;
+ *data++ = fifo;
+ }
+ fifo = w5300_read(priv, W5300_S0_RX_FIFO);
+ fifo = w5300_read(priv, W5300_S0_RX_FIFO);
+}
+
+static void w5300_write_frame(struct w5300_private *priv, u8 *data, int len)
+{
+ u16 fifo;
+ int i;
+
+ for (i = 0; i < len; i += 2) {
+ fifo = *data++ << 8;
+ fifo |= *data++;
+ w5300_write(priv, W5300_S0_TX_FIFO, fifo);
+ }
+ w5300_write32(priv, W5300_S0_TX_WRSR, len);
+ w5300_command(priv, S0_CR_SEND);
+}
+
+static void w5300_write_macaddr(struct w5300_private *priv)
+{
+ struct net_device *ndev = priv->ndev;
+ w5300_write32(priv, W5300_SHARL,
+ ndev->dev_addr[0] << 24 |
+ ndev->dev_addr[1] << 16 |
+ ndev->dev_addr[2] << 8 |
+ ndev->dev_addr[3]);
+ w5300_write(priv, W5300_SHARH,
+ ndev->dev_addr[4] << 8 |
+ ndev->dev_addr[5]);
+}
+
+static void w5300_hw_reset(struct w5300_private *priv)
+{
+ w5300_write_direct(priv, W5300_MR, MR_RST);
+ mdelay(5);
+ w5300_write_direct(priv, W5300_MR, priv->indirect ?
+ MR_WDF(7) | MR_PB | MR_IND :
+ MR_WDF(7) | MR_PB);
+ w5300_write(priv, W5300_IMR, 0);
+
+ /*
+ * Configure 128K of internal memory
+ * as 64K RX fifo and 64K TX fifo
+ */
+ w5300_write32(priv, W5300_RMSRL, 64 << 24);
+ w5300_write32(priv, W5300_RMSRH, 0);
+ w5300_write32(priv, W5300_TMSRL, 64 << 24);
+ w5300_write32(priv, W5300_TMSRH, 0);
+ w5300_write(priv, W5300_MTYPE, 0x00ff);
+
+ w5300_write_macaddr(priv);
+}
+
+static void w5300_hw_start(struct w5300_private *priv)
+{
+ w5300_write(priv, W5300_S0_MR, priv->promisc ?
+ S0_MR_MACRAW :
+ S0_MR_MACRAW_MF);
+ w5300_command(priv, S0_CR_OPEN);
+ w5300_write(priv, W5300_S0_IMR, S0_IR_RECV);
+ w5300_write(priv, W5300_IMR, IR_S0);
+}
+
+/***********************************************************************
+ *
+ * Device driver functions / callbacks
+ *
+ ***********************************************************************/
+
+static void w5300_get_drvinfo(struct net_device *ndev,
+ struct ethtool_drvinfo *info)
+{
+ strlcpy(info->driver, DRV_NAME, sizeof(info->driver));
+ strlcpy(info->version, DRV_VERSION, sizeof(info->version));
+ strlcpy(info->bus_info, dev_name(ndev->dev.parent),
+ sizeof(info->bus_info));
+}
+
+static u32 w5300_get_link(struct net_device *ndev)
+{
+ struct w5300_private *priv = netdev_priv(ndev);
+
+ if (priv->link_gpio < 0)
+ return 1;
+
+ return !!gpio_get_value(priv->link_gpio);
+}
+
+static u32 w5300_get_msglevel(struct net_device *ndev)
+{
+ struct w5300_private *priv = netdev_priv(ndev);
+
+ return priv->msg_enable;
+}
+
+static void w5300_set_msglevel(struct net_device *ndev, u32 value)
+{
+ struct w5300_private *priv = netdev_priv(ndev);
+
+ priv->msg_enable = value;
+}
+
+static int w5300_get_regs_len(struct net_device *ndev)
+{
+ return W5300_REGS_LEN;
+}
+
+static void w5300_get_regs(struct net_device *ndev,
+ struct ethtool_regs *regs, void *_buf)
+{
+ struct w5300_private *priv = netdev_priv(ndev);
+ u8 *buf = _buf;
+ u16 addr;
+ u16 data;
+
+ regs->version = 1;
+ for (addr = 0; addr < W5300_REGS_LEN; addr += 2) {
+ switch (addr & 0x23f) {
+ case W5300_S0_TX_FIFO: /* cannot read TX_FIFO */
+ case W5300_S0_RX_FIFO: /* cannot read RX_FIFO */
+ data = 0xffff;
+ break;
+ default:
+ data = w5300_read(priv, addr);
+ break;
+ }
+ *buf++ = data >> 8;
+ *buf++ = data;
+ }
+}
+
+static void w5300_tx_timeout(struct net_device *ndev)
+{
+ struct w5300_private *priv = netdev_priv(ndev);
+
+ if (netif_msg_timer(priv))
+ netdev_err(ndev, "transmit timeout\n");
+
+ netif_stop_queue(ndev);
+ w5300_hw_reset(priv);
+ w5300_hw_start(priv);
+ ndev->stats.tx_errors++;
+ ndev->trans_start = jiffies;
+ netif_wake_queue(ndev);
+}
+
+static int w5300_start_tx(struct sk_buff *skb, struct net_device *ndev)
+{
+ struct w5300_private *priv = netdev_priv(ndev);
+
+ if (unlikely(w5300_read32(priv, W5300_S0_TX_FSR) < skb->len)) {
+ ndev->stats.tx_dropped++;
+ return NETDEV_TX_BUSY;
+ }
+
+ w5300_write_frame(priv, skb->data, skb->len);
+ ndev->stats.tx_packets++;
+ ndev->stats.tx_bytes += skb->len;
+ dev_kfree_skb(skb);
+
+ return NETDEV_TX_OK;
+}
+
+static int w5300_napi_poll(struct napi_struct *napi, int budget)
+{
+ struct w5300_private *priv =
+ container_of(napi, struct w5300_private, napi);
+ struct net_device *ndev = priv->ndev;
+ struct sk_buff *skb;
+ int rx_count;
+ u16 rx_size;
+
+ for (rx_count = 0; rx_count < budget; rx_count++) {
+ u32 rx_fifo_size = w5300_read32(priv, W5300_S0_RX_RSR);
+ if (rx_fifo_size == 0)
+ break;
+
+ rx_size = w5300_read(priv, W5300_S0_RX_FIFO);
+
+ skb = netdev_alloc_skb_ip_align(ndev, roundup(rx_size, 2));
+ if (unlikely(!skb)) {
+ u32 i;
+ for (i = 0; i < rx_fifo_size; i += 2)
+ w5300_read(priv, W5300_S0_RX_FIFO);
+ ndev->stats.rx_dropped++;
+ return -ENOMEM;
+ }
+
+ skb_put(skb, rx_size);
+ w5300_read_frame(priv, skb->data, rx_size);
+ skb->protocol = eth_type_trans(skb, ndev);
+
+ netif_receive_skb(skb);
+ ndev->stats.rx_packets++;
+ ndev->stats.rx_bytes += rx_size;
+ }
+
+ if (rx_count < budget) {
+ w5300_write(priv, W5300_IMR, IR_S0);
+ napi_complete(napi);
+ }
+
+ return rx_count;
+}
+
+static irqreturn_t w5300_start_rx(int irq, void *ndev_instance)
+{
+ struct net_device *ndev = ndev_instance;
+ struct w5300_private *priv = netdev_priv(ndev);
+
+ w5300_write(priv, W5300_S0_IR, S0_IR_RECV);
+
+ if (napi_schedule_prep(&priv->napi)) {
+ w5300_write(priv, W5300_IMR, 0);
+ __napi_schedule(&priv->napi);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t w5300_detect_link(int irq, void *ndev_instance)
+{
+ struct net_device *ndev = ndev_instance;
+ struct w5300_private *priv = netdev_priv(ndev);
+
+ if (netif_running(ndev)) {
+ if (gpio_get_value(priv->link_gpio) != 0) {
+ if (netif_msg_link(priv))
+ netdev_info(ndev, "link is Up\n");
+ netif_carrier_on(ndev);
+ } else {
+ if (netif_msg_link(priv))
+ netdev_info(ndev, "link is Down\n");
+ netif_carrier_off(ndev);
+ }
+ }
+
+ return IRQ_HANDLED;
+}
+
+static void w5300_set_rx_mode(struct net_device *ndev)
+{
+ struct w5300_private *priv = netdev_priv(ndev);
+ bool set_promisc = (ndev->flags & IFF_PROMISC) != 0;
+
+ if (priv->promisc != set_promisc) {
+ priv->promisc = set_promisc;
+ w5300_hw_start(priv);
+ }
+}
+
+static int w5300_set_macaddr(struct net_device *ndev, void *addr)
+{
+ struct w5300_private *priv = netdev_priv(ndev);
+ struct sockaddr *sock_addr = addr;
+
+ if (!is_valid_ether_addr(sock_addr->sa_data))
+ return -EADDRNOTAVAIL;
+ memcpy(ndev->dev_addr, sock_addr->sa_data, ETH_ALEN);
+ ndev->addr_assign_type &= ~NET_ADDR_RANDOM;
+
+ w5300_write_macaddr(priv);
+ return 0;
+}
+
+static int w5300_open(struct net_device *ndev)
+{
+ struct w5300_private *priv = netdev_priv(ndev);
+
+ if (netif_msg_ifup(priv))
+ netdev_dbg(ndev, "enabling\n");
+
+ if (!is_valid_ether_addr(ndev->dev_addr))
+ return -EINVAL;
+
+ w5300_hw_start(priv);
+
+ napi_enable(&priv->napi);
+ netif_start_queue(ndev);
+ if (priv->link_gpio < 0 || gpio_get_value(priv->link_gpio))
+ netif_carrier_on(ndev);
+ return 0;
+}
+
+static int w5300_stop(struct net_device *ndev)
+{
+ struct w5300_private *priv = netdev_priv(ndev);
+
+ if (netif_msg_ifdown(priv))
+ netdev_dbg(ndev, "shutting down\n");
+
+ w5300_write(priv, W5300_IMR, 0);
+ w5300_write(priv, W5300_S0_CR, S0_CR_CLOSE);
+
+ netif_carrier_off(ndev);
+ netif_stop_queue(ndev);
+ napi_disable(&priv->napi);
+ return 0;
+}
+
+static const struct ethtool_ops w5300_ethtool_ops = {
+ .get_drvinfo = w5300_get_drvinfo,
+ .get_msglevel = w5300_get_msglevel,
+ .set_msglevel = w5300_set_msglevel,
+ .get_link = w5300_get_link,
+ .get_regs_len = w5300_get_regs_len,
+ .get_regs = w5300_get_regs,
+};
+
+static const struct net_device_ops w5300_netdev_ops = {
+ .ndo_open = w5300_open,
+ .ndo_stop = w5300_stop,
+ .ndo_start_xmit = w5300_start_tx,
+ .ndo_tx_timeout = w5300_tx_timeout,
+ .ndo_set_rx_mode = w5300_set_rx_mode,
+ .ndo_set_mac_address = w5300_set_macaddr,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+};
+
+static int __devinit w5300_hw_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct net_device *ndev = platform_get_drvdata(pdev);
+ struct w5300_private *priv = netdev_priv(ndev);
+ const char *name = netdev_name(ndev);
+ struct resource *link;
+ struct resource *mem;
+ int mem_size;
+ int irq;
+ int ret;
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!mem)
+ return -ENXIO;
+ mem_size = resource_size(mem);
+ if (!devm_request_mem_region(dev, mem->start, mem_size, name))
+ return -EBUSY;
+ priv->base = devm_ioremap(dev, mem->start, mem_size);
+ if (!priv->base)
+ return -EBUSY;
+
+ spin_lock_init(&priv->reg_lock);
+ priv->indirect = mem_size < 0x400;
+ if (priv->indirect) {
+ priv->read = w5300_read_indirect;
+ priv->write = w5300_write_indirect;
+ } else {
+ priv->read = w5300_read_direct;
+ priv->write = w5300_write_direct;
+ }
+ w5300_hw_reset(priv);
+ if (w5300_read(priv, W5300_IDR) != IDR_W5300)
+ return -ENODEV;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+ ret = devm_request_irq(dev, irq, w5300_start_rx,
+ IRQ_TYPE_LEVEL_LOW, name, ndev);
+ if (ret < 0)
+ return ret;
+ priv->irq = irq;
+
+ link = platform_get_resource(pdev, IORESOURCE_IO, 0);
+ if (!link) {
+ priv->link_gpio = -1;
+ } else {
+ char *link_name = devm_kzalloc(dev, 16, GFP_KERNEL);
+ if (!link_name)
+ return -ENOMEM;
+ snprintf(link_name, 16, "%s-link", name);
+ priv->link_gpio = link->start;
+ priv->link_irq = gpio_to_irq(priv->link_gpio);
+ if (request_irq(priv->link_irq, w5300_detect_link,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+ link_name, priv->ndev) < 0)
+ priv->link_gpio = -1;
+ }
+
+ netdev_info(ndev, "at 0x%llx irq %d\n", (u64)mem->start, irq);
+ return 0;
+}
+
+static int __devinit w5300_probe(struct platform_device *pdev)
+{
+ struct wiznet_platform_data *data = pdev->dev.platform_data;
+ struct w5300_private *priv;
+ struct net_device *ndev;
+ int ret;
+
+ ndev = alloc_etherdev(sizeof(*priv));
+ if (!ndev)
+ return -ENOMEM;
+ SET_NETDEV_DEV(ndev, &pdev->dev);
+ platform_set_drvdata(pdev, ndev);
+ priv = netdev_priv(ndev);
+ priv->ndev = ndev;
+
+ ether_setup(ndev);
+ ndev->netdev_ops = &w5300_netdev_ops;
+ ndev->ethtool_ops = &w5300_ethtool_ops;
+ ndev->watchdog_timeo = 2 * HZ;
+ netif_napi_add(ndev, &priv->napi, w5300_napi_poll, 16);
+ ret = register_netdev(ndev);
+ if (ret < 0)
+ goto fail;
+
+ if (data && is_valid_ether_addr(data->mac_addr)) {
+ memcpy(ndev->dev_addr, data->mac_addr, ETH_ALEN);
+ } else {
+ random_ether_addr(ndev->dev_addr);
+ ndev->addr_assign_type |= NET_ADDR_RANDOM;
+ }
+ ret = w5300_hw_probe(pdev);
+ if (ret < 0)
+ goto fail;
+
+ return 0;
+
+fail: netdev_info(ndev, "probe failed (%d)\n", ret);
+ unregister_netdev(ndev);
+ free_netdev(ndev);
+ platform_set_drvdata(pdev, NULL);
+ return ret;
+}
+
+static int __devexit w5300_remove(struct platform_device *pdev)
+{
+ struct net_device *ndev = platform_get_drvdata(pdev);
+
+ unregister_netdev(ndev);
+ free_netdev(ndev);
+ platform_set_drvdata(pdev, NULL);
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int w5300_suspend(struct platform_device *pdev, pm_message_t mesg)
+{
+ struct net_device *ndev = platform_get_drvdata(pdev);
+ struct w5300_private *priv = netdev_priv(ndev);
+
+ if (netif_running(ndev)) {
+ netif_carrier_off(ndev);
+ netif_device_detach(ndev);
+
+ w5300_write(priv, W5300_IMR, 0);
+ w5300_command(priv, S0_CR_CLOSE);
+ }
+ return 0;
+}
+
+static int w5300_resume(struct platform_device *pdev)
+{
+ struct net_device *ndev = platform_get_drvdata(pdev);
+ struct w5300_private *priv = netdev_priv(ndev);
+
+ if (netif_running(ndev)) {
+ w5300_hw_reset(priv);
+ w5300_hw_start(priv);
+
+ netif_device_attach(ndev);
+ if (priv->link_gpio < 0 || gpio_get_value(priv->link_gpio))
+ netif_carrier_on(ndev);
+ }
+ return 0;
+}
+#endif /* CONFIG_PM */
+
+static SIMPLE_DEV_PM_OPS(w5300_pm_ops, w5300_suspend, w5300_resume);
+
+static struct platform_driver w5300_driver = {
+ .driver = {
+ .name = KBUILD_MODNAME,
+ .owner = THIS_MODULE,
+ .pm = &w5300_pm_ops,
+ },
+ .probe = w5300_probe,
+ .remove = __devexit_p(w5300_remove),
+};
+
+module_platform_driver(w5300_driver);
new file mode 100644
@@ -0,0 +1,16 @@
+/*
+ * Ethernet driver for the WIZnet W5300 chip.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef PLATFORM_DATA_WIZNET_H
+#define PLATFORM_DATA_WIZNET_H
+
+#include <linux/if_ether.h>
+
+struct wiznet_platform_data {
+ u8 mac_addr[ETH_ALEN];
+};
+
+#endif /* PLATFORM_DATA_WIZNET_H */
Based on original driver from chip manufacturer, but nearly full rewite. Tested and used in production with Blackfin BF531 embedded processor. Signed-off-by: Mike Sinkovsky <msink@permonline.ru> --- v3: - reading macaddr from platform_data - ethtool: get_link, get_msglevel, set_msglevel - more cleanups v2: - corrected handling of NET_ADDR_RANDOM flag - support for WIZNET_BUS_ANY mode - link detection using gpio - registers read using ethtool - more cleanups drivers/net/ethernet/Kconfig | 1 + drivers/net/ethernet/Makefile | 1 + drivers/net/ethernet/wiznet/Kconfig | 61 +++ drivers/net/ethernet/wiznet/Makefile | 1 + drivers/net/ethernet/wiznet/w5300.c | 707 ++++++++++++++++++++++++++++++++++ include/linux/platform_data/wiznet.h | 16 + 6 files changed, 787 insertions(+), 0 deletions(-) create mode 100644 drivers/net/ethernet/wiznet/Kconfig create mode 100644 drivers/net/ethernet/wiznet/Makefile create mode 100644 drivers/net/ethernet/wiznet/w5300.c create mode 100644 include/linux/platform_data/wiznet.h -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html